Hallo, this is thread for most Sony devices (z1, z2, z3, probably many other too) which use the same eMMC chip, I am sure somebody will need this and I am sure our thread will help in future, I will post tutorial in detail when I collect all needed things for unbricking my dead Z1C! So please do not move this thread, thanks!
Since many Sony devices use KLMAG2GEAC-B001 eMMC chip (???) I starting our thread which will colect all things needed for unbricking device with these chip. Found good document about balls array -> http://www.adata.com/upload/downloadfile/R21-0258_ADATA eMMC 4 5 Series datasheet_20131223.pdf
Since google can not display results for z1c easy jtag emmc pinout scheme, I will need to desolder my chip and locate all needed pins and post picture here.
If you have pinout scheme for emmc unbrick on another xperia phones after z model please post it here!
munjeni said:
Hallo, this is thread for most Sony devices (z1, z2, z3, probably many other too) which use the same eMMC chip, I am sure somebody will need this and I am sure our thread will help in future, I will post tutorial in detail when I collect all needed things for unbricking my dead Z1C! So please do not move this thread, thanks!
Since many Sony devices use KLMAG2GEAC-B001 eMMC chip I starting our thread which will colect all things needed for unbricking device with these chip. Need some small help, Chinese guys if you read this please help here, for colecting pdf documents related to these chip, if you found them post it here please! I have found some download site but I am unable to register since verification code picture is in Chinese language and changing very fast, so if somebody is able to register on these site please download pdf document and post it here! Here is site which need registration http://pdflist.mmic.net.cn/pdf_down/KLMAG2GEAC-B001-pdf_757677_657150716965674566484849.html
Click to expand...
Click to collapse
This partnumber seems to be Samsung eMMC chip, are you sure it is used in Sony device's?
langeveld024 said:
This partnumber seems to be Samsung eMMC chip, are you sure it is used in Sony device's?
Click to expand...
Click to collapse
This one is on my Z1 Compact, I am not sure if it is on 153 or 169 balls array! What you think?
munjeni said:
This one is on my Z1 Compact, I am not sure if it is on 153 or 169 balls array! What you think?
Click to expand...
Click to collapse
I'm not really a pro at this, I've only found datasheets for the JDI/JDC and Sharp screens used in Xperia Z. I came across this thread and started googling.
Will dig into this further later and I'll do my best but I can't really promise anything..
A few things u can try is using Chrome browser with translate function,, or like I did,, writing Sony and the owners of this site u found a mail. Describe what and why u need, that way they provided me the datasheets.. Maybe they will provide those datasheets to u that way I dunno but it's worth trying I think!
I'm really interessted in this topic so i started googleing a bit.
Look on the table on the samsung website: http://www.samsung.com/global/business/semiconductor/product/flash-emmc/catalogue.
There it says something about package:153FBGA.
So I would say the chip has 153 balls
Received Z3X easy jtag + eMMC tool + wires + usb cable...etc + activated and ready for flashing Pinout only remain
problem
Do you brick it with a bad flash? Can the phone not turned on and not loadet?
Does the pc detect the device with qshusb or so?
If yes, i think i could help.
I destroy a sony sp with a wrong image.
Around 10 months iam looking and trying and found a easy solution to unbrick.
So if this is also your problem, write please.
No solution at the moment since I have brick trim area ( http://forum.xda-developers.com/showpost.php?p=56663927&postcount=79 ), so s1tool and gdfs files not helping me, getting error 16 (bad ta). Phone is detected as a bootloader but no way for flashing anything. Will be great if you have a solution!
munjeni said:
No solution at the moment since I have brick trim area ( http://forum.xda-developers.com/showpost.php?p=56663927&postcount=79 ), so s1tool and gdfs files not helping me, getting error 16 (bad ta). Phone is detected as a bootloader but no way for flashing anything. Will be great if you have a solution!
Click to expand...
Click to collapse
I Bricked mine by formatting the first sd partition, sent it to a repair center, they replaced the mainboard, didn't cost me...
Was a rooted z1c with unlucked bootloader, could't flash anything... did'nt try other than with usb connected cable
My phone is up and runing now after changing mainboard. But bad news, I not found all eMMC pins since I broke some of the pins from mainboard during desoldering eMMC ic and was unable to identify some of the pins on mainboard. Found only VCCQ and DAT0 ! Found allso CMD and CLK but I am not sure about order. Only was not found VCC since mainboard is broken . Here is picture, hope somebody find a rest.
Samsung p5220 dead after flash
konsolen said:
Do you brick it with a bad flash? Can the phone not turned on and not loadet?
Does the pc detect the device with qshusb or so?
If yes, i think i could help.
I destroy a sony sp with a wrong image.
Around 10 months iam looking and trying and found a easy solution to unbrick.
So if this is also your problem, write please.
Click to expand...
Click to collapse
DEAR,
i have samsung p5220 LTE phone with unknown base band problem.I write a new certificate.but problem not solved.after i convert this firmware package with octopus box and write it to phone.
AP_P5220XXUBNH2_2412361_REV00_user_low_ship.tar
BL_P5220XXUBNH2_2412361_REV00_user_low_ship.tar
CP_P5220XXUBNH2_2412361_REV00_user_low_ship.tar
CSC_OXA_P5220OXABNH2_2412361_REV00_user_low_ship.t ar
GT-P5220_EUR_XX_20130523
writing log
INFO : 6/15/2015 9:39:44 AM > To connect GT-P5220 phone you have to perform the following steps:
INFO : 6/15/2015 9:39:44 AM > 1. Disconnect USB cable from phone.
INFO : 6/15/2015 9:39:44 AM > 2. Go to Menu->Settings->More->About Device.
INFO : 6/15/2015 9:39:44 AM > 3.Tap on "Build number" 7 times to enable developer options.
INFO : 6/15/2015 9:39:44 AM > 4. Go to Menu->Settings->More->Developer options.
INFO : 6/15/2015 9:39:44 AM > 5. Turn on "USB Debugging" option.
INFO : 6/15/2015 9:39:49 AM > Selected firmware file: AP_P5220XXUBNH2_2412361_REV00_user_low_ship.oct
WARN : 6/15/2015 9:39:52 AM > Please put the phone into Download Mode and connect USB cable.
WARN : 6/15/2015 9:39:52 AM > To put GT-P5220 into Download Mode, You have to perform the following steps:
WARN : 6/15/2015 9:39:52 AM > 1. Reconnect the battery.
WARN : 6/15/2015 9:39:52 AM > 2. Press and hold "Volume-" + "Home" + "Power ON" keys.
WARN : 6/15/2015 9:39:52 AM > 3. When phone turns on, press "Volume+" key.
INFO : 6/15/2015 9:39:52 AM > Found phone on
INFO : 6/15/2015 9:39:52 AM > Firmware write started.
INFO : 6/15/2015 9:39:52 AM > Writing PIT section...
INFO : 6/15/2015 9:39:57 AM > PIT section has been written successfully.
INFO : 6/15/2015 9:39:57 AM > Writing SBOOT section...
INFO : 6/15/2015 9:39:59 AM > SBOOT section has been written successfully.
INFO : 6/15/2015 9:39:59 AM > Writing PARAM section...
INFO : 6/15/2015 9:40:01 AM > PARAM section has been written successfully.
INFO : 6/15/2015 9:40:01 AM > Writing DNX section...
INFO : 6/15/2015 9:40:03 AM > DNX section has been written successfully.
INFO : 6/15/2015 9:40:03 AM > Writing IAFW section...
INFO : 6/15/2015 9:40:05 AM > IAFW section has been written successfully.
INFO : 6/15/2015 9:40:05 AM > Writing BOOT section...
INFO : 6/15/2015 9:40:08 AM > BOOT section has been written successfully.
INFO : 6/15/2015 9:40:08 AM > Writing RECOVERY section...
INFO : 6/15/2015 9:40:10 AM > RECOVERY section has been written successfully.
INFO : 6/15/2015 9:40:10 AM > Writing SYSTEM section...
INFO : 6/15/2015 9:44:06 AM > SYSTEM section has been written successfully.
INFO : 6/15/2015 9:44:06 AM > Writing RADIO section...
INFO : 6/15/2015 9:44:10 AM > RADIO section has been written successfully.
INFO : 6/15/2015 9:44:10 AM > Writing PIT section...
INFO : 6/15/2015 9:44:12 AM > PIT section has been written successfully.
INFO : 6/15/2015 9:44:12 AM > Writing CACHE section...
INFO : 6/15/2015 9:44:17 AM > CACHE section has been written successfully.
INFO : 6/15/2015 9:44:17 AM > Writing HIDDEN section...
INFO : 6/15/2015 9:44:23 AM > HIDDEN section has been written successfully.
INFO : 6/15/2015 9:44:23 AM > Firmware writing successfully completed.
unfortunately..phone was dead.no download mode.when i connect it in to pc (without battery)ONLY show "cloverview" in device manager under other device. please help me to solve this problem
THANK YOU..
Hi guys im having a problem with my xz c6603 it boots to black screen with status bar on stock and hangs on starting apps on cm12.1 I have tried everything. Is my system partition corupt if so how could I fix it.
Related
i'm so sorry but i am going to get crazy if i can't find a solution.
What ever i tried, i could not flash my at&t xperia x10a.
it has stock rom 2.1
i tried flashtool 0.6.9.1
here is the log........................................................................
18/054/2012 00:54:51 - INFO - Connected device : X10
18/054/2012 00:54:51 - INFO - Installed version of busybox : BusyBox v1.19.0 (2011-08-14 23:46:58 CDT) multi-call binary.
18/054/2012 00:54:51 - INFO - Android version : 2.1-update1 / kernel version : 2.6.29
18/054/2012 00:54:52 - INFO - Root Access Allowed
18/055/2012 00:55:18 - INFO - Selected X10a_v2.1.update-1_2.1.A.0.435_Generic.ftf
18/055/2012 00:55:18 - INFO - Preparing files for flashing
18/055/2012 00:55:18 - INFO - Please connect your device into flashmode.
18/055/2012 00:55:20 - INFO - Device disconnected
18/055/2012 00:55:40 - INFO - Device connected in flash mode
18/055/2012 00:55:40 - INFO - Opening device for R/W
18/055/2012 00:55:40 - INFO - Reading device information
18/055/2012 00:55:40 - INFO - Phone ready for flashmode operations.
18/055/2012 00:55:40 - INFO - Start Flashing
18/055/2012 00:55:40 - INFO - Flashing loader
18/055/2012 00:55:44 - INFO - Loader : S1_Loader_Root_f851 - Version : R4A024 / Bootloader status : ROOTED
18/055/2012 00:55:44 - INFO - Ending flash session
18/055/2012 00:55:44 - INFO - Flashing finished.
18/055/2012 00:55:44 - INFO - Please wait. Phone will reboot
18/055/2012 00:55:44 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
18/055/2012 00:55:44 - INFO - Device connected in flash mode
18/055/2012 00:55:45 - INFO - Device disconnected
...........................................................................................
at&t prevented phone from unknown sources therefore, i can't flash it.
any suggestions ?
Shouldn't matter if you have unknown sources checked. Did you enable usb debugging?
Sent from a galaxy far, far away...
you can flash your phone no matter what just make sure to connect properly(in flash mode..pull out battery. Put back in.hold back button while powered of and plug in USB while doing so
Edit: what are you trying to do exactly?
Sent from my X10i using XDA
18/055/2012 00:55:44 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
Agree check debugging
settings/applications/development
From XDA on my XPERIA X10-S, powered by DooMKerneL
usb debugging is on...
i noticed that flash tool does not show firmware content ??? can it be the reason ?
1) i run flashtool.
2) connect phone to pc by usb
3) i click to flash button and proper rom
4) flashtool want me to plug off the usb and turn the phone off.
5) i do as it says. turning off, pulling battery out. putting it back. holding the back button while connetcing usb. green light appears.
6) as a result it reboot the phone everytime i try to flash.
ohhh at last.
guys... believe in searching . in xda forums, i found some guys with same problem. i mentioned the solution below.
i finally noticed that ftool does not see firmware content. The reason is surprising. I am in Turkey and location and language in windows 7 are stated as Turkish and Turkey. By changing them to USA and English, flashtool started to see content and now i did it.
thank you everybody for your attention.
so i bought my set second handed d802 but when i checked its imei no it showed 15 digit no and then i checked it in
different sites to see what firmware i was using ...
https://imeidata.net/warranty/lg
when i checked it showed nothing there .... no result
when i try to update it showed "NOT REGISTERED YET"
i thought it was an faulty imei no
so i popped up the back cover and check the printed imei no on the back side ......
YEAH IT WAS DIFFERENT
i check that imei no ..in the website showed the right model
then i used the following method to change my imei number
I found this some where here in XDA which was triggered to restore imei no . I
used this to change my imei thanks who wrote those steps ...made some changes too
Make sure your LG G2 is running the stock LG firmware. If your phone does not have official firmware installed on it, restore it to stock first.
Install the latest LG USB drivers on your computer: link is given below the thread
Now download the IMEI converter tool and unzip it: link is given below the thread
Download QPST (Qualcomm Product Support Tools) and unzip it: link is given below the thread
Open the QPST_2.7_378 and run the setup file to install it on your computer.
Enable USB debugging on your LG G2. You can find this option under Settings> Developer options. To enable Developer options on your device, follow the instructions given here.
Connect your device to the computer. And put it on PC suit mode note : port doesnot appear if it is in mtp pr ptp modes
Run QPST configuration and click on Ports tab. Click on Add new port option.
Your current port should show as COM4/5.
Select the port and click OK. The port should come up on active phones.
Select the phone and click the Software Download option from Start clients menu.
Now click on Backup tab. You should see your phone’s port.
Click on Start to initiate backup.
Now navigate to C:/ Program Files/ qualcomm/ qpst/bin folder.
Run RF_NV_Manager.
Click File> Read from phone. Your phone’s IMEI number should appear on number 550; NV_IMEI_I *the worng imei *
Click on item 550. You would see 9 fileds with the hex codes *wrong hex code or imei hex code*
Now run IMEI Converter.exe.
Now type your phone’s IMEI (which was in your back cover )in Enter IMEI field.
Then click on <Convert IMEI> button.
You should see 18 digits in groups of 9. *hex*
In RF_NV_Manager program, click on Hex by Write NV button.
In the 9 boxes, edit the numbers from IMEI converter starting from left to right . Type in first group of two numbers in the first field, then go to the next field and type in second 2 digits.
When you are done with doing this, click on Write NV option.
Then click File> Read from phone.
Item number 550 should appear now.
Disconnect the USB cable and reboot it.
Open phone’s dialer and dial *#06#. You should see your phone’s IMEI now.
Now check updates
credit goes to the one who wrote this orginally
links
check imei here--> https://imeidata.net/warranty/lg
get lg usb driver ---> http://g2-lg.com/download-lg-g2-android-usb-drivers-ver-3-10/
https://drive.google.com/folderview?id=0B_NvFkRRo5RxREZoRmg5VTVsek0&usp=sharing
# copy rights to the author's
#sharing is caring
#thankyou
Thanks for sharing! Will help someone in need
IMEI converter is specified as virus in Google drive. Any other link
caldent said:
IMEI converter is specified as virus in Google drive. Any other link
Click to expand...
Click to collapse
I have a LS980, I have successfully restore IMEI but other values luke MEID, MIN Dex Hex are still unknown or Wrong.
And in Network. Info "Service disabled" showed.
axeronb said:
so i bought my set second handed d802 but when i checked its imei no it showed 15 digit no and then i checked it in
different sites to see what firmware i was using ...
https://imeidata.net/warranty/lg
when i checked it showed nothing there .... no result
when i try to update it showed "NOT REGISTERED YET"
i thought it was an faulty imei no
so i popped up the back cover and check the printed imei no on the back side ......
YEAH IT WAS DIFFERENT
i check that imei no ..in the website showed the right model
then i used the following method to change my imei number
I found this some where here in XDA which was triggered to restore imei no . I
used this to change my imei thanks who wrote those steps ...made some changes too
Make sure your LG G2 is running the stock LG firmware. If your phone does not have official firmware installed on it, restore it to stock first.
Install the latest LG USB drivers on your computer: link is given below the thread
Now download the IMEI converter tool and unzip it: link is given below the thread
Download QPST (Qualcomm Product Support Tools) and unzip it: link is given below the thread
Open the QPST_2.7_378 and run the setup file to install it on your computer.
Enable USB debugging on your LG G2. You can find this option under Settings> Developer options. To enable Developer options on your device, follow the instructions given here.
Connect your device to the computer. And put it on PC suit mode note : port doesnot appear if it is in mtp pr ptp modes
Run QPST configuration and click on Ports tab. Click on Add new port option.
Your current port should show as COM4/5.
Select the port and click OK. The port should come up on active phones.
Select the phone and click the Software Download option from Start clients menu.
Now click on Backup tab. You should see your phone’s port.
Click on Start to initiate backup.
Now navigate to C:/ Program Files/ qualcomm/ qpst/bin folder.
Run RF_NV_Manager.
Click File> Read from phone. Your phone’s IMEI number should appear on number 550; NV_IMEI_I *the worng imei *
Click on item 550. You would see 9 fileds with the hex codes *wrong hex code or imei hex code*
Now run IMEI Converter.exe.
Now type your phone’s IMEI (which was in your back cover )in Enter IMEI field.
Then click on <Convert IMEI> button.
You should see 18 digits in groups of 9. *hex*
In RF_NV_Manager program, click on Hex by Write NV button.
In the 9 boxes, edit the numbers from IMEI converter starting from left to right . Type in first group of two numbers in the first field, then go to the next field and type in second 2 digits.
When you are done with doing this, click on Write NV option.
Then click File> Read from phone.
Item number 550 should appear now.
Disconnect the USB cable and reboot it.
Open phone’s dialer and dial *#06#. You should see your phone’s IMEI now.
Now check updates
credit goes to the one who wrote this orginally
Click to expand...
Click to collapse
Was your phone rooted ?
[ Guide to unbrick your Hard bricked MOTO G (Falcon) xt1033 from "QHSUSB_BULK" ]
Hello everyone , today I will show you how to unbrick your device from HardBrick (No power up, no charging or any sign of life after updating to Lolipop ) ...
This is tutorijal just for Motorola G (Falcon) model xt1033 !
For xt1032 steps is the same but just with another firmware I will put the link in down section ...
Preparing ^_^
- Download 7-zip :
for 32 bit user :
https://www.7-zip.org/a/7z1805.exe
for 64bit user:
https://www.7-zip.org/a/7z1805-x64.exe
-Next download "Unbrick Mogo G X1033" files for X1033 model:
https://drive.google.com/file/d/0B8moFi11OJMUWWpVbjhNOGNpSGs/view let me know if the link has expired
So let's begin ^_^ ....
1. Extract "Unbrick Mogo G X1033" files on Desktop using 7-Zip archive tool.
2.Once you extracted install "MotorolaDeviceManager_2.5.4" manager in order to install MOTOROLA USB driver
3. Open "Riff BOX JTAG Drivers" see picture ...
https://ibb.co/NVNCXVw
* and Run "dseo13b" see picture ...
https://ibb.co/n7ppnPP
* click on "Next" -||- ...
https://ibb.co/LR46t9Q
* click on "Yes" -||-
https://ibb.co/YPVc0gJ
*check "Sign a System File" and click on "Next" -||-
https://ibb.co/2vy46NP
Now copy qcusbser.sys driver path and past it inside "dseo13b bar" see pictures ...
a) https://ibb.co/g70XxGD
b) https://ibb.co/RTyXXGb
c) https://ibb.co/b1q6Fv6
d) https://ibb.co/GxvgZvh
4. Now Reboot your PC and disable "Driver signature Envelopment"
* For Windows 7 Users:
https://www.youtube.com/watch?v=Z_ouuX14anY
* For Windows 10 Users:
https://www.youtube.com/watch?v=71YAIw7_-kg
5. Now plug your device with USB cable and manualy install "QLoader driver" , to do that Open Computer Manager , click on "Device Manager" , then click on "QHUSB_BULK" .... see Pictures
a) https://ibb.co/xfnr34B
b) https://ibb.co/HCq07QW
c) https://ibb.co/JpyQSTv
d) https://ibb.co/sK4NPsN
e) https://ibb.co/b2BcVVP
f) https://ibb.co/8x9m2hR
h) https://ibb.co/1Xv5qkm
i) https://ibb.co/qW54nj4
j) https://ibb.co/rv8yZnF
k) https://ibb.co/fdcCbSr
l) https://ibb.co/C93fqWZ
6. Once the driver is installed , open "Blank flash by DuplaDeUmSo" and run "blank-flash" it should look like in the pictures ...
a) https://ibb.co/Wt52yrz
b) https://ibb.co/nnTNyh2
c) https://ibb.co/6ZjTRq0
* Now your phone it should be into FastBoot flash mode , make sure that baterry status is OKAY if it's low put your phone in charge for about 1 or 2 hours in order to have fully charged battery !
d)https://ibb.co/nn673Tr
7. Now open "mfastboot v2" and run "flash 5.1" bat file in order to flash stock firmware inside your device see picture ...
a) https://ibb.co/pXxby5G
b) https://ibb.co/3pR2kPy
c) https://ibb.co/7pfg52X
Now your device will reboot and boot normally ....
For "X1032" users :
https://www.youtube.com/watch?reload=9&v=bRtWQRmjEbM
If this tutorijal has help you, you can pay any amount if you want to this guy who tested on his device and shared his experience on one Spanish forum ...
paypal.me: paypal.me/DuplaDeUmSo
Hello, can step number 1-6 in this guide applied on another hardbricked device?
Thanks.
namakosong said:
Hello, can step number 1-6 in this guide applied on another hardbricked device?
Thanks.
Click to expand...
Click to collapse
Hi, which device?
Teddy Lo said:
Hi, which device?
Click to expand...
Click to collapse
Sony Xperia XZ Premium
No! This is only for Moto G devices....
Explain what kind of problem you have on your device?
Qhsusb_bulk when connect to pc. Wanna try to flash via qpst but i can't find the prog_emmc_firehouse file for my device. Can you help me, please?
Follow this tuttorial:
If you are facing problem with first tool try with this one:
Teddy Lo said:
Follow this tuttorial:
If you are facing problem with first tool try with this one:
Click to expand...
Click to collapse
Thanks, i will try it..
Teddy Lo said:
Follow this tuttorial:
If you are facing problem with first tool try with this one:
Click to expand...
Click to collapse
I have facing another problem. When i press the volume down button nothing happen. The green led light doesn't show. Any solution, please?
Make sure that your usb port is clean also try with other usb cable, if that doesn't work maybe your battery is problem or some hardware issue like ic chip...
Teddy Lo said:
Make sure that your usb port is clean also try with other usb cable, if that doesn't work maybe your battery is problem or some hardware issue like ic chip...
Click to expand...
Click to collapse
I will try it again. Thanks for your advice
ROM / Firmware/ Brick Recovery for 7" Android Head Unit AC8227l YT9217 YT9218 1/16GB
Thanks everyone who contributed in my effort to fix my bricked device. Here is all that I have found useful in successfully reviving my device.
The files shared here are the ones that worked on my unit (see specs and pictures below) If your device is different, it may or may not work.
If the device has dedicated radio chip inside, the Firmware number will show as YT9218, if no radio chip, then it will show as YT9217
Note: if your device is not bricked, Make a full backup before trying another firmware.
I hope it helps. (donations are always welcome )
Memory dump:
firmware 20181222 HiFi: (Link) (thanks mazepa2000) (May 2019 update below)
Rooted TWRP firmware 20190523 HiFi: (Link)
Preloader (Boot_1) from other Similar Firmwares: (Link) <- Click again if it doesn't lead to the relevant post.
Download the one similar to your device's version.
Firmware via flash tool: Rooted TWRP 20190523 (Link) Thanks Maxkir
(You may need to remap side touch buttons in Factory settings (code 8888) -> Touch settings -> Click start -> Name of the button -> The button itself ->Repeat for all the buttons -> close -> ok).
Firmware for YT9213 Device: (Link) (Thanks pajurpl)
Update / Upgrade Files USB flash drive:
Firmware 20190522 HiFi: (Link) (Thanks foxgiggle , iSevenAuto)
Firmware 20190906: (Link)
MCU 3.1 (Link)(Thanks foxgiggle )
MCU 2.8 (Link) (Thanks lemmon and foxgiggle)
I hope it helps. (donations are always welcome )
Memory Dump Procedure via flashtool:
(Memory dump is only needed if you need full recovery from a backup. Otherwise you may only need to do the next part.)
Download and install MTK drivers. (Link)
Load scatter file and preloader (Link) in spflashtool. Press Ctrl Alt V , then go to Window and select "write memory". In file path select "user", in begin address put 0x0, In Region select the partition named "EMMC_USER". Hit Write memory. After that plug in the usb cable (connected to usb1 port). If the device is not detected, you need to power it on. If still not detected then you might need to short the two test points (see picture) (without power this time) and then plug in the usb cable. Remove the short when write process starts. Check if the issue is fixed. If its not fixed, then do the same to write boot2 and boot1 partitions as well. You may need to download Boot_1 specific to your original firmware from the link above.
Uploading Firmware (full or parts) via flashtool:
If you are uploading the firmware available in parts, you only need to upload "BOOTIMG" and "ANDROID" (SYSTEM).
You may also need to flash "RECOVERY". Remember to uncheck the preloader. Here is a nice instructions file. (Link) (thanks Maxkir)
There is more info and firmwares to chose from at 4pda forum.
Update / Upgrade Procedure via USB flash drive:
Copy the zip file (do not extract) to usb drive or microSD card, (formatted by SD Card Formatter). Connect to usb port 1 or 2. Go to Car Settings, System info. Click Android Upgrade.
--OR--
Extract the zip into a folder named XYAUTOUPG into the flash drive or microSD card, connect to usb port 1 or 2 and then reboot. Upgrade should start automatically. You might need to try with different USB drives or sd cards. For some reason this only works with certain usb and cards.
I hope it helps. (donations are always welcome )
MCU Upgrade Procedure via USB flash drive:
Extract the mcu file into flash drive or microSD card. Connect to usb port 1 or 2. Go into system info and update mcu.
Make a Full Backup/Memory Dump:
Open SPFlashtool, Select Memory Test Tab, Select only RAM Test (uncheck the rest), push start, and connect the unit. Save the information appeared, in a text file for later. (Read above "Memory dump procedure" for the usb connection setup).
Now go to ReadBack Tab, Double click on empty space next to tick mark, Select a folder where you want to store the dump file, and Type a name for the dump file you are going to creat, (ie. Boot_1, Boot_2, USER). Click Save. In next window "Readback block start address", select the region you want to make backup of (ie. EMMC_BOOT_1, EMMC_BOOT_2, EMMC_USER).
Start address is 0x0000000000000000
Length copy and paste from the text file you created earlier.
typically for Boot_1 and 2 the length is 0x0000000000400000
and for USER (16GB models) the length is 0x00000003a8000000
Click OK.
Now click on Readback and then connect the unit via usb cable. and Read process will start.
Do the same to make backup of all three partions. USER will take long time because its the largest partition.
RDS FM Radio:
Radio app with fixed RDS, channel names on buttons and HiFi: (Link) (thanks sjguk)
Copy to FMRadio directory /system/priv-app/FMRadio, rename to FMRadio.apk and change permission 764. (or 755 ?).
Channel name Editor: (Link) (thanks mclaught)
install as normal. You may need to install GalaPublicResources. Click top right dots.
I hope it helps. (donations are always welcome )
Multi Window Mode:
Go to root folder, look for build.prop. Open in text editor. Change the line ro.build.type=user to ro.build.type=userdebug.
If no such line is there, then simply add the line at the end. Save and exit. Go to Android settings, Developer options, look for multi window mode and enable it. Swipe down from the top of the window, Click on recent apps tile. You'll see the new multi window option there.
Subwoofer output Pin:
The default AUX_out pins are for mid range audio and is controlled by Mid slider in the mixer. The subwoofer output is on another pin (See Picture).
it is easy to remove one of the AUX_out pin and install it at the Sub output. this pin is controlled by Subw slider in the audio mixer.
Launchers UI1, UI2, UI4, UI5 (Link) (Thanks Maxkir)
Boot animation: (Resolution is 1024x600)
eg. (Link)
The animation preview didn't work for me, but I installed it anyway and it worked fine.
OBD Dongle Bluetooth Setting:
Open Bluetooth app, Click on settings, tap on the pin code "0000" and type in "1234" instead. Save settings.
Now search and connect the OBD dongle normally.
I hope it helps. (donations are always welcome )
Unit Specs:
motherboard marking YT9217 VER1.5 XY AUTO also 9218 VER2.4 XY AUTO near the antenna
Model no 8227L_demo android 8.1
Android YT9217C_00005_V003_20191402_HIFI
Kernel 3.18.22
DDR 1GB FLASH 16GB
CPU A7 1.3GHzx4
Amplifier AC7315 mos bile duct 45Wx4
AutoChip ARM AC8227L
Mediatek MT6323LGA
Kingston EMMC 16G
Im looking for the same ROM. Let me know if you find some info. Also Im looking for the AirRadio App. so I can use a Launcher.
Thanks
viktorsaari said:
the link takes me to the main page. and then its like finding needle in a haystack.
Click to expand...
Click to collapse
All relevant info about ROMs and flashing you can find in top header of this russian forum.
Look at the spoilers in the gray header layer and use Google translate to understand what is written there.
There are 3 ROM versions for the 8227L based head units. I downloaded and installed the oldest of the 3 (rooted and TWRP IMG included). Copy all files from the RAR to a flashdrive in root folder.
Turn off the head unit.
Connect the flashdrive to USB 1 slot of the head unit.
Turn on the the head unit.
The install process starts immediately after turning on.
It takes about 10 minutes.
When install process is ready, turn off the head unit.
Detach the flashdrive.
Turn on the head unit and it will boot with factory settings like a new device....
Note that there are also ROMs for flashing wit MTC flash tool downloadable.
But the versions for installing from USB sticks ( po russki - dla flashky) are more comfortable to install and I don't own a Windows pc. So this variant was my favorite method...
Regards and good luck...
Edit: if your unRAR program asks for a password for unpacking the RAR file, then use Eazy unRAR app from Playstore on your Android device - it ignores password lock in RAR file ...
Edit2: the 5th gray spoiler in the top header of the Russian forum hosts the links to the ROM RAR files...
The USB flash drive method didn't work for me, Device doesn't detect USB while booting up. I tried everything, connecting the test points, pushing reset button etc. to no avail.
SP flash tool does seem to work, I have tried uploading several available roms, only these three uploaded successfully,
full_8227L_demo-userdebug 6.0 MRA58K 1534513814 test-keys
Заводская прошивка под флештул от 09.11.2018 UI1 с переводом
20181224 TWRP ROOT перевод и эквалайзер от ноябрьской
but didn't turn on the device. Device turns on but I get a black (backlit) screen. What else is there to try?
bitstra said:
All relevant info about ROMs and flashing you can find in top header of this russian forum.
Look at the spoilers in the gray header layer and use Google translate to understand what is written there.
There are 3 ROM versions for the 8227L based head units. I downloaded and installed the oldest of the 3 (rooted and TWRP IMG included). Copy all files from the RAR to a flashdrive in root folder.
Turn off the head unit.
Connect the flashdrive to USB 1 slot of the head unit.
Turn on the the head unit.
The install process starts immediately after turning on.
It takes about 10 minutes.
When install process is ready, turn off the head unit.
Detach the flashdrive.
Turn on the head unit and it will boot with factory settings like a new device....
Note that there are also ROMs for flashing wit MTC flash tool downloadable.
But the versions for installing from USB sticks ( po russki - dla flashky) are more comfortable to install and I don't own a Windows pc. So this variant was my favorite method...
Regards and good luck...
Edit: if your unRAR program asks for a password for unpacking the RAR file, then use Eazy unRAR app from Playstore on your Android device - it ignores password lock in RAR file ...
Edit2: the 5th gray spoiler in the top header of the Russian forum hosts the links to the ROM RAR files...
Click to expand...
Click to collapse
No idea, what else you can try
If you can connect a PC to headunit and flashed a ROM with TWRP, may be you can use adb reboot recovery and clear data and cache via TWRP?
Hope you find a solution to boot your HU...
viktorsaari said:
The USB flash drive method didn't work for me, Device doesn't detect USB while booting up. I tried everything, connecting the test points, pushing reset button etc. to no avail.
SP flash tool does seem to work, I have tried uploading several available roms, only these three uploaded successfully,
full_8227L_demo-userdebug 6.0 MRA58K 1534513814 test-keys
Заводская прошивка под флештул от 09.11.2018 UI1 с переводом
20181224 TWRP ROOT перевод и эквалайзер от ноябрьской
but didn't turn on the device. Device turns on but I get a black (backlit) screen. What else is there to try?
Click to expand...
Click to collapse
No luck with adb either.
seems like my only option is if I could get the exact ROM for this device and flash it. The seller was less than helpful, so Aliexpress refunded me in full.
bitstra said:
No idea, what else you can try
If you can connect a PC to headunit and flashed a ROM with TWRP, may be you can use adb reboot recovery and clear data and cache via TWRP?
Hope you find a solution to boot your HU...
Click to expand...
Click to collapse
Received firmware files from seller, but its probably the update files, not the complete firmware. Unable to flash it via sp flash tool. (copy and paste the whole link until the .zip part)
http://download.seicane.com/doc/80/H5 Android 8.1 updated file.zip
Any ideas ???? my device is a brick at the moment, and doesn't recognise usb flash drive for updating.
Fixed.:victory:
Check the first post for detail.
So you flashed via sd card or flashtool?
viktorsaari said:
Fixed.:victory:
Click to expand...
Click to collapse
Hi How did you manage to fix it I have the same problem?
---------- Post added at 03:47 PM ---------- Previous post was at 03:46 PM ----------
viktorsaari said:
Received firmware files from seller, but its probably the update files, not the complete firmware.
http://download.seicane.com/doc/80/H5 Android 8.1 updated file.zip
Any ideas ???? my device is a brick at the moment, and doesn't recognise usb flash drive for updating.
Click to expand...
Click to collapse
The link is dead!
SP Flash tool.
ric69 said:
So you flashed via sd card or flashtool?
Click to expand...
Click to collapse
Thanks but flashtool is impossible to me as I don't have any USB recognition on my pc
Please see the original post, I added the things I did to fix it.
the link is not dead, copy and paste complete until the .zip part
anyway this zip file didn't help.
Check the first post for helpful material.
coffer said:
Hi How did you manage to fix it I have the same problem?
---------- Post added at 03:47 PM ---------- Previous post was at 03:46 PM ----------
The link is dead!
Click to expand...
Click to collapse
ric69 said:
Thanks but flashtool is impossible to me as I don't have any USB recognition on my pc
Click to expand...
Click to collapse
Did you get your connection to the PC yet?
---------- Post added at 03:28 PM ---------- Previous post was at 03:25 PM ----------
viktorsaari said:
Please see the original post, I added the things I did to fix it.
the link is not dead, copy and paste complete until the .zip part
anyway this zip file didn't help.
Check the first post for helpful material.
Click to expand...
Click to collapse
Thanks for that, wow the memory dump is massive more than 4Gb! Did you use format and download or just download in the Flash tool? Do you know the files the scatter file took from the memory dump? So, you didn't use any files from the first download where you took the scatter file from? I'm still having a problem connecting to my PC may have to use the hardware forced (testpoint) method!
You need usb male to male cable, attach it to usb1 on the device. but not yet connect to pc. Run the sp flash tool. and select the correct scatter file. Then run which ever function you need. after that connect the usb cable to pc while connecting these two test points (picture) with a small piece of wire to each other. After it is recognised and operation starts, you can release the jumper wire.
ric69 said:
Thanks but flashtool is impossible to me as I don't have any USB recognition on my pc
Click to expand...
Click to collapse
viktorsaari said:
You need usb male to male cable, attach it to usb1 on the device. but not yet connect to pc. Run the sp flash tool. and select the correct scatter file. Then run which ever function you need. after that connect the usb cable to pc while connecting these two test points (picture) with a small piece of wire to each other. After it is recognised and operation starts, you can release the jumper wire.
View attachment 4769616
Click to expand...
Click to collapse
Thanks, when I use the scatter file from the first download and put it with the files in the second download it only picks up the preloader file nothing else?
Hi, Scatter file is only needed to make sp flash tool recognise the partition table on the device. no need to download anything via scatter file. press Ctrl Alt V , then go to Window and select "write memory". Set start address to 0x00 Use this to write Boot_1 , Boot_2 and User, to EMMC_Boot_1, EMMC_Boot_2 and EMMC_User respectivly. thats it.
I hope it helps.
Thanks for that, wow the memory dump is massive more than 4Gb! Did you use format and download or just download in the Flash tool? Do you know the files the scatter file took from the memory dump? So, you didn't use any files from the first download where you took the scatter file from? I'm still having a problem connecting to my PC may have to use the hardware forced (testpoint) method!
Click to expand...
Click to collapse
Hi, yes, I fixed it. Check the first post for details.
NicoApple said:
Im looking for the same ROM. Let me know if you find some info. Also Im looking for the AirRadio App. so I can use a Launcher.
Thanks
Click to expand...
Click to collapse
Thanks but for most of us , we don't have any USB recognition to pc (or android devices) there is any sounds when plug
ric69 said:
Thanks but for most of us , we don't have any USB recognition to pc (or android devices) there is any sounds when plug
Click to expand...
Click to collapse
have you tried the test point method yet, I will try it tomorrow or Monday?
This thread is consolidating all the information of Junsun V1 and V1Pro devices scattered in the Android Head-Units forum. I want to write and extend this to make it easier for new people. It's sometimes difficult to find the right information.
Warning: Some of these commands are altering the system. If something goes wrong you can brick your device. Be sure you know what you're doing. I'm not responsible for any damages!
General Other ThreadsJunsun V1Junsun V1 ProJunsun V1 Pro Firmware (8259)Junsun V1 Pro Firmware (8227L)Junsun V1 (8667Q)FirmwareUpdating the device firmwareJunsun V1 Pro firmware filesRootADB connectionRoot with MagiskWritable System
Updating FirmwarePreparation
USB drive formatted as FAT32
Files for update (*.bin, *.upd) need to be in the root directory of the USB drive
Starting the UpdateThe update should start automatically when the USB drive is plugged in. A pop-up appears that says that an update will start. After a few seconds the device will reboot and install the update.
If this doesn't work, plug in the USB stick and restart the device with a needle in the reset button. When the device starts up move one finger on the touchscreen around and wait for a green detected message at the top of the screen. The update will start.
Problem solvingI don't have a *.upd file
That is OK, the file does mot contain any information. Just create a new empty file and rename it like the *.bin file. As example, if you have a 8259.bin create a 8259.upd file.
The device doesn't recognize my USB thumb drive
There are 2 USB connectors on the back of the device. If one does not work, try the other. Make sure your thumb drive is formatted as FAT32.
Firmware FilesThis list is made by taking links from different firmware threads (found in first post). Every entry has a link to the original posts. Please be careful when flashing, the files need to match the correct CPU and screen resolution. If you have files for the normal V1 or different screen resolutions you can send me a PM.
Junsun V1 Pro | 8259 | 1280 x 720:
DownloadOriginal PostVerified8259P_军灿UI02v1280x720-国外_v20_20210907.ziphere8259P_军灿UI02v1280x720-国外_v27_20211201.ziphere8259P_军灿UI02v1280x720-国外_v31_20220225.ziphere8259P_军灿UI02v1280x720-国外11_v1_20220323.ziphere8259P_军灿UI02v1280x720-国外11_v3_20220422.ziphere8259P_军灿UI02v1280x720-国外_v44_20220920.ziphere8259P_军灿UI02v1280x720-国外_v50_20221226.zipheremopfi
Junsun V1 Pro | 8227L:
DownloadOriginal PostVerified8227L_8军灿UI03-国外10_v7_20210814.ziphere8227L_8军灿UI03-国外10_v21_20211130.ziphere8227L_8军灿UI03-国外11_v3_20220714.ziphere
Junsun V1 | 8667Q | 720 x 1280:
DownloadOriginal PostVerified8667Q军灿UI02-国外-VHD720x1280_v11_20211207.ziphere8667Q军灿UI02-国外-VHD720x1280_v12_20220214.ziphere8667Q军灿UI02-国外-VHD720x1280_v13_20220510.ziphere8667Q军灿UI02-国外-VHD720x1280_v23_20220801.ziphere
Factory ResetSettings -> Car Infotainment -> About Device -> Settings Icon -> Code 8878 -> Erase all Content
ADB ConnectionPreparation
Activate Developer options. You have to click a few times on the build number until you are a developer: Settings -> System -> About Car -> Build number
Activate USB debugging. Settings -> System -> Developer options -> USB debugging
Use the 4-pin USB connection on the back of the device. Connect with a USB A <-> USB A cable. My device had a female Mini USB adapter for using a Mini USB cable.
ConnectUse adb to connect to the device
Bash:
adb shell
Problem solvingADB can't find any devices
It could be that the ADB connection with the device is not working. This means that the corresponding option is not set. This can be done temporary or permanent.
Temporary Connection
To make the connection with adb work temporary we can change the USB setting of the device. To do that we need to set Settings -> USB Preferences -> USB controlled by -> This device. No it should be possible to connect via ADB. The connection is temporary, because after a reboot it is gone and has to be set again.
Permanent Connection
We can enable the connection permanently by changing a value in the secret menu. Go to Settings -> About Device -> Cogwheel (top right) -> Code 8878 -> Others -> USB2 Debug -> Enable
Can't find USB Preferences
Go to Settings and click the search icon in top right corner. Type in usb and then click USB controlled by.
RootCreate boot.imgConnect via adb to the device and find the location of the boot partition. The star '*' has to be replaced according to your device. For my Junsun V1Pro it is bootdevice. In the next step we will create a copy of the boot partition. Please be careful with dd command. It will overwrite wrong files or partitions if you do a mistake.
Bash:
adb shell
su @#zxcvbnmasdfghjklqwertyuiop1234567890,.
ls -l /dev/block/platform/*/by-name/
dd if=/dev/block/platform/*/by-name/boot of=/sdcard/boot.img
Patch boot.imgInstall Magisk apk on your device. I used Magisk v23.0 from here: https://github.com/topjohnwu/Magisk
Open the app and click on top right Install button
Then click next and choose Select and Patch File
Select your boot.img and let Magisk patch it.
Copy the new created file to your computer. The filename will be similar to magisk_patched_23000_***_boot.img
Bash:
adb pull /sdcard/magisk_patched_boot.img <older_on_your_computer>
Flash magisk_patched_boot.img
Bash:
adb reboot bootloader
fastboot flash boot magisk_patched_boot.img
fastboot reboot
Writable SystemTo make the system writable we need to remount the partitions.
Bash:
adb shell
su @#zxcvbnmasdfghjklqwertyuiop1234567890,.
remount
Now we need to reconnect and then we can write to the system (i.e. copy a file)
Bash:
adb shell
cp /sdcard/myapp.apk /system/app
Reserved
Reserved
Hey all, I need help with my junsun v1 pro 4gb +64gb-mtk8259- I just had it installed and everything works except Bluetooth. I can make calls from unit and or my cell phone. Apparently the people I call can hear me but I can't hear them. On occasion as it dialing I hear the ringing for a second then it cuts out. Is this a hardware issue, install issue, or something I need to change in secret menu?? I've reached out to junsun with no luck. I fixed the issue with the swc thanks to this forum!! Hoping someone can help me. Car is chrysler 300c and phone is samsung galaxy note 20.
Cubanlink81 said:
Hey all, I need help with my junsun v1 pro 4gb +64gb-mtk8259- I just had it installed and everything works except Bluetooth. I can make calls from unit and or my cell phone. Apparently the people I call can hear me but I can't hear them. On occasion as it dialing I hear the ringing for a second then it cuts out. Is this a hardware issue, install issue, or something I need to change in secret menu?? I've reached out to junsun with no luck. I fixed the issue with the swc thanks to this forum!! Hoping someone can help me. Car is chrysler 300c and phone is samsung galaxy note 20.
Click to expand...
Click to collapse
Hi, I have the same problem, if you have found a solution to the problem please share it with me! Thanks!
I am trying to mess with the secret menu. Like bt sync type, volume, three is various options in there related to Bluetooth just don't want to screw it up worse. Hopefully someone can shed some light cuz if not I'm returning it. I'll have to pay to take it out....ughh...I love the look though, if not I would just get pioneer but it don't look stock like this
So I Brought it back to my installer and he fixed it. Apparently in my car the speaker inputs were reversed, that why I couldn't hear anyone through speakers. He told me some cars with 6 plus speakers have this problem when installing these type of units. Loving the unit now that's its all fixed.
Hello
I have Junsun V1 pro 4/64g and my unit is hanging on Google boot logo (Android 9).
Does some one know how to get to recovery to do wipe cash / do factory reset?
Thanks
I have the junsun v1 1gb, it does not enter the google play services.
I would like you to provide me with a ROOM image to update or factory reset.
Thanks!
bartekm01 said:
Does some one know how to get to recovery to do wipe cash / do factory reset?
Click to expand...
Click to collapse
I'm actually also looking for a way how to boot into the recovery. Haven't found one at the moment.
For your problem you could try and flash an update (or same version again). Description is in this thread.
Hi
Unfortunately updates are also not booting / updating while reseting. Plugging USB pendrive with update files to second USB port and against resting button still can't manage to update - radio is botting "normally" and ends up with bootloop
Try both USB ports.
Plug the drive in turn the device on and then move a finger on the touchscreen. I do a left right movement. If that doesn't work you will need to do it with the mtk tools and a scatter file.
Hi!! Are there any way to disable calls from SIM card ? Thanks
Hi, I purchased the Junsun V1 pro 6gb/128gb and am pretty happy with it. All the important things connected and worked straight away which was grand. One thing I wanted to check is the battery draining problem and the cutting of the 2 wires to prevent this. I found the Junsun diagram and on there it seems it's the red and orange wires (that "look" to run from the main black block to the black power block for the head unit). The query I have is those wires on my loom run from the canbus white block to the black power block in the head unit. Pictures attached to hopefully show this a bit better. Excuse the terminology Has anyone had any experience with this at all? TIA
Hi Everyone,
Can someone please help me how to factory reset code or the new firmware my Junsun v1 pro 9 inch 8G + 128 GB Radio chip MS98. i tried 8888 or 8878 but i can see no factory reset only factory setting.
thank you advance.
Hey does anyone know how to completey reset the AutoLink app? I tried disabling and enabling again but. Nothing works. I just want to get ride of Android auto activated from AutoLink.
Sowmaxwel said:
Hi Everyone,
Can someone please help me how to factory reset code or the new firmware my Junsun v1 pro 9 inch 8G + 128 GB Radio chip MS98. i tried 8888 or 8878 but i can see no factory reset only factory setting. View attachment 5572199
thank you advance.
Click to expand...
Click to collapse
I have the 6gb, not sure what chip. When you go into the menu after code 8878 it should say on the right in the middle "Erase All" I think. Then it asks you if you want to factory reset.