Related
I woke up this morning to find my 8525 sitting in my computer chair as usual. Only to reach over and grab it, and ....its sitting in three inches of water. I have no idea what happened, or how it got there. All i know is my phone wont turn on, and is totally dead. Is there ANYTHING that can be done to right this horrid tragedy? Any help would be a gift from god. Thanks
Wow.
Sorry about that.
Let it dry out before trying to use it. Since it's wet, you have nothing to lose by taking it apart to facilitate this. You could dry it faster by using a hair dryer but NOT on the heated setting.
agreed; but let it dry for a day or two before you try, you should also put it somewhere that will provide additional moisture evaporation (gas oven with pilot lights or a furnace room, behind a PC fan or the like). i saved my old Sony S710a by letting it bake in my hot car for about 6 hours while i was at work. just make sure its totally dry before you try, and considering you already voided the warranty with the pool of water incident, you might as well take it apart if you can to make sure its completely dry.
hmm, bad luck.
Try all the above suggestions. But make sure you have disconnected your battery
Tried putting the battery back in after about a good 4-5 hours of being in the sun. All i get is a crackling noise when i try to place the battery to the metal conductors
Ewww.. I know it is stressful for you not to switch on the phone, but doing that will just make matter worst. Since you said that it wont turn on, I presume that you've tried it once (Strike 1), and you did it again 4-5 hours later (Strike 2), which usually others just leave it for at least 1 day (but probably the sun does help).
Can you identify what water is it? Can there be mineral within? Which may cause a short circuit somewhere in the phone. You'll need to open up the phone and clean it up somehow.. either DIY or get some phone shop people to do it. Your warranty is 'washed' anyway.
Try This
Stop Drinking!
Read This To Possible Save You Phone
OK, this comes from my many decades in the electronics industry.
1. PULL the battery. Do not put it back in in few hours.
2. Where did the water come from? Was it really water or? You need to know this. It's real important because mostlikly the PCB is contaminated. Anything that got inside has most likely contaminated the board and will cause shorts, intermitent contacts and the like. Even rain or spring water, it's the minerals...
What you have to do most likely is disassemble the unit. Get a gallon of DISTILLED (not Spring) water. Distilled, also know as deionized is free of all minerals. You are going to have to carefully submerge the board without the LCD in the water and gently rub it with a very soft tooth brush while underwater. Next take it out and put in another bath of distilled water. Agitate it gently. This proces should remove any contamination as long as the offending liquid is not sticky or heavily acidic or base. In the case of the later 2, you are most likely screwed.
Ok, so now you have a wet board. Genly shake the excess water off of it. Turn your oven onto WARM. Nothing above 150 F. Let it warm up and then shut the oven off. Put the PCB in the middle of the oven directly on the rack, close the door and come back 8 to 10 hours later. If the board isn't dry, repeat the steps again.
If you are luck and didn't fry it from trying to power it up, it may work again.
I have saved lots of radio equipment from rain & saltwater submergence this way.
Feel free to PM me if you need to. Good Luck.
I used to have a motorola and dropped it into a bucket of water. Dried out in a few days and it was working fine.
my 8525 recently fell in the sink. as soon as i seen it in the sink i pulled the battery out. rigged the phone up on something in the floor so air could ventilate under and over, set the hair dryer on high (but without the heat) and 5 or so ventilation fans from a desktop pc wired to a 9v battery. let the hair dryer go for about 15 minutes but left the fans on over night. took the phone with me to school the next day and left it in the car during both of my classes. came out put the battery in and powered it up. works just fine now
http://www.wikihow.com/Save-a-Wet-Cell-Phone
ive heard the rice thing works, ive alway wanted to flush with alcohol, that would in theory dilute the water and the alcohol would dry out faster.
Ok so heres the deal. I put the battery in. Power up the phone, gets to the vp3g startup screen, then fades to white. Could someone point me in the direction of a tutorial that shows me how to disassemble a Hermes CORRECTLY.
Hopefully ill be able to give it a DI Water bath and breath a little life back into her. Thanks for all the help guys, I really appreciate it
It's drying out slowly. I had a Hermes that did the same thing - eventually getting to the "screen behavior" you describe. I never fully disassembled it. I just let it sit open, with the battery out, keyboard pulled out, and the back off. Eventually (after leaving overnight), it was fine. Worked normal ever since that with one exception.. I had forgotten to pull the SD card. The SD socket never worked again :-(
Moral of the story: don't forget to take out the SD card.
todd_jg said:
It's drying out slowly. I had a Hermes that did the same thing - eventually getting to the "screen behavior" you describe. I never fully disassembled it. I just let it sit open, with the battery out, keyboard pulled out, and the back off. Eventually (after leaving overnight), it was fine. Worked normal ever since that with one exception.. I had forgotten to pull the SD card. The SD socket never worked again :-(
Moral of the story: don't forget to take out the SD card.
Click to expand...
Click to collapse
yeah i got lucky. when mine fell in the sink i had the SD card out and in the laptop doing hw. so i guess im really lucky that the sd socket still works
Not worried about the SD card as much... Anyway, Ive popped the back off of my 8525 after removing a couple screws. On the back of the circuit board there is white material that can be wiped off with a little rubbing alcohol and an ear swab. What is that crap? Ill go further in depth here soon once it fully drys. I sure hope I can get this thing running again, birthday is the 13th and would be a nice little gift to myself to get the phone working. Thanks for the help guys
WOW Just look it here...Thats what I call the Power of Unity man. Great piece of work, info. I love all You people. If the world learns anything from XDA developers then there wont be any more human sufferings I am sure..Enjoy friends the power of forum..
If it fades to white, it is still wet.
You need to let it dry a lot longer before trying to use it.
Sterch said:
On the back of the circuit board there is white material that can be wiped off with a little rubbing alcohol and an ear swab. What is that crap?
Click to expand...
Click to collapse
Well, those are either stuff from the water or stuff from your phone that is washed and gathered to form some dangerous circuits (much like coffee water rings, that things tend to get to the edge of waters). These stuff may conduct electricity, hence making your phone goes nuts. Search and destroy all these 'crap' Good luck. Don't try the phone unnecessarily until you are sure that all 'crap's are gone. One of these 'crap' may potentially kill your phone (ok, it is usually not that serious, but just incase )
Sad story, I was lucky with similar story, but much cheaper. I left my Nokia BH-600 Blue Tooth Head set in my panties and give them to washing-mashine. 40 degrees program for 30 minutes ended by wringing on 800 turns/minute
When I found it in the pocket I just left it to wither up and it didn’t worked. So I tried to re-charge it and WOW it works and the battery has normal capacity.
Video of 8525 / Hermes being dismantled
Sterch said:
...Could someone point me in the direction of a tutorial that shows me how to disassemble a Hermes CORRECTLY ...
Click to expand...
Click to collapse
Don't forget the popcorn: http://www.youtube.com/watch?v=zsljpn74SW0
today was a horrible day...
apparently leaving your g1 in your pants while they are in the wash doesnt work so well.
does not power on
anyone have any idea what can be done to bring it back or is it most likely fried
and if it is done then does anyone want to buy it as is?
I guess this is an excuse to get a g2
*UPDATE*
I guess no G2 for me just yet.
My phone works great now. Did not do anything special. Did disassemble the phone though so I can wipe down any residue i saw on main components such as the keyboard.
My advice to anyone that has this misfortune is not to rush things. I think i turned my phone on 2 days too early but I got lucky and it did not affect my phone. I figured this out because there was a lot of visible moisture in the screen when the backlight turned on. The keyboard was not functioning correctly either.
I did leave it in rice for about 36 hours but I do not really think that did much as far as the drying process goes. Best thing to do is go to a hardware store and pick up a torx driver set(mine was $4 at Home Depot and it was 36 piece set including torx philips hex slotted and pozi) open up the phone *be careful* of course and let it air dry for 3-4 days (not absolutely necessary to take apart the entire screen but if you feel comfortable go ahead). While it was open I wiped down the main board and the keyboard. I did not take apart the screen because I just did not want to take any other risks(mostly because i knew the screen worked) even though there was moisture, I knew it would eventually dry out. But the key to all of this was patience(I know its tough to go 3-4 days without your baby).
the link for the service manual is http://mikechannon.net/PDF Manuals/HTC Dream SM (A04).pdf
Most of the time, phones can live through the washer and live. You MUST take out the battery and do NOT attempt to turn it on for atleast 48 hours, as you will likely short out the phone. Put the phone in a big bag of rice to let it soak up the water, also use a blowdryer to help dry the phone out. However, your warranty is now void, and there likely will be some remnants of water within your screen.
Yep! worst thing you can do is turn that thing on (or try) before its dry.
my g1 hasnt had a bath but other phones have (none with touch screens) and i take as much apart as possible and leave it that way till the waters gone (then like 4 more days just to me sure )
artifical drying sources reccomended (dont get too hot!!!)
I have had it in rice for about 24 hours now and its sitting on top of my dvr because it gives off a little heat so it should help the process.
just remembered that i didnt remove the sd card...
i was thinking that since it was in the washer with detergent, shouldnt i have just removed the battery and try to clean it in some type of solution...
I have read about a alcohol solutions but kind of scared and i just noticed that there is condensation around the edges of the screen
I'd say take it apart, Blow dry what you can, leave the pieces in a warm area for a couple hours, and then try putting it back together and turning it on.
anybody know how sensitive the screen is because i want to try and blow some heat on it but not sure if it will damage it
best part about handset insurance cover lost or stolen phones...hint hint
bladepbc said:
best part about handset insurance cover lost or stolen phones...hint hint
Click to expand...
Click to collapse
good point but im on att network using the g1 unlocked...
plus i rather not cheat my way out of it because this is my own fault
good news and bad news...
first of all it powers on and boots fine. Secondly the screen seems to be working perfectly (touch and all)
bad news i might have turned it on too early because screen still had noticeable water spots all over it. The keyboard also just spews random letters and commands (ie one of the letters controls the volume)
other good news 1.5 has onscreen keyboard
anyone have any advice on how to go about fixing the keyboard?
Advise for fixing the keyboard: take it apart and clean it.
ok well im taking it apart to clean it out and i see some residue but what should i use?
microfiber cloth?
cleaned out as much as i could but seems like the menu button is now acting up while the keyboard is still messed up
Aside from parts made of paper, parts with thin films (like the lcd), speakers, batteries, or fine parts that are difficult to dry, you can do a very neat job with 99% iso alcohol followed by deionized (aka distilled) water. This includes most (but not all) plastic casing, buttons, pcb boards, etc. Follow up with a hair blowdryer set on low heat (or if you have an electric heatgun, even better).
Get a semi-shallow dish, fill it with the solvent, submerge the part and scrub it lightly with a soft toothbrush. (probably don't scrub for polished surfaces like the exterior casing). Then directly rinse it under a stream of the deionized water. Finally, clean the dish out, fill it with the di water and scrub with the brush.
^ almost exactly what I did to recover a "dead" water soaked phone. Worked great, and learned a lot about how the phone is built
couldnt find 99% near by but got 91% which im assuming should work...
is it ok if i use bottled water(kirkland)?
oh and the spots on the screen are still there (light and dark areas)
thanks for the help guys
kp126 said:
couldnt find 99% near by but got 91% which im assuming should work...
is it ok if i use bottled water(kirkland)?
oh and the spots on the screen are still there (light and dark areas)
thanks for the help guys
Click to expand...
Click to collapse
I bought my 99% iso from Safeway. It comes in a 16oz container. Look for it in the medical supplies aisles. Don't use bottled spring/mineral water, as that contains... minerals. You need buy deionized (also referred to as distilled) water. Distilled water contains a significantly lower amount of mineral ion, which for the purpose of cleaning electronics would be considered contaminants.
Do the spots appear to be blotches of moisture? Perhaps there is fluid trapped between the various layers of the lcd.
ok ill go check out safeway tomorrow morning. thanks for clearing up the water thing.
it looks like its moisture because after leaving it off for about 5 or 6 more hours i saw a few spots fade a little bit.
I will take the screen apart tomorrow as well. Any special instructions on handling the screen or even cleaning it?
You might want to search for the service manual for the G1. It details a complete teardown and rebuild of the dream hardware.
some sort of a miracle just occured because my phone is not acting up at all anymore and i didnt even clean it with the alcohol solution yet.
Just woke up in the morning and turned on the phone and worked perfectly, with absolutely no problem with the keyboard(except that i think i forgot a screw and a few keys are a little loose) everything works fine.
only problem is that the screen still has what looks like condensation.
but the blotches in the screen seem to be slowly fading. Gonna pop it open right now and leave it out overnight.
thanks for the help
oh and the manual has a few mistakes in it as far as procedure goes but any person with common sense should be able to get past those
Damn, thats rough man. I dropped both my old phones in the toilet(damn you superbowl, damn you!!!)and both of them worked after taking them apart and drying them off but never really worked 100% the same...
Just a note too, those were non-touch screen phones.
Best of luck.
Hi folks!
Just wanted to post this, as it really surprised me.
I went to a swim the other day (about 2 weeks ago) and forgot, that I had my HD2 in my Pocket.
It was about 0.5 hrs under water. Afterwards I yelled... then took out the battery and tried to dry it with a hairdryer.
It did not help. It stayed dead (The paper indicator are in a bright pink now)
Then about 1 week later I finally found the time to buy a new battery. I put it in and then... it worked.
After about 5 or 6 hrs using time, the last bit of water in the screen (a nice 3D effect ;-) dryed and I have absolutely no difference whatsoever. Working like a charm, no problem.
Maybe it helps so.
JoC
lucky you ;-)
Wow, happy you. Don't try this at home
lol, how many hd2's have been sold? thats a one in that many chance occurance, and no mistake.
just wow
Wow I cant believe it still works. Id wanna shoot myself!
If you get your phone wet don't use a hair dryer to dry it coz it overheats metal parts so the circuits melt.
In the words of homer simpson DOH! cant believe it worked after
as long as the internal complete dry, u shouldn't have problem to turn it back on.
The best thing you can do with a phone that has been for a swim (completely submerged in water) is to pull the battery off and soak it in isopropyl for 30 min or so. This should get the water out of it. Then leave it out to dry until completely dry.
Iven if a wet phone works initially, it generally wont be long before the components begin to corrode. The isophopyl will drive out any water and then completely evaporate.
u are one lucky guy lol
very very lucky, my friend sneezed on his and it stopped working...
Built HTC Tough
Sentinel196 said:
The best thing you can do with a phone that has been for a swim (completely submerged in water) is to pull the battery off and soak it in isopropyl for 30 min or so. This should get the water out of it. Then leave it out to dry until completely dry.
Iven if a wet phone works initially, it generally wont be long before the components begin to corrode. The isophopyl will drive out any water and then completely evaporate.
Click to expand...
Click to collapse
Even better, since this phone already soaked for half an hour, with the battery out soak and then flush it well with distilled water to remove all the minerals that could cause corrosion, then stick it in a container of desiccant or rice if you're cheap
Alcohol especially soaked that long could be harsh on adhesives, surfaces and components in the phone.
Water itself isnt bad for electronics, its the minerals that are in the average tap, pool, beach, lake water. Distilled water has none of these minerals. Also any liquid tends to damage things like the camera and LCDs where it can get between the glass covering and LCD and backlight causing water spots to develop that are hard are just about impossible to remove.
If you do go the isopropyl route, id say do a very quick flush with it, and then make sure you are using 90%, usually in a red labeled bottle at the drug store, normal isopropyl is something like 65% alcohol and the remainder is water!
Really the best option for either route is to completely disassemble the phone then flush and dry while disassembled, but i know thats hard for some people to do without completely damaging it cosmetically. Remove things like the LCD, Camera, and speakers as these could be further damaged by subsequent soakings in either water or alcohol. These parts may need to be completely replaced depending on the existing damage
im supprised no one has asked this but,
HOW DO YOU GO FOR A SWIM WITH YOUR HD2??????
Did you go fully clothed or something? or do you normally keep your HD2 in the pockets of your swim shorts?
Me too
Hi,
I also took my leo swiming. Now loud speaker isnt working. can anyone help where i can get one?
Oooo, that's interesting...for your next test...microwave the phone for half an hour.
Yes.. I had it in my swim shorts. Before I went to the pool, I thought: "Be aware of that phone, don´t forget it in the pockets..." -> That didn´t help...
Yeah, our HD2 is a great phone.
Redeyedrichard said:
Oooo, that's interesting...for your next test...microwave the phone for half an hour.
Click to expand...
Click to collapse
xD hilarious
and distilled water won't screw up your device? so lets say, if I want to clean my screen randomly, I should use that?
I immediately removed it from the water, and desperately tried to remove the back case to remove the battery (its quite hard when the phone is wet) i got there eventually though.
The screen was flickering whilst the phone was still on, and the water sensitive stickers on the battery and phone are both pink. I've blow dried it for about 10 minutes haven't tried to start it back up yet.... any suggestions?
joeyjoee said:
I immediately removed it from the water, and desperately tried to remove the back case to remove the battery (its quite hard when the phone is wet) i got there eventually though.
The screen was flickering whilst the phone was still on, and the water sensitive stickers on the battery and phone are both pink. I've blow dried it for about 10 minutes haven't tried to start it back up yet.... any suggestions?
Click to expand...
Click to collapse
DON'T start it for a few days. Put it in a warm place, leave it to dry for 48-72 hours and pray it works when you turn it on.
yeah just be patient and wait about 3-4 days to dry. but do not put it under direct sunlight
....and wash your hands
Try to put into bag with rice, and leave for couple of days...
DanijasDub said:
Try to put into bag with rice, and leave for couple of days...
Click to expand...
Click to collapse
put it in a bag of rice or leave out in the open?!?
put your phone into rice and keep bag closed
Basically you just need to make sure you dry it out thoroughly. Don't try to rush this process in a few hours. All the posts about leaving it somewhere warm (like an airing cupboard) are correct. Don't put it on top of a radiator or hot pipe, or in the sun as already suggested. The idea of putting it in a bag of rice is to help draw the moisture out. Never tried this method myself.... You really must be patient with this - managed to save my Touch Pro that got soaked in the rain last year....
okay so i've put the phone the battery and the sim on top of some rice in a bad behind my tv in my bedroom
rice like the others said or if you are a cigar person (or know someone who is) place it in an acrylic humidor w/ humidification beans.......I resurrected a M$ ZUNE my wife dropped in a rain puddle by doing this in my humidor
man, this reminds me of the time I dropped my phone in a bucket of puke from a heavy night. Still worked after I dried and cleaned it up.
"DON'T start it for a few days."
yup ..is correct wait until dry ... "rice" are good for absorb humilities ..
but If I not wrong ..after dry .the speaker of the phone will change ..just like my tytn II drop into "wash floor water", it still can use .. but the speaker sound change ...
Οh man , really bad luck..
hope it goes ok but be patient and let it dry manually !!!
my wife washed my cellphone once (left in pocket after heavy night of drinking). Took the battery out, let it sit on a counter for about a week. Phone recovered though it took the screen a while for the colors to all show properly.
I have read where people put their oven on warm and leave it overnight. I don't think this will hurt the phone since their won't be a power source in it.
Dropped in a sink with the tap running!
I dried it out under a hand dryer, then powered it up straight away. In hindsight this was pretty stupid, but it booted up ok. The only problem being the NAVPANEL would randomly appear and require a reboot. The next day that problem had gone away, and was replaced with a new problem - the Volume down button being jammed on! Also the battery life was reduced to about 10 hours. After a further 48 hours and a blast with compressed air (around the volume buttons) the phone has returned to 100% normal use - even the battery life is getting better, now upto about 36-42 hrs..... but I have bought a replacement for that anyway!!
Can't believe how lucky I was!
[Edit: Just saw you fixed it. Bravo! I'll leave this here anyway...]
Rice is good, unless you have any silica gel kicking about, the stuff you get in electronic packaging in the little paper bags/sachets that say "do not eat".
But yes, definately don't do what the majority do...
"I just turned it on to see if it would work..."
"You turned your phone/laptop on while it was wet... to see if it would work?"
"Yeah... why?"
*facepalm*
Happens about once a week in the PC store I work at. You could also try stripping it after it's dried and going over it with a carbon pen to remove any corrosion/residue.
After removing the battery, SIM, and MicroSD and gently removing any surface water.
One trick I found is to put a phone in the path of hot dry air for 30 minutes to a couple of hours. A clothes dryer vent works wonderfully for this since its temperature controlled (and timed) to keep from destroying the fabric in your clothes, and hot enough to allow water to evaporate. If you have access to your dryer vent hose, unhook it and rest it on top of the dryer and put your phone in the path (at least 4 to 6" from the opening). It's worked for 2 phones so far. One being my wife's Motorola, and one my Touchpro. If you have a dryer with an insert for shoes, you could use that as well, although I would put the phone on something to keep it from vibrating off.
You could use a hair dryer but keep in mind that hair dryers are not designed to be run continuously and the temperature is not technically regulated.
The trick is to get the temperature of the whole phone up to about 130 to 140 degrees and the water will evaporate. I would avoid shaking the water out of the phone or using pressureized air since that will push water into the delicate connectors, keypad matrix, screen, etc.
Let me give you a more scientific approach to your problem, i will try to explain as better as i can since english aint my primary language.
After you drop it in the water, your phone will never be the same for couple of reasons. First of all, when the water will dry, salt will "sit" on the connections and the weldings of the connectors, and that will slowly but steadily eat them. My saying is : " Never trust a phone that was dropped into water/coffee ". For you to be sure of your phone you need to strip it, and clean it with a spray for electrical appliances. Now there are 2 types of those sprays, one with oil and one with no oil in it. For your thing you need the NO-OIL one. Thats to make sure you wont get a loose joint and eventually your phone wont get broken.
If you dont feel like opening your phone and you dont feel comfortable with it, just ignore my post and just dry it out. What is 100% sure is that at some point it will break down, it depends on when though, from hardware to hardware.
Just my 2 cents.
Any time I get anything wet I IMMEDIATELY remove the battery, then I remove anything else I can from it: Sim Card, Memory Cards, etc. I don't like the rice idea because rice ALWAYS ends up stuck somewhere inside. I prefer setting my phone on some foil out in the sun for a bit (provided it's not too hot out) or just leaving it somewhere where it's warm to dry out. DO NOT BY ANY MEANS put the battery back in or turn it on until it is COMPLETELY dry. A minimum of a day if you even want to begin to chance it. If it was dropped in something other than relatively clean fresh water, I would keep everything out of it (battery, sim, memory cards, etc.) and dip it in a cup of distilled water a few times to clean any particles off, then let it dry again completely before turning it on. Just because an electronic gets wet, doesn't mean it won't work. The only way to kill it really is if you power it back on or the battery shorts it.
I went swimming at the lake with my old Nokia 5310 for 10 minutes before remembering it was in my pocket, I immediately took everything out when I remembered and left it in the sun for 8 hours and it worked fine for a year after until I threw it into a wall as hard as I could due to a frustrating girlfriend haha
U may have problems in the future... Since it was submerged in water some components will begin to rust... I suggest u take it to a mobile service shop so they can tell u what to do, or maybe they can fix it...
2 weeks ago it was raining so much that the whole parking was under water.
I jumped to my car and went home. Halfway I discovered that my phone was missing, so I went back and found it on the parking, laying under water for half an hour, 10 cm deep.
When I picked it up, even it was still under water the lock screen went on.
At home, after disassembly the phone, only under the battery cover where a few drops of water, futher the phone was dry. Even the headphone and micro-usb are no leaking path.
I use it now again for 2 weeks and it still works fine, without any trouble.
Bravo for HTC to make a phone, more than spashproof
brotsje said:
2 weeks ago it was raining so much that the whole parking was under water.
I jumped to my car and went home. Halfway I discovered that my phone was missing, so I went back and found it on the parking, laying under water for half an hour, 10 cm deep.
When I picked it up, even it was still under water the lock screen went on.
At home, after disassembly the phone, only under the battery cover where a few drops of water, futher the phone was dry. Even the headphone and micro-usb are no leaking path.
I use it now again for 2 weeks and it still works fine, without any trouble.
Bravo for HTC to make a phone, more than spashproof
Click to expand...
Click to collapse
Yes, htc is the shizz! I just brought mine back to life and everything works after dropping it on the deep side of my pool. On cases like mine, taking it apart right away and putting it on a bowl of uncooked rice for a week(just to be sure) and it will dry it completely!
Alas mine wasn't so lucky, fell in a puddle as I got into the car, grabbed it out, turned it off and removed battery, sim and SD, wiped as much water off as I could with tissues.
Left it for 2 days to dry, nada. Might be that the impact with the ground (wasn't that deep a puddle) killed it.
Embarassingly and luckily I'd only taken insurance out on it that lunchtime!
Wow, that's pretty impressive for a phone. Touchscreen phones are usually prone to most types of damage, but it's good to see being fully submerged in water didn't completely disable the phone.
You lucky guy
Hmmmmmm
I'm a little dubious... I spilled a really small amount of water from a glass on the bedside table onto my HD2. Even though I immediately jumped out of bed, cursed and wiped it dry, the water seeped into it. I could see the water in the LCD (it looked like a shadow that spread across the screen slowly over days). Two weeks later, the digitizer stopped responding to my touch even though the LCD itself still seems to work. I've hard reset the handset and that hasn't helped. I also tried heating up the unit a bit (without the battery) to try to have the water evaporate from it, but that hasn't helped either.
I took the phone into O2 who had their people look at it. Ultimately they said it was out of warranty because of water damage and that I could purchase a replacement (since I don't have insurance on it).
I'm considering trying to replace the digitizer, but it sounds like a lot of fuss and ultimately the phone won't be under warranty.
Annoying... I miss my HD2. I'm stuck with a Motorola Razr at the moment.
You can drop the phone in anything... aslong as the water does not have minerals that are conductive or prone to errosion it will be fine
[OP] just happen to have some clean water falling from the sky
I had a Blackberry Storm that once got submergered in baby oil.. It stopped working and I left it alone for A month or so...One day i picked it up and it started working... The LCD was messed up with Oil in it but other then that it worked...I opened it up and there was baby oil everywhere.... Got some distalled water and let it sit for a day or so to get it clean then replaced the LCD and it worked like new.
Distalled Water is H20 with notthing in it... As clean as water can get... Sine it has no conductive minerals you can drop a phone or PSP and it will work just fine.
Really?
I thought water itself was corrosive to metal? I can't imagine that the rainwater mentioned in the first post would be as clean as distilled water...
Anyway, I was wondering do you guys have have any suggestions? I have this lovely phone that boots up and I can't do anything with.
Should I just wait it out and see if it starts working again.
raduaz said:
I thought water itself was corrosive to metal? I can't imagine that the rainwater mentioned in the first post would be as clean as distilled water...
Anyway, I was wondering do you guys have have any suggestions? I have this lovely phone that boots up and I can't do anything with.
Should I just wait it out and see if it starts working again.
Click to expand...
Click to collapse
if it has clorine in the water then yea... most citys add a small amount of clorine in their water system......
the phone boots but its unresponsive?
we love stories
I dont want to THINK mine under water not to be under water NEVER