Hey guys, so I have a note 3 n9005,which i had rooted previously. This morning, I tried to flash the new touchwiz kitkat firmware via Odin and failed. Now the phone wouldn't boot up, but I an able to make it into the download mode. I have tried flashing several firmwares but neither of them works, I also had cm11 installed, so odpnt know f the bootloader has been updated or not...
So of anybody could please help me with this, that would be greatly appreciated
i have excatly the same problem tried to update s9005 via odin hong kong version to german 4.4.2 and now wont boot, odin fails only 20 seconds in read so many threads would also like to see some solutions to op.
CaptaiinCaveman said:
Hey guys, so I have a note 3 n9005,which i had rooted previously. This morning, I tried to flash the new touchwiz kitkat firmware via Odin and failed. Now the phone wouldn't boot up, but I an able to make it into the download mode. I have tried flashing several firmwares but neither of them works, I also had cm11 installed, so odpnt know f the bootloader has been updated or not...
So of anybody could please help me with this, that would be greatly appreciated
Click to expand...
Click to collapse
You also need to add some of the stuff it is written in download mode and the log in Odin when in fails. If you went to 4.4.2 on N9005 you can not return to 4.3 (which you should have read by now, there are only 200 posts in 50 threads about it). What kind of N9005 was yours (16/32/64GB), what region/CSC?
xclub_101 said:
You also need to add some of the stuff it is written in download mode and the log in Odin when in fails. If you went to 4.4.2 on N9005 you can not return to 4.3 (which you should have read by now, there are only 200 posts in 50 threads about it). What kind of N9005 was yours (16/32/64GB), what region/CSC?
Click to expand...
Click to collapse
I flashed the DBT FW again with this pit file created by HSDPilot http://forum.xda-developers.com/showpost.php?p=50614669&postcount=77.
It worked and lash was complete now however i am stuck in SAMSUNG logo after restart.
ANy help?
solution
newapostlenew said:
I flashed the DBT FW again with this pit file created by HSDPilot http://forum.xda-developers.com/showpost.php?p=50614669&postcount=77.
It worked and lash was complete now however i am stuck in SAMSUNG logo after restart.
ANy help?
Click to expand...
Click to collapse
hi i followed your instructions afte having the same problem.
once it was flashed and at the samsung logo
i took battery out, replaced it and started phone in recovery mode. go to wipe factory reset
then reboot
mine worked and is ok .
CaptaiinCaveman said:
Hey guys, so I have a note 3 n9005,which i had rooted previously. This morning, I tried to flash the new touchwiz kitkat firmware via Odin and failed. Now the phone wouldn't boot up, but I an able to make it into the download mode. I have tried flashing several firmwares but neither of them works, I also had cm11 installed, so odpnt know f the bootloader has been updated or not...
So of anybody could please help me with this, that would be greatly appreciated
Click to expand...
Click to collapse
darkman13 said:
i have excatly the same problem tried to update s9005 via odin hong kong version to german 4.4.2 and now wont boot, odin fails only 20 seconds in read so many threads would also like to see some solutions to op.
Click to expand...
Click to collapse
Do either of you have a 16 GB version?
Hi All,
My problem :
I wanted to install the official kitkat rom but I made a big mystake : I took N900 files instead of N9005...
After that I successfully installed the right bootloader and CWM.
I installed some cuustom roms but the setupwizard crash at the last step
I tried to flash the complete official 4.4.2 rom but odin failed with message on the phone : "ODIN : invalid ext4 image"
Anybody has any idea to help me ?
hi guys i manage to fix it, well mine anyway worked by flashing the pit i found on xda and selecting repartion on odin 3.7 along with german 4.4.2 to my n9005 from Hong Kong, re booted and done a factory reset via volume button also wiped cache and re started and it came back alive on the selected german rom 4.4.2. hope it hels others. ps my note 3 was from hong kong n9005 32gb
xclub_101 said:
You also need to add some of the stuff it is written in download mode and the log in Odin when in fails. If you went to 4.4.2 on N9005 you can not return to 4.3 (which you should have read by now, there are only 200 posts in 50 threads about it). What kind of N9005 was yours (16/32/64GB), what region/CSC?
Click to expand...
Click to collapse
hey, i wasnt trying to downgrade, i was going from cm11 to official 4.4.2. i've got a 32gb model from france i believe (the box has french written all over it so do the manuals)
newapostlenew said:
I flashed the DBT FW again with this pit file created by HSDPilot http://forum.xda-developers.com/showpost.php?p=50614669&postcount=77.
It worked and lash was complete now however i am stuck in SAMSUNG logo after restart.
ANy help?
Click to expand...
Click to collapse
dude, you are god thank you so much for that, working perfect now
xclub_101 said:
You also need to add some of the stuff it is written in download mode and the log in Odin when in fails. If you went to 4.4.2 on N9005 you can not return to 4.3 (which you should have read by now, there are only 200 posts in 50 threads about it). What kind of N9005 was yours (16/32/64GB), what region/CSC?
Click to expand...
Click to collapse
After installing DBT NB4 FW ( or with Polish NB3 FW) my LTE speeds become almost 0.
I tried multiple installs.
Any guidance?
Quick tip: Uninstall KIES.
Kies is like a big brother.
Use ODIN 1.85 and tick update phone bootloader. That's how I fixed mine. The other versions of Odin wouldn't let me update bootloader.
Of course, before you do this Flash/wipe data in recovery mode.
But uninstalling KIES solved my issue.
Sent from my SM-N9005 using Tapatalk
Related
Hey guys. Ive had a note 3 before in the past and have used the Root DelaVega to root successfully. This was early in the year. I sold my old note 3 for an HTC One. Well today i traded my HTC One back for a note 3 as i missed the Note 3. As soon as i came home i attempted to use the Root DelaVega method to foot (just like i did before) and immediately it failed.
I have been stuck on a screen saying "firmware update encountered an issue - select recovery in Kies" so i tried Kies 3.2 however it says my device is not compatible. Come to find out after doing research (talking to the original owner i traded my HTC One for) the Note 3 i have is on the latest version of KitKat 4.4.2 that is not compatible with the Root DelaVega method or any root method - so i screwed that up. I can successfully boot in and out of download mode. Ive tried to flash N900XXUDNA6 4.4.2 in Odin several times, it begins then fails almost immediately and the bar on the phone itself (in download mode) begins then freezes shortly after beginning. Ive also tried to flash N900XXUDNC1 JellyBean thru odin and get the same results - almost immediately fail and the blue status bar on the phone freezes when it barley begins. What else can i do??? am i totally screwed? Ive been researching and trying to fix this for 6 straight hours now! My gf is about to kill me for being online so long Is there anything i can do at this point? Am i stuck.
Do you know what Region the phone was originally? I had a similar issue and I had to get the Hong Kong (in my case) version of a stock ROM and flash that to get things working again. Not all partitions are the same - you might need a PIT file to match your original region and then flash the ROM.
What info do you get in DL mode?
Journyman16 said:
Do you know what Region the phone was originally? I had a similar issue and I had to get the Hong Kong (in my case) version of a stock ROM and flash that to get things working again. Not all partitions are the same - you might need a PIT file to match your original region and then flash the ROM.
What info do you get in DL mode?
Click to expand...
Click to collapse
Yes the phone is for AT&T so it's US. When I go into DL mode Knox counter is still 0x0. Is there a certain firmware I need then to match with the AT&T model? Or a pit?
jthornton71707 said:
Yes the phone is for AT&T so it's US. When I go into DL mode Knox counter is still 0x0. Is there a certain firmware I need then to match with the AT&T model? Or a pit?
Click to expand...
Click to collapse
Go to Sammobile and see if you can find the version you had, sounds like an older JB if kingo app didn't trip Knox. Reflash that using ODIN.
I don't know if there was a problem with American bootloader, see if there's an AT&T Note 3 forum. Might find answers there...
jthornton71707 said:
Hey guys. Ive had a note 3 before in the past and have used the Root DelaVega to root successfully. This was early in the year. I sold my old note 3 for an HTC One. Well today i traded my HTC One back for a note 3 as i missed the Note 3. As soon as i came home i attempted to use the Root DelaVega method to foot (just like i did before) and immediately it failed.
I have been stuck on a screen saying "firmware update encountered an issue - select recovery in Kies" so i tried Kies 3.2 however it says my device is not compatible. Come to find out after doing research (talking to the original owner i traded my HTC One for) the Note 3 i have is on the latest version of KitKat 4.4.2 that is not compatible with the Root DelaVega method or any root method - so i screwed that up. I can successfully boot in and out of download mode. Ive tried to flash N900XXUDNA6 4.4.2 in Odin several times, it begins then fails almost immediately and the bar on the phone itself (in download mode) begins then freezes shortly after beginning. Ive also tried to flash N900XXUDNC1 JellyBean thru odin and get the same results - almost immediately fail and the blue status bar on the phone freezes when it barley begins. What else can i do??? am i totally screwed? Ive been researching and trying to fix this for 6 straight hours now! My gf is about to kill me for being online so long Is there anything i can do at this point? Am i stuck.
Click to expand...
Click to collapse
Hi mate,
if you are stuck, maybe you can try this.
http://forum.xda-developers.com/show....php?t=2701062
it's a way to unbrick your software.
and if the older owner of your N3 said it's on the latest firmware of kitkat.
maybe your problem is the firmware in the sammobile were before the firmware you have install on your device via OTA update.
Yours firmware came throw out via OTA update and with some reason you can't see any latest firmware USA N900A in sammobile.
try the method in the link and reply if you have been successful.
cumps
Ik Knox is 0×0,then u can try samsung service centre ?
Sent from my SM-N900 using XDA Premium 4 mobile app
Hi guys,
I've wrote another thread with no response. Lemme ask like this:
i9505 with 4.3, want to flash to 4.4.2. Problem:
I can't flash any firmware, not by KIES 3 or ODIN. Both give me errors, KIES 3 saying S4 is disconnected and ODIN failing everytime, with and without pit file. Switched USB ports, KNOX is 0x0, System Status CUSTOM? Never touched it (branded).
Phone is working fine in the meantime.
Any help?
Anybody? At least tell me I can reflash the phone again...
slit said:
Hi guys,
I've wrote another thread with no response. Lemme ask like this:
i9505 with 4.3, want to flash to 4.4.2. Problem:
I can't flash any firmware, not by KIES 3 or ODIN. Both give me errors, KIES 3 saying S4 is disconnected and ODIN failing everytime, with and without pit file. Switched USB ports, KNOX is 0x0, System Status CUSTOM? Never touched it (branded).
Phone is working fine in the meantime.
Any help?
Click to expand...
Click to collapse
Which firmware was the latest on your phone and which one did you try to flash?
Your phone has got an branding, right? Do you want to debrand it or just to update it? Did you want to update with a branded firmware?
What does Odin exactly day in the log?
More information please, then we can help you better.
Gesendet von meinem GT-I9505 mit Tapatalk
DarkerTimes said:
More information please, then we can help you better.
Gesendet von meinem GT-I9505 mit Tapatalk
Click to expand...
Click to collapse
Thanks DarkerTimes,
My firmware is i9505XXUEMK9 ver 4.3 Vodafone Spain branded.
I just want to update it to official Vodafone Spain 4.4.2 KitKat , OTA doesn't work anymore because it says my device is modified (which it isn't, at least by me?)
I can't use ODIN anymore because the phone doesn't enter download mode when I press down+menu then power, it used to a few days back tho. This is weird. So I can't tell you what ODIN says, although I remember saying something about bad partition thus I've tried flashing it when download mode worked with and without pit file without results. ODIN always told me FAIL!
Also, SDcard or system file is getting weird these days, it rescans whole library of music and Winamp crashes everytime. Reinstalled it and now it seems to work... storage chips going south?
slit said:
Thanks DarkerTimes,
My firmware is i9505XXUEMK9 ver 4.3 Vodafone Spain branded.
I just want to update it to official Vodafone Spain 4.4.2 KitKat , OTA doesn't work anymore because it says my device is modified (which it isn't, at least by me?)
I can't use ODIN anymore because the phone doesn't enter download mode when I press down+menu then power, it used to a few days back tho. This is weird. So I can't tell you what ODIN says, although I remember saying something about bad partition thus I've tried flashing it when download mode worked with and without pit file without results. ODIN always told me FAIL!
Also, SDcard or system file is getting weird these days, it rescans whole library of music and Winamp crashes everytime. Reinstalled it and now it seems to work... storage chips going south?
Click to expand...
Click to collapse
Hi ,
step by step
Download mode , you said I press down+menu then powe I do it the 3 of them at the same time
Before using Odin kill all kies processes ( task manager), make sure no one is running in the background....
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Use pit file.
- Try another computer.
from this thread http://forum.xda-developers.com/showthread.php?t=2265477
try with a different tar file , try for example the PHE unbranded version of firmware for Spain
http://www.sammobile.com/firmwares/1/?model=GT-I9505&pcode=PHE#firmware
Regarding your sdcard ...maybe so much flashing left orphan files all over a good flashing should clear that problem
Hi MAX 404
thanks for your reply
I don't have KIES installed now, I've removed it after a couple fails last week... I've tried everything the guide says beforehand, I've flashed a previously owned S2 a lot of times before. Cable is samsung original, tried different USB ports and my laptop with no success.
Also, how can do a good flashing to clear that SD behaviour? Lost here.
SOLVED! It seems I have a ton of USB ports wrecked EXCEPT one. This worked so far so good.
Hi everyone,
This is my first post and I hope that I am in the right section.
As per info in the thread title, I have a Malaysian Samsung Galaxy Note 3 updated to the last available firmware 4.4.2
I am trying to flash Lollipop with Odin (i followed all the instructions in the guide, literally step by step).
I have tried with the italian Lollipop update branded Vodafone, but Odin always failed and the phone was soft bricked.
I have reinstalled the original malaysian firmware 4.4.2 that i had prior this attempt. phone booted ok and worked perfectly fine.
Then i downloaded the lollipop firmware from poland, this thime odin completed the process and gives me a pass. but the phone goes in boot loop (samsung logo at booting never goes away). I have tried to reboot in recovery mode and wipe the cache. but still boot loop.
Would anyone be so kind to explain what i am doing wrong and how i could install lollipop on my malaysian galaxy note 3?
Any help would be much appreciated.
Luc81
Wipe all before flash lollipop.
Joku1981 said:
Wipe all before flash lollipop.
Click to expand...
Click to collapse
Thanks,
actually I have just managed to flash it correctly about 1 hour ago. i didn't need to wipe my data. Now it works properly.
Thanks anyway for your help!
hows your experience ?
just let us know what was the mistek, so others wont have to ask the same question again ...hehehe
all the best!
note 3 lolipop(Malaysia) N9005
Guys good news because this morning when I was checking my software update ... Thru Ota is about 860mb and thru keis 3 is about 1.3gb. Took me couple hours to download and about 1hour ++ to install. Booting up took some time and luckily everything is working fine for the time being.
Anyone updated and how's the battery draining issue.
i try update my note3 using kies3, it confirmed lollipop 5.0 available to update, but unfortunately my note3 repeatedly crash during upgrade and window on kies top up said "PC cant recognized my phone". Maybe cause of my knox warranty void 0x1 (trip). i hack on local C:\Users\YOUR NAME\AppData\Local\Temp and get copy of *.zip files (N9005DXUGBOD1_N9005OLBGBOD1_HOME.zip). It was lollipop firmware version for malaysia. Upgrade it using Odin and succesfull installed.
Lolipop
I was having the same issue while updating thru keis. So I downloaded it thru OTA. Battery sucks after lolipop. If you are facing any issue just send me a mail
I have tried to flash the Android 5.0.1 stock firmware N910FXXU1BOC3 on my Note 4 N910F and I'm getting some error in Odin when it's writing the hidden.img.ext4 and failing. On the device, in Download Mode i see the error message volume size is too big.
Right now i'm on Android 4.4.4 N910FXXU1ANK4.
First thought was that i left Reactivation Lock on and saw a bunch of other threads where it says that this might be the main issue as I am flash a different CSC Region ROM. I managed to get back to N910FXXU1ANK4 after the failed flash of N910FXXU1BOC3 with Kies3 and Emergency re-initialization (thank you Samsung for finally doing something useful with Kies). I disabled the reactivation lock and attempted again to flash N910FXXU1BOC3 but failed with the same error.
After some searching, i found that the issue might be because i have to re-partition the device in order to fit the new partiton sizes for Android 5.0.1.
This should be done with the Odin option to Re-partition but that requires a PIT file in order to have the re-partition information.
I have looked into the md5 archive for the N910FXXU1BOC3 ROM and initial 5.0.1 release for N910F N910FXXU1BOB4 ROM but I could not find a PIT file in order to re-partition.
Now my question is, when going from Android 4.4.4 N910FXXU1ANK4 to Android 5.0.1 N910FXXU1BOC3, do I have to re-partition with Odin, and if so, where do I get the correct PIT file ?
Thanks.
lolozaur said:
I have tried to flash the Android 5.0.1 stock firmware N910FXXU1BOC3 on my Note 4 N910F and I'm getting some error in Odin when it's writing the hidden.img.ext4 and failing. On the device, in Download Mode i see the error message volume size is too big.
Right now i'm on Android 4.4.4 N910FXXU1ANK4.
First thought was that i left Reactivation Lock on and saw a bunch of other threads where it says that this might be the main issue as I am flash a different CSC Region ROM. I managed to get back to N910FXXU1ANK4 after the failed flash of N910FXXU1BOC3 with Kies3 and Emergency re-initialization (thank you Samsung for finally doing something useful with Kies). I disabled the reactivation lock and attempted again to flash N910FXXU1BOC3 but failed with the same error.
After some searching, i found that the issue might be because i have to re-partition the device in order to fit the new partiton sizes for Android 5.0.1.
This should be done with the Odin option to Re-partition but that requires a PIT file in order to have the re-partition information.
I have looked into the md5 archive for the N910FXXU1BOC3 ROM and initial 5.0.1 release for N910F N910FXXU1BOB4 ROM but I could not find a PIT file in order to re-partition.
Now my question is, when going from Android 4.4.4 N910FXXU1ANK4 to Android 5.0.1 N910FXXU1BOC3, do I have to re-partition with Odin, and if so, where do I get the correct PIT file ?
Thanks.
Click to expand...
Click to collapse
hi,
i have a N910F.. When i went from stock Android v 4.4.4 to Lollipop .. German Rom.. BOB4 and after that again to BOC3 I did not repartion anything. in fact repartion must be untick , I only made sure that auto reboot was ticked and F. Reset Time ticked then, place the tar/(md5 )file in AP section of Odin. Switch phone off, boot into download mode, connect phone via usb and wait for blue color to light up ID:COM box (above auto reboot) check if everything is connected and correct boxes ticked and then flash.( see screenshot ) After flash your phone will "try" to boot up but will optimise apps first. This can take some time (my case about 10 min? or so)
Plse take note that i am referring from stock Rom v4.4.4 to stock Lollipop
v 5.0.1 Also you only flash the one file....... "tar"/(md5 ) thats all.
good luck
willcor said:
hi,
i have a N910F.. When i went from stock Android v 4.4.4 to Lollipop .. German Rom.. BOB4 and after that again to BOC3 I did not repartion anything. in fact repartion must be untick , I only made sure that auto reboot was ticked and F. Reset Time ticked then, place the tar/(md5 )file in AP section of Odin. Switch phone off, boot into download mode, connect phone via usb and wait for blue color to light up ID:COM box (above auto reboot) check if everything is connected and correct boxes ticked and then flash.( see screenshot ) After flash your phone will "try" to boot up but will optimise apps first. This can take some time (my case about 10 min? or so)
Plse take note that i am referring from stock Rom v4.4.4 to stock Lollipop
v 5.0.1 Also you only flash the one file....... "tar"/(md5 ) thats all.
good luck
Click to expand...
Click to collapse
Thank you for the reply, thinking back I don't think i tried to flash BOB4 first and then BOC3. I will try this today and come back with some feedback.
lolozaur said:
Thank you for the reply, thinking back I don't think i tried to flash BOB4 first and then BOC3. I will try this today and come back with some feedback.
Click to expand...
Click to collapse
hi ,
i personally , don't think it will make any difference or matters,
if you flash the one or the other ..but hey ..who knows ..?
Only reason ,i flashed BOB4 as it was the first Lollipop available and BOC3 was a later date ( March 2015 )
good luck
I have the similar issue. KK and BOB4 roms work and install perfectly. however I am having the same issues while installing BOC3 rom be it Stock or Custom.
So I finally managed to solve the issue. Seems that the image I was downloading from Sammobile was not that good.
I was trying to install N910FXXU1BOC3_N910FVFG1BOC2_CNX - Romania Vodafone. I was unable to install it no matter what I tried.
I was able to install N910FXXU1BOC3_N910FTPD1BOC1_TPD - Netherlands unknown, without any issues.
Something that i noticed is that when loading the tar with issues in Odin, total binary size was shown as 0 mb, while on the Netherlands tar file it was showing 3.3gb.
Also the tar sizes where a bit strange : RO CNX 3.6gb - NL TDP 3.4gb. So I would imagine that extra 200mb might be an issue for the partition size (suspecting bloatware maybe?).
Long story short, the tar file I was trying was the issue and downloading a different CSC file solved this for me.
Also, I tried an advice from the forum, where you extract the recovery.img and convert to tar and first flash that tar before the ROM, but that did not work in this case.
Thank you for the replies and support.
Does it void the warranty ? I am also on 4.4.4 ANK version and want to update fo 5.0.1 BOC3.
Sent from my SM-N910F using XDA Free mobile app
I installed the BOB4 like said willcor and do an antutu and, I know that it are subjective information, but I was exhausted of see the Meizu above our fairy note 4 (including with the last 4.4.4), but now, I will sleep much more well than yesterday...
Beko68 said:
Does it void the warranty ? I am also on 4.4.4 ANK version and want to update fo 5.0.1 BOC3.
Sent from my SM-N910F using XDA Free mobile app
Click to expand...
Click to collapse
If you're talking about knox (hehe of course, what else) knox still 0x0 after installation...
Doing this kept my knox counter at 0x0, but I did not root or install any custom recovery.
Slightly off topic but I would stay away from BOC3. Many people I know have had problems with BOC3 Firmware.
I am going to be re-flashing BOC3 when I get back home... I must admit when I flashed BOC3 I didn't do a fresh wipe before flashing it so might have been my problem.
Have you wiped your phone before flashing the firmware?
BNerd89 said:
Slightly off topic but I would stay away from BOC3. Many people I know have had problems with BOC3 Firmware.
I am going to be re-flashing BOC3 when I get back home... I must admit when I flashed BOC3 I didn't do a fresh wipe before flashing it so might have been my problem.
Have you wiped your phone before flashing the firmware?
Click to expand...
Click to collapse
Yes, I wiped from the recovery before and after the BOC3 upgrade and I must say that I like how BOC3 feels.
Battery life feels about the same for me - 50% when I get home (9-5), considering i have BT on all day as i have a smartwatch paired, exchange account, 3 gmails, skype push and a few others.
Love the new Smart Lock features with Trusted Places an On Body Detection.
One thing I noticed, manual check for updates on Security Policy Updates does not give any results, not sure if that is working correctly.
I tried rooting my galaxy j7 with Odin and the feedback I get Is binary size too large
Kindly help me out
#19
I have fixed when up wrong file pit
My phone is samsung note9 128gb
When i try to up file pit on rom . I had loss my store from 128gb to 32gb
I don't find any solotion on web
And i have go to setting , open development setting. Choose lock OEM. After that my phone restart and recover to 128gb
Please share this solution . I hope it can help many people up wrong file pit and loss data store like me .
File up wrong pit file odin by Lock Oem
Recover Lost data store .
Hello,I had this rom installed(https://forum.xda-developers.com/galaxy-s4/i9505-develop/rom-super-wizcyan-29-nov-15-t3259562) and since I'm kind of noob I tried to downgrade to this one ( https://forum.xda-developers.com/showthread.php?t=2454205). I flashed it in TWRP recovery and when the phone finished and restarted i got into a bootloop( i think that's how it's called) - the samsung logo with the light from behind but that's it. I cannot open the TWRP recovery anymore,I cannot restore the stock firmware with KIES, I tried to restore 5.0.1 lollipop stock firmware through ODIN with and without PIT file and also 4.4.2 stock ( i did not find one for my country - Romania, I found one for Germany). Please help me with this issue..I will install any software and just leave it if it works..I just need my phone .. yep,desperate ..)
I'm sorry if I broken any rule by opening a new thread I'm just desperate to solve this issue..been working at it for almost 4 hours..
L.E. Odin says there is no partition when trying to flash the stock roms so i used this PIT file ( CSB_signed_Fusion3_EUR_0325_V2.pit)
Have you tried Smart Switch?
Pwnycorn said:
Have you tried Smart Switch?
Click to expand...
Click to collapse
I don't really know what that is or how should I do it )
Problem fixed. I flashed from a different pc a complete stock rom(bootloader,pit file,csc and all of the other stuff) and it worked perfectly.