Database Users

Is it possible to free the Vista recovery partition?

As title!
Is is possible to delete the Vista recovery partition from hardisk and free the space?

Hi
Have a look at this thread
http://forum.xda-developers.com/showthread.php?t=378890
Should be possible. Remember it looks like it is difficult to get full functionality from an alternative Vista installation so you may not want to destroy this partition unless you have a backup and/or HTC release full downloadable drivers.

Recovery partition
I have used BartPE to boot off an external USB DVD Writer.
From within BartPE you can then use Ghost to capture the ENTIRE drive.
The ***Hidden*** restore partition cannot be see by anything, not ghost, not partition magic, not acronis, it simply is not there.
My belief is that this is due to a BIOS restriction and the FN+F3 boot that does allow the restore is either.....
1. A special mode where the bios can see the hidden partition
2. The actual recovery image is on a separate flash area that we can't see.
Either way having the ghost will recover the hard drive.
I have installed both XP and Linux on the Shift and still been able to reboot, press FN+F3 and do a vista re-installation.
This makes me believe the image is on a separate flash device that only the BIOS section can see.
Hope this helps.
Blitz

blitzspear said:
I have used BartPE to boot off an external USB DVD Writer.
From within BartPE you can then use Ghost to capture the ENTIRE drive.
The ***Hidden*** restore partition cannot be see by anything, not ghost, not partition magic, not acronis, it simply is not there.
My belief is that this is due to a BIOS restriction and the FN+F3 boot that does allow the restore is either.....
1. A special mode where the bios can see the hidden partition
2. The actual recovery image is on a separate flash area that we can't see.
Either way having the ghost will recover the hard drive.
I have installed both XP and Linux on the Shift and still been able to reboot, press FN+F3 and do a vista re-installation.
This makes me believe the image is on a separate flash device that only the BIOS section can see.
Hope this helps.
Blitz
Click to expand...
Click to collapse
Dude my findings are the same, How did you get XP working did you use the vista drivers? did they work? if not where did you get the drivers from? Please tell as I really could do with a dual boot PC

XP.....
Hi there...
I basically tried installing XP SP2 and then XP Tablet Edition.
Both work great, minus a load of drivers.
You have approximately 800MB RAM free and it flies but you lose all the ability to do touch stuff.
There are drivers i've found out there for the sound/graphics/thumbpad and usb network but others i couldn't find.
As to installing XP it's simple, boot off a USB DVD with XP and just install it, format the entire drive (don't worry it won't see or kill the recovery vista partition if it is a partition, still think it's a separate flash card) and install.
As to the dual booting this is not possible.
I halved the drive using Acronis Disk Suite and whilst it would install, i created two PRIMARY partitions and made the second one bootable.
On restarting i installed XP but then i couldn't get VISTA to boot once i made partition one bootable.
Basically to dual boot XP/VISTA you must install XP first, then install VISTA.
However having investigated this I can find most of the additional software / drivers but the VISTA that is restored is a very optimised installation and just installing VISTA Ultimate or even normal Business may not provide the same experience.
Until we can get access to the RESTORE AREA and get at the image (whatever it may be) I think killing the drive completely to reload VISTA won't be possible.
Our only real hope I think is to get HTC to release XP Drivers (I'm still at a loss to explain why they chose VISTA over XP Tablet Edition). The performance increase with XP over VISTA is quite staggering but the loss of functionality makes it pointless at the moment.
Blitz
Whilst it does provide a much faster overall experience at this time without the driver support it's pointless.
Again Linux is the same, I haven't yet tried installing OSX on it, but that would be even more problematic as Apple don't do drivers for most of the hardware out here that XP / VISTA will detect.
I have resorted to going back to VISTA and removing Origami and a few other bits and pieces and updating to SP1.
I find the whole shift now is much better after installing SP1 and without Origami 2.0 on it.
Hope that helps.
Blitz

installing Windows XP alongside Vista
I've used the method described in this link to install XP on my U810 as a dual-boot alongside the pre-installed Vista.
http://www.pro-networks.org/forum/about88231.html
blitzspear, what devices were not working in XP besides the touchscreen?

Missing drivers
Everything was missing,
had to download VGA driver from intel. but you lose some of the resolutions.
There is a sound driver and a USB Network device available and the mousepad worked.
There's a PCI device missing and no SD/wifi and chipset.
So basically not a lot works.
Regards
Blitz

IIRC the Raon Digital Everun has the same SDIO Wifi component. Maybe you could try its driver?
http://www.raondigital.com/data/WLAN Driver_1_1.zip

WiFI driver for VISTA
Hi, dont You have WiFi SD8686 driver for VISTA, please ?
I reinstaled my Shift to localized Vista and this driver I still miss.
more:
http://forum.xda-developers.com/showthread.php?t=376600

Something interesting?

So after flashing the new lollipop update I found myself stuck in a bootloop unable to get into the android operating system at all. I used flashboot and the intel flash tool to try and restore to an older ROM. It forze at 91% with an "error:unable to mount /data" I then used the root tool to try and sideload and install the update.zip from adb shell. No luck. When I rebooted I got to a strange efi menu. Looked around, and it gives me the option to install with with windows?
Anyone have any ideas. I'm waiting for radio shack to open, its the only local place that sells USB otg cables locally.

Here are the photos

njking25 said:
Here are the photos
Click to expand...
Click to collapse
njking25 said:
So after flashing the new lollipop update I found myself stuck in a bootloop unable to get into the android operating system at all. I used flashboot and the intel flash tool to try and restore to an older ROM. It forze at 91% with an "error:unable to mount /data" I then used the root tool to try and sideload and install the update.zip from adb shell. No luck. When I rebooted I got to a strange efi menu. Looked around, and it gives me the option to install with with windows?
Anyone have any ideas. I'm waiting for radio shack to open, its the only local place that sells USB otg cables locally.
Click to expand...
Click to collapse
That is something interesting. It is asking which os to boot to, not install.
I'd like to know how you got into the bios? I am looking for a way to install Linux....
Sent from my YOGA Tablet 2-1050F using Tapatalk

njking25 said:
Here are the photos
Click to expand...
Click to collapse
Did you get this figured out?

I can see "fast boot" enabled. Have You tried to switch it off? any other menu is displayed?
Have You tried to "power+vol down" on it?

I've tried a few ways to get into the BIOS shown... all failed.
Maybe the only way to trigger the BIOS to show is to fully wipe/format the internal storage so the BIOS can't pick up droidboot or anything else. Quite risky though if it isn't the way.
I'm in no way telling anyone to do this and I have not tried it myself. I'd be curious to hear from any advanced users if they have ever completely wiped the internal memory and what options would be available to restore if things did go wrong.

zach181 said:
I've tried a few ways to get into the BIOS shown... all failed.
Maybe the only way to trigger the BIOS to show is to fully wipe/format the internal storage so the BIOS can't pick up droidboot or anything else. Quite risky though if it isn't the way.
I'm in no way telling anyone to do this and I have not tried it myself. I'd be curious to hear from any advanced users if they have ever completely wiped the internal memory and what options would be available to restore if things did go wrong.
Click to expand...
Click to collapse
This guy seems to have stumbled on it also. I flashed the stock kk firmware and I am trying to do it but can't get Lollipop update to work. But it won't boot after it fails so I am reflashing KK again.
http://forum.xda-developers.com/showpost.php?p=60490907&postcount=578

Thanks for the link workdowg,
I'm still trying to work out how they did it. Could do with a step by step and whatever files needed uploaded and linked to. Also the bit about not using windows startup programs.

zach181 said:
Thanks for the link workdowg,
I'm still trying to work out how they did it. Could do with a step by step and whatever files needed uploaded and linked to. Also the bit about not using windows startup programs.
Click to expand...
Click to collapse
If you try it do let me know. I need to get into the bios to get started on a dual boot to Linux on this bad boy...

I will let you know.
I just asked for the OP to clarify a few things before I go ahead. I may try Linux first with Windows 8/10 being the final install.

So... conclusion. we have to damage firmware to boot efi...
If we could swap img file before upload to tab (during this 25 second wait) we could make windows installation possible. Am i right?

zach181 said:
I will let you know.
I just asked for the OP to clarify a few things before I go ahead. I may try Linux first with Windows 8/10 being the final install.
Click to expand...
Click to collapse
@social-design-concepts suggested we should try to change the boot order using efibootmgr. I've been communicating with him. Here is the post in the Venue thread... http://forum.xda-developers.com/show...postcount=2083

Links giving 404

zach181 said:
Links giving 404
Click to expand...
Click to collapse
here it is again... http://forum.xda-developers.com/showpost.php?p=61108700&postcount=2083 it got truncated.

Thanks workdowg.
It seems it's not as clear cut as first thought. Mind you, I didn't expect it to be. I did try a HP keyboard with OTG in Android and that got picked up ok (No lights on keyboard)
I'm a bit in the same mind as Social-Design. I'd rather have a definite way to restore Android from a totally blank internal drive before I have a go. Just up to page 214 in the thread so it may be covered later.

UEFI soft brick?
Hi guys,
I accidentely tried to use the firmware on my 1050 as described in this thread. I can indeed load the UEFI BIOS with all its settings (even though most don't do anything). But unfortunately, I cannot load any OS. I always get the error "EFI Harddrive failed" - meaning it cannot boot fomr hardrive.
I have used an externally powered USB-HUB with mouse, keyboard and USB-Stick and connected to the 1050 via OTG-cable. If the stick is bootabnle with GPT x64 then it will boot from that stick. All 64bit windows versions that I tried failed to install with "ACPI_BIOS_ERROR". 32bit windows would not start, because the GPT is 32bit and the BIOS does not recognise it.
The best success I had so far was to copy a ISO from android-x86 on the usb stick. It will boot in live-mode from the USB. Not so suprisignly, mouse and keyboard are working, touch isn't. WiFI is working and the SD card is detected. I tried to install this version of android on the harddrive which works, but it installs the EFI GRUB bootloader which is not recognised by the BIOS.
I can also access the UEFI shell.
Unfortunately, I am running a bit out of ideas of what to do in order to get a normal system (or firmware) back. ADB-drivers obviously don't work (the Intel SoC driver is installed as well), so I cannot use the Phone Flash Tool.
Any ideas would be greatly appreciated.

Yosha1 said:
Hi guys,
I accidentely tried to use the firmware on my 1050 as described in this thread. I can indeed load the UEFI BIOS with all its settings (even though most don't do anything). But unfortunately, I cannot load any OS. I always get the error "EFI Harddrive failed" - meaning it cannot boot fomr hardrive.
I have used an externally powered USB-HUB with mouse, keyboard and USB-Stick and connected to the 1050 via OTG-cable. If the stick is bootabnle with GPT x64 then it will boot from that stick. All 64bit windows versions that I tried failed to install with "ACPI_BIOS_ERROR". 32bit windows would not start, because the GPT is 32bit and the BIOS does not recognise it.
The best success I had so far was to copy a ISO from android-x86 on the usb stick. It will boot in live-mode from the USB. Not so suprisignly, mouse and keyboard are working, touch isn't. WiFI is working and the SD card is detected. I tried to install this version of android on the harddrive which works, but it installs the EFI GRUB bootloader which is not recognised by the BIOS.
I can also access the UEFI shell.
Unfortunately, I am running a bit out of ideas of what to do in order to get a normal system (or firmware) back. ADB-drivers obviously don't work (the Intel SoC driver is installed as well), so I cannot use the Phone Flash Tool.
Any ideas would be greatly appreciated.
Click to expand...
Click to collapse
You can get it to boot from USB? Get someone with to use tethered twrp and get a backup of the esp and fastboot partitions.
I have 2 things you can try if the goal is getting back to booting stock Android.

Yosha1 said:
The best success I had so far was to copy a ISO from android-x86 on the usb stick. It will boot in live-mode from the USB. Not so suprisignly, mouse and keyboard are working, touch isn't. WiFI is working and the SD card is detected. I tried to install this version of android on the harddrive which works, but it installs the EFI GRUB bootloader which is not recognised by the BIOS.
I can also access the UEFI shell.
Any ideas would be greatly appreciated.
Click to expand...
Click to collapse
Have You tried booting any x64 linux iso from flash drive?

dreamnewbie said:
Have You tried booting any x64 linux iso from flash drive?
Click to expand...
Click to collapse
Thank you for your fast reply.
I just tried that with an Ubuntu Desktop Distro. It boots up from teh USB drive, keyboard and mouse are present. Wifi, sound, touch don't work but I can see the internal Harddrive and the sdcard in the file exsplorer.

Yosha1 said:
Thank you for your fast reply.
I just tried that with an Ubuntu Desktop Distro. It boots up from teh USB drive, keyboard and mouse are present. Wifi, sound, touch don't work but I can see the internal Harddrive and the sdcard in the file exsplorer.
Click to expand...
Click to collapse
extract and dd this to a usb drive and see if it is able to boot it View attachment 3415895 if it successfully boots replace the fastboot.img thats on the thumbrive with one for your devices and see if it boots. if your fastboot.img is named droidboot.img rename it to fastboot.img.
If you can successfully get your devices droidboot/fastboot.img to load you can then disconnect the usb-otg cable and reconnect it to your PC and use the phone flash tools to restore your device completely.

Phoenix OS Single boot

Hello
I'm using Phoenix OS on dual boot with windows but I would like to single boot with Phoenix OS.
Anybody has an idea please
Thanks for attention and sorry, I'm better in french [emoji6]
Fraway

Hello. We are here now.

Phoenix OS [USB]
I have Linux,I've downloaded The iso of PhoenixOS (both version 1.1.3 & 1.2.1),Created a LiveUsb(USB*) installation
But when the installation is done,The USB** won't boot ,The PC skips it and boots from the Hard drive
Idk whether it's a grub error or not
Note:I've tried the grub 2 (Created a partition for it in the USB**),and I've skipped it the second time but the result was the same)
I accepted the Grub Boot loader option Both times
USB* = The Live USB
USB** = The USB where I want Phoenix OS To be installed

I had similar problems with the installation program, however, I solved it by downloading the iso file and "burning" that onto a USB stick with the help of another piece of software cold Rufus.
After that things went well, now writing this on my old HP Probook single booting PhoenixOS.
Hymn said:
I have Linux,I've downloaded The iso of PhoenixOS (both version 1.1.3 & 1.2.1),Created a LiveUsb(USB*) installation
But when the installation is done,The USB** won't boot ,The PC skips it and boots from the Hard drive
Idk whether it's a grub error or not
Note:I've tried the grub 2 (Created a partition for it in the USB**),and I've skipped it the second time but the result was the same)
I accepted the Grub Boot loader option Both times
USB* = The Live USB
USB** = The USB where I want Phoenix OS To be installed
Click to expand...
Click to collapse

treris said:
I had similar problems with the installation program, however, I solved it by downloading the iso file and "burning" that onto a USB stick with the help of another piece of software cold Rufus.
After that things went well, now writing this on my old HP Probook single booting PhoenixOS.
Click to expand...
Click to collapse
Ik Ik
I did the same thing,but when all is done,I get the "No Operating system found" error

Hymn said:
Ik Ik
I did the same thing,but when all is done,I get the "No Operating system found" error
Click to expand...
Click to collapse
By all is done, do you mean after single boot installation onto the hard drive or after installation of the iso onto the usb?
If it's after installation onto the usb, then perhaps you should check whether rufus is formatting the usb to vfat format.
If it's after single boot installation onto the hard drive, had that problem as well, found out that in order for grub2 to work on single boot machines you actually have to make a boot/grub partition next to the normal partition. I was not used to that from other linux installations so I didn't do that as first and got nowhere. After reading somewhere that grub2 needs a separate partition in this case, I reformatted the hard drive in my laptop into two partitions:
sda1: size 350 MB, bootable and vfat -> basically just for grub, the size may be overkill, but on today's hard drives, who cares right?
sda2: size (the rest of the hard drive), ext4 ->all other files and personal data
Then during install use both the grub2 and grub installation option (to sda1) and things should work I think.
Hope this helps!

treris said:
By all is done, do you mean after single boot installation onto the hard drive or after installation of the iso onto the usb?
If it's after installation onto the usb, then perhaps you should check whether rufus is formatting the usb to vfat format.
If it's after single boot installation onto the hard drive, had that problem as well, found out that in order for grub2 to work on single boot machines you actually have to make a boot/grub partition next to the normal partition. I was not used to that from other linux installations so I didn't do that as first and got nowhere. After reading somewhere that grub2 needs a separate partition in this case, I reformatted the hard drive in my laptop into two partitions:
sda1: size 350 MB, bootable and vfat -> basically just for grub, the size may be overkill, but on today's hard drives, who cares right?
sda2: size (the rest of the hard drive), ext4 ->all other files and personal data
Then during install use both the grub2 and grub installation option (to sda1) and things should work I think.
Hope this helps!
Click to expand...
Click to collapse
thanks man it really works!!

Still Missing OS
Hey treris,
First of all, thanks for the excellent info that you've been providing for the single boot Phoenix OS install.
I'm just comfortable enough with computers to get into trouble, but I'm still having an issue with getting Phoenix to boot despite following the steps you indicated. No apparent probs with using rufus. I used Gparted to create 2 partitions on the comp, a 350MB for grub (used manage flags to set it as boot) and the other partition in ext 4. Ran through the install process and while the USB was inserted, no problem, but rebooting without it resulted in the MISSING OS error.
Now, in Gparted I noticed that the 350MB partition (sda20) name is showing as ROOT-B and the ext4 partition (sda23) is named GRUB. As a demonstration of my lack of knowledge in this, it seems that the drive with grub on it should be named grub by the system and not root-b.
Any idea as to where I screwed this up?
Thanks for any help!
treris said:
By all is done, do you mean after single boot installation onto the hard drive or after installation of the iso onto the usb?
If it's after installation onto the usb, then perhaps you should check whether rufus is formatting the usb to vfat format.
If it's after single boot installation onto the hard drive, had that problem as well, found out that in order for grub2 to work on single boot machines you actually have to make a boot/grub partition next to the normal partition. I was not used to that from other linux installations so I didn't do that as first and got nowhere. After reading somewhere that grub2 needs a separate partition in this case, I reformatted the hard drive in my laptop into two partitions:
sda1: size 350 MB, bootable and vfat -> basically just for grub, the size may be overkill, but on today's hard drives, who cares right?
sda2: size (the rest of the hard drive), ext4 ->all other files and personal data
Then during install use both the grub2 and grub installation option (to sda1) and things should work I think.
Hope this helps!
Click to expand...
Click to collapse

Hi SWAMPISH,
It seems like Grub is installed in both partitions, not just in the one dedicated to it. How many partitions do you have in total on that hard drive that you end up with partitions called sda20 and sda23?
My guess would be that somewhere during installation things got mixed up and Grub was installed to the wrong partition meaning it cannot find the boot image. The fact that the partition meant for Grub is now called ROOT and the partition meant for the OS is now GRUB kinda indicates that as well.
I would advise to reinstall PhoenixOS using the installer, you'll wont need gparted for this, and then make sure you reformat both sda20 and sda23 and double check whether Grub goes to sda20 and Phoenix is installed on sda23.
Let me know if this helps.
PS are you installing the current stable version of PhoenixOS (with Android 5.1) or the beta version of PhoenixOS (with Android 7.1)?
SWAMPISH said:
Hey treris,
First of all, thanks for the excellent info that you've been providing for the single boot Phoenix OS install.
I'm just comfortable enough with computers to get into trouble, but I'm still having an issue with getting Phoenix to boot despite following the steps you indicated. No apparent probs with using rufus. I used Gparted to create 2 partitions on the comp, a 350MB for grub (used manage flags to set it as boot) and the other partition in ext 4. Ran through the install process and while the USB was inserted, no problem, but rebooting without it resulted in the MISSING OS error.
Now, in Gparted I noticed that the 350MB partition (sda20) name is showing as ROOT-B and the ext4 partition (sda23) is named GRUB. As a demonstration of my lack of knowledge in this, it seems that the drive with grub on it should be named grub by the system and not root-b.
Any idea as to where I screwed this up?
Thanks for any help!
Click to expand...
Click to collapse

Eureka!
Well, I used the below suggestions and ran into similar issues. So I focused on the partition set up. I removed all partitions, used Gparted to create a partition directory as I BELIEVE that there was an MBR issue. Created 2 partitions (sda1 and sda2 set up exactly as you had indicated in earlier posts), installed both grubs on sda1 and all else on sda2 and BOOM! After installation, removal of USB and restart, got the prompt to run Phoenix OS at startup and it works! I'm so happy!
While frustrating at times, I learned a whole lot more than I bargained for about partitions, booting processes and more!
And Phoenix is so clean and fast on my crappy Aspire One netbook with just 1 GB of RAM!!!
Mega thanks for your help!
treris said:
Hi SWAMPISH,
It seems like Grub is installed in both partitions, not just in the one dedicated to it. How many partitions do you have in total on that hard drive that you end up with partitions called sda20 and sda23?
My guess would be that somewhere during installation things got mixed up and Grub was installed to the wrong partition meaning it cannot find the boot image. The fact that the partition meant for Grub is now called ROOT and the partition meant for the OS is now GRUB kinda indicates that as well.
I would advise to reinstall PhoenixOS using the installer, you'll wont need gparted for this, and then make sure you reformat both sda20 and sda23 and double check whether Grub goes to sda20 and Phoenix is installed on sda23.
Let me know if this helps.
PS are you installing the current stable version of PhoenixOS (with Android 5.1) or the beta version of PhoenixOS (with Android 7.1)?
Click to expand...
Click to collapse

Glad you have it working now! Yes, it's quite amazing how fast old(er) laptops can be when they're using Phoenix OS. They really become useful again.
SWAMPISH said:
Well, I used the below suggestions and ran into similar issues. So I focused on the partition set up. I removed all partitions, used Gparted to create a partition directory as I BELIEVE that there was an MBR issue. Created 2 partitions (sda1 and sda2 set up exactly as you had indicated in earlier posts), installed both grubs on sda1 and all else on sda2 and BOOM! After installation, removal of USB and restart, got the prompt to run Phoenix OS at startup and it works! I'm so happy!
While frustrating at times, I learned a whole lot more than I bargained for about partitions, booting processes and more!
And Phoenix is so clean and fast on my crappy Aspire One netbook with just 1 GB of RAM!!!
Mega thanks for your help!
Click to expand...
Click to collapse

I have been reading through these posts about single boot install. I have tried various ways to install phoenix os. I have a lenovo yoga 900 wiht 16gbs of ram. I tried messing with different partion setups, trying where to install grub and grub 2. everytime I install it after reboot, a blank screen comes up with tGrub on it. Everything runs fine when I run it off a usb flash drive. I am not sure what I am doing wrong. Could someone enlighten me on this?

?
I made the phoneix os installation and the system turned on. However, when the PC is turned off and then back on, the bios screen is turned on and not loaded. I could not understand the problem. (Single boot)

SyriuS1 said:
I made the phoneix os installation and the system turned on. However, when the PC is turned off and then back on, the bios screen is turned on and not loaded. I could not understand the problem. (Single boot)
Click to expand...
Click to collapse
Are you sure you installed Grub correctly? It sounds like Grub may be missing.
Did you set up a separate partition for Grub?

Hello. I'm sorry for possibly taking over an existing thread but this is an install to the hard drive. I should preface and say I'm a noob. I've rooted a few phones and used a few mods on Skyrim (from PC to my PS3). Reading through the thread though I realize how much I am clueless of. So I downloaded from the website, it created a 32gb image and then rebooted. Here my problems are the same as I had with trying (and failing at RemixOS). First if left to it's own devices my laptop will simply not load any OS. It goes to what looks like DOS maybe? However while the _ thingie is blinking it accepts no input. Hard rebooting and going into boot manager, if I touch anything it freezes. Meaning I can't select Phoenix OS from the options. I'm at a loss.
this should be my computer info https://ibb.co/hKsXSv
And this should be the screen i can't get past https://ibb.co/hOM3Za except instead of RemixOS it's Phoenix OS

TgirlValentine said:
Hello. I'm sorry for possibly taking over an existing thread but this is an install to the hard drive. I should preface and say I'm a noob. I've rooted a few phones and used a few mods on Skyrim (from PC to my PS3). Reading through the thread though I realize how much I am clueless of. So I downloaded from the website, it created a 32gb image and then rebooted. Here my problems are the same as I had with trying (and failing at RemixOS). First if left to it's own devices my laptop will simply not load any OS. It goes to what looks like DOS maybe? However while the _ thingie is blinking it accepts no input. Hard rebooting and going into boot manager, if I touch anything it freezes. Meaning I can't select Phoenix OS from the options. I'm at a loss.
this should be my computer info https://ibb.co/hKsXSv
And this should be the screen i can't get past https://ibb.co/hOM3Za except instead of RemixOS it's Phoenix OS
Click to expand...
Click to collapse
Try a USB keyboard, if you have one.

bg260 said:
Try a USB keyboard, if you have one.
Click to expand...
Click to collapse
Check. For a second I thought I had something but alas the boot menu screen freezes with any keystroke... Well tab or the arrow keys...or f6/f5

TgirlValentine said:
Hello. I'm sorry for possibly taking over an existing thread but this is an install to the hard drive. I should preface and say I'm a noob. I've rooted a few phones and used a few mods on Skyrim (from PC to my PS3). Reading through the thread though I realize how much I am clueless of. So I downloaded from the website, it created a 32gb image and then rebooted. Here my problems are the same as I had with trying (and failing at RemixOS). First if left to it's own devices my laptop will simply not load any OS. It goes to what looks like DOS maybe? However while the _ thingie is blinking it accepts no input. Hard rebooting and going into boot manager, if I touch anything it freezes. Meaning I can't select Phoenix OS from the options. I'm at a loss.
Click to expand...
Click to collapse
I found that some machines (especially older ones) won't boot the 64bit version, even though they are 64bit machines, but they will boot the 32bit version.

TNTPro said:
I found that some machines (especially older ones) won't boot the 64bit version, even though they are 64bit machines, but they will boot the 32bit version.
Click to expand...
Click to collapse
I'm pretty sure I've got the 32bit though I suppose it won't hurt to remove what I have and ensure I did indeed click on 32. I'm pretty grated with the whole thing. I'm trying to decide if I blame windows or Compaq lol. I noticed when going through the stuff about my machine that it shipped with Vista. Now I currently have windows 7 but could that be an issue?

TNTPro said:
I found that some machines (especially older ones) won't boot the 64bit version, even though they are 64bit machines, but they will boot the 32bit version.
Click to expand...
Click to collapse
I redownloaded the 32bit version using the downloader tool, saved to hard drive. When I pull up the boot manager after rebooting it still freezes when I press a key. It will still lost windows 7 if I don't touch anything.

Install Android 7.0 Nougat in PC Hard-Drive | Dual-Boot with Windows OS

1. Download Android Nougat 7.0 ISO file[Developed by Android x86].
2. Download Rufus win App to Create Bootable/Live USB.
3. Insert USB with Minimum 4GB and select Downloaded ISO file and finally start.
4. After Finishing, Create New/ Separate Partition in PC for Android to be Installed with Minimum of 16GB Disk Size and Format it as FAT32.
5. After formatting, Reboot PC.
6. Boot PC from USB.
7. Select Install android x86 to HDD.
8. Now In bluescreen Select the Separate Fat32 formatted Partition to Install.
9. Do not Format.( I didn't formatted and it works fine).
10. Install Boot Loader GRUB.( It will replaces default Windows Bootloader).
12. Next it shows up that your are having Windows Partition and asked to create boot item for windows. Select Yes for that else you won't be able to boot into Windows next time.
13. Next Select Skip for EFI GRUB2.(I Skipped and worked for me, I think because I'm having Legacy PC).
14. Then Select Yes to Create Read/Write enabled system directory.
15. Now To create data.img, select yes and then Enter the Size you need for System Memory in MBs (1GB-1024MB).
16. Now Accept Reboot and then Boot Android from GRUB Menu.
17. Thats all . You have Successfully installed Android 7.0 nougat in your PC HDD.
Also I Made Video Tutorial in YouTube for Better Understanding. You can Checkout if you don't understand or if any error pops.
https://www.youtube.com/watch?v=o90aPj4zT-M(TechGeekShan).
Follow Me
http://facebook.com/techgeekshan
http://twitter.com/techgeekshan
https://www.reddit.com/r/TechGeekShan/
http://instagram.com/techgeekshan/
http://www.techgeekshan.in/

Wow thanx mate, will give it a try and will give a feed back.
Sent from my SM-G935F using XDA-Developers mobile app

silverrum said:
Wow thanx mate, will give it a try and will give a feed back.
Sent from my SM-G935F using XDA-Developers mobile app
Click to expand...
Click to collapse
Yeah.. You are welcome and we must Appreciate the Developer who developed Android Nougat x86..

Don't work for me((( Laptop wan't boot after installation...

gmikes said:
Don't work for me((( Laptop wan't boot after installation...
Click to expand...
Click to collapse
Its because of EFI/UEFI Computers

Why not work
Shanmukarajan said:
Its because of EFI/UEFI Computers
Click to expand...
Click to collapse
Why not Work ?

If I install it on my PC, do I access google play store like normal?

successfully installed on Z3735F Bay Trail-T windows 10 tablet. I don't need windows 10 OS anymore, so made one partition and install Android 7. It books OK, WIFI works fine. BUT!!!!! All the physical buttons don't work. Power button doesn't work, so there is no way to turn off the system. Volume Up and Down button also doesn''t work. But touch screen works fine. How to solve this problem? any idea? My tablet is Unbranded Tablet 10.1 from Best Buy

hey,
i got it up & running on my uefi windows 10 lenovo yoga (after some struggle i also have dual-boot). my question - how do i get gapps and supersu? it's not like you could simply flash some zips, as there is no recovery

No Playstore!! Browser does not download files!!!
So after wasting 400mb of data and roughly 30 minutes of my time, I discover that there is no preinstalled PlayStore, the preinstalled browser will not download APKs and trying to install apps from the online MarketPlace only discovers devises that the email used to Sign In with is associated to, not the device this is installed on.
These things SHOULD by all ethical means be stated in the description to prevent others from wasting both their time as well as their data.
I want to see a solution to these problems Shanmukarajan. Should you decide to neglect this issue, I won't hesitate to have this post reported to the moderators.
Thank you in advance for your prompt support on the matter.
Stevo | True.Tech.Tabs
+1 360 **** ***

there is just one issue.
you can not create a data.img file that is larger than 4GB on a fat32 partition...
how do we fix that?

It’s installs fine but when restarts windows is just starting every time and it’s not coming up with step 12 asking me about windows partition and creating boot item

I performed the installation process about 10 times with different settings but none of them seem to install Android on my HDD. The live version works and there are no errors whatsoever, but even after installation there is never an option to boot the installed Android. Only live, debug or again option to install the OS. Does anyone know the solution?
Sent from my Xperia X Compact using XDA Labs

Godecki said:
I performed the installation process about 10 times with different settings but none of them seem to install Android on my HDD. The live version works and there are no errors whatsoever, but even after installation there is never an option to boot the installed Android. Only live, debug or again option to install the OS. Does anyone know the solution?
Sent from my Xperia X Compact using XDA Labs
Click to expand...
Click to collapse
Have you tried selecting yes to GRUB 2 during installation? It's been a little while since I went through the process, but I believe that was what I had to do to get it up and running.

Godecki said:
I performed the installation process about 10 times with different settings but none of them seem to install Android on my HDD. The live version works and there are no errors whatsoever, but even after installation there is never an option to boot the installed Android. Only live, debug or again option to install the OS. Does anyone know the solution?
Click to expand...
Click to collapse
Yeah I have the same issue with my Sony VAIO Duo 11. To start from power off I have to hit the special Duo Assist button, then F11 to boot from usb, then go thru the (re) install every time, so boot takes a couple of minutes, but it always bring me back to the same great working Android with all apps and setting unchanged. I don't understand, but I just happened onto it. Be sure to not format or install any grub (not really sure about grub or grub2), but yes to make it writeable. Then you get an awesomely fast Android.
I don't even want Windows on that machine, but I'm afraid to kill all the partitions and start from scratch as the Duo has some weird builtin Windows boot stuff hard wired. I'm not sure if Android could boot without the Windows partitions.

When I am creating a new partition with 16 GB of space does it mean that Android is going to use just this partition and 16 GB or is it just for the installation files and Android will see my whole HDD as the internal storage?

Could you please let me know how you got it up and running? I am on a UEFI yoga as well, but after the installation,
grub doesn't show up and my computer boots automatically into Windows
Thanks in advance
bombaglad said:
hey,
i got it up & running on my uefi windows 10 lenovo yoga (after some struggle i also have dual-boot). my question - how do i get gapps and supersu? it's not like you could simply flash some zips, as there is no recovery
Click to expand...
Click to collapse

ZOOMA7997 said:
Could you please let me know how you got it up and running? I am on a UEFI yoga as well, but after the installation,
grub doesn't show up and my computer boots automatically into Windows
Thanks in advance
Click to expand...
Click to collapse
Did you change the boot sequence in bios? Select android to boot 1st, then Grub should ask you which os you want to launch. I installed grub 2. I also went with the triple boot. My laptop is an Asus x401a with windows 7. Along with ubuntu and android. x86 Nougat.

A little help here mates,
I installed it alongside a windows 7 ultimate.
Gave it an 80gb Partition (fat32)
So I'm planning a dual boot here.
Here's my Steps:
used rufus to create bootable from android-x86-8.1-r1.iso
booted to Flash drive
installed android to 80gb partition (with grub/windows boot entry/ and data image of 2048MB)
after installation, Reboot to test boot options
grub didn't show up, booted directly to win7
Did some researches, and from those researches I should disable SECURE BOOT, but bios don't have that option.
Also tried EasyUEFI Tool which didn't even work in windows 7
Also, no settings for UEFI or Legacy.
Boot Order doesn't show Windows bootmanager or grub too, only HDD....
I installed android in ASUS Eee Notebook Laptop 1201b
I think the only problem here is grub cant load, but I run out of solutions, so here I am asking for help.

every android on work fine in my tablet(z3735f) but there is a bug in every os no sound in headphone any one tell me how to fix it

How to make a PC Triple Boot Android, Windows 7 and Windows 10

Hi,
How to make a PC Triple Boot Android, Windows 7 and Windows 10?
Thanks

M. Al said:
Hi,
How to make a PC Triple Boot Android, Windows 7 and Windows 10?
Thanks
Click to expand...
Click to collapse
You can use programs like Partition Magic

Maay gaad, I thought this is a tutorial thread

sure u have 3 hard disk with different Operating System (maybe)

Wondering
How it could be done.

zanodor said:
How it could be done.
Click to expand...
Click to collapse
By partitioning your hard drive and then installing each operating system in each partition then use the Grub bootloader software to allow you to choose which of the 3 systems you want to boot when you power on.
https://www.quora.com/Is-it-possible-to-install-Linux-with-Android-and-windows-10-dual-boot-easy-way
Sent from my SM-S767VL using Tapatalk

Hi,
You can also use Virtualbox or other virtualization software to create multiple virtual machine and RUN them on a single machine.
If your computer has good amount of RAM, then you utilize this Virtualbox software. It really works fine. Instead of creating different partition, i think it will be much better option.
Thanks,
Hope it helsp

ziafimawad said:
sure u have 3 hard disk with different Operating System (maybe)
Click to expand...
Click to collapse
I am curious how to do it?

Saenyu67 said:
I am curious how to do it?
Click to expand...
Click to collapse
You can use 1 hard drive or 2 hard drives or 3 hard drives, it works the same regardless of how many you use. It's easily done with just 1 hard drive. If you look at my previous post a few posts back in this thread, you will see a link with instructions to partition your hard drive to create a partition for each of the OS's that you want to install, then you install each operating system in each separate partition that you choose to install them in.
Sent from my SM-S767VL using Tapatalk

How to make a PC Triple Boot Android, Windows 7 and Windows 10
Windows booting is a simple process. You can easily boot your windows 7 OR Windows 10
you can useing some free tools for booting window 10 and windows 7.
I can explained here how to boot a drive easily. I think it will benefit you. For than messege me personally.
Thank you very much.

mdakashhossain said:
Windows booting is a simple process. You can easily boot your windows 7 OR Windows 10
you can useing some free tools for booting window 10 and windows 7.
I can explained here how to boot a drive easily. I think it will benefit you. For than messege me personally.
Thank you very much.
Click to expand...
Click to collapse
You don't understand what they are trying to do.
Sent from my SM-S767VL using Tapatalk

for android, you can use "bluestacks" on windows

So you want to use Windows 10, Windows 7 and Android on PC. For that first create 3 or 4 partitions one for windows 10, one for windows 7 and one for android. Install Windows 10 and Windows 7 on separate partitions and you will see that you have a option to boot into windows 7 or 10. now to install Android use a android based OS such as Prime OS and install it on a separate partition. You can use the pre installed grub or you can use grub2win to get all operating systems that you need

mdakashhossain said:
How to make a PC Triple Boot Android, Windows 7 and Windows 10
Windows booting is a simple process. You can easily boot your windows 7 OR Windows 10
you can useing some free tools for booting window 10 and windows 7.
I can explained here how to boot a drive easily. I think it will benefit you. For than messege me personally.
Thank you very much.
Click to expand...
Click to collapse
Hey there I'm also interested in this I currently have garuda Linux and can't get Windows 10 on

I've done this for a while, my easiest solution is:
1. Make 3 or 4 partitions. Windows 10, windows 7, data partition, and a Linux partition. (There may more created e.g. a system partition). Dont touch the data partition throughout all of this except for storing your OS ISO, liveboot ISO, other program files etc.
2. Install windows 7 on windows 7 partition.
3. Install windows 10 on windows 10 partition. Can be installed from windows 7. Let windows handle making a windows bootloader which can now boot into windows 7 or 10.
4. Create a live USB in ine of your windows. I've been using Ubuntu but used Fedora for years prior. If you aren't sure if you need x64 then go woth the 32 bit x86 architecture (useful to be able to boot on 32 and 64 bit machines). Now boot up your live USB into Linux and install automatically onto Linux partition. You'll now have a GRUB bootloader which can boot into Linux or into your windows bootloader.
5. Install android emulator. I used Linux as I felt I would get better performance emulating android in Linux, this may or may not be true.
There will things that you might find as a nuisance, for example when I boot into windows 7 from windows 10, I need to boot into the GRUB to windows bootloader, select windows 7 and it reboots again back into GRUB and then into windows 7. Not a big deal unless you want to switch OS a lot. If this is the case, you may want to just emulate to begin with. I have a laptop with *ok* processor and RAM, not the best for emulating another OS.
There is many options - you could even install Linux within windows if you so choose. Ultimately the best path will be based on your knowledge, specs of your PC ( power, ram, disk space, disk type [fora mount of partitions], BIOS/UEFI, etc. The method I laid out is the most automated and easiest method I have come up with. Don't try installing windows on top of Linux, you'll cause a headache fixing everything for your Linux system. But then again, everything I've done in Linux the hard way has helped me to understand Linux better. I've just found that even laying out all of the partitions manually for Linux can be challenging, especially if you only have 1 computer and your data is not backed up elsewhere. Start with a blank machine if you can, and have another computer on hand, then you'll have an easy time starting over if necessary. Theres still so many more options of how to do what you are asking... good luck and happy tripple booting

Flash-ARMy said:
I've done this for a while, my easiest solution is:
1. Make 3 or 4 partitions. Windows 10, windows 7, data partition, and a Linux partition. (There may more created e.g. a system partition). Dont touch the data partition throughout all of this except for storing your OS ISO, liveboot ISO, other program files etc.
2. Install windows 7 on windows 7 partition.
3. Install windows 10 on windows 10 partition. Can be installed from windows 7. Let windows handle making a windows bootloader which can now boot into windows 7 or 10.
4. Create a live USB in ine of your windows. I've been using Ubuntu but used Fedora for years prior. If you aren't sure if you need x64 then go woth the 32 bit x86 architecture (useful to be able to boot on 32 and 64 bit machines). Now boot up your live USB into Linux and install automatically onto Linux partition. You'll now have a GRUB bootloader which can boot into Linux or into your windows bootloader.
5. Install android emulator. I used Linux as I felt I would get better performance emulating android in Linux, this may or may not be true.
There will things that you might find as a nuisance, for example when I boot into windows 7 from windows 10, I need to boot into the GRUB to windows bootloader, select windows 7 and it reboots again back into GRUB and then into windows 7. Not a big deal unless you want to switch OS a lot. If this is the case, you may want to just emulate to begin with. I have a laptop with *ok* processor and RAM, not the best for emulating another OS.
There is many options - you could even install Linux within windows if you so choose. Ultimately the best path will be based on your knowledge, specs of your PC ( power, ram, disk space, disk type [fora mount of partitions], BIOS/UEFI, etc. The method I laid out is the most automated and easiest method I have come up with. Don't try installing windows on top of Linux, you'll cause a headache fixing everything for your Linux system. But then again, everything I've done in Linux the hard way has helped me to understand Linux better. I've just found that even laying out all of the partitions manually for Linux can be challenging, especially if you only have 1 computer and your data is not backed up elsewhere. Start with a blank machine if you can, and have another computer on hand, then you'll have an easy time starting over if necessary. Theres still so many more options of how to do what you are asking... good luck and happy tripple booting
Click to expand...
Click to collapse
Yes, exactly what I was indirectly suggesting. I've done it the way you describe before, but, alternatively, you can just create 2 partitions on your hard drive then install Win10 and Win7 in those partitions then create a Linux live USB or even install a full Linux distro on a fairly large USB flashdrive/external hard drive(preferably something that has solid state storage, this enables faster booting and performance and allows installing drivers and packages) and then go into BIOS and set your boot priority to boot from USB first, save changes and exit. Then, when you want to boot Linux you just connect your external drive/USB then reboot the device and it will automatically boot Linux without having to use grub and when the Linux drive isn't connected you will be able to boot 10 and 7 via windows bootloader. A little more round about but makes booting back and forth between operating systems.

Droidriven said:
Yes, exactly what I was indirectly suggesting. I've done it the way you describe before, but, alternatively, you can just create 2 partitions on your hard drive then install Win10 and Win7 in those partitions then create a Linux live USB or even install a full Linux distro on a fairly large USB flashdrive/external hard drive(preferably something that has solid state storage, this enables faster booting and performance and allows installing drivers and packages) and then go into BIOS and set your boot priority to boot from USB first, save changes and exit. Then, when you want to boot Linux you just connect your external drive/USB then reboot the device and it will automatically boot Linux without having to use grub and when the Linux drive isn't connected you will be able to boot 10 and 7 via windows bootloader. A little more round about but makes booting back and forth between operating systems.
Click to expand...
Click to collapse
I had a project to run Windoes 10 on an SD card, which proved to be more difficult than I tbought it would be. I didn't think it should have been difficult, but it seems software amd hard tales measures to prevent this from being possible / "easy". Linux is quite easy to use a live USB, so I've done that quite a bit (I'd keep a 32 bit live USB on my Keychain). I don't think I was ever able to update drivers or install updates to the live USB, however I didn't make much of an effort too. I basically used it as a save my ass tool, which it certainly did come in useful quite often in the course of my personal/school/work computer needs.

Flash-ARMy said:
I had a project to run Windoes 10 on an SD card, which proved to be more difficult than I tbought it would be. I didn't think it should have been difficult, but it seems software amd hard tales measures to prevent this from being possible / "easy". Linux is quite easy to use a live USB, so I've done that quite a bit (I'd keep a 32 bit live USB on my Keychain). I don't think I was ever able to update drivers or install updates to the live USB, however I didn't make much of an effort too. I basically used it as a save my ass tool, which it certainly did come in useful quite often in the course of my personal/school/work computer needs.
Click to expand...
Click to collapse
Instead of installing Linux live on USB, you can do a full installation of Linux on the USB the same as you would when installing Linux on hard drive. A Live USB can be setup with a persist partition to provide a bit of storage on the USB but it isn't enough to do anything with that is useful, that is why it is better to just install the distro on USB instead of using USB to run Linux live.