i really dont know what to do, trying to install a custom recovery for first time, my phone got stuck on samsung screen, i did all the steps from a google search (which i cant post, xda forum rules, but they were the instructions to flash the stock room) but odin's get stuck on system.img, i really dont know what else to to, if someone could help me please. i got the stock rom from sammobile, and already tried changing usb cable
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900HXXU1ANJ2_G900HUWM1ANJ1_G900HXXU1ANJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> param.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hi
Thanks for writing to us at XDA Assist. Please standby while we have your thread/question moved to the appropriate sub-forum for your device.
For future reference you can find your device sub-forum here (bookmark/subscribe this):
Samsung Galaxy S 5
Within that section you will find a dedicated q&a sub-forum (this is where your thread is going to be moved to):
Galaxy S 5 Q&A, Help & Troubleshooting
Good luck!
Related
(Previous thread can be seen here)
Hi all,
Thank you for whom reads this thread. - Very recently I tried to root my Samsung Galaxy Note 3. The method I was using was the Kingo application that isn't prohibited on the forum which I now know. At this point I am unsure what to do, besides flashing this but I am unsure if this method will work. Plus I do not know how to flash this or where to even begin.
Basically in short, I tried doing the following:
Root with the Kingo root application that I got from the official site.
After I used Wanam Exposed to customize my stock ROM.
Played on my phone for a bit and then I got a random error: "Unfortunately, System Ui has stopped"
I posted a thread about this issue (without much detail on what I was doing) and I was recommended to flash these stock files which didn't work. Here is the following errors while I try to flash the file in Odin:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_N900VVRUBMI9_N900VVZWMI9_1671014_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
At this point I do not know what to do. I am not hard bricked but I assume I am soft bricked because my phone will not boot into my system because of the error I posted above. If anyone can get me on the right track this would be great. Thank you.
the same thing has happened to me before and i plugged my phone into the computer and used the built in verizon upgrade center and went to the repair section
Storm.hf said:
(Previous thread can be seen here)
Hi all,
Thank you for whom reads this thread. - Very recently I tried to root my Samsung Galaxy Note 3. The method I was using was the Kingo application that isn't prohibited on the forum which I now know. At this point I am unsure what to do, besides flashing this but I am unsure if this method will work. Plus I do not know how to flash this or where to even begin.
Basically in short, I tried doing the following:
Root with the Kingo root application that I got from the official site.
After I used Wanam Exposed to customize my stock ROM.
Played on my phone for a bit and then I got a random error: "Unfortunately, System Ui has stopped"
I posted a thread about this issue (without much detail on what I was doing) and I was recommended to flash these stock files which didn't work. Here is the following errors while I try to flash the file in Odin:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_N900VVRUBMI9_N900VVZWMI9_1671014_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
At this point I do not know what to do. I am not hard bricked but I assume I am soft bricked because my phone will not boot into my system because of the error I posted above. If anyone can get me on the right track this would be great. Thank you.
Click to expand...
Click to collapse
Could you please link me to the software
Sent from my GT-P5113 using xda app-developers app
I think your phone may have had firmware that was later than what you were trying to flash. From what you posted you were flashing mi9 which was the first one with initial released phones. They would explain the soft brick. Then there was update MJ7 and now there is MJE. I would suggest finding the MJ7 tar file and try that and see if that will fix the soft brick. If same results then try MJE.
Hope this helps.
Tap'n & Talk'n on my Note 3
I bricked my phone while trying to flash jasminerom.
I can't seem to get it back to stock with Odin. I'm using the correct pit file and stock but I always end up with this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUCNC4_N900VVZWCNC4_N900VVRUCNC4_HOME.tar.m d5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? Please help!
I have the SM-N900V with android 4.4.2
Does your phone boot? If so, turn it back on, enable USB debugging and try again.
Does USB Debugging help us to flash the firmware too ?...
Regards
No it does not aid flashing .
OP should download another firmware and try again .
After a failed root attempt my s5 is stuck on the first start up screen, the one that says powered by android at the bottom. When I try to flash the stock ROM using Odin I get an error message on my phone saying:
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
This is my Odin log (I am using odin v3.09):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be appreciated.
Please help!
SecretAgentJeb said:
After a failed root attempt my s5 is stuck on the first start up screen, the one that says powered by android at the bottom. When I try to flash the stock ROM using Odin I get an error message on my phone saying:
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
This is my Odin log (I am using odin v3.09):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be appreciated.
Click to expand...
Click to collapse
SecretAgentJeb said:
Please help!
Click to expand...
Click to collapse
Greetings,
Thank you for using XDA Assist. First, please do not bump a thread until at least 24 hours have passed. XDA Assist is a very busy forum and your questions will be addressed when someone is available to answer. I will, however, move this thread to your device's Q&A forum. Good luck!
I want to know this as well. I excluded the problem of different PC and different USB cable. Why is it so hard to flash back stock ROM?
I think you are trying to flash an old version, or one not meant for the sprint phone. The file you are flashing ends in NCB, the latest is OK4.
As the title says I'm trying to flash a stock rom on this S5 so I can use the phone which is stuck on the activation lock screen. I'll post my Odin log below. Does anyone have any helpful guides or information I'm really trying to get this phone up and running but can't seem to have any luck. I'd truly appreciate your guys help, thank you so much for taking the time to read this post and help a fellow user out. Much love
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900VVRU1BOA8_G900VVZW1BOA8_G900VVRU1BOA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Need help i get soft bricked my samsung a5 2017 (LDU)
i brought LDU & installed A520FXXU2BQIH_A520FOJV2BQJ1_PAK from sammobile after installation phone sticked into GOOGLE FRP after 2-3 hours searching on youtube i found a method for google frp reset by COMBINATION file so i installed this file COMBINATION_FAC_FA60_A520FXXU3ARA3 in that 7.0 firmware A520FXXU2BQIH_A520FOJV2BQJ1_PAK now device get bricked also then i try more options too then i download
A520FXXU4BRA8_A520FOXA3BQL2_XEF & COMBINATION_FAC_FA60_A520FXXU4ARA4 still fail at wright system in odin also get back to 1st installed 7.0 firmware now get red error on device screen SW REV. CHECK FAIL. DEVICE: 4 BINARY:3
kindly help
Is your problem fixed or not.... If not the problem is with you binary.. You have to have one.. Your best and easiest way to solve your problem is to start all over again and flash your stock rom back and then root your phone.
Don't forget to backup your phone
thank you a lots for reply bro i did same what you said about me but all fail again take a look im not geek to understand kindly give me step by step solution.
with combination file in AP
COMBINATION_FAC_FA60_A520FXXU3ARA3_FAC3ARA3_CL12800524_QB16363926_REV00_user_mid_noship
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1509 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
AND WITH FULL FIRMWARE
AP_A520FXXU3BQLA_CL12637612_QB16162045_REV00_user_low_ship_meta
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4624 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ALL FAIL DEVICE TILL THE SAME KINDLY HELP
Single file
download and load single file firmwares of the country
ozkanasilioglu said:
download and load single file firmwares of the country
Click to expand...
Click to collapse
single file not available on sammobile.com
now what to do sir
How do u find the firmware and can I use any version as long as its the country firmware