hi guys, tried to flash N910CXXU1ANJ4_N910COXA1ANJ4_N910CXXU1ANJ4_HOME.tar
and this came up (file attached)
what to do?
its N910K
thanks
The rom is for the N910C and you have the N910K. Install a specific rom for your device.
i get the same error even with 910K rom...
Odin Error
Shtihi said:
i get the same error even with 910K rom...
Click to expand...
Click to collapse
This happened to me and I freaked! Problem for me is I was already rooted. After flashing new firmware and error occurs, pull battery, boot back into odin and re-root the phone and reboot. My phone booted right up after doing this. Hope this helps.
Related
Not to sure if this in the right place. my phone was updated by kies this morning. i then tried to install omega 4.3 but it failed and wouldn't let me restore my back up. i then tried to flash a stock rom that i got from sam mobile and it wouldn't work i keep getting a msg on the phone sayin su check fail fuse 2 binary 1. i can still connect with odin and flash the atuo root any help here would be much appreciated some one has told me i need a copy of the very latest updated fw i am on I9505XXUBMF8 also after flashing atuo route when the phone reboot it loads the s4 screen the goes black and vibrates any help would be appreciated thanks kyle
kylewismith said:
Not to sure if this in the right place. my phone was updated by kies this morning. i then tried to install omega 4.3 but it failed and wouldn't let me restore my back up. i then tried to flash a stock rom that i got from sam mobile and it wouldn't work i keep getting a msg on the phone sayin su check fail fuse 2 binary 1. i can still connect with odin and flash the atuo root any help here would be much appreciated some one has told me i need a copy of the very latest updated fw i am on I9505XXUBMF8 also after flashing atuo route when the phone reboot it loads the s4 screen the goes black and vibrates any help would be appreciated thanks kyle
Click to expand...
Click to collapse
i maybe wrong but you have to root again when you flash stock tw you will lose root
kylewismith said:
Not to sure if this in the right place. my phone was updated by kies this morning. i then tried to install omega 4.3 but it failed and wouldn't let me restore my back up. i then tried to flash a stock rom that i got from sam mobile and it wouldn't work i keep getting a msg on the phone sayin su check fail fuse 2 binary 1. i can still connect with odin and flash the atuo root any help here would be much appreciated some one has told me i need a copy of the very latest updated fw i am on I9505XXUBMF8 also after flashing atuo route when the phone reboot it loads the s4 screen the goes black and vibrates any help would be appreciated thanks kyle
Click to expand...
Click to collapse
bootloader locked.
you can not downgrade. flash MH8
odin fails at id0/005> aboot mbn if this helps any 1
samersh72 said:
bootloader locked.
you can not downgrade. flash MH8
Click to expand...
Click to collapse
where can i get it and do i still flash with odin?
kylewismith said:
where can i get it and do i still flash with odin?
Click to expand...
Click to collapse
http://www.hotfile.com/dl/243289856/5f90db9/I9505XXUDMH8_I9505OXXDMHA_BTU.zip.html
yes with odin.
perform wipe after flashing
samersh72 said:
http://www.hotfile.com/dl/243289856/5f90db9/I9505XXUDMH8_I9505OXXDMHA_BTU.zip.html
yes with odin.
perform wipe after flashing
Click to expand...
Click to collapse
many thanks will give it a shot:good:
samersh72 said:
http://www.hotfile.com/dl/243289856/5f90db9/I9505XXUDMH8_I9505OXXDMHA_BTU.zip.html
yes with odin.
perform wipe after flashing
Click to expand...
Click to collapse
appears to be working kudos smashersh72 very great full for your help :victory:
When Kies upgraded the firmware it updated the bootloader. Unfortunately you are stuck on Official firmware MHG8 and higher. There are some roms out now with an official MH8 base and you might be able to flash the CM110 roms BUT at this point
Omega is MH1 base so you can't flash this...
Hey guys
I have a Hong Kong Note 3 N9005. Yesterday I flashed the 4.4.2 sammobile update to my phone using ODIN 3.09. I had auto reboot and f.reset ticked. The ROM was put in AP and I hit start. Then I received the error Invalid ext4 Image. Turns out that Hong Kong versions of the N3 cannot install European ROMs. Since then I have not been able to boot my device into android. I just loop into download mode telling me it detected a firmware update. Kies was no help.
The update DID update the bootloader, so now I cannot go back to stock ROM. I have tried a few things. I tried flashing the stock Hong Kong ROM MK1, it fails. So i found a guy that fixed a similar problem buy removing the aboot.mbn file and repacking the ROM. Tried that too and the ROM flashes but it leaves me in a bootloop. Phone turns on says booting recovery then restarts. I also tried cf-root in an effort to flash another ROM still not working. I cannot get into recovery mode no matter what I do.
It seems I have run out of ideas and am reaching out for help.
Robbbie said:
Hey guys
I have a Hong Kong Note 3 N9005. Yesterday I flashed the 4.4.2 sammobile update to my phone using ODIN 3.09. I had auto reboot and f.reset ticked. The ROM was put in AP and I hit start. Then I received the error Invalid ext4 Image. Turns out that Hong Kong versions of the N3 cannot install European ROMs. Since then I have not been able to boot my device into android. I just loop into download mode telling me it detected a firmware update. Kies was no help.
The update DID update the bootloader, so now I cannot go back to stock ROM. I have tried a few things. I tried flashing the stock Hong Kong ROM MK1, it fails. So i found a guy that fixed a similar problem buy removing the aboot.mbn file and repacking the ROM. Tried that too and the ROM flashes but it leaves me in a bootloop. Phone turns on says booting recovery then restarts. I also tried cf-root in an effort to flash another ROM still not working. I cannot get into recovery mode no matter what I do.
It seems I have run out of ideas and am reaching out for help.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2507403 flash this with cwm or twrp should work
jaythenut said:
http://forum.xda-developers.com/showthread.php?t=2507403 flash this with cwm or twrp should work
Click to expand...
Click to collapse
Hello thanks for replying.
Only problem is I cannot get into cwm or twrp. Any advice on what I can do to try to get CWM or twrp working? I can flash with ODIN. But with the CWM I tried it still just boot loops and does not allow me to get into recovery.
Thank in advanced.
Robbbie said:
Hey guys
I have a Hong Kong Note 3 N9005. Yesterday I flashed the 4.4.2 sammobile update to my phone using ODIN 3.09. I had auto reboot and f.reset ticked. The ROM was put in AP and I hit start. Then I received the error Invalid ext4 Image. Turns out that Hong Kong versions of the N3 cannot install European ROMs. Since then I have not been able to boot my device into android. I just loop into download mode telling me it detected a firmware update. Kies was no help.
The update DID update the bootloader, so now I cannot go back to stock ROM. I have tried a few things. I tried flashing the stock Hong Kong ROM MK1, it fails. So i found a guy that fixed a similar problem buy removing the aboot.mbn file and repacking the ROM. Tried that too and the ROM flashes but it leaves me in a bootloop. Phone turns on says booting recovery then restarts. I also tried cf-root in an effort to flash another ROM still not working. I cannot get into recovery mode no matter what I do.
It seems I have run out of ideas and am reaching out for help.
Click to expand...
Click to collapse
Same Issue here. I tried to install the 4.4.2 N9005XXUENA6_N9005OXXENA5_N9005XXUENA2 update on my Note 3 via odin 3.09.
Got an ext4 update failed error.
After this, the phone's bricked and is stuck on the Kies Recovery Screen. I tried to go into recovery mode in Kies, but it says this model does not have initialization.
I tried installing a 4.3 N9005XXUDMK3_N9005TNLDMK1_N9005XXUDMK2, but again failed. Download mode shows SW REV CHECK FAIL : [aboot] Fused 3 > Binary 2
Can someone please guide me to unbrick my phone?
I don't know what ROM I was on initially. It was the stock ROM that came with the phone.
I dont have CWM and TWRM installed.
Robbbie said:
Hey guys
I have a Hong Kong Note 3 N9005. Yesterday I flashed the 4.4.2 sammobile update to my phone using ODIN 3.09. I had auto reboot and f.reset ticked. The ROM was put in AP and I hit start. Then I received the error Invalid ext4 Image. Turns out that Hong Kong versions of the N3 cannot install European ROMs. Since then I have not been able to boot my device into android. I just loop into download mode telling me it detected a firmware update. Kies was no help.
The update DID update the bootloader, so now I cannot go back to stock ROM. I have tried a few things. I tried flashing the stock Hong Kong ROM MK1, it fails. So i found a guy that fixed a similar problem buy removing the aboot.mbn file and repacking the ROM. Tried that too and the ROM flashes but it leaves me in a bootloop. Phone turns on says booting recovery then restarts. I also tried cf-root in an effort to flash another ROM still not working. I cannot get into recovery mode no matter what I do.
It seems I have run out of ideas and am reaching out for help.
Click to expand...
Click to collapse
Got this response from MrAndroid12 in another thread I'd started:
"This is not a brick at all. Just add a .pit file and restart the upgrade via Odin again.
You should be fine."
I don't know how to add a .pit file though.
I am certain the bootloops are because it flashed the new bootloader. I think your best option is to wait for a dev like indie to release Omega V7 and try to flash that through Odin.
Or if you can extract the different partitions from the original thread you can try push them one by one with Odin.
hallydamaster said:
I am certain the bootloops are because it flashed the new bootloader. I think your best option is to wait for a dev like indie to release Omega V7 and try to flash that through Odin.
Or if you can extract the different partitions from the original thread you can try push them one by one with Odin.
Click to expand...
Click to collapse
It is the bootloader yes. But it NEEDS the bootloader to be able to boot in to KitKat. And there is no downgrading once you've installed the new BL.
Best option is to re-flash via ODIN again and not wait 2 weeks for a Dev to modify a custom ROM...
Solution
Here is the solution:
http://forum.xda-developers.com/showpost.php?p=49426283&postcount=14
m1ndst0rm said:
Here is the solution:
http://forum.xda-developers.com/showpost.php?p=49426283&postcount=14
Click to expand...
Click to collapse
Works thanks
Sent from my SM-N9005 using XDA Premium 4 mobile app
Hi,
I encountered error during flashing of XXUGNG4 official firmware using odin 3.09. It did not completed successfully. I have tried to change usb port but still got the same error. I managed to flash the custom recovery and restore my previous rom backup but got a warning 'kernel is not seandroid enforcing' and when my phone boot my camera and sound (volume,etc) is not working.
Question: Can I flashed XXUGNG4 official firmware even if my custom rom is XXUGNG8? I really need to go back to stock official firmware in order to fix the problems I encountering on camera and sound
Really need your help...
Thanks
kraven0731 said:
Hi,
I encountered error during flashing of XXUGNG4 official firmware using odin 3.09. It did not completed successfully. I have tried to change usb port but still got the same error. I managed to flash the custom recovery and restore my previous rom backup but got a warning 'kernel is not seandroid enforcing' and when my phone boot my camera and sound (volume,etc) is not working.
Question: Can I flashed XXUGNG4 official firmware even if my custom rom is XXUGNG8? I really need to go back to stock official firmware in order to fix the problems I encountering on camera and sound
Really need your help...
Thanks
Click to expand...
Click to collapse
Hi,
You cannot flash an older version of your firmware without encountering problems.
You need to flash XXUGNG8 or later.
Look here:
http://forum.xda-developers.com/showthread.php?t=2265477
Don't forget to wipe data and cache before and after flashing the firmware
malybru said:
Hi,
You cannot flash an older version of your firmware without encountering problems.
You need to flash XXUGNG8 or later.
Look here:
http://forum.xda-developers.com/showthread.php?t=2265477
Don't forget to wipe data and cache before and after flashing the firmware
Click to expand...
Click to collapse
I will try to download the XXUGNG8 firmware and hopefully it will fixed my problems and back to official firmware.
A friend tried to flash CWM ( http://forum.xda-developers.com/showthread.php?t=2201860 ) for s4 and it failed...and now the phone is stuck..it says: Firmware upgrade encountered an issue.Please select recovery mode in Kies & try again
Phone model: i9505
Some help please? I don't know what to do
EDIT: i found that i can flash the firmware with odin..but i still have a question..im not really sure what firmware i had before..so is there any problem if i install firmware from other country or carrier?
You can find latest stock fw for your phone here.
wvw.sammobile.com/firmwares/checker/
I can't post external links so change wvw to www
waynevan2000 said:
You can find latest stock fw for your phone here.
wvw.sammobile.com/firmwares/checker/
I can't post external links so change wvw to www
Click to expand...
Click to collapse
thanks but.. the phone isnt starting that's why i have to flash a firmware..so i can't check what firmware i have..
The flashing process failed at half of it..:/......
Just pick one of the latest.
btw if the flashing of the recovery fails then just try the standard stuff
- different usb port
- different cable
Lennyz1988 said:
Just pick one of the latest.
btw if the flashing of the recovery fails then just try the standard stuff
- different usb port
- different cable
Click to expand...
Click to collapse
Finally worked to flash a firmware..i used europe firmware from here http://forum.xda-developers.com/showpost.php?p=41072392&postcount=2
Aaaaand when the phone started, a error keeped showing up: samsung keyboard stoped working...and i entered in recovery menu and did a factory reset, and that error is still showing.... some help?..maybe i should flash other firmware? which firmware? i really don't know what firmware it had before..
And one more thing..i cant even connect to wifi because it says something about security error something that the system blocked an unwanted action or something like that :/..something from knox :/
PS: i flashed just the AP file but the firmware had more files :/..
raulx222 said:
Finally worked to flash a firmware..i used europe firmware from here http://forum.xda-developers.com/showpost.php?p=41072392&postcount=2
Aaaaand when the phone started, a error keeped showing up: samsung keyboard stoped working...and i entered in recovery menu and did a factory reset, and that error is still showing.... some help?..maybe i should flash other firmware? which firmware? i really don't know what firmware it had before..
And one more thing..i cant even connect to wifi because it says something about security error something that the system blocked an unwanted action or something like that :/..something from knox :/
PS: i flashed just the AP file but the firmware had more files :/..
Click to expand...
Click to collapse
Why did you want to flash a custom recovery, to just flash a custom rom? If so, then just flash the custom recovery again and then flash the custom rom you want.
And why would you just flash the ap file if the firmware has more files? Makes no sense to me.
Lennyz1988 said:
Why did you want to flash a custom recovery, to just flash a custom rom? If so, then just flash the custom recovery again and then flash the custom rom you want.
And why would you just flash the ap file if the firmware has more files? Makes no sense to me.
Click to expand...
Click to collapse
Thanks! i managed it.. 2 S4 devices got Imperium v13 ROM
I was trying to install cyannogenmod 13 on my tab 4 smt230 and I formatted the whole device.
I now am trying to flash the stock image but it is not working TWRP keeps on saying flashing failed
Any ideas what to do???
Nuggets321 said:
I was trying to install cyannogenmod 13 on my tab 4 smt230 and I formatted the whole device.
I now am trying to flash the stock image but it is not working TWRP keeps on saying flashing failed
Any ideas what to do???
Click to expand...
Click to collapse
Search(and learn) about Odin(its thing for samsung devices) with it you should be able to restore you tab.
Thanks for the advice. I will try Odin to flash a new rom
I have tried using odin to flash the stock rom but it failed and said Firmware Upgrade Encountered an Issue and turned off. I now cannot turn the device on please help me
Edit: I charged it up fully and tried again. It now works.