I got my new yotaphone 2 delivered today and noticed there is a feint rattle from the camera end. Does anyone else hear a rattle with even a gentle wave fore and back of your yd201?
It still seems to take good pictures though in strong light at least. Focus runs in and out and jumps about in anything less.
The rattle doesn't appear to be the volume keys as i ejected them and held the slide. Still got a rattle though not as obvious as previously. The sound doesn't seem to be from as low down as the keys anyway. Seems higher near the camera.
The rattle is the imei info card thing. It hangs loose inside the SIM tray port, remove the SIM tray and you can slide it out. Space saving measure I suppose
zute333 said:
The rattle is the imei info card thing. It hangs loose inside the SIM tray port, remove the SIM tray and you can slide it out. Space saving measure I suppose
Click to expand...
Click to collapse
Note that it still rattles very slightly even if I hold the slide.
Oh? Oh well then, maybe i'm wrong and there is just something else loose knocking about, or the slide itself is a perpetual rattler. Doesn't seem to be causing any problems, hope it doesn't annoy you too much. I'm too in love with the phone to care
I RMA'd it and now have a replacement. If I remove the volume keys and SIM and hold the slide there are no rattles.
Must have had something loose inside the previous phone.
Cool, glad you eventually got a properly put together model then.
Related
Hi, I was wondering if anyone suffers from screen corruption when recieving an incoming call. My screen sometimes (maybe 6 times out of 10) will go into landscape mode and result in some corruption. It will revert to normal when I actually answer the call. Sometimes, I am unable to answer the call and the caller will be sent to voicemail even though I click the green send button.
Has anyone come accross anything like this?
Thanks.
Well, there is a chance that I am psychic... Are you storing your device in the supplied holster? It has been noted that the sensor which indicates the keyboard is fully out appears to be either magnetic or sensitive to magnetic fields. So it is entirely possible that it is getting temporarily switched to landscape as you drag it out of the holster.
Neat experiment to prove this sensitivity. Take your K-Jam, turn on the power. Now, with the keyboard stowed, take your holster flap place the fuzzy side against the back of your device and slowly move it up around the right-hand edge of your device. At some point along the way your device will flip to landscape.
Robert Harrold
Houston, TX
Ahh, its done magnetically? I was worried a microswitch would eventually wear out ;p
you are so true, it happens to me all the time, it even answers calls automaticaly, I thought I was pressing some buttons while taking it out of the holster but I tried your little experiment , it was positive all the time,
Now, how to solve this without throwing the holster away?
I notices that it happens more when the screen is facing inside, when I insert it screen outside it rarely happens!
you are so true, it happens to me all the time, it even answers calls automaticaly, I thought I was pressing some buttons while taking it out of the holster but I tried your little experiment , it was positive all the time,
Now, how to solve this without throwing the holster away?
I notices that it happens more when the screen is facing inside, when I insert it screen outside it rarely happens!
robinton said:
Well, there is a chance that I am psychic... Are you storing your device in the supplied holster? It has been noted that the sensor which indicates the keyboard is fully out appears to be either magnetic or sensitive to magnetic fields. So it is entirely possible that it is getting temporarily switched to landscape as you drag it out of the holster.
Neat experiment to prove this sensitivity. Take your K-Jam, turn on the power. Now, with the keyboard stowed, take your holster flap place the fuzzy side against the back of your device and slowly move it up around the right-hand edge of your device. At some point along the way your device will flip to landscape.
Robert Harrold
Houston, TX
Click to expand...
Click to collapse
Robert, I will pay to have you read my fortune any day!! Exactly as you said. Really gutted about having to ditch the holster, but I would rather be able to answer my calls effectively.
Thanks again, pal. Much appreciated.
simx said:
you are so true, it happens to me all the time, it even answers calls automaticaly, I thought I was pressing some buttons while taking it out of the holster but I tried your little experiment , it was positive all the time,
Now, how to solve this without throwing the holster away?
I notices that it happens more when the screen is facing inside, when I insert it screen outside it rarely happens!
Click to expand...
Click to collapse
U JUST SOLVED MY PROBLEM
I JUST THOUGHT THERE WAS SOMETHING WRONG WITH MY HANDS !!
or what i have is the top button on the right handside to flip between land and port, so when it does that you just press the button and it flips back right away!
Okay, I read that someone lifted part off the front by removing a screen saver! Now with me, I recognized that on the left side bottom, left to where the slideview and call buttons are under, the ENTIRE part seems to come up.
It is lifting itself and I bet in a few days/weeks this will get off.
So my question is if anybody had this happen and knows what is under there? Is there a possibility to GLUE it back on?
Now since I am watching this, I think the ENTIRE front can come off eventually and if it is just glued on at the bottom where one has to press the buttons all the time, it is only a matter of (short!) time until this gets out of hand.
Anybody found anything about taking this phone apart yet?
That happens to my phone, I do not bring it back because I buy it in a duty free shop here it japan and also that is the only issues on my phone and only some bugs. I just press it always there to bring it down but it keeps popping up. I think i can glue it, so I do it to fix the problem. Just be carefull if you do it, I notice that under the plastic screen there are buttons (as I think it is) the hard part that you feel when pressing the slideview or call. When you use a liquid glue and put to much, it can go to that button and worst may stuck that part or go inside the phone and also the part where the mic is. I put glue just on the sides just make sure to put small amount at a time. I cannot give the brand of the glue that I use because its in japanese.Now only the small part in the call buttons is up a little because I cannot put enough glue on that part, but in the slide view button its now okay and working well.
This is my firts post on xda hope it helps a little.
Hey i installed gingerbread android 2.3.7 on my phone again but this time im getting really weak wifi signals... i'm only 5 feet away from router. It was not like this before so i do not know whats going on ( i only dropped my phone twice)
can you guys help me? is it a software issues or hardware?
happy thanksgiving
I would recommend installing a few different roms (that are known to work with wifi) and see if anything changes/improves.
If nothing improves, maybe flash back to winmo 6.5 and see if wifi improves.
If nothing improves then, you may have damaged your wifi antennae when you dropped it then hit up T-mobile!
Best of luck mate.
Possibly knocked the wifi coax loose from the mainboard. It's pretty easy to open up an HD2 and reattach that cable, I've had mine come loose before and that's what I had to do.
I'd definitely try the steps in the above post first just to make sure it's not a rom or kernel specific issue. And if it's still under warranty, don't bother taking it apart and ruining your warranty, obviously just return it to t-Mobile.
hey can you explain in more detail how to push back the wifi coax cable your talking about
Remove the battery cover, battery, sim card, and sd card.
Remove the 4 torx screws that are under little round stickers under the battery cover.
Using an old credit card or a plastic knife, slide between the screen and the housing to release the little plastic clips one by one which hold the housing to the phone's chassis.
Take your time and be careful not to scratch the housing or stick the card/knife in too far, damaging the fragile stuff inside,
It helps to put a little pressure on the back side of the screen wth your thumb while orying with the credit card (back of screen under battery)
The wifi coaxial cable runs from one corner of the mainboard, up along one side of the chassis, is taped together with some other wires, and leads to another small board up near the top of the phone.
Check the connections at both ends, making sure they are connected firmly and are in straight.
You might want to unplug them, just to be sure and hear/feel them click into place.
Take your time, set yourself aside a nice little workspace, and if you are unsure of anything, don't hesitate to come back here and ask.
There is a disassembly video here in the HD2 section somewhere, I think it's in HD2 General. It'd be worth it to search for it and watch at least the first part of the video, just to get an idea what you're dealing with. It's not a very hard job, it should take you like maybe an hour/hour and a half start to finish.
This will void your warranty permanently though.
Thank you sir i just followed the steps you did and it fixed the problem my wifi works fine but now i have another issue....
i dont know if i touched something or disconnected something in the process but my sound, vibration and volume button does not work. External speaker is not playing any sound (no music or key button taps) and no sound is made when placing a phone call BUT the other person on the end can hear me just fine so i'm guessing i might of disconnected like the speaker. ( my assumption)
thanks again for your help
Oh and when a call is being placed or recieved the screen automatically turns off and it becomes non responsive i.e if i take my phone off the ear and want to put it on hold the screen is still black instead of turning back on
The screen going black during a call is a pretty common problem with the HD2, and is likely not related to disassembling your phone as long as the screen functions normally otherwise. Since you didn't take your phone far enough apart to affect the light/proximity sensor, I can't imagine how disassembly would have affected it. You would have to take the mainboard and screen out from the chassis to get to that sensor.
The volume problem on the other hand, is probably due to either your volume rocker not being placed correctly during re-assembly, or the speaker contacts not being aligned properly. You'll have to take it back apart and ivestigate what went wrong.
Try going into Settings/Sound, and checking that the volume is not turned all the way down. If the volume is not all the way down, then you should be able to hear sound, so your speaker is probably not aligned properly.
Does your volume rocker feel different than before? If it doesn't make a definite 'click' when you press it, then it is probably slightly out of place. Also look for any wires that could have been pinched and damaged when you snapped your phone back together.
What is a volume rocker? When i start the phone it usually vibrates once then goes through the starting procoess. Now it doesn't vibrate at all. Phone turns on and i click the volume button up and nothing happens. I checked settings and everything is up
I have the phone opened as we speak and the reciever cable is connected and the vibrator cable is connected too. I tried to use tweezers to see if i can unhook it but their on too tight so thats a good thing. The two orange dots on the volume thing.. the bottom on was slightly off so i put i centered it
Still nothing works. no vibrating no sound ( the person on the other line can hear me but i can't hear anything) but the phone works great.
Im so confused
The volume rocker is the button that 'rocks' back and forth to control the volume.
It has to be positioned right in order to push the contacts that lie beneath it.
Since your phone's apart right now, what happens when you hold the battery in it with one hand, boot it up, and press the volume button contacts manually? If they buttons themselves do nothing, then it must be that they lost their connection somewhere, you'd have to trace the wires and figure out where they're not connected. If they do work, then the volume rocker was just misaligned.
As for the speaker, it has to be that it is not contacting the two little contacts correctly. Look at the speaker and make sure it is sitting correctly in the housing, and look ffor any obstructions near the vibrator motor.
No i can't press down on the volume button ever since i opened it it hasn't fit back right. Doesn't make a click sound
and what contacts on the speaker should i be looking for? are they under the speaker itself? should i remove the speaker? Theres no destruction on the vibrator its looks though like its sitting kinda tight between that camera flash being there..the metal spinning thing on the end of it can spin 360 so nothing its preventing it from moving.
I also can use my headset and the sound and call works fine besides the going to the black screen and not responding. i also noticed my camera does not load up either. but that could probably be solved with a clean install of gingerbread nand rom
I'm hoping somebody with some knowledge of the HD2's innards can help me...
My vibration stopped working on my HD2. I found the plastic LED flash cover to be 'pushed in' (with the help of a couple xda threads I dug up). Others said it was an easy fix: Open the case and push that piece of plastic back into place.
I opened up the case to correct it. But after putting it back together not only does vibrate not work, but the volume keys, speakers (both earpiece and speakerphone), flash, notification led, and camera all don't work.
I obviously screwed something up, but I have no clue what it could have been. I was very careful. One thing I'll note is that when I pulled the case apart, the plastic volume rocker went flying. When putting the phone back together I got it back into place so that I THOUGHT it should work (it was seated properly and felt "clicky" for up/down movements.
But clearly wasn't just the volume rocker that was affected. It doesn't seem that I pulled anything else loose or anything like that...
But no luck, all that I listed above is non functional, and what I'm left with is a glorified 3.5 in tablet
Any ideas?? Thanks in advance!!!
Snapped a couple quick pics which may help:
http://i50.tinypic.com/mmsa36.jpg
http://i47.tinypic.com/sl1kdx.jpg
Unfortunately when comparing these to other pictures of the inside of the HD2 that I found online, I fail to see any differences, or anything I could have inadvertently screwed up.
Most likely you screwed up(or disconnected from motherboard) somehow your main flexboard, but your picture are not usable for this, you should take off your motherboard+main flexboard from chassis to have a full view!
You probobly just disconnected a small cable. I have no idea of the HD2 innards but did multiple repairs of small stuffs and the flat cables hold in place by a plastic clicker pull out easily - just reopen and check them all, you should be fine.
Thanks for the input! I figured it's something like that, just one small cable. But I didn't even take off the board at all... The pictures show the full extent of the disassembly... Do we still think it's necessary to disassemble it further?
I checked all visible connections, but yeah, maybe I somehow yanked out something that is NOT visible. I'll try to check again today... In the meantime, any more ideas from anyone else? Thanks!
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Have u tried starting up the phone without the backing? I had this issue when I painted my housing the led cover was stopping the motor from spinning but if i took out the backing it works. So I just trimmed the led cover and now it works.
Mister B said:
For al that to be not responding I would assume main-flex damaged or as mention before maybe connection to mainboard got moved during pulling cover !
Volume button can be troublesome, sometimes the little plastic caps come off but if it felt clicky should be good in that respect.
also be very carefull of thin spring metal legs that contact antenna pads on back cover, one near screw above & right of vibro motor looks a to be a bit flat. They bend easily & break easily too ...
Click to expand...
Click to collapse
I'm nooby with regard to this stuff; I only attempted the repair since I read in a couple other threads about multiple self-proclaimed non-super-tech savvy people were able to open it up and move the plastic LED cover for an easy fix.
So what exactly am I looking for with regard to the main-flex? Where is it? I thought I wouldn't really see that unless I removed the board which I haven't done... is it still possible I knocked it loose or damaged it? I didn't think that would be possible since I ONLY removed the back cover (though it does take a slightly uncomfortable amount of force to do so, so I guess anything can happen...).
If not the main flex cable, is there anything else specific to look at which may be disconnected? It seems to be all the stuff at the top of the phone that fails to work (camera, speakers, vibration, flash, volume keys). While the stuff on the bottom (other hardware buttons, charging jack, headphone jack, etc).
THanks!
I have given up. After being stumped briefly how to hard reset the device without the volume keys working (I have Android installed), I was able to do it via ADB from the Android dev kit.
To ebay I go...
I just bought an S5 today and I have noticed something that kinda annoys me (I'm upgrading from an S3, and I didn't notice this on that model).
So, what happens is that if I have Touch Sounds [Play sound when making screen selection] enabled, and I have a finger on the back of the phone, somewhere between the speaker and the SAMSUNG logo, every time I make a selection on the screen, the case vibrates and I feel it slightly vibrating under my finger that holds the back of the phone (by the way, I have disabled the haptic feedback, so it's purely due to the sound from the speaker).
My question is: is this a general issue? Does it happen to you?
Sounds like improperly locked cover. Try pressing firmly around the edges of the cover and around the camera area.
It happens to me too. Nothing to worry about.
Sent from my SM-G900T using Tapatalk
It's because waterproof and seals....
The vibration is due to the camera auto focus mechanism. It is completely normal.
Sent from my SAMSUNG-SM-G900A using Tapatalk
I have the S5 Active and when I play music the metal back plate vibrates and (lacking a better way to describe it) makes my finger tips hurt when Im holding it.
I somewhat fixed it by puting a couple apropriately sized pieces of paper inside the back, but this is far from ideal. My idea was to ground the middle of the back plate to the phone. Anyone have any other ideas that might not create a bulge.