Hi All,
I tried to flash my phone with STOCK ROM by using RSD lite. I used an SBF file for this.
The status in RSD lite is showing as "Please manually boot up this device".
I have then unplugged the device and went into the bootloader by
pressing Power+Vol UP.Now I connected the device back to the PC and suddenly the RSD lite status shows as PASS but the mobile does not go past the Android boot screen.
I have tried using different SBF files but the result is same.
Has anyone face the same issue before or knows the solution to this problem??If so please share...
How long did you wait between appearing of the "Please manually boot up this device" message to booting?
I usually leave the phone for few minutes and it eventually reboots on it's own all the way to the stock, usable system and Android configuration wizard. I have never even tried to do this manually.
I waited for some 5 minutes and then searched on the internet if anybody else has faced the same problem...
The solution I found on the net was to disconnect the mobile from the USB port and connect it back again by entering into the bootloader mode.
Then the status on the RSD lite changed to PASS but phone is not getting through the boot logo of Android ...
Boot to stock recovery 3e. Press vol up + down at the same time. Clear cache and reboot. If still bootloop, enter stock recovery again, but this time do factory reset and reboot. Good luck!
antukubo said:
Boot to stock recovery 3e. Press vol up + down at the same time. Clear cache and reboot. If still bootloop, enter stock recovery again, but this time do factory reset and reboot. Good luck!
Click to expand...
Click to collapse
like what antukubo said, clear cache and do a factory reset then flash again.. this fixed my issue..
thrackanomir said:
How long did you wait between appearing of the "Please manually boot up this device" message to booting?
I usually leave the phone for few minutes and it eventually reboots on it's own all the way to the stock, usable system and Android configuration wizard. I have never even tried to do this manually.
Click to expand...
Click to collapse
+1. i've just done this yesterday and this is exactly what happened in my case as well. that is, just leave it as it for a few minutes and the phone will eventually rebooted itself to the system. that's when i unplug the usb cable.
Related
I rooted my phone this morning and tried to install the latest Gingerbread using this guide: https://droidmodderx.wordpress.com/latest-build-gingerbread-2-3-3-4-5-588-with-root/
Of course, my phone for whatever reason restarted after installing the first zip. After restarting, I couldn't get back to recovery or reboot the phone. I tried performing a factory reset, but that won't work either.
Is the phone bricked?
blackrobot said:
I rooted my phone this morning and tried to install the latest Gingerbread using this guide: https://droidmodderx.wordpress.com/latest-build-gingerbread-2-3-3-4-5-588-with-root/
Of course, my phone for whatever reason restarted after installing the first zip. After restarting, I couldn't get back to recovery or reboot the phone. I tried performing a factory reset, but that won't work either.
Is the phone bricked?
Click to expand...
Click to collapse
You will have to SBF
Sent from my DROIDX using XDA App
Thank you, after SBFing my phone and charging, I was able to re-root and install Gingerbread. Thank you so much.
Okay ... I'm having the same issue ... installed GB ... booted the phone up goes through the Moto Logo and the "Droid" & Red Eye then the short vibrate ... then it goes back to the "Droid" & Red Eye and starts all over again ... every once in awhile I catch just a glimpse of the home screen before it cycles all over again and twice I've seen a forceclose screen for Swype ...
I've tried "Safe" Mode (holding the menu key while booting) ... that gets me nothing ...
I've tried to boot into recovery (holding "Home" Key until Triangle Exclaimation), but when I get the triangle and go to hit the "Search" key nothing happens ...
I can't get the phone to stop log enough to get RSD to recognize it so I can flash it ...
Unless it "works" itself out of whatever issue it has with Swype (based on the forceclose error) I can't think of any other way to get it to stop long enough to flash it ...
ANY help would be greatly appreciated ...
Thanks
cybrjaz said:
Okay ... I'm having the same issue ... installed GB ... booted the phone up goes through the Moto Logo and the "Droid" & Red Eye then the short vibrate ... then it goes back to the "Droid" & Red Eye and starts all over again ... every once in awhile I catch just a glimpse of the home screen before it cycles all over again and twice I've seen a forceclose screen for Swype ...
I've tried "Safe" Mode (holding the menu key while booting) ... that gets me nothing ...
I've tried to boot into recovery (holding "Home" Key until Triangle Exclaimation), but when I get the triangle and go to hit the "Search" key nothing happens ...
I can't get the phone to stop log enough to get RSD to recognize it so I can flash it ...
Unless it "works" itself out of whatever issue it has with Swype (based on the forceclose error) I can't think of any other way to get it to stop long enough to flash it ...
ANY help would be greatly appreciated ...
Thanks
Click to expand...
Click to collapse
SBF. To SBF, you need to enter the bootloader. Follow these instructions (they're a little ways down the post):
http://forum.xda-developers.com/showpost.php?p=11118819&postcount=2
Don't forget to wipe data and cache AT LEAST THREE TIMES EACH whenever SBF'ing, or installing a new version of Android or a ROM.
Roland Deschain said:
Don't forget to wipe data and cache AT LEAST THREE TIMES EACH whenever SBF'ing, or installing a new version of Android or a ROM.
Click to expand...
Click to collapse
I have flashed almost every rom since the first update to froyo when I got this phone. That's with a 30.01 bootloader. That being said, I never wiped data or cache more than once. I have never had a problem. Wiping multiple times is only necessary if you have problems with it not wiping all the way
well my dad was having problems with his defy, running a stock us 2.2.1. I looked at his phone, and after a few minutes, it would freeze up, and go into a bootloop, or still screen of the motorola logo.
First thing i tried is the stock recovery, which would freeze as soon as i started to wipe cache, and or data reset. After that, it gets stuck on the motorola logo no matter what.
I thought flashing a different .sbf would work, tried it, and finally got it to load to the "Welcome to android - please touch to continue" screen, as soon as i touched it, it froze.
flashed - JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF
went into recovery again to try to hard reset, but once again it freezes when it starts to clear cache/data factory reset.
Reflashed, now its still stuck on the motorola logo.
Any help is appreciated, thanks
DH
The phone seems absolutely messed up.. can you send it back to service?
Motorola Defy, CM7 @ 1Ghz + CM9 multiboot
[Guide] Install double boot CM7 + CM9
[Guide][Root needed] Unsimlock your Defy
No I can't sadly, any recommendations?
Found a fix for anyone having this problem.v
Flash any sbf , and
Once its says "restart phone manually', exit the program, and unplug your phone, plug in your phone while in boot loader, them start the program,.and it should. Finish
the process, now you can clear cache and factory reset. Sorry I drank a little, the program is to install sbf's I can't think of the name
dyinghero27 said:
Found a fix for anyone having this problem.v
Flash any sbf , and
Once its says "restart phone manually', exit the program, and unplug your phone, plug in your phone while in boot loader, them start the program,.and it should. Finish
the process, now you can clear cache and factory reset. Sorry I drank a little, the program is to install sbf's I can't think of the name
Click to expand...
Click to collapse
Is the program RSDlite?
if yes the n how come when i was flashing a rom it never asks me to restart phone manually. and when i do quit the app any way and restart the phone in bootloader it does nothing.
Hi, im in the process of selling my phone and am following the tutorial on here about turning the phone back onto stock. The flash with flashtool was successful but im forever stuck on the boot screen? with now no way to go into custom recovery? i installed the correct rom for the phone so why hasnt it worked? thanks in advance.
dav08094194 said:
Hi, im in the process of selling my phone and am following the tutorial on here about turning the phone back onto stock. The flash with flashtool was successful but im forever stuck on the boot screen? with now no way to go into custom recovery? i installed the correct rom for the phone so why hasnt it worked? thanks in advance.
Click to expand...
Click to collapse
The only way I could get it to work was the following; however there is one thing to try before you try my way because mine did this also - after the wipe and flash with flashtool etc. The only way I found to get out the bootloop was to do a factory restore after when its looping. So from the boot screen loop hold the power button until it goes off then on then off again.
Then do the process to get into the recovery so hold down and power then release power as soon as the lg logo appears (first one) then press it again immediately that SHOULD get ya to the grey factory reset screen. Press the power button 3 x and it should do a factory restore and boot up this time. First boot may take a minute it should eventually start up.
Failing that try this - Open the lg mobile support tool and connect the phone in download mode (volume up and power with plugged in usb on mine) then go to options and upgrade recovery. it will download a file usually about 2GB then install it, the phone will reboot at 100% on the phone and 80ish% on the lg tool it will then start into the setup feature,
DO NOT disconnect the phone until it gets to 100% and finishes. This way you shouldn't need to do an extra factory reset.
I understand for this the phone needs to be seen on com 4 (it shows on the phone screen) so if necessary go into device manager with the phone still plugged in in download mode and select com ports then select the phone com port then right click >properties> advanced and change the com port to 4. It may tell u its already being used but don't worry it is fine. Save and exit device manager.
please bare in mind these are just my experiences on MY LG D802 however its worked every single time for me without fail and ive done it a good few lol.
HTH:good:
Hello all,
Any help with this would be seriously appreciated. I rooted my Nexus 10 a while back, maybe two years ago. I'm not very proficient with this stuff. Anyhow I decided to do the OTA upgrade to 5.0...I was concerned something would go wrong unless I went to stock first, but I read that the only thing that would happen is root would be removed.
Anyhow, the tablet appears stuck while booting. I see the Google screen first with the unlocked indicator on the bottom. A few seconds later is the Android logo on its back, a red triangle over it with an exclamation point and "no command" written below". It stays that way for a minute or so, tries to reboot and goes back to the no command screen. I can't even power off, when I try to do so it just powers back on by itself and ends up at the no command screen again.
I tried booting into recovery (power, volume up, volume down). My options from here are either Start, Restart Bootloader, Recovery Mode or Power Off. Every option I choose leads to the No Command Screen (except power off, which powers off). No idea what to do from here.
Any help at all would be appreciated. As you can probably tell I don't have much experience with this and just wanted to go back to unrooted stock. If you have advice, please be clear. I can follow directions well enough, just don't have much experience here. Thanks in advance.
Same here, bootloop.
Same thing here. A seemingly short download of Lollipop (even though I have 50Mbs internet). Installation, reboot, and now it loops endlessly. I can get to the bootloader or into Download mode, but that's all. Recovery mode just reboots. I was rooted and had TWRP installed. Other than that, I was running stock 4.4.4.
I've rooted all my devices, and installed various ROM's on several devices. I have the full ADB installation. I have the Nexus Root Toolkit installed. The problem is, the device will not show up under "Devices" on the computer itself. I've installed every USB driver there is (and uninstalled each one after it does not work, so no I do not have several USB drivers installed). Of course nothing shows up using "adb devices" either. Nexus Root Toolkit also cannot find any devices. I've read everything on this subject I can find, and there are no answers out there. Anyone have ANY ideas??
Thanks
Guys, if your device is connected in fastboot (try "fastboot devices") then you can flash roms or recovery (and then flash rom) from there. There are multiple threads with the same problems out there which were fixed. E.g: http://forum.xda-developers.com/nexus-10/help/bricked-t2948546
In my example, I flashed TWRP recovery from fastboot, then installed custom ROM from recovery (official ROM failed to install for some reason). Try this, it might help.
danweis said:
Same thing here. A seemingly short download of Lollipop (even though I have 50Mbs internet). Installation, reboot, and now it loops endlessly. I can get to the bootloader or into Download mode, but that's all. Recovery mode just reboots. I was rooted and had TWRP installed. Other than that, I was running stock 4.4.4.
I've rooted all my devices, and installed various ROM's on several devices. I have the full ADB installation. I have the Nexus Root Toolkit installed. The problem is, the device will not show up under "Devices" on the computer itself. I've installed every USB driver there is (and uninstalled each one after it does not work, so no I do not have several USB drivers installed). Of course nothing shows up using "adb devices" either. Nexus Root Toolkit also cannot find any devices. I've read everything on this subject I can find, and there are no answers out there. Anyone have ANY ideas??
Thanks
Click to expand...
Click to collapse
Go to Fastboot mode (pwr+both volumes), Than select recovery after a while an android with Exclamation mark appears which is a stock recovery screen. To access the stock recovery menu press and hold power than press one of the volume keys so the menu will appear. Than do a factory reset and clear caches. You can than reboot and wait for boot animation to finish (it wont take long this time) and you will boot.
If this doesnt work you can flash a stock factory image easily from fastboot again.
Aresmar said:
Go to Fastboot mode (pwr+both volumes), Than select recovery after a while an android with Exclamation mark appears which is a stock recovery screen. To access the stock recovery menu press and hold power than press one of the volume keys so the menu will appear. Than do a factory reset and clear caches. You can than reboot and wait for boot animation to finish (it wont take long this time) and you will boot.
If this doesnt work you can flash a stock factory image easily from fastboot again.
Click to expand...
Click to collapse
I also had the same problem... I followed these instructions and now my Nexus 10 can boot normally (it took a long time to boot).
Only problem is all my data was deleted.... stup*d f*cking sh*t!!!!!!!
Hi!
So i treid to install the twpr recovery via srk tool huawei
after i unlocked the bootloader and reboot the phone i got the ÿour device is booting now screen and i cant do anything
i tried to restart the phone then press the vol down + the usb cable and doesnt work i still get the same screen
can't acces erecovery, can't enter fastboot, i can't do anything
what do i do now?
Nickoll_no1 said:
Hi!
So i treid to install the twpr recovery via srk tool huawei
after i unlocked the bootloader and reboot the phone i got the ÿour device is booting now screen and i cant do anything
i tried to restart the phone then press the vol down + the usb cable and doesnt work i still get the same screen
can't acces erecovery, can't enter fastboot, i can't do anything
what do i do now?
Click to expand...
Click to collapse
Device stuck in device is booting now ? or the 3 option screen ?
Kcetin20 said:
Device stuck in device is booting now ? or the 3 option screen ?
Click to expand...
Click to collapse
The device is stuck in the "device is booting now':crying:
Same Problem...
Nickoll_no1 said:
The device is stuck in the "device is booting now':crying:
Click to expand...
Click to collapse
BLN-L24N - Honor 6x
Sooo, I have the same problem , here's my story. Please help I've resorted to using a SGH-T599N... Its embarrassing... I'd almost rather have an iPhone...
So Little ol' me was messing around/ deleted google play services/ reboot to twrp to recover but device ended up bricked. At the time, still able to access fastboot. I flashed recovery and firmware. I then tried dload roll back method and when it cleared the phone bootloader locked. So I unlocked bootloader again but when device re-booted the following screen came up and still remains:
" ' Your device has been unlocked and cant be trusted. ' -- ' Your device is booting now... ' " (No options are available.)
I eventually tried to restart to fastboot or erecovery BUT Everytime I try to power down the device, it tries to power up again but needs to charge for a minute before trying to boot itself back up. .(even after being on the charger for hours this happens). The problem with that is I can't get into fastboot or force dload because it automatically starts itself/ has to be plugged in until it turns back on. (Yes i've tried button mashing/ button holding/ etc. did not help)
How do I get the phone to charge, without it booting up? I have a feeling that if I can get it to start (without it first having to charge) I can get it to fastboot/ or erecovery. I have already tried to let the battery COMPLETELY drain.
Outside of that, I know the whole roll back and dload stuff. Currently it flashes the honor logo screen and then sits at "Your device is booting now..."
Bootloader is unlocked
OH! I should clarify, it boots on its own. I've tried disconnecting the battery, having it on the charger without the
battery. With the battery, Starting phone up by re-connecting the battery. No positive results
I'm about to start messing around with firmware flashing utilities, I just don't know of any. I wish there was a way to flash without being in fastboot mode. (I know very little of perl/python/linux, but I am a quick learner if you point me in the right direction.
Thank you in advance
MSDB714 said:
BLN-L24N - Honor 6x
Sooo, I have the same problem , here's my story. Please help I've resorted to using a SGH-T599N... Its embarrassing... I'd almost rather have an iPhone...
So Little ol' me was messing around/ deleted google play services/ reboot to twrp to recover but device ended up bricked. At the time, still able to access fastboot. I flashed recovery and firmware. I then tried dload roll back method and when it cleared the phone bootloader locked. So I unlocked bootloader again but when device re-booted the following screen came up and still remains:
" ' Your device has been unlocked and cant be trusted. ' -- ' Your device is booting now... ' " (No options are available.)
I eventually tried to restart to fastboot or erecovery BUT Everytime I try to power down the device, it tries to power up again but needs to charge for a minute before trying to boot itself back up. .(even after being on the charger for hours this happens). The problem with that is I can't get into fastboot or force dload because it automatically starts itself/ has to be plugged in until it turns back on. (Yes i've tried button mashing/ button holding/ etc. did not help)
How do I get the phone to charge, without it booting up? I have a feeling that if I can get it to start (without it first having to charge) I can get it to fastboot/ or erecovery. I have already tried to let the battery COMPLETELY drain.
Outside of that, I know the whole roll back and dload stuff. Currently it flashes the honor logo screen and then sits at "Your device is booting now..."
Bootloader is unlocked
OH! I should clarify, it boots on its own. I've tried disconnecting the battery, having it on the charger without the
battery. With the battery, Starting phone up by re-connecting the battery. No positive results
I'm about to start messing around with firmware flashing utilities, I just don't know of any. I wish there was a way to flash without being in fastboot mode. (I know very little of perl/python/linux, but I am a quick learner if you point me in the right direction.
Thank you in advance
Click to expand...
Click to collapse
So on ny phobe the mainboard is dead so i guess the internal storage is corrupted
I need to change that and i guess you need too...
It's not so expensive(like 40$ for my phone)
Nickoll_no1 said:
So on ny phobe the mainboard is dead so i guess the internal storage is corrupted
I need to change that and i guess you need too...
It's not so expensive(like 40$ for my phone)
Click to expand...
Click to collapse
do you have a part number?
MSDB714 said:
do you have a part number?
Click to expand...
Click to collapse
I dont think i was to a local service...it' s not so expensive but it's not cheap either