Related
Edit: Solution found look below!!!
As I posted in a different thread:
I managed to do it, but it was hackish
How I did it:
Used a terminal directly on the tablet, no adb.
I installed the acer chinese update. I 'dd'ed my old system and flexrom and rebooted. After that I checked for updates, and as luck had it, there was one. I tried it, but it failed half way through the procedure.
I rebooted again, then I 'dd'ed a boot.img on mmcblk0p2 from a 1.016 that matched my original system.img and flexrom.img. WITHOUT REBOOTING (I tried that before, it gives a bad kernel checksum and stops, but I assumed on update it would just patch if the file corresponds and re-sign), I then proceeded to do the update. It rebooted, entered recovery, and lo and behold, IT WORKED! So I'm 100% back to stock.
I would imagine that the same procedure would work when manually updating through recovery (using an extracted update.zip).
I used the kernel from here:
http://forum.xda-developers.com/showpost.php?p=14033507&postcount=27
EDIT: The kernel is stock for ACER_A500_1.016.05_COM_GEN1
Take a look at the thread linked below, get the 1.016.05_COM_GEN1 files (system, flexrom, and boot). If you are not offered an online update (System>About>Check for updates), you need the official update.zip from Acer. Extract the update.zip from the official Acer update THAT MATCHES YOUR FLEX VERSION using the XOR 12 method (see here - http://forum.xda-developers.com/showthread.php?t=1065360&page=20 - note in that post the link is for 03_COM_GEN1, NOT 05_COM_GEN1. For 04_COM_GEN1 and 05_COM_GEN1 see here - http://forum.xda-developers.com/showpost.php?p=14052165&postcount=184. For 03 and 04 you will need to find system.img, flexrom.img and boot.img, for 05 they are linked in the thread below).
EDIT: The thread with the images for ACER_A500_1.016.05_COM_GEN1 is here:
http://forum.xda-developers.com/showthread.php?t=1086785
EDIT: You might pull this off for other flex versions as well, but you would need all the files (system.img, flexrom.img, boot.img AND update.zip) from those versions.
PLEASE NOTE THAT THIS ONLY WORKS IF YOU HAVE THE OFFICIAL UPDATE.ZIP FOR YOUR SPECIFIC FLEX VERSION
Wow, I was about to try that!!!
I'll do that now and see how it goes.
Thanks mate!
EDIT: Worked!
I would expect that the reason an update fails on the Chinese one is that it tries to patch the kernel (which is different from the one expected). The update is a bunch of diffs and patches, and almost no full files, so it cannot be applied over anything but the right files.
Yes that is true. The old kermel checksum check was failing.
huxflux2003 said:
EDIT: Worked!
Click to expand...
Click to collapse
Glad to hear it Take that, you sneaky Acer bastards!
adancau said:
As I posted in a different thread:
I managed to do it though, but it was hackish
How I did it:
Used a terminal directly on the tablet, no adb.
I installed the acer chinese update. I 'dd'ed my old system and flexrom and rebooted. After that I checked for updates, and as luck had it, there was one. I tried it, but it failed half way through the procedure.
I rebooted again, then I 'dd'ed a boot.img on mmcblk0p2 from a 1.016 that matched my original system.img and flexrom.img. WITHOUT REBOOTING (I tried that before, it gives a bad kernel checksum and stops, but I assumed on update it would just patch if the file corresponds and re-sign), I then proceeded to do the update. It rebooted, entered recovery, and lo and behold, IT WORKED! So I'm 100% back to stock.
I would imagine that the same procedure would work when manually updating through recovery (using an extracted update.zip).
I used the kernel from here:
http://forum.xda-developers.com/showpost.php?p=14033507&postcount=27
Take a look at the thread, get the 1.016 files, system, flexrom, and boot, and try it.
Click to expand...
Click to collapse
Ahhhh a true milestone, well done.........
Nice work! Two questions:
Does the update work in the US?
I assume gingerbreak still works after the OTA update?
Thx
gingerbreak works
_motley said:
Does the update work in the US?
I assume gingerbreak still works after the OTA update?
Click to expand...
Click to collapse
A warning first: You DO NOT need to do this if you haven't installed the chinese update.zip (update.acer.zip) before, as that is the only one that changes kernels. Also, if you have anything other than ACER_A500_1.016.05_COM_GEN1, it's debatable if you want to do this (if you do read below), it might be better to wait for an official update.
The kernel above is stock for ACER_A500_1.016.05_COM_GEN1
So it works if you have ACER_A500_1.016.05_COM_GEN1 images, or are ok with changing your flex to that (in which case you would need to flash a system.img and a flexrom.img for ACER_A500_1.016.05_COM_GEN1, reboot, and then flash the kernel from the post above before heading off to recovery and updating - HOWEVER as far as I know no one has tried this, though IN THEORY it should work).
Gingerbreak still works, you can get root back after updating.
Just so I'm clear...
I'm at version 1.139.05 but I got here via the Chinese update.zip.
What do I need to do to get back to stock? Do I need to go back to my old system image and flexrom plus a new kernel?
Could someone post clearer instructions?
Thanks
adancau said:
A warning first: You DO NOT need to do this if you haven't installed the chinese update.zip (update.acer.zip) before, as that is the only one that changes kernels. Also, if you have anything other than ACER_A500_1.016.05_COM_GEN1, it's debatable if you want to do this (if you do read below), it might be better to wait for an official update.
The kernel above is stock for ACER_A500_1.016.05_COM_GEN1
So it works if you have ACER_A500_1.016.05_COM_GEN1 images, or are ok with changing your flex to that (in which case you would need to flash a system.img and a flexrom.img for ACER_A500_1.016.05_COM_GEN1, reboot, and then flash the kernel from the post above before heading off to recovery and updating - HOWEVER as far as I know no one has tried this, though IN THEORY it should work).
Gingerbreak still works, you can get root back after updating.
Click to expand...
Click to collapse
Thanks guys, I did restore using the Chinese update.zip last week and I am currently sitting at kernel 2.6.36.3 with flashed system img=Acer_A500_1.104.05_COM_GEN1, but with recovered Chinese kernel modules for wifi etc. I also flashed a flexrom.img from this build as well. I didn't flash the boot.img from this build, but was thinking about it until huxflux2003 reported the check-sum failure.
So, I am trying to decide what I am going to do. It sounds easy enough to get back to stock now, but I may wait for the official update next month that has 3.1. At this point, I suppose we are assuming that it will be a full update.zip that will work on any tablet (god I hope so). It's about time they gave us a full recovery image...I will be beyond disappointed if they don't. Let's also just hope we can still gain root easily after this.
One more question, if I use all the images from ACER_A500_1.016.05_COM_GEN1 that were posted, does this have to match what I had originally had in any shape or form? It sounds like since all the pieces are from the same build, everything will be fine regardless of what you had to begin with. Is this right?
Thx
To your last question - Theoretically yes, it should work, and I guess you don't need to match what you originally had. I can only speculate, logically though it would makes sense. You definitely need all the images to be from the same build (system+flexrom+boot.img). You also need the official update for that build.
heyoh said:
Just so I'm clear...
I'm at version 1.139.05 but I got here via the Chinese update.zip.
What do I need to do to get back to stock? Do I need to go back to my old system image and flexrom plus a new kernel?
Could someone post clearer instructions?
Thanks
Click to expand...
Click to collapse
To get back to stock you need the three images for your build - system, flexrom, and boot. If there is no online update available, you also need the update.zip for that build (extracted from an official acer update using the XOR 12 method - do a search).
Alternatively, I suppose you could switch to a new build for which you could find all the necessary files (but it hasn't been tried).
Flash system.img using dd. You might need to re-root. Reboot, flash flexrom.img. Reboot once more. Make sure your wifi works (you might need different kernel modules).
Look to see if there is an online update (Settings > About > Check for updates). If there is, cancel it. Flash boot.img on mmcblk0p2. DO NOT REBOOT.
If there was an online update available, now it's the time to perform it. After it's done you will get you back to stock 1.139.05.
If there isn't any update, make sure you have the update.zip on the root of your microSD. Turn off the tablet, then turn it back on holding the volume key closest to the power button. Do not let go of that button until you see some text in the corner. At that moment the update would begin. Once rebooted you will be back to stock.
Hope I've explained it better this time, and it works ok for you. If not, you need to go through the chinese update again. Good luck.
adancau said:
To your last question - Theoretically yes, it should work, and I guess you don't need to match what you originally had. I can only speculate, logically though it would makes sense. You definitely need all the images to be from the same build (system+flexrom+boot.img). You also need the official update for that build.
Click to expand...
Click to collapse
It worked for me too! Thanks again for the tip. I am now at the latest build and ahead of the US update schedule from what I can gather
It asked me to update after I flashed the ACER_A500_1.016.05_COM_GEN1 build system.img and flexrom.img. Even from the US it prompted just fine since I was on ACER_A500_1.016.05_COM_GEN1 build and not ACER_A500_1.104.05_COM_GEN1 as the former is what the differential patch targets.
I cancelled the update once I saw it presented and then blew on the boot.img from the ACER_A500_1.016.05_COM_GEN1 build. Then, without rebooting, I downloaded and applied the update (but with a little hiccup, see below). Now I am at Acer_A500_1.139.05_COM_GEN1 and didn't lose any user apps or settings etc.
Had a scary point though that I will share as it may help others. The first time I tried, the zip wouldn't downloadload and I was getting an HTTP 403 error. I cleared the systemupdater app and FWUpdateService data. I also killed the services and then I was stuck. Instead of conceding to reflashing the Chinese update.zip and starting over, I unzipped the Chinese update.zip and grabbed the boot.img from it. I then dd'ed that image back to the boot partition and rebooted again. It came back up and I this time I was able to do the system update successfully. Whew!
Followed instructions by OP and it worked perfectly! Back to stock and updated.
I think I'll be keeping these system images for next time I brick and have to flash the Chinese update.
Any chance of someone uploading the extracted update.zip for the new Acer_A500_1.139.05_COM_GEN1 so I can update manually using this method.
Thanks in advance
I used the above method to update to 1.139.04 from 1.016.04.
However my kernel is still 2.6.36.3-00001-gf991e5d instead of the 2.6.36.3 everyone else is reporting?
tianqi said:
I used the above method to update to 1.139.04 from 1.016.04.
However my kernel is still 2.6.36.3-00001-gf991e5d instead of the 2.6.36.3 everyone else is reporting?
Click to expand...
Click to collapse
If you directly flashed a 1.139.04 image your kernel has not been updated. You had to flash a 1.016.04 image, flexrom and boot, and then run the update.
You MIGHT have some luck regardless by running the update.zip now (I used it on mine one time when I updated like you did, and it seemed to work, but I have not noticed the kernel number). Be prepared to have to reflash if something goes wrong though.
I did reflash system, flexrom, and boot from 1.016.04...
Second time is still the same...
Kernel is still 2.6.36.3-00001-gf991e5d...
I need help! I need a stock, unmodified recovery partition image.
Anyone here with a vzw tab who DOES NOT yet have CWM installed?.
PLEASE contact me.
Thanks!
electron73 said:
I need help! I need a stock, unmodified recovery partition image.
Anyone here with a vzw tab who DOES NOT yet have CWM installed?.
PLEASE contact me.
Thanks!
Click to expand...
Click to collapse
I have one that hasn't been moded but have no idea how to get you what you want. PM me if you know how to download and send to you and I'll do my best to help.
I'll check my laptop at home tonight. I believe I kept my heimdall backup before flashing cwm
Sent from my DROID BIONIC using Tapatalk 2
Just checked, mightve deleted it. Sorry man
aximtreo said:
I have one that hasn't been moded but have no idea how to get you what you want. PM me if you know how to download and send to you and I'll do my best to help.
Click to expand...
Click to collapse
Oh that would be awesome! Are you rooted? Let me find the commands in the meantime, I read somewhere it's a simple one command in terminal to extract the recovery partition into a file on sd card...
WHAT AN ORDEAL !!!!
But in the end: SUCCESS!
I managed to get my tab updated with the Verizon OTA update.
The problem is definitely CWM !!! A rude awakening is in store for everyone with the P6800 CWM installed, because it a) fails to verify the checksum of OTA files correctly on the i815, b) it thinks the tablet is a P6800, so the OTA file fails to run if it assert checks for "SCH-i815" hardware AND lastly c) modem updates don't work because the device /dev/cdma_update doesn't exist, so the modem.bin firmware_update call fails !!!
In short, I had to fumble the OTA file apart and do the update manually in two runs:
First file, kick the checksum, hardware check and modem update out, then manually run the ZIP through CWM. The zip subsequently (LUCKILY) updated the stock recovery and overwrote CWM with a new fresh stock recovery.
Second file had everything kicked out BUT the modem udpate and LTE patch, so with the STOCK recovery this file ran through just fine, updated the modem and then applied the LTE delta patch.
Phew!!!
Of course I had to manually restore root after the update, had backed up with voodoo, auto restore failed, so terminal and hacking it was...
Now I have the tab running on clean stock FD01, baseband and LTE FD01, rooted and stock recovery.
No more CWM, no more "hacking" with the ROM until some dev finally releases a "correct" CWM and at least ANY factory ODIN image is available to bring the tab back to stock if needed!!!
Kinda sick of the non-support for this tab. So much going on for the Galaxy Note and pretty much every other device. I'm starting to regret having bought this "special" Verizon version
Awesome find and great to know for whenever ics does come out. Could you please post the recovery img you got?
Sent from my DROID BIONIC using Tapatalk 2
OK after getting so many responses I decided to just post everything here in hopes that it will help others, too:
All files are here:
http://www.mywo.org:88/XDA/sch-i815/index.php
Step by step procedure to update the Verizon Tab from ..FA02 to ..FD01 build IF YOU ARE stuck with CWM installed on your tab and the original OTA fails with errors:
Upload the SCH-I815_FA02c_To_FD01.1.zip to the INTERNAL(!) SD card. This is important because CWM contains a bug that will only allow you to install from ZIPs stored on the INTERNAL SD storage.
Upload the SCH-I815_FA02c_To_FD01.2.zip to the EXTERNAL(!) (micro SD) card. This is important, because after the factory recovery is restored, it will correctly (and only) look for ZIPs on the EXTERNAL card.
Best way just copy both files to both locations
Fire up CWM and do "install from ZIP" and select SCH-I815_FA02c_To_FD01.1.zip
It should run (takes a while) and eventually tell you all is done. BOOT the tab. It should boot fine but in system it will show the new Android build FD01 but the baseband (radio) will still be the "old" one.
Now press and hold power and vol up again until you see the default Samsung recovery menu. Choose install from ZIP and select SCH-I815_FA02c_To_FD01.2.zip. This will now upgrade the baseband only. When done, reboot and enjoy being back on the "factory upgrade path" with the tab.
I hope someone more savvy than me can "fix" CWM to work properly with VZW tabs (accept the checksum, not fail the check for "SCH-i815" and provide the correct /dev file links for radio upgrades). Until then, I recommend just leaving the tab as-is and not tinkering with the ROM. Not that there is any custom ROM available anyway :-(
I also pulled the NEW factory recovery image FD01_recovery.img with the following command:
dd if=/dev/block/mmcblk0p6 of=/sdcard/FD01_recovery.img bs=4096
So in case anyone with a botched recovery wants to restore factory (Samsung 3e) recovery. This was actually the reason I had to go through all this... There is NO factory recovery image ANYWHERE to be found. I can't believe that I should be the first one ever to post one?? Anyway, hope it will help
I'm still quite new here, so I do really appreciate every click on that "thanks" button
P.S. for tinkerers and devs I also uploaded the original, untouched OTA file (0559c0e4e08e.update_SCH-I815_FA02c_To_FD01.bin) as it came from Samsung or Verizon or whatever and ended up in the /cache partition.
THANK YOU!
Electron,
You sir, are a BOSS! Thank you so very much for doing the work, and sharing it. You just made things one hell of a lot easier on me, and anyone else that follows.
Regards,
-Rob
Also want to say thanks. You rock, dude. I wouldn't have known how to revert **** on my own.
Also, I feel like we need a sticky or something for sch-i815 owners to go to for device specific stuffs, especially since there is little knowledge/info out for this device.
Sent from my Galaxy Nexus using xda premium
hmm i only ever installed ROM manager ... but i did root it ... problem is ... now i don't have a CWM recovery to flash the file ... any ideas?
phigmeta said:
hmm i only ever installed ROM manager ... but i did root it ... problem is ... now i don't have a CWM recovery to flash the file ... any ideas?
Click to expand...
Click to collapse
You're in luck! You don't need to go through the whole ordeal because you do NOT have CWM! You can just update the regular intended way. Go into settings, about phone and then click check for system updates. If it presents you the OTA update, just do it the regular way.
My complicated "hack" is only necessary if you DO HAVE CWM installed.
Im sorry I did not explain well what my issue is.
I do not have CWM installed, however i did delete a few appilcations using titanium backup. This causes updates to not take. I would really like to just take it back to factory and start over (this time with less stupidity on my part)
I of course would assume that once its at factory i can then install updates again.
Right now when i try i get the "!" droid sign and a reboot
phigmeta said:
Im sorry I did not explain well what my issue is.
I do not have CWM installed, however i did delete a few appilcations using titanium backup. This causes updates to not take. I would really like to just take it back to factory and start over (this time with less stupidity on my part)
I of course would assume that once its at factory i can then install updates again.
Right now when i try i get the "!" droid sign and a reboot
Click to expand...
Click to collapse
Hey
OK unless someone can tell us how to "make" an ODIN flashable ROM for you, here is what I would do (and please don't get scared because it sounds a bit convoluted).
First, you need to be rooted. This is obviously the case.
IMPORTANT since you don't have CWM installed yet, SAVE your factory restore.img before proceeding, this saves you a lot of hassle later!
Open the android terminal, type su (accept the prompt) and then type (or copy/paste)
dd if=/dev/block/mmcblk0p6 of=/mnt/sdcard/factory_recovery.img bs=4096
Check that you have a "factory_recovery.img" file on your sd card now it should be about 8M big.
Now you're safe to install CWM from the forum, look for the other thread(s) where this is being discussed and follow the instructions for the P6800 "international" version with 3G. CWM Thread here:
http://forum.xda-developers.com/showthread.php?t=1613638&highlight=cwm&page=3
Then (thanks to nicduim!) there is a full factory (rooted) CWM image floating around on the forums here:
http://forum.xda-developers.com/showthread.php?t=1613638&page=6
Which I used to restore my tab to "almost factory" with the missing bloat apps back in place.
I have a copy on my server here: http://ww.mywo.org:88/XDA/sch-i815/ it's the "2012-05-06.22.48.58.ZIP"
unzip that and put the contents on your INTERNAL SD card in the folder clockwordmod. So on your internal SD you should have /clockworkmod/2012-05-06.22.48.58 and inside there the files boot.img, recovery.img etc.
Use CWM recovery to restore this backup. If you never used CWM before. Press power button and volume up and hold both until you see the menu screen with text. You can go up/down with the volume buttons (go slow, it's very laggy) and with the power button you "select" an option. Select the "restore from backup" option and point it to the only folder being offered, the 2012-05-06.22.48.58.
The restore takes a while, then reboot the tab. Now you're back to stock! Last thing you need to do is get rid of CWM again because in the end it's still a bit buggy and will prevent the OTA update from running properly.
Since you luckily have a backup of the factory recovery in form of that factory_recovery.img file, just install and open terminal again, type su and then type (or copy)
dd if=/mnt/sdcard/factory_recovery.img of=/dev/block/mmcblk0p6 bs=4096
This overwrites CWM with your original Samsung Android recovery.
Now you just reboot as usual, connect to the internet and wait until the popup message shows up that a system update is ready, accept it and enjoy
If you don't want to wait for the automatic OTA, you can also stop before killing CWM and use my convoluted 2-step manual update which will get you to the exact same condition as the official OTA.
Hope all this makes sense
I was already on stock FD01 when I tried installing CWM for the P6800 that's floating around here somewhere. Odin said it was a success, but it looks like it didn't take. I've done it a few times, but still ended up w/ the stock recovery. However, after reading through your thread, I do not see a /dev/cdma_update in my I815 either. Is it possible that my attempt to install CWM (although unsuccessful) wiped out this file, among others?
Right now, I'm still at stock FD01 (rooted) and everything seems to be working. When I tried doing an OTA update, it just tells me that I have the latest update and no newer update is available.
One other thing, if I have to, I only have the stock recovery right now since CWM didn't take, can I simply flash both zip's using the Samsung stock recovery to put everything back in stock?
SCH-I815_FA02c_To_FD01.1.zip
SCH-I815_FA02c_To_FD01.2.zip
AlpineMan said:
I was already on stock FD01 when I tried installing CWM for the P6800 that's floating around here somewhere. Odin said it was a success, but it looks like it didn't take. I've done it a few times, but still ended up w/ the stock recovery. However, after reading through your thread, I do not see a /dev/cdma_update in my I815 either. Is it possible that my attempt to install CWM (although unsuccessful) wiped out this file, among others?
Right now, I'm still at stock FD01 (rooted) and everything seems to be working. When I tried doing an OTA update, it just tells me that I have the latest update and no newer update is available.
One other thing, if I have to, I only have the stock recovery right now since CWM didn't take, can I simply flash both zip's using the Samsung stock recovery to put everything back in stock?
SCH-I815_FA02c_To_FD01.1.zip
SCH-I815_FA02c_To_FD01.2.zip
Click to expand...
Click to collapse
Oh wait, so you are saying that in "About device" your Android is 3.2
Baseband i815.04 V.FD01 I815FD01
and your Build number is already at HTJ85B.I815FD01.SCH-I815.I815FD01 ?
That would mean you are already updated. In this case, it should be pretty easy to fix your problem. Which apps did you delete with Titanium? I can back them up from my system and make them available for you. All you'd need to do is drop the backup files into your Titanium backups folder and then fire up titanium and restore them!
The /dev/cdma_update node is only required WITHIN CWM recovery, so that is nothing for you to worry about. The zip files above won't help you because they are incremental updates requiring your system to be at FA02, not FD01 !
Yes... I'm already in the latest update. I already backed up the bloatware using Titanium Backup before uninstalling. So I just need to restore them back in order to receive and apply OTA updates in the future?
Sent from my SPH-D710 using Xparent ICS Blue Tapatalk 2
Please Help
Hi. I'm rooted and removed all sorts of bloatware with Titanium. I did this a long time ago and did not back anything up because I'm used to running hardware with custom ROMs available, and not relying on OTA updates.
Since there aren't any custom ROMs for the i815, I'd like to get ready for the upcoming ICS update. To do so, I want to get FD01 loaded onto my device, but I can't update because I've apparently removed too much of the required bloatware.
Does anyone know WHAT pieces of bloatware I'd need to reinstall in order for the OTA update to apply? I'd assume I can restore them and then apply the update and re-root.
If anyone can help pinpoint what missing APKs might help, I'll give them a shot. And, to the extent I figure anything out, I'll repost here in the hopes that it helps someone else.
electron,
Your instructions worked ... thank you so much
@jkrell... the failed attempt at installing the update should return an error message(s). You just have to read through them until you find the culprit(s). Apparently I uninstalled a few odexed files that were needed. I couldn't update until i hunted them down and restored them.
I guess we all jumped at the opportunity to install the cwm recovery image, that we didn't even think about cmda updates....ooops. So far i had to do a complete factory restore after the update. I was getting soft bricked to the point where I had no choice. Good thing I sent all titanium backups to actual sd card, i was able to salvage 97% f my data..... with the exception of a few downloads i forgot to move.
Gamecih doesn't work anymore (either version). No more automative data hacks I'm not sure what's going on. I uninstalled adfree..used titanium backup to uninstall both versions and reinstalled both several times. Oh well.
It really sucks not having nandroid backups but it's not worth the trouble of having to do this everytime an OTA modem update gets pushed to my tab. Needless to say, I won't be odining the cwm based recovery image again.
I'm with the O.P. I wish i hadn't wasted my money on this tab. No true cwm for this tab, so no dev will ever waste thier time with this tab. The sch i815 will soon be forgotten about and some other tablet will be all the hype before summer ends....that's just how it is. 21 months left on my contract.... [email protected]#k my life. Lol
Thanks Smitty.
When I try to update, I just see the "!" logo and then the device reboots. Is there a log file somewhere I can look at to see what the errors are?
I hear ya on the gloom and doom, but this device has only been out for just over 3 months now. I'd expect a recovery and some custom ROMs to come eventually. I doubt I'll go the custom ROM route unless CyanogenMod is supported, because I have no complaints about the tablet's performance thus far. It's speedy, smooth and the battery lasts forever.
In my book, this is a great tablet and I'm satisfied with the purchase.
I've been trying to update from 4.1.2 to 4.2.2, but I deleted some stock apps and now the update is failing. I've tried flashing it manually and OTA, and various other things, but nothing has helped so far. Has anyone else had this problem?
The OTAs are for use with [size=+2]unmodified[/size] factory ROMs.
bftb0 said:
The OTAs are for use with [size=+2]unmodified[/size] factory ROMs.
Click to expand...
Click to collapse
I figured that out when I tried to update. I can't flash it either, so your post doesn't really help.
wipeout4wh said:
I figured that out when I tried to update. I can't flash it either, so your post doesn't really help.
Click to expand...
Click to collapse
My post tells you that you have the wrong expectation about what OTAs are capable of... and that you are probably the 200'th dude to come in here and say
"Wahhh! The OTA doesn't work on my heavily modified stock ROM!".
If you want it to work without exerting any mental effort, return the /system, boot, and recovery partitions back to 100% pure stock corresponding to whatever release your original ROM was based upon, and run the update. Then re-flash your recovery and re-perform all your /system mods, starting with a flash of the same root kit you started with.
Note that the the update you are contemplating also includes a bootloader update - performed the safest way possible (signature checking performed by the existing boot loader). Doing it the manual way (via fastboot) is quite dangerous, even for experts. If you have a 3g version there is also a radio update which also should not be attempted in any other way than via a pure stock OTA install including use of a stock recovery.
Make a full Nandroid backup before you begin anything - and get a copy of that backup off of the tablet as well as a failsafe measure. If you screw things up moving forward, at least you will be able to start over from where you are right now.
If you have been operating using best practices, you should already have a nandroid backup of the pure-stock /system & boot images. TWRP allows you selectively restore individual partitions. Few users seem to know how to actually make a backup of stock recovery partitions, but you can get that out of oldblue910's archive site - find the link in the OTA thread.
good luck
wipeout4wh said:
I figured that out when I tried to update. I can't flash it either, so your post doesn't really help.
Click to expand...
Click to collapse
He's telling you the plain and simple truth. Want the OTA- as it stands, you're out of luck. Either return to stock and then flash the OTA, or flash the 4.2.2 factory image. That's it. Nothing more. That anyone even bothered to answer this uselessly redundant thread is a miracle in and of itself.
Sent from my Nexus 7 using Tapatalk HD
Hi Guys.
I decided to create a new thread because I simply can't find an answer to my specific issue, I know that tons of people are getting the software interrupted just like me, but I'm not willing to do a full wipe again, just to update from MF3 to MK2.
Last month I was stuck on 4.2.2 because I was root, so I decided to install the Factory 4.2.2 files losing my files and data just to be able to upgrade to 4.3 so I can finally could buy the Samsung Gear, so I did it, I installed Factory Rom, I did the Sideload update to 4.3 and everything went great, no errors that I could remember, my S4 was fully reset, so there was not even a single trace of previous Android files. Now this is what is weird, I did the same for a co-worker that asked me to do it, because he was having issues with freezings and errors, so I did the exact procedure that I did on mine, for our surprise as soon as he arrived at his home that day, he received a notification that there was a new update, that's was the same day that AT&T released the MK2 update, so he took the update without issues.
The next day he told me about it and since then (I think almost 3 weeks now) I've been trying to see if my phone gets the MK2 update and nothing, every day I check and every day I get the almost immediate Software Interrupted Message. I've been searching and reading a lot of threads and info around the web and I can't manage to find a single post that tells me how to update from MF3 to MK2, via Sideload, Odin or any other possible way, the only way that I have read is to download the Full MK2 Rom that has posted here a lot of times, but just for curiosity I tried to use it and it doesn't work unless you are on 4.2.2.
So, as you can see, I have tried to just do the update, trying to find the small (28 MB) file that should update from MF3 to MK2, but there is no place to be found, as you know, Kies doesn't work either, so if my phone keeps doing the Software interrupted thing that I've been getting since Summer and that I thought that it was something related to root, I won't be able to do this update and I'm afraid that Kit Kat update either. So 2 things, Does anybody has any other idea that doesn't involve resetting the phone? ( Literally took me a whole day to put back everything as I had it before, without Root and Titanium Backup there is no easy restore on this phones) and Second, Why do you think I'm still getting the software Interrupted thing, when the phone was completely reset just like my co-worker's?
Thanks in advance.
After posting this, I saw for this other Thread (That I swear that I didn't see it before) that was posted last night http://forum.xda-developers.com/showthread.php?t=2573080, but looking at the file that needs to be downloaded is the Full 728 MB Rom, and I'm worried that it may erase all my Data if I flash this update, so I will wait for somebody to confirm that it works and just update without wiping.
erasat said:
After posting this, I saw for this other Thread (That I swear that I didn't see it before) that was posted last night http://forum.xda-developers.com/showthread.php?t=2573080, but looking at the file that needs to be downloaded is the Full 728 MB Rom, and I'm worried that it may erase all my Data if I flash this update, so I will wait for somebody to confirm that it works and just update without wiping.
Click to expand...
Click to collapse
Try the file from post #657 in this thread http://forum.xda-developers.com/showthread.php?t=2498897&page=66
Sideload the big file.
It won't wipe out your existing data... but if you get errors with the process, you will need to do a full wipe or flash back to stock first.
I would do this, if I were you:
1. Backup everything with Titanium Backup
2. Odin back to stock MF3
3. Root MF3, and put SuperSU in survival mode
4. Restore apps + data (no system apps) with Titanium Backup
5. Sideload to MK2
6. Manually restore your system settings, ringtones, whatever.
7. Relax
joeybear23 said:
Sideload the big file.
It won't wipe out your existing data... but if you get errors with the process, you will need to do a full wipe or flash back to stock first.
I would do this, if I were you:
1. Backup everything with Titanium Backup
2. Odin back to stock MF3
3. Root MF3, and put SuperSU in survival mode
4. Restore apps + data (no system apps) with Titanium Backup
5. Sideload to MK2
6. Manually restore your system settings, ringtones, whatever.
7. Relax
Click to expand...
Click to collapse
On some posts in a different thread, this person said that they're on MJ9, that's why I gave them the link to the small update file. Your way is the way that I'd do it if they are indeed on MF3.
dwanhala said:
On some posts in a different thread, this person said that they're on MJ9, that's why I gave them the link to the small update file. Your way is the way that I'd do it if they are indeed on MF3.
Click to expand...
Click to collapse
If he's on MJ9 and thinks he's on MF3, this whole thing is not going to end well...
joeybear23 said:
If he's on MJ9 and thinks he's on MF3, this whole thing is not going to end well...
Click to expand...
Click to collapse
No, i'm very sure on what I am and what I need to do, only issue is that so far none of the files were for MJ9 updated phones.
dwanhala said:
Try the file from post #657 in this thread http://forum.xda-developers.com/showthread.php?t=2498897&page=66
Click to expand...
Click to collapse
Wow, coming here daily and reading most of the threads (Including that one) I don't know how I missed that, but man, THANKS A LOT, I went to that thread and downloaded the file and YES, this one is the real deal for the updated MJ9 guys, it sideloads perfectly and now I'm still at the Android is Upgrading screen but by experience I'm confident that it was updated perfectly, thanks a lot.
joeybear23 said:
Sideload the big file.
It won't wipe out your existing data... but if you get errors with the process, you will need to do a full wipe or flash back to stock first.
I would do this, if I were you:
1. Backup everything with Titanium Backup
2. Odin back to stock MF3
3. Root MF3, and put SuperSU in survival mode
4. Restore apps + data (no system apps) with Titanium Backup
5. Sideload to MK2
6. Manually restore your system settings, ringtones, whatever.
7. Relax
Click to expand...
Click to collapse
I too am stuck on MF3 no matter what I try doesn seem to work, sideload mf3-mj9, odin back to stock then reroot. I keep getting the error 7. I'm new to this whole thing but I've spent hours reading up on all of this. I tried this option above it didnt work either.
So, the other day, as samsung was pushing more bloat to my phone, I decided I had had enough Redit told me I could just delete most things from root, I did so by following the instructions from a google search of how-to-root-and-flash-cwm-recovery-on-sprint-galaxy-s4-on-android-4-3-tutorial (except, of course, the back up part)
then, without paying attention to the list of removable apps, I took out Samsung hub, And then the problems start. The phone still works: Except every second or so, i get told that the hub has stopped. The phone isn't bricked, but it is basically worthless with the message popping up constantly.
According to my settings, everything is still stock (L720VPUFNAE) Although I think just rooting it was enough to pop the Knox bubble. I'm not working on getting that rom to try to re-flash back to stock (I thought i had did this over night, but it seems like i had slightly different roms when I was doing this early in the morning)
I also tried installing the Samsung Hub apk, but I get an error stating that X app wasn't installed. I have not been able to find a source for this app while googling.
I've tried finding a custom rom to use, but most of the ones I THINK are good/will work, don't install via odin, and for some reason when I try to boot into recovery, it just sits indefinitely @ the samsung galaxy screen.
Am I just stressed and frustrated, or am I truly hosed?
Edit: I'm currently working through http://forum.xda-developers.com/showthread.php?t=2307531 as my next attempt
Edit: for some reason Philz recovery isn't ever entering a recovery mode for me, it just sides @ the samsung screen forever
Akuthia said:
blablabla I deleted something what I shouldn't and now my phone is faulty, but I do not want/can reflash using Odin and CWM :crying::crying::crying:
Click to expand...
Click to collapse
You still can install Mobile Odin from google Play, copy ROM to SD card and try to flash it in that way...
spamtrash said:
You still can install Mobile Odin from google Play, copy ROM to SD card and try to flash it in that way...
Click to expand...
Click to collapse
I get it, i deserve the sarcasm, I broke rule 1 of upgrades. (one of) the problems I'm having though is finding the right file to flash to. Just looking for a little bit of advice as to what files I need to get back to " Normal" I know I should be able to flash to another rom, why when I use Philz Recovery it doesn't do what it's supposed to, is beyond me right now. Odin mobile requires the PDA file, correct? That seems fine to getting back to stock, but most of the custom roms I've found or are at least interested in are just files that are installed via recovery...which for some reason I don't have access too, right?
Akuthia said:
That seems fine to getting back to stock, but most of the custom roms I've found or are at least interested in are just files that are installed via recovery...which for some reason I don't have access too, right?
Click to expand...
Click to collapse
Correct. If I'd be you, I'd go to sammobile.com, and I'd start from full stock flash. It shall restore recovery. It it would work - you'd be OK to go with custom.
spamtrash said:
Correct. If I'd be you, I'd go to sammobile.com, and I'd start from full stock flash. It shall restore recovery. It it would work - you'd be OK to go with custom.
Click to expand...
Click to collapse
Ok, Sammobile has been efforting for about an hour. Has an hour to go. I also got CWM and am going to see if I can flash a rom with it. Transfer of those files is taking a while as well.
Akuthia said:
Ok, Sammobile has been efforting for about an hour. Has an hour to go. I also got CWM and am going to see if I can flash a rom with it. Transfer of those files is taking a while as well.
Click to expand...
Click to collapse
Got back to stock. Text messages gave me a fright for a bit was sending me a message they were undeliverable via another code text # one of those 4 or 5 digit things)
Akuthia said:
Got back to stock. Text messages gave me a fright for a bit was sending me a message they were undeliverable via another code text # one of those 4 or 5 digit things)
Click to expand...
Click to collapse
Good. Now, a small lesson for the future, if I can:
if you want to remove something, DO NOT delete software, use Titanium Backup and freeze apk first instead.
This will give you opportunity to check if you have frozen something important. :good:
spamtrash said:
Good. Now, a small lesson for the future, if I can:
if you want to remove something, DO NOT delete software, use Titanium Backup and freeze apk first instead.
This will give you opportunity to check if you have frozen something important. :good:
Click to expand...
Click to collapse
Thats the thing, i HAD made a backup in titanium of all my system apps, just so i could roll it back, but for some reason, it wasn't listed when the fan got hi by you know what.
Akuthia said:
Thats the thing, i HAD made a backup in titanium of all my system apps, just so i could roll it back, but for some reason, it wasn't listed when the fan got hi by you know what.
Click to expand...
Click to collapse
I DID not mentioned BACKUP.
I mentioned FREEZING.
Backup is another copy, which you may, or may not install.
FREEZE is that all files are present, but the application is not listed in system.