welcome
rom for upload by SP Flash Tools jumped on the computer message voltage step on usb port. processes at the flash was arrested, after disconnecting the phone from the computer can run it only MIUI logo.
I've installed the drivers and the phone is seen.
Unfortunately, flashing process is interrupted every time before you will show a red progress bar.
I put 2 screens below, depending on the version of the SP Flash Tools
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Related
Hello.
So. I decided that I'm tired of CM and want to come back to stock firmware (the main factor would be the fact that 5.0 is now available in my country) but there is a problem.
I have no problems with accesing my phone through USB cable on my computer but when I started the "downgrade" process through the required program I got an error.
The only reason it doesn't work is most likely this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(It's in Polish - "Cannot find the driver" or something like that)
Any ideas?
Try to install a firmware with qfil the process finishes successfully but at the time of lighting it remains in the logo; I enter when recovering stock and it shows me this error.
Some solution or is a brick?
From already thank you very much
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I need help entering the recovery ive tried grounding key one and two and nothing just keeps boot looping and pc wont recognize the attached device. is there a way to short something on board to force it to enter recovery as im trying to flash a clean rom from manufacturer.
heres a video of the issue
and heres a picture of my board
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I have cheap radio. I tried to upload (from USB key) newest firmware and something wet wrong. Now radio starting, android logo appears, then for 1-2 second status bar is visible and radio restarts. Over and over again... Is possible to go to the root menu or upload firmware in different way? I have something like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
我有个诺威达方案的车机，CPU是高通MSM8917的，被我折腾坏了，我不知道这个机器有没有线刷，论坛里关于这个机器的帖子不多。
这个机器原来是阿里云的系统，我尝试着"root"，但失败了，启动不了系统，停止在LOGO界面。我还拍了一个照片，供大家学习研究。如何能恢复系统？
I have a car machine with a Novada solution, the CPU is Qualcomm MSM8917, it was broken by me, I don't know if this machine has a wire brush method, there are not many posts about this machine in the forum.
The original system is AliyunOS, I tried to "root", but failed, could not start the system, stopped in the LOGO interface. I also took a picture for everyone to study and research.How can I recover the system?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}