[Q] Flashing firmware - Galaxy S 5 Q&A, Help & Troubleshooting

Hi, I have recently purchased a "SIM free" S5 phone, only to find out that it is not actually SIM free and has T-Mobile junk all over it! Anyway, I would like to know if it is possible to install firmware for the SM-G900F onto a SM-G900T without bricking it or losing any of the features? I have checked the forums before posting, however, I could find nothing conclusive whether this can be done or not. Thank you for your time

You can but you will lose wifi calling with a 900F fw.
Sent from my SM-G900F using Tapatalk

Hi Goldie,
I can live without that knowing that I can install Skype if needed! Do you know if there is anything else I will lose or is that simply it?
Regards
Simon RJ
Goldie said:
You can but you will lose wifi calling with a 900F fw.
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse

Well thats the only thing people on 900T have reported missing on my rom which is 900F based so if there is more I have no idea
Sent from my SM-G900F using Tapatalk

Hi Goldie,
Thank you for the info, however, I seem to be running into a brick wall where the flashing is concerned. I have downloaded stock firmware (I'm okay with it at the moment!) from Sammobile (G900FXXU1ANE2 OMD, G900FXXU1ANCE VOD and G900FXXU1ANE2 BTU) and none of these seem to work. Each time I plug my phone into the laptop, it always searches for the MSM8960 driver (according to Google is the Qualcomm chip, which eventually installs each time!) Then Odin fails each time with the same error message;
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
USB Debugging is on, all drivers installed, Odin v3.04 and 3.07 ran as Administrator. I have done this countless times with my S2 and my recently departed S4 successfully so I am stuck and looking to the experts for advice and guidance.
Message on the phone is
UDC Start
Secure Check Fail : aboot
Any help is greatly apprecitated
Simon RJ
Goldie said:
Well thats the only thing people on 900T have reported missing on my rom which is 900F based so if there is more I have no idea
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse

I've put in several hours of looking and the conclusion is that you can only flash tmobile roms on G900T which like i've said sucks. At the very least all snapdragon stock roms should be able to flash on snapdragons S5. In a half ass attempt I also tried to flash a G900F PIT onto the tmobile variant but the phone would not allow that. It mentions something about aboot and then PIT not correct. So at this point I think we are suck until one of the developers figures it out without tripping KNOX.
I also had a S2 international version and come to think of it now I never tried flashing a ATT or tmobile rom but who knew. I could flash any international rom though.

Related

SGH-I337 Softbrick? Odin flashing fails.

I own a model SGH-I337 Samsun Galaxy S4. Yesterday it started encountering several errors saying that processes had stopped, mostly android.process.acore and google.process.gapps. So I decided to factory reset, this didn't help. The firmware reset but I still encountered errors. I read somewhere this could mean a corrupt firmware in the phone, so I tried to flash the stock firmware from my computer using Kies. This failed and the phone now has no real firmware. So I tried to flash the firmware using Odin. (I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5)
Log:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
The phone displays this:
Start [224, 1440]
SV REV. CHECK FAIL : FUSED : 2, BINARY : 1
It still fails. I'm using the stock usb cable on a good port. I have updated the usb drivers as well. I've tried ending all Kies processes on my computer before flashing. This phone has never been rooted/unlocked. Please help.
You have MF3 firmware and tried flashing MDL. That's only going to make things worse.
Unrooted and not modded, you're still under warranty. Visit an at&t service and repair center or a Samsung Experience store (in some Best Buys) to help get this sorted. Cheers
I went to att today and told them that I got an update and didnt do it but it forced it and got stuck on the black sceeen wit samsung logo. They reflashed the mf3 os and that was it.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
xBeerdroiDx said:
You have MF3 firmware and tried flashing MDL. That's only going to make things worse.
Unrooted and not modded, you're still under warranty. Visit an at&t service and repair center or a Samsung Experience store (in some Best Buys) to help get this sorted. Cheers
Click to expand...
Click to collapse
Yea, last time I had a problem at&t tried to bull**** me saying it had water damage (it didn't and samsung fixed it for free) and wanted me to buy a new phone. Guess it can't hurt to try again though, thanks for the info.
Please read forum rules before posting
Questions and Help issues go in Q&A and Help section
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
It sounds like you have the MF3 firmware. At this point I guess all you can do with that is root it and use safestrap. No odin.
how do it flash 5.o1 lollipop on my s4 atnt i337 ? im on 4.4.2 kitkat

[Q] Stuck while "fixing" my SGH-I337

Hello everyone,
I'm a new poster here at XDA , and I've gotten myself into a bit of a predicament. If there are any rules that I happened to skim over that are broken, please let me know! I have performed a search of my issue, but no solution has been procured from what I can tell.
For three days now, I've been trying to fix my phone. Stats below:
Model: SGH-I337 (AT&T Galaxy S4)
Build Number: JSS15J.I337UCUEMK2
OS: 4.3 (JB)
I believe that's all that needs to be listed, I'll be able to provide more information upon request if necessary.
I'll try to shorten my story to the key elements: Less than a week ago I tried to root, unlock, and flash a custom ROM to my S4 to no avail. I completed the rooting successfully and I believe I may have bypassed unlocking it via LOKI, but the ROM did not install. Since that failed, I've been trying for three days to completely restore my phone to stock and just deal with Samsung's TouchWiz UI. I can flash (through ODIN) my phone to stock 4.3 and everything is fine except for a lack of WiFi and Data. This is where my conundrum comes in to play.
Knox seems to display a message stating "The device has detected an application attempting to perform actions that are not permitted. These actions have been blocked. It is recommended that you restart your device." anytime that I attempt to turn WiFi on. The widget and the setting in options will attempt to turn on for a split second and turn off prior to displaying this security message. It's as if Knox believes my WiFi is attempting to access parts of my phone that are restricted. My data is able to be turned on in the settings, but no 3g/4g is ever utilized. I figured an update off of 4.3 would help remedy this issue, but I can't seem to update my phone through any other means (ODIN, Kies, no OTA due to no WiFi/Data, etc.).
I've run out of different combinations of the keywords about my problem to search for in Google and any question about my problem was asked approximately April-October 2013, not answered, and not many more similar questions have risen since then.. which leads me to believe that this fix should be relatively easy.
On an S3 forum thread (I know, different device) I read that there could be corruption of my Nandroid system, but I'm not even sure what that entails. The user answering implied that the phone was done for. Again, though, this was a separate thread for another user about a Galaxy S3.
Well, apologies for the wall of text, folks. If you are willing to assist me, I would very much appreciate it. Thank you very much for reading my issue and I hope assistance can be organized.
What did you use to get back to stock
Sent from my SAMSUNG-SGH-I337 using Tapatalk
seedeh said:
What did you use to get back to stock
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Click to expand...
Click to collapse
I used ODIN to flash (What I'm very confident is) 4.3 Stock in the same manner I flashed the custom ROM.
I feel like that isn't specific enough for you though. I used Odin3 v3.09 first and then after several failures switched to Odin3 v1.85 as demonstrated in a few tutorials I've seen.
Did you use this tutorial?: http://forum.xda-developers.com/showthread.php?t=2621279 cause if you didn't, do.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
seedeh said:
Did you use this tutorial?: http://forum.xda-developers.com/showthread.php?t=2621279 cause if you didn't, do.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Click to expand...
Click to collapse
Let me attempt this thread's instructions before I make more of a fool of myself. Thank you for the assistance so far. I really appreciate it.
No problem
Sent from my SAMSUNG-SGH-I337 using Tapatalk
seedeh said:
No problem
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Click to expand...
Click to collapse
Seedeh,
The errors still continued as usual even with the explicit following of the linked directions. It appears that during the process:
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sbl1.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl2.mbn
<ID:0/007> sbl3.mbn
<ID:0/007> rpm.mbn
<ID:0/007> aboot.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
that the "NAND Write Start" step isn't really even trying to write before it fails.
Kies "Emergency Firmware Recovery" also yields no success due to "Firmware emergency recovery stopped due to GALAXY S4(SGH-I337) error. If the problem persists, please contact the Samsung service centre.", which does persist each time I attempt to do so.
If you have any more suggestions, I'd be more than happy to attempt them.
Thank you.
AmpGuitarChase said:
Hello everyone,
I'm a new poster here at XDA , and I've gotten myself into a bit of a predicament. If there are any rules that I happened to skim over that are broken, please let me know! I have performed a search of my issue, but no solution has been procured from what I can tell.
For three days now, I've been trying to fix my phone. Stats below:
Model: SGH-I337 (AT&T Galaxy S4)
Build Number: JSS15J.I337UCUEMK2
OS: 4.3 (JB)
I believe that's all that needs to be listed, I'll be able to provide more information upon request if necessary.
I'll try to shorten my story to the key elements: Less than a week ago I tried to root, unlock, and flash a custom ROM to my S4 to no avail. I completed the rooting successfully and I believe I may have bypassed unlocking it via LOKI, but the ROM did not install. Since that failed, I've been trying for three days to completely restore my phone to stock and just deal with Samsung's TouchWiz UI. I can flash (through ODIN) my phone to stock 4.3 and everything is fine except for a lack of WiFi and Data. This is where my conundrum comes in to play.
Knox seems to display a message stating "The device has detected an application attempting to perform actions that are not permitted. These actions have been blocked. It is recommended that you restart your device." anytime that I attempt to turn WiFi on. The widget and the setting in options will attempt to turn on for a split second and turn off prior to displaying this security message. It's as if Knox believes my WiFi is attempting to access parts of my phone that are restricted. My data is able to be turned on in the settings, but no 3g/4g is ever utilized. I figured an update off of 4.3 would help remedy this issue, but I can't seem to update my phone through any other means (ODIN, Kies, no OTA due to no WiFi/Data, etc.).
I've run out of different combinations of the keywords about my problem to search for in Google and any question about my problem was asked approximately April-October 2013, not answered, and not many more similar questions have risen since then.. which leads me to believe that this fix should be relatively easy.
On an S3 forum thread (I know, different device) I read that there could be corruption of my Nandroid system, but I'm not even sure what that entails. The user answering implied that the phone was done for. Again, though, this was a separate thread for another user about a Galaxy S3.
Well, apologies for the wall of text, folks. If you are willing to assist me, I would very much appreciate it. Thank you very much for reading my issue and I hope assistance can be organized.
Click to expand...
Click to collapse
Loki is for MF3 not for MK2. So you should just Odin back to stock. Here are the tar files.
http://forum.xda-developers.com/showthread.php?t=2621279.
If that didn't work, then follow ted77USA's guide.
Once you are back on Stock MK2 firmware, here are your options. Have a good read of this guide.
http://forum.xda-developers.com/showthread.php?t=2616221
Be sure to thank the op in the threads that help you & of the developers of the roms you flash. Good luck :fingers-crossed: & remember, reading saves phones.
John The Rhino said:
Loki is for MF3 not for MK2. So you should just Odin back to stock. Here are the tar files.
http://forum.xda-developers.com/showthread.php?t=2621279.
If that didn't work, then follow ted77USA's guide.
Once you are back on Stock MK2 firmware, here are your options. Have a good read of this guide.
http://forum.xda-developers.com/showthread.php?t=2616221
Be sure to thank the op in the threads that help you & of the developers of the roms you flash. Good luck :fingers-crossed: & remember, reading saves phones.
Click to expand...
Click to collapse
John The Rhino,
Thank you for you assistance. I will surely give credit where credit is due
I've attempted the XDA Full Odin Tar MK2 link's instructions three times on two separate computers (one w8 and one w7) to no avail. I've triple-checked the instructions, but my Odin always fails when attempting to Complete(Write).
NAND Write Start!
sbl2.mbn
sbl3.mbn
rpm.mbn
aboot.mbn
Complete(Write) Operation Failed
All threads completed. (succeed 0 / failed 1)
Odin settings: Auto Reboot checked, F. Reset Time checked, PDA = I337MK2_Full_Odin_Tar.tar file, nothing else is checked.
Device: Dev mode activated, USB debugging active, this is all verified after a recovery-initiated factory reset, device is in download mode.
Computer(s): Samsung Android ADB Interface drivers are installed, Odin does show a yellow bar upon device connection. MicroUSB cable is the default one that came with the device, all USB ports have been tried with the same results.
I tried to be as thorough as possible with my setup. I'll see if my process is correct now just in case that will help.
[Fixing Device to Working Status w/o wifi/data permissions] Flashed AP_I337UCUEMK2_1921628_REV06_user_low_ship_MULTI_CERT.tar.md5 via Odin
Automatic Reboot via Odin
[Device is back to working status w/o data/wifi permissions (No reset has been done)]
Power off
Reboot in Recovery Mode (Volume up + Home + Power)
Wipe data/factory reset command
Wipe cache (just in case)
Reboot
[Phone is now factory reset 4.3 MK2 (WiFi/Data permissions denied still]
Enable developer options
Enable USB debugging and Screen Stay Awake during charging
Power off
Boot into download mode (Volume down + Home + Power)
Open Odin3 v1.85
Bar in Odin for COM Port is yellow
Auto reboot & F. Reset Time are both checked
Load I337MK2_Combined_Odin_Tar\I337MK2_Full_Odin_Tar.tar.md5 in PDA slot
Screenshot of Odin before "START" http://i.imgur.com/oXufVNQ.png
Odin START
Wait for Odin to check .md5 compatibility
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MK2_Full_Odin_Tar.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl2.mbn
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Back to where these points began
Apologies for the length, but again I wanted to be as thorough as possible. My WiFi still won't turn on due to permissions issues and Data is on, but no 3g/4g/LTE comes through.
Surely I'm just missing an essential step or two.
Can you offer any further advice on this matter?
Odin can be finicky, try different usb ports, 2.0 not 3.0, and make sure you're using the cable that came with your device. I don't see that your doing anything wrong, keep trying.
Sent from my Nexus 5
The bootloader on MK2 and later is encrypted and without the key it will always fail. ODIN sees the ABOOT is locked and cannot flash the complete image. AT&T and Verizon have chosen this method to keep you off their cheaper competitors. I had to take my I337 to Best Buy Samsung experience to have it re flashed so that it would boot after a refused OTA from MDL and now it is a paperweight.
jd1639 said:
Odin can be finicky, try different usb ports, 2.0 not 3.0, and make sure you're using the cable that came with your device. I don't see that your doing anything wrong, keep trying.
Sent from my Nexus 5
Click to expand...
Click to collapse
I don't think Odin is the issue as it flashes what I like to call "The cure-firmware" .md5 AP_I337UCUEMK2_1921628_REV06_user_low_ship_MULTI_CERT.tar.md5) file just fine every time with no issues with Odin. Only when I try to flash that file, it works. I wish there was a way to tell what exactly is going wrong with the other files. I also can't seem to find where I located this file, but whatever it's doing works on my S4. I'd like to find either a 4.2.2 or 4.4.2 version of this stock OS that would work.
I'm beginning to wonder if it'd be more worthwhile to reroot, reset the flag binary counter, reset, and drive an hour and a half away to the closest AT&T store and see if they can fix my device. Does this sound like it may be my best course of action?
Again, thanks for all the help guys. I means a lot.
There is no way to downgrade to 4.2.2 from MK2. The bootloader is locked. Read the guide for MK2 it will help you.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
---------- Post added at 11:09 AM ---------- Previous post was at 11:04 AM ----------
Check your APN settings re enter according to correct settings posted on XDA.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Hey guys,
Solution confirmed!
I remedied the situation by flashing an NB1 firmware on the device. I'm aware that this firmware has a locked bootloader, but Loki is evidently a solution to that problem. I'll cross that bridge eventually when I cross it.
You guys are terrific and I really appreciate all the assistance that you've offered.
Take care.
AmpGuitarChase said:
Hey guys,
Solution confirmed!
I remedied the situation by flashing an NB1 firmware on the device. I'm aware that this firmware has a locked bootloader, but Loki is evidently a solution to that problem. I'll cross that bridge eventually when I cross it.
You guys are terrific and I really appreciate all the assistance that you've offered.
Take care.
Click to expand...
Click to collapse
Loki does not work with MF3 and up
Congrats!
Sent from my SAMSUNG-SGH-I337 using Tapatalk
AmpGuitarChase said:
Hey guys,
Solution confirmed!
I remedied the situation by flashing an NB1 firmware on the device. I'm aware that this firmware has a locked bootloader, but Loki is evidently a solution to that problem. I'll cross that bridge eventually when I cross it.
You guys are terrific and I really appreciate all the assistance that you've offered.
Take care.
Click to expand...
Click to collapse
Don't flash Loki to your phone, as it's only for MF3 not MK2 or above. You need to read the guide, which obviously you still haven't or you wouldn't be talking about flashing Loki on the new 4.4.2 Kit Kat firmware. Reading saves phones!
John The Rhino said:
Don't flash Loki to your phone, as it's only for MF3 not MK2 or above. You need to read the guide, which obviously you still haven't or you wouldn't be talking about flashing Loki on the new 4.4.2 Kit Kat firmware. Reading saves phones!
Click to expand...
Click to collapse
John The Rhino,
Thank you for the advice. I posted in a hurry earlier out of excitement and stated the incorrect method as you've pointed out. I'll be sure to be extremely thorough in the future when I decide to flash new software to my device. You've been a tremendous help and it is greatly appreciated.
Take care until my next issue. Haha.
Chase
AmpGuitarChase said:
John The Rhino,
Thank you for the advice. I posted in a hurry earlier out of excitement and stated the incorrect method as you've pointed out. I'll be sure to be extremely thorough in the future when I decide to flash new software to my device. You've been a tremendous help and it is greatly appreciated.
Take care until my next issue. Haha.
Chase
Click to expand...
Click to collapse
You're welcome. I'm glad it all worked out for you. As they say in the construction business, measure twice, cut once. Well same here, except I'd recommend as do others to read thrice (3x) FLASH once. Then you'll rarely have issues. Enjoy.
i337 same issue as original post
i have done the same research as posted in this link and read exhaustively every means google XDA and all the other pages dealing with rooting and flashing my AT&T s4 i337. I have ended up in the same boat as this guy with:
Baseband version - I337UCUFNB1
Build Number - JSS15J.I337UCUEMK2
i have attempted Kingo Loki, Motochopper, Odin(4 or 5 versions) adb flash in Linux(2 builds) and Winblows 7. My original desire was to have this build
https://www.youtube.com/watch?v=mJLKX_QWSpc
which got my hopes up immensely, as having wasted days upon days several times over the course of the last 9 months rooting this i337. The guy in the vid says he was able to get UT up and running following guidance from XDA. I want to be able to flash a twrp-like dual boot recovery to my device maintaining Andy functionality using UT as a daily driver.
I have read, as reading saves phones, everything I can glean from the aforementioned posts and forms, researched this thing to death and neded up with a phone with the knox-? security message listed in the original post. I have no Idea where to go from here, but know you guys do, as like a myriad of others, I worship this site like a god.
Please help an old retired disabled veteran of most of the sandy wars in the past 25 years. All I have now are my devices which bring me some comfort to my days.
I really need your help, as I've tried seemingly all and have a semi-dead i337.
buxtor, aka, Chief

Can someone please look at this and help...

I need this explained in the most laymen terms.. I have a S5, from US Stupid Cellular, being the idiot i am, i rooted the stupid thing thinking i would find a nice clean rom that i liked and it would not affect anything, low and behold to find out about this lame ass knox counter and that i was screwed at that point, i figured oh what the hell, but then to find out the bluetooth is ****, and i can get us cellular to unlock the pos because i cant get ota updates because stupid odin wont let me reflash the stock rom.. I am up to my ears in wondering why i ever got this stupid phone, but non the less i need help, i need the phone to reflash back to stock in two hopes that the bluetooth will work and that i can get the damn thing unlocked with out just strapping a hand full of m60's to it and screaming fire in the hole ...
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
I either get this message or the one all over the internet with no help about the dang pit crap, tried 4 usb 3.0 cables, 2 computers, 3 versions of odin and 2 different downloads of the same stock firmware..
Which model S5? and which version Android was it running?
Could be that the bootloader is locked, or that you are flashing for the wrong model
Check in download mode which model it says
Model SM-G900R4 running A5.0, Bootloader unlocked, both stock firmwares claim to be the uscellular g900r4 stock firmwares, i can see one being wrong but both? I have looked at many places to find these files..
Trying to flash from a native PC?
To be 100% sure the ROM you have downloaded is for that model, use this
http://forum.xda-developers.com/galaxy-tab-s/general/tool-samfirm-samsung-firmware-t2988647
0.3.4 is latest
Enter SM-G900R4 in "Model"
and USC in "Region"
Check the "Auto" box
Check Decrypt Automatically and Hit download
ROM will download as .zip, extract for .MD5, try flashing with ODIN 3.10.7 (Run as Administrator)

Odin not work

Hey Guys,
Edit
So it turns out you can't even flash the Canadian S7 to Tmobile's firmware. I installed the super stock rom and it started working again. I am not on the official Tmobile modem but I get service and WiFi calling so no biggie.
/Edit
This is driving me crazy. I bought the Canadian version of the S7 edge so I can put TWRP on it but I can't use odin on it. (SM-G935W8) Well at least I can't put the Tmobile files on it. Has anyone been able to do it successfully? I really need help, I'm losing my marbles, thanks guys!
I can't flash my appropriate radio so I can't get any service.
This is the error I get whenever I try to flash the radio.
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> RQT_CLOSE !!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Did you make sure the oem unlock is on?
gurnsey101 said:
Did you make sure the oem unlock is on?
Click to expand...
Click to collapse
Made sure OEM unlock was checked and USB Debugging was off. I am using the phone right now but I am not on USA radio so my service is not that great but I have WiFi calling so I am making due right now.
You need to ask in the section for your phone, not the software you want to load.
Try this:
https://forum.xda-developers.com/s7-edge/help/samsung-sm-g935f-sm-g935w8-rom-t3414612
joe3681 said:
You need to ask in the section for your phone, not the software you want to load.
Try this:
https://forum.xda-developers.com/s7-edge/help/samsung-sm-g935f-sm-g935w8-rom-t3414612
Click to expand...
Click to collapse
It's not software, it's the radio and bootloader. That thread had no information related to my problem? Maybe I missed something? Thank you for your time.
Well, you're trying to load TMobile software onto hardware with a different bootloader than the TMobile version has so...
joe3681 said:
Well, you're trying to load TMobile software onto hardware with a different bootloader than the TMobile version has so...
Click to expand...
Click to collapse
I'm not sure if you're trolling or not but I am NOT trying to install TMobile software. I am trying to install the radio from USA. I have done it before but for some reason this phone keeps giving me an error through Odin. I thought maybe someone knew of a way to sideload the radio. I searched and found fastboot but I cannot load up fastboot through my S7, I think they removed that feature? Anyway, in case you really aren't trolling you can install a radio that is not from your region as long as you have an unlocked bootloader (which I have now).
*Edit I installed the Tmobile CSC so I'm not sure why you're still hung up on Tmobile software
Your first post mentions twrp, then you mention files, then at the end radio so excuse me for not knowing which one of these you're inquiring about...
Don't get smart if someone is trying to help you and not understanding what your asking cause your OP is a cluster **** to make heads or tails of...
joe3681 said:
Your first posts and **** twrp, then you mention files, then at the end radio.
Don't get smart if someone is trying to help you and not understanding what your asking cause your post is a cluster **** to make heads or tails of.
Click to expand...
Click to collapse
I didn't mean to have an attitude sorry about that. I'm just frustrated because I feel like I am missing something, thank you for your help.
You got it now or no?
Have you tried the CP too which is the modem
joe3681 said:
You got it now or no?
Have you tried the CP too which is the modem
Click to expand...
Click to collapse
Not yet. I was able to restore the phone back to everything stock using Kies but I am still on the Canadian modem. I can actually get service now but now my main issue is I cannot use Samsung Pay since the radios do not match. I wonder if I get a Tmobile S7 edge serial number I can restore it with Kies?

Troubleshoot very weird boot problem

Sorry for the long post.
Got this sprint S7 as a 2nd hand unlocked phone a while back and worked quite nicely for almost a year. Now very often when I reboot it gets stuck on the LTE boot logo. While it is at it, it will burn through the battery in like 30m-1h, the phone gets very hot. This has already happened a handful of times so I try to never reboot unless very necessary. This doesn't happen on every single reboot though.
Right now it's showing the same issue. Before I've notice it'll do this for a few days and the like magic will start working again. It sucks because right now my phone is as good as dead.
The phone is not rooted and it's running stock ROM, with latest firmware and all updates(I checked for updates a couple days ago and there was none), but I don't know which exact version is at.
I've already tried rebooting into recovery and powering off and restarting from there. But no luck.
I had a strong suspicion this was due to switching sim cards (I moved a few months ago) and sometimes a "UICC unlock needed" (or sth like that) message has been shown but the phone continues to work. Today a friend mentioned it could be the battery. He said if the battery is damaged it could be causing problems on boot but I have no clue if that's true and/or how to check for it.
I'd thank anyone who could tell me how to troubleshoot this problem and find the real cause. I'm comfortable following some technical instruction to be able to grab logs from linux command line if someone taught me how.
Thanks in advance!
joel_gil said:
Sorry for the long post.
Got this sprint S7 as a 2nd hand unlocked phone a while back and worked quite nicely for almost a year. Now very often when I reboot it gets stuck on the LTE boot logo. While it is at it, it will burn through the battery in like 30m-1h, the phone gets very hot. This has already happened a handful of times so I try to never reboot unless very necessary. This doesn't happen on every single reboot though.
Right now it's showing the same issue. Before I've notice it'll do this for a few days and the like magic will start working again. It sucks because right now my phone is as good as dead.
The phone is not rooted and it's running stock ROM, with latest firmware and all updates(I checked for updates a couple days ago and there was none), but I don't know which exact version is at.
I've already tried rebooting into recovery and powering off and restarting from there. But no luck.
I had a strong suspicion this was due to switching sim cards (I moved a few months ago) and sometimes a "UICC unlock needed" (or sth like that) message has been shown but the phone continues to work. Today a friend mentioned it could be the battery. He said if the battery is damaged it could be causing problems on boot but I have no clue if that's true and/or how to check for it.
I'd thank anyone who could tell me how to troubleshoot this problem and find the real cause. I'm comfortable following some technical instruction to be able to grab logs from linux command line if someone taught me how.
Thanks in advance!
Click to expand...
Click to collapse
Have you tried reflashing the stock firmware via odin? If you could tell me which network you're using it on, I could point you to the firmware you would need. Here's a basic overview for the phones and their corresponding firmwares:
SM-G93OP- Sprint
SM-G930T- T-Mobile
SM-G930A- AT&T
SM-G930V- Verizon
SM-G930U- Universal, but you need the correct version of it for your carrier.
TheF|ipSide said:
Have you tried reflashing the stock firmware via odin? If you could tell me which network you're using it on, I could point you to the firmware you would need. Here's a basic overview for the phones and their corresponding firmwares:
SM-G93OP- Sprint
SM-G930T- T-Mobile
SM-G930A- AT&T
SM-G930V- Verizon
SM-G930U- Universal, but you need the correct version of it for your carrier.
Click to expand...
Click to collapse
Hi TheFlipSide,
I have a sprint version so I have SM-G93OP- Sprint
It is possible something might have gone wrong at some point in time but I have done factory resets before, I'm skeptical that the firmware itself could be the issue but I'm happy to give it a try.
Could you point me to the files needed to be sure I'm on the most accurate firemware (CP, BOOT, etc type of files).
Also, any issues with my phone being up to date with all the updates?
Personally I'd be happier to be able to flash sth like LineageOS but AFAIU there's not much support for this phone.
joel_gil said:
Hi TheFlipSide,
I have a sprint version so I have SM-G93OP- Sprint
It is possible something might have gone wrong at some point in time but I have done factory resets before, I'm skeptical that the firmware itself could be the issue but I'm happy to give it a try.
Could you point me to the files needed to be sure I'm on the most accurate firemware (CP, BOOT, etc type of files).
Also, any issues with my phone being up to date with all the updates?
Personally I'd be happier to be able to flash sth like LineageOS but AFAIU there's not much support for this phone.
Click to expand...
Click to collapse
You can't flash LineageOS on this phone because the bootloader is locked. You can get ODIN to flash the firmware with from here:
https://drive.google.com/file/d/0ByoIewGd_qk2MEZMb0l3Qlo4ek0/view?usp=drivesdk
Unzip it and click on the ODIN3 v3.12.7 file, you don't need to install anything it opens as an app.
Grab the firmware from here: http://updato.com/firmware-archive-select-model?record=48A2011F925C11E7963AFA163EE8F90B
Unzip it and select the files through odin:
CP in CP.
CSC in CSC.
AP in AP.
BL in BL.
Then go into options and select auto reboot and repartition, and keep everything else unchecked.
Hit start and wait for the firmware to flash.
Go into stock recovery, and wipe cache and factory reset.
Hit thanks on the posts if I helped you.
TheFlipSide thanks so much for helping me out.
Quick questions. The firmware link you sent is for SM-G930U. But AFAIK my phone is SM-G930P (Sprint model), since it even shows the Sprint animation on boot. Let me know if that was a small mistake or if theres a good reason to flash the Universal version on a sprint phone.
Also, assuming it was a small mistake I'm looking at that firmware page. Looks like the latest version for the SM-G930P comes in 3 flavors: VMU, XAS and SPR.
Do you know what those are and which one should i get?
Thanks again in advance!
joel_gil said:
TheFlipSide thanks so much for helping me out.
Quick questions. The firmware link you sent is for SM-G930U. But AFAIK my phone is SM-G930P (Sprint model), since it even shows the Sprint animation on boot. Let me know if that was a small mistake or if theres a good reason to flash the Universal version on a sprint phone.
Also, assuming it was a small mistake I'm looking at that firmware page. Looks like the latest version for the SM-G930P comes in 3 flavors: VMU, XAS and SPR.
Do you know what those are and which one should i get?
Thanks again in advance!
Click to expand...
Click to collapse
Use the SPR variant of the SM G930U firmware, as it comes without the Sprint bloat. If you still want to use the SM-G930P firmware, get it here: http://updato.com/firmware-archive-select-model?record=080CDA3799FF11E7963AFA163EE8F90B
As I said previously, you don't need to thank someone in a response post, just click the thanks button on a post which helped you.
bootlooped
TheF|ipSide said:
Use the SPR variant of the SM G930U firmware, as it comes without the Sprint bloat. If you still want to use the SM-G930P firmware, get it here: http://updato.com/firmware-archive-select-model?record=080CDA3799FF11E7963AFA163EE8F90B
As I said previously, you don't need to thank someone in a response post, just click the thanks button on a post which helped you.
Click to expand...
Click to collapse
Hi, sorry for the delay, life got in the way. So I downloaded the universal version SM-G930U (SPR) and followed the instructions and Odin failed.
Code:
<ID:0/006> Odin engine v(ID:3.1207)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn
<ID:0/006> lksecapp.mbn
<ID:0/006> FAIL! (Auth)
I tried to run it again after unplugging the cable and plugging it back in and it failed again:
Code:
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1207)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn
<ID:0/006> FAIL! (Auth)
Now I tried to restart and it's gotten itself on a boot loop =(
It's stuck in the blue "installing system update" page only for a second, then some white text on black screen shows up, and then it goes back to the blue page, and repeats. Basically is trying to boot into recovery forever.
Trying to reboot manually to get into download mode, or anything else also doesn't work.
Halp!
joel_gil said:
Hi, sorry for the delay, life got in the way. So I downloaded the universal version SM-G930U (SPR) and followed the instructions and Odin failed.
Code:
<ID:0/006> Odin engine v(ID:3.1207)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn
<ID:0/006> lksecapp.mbn
<ID:0/006> FAIL! (Auth)
I tried to run it again after unplugging the cable and plugging it back in and it failed again:
Code:
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1207)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn
<ID:0/006> FAIL! (Auth)
Now I tried to restart and it's gotten itself on a boot loop =(
It's stuck in the blue "installing system update" page only for a second, then some white text on black screen shows up, and then it goes back to the blue page, and repeats. Basically is trying to boot into recovery forever.
Trying to reboot manually to get into download mode, or anything else also doesn't work.
Halp!
Click to expand...
Click to collapse
You can't flash the U firmware if you are on the latest sprint firmware. Download the latest firmware from here
And follow the same directions for placing files into ODIN. You are getting the PIT error because of bootloader updates.
lvpre said:
You can't flash the U firmware if you are on the latest sprint firmware. Download the latest firmware from here
And follow the same directions for placing files into ODIN. You are getting the PIT error because of bootloader updates.
Click to expand...
Click to collapse
Hi Ivpre, thanks a lot for jumping in. So I managed to get my phone in download mode again. Also I google one more error that was showing up in the phone screen "Fuse 5 > aboot 4" (or sth like that, I can't remember exactly) and the internetz said that it was indeed due to having a version missmatch, the new one should be higher.
So I downloaded the latest G930P from sammobile site (G930PVPU5BQJ3) and got it to work again. I also found another thread to said the only thing to do is wait until a new G930U comes out.
What I don't fully get is that now that I've installed "latest" firmware. As soon as I configured the phone it said a new update is available. If I update it now, and a new version of G930U also comes out in a bit, will that mean I'll remain one version ahead? Should I not apply any updates until a new version of G930U is out? or should I try downgrading the current G930P ?
Thanks!
joel_gil said:
Hi Ivpre, thanks a lot for jumping in. So I managed to get my phone in download mode again. Also I google one more error that was showing up in the phone screen "Fuse 5 > aboot 4" (or sth like that, I can't remember exactly) and the internetz said that it was indeed due to having a version missmatch, the new one should be higher.
So I downloaded the latest G930P from sammobile site (G930PVPU5BQJ3) and got it to work again. I also found another thread to said the only thing to do is wait until a new G930U comes out.
What I don't fully get is that now that I've installed "latest" firmware. As soon as I configured the phone it said a new update is available. If I update it now, and a new version of G930U also comes out in a bit, will that mean I'll remain one version ahead? Should I not apply any updates until a new version of G930U is out? or should I try downgrading the current G930P ?
Thanks!
Click to expand...
Click to collapse
Yeah, apparently they just released a small update (QK3 maybe?) that patched an exploit. That update was just released the other day. You can take it or leave it, it shouldn't prevent you from installing the U firmware when it is updated.
If you really want to install the U firmware and can't wait, you can research PIT files, but it can lead to fully breaking the device if you mess up...personally, I would just wait. It was an old method that would work, but I'm not sure if it works on the new bootloader updates.
Hi Guys,
I'm on the same boat as joel_gil,
I've got S7 (originally purchased on sprint USA network) and now I've unlocked it using idoneapps without root.
I'm on G930PVPU5BQJ3 firmware at the moment and I'd like to flash G930U firmware which is network unlocked and not bloatware free.
I've downloaded the firmware below multiple times from sammobile.com and tried flashing using latest Odin 3.12.10 and everytime I am getting error message.
https://www.sammobile.com/firmwares/galaxy-s7/SM-G930U/SPR/download/G930UUES4BQL1/201542/
I have also tried XAS version as well but same result
SW check failed aboot fused 5 > binary 4 message.
I've got FRP and OEM unchecked and still its giving me same error.
I'd appreciate if you guys can have a look and help me please.
Many thanks in advance guys
tom_hungston said:
Hi Guys,
I'm on the same boat as joel_gil,
I've got S7 (originally purchased on sprint USA network) and now I've unlocked it using idoneapps without root.
I'm on G930PVPU5BQJ3 firmware at the moment and I'd like to flash G930U firmware which is network unlocked and not bloatware free.
I've downloaded the firmware below multiple times from sammobile.com and tried flashing using latest Odin 3.12.10 and everytime I am getting error message.
https://www.sammobile.com/firmwares/galaxy-s7/SM-G930U/SPR/download/G930UUES4BQL1/201542/
I have also tried XAS version as well but same result
SW check failed aboot fused 5 > binary 4 message.
I've got FRP and OEM unchecked and still its giving me same error.
I'd appreciate if you guys can have a look and help me please.
Many thanks in advance guys
Click to expand...
Click to collapse
You can't install the U firmware...the bootloader binary files are different. You will have to wait for the U firmware to catch up in order to install it. However, you can install the latest Sprint firmware without any issue.
I fixed it.
5 > BINARY 4 error, has to do with a Version 5 bootloader Sprint came out with in 2018. The fact that this is only affected by the SM-G390P further complicates things for the average user. Users on version 5 bootloader will need to wait until/If a version 5 universal bootloader for the SM-G930U to get unbloated firmware. Information on restoring your S7 SM-G930P to where you left off before you started trying to root your phone can be found below. More info on Sprint F'n us and BL Version 5, and how to tell the files apart can be found here
https://www.arencambre.com/blog/2018...omment-page-1/. There was a post on XDA (which I can't find) which gave the idea that Sprint came out with this version 5 bootloader to prevent people from flashing the phones to the U version and going overseas with them.
The stock files for the first version of Sprint Version 5 bootloader firmware dated 1-1-18 can be found here:
https://www.sammobile.com/firmwares/galaxy-s7/SM-G930P/SPR/download/G930PVPS5BRA1/206876/
Unzip. Only have auto reboot and Re-partition checked as options in Odin.

Categories

Resources