Hello everybody, I'm having this problem: every time that I try to flash a ROM using Odin I get an error, see the log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6102BVJME1_S6102BZTOMI1_S6102BVJME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> BcmCP.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Anyone can help me ???
Itachitops said:
Hello everybody, I'm having this problem: every time that I try to flash a ROM using Odin I get an error, see the log:
Anyone can help me ???
Click to expand...
Click to collapse
where have you got the firmware from - if you downloaded it from sammoible you need to split it first with splitfus2
else
download already split firmware from my firmware thread and fully follow the instructions
http://forum.xda-developers.com/showthread.php?p=51505106#post51505106
Related
Hey everyone,
I believe I just softbricked my phone, I tried to restore it back to stock via ODIN but it wont work,
Here is the error message from ODIN
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUAMDJ_I337MOYAAMDJ_I337MVLUAMDJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And it stuck on the screen that shows "firmware upgrade encountered an issue please select recovery mode in kies and try again"
WHAT DO I DO? :crying::crying::crying::crying::crying::crying:
Try flashing this http://forum.xda-developers.com/showthread.php?p=46943588 via Odin forI337MF3......cuz the one u used is for I337MDL ....
Swyped from BlueICESense_JBE
take a look at Jamison's guide just to see if you did some steps wrong
it is mdl so don't use the fw but the steps may be similar
http://www.infamousdevelopment.com/index.php?topic=115.msg890#msg890)*
I bricked my phone while trying to flash jasminerom.
I can't seem to get it back to stock with Odin. I'm using the correct pit file and stock but I always end up with this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUCNC4_N900VVZWCNC4_N900VVRUCNC4_HOME.tar.m d5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? Please help!
I have the SM-N900V with android 4.4.2
Does your phone boot? If so, turn it back on, enable USB debugging and try again.
Does USB Debugging help us to flash the firmware too ?...
Regards
No it does not aid flashing .
OP should download another firmware and try again .
roted my grand prime once and un root it but now icant do stock fimware on it pls help
the odin says like this
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
anaskonnengal said:
roted my grand prime once and un root it but now icant do stock fimware on it pls help
the odin says like this
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
pls help
Which firmware did u use? It must same firmware on your phone to flash.
anaskonnengal said:
pls help
Click to expand...
Click to collapse
Did You use check on Samsung site for newest Rom ? For your region of course.
extraing new md5 file ; and try flash odin
After a failed root attempt my s5 is stuck on the first start up screen, the one that says powered by android at the bottom. When I try to flash the stock ROM using Odin I get an error message on my phone saying:
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
This is my Odin log (I am using odin v3.09):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be appreciated.
Please help!
SecretAgentJeb said:
After a failed root attempt my s5 is stuck on the first start up screen, the one that says powered by android at the bottom. When I try to flash the stock ROM using Odin I get an error message on my phone saying:
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
This is my Odin log (I am using odin v3.09):
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be appreciated.
Click to expand...
Click to collapse
SecretAgentJeb said:
Please help!
Click to expand...
Click to collapse
Greetings,
Thank you for using XDA Assist. First, please do not bump a thread until at least 24 hours have passed. XDA Assist is a very busy forum and your questions will be addressed when someone is available to answer. I will, however, move this thread to your device's Q&A forum. Good luck!
I want to know this as well. I excluded the problem of different PC and different USB cable. Why is it so hard to flash back stock ROM?
I think you are trying to flash an old version, or one not meant for the sprint phone. The file you are flashing ends in NCB, the latest is OK4.
Need help i get soft bricked my samsung a5 2017 (LDU)
i brought LDU & installed A520FXXU2BQIH_A520FOJV2BQJ1_PAK from sammobile after installation phone sticked into GOOGLE FRP after 2-3 hours searching on youtube i found a method for google frp reset by COMBINATION file so i installed this file COMBINATION_FAC_FA60_A520FXXU3ARA3 in that 7.0 firmware A520FXXU2BQIH_A520FOJV2BQJ1_PAK now device get bricked also then i try more options too then i download
A520FXXU4BRA8_A520FOXA3BQL2_XEF & COMBINATION_FAC_FA60_A520FXXU4ARA4 still fail at wright system in odin also get back to 1st installed 7.0 firmware now get red error on device screen SW REV. CHECK FAIL. DEVICE: 4 BINARY:3
kindly help
Is your problem fixed or not.... If not the problem is with you binary.. You have to have one.. Your best and easiest way to solve your problem is to start all over again and flash your stock rom back and then root your phone.
Don't forget to backup your phone
thank you a lots for reply bro i did same what you said about me but all fail again take a look im not geek to understand kindly give me step by step solution.
with combination file in AP
COMBINATION_FAC_FA60_A520FXXU3ARA3_FAC3ARA3_CL12800524_QB16363926_REV00_user_mid_noship
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1509 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
AND WITH FULL FIRMWARE
AP_A520FXXU3BQLA_CL12637612_QB16162045_REV00_user_low_ship_meta
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4624 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ALL FAIL DEVICE TILL THE SAME KINDLY HELP
Single file
download and load single file firmwares of the country
ozkanasilioglu said:
download and load single file firmwares of the country
Click to expand...
Click to collapse
single file not available on sammobile.com
now what to do sir
How do u find the firmware and can I use any version as long as its the country firmware