Around 11PM last night my phone's screen suddenly just stopped "turning on" - I recently had to replace it but it's been perfect in the last month. The digitizer is still registering touches and I can hear the clicks and notifications, just no screen.
Can anybody tell me which cable is the one that feeds the signal to the screen? I've torn it apart twice now to the same result. Tried gently "bending" and wiggling the phone with the back off hoping to see something pop up on the screen but no dice.
Thanks all...it'd be great to not have to buy a new phone.
Related
Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....
So my sister who also has an Aria dropper her phone and now there is a huge crack on the screen. She doesn't have insurance so she is trying to find an alternative way to fix it.
Simply replacing the screen would work, but another problem started happening when she cracked the screen. During a phone call, the screen will turn off, as it should, but when the call has ended, the screen stays off and the only way to turn it back on is to either pull out the battery and reboot the phone or to plug it into a charger.
Does anyone know how to solve this problem? Will replacing the screen fix the blackout issue? Or is this phone just trashed forever?
sounds like it destroyed the phone and the proximity sensor. i'm not sure if replacing the screen will fix this.
I actually had the exact same problem after dropping my phone during a call. I noticed that I didn't have to pull the battery to end the call if I held it up super-close to a really bright light (desk lamp, etc).
There were many times when I was on the street (in nyc), and had to find a bright light to hold it up to.
I dropped my Aria right on the corner with the ambient light sensor (in the upper right corner), which shattered the glass right in front of it.
Amazingly enough, after a few weeks, it started to get better and better - and now, nearly 4 months later (yea, i just deal with **** lol), it will hang up cals properly.
I'm actually working on replacing the screen right now, btw
Hello good folks,
I would like a bit of help with sorting my phone out. As of Thursday morning (2 AM or so) my phone has a black screen. The phone switches on, the touchscreen works (I can unlock it, put it to silent, hold the power key and tap the places on screen that would normally switch it off to do just that), the volume keys work, I can receive calls, the back light works.
Everything is as it should be, but I cant see a damn thing!
I should note that this happened once before, about a month ago and a few hours later it was back to normal. Also, I have noticed over the past few months a very small black circle at the top edge of the screen, about half a centimetre in diameter.
Please help!
Kindest regards.
It's the first time I read such an issue, your screen's probably defective.
To eliminate a probable OS issue, does the bootloader appear flawlessly ?
No, nothing appears at all. The screen is completely black at all times!
Your screen is malfunctioning, I don't know what's causing it and I don't know if you can fix it yourself either.
I think you are better off sending it back, if still under warranty.
Otherwise, ... ?
This just happened to me NOW....I'm waiting hopefully it will fix itself as i hear the HD2 heals itself LOL
A few weeks ago I dropped my GS4 coming out of the grocery store. It hit the curb on its side right at the volume button. The screen (glass and LCD) broke. The volume button also deformed slightly. The case I had on it offered no protection around the buttons or the top and bottom. Got an Otterbox on it now.
Anyway, after weighing my options I ordered a new screen was replaced it myself. The process is pretty straight forward and only took about 20 minutes. I could probably do it in 5 if I had to do so again. Since the replacement I've noticed a few odd behaviors. It doesn't seem to charge as quickly (could be my imagination, I have no hard data to back that up.) I had it on the charger for about 6 hours last night and it only got up to 86%. It was at about 25% when I plugged it in. To be fair, last night was the first time that's happened. I was using the same charger I've been using since I got it.
Its also fully waking when I wave my hand over it to check notifications. It used to just show the screen with the notifications and time. Now, that screen comes up briefly then goes to the unlock screen.
The replacement screen is an OEM Samsung screen for the i337. The internal markings are all correct and match the broken one. Any ideas why this is happening?
Okay, the charging thing seems to have been a fluke. Haven't had an issue with it since that night. The issue with it going to the lock screen when you wave your hand over the screen persists though. It is happening every time. Also noticing that when I make a phone call from the handset (not sure if its the same when I initiate the call from Bluetooth) that the phone volume slider appears on the screen. The volume doesn't change, the slider just appears.
So my son got the tablet wet. I let it dry out for a few days then turned it on. Everything seemed fine. It went to home screen but the touchscreen was unresponsive. After about ten second's the screen went negative kinda then blank. It still vibrates and makes noise from notifications and volume buttons. But the screen will not work. Is there a screen replacement I can buy and would that work to fix my problem? If so is there also a video on how to do so? Thank you