Soft Bricked Device; Keep Getting <ID:0/004> Complete(Write) operation failed. - Galaxy Note 3 Q&A, Help & Troubleshooting

I keep trying to reflash to stock and keep getting this error in ODIN:
<ID:0/004> Complete(Write) operation failed.
I tried running as admin and removing the SD card. No dice. I also tried reflashing a recovery, same error.
I tried following this and still get the same error: http://forum.xda-developers.com/showthread.php?t=2483380
Full error:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_N900VVRUBMI9_N900VVZWMI9_1671014_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sbl1.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> aboot.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Screen reads in red:
SW REV CHECK FAIL " [aboot]Fused 2 > Binary 1

Whitechapel420 said:
I keep trying to reflash to stock and keep getting this error in ODIN:
<ID:0/004> Complete(Write) operation failed.
I tried running as admin and removing the SD card. No dice. I also tried reflashing a recovery, same error.
I tried following this and still get the same error: http://forum.xda-developers.com/showthread.php?t=2483380
Full error:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_N900VVRUBMI9_N900VVZWMI9_1671014_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sbl1.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> aboot.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Screen reads in red:
SW REV CHECK FAIL " [aboot]Fused 2 > Binary 1
Click to expand...
Click to collapse
If you have gone to Kitkat then you can't go back to JB...
Also, there have been people who have trouble flashing carrier roms from the open roms...

Related

[Q] GT-I9505 Firmware upgrade failed.

I tried to upgrade my galaxy s4 to android 4.4.2 using odin.
But while performing the process, odin said it failed
now my galaxy says " Firmware upgrade encountered an issue. Please select recovery mode in kies and try again".
i am from Nepal.
Thank you
MODEL: GT-I9505
FCC ID : A3LGTI9505
SSN : -I9505GsMH
With this little information, there is not much we can do. You need to give more details if you want help.
What was the error? What firmware did you try to flash? What steps did you take? Did you try a different usb cable, different ports, different pc etc etc.
Lennyz1988 said:
With this little information, there is not much we can do. You need to give more details if you want help.
What was the error? What firmware did you try to flash? What steps did you take? Did you try a different usb cable, different ports, different pc etc etc.
Click to expand...
Click to collapse
i used odin v3.09.
I tried flashing with the stock firmware but couldnot.
steps i took is shown in attachments.
error in my odin is
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNC4_I9505YXYFNC1_I9505XXUFNC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sbl1.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl2.mbn
<ID:0/006> sbl3.mbn
<ID:0/006> rpm.mbn
<ID:0/006> aboot.mbn
<ID:0/006> tz.mbn
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!
yes i tried diffent pcs, and with different cables, and different usb port too..
sakarmaskey said:
i used odin v3.09.
I tried flashing with the stock firmware but couldnot.
steps i took is shown in attachments.
Click to expand...
Click to collapse
Try to flash the same firmware like the pic attached.
Joku1981 said:
Try to flash the same firmware like the pic attached.
Click to expand...
Click to collapse
same problem occured!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNC4_I9505YXYFNC1_I9505XXUFNC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sbl1.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl2.mbn
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!

Flashing ROM with Odin FAILed

I am trying to flash UK firmware on my SM-G900F but it fails.
Below is the log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900FXXU1BOH4_G900FOXA1BOH4_G900FXXU1BOH4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Can anyone help?

[HELP]I Think i bricked my phone. Please help me Out Thanks, [Solved :D]

Hi,
I mistakenly deleted my os and now i can't boot. When i flash it just get stuck. Recover-mode downloading blue bar just move a further and than stop. When i try to run my mobile there is a error message "Firmware Upgrade encountered an issue. Please select recovery mode in kies and try again." I can only open Recovery Mode,
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> tz.mbn
<ID:0/006> hyp.mbn
<ID:0/006> NON-HLOS.bin
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
please help me with this.
Edit: Change the port and it works

Failed root on SM-N910T now stuck at recovery booting

Bought this to make into a rooted note 4. Not my main phone yet, I have an AT&T version.
Attempted to root following the directions on CFROOT, that got me to this point. Now have spent 2 days searching for solutions and trying things. No progress!
In download mode Using Odin 3.9 and 3.10.7 the CFROOT file report success but stuck in recovery booting. Attempting to reinstall the entire firmware Odin log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Any help would be greatly appreciated!
John
dylistn said:
Bought this to make into a rooted note 4. Not my main phone yet, I have an AT&T version.
Attempted to root following the directions on CFROOT, that got me to this point. Now have spent 2 days searching for solutions and trying things. No progress!
In download mode Using Odin 3.9 and 3.10.7 the CFROOT file report success but stuck in recovery booting. Attempting to reinstall the entire firmware Odin log:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Any help would be greatly appreciated!
John
Click to expand...
Click to collapse
You're in the wrong place. These are the S4 forums, not Note 4.
Anyway, AT&T devices have a locked bootloader and I don't think CF-Auto-Root can root those.
So you may have to find another solution to rooting.
But before that you may have to flash the stock firmware again, as the current one is messed up by the failed root flash.
Thank you
I thought I had the right forum. Can I move this to another forum. Or should I start a new thread and delete this?
dylistn said:
I thought I had the right forum. Can I move this to another forum. Or should I start a new thread and delete this?
Click to expand...
Click to collapse
It can be moved. Select the report option and as a reason select thread moving.

Help with flashing fw to g928f

<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 3860 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> cm.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Im tryin to flash G928FXXU5CRI1_G928FTMZ4CRF1_G928FXXU5CRH3_HOME.tar.md5
Im new so I need every help.
Shootarz said:
Im tryin to flash G928FXXU5CRI1_G928FTMZ4CRF1_G928FXXU5CRH3_HOME.tar.md5
Im new so I need every help.
Click to expand...
Click to collapse
The stock image you flash should match your device. And he nougat or at least mm. If you got a Verizon phone you want Verizon stock for example. Sammobile will be your friend in this. Also. Did you install Samsung USB drivers to PC?
try this https://www.youtube.com/watch?v=Tm4LiABFKYo
---------- Post added at 01:18 AM ---------- Previous post was at 01:16 AM ----------
Shootarz said:
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 3860 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> cm.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
try this tutorial I happened the same and so solve it https://www.youtube.com/watch?v=1aNP0ImacUk

Categories

Resources