Related
Hello all
So I have been doing some flashing and I wanted to restore to the original stock ROM that I made a backup of (via TWRP) right after I rooted my device using the Casual tool in the dev forum but I had a question just to make sure I don't botch anything before I go for the restore:
I am coming from CleanROM 1.5 the MF3 based ROM -- I'm assuming the ROM didn't touch the bootloader
1) I performed an Odin recovery of the I337UCUAMDB baseband version of the OS (factory) from the Dev Forum
2) My original backup was of the I337UCUAMDL baseband version -- Am I able to perform a TWRP restore without causing any problems here?
3) Do I have do Loki-Doki after I restore?
I would try this myself but I really don't want to risk a hard brick in case this isn't the correct way - thanks for the advice in advance all.
An Alternative to this would be to obtain the Odin PDA file for the I337UCUAMDL baseband firmware which I have been unable to locate
Alright well I just went ahead with the restore and The baseband version stayed the same despite the fact that the backup was originally from the MDL baseband. Is there anywhere I can download the Odin file to flash the MDL firmware?
No one's helped me with my problem, so might as well help you out lol! Here's a link for MDL http://storagecow.eu/Xda/AT&T S4/St...s.com-SGH-I337-ATT-I337UCUAMDL-1367050591.zip Flash with Odin
I just did some digging around and actually found this awesome website and I am downloading the MDL right now
http://www.sammobile.com/firmwares/1/?model=SGH-I337&pcode=0#firmware
I do believe that this is legitimate - if not someone please correct me. Have 2 hours until the download is finished anyways lol
TheEmpyre said:
I just did some digging around and actually found this awesome website and I am downloading the MDL right now
http://www.sammobile.com/firmwares/1/?model=SGH-I337&pcode=0#firmware
I do believe that this is legitimate - if not someone please correct me. Have 2 hours until the download is finished anyways lol
Click to expand...
Click to collapse
if you guys need help i can walk you through it step by step; PM me and ill give you my skype or cell number. PM'ed you both.
Slade8525 said:
if you guys need help i can walk you through it step by step; PM me and ill give you my skype or cell number. PM'ed you both.
Click to expand...
Click to collapse
Thanks for the offer -- but as long as the steps are essentially the same as Adam's Factory Stock thread in Android Development then I should be alright! I'm assuming that is the case
TheEmpyre said:
Thanks for the offer -- but as long as the steps are essentially the same as Adam's Factory Stock thread in Android Development then I should be alright! I'm assuming that is the case
Click to expand...
Click to collapse
they should be (post a link ill check).via ODIN, install UCUAMDB, then UCUAMDL, root and install custom recovery, and freeze the update processes (i forget what they are called, im looking for them now) with titanium backup so that it does not auto update to MF3.
if you happen to know the process names or find them, please PM me im making a thread about it.
Panagiotis
Slade8525 said:
they should be (post a link ill check).via ODIN, install UCUAMDB, then UCUAMDL, root and install custom recovery, and freeze the update processes (i forget what they are called, im looking for them now) with titanium backup so that it does not auto update to MF3.
if you happen to know the process names or find them, please PM me im making a thread about it.
Panagiotis
Click to expand...
Click to collapse
Yes, Currently have the MDB installed and running, going to enter download mode and flash MDL via ODIN and basically my plan was to freeze the AT&T auto-update checker application - I have frozen it before and I'm guessing that is the first application in the chain that initiates the update. I'll keep ya posted the MDL is still downloading lol
TheEmpyre said:
Yes, Currently have the MDB installed and running, going to enter download mode and flash MDL via ODIN and basically my plan was to freeze the AT&T auto-update checker application - I have frozen it before and I'm guessing that is the first application in the chain that initiates the update. I'll keep ya posted the MDL is still downloading lol
Click to expand...
Click to collapse
When you finish downloading and flash firmware by oding go ahad and root ifno here : http://forum.xda-developers.com/showthread.php?t=2314494 then install GooManager from play store https://play.google.com/store/apps/details?id=com.s0up.goomanager&hl=en open and from menu choose install script. good luck
All of the information in this thread is readily available in the stickies located in the "General" section. Looking at those threads might save you a lot of time, some potential problems down the road, and help from making mistakes that have already been mentioned. Good luck.
The firmware from (http://www.sammobile.com/firmwares/1/?model=SGH-I337&pcode=0#firmware) was spot on. Used Odin to restore. Already re-rooted and froze a few of the update apps. Thanks all for the help, added [Solved] and altered the title to help guide searches
Long Story As Short As Possible:
1-I Rooted my Sprint Galaxy S4 (with MF9) using Qbking77's You tube instructions (No Probs) !!
2-I dropped the Services.Odex, and Services.Jar into the systems/folder to replace the ones in there using root explorer to get the native hot spot working (It did NOT work) !!!
3-So I flashed via oden a "New" hot spot for rooted roms: "MDCHotspotMod-Odexed" onto the system, and now I am bricked...
I can boot into TWRP, BUT can't flash a rom to the system as it Fails.
I can flash the root "CF-Auto-Root-jfltespr-jfltespr-sphl720.tar" via oden which puts the stock recovery back onto the phone, BUT that wont't flash roms either.
SO, at a complete loss, I factory reset the device wiping everything, and it just boots to the Samsung Galaxy S4 Logo.
I downloaded the following: L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 to try and flash back to stock in Oden, BUT, when I hit "Start" it doesn't do anything but say "The Parameter is incorrect"
This is the Stock MDC File, NOT the MF9 that my phone was currently on...
ANY SUGGESTIONS !!! Thanks guys.
Solved !!! Used MF9 Stock Tar file in Oden !!!
Glad you got it working!
Just in case you were wondering why it didn't work initially - you were on MF9, and you tried to flash the MDC hotspot mod.
And yes, flashing the stock MF9 in ODIN was the right step to fix this. If you now want to install the hotspot mod, make a nandroid backup, download the MF9 version and flash it in TWRP.
jj14 said:
Glad you got it working!
Just in case you were wondering why it didn't work initially - you were on MF9, and you tried to flash the MDC hotspot mod.
And yes, flashing the stock MF9 in ODIN was the right step to fix this. If you now want to install the hotspot mod, make a nandroid backup, download the MF9 version and flash it in TWRP.
Click to expand...
Click to collapse
Any word on getting the hot spot feature working on the MF9 ?? Either Wifi Tether (specific settings), OR the regular built in Hot Spot?? Thanks... Also, I def know about the different software versions I.E. MDL, MDC, and MF9, the site said that particular file would take me back to stock & I would just have to OTA !!! Guess they were wrong, lol...:laugh: Anywho, thanks again, it's nice being able to get help when needed !!!
Ar3ohdee said:
Any word on getting the hot spot feature working on the MF9 ?? Either Wifi Tether (specific settings), OR the regular built in Hot Spot?? Thanks... Also, I def know about the different software versions I.E. MDL, MDC, and MF9, the site said that particular file would take me back to stock & I would just have to OTA !!! Guess they were wrong, lol...:laugh: Anywho, thanks again, it's nice being able to get help when needed !!!
Click to expand...
Click to collapse
Here you go bro, this should do the trick and get a working hotspot mod for you on that s4
http://forum.xda-developers.com/showthread.php?p=40860639
[MOD][Deodex][Odex][MDC][MDL][MF9]Hotspot Mod
gs4 stock rooted running mf9
MENACE_69 said:
Here you go bro, this should do the trick and get a working hotspot mod for you on that s4
http://forum.xda-developers.com/showthread.php?p=40860639
[MOD][Deodex][Odex][MDC][MDL][MF9]Hotspot Mod
gs4 stock rooted running mf9
Click to expand...
Click to collapse
Yep - this is the one that I use as well.
@Ar3ohdee Just make sure that you get the correct version depending on your ROM - odex/deodex and MDC/MDL/MF9
BTW, if you were on stock MDC, you could update OTA to MDL and then to MF9 - that option would have worked too. But flashing the stock MF9 is quicker.
just bricked my galaxy s4 and its stuck at samsung custom screen.. cant get it out of it.... what do i do.. i'm new to this and i new i was going to do this sooner or later....
wahlmart said:
just bricked my galaxy s4 and its stuck at samsung custom screen.. cant get it out of it.... what do i do.. i'm new to this and i new i was going to do this sooner or later....
Click to expand...
Click to collapse
you may need to give us more info than that. what did you try flashing? were you already running a custom rom? mdc, mdl, mf9? did you try manually booting to recovery? (power + vol up)
open a new thread too, may have better luck
Ar3ohdee said:
Solved !!! Used MF9 Stock Tar file in Oden !!!
Click to expand...
Click to collapse
Where'd you find the MF9 Stock Tar file? I screwed up my phone with the wrong version of the hotspot files....
jm1fd said:
Where'd you find the MF9 Stock Tar file? I screwed up my phone with the wrong version of the hotspot files....
Click to expand...
Click to collapse
You mean like from here?
http://forum.xda-developers.com/showthread.php?t=2357471
Bricked on mk2
So I was on stock rooted mk2 with twrp recovery. Did a nand. Flashed kt kernel. Phone wouldn't get passed Samsung splash screen. Couldn't even boot into recovery. Took it to best buy. Tech, if you can call him that, said was bricked and I needed a replacement. Luckily just bought it so free replacement. Played dumb. Probably could have recovered if I Odin the stock firmware. My question is, what do you think caused the brick? Mk2 bootloader? Twrp? The kernel? I flashed plenty of roms and kernels on my s2 without problems. BTW flashed Hotspot mod with cwm and worked.
Hey everyone.
So I jumped the gun and tried to install a custom recovery on my GS4 with MF3. Big mistake, I know. Lucky for me the phone still booted, just recovery was shot. I tried all night to find a solution and all I could find was people referring people like me to Best Buy to maybe get the phone reflashed.
Well, I just fixed it. My wife has a GS4 with MF3 as well. I downloaded an app called "[ROOT] Recovery Tools - Flasher" from the Play Store. Both phones were rooted. I used the tool to "backup" the stock recovery from her phone, I then copied that file from her phone directly to mine. I used "Flash Other Recovery" and selected the backup file from her phone. SUCCESS. Stock recovery was now back.
If you cannot boot and can only get into the "Downloading" screen, then perhaps the backup image from Recovery Tool (An IMG file) can be pushed using Odin? I have no idea. I'm no dev, but I'm very happy to not have a broken recovery anymore.
I was lazy and just used the first file host that popped into Google, but if this works for you then please mirror for others!
Remove the hyphens and copy/paste (I can't include external links, as this is my first actual post)
h-t-t-p://w-w-w-.filedropper.c-o-m/331
Hopefully this is new and I'm not just repeating something everyone already knew, but I had no luck finding a fix for a corrupt MF3.
Good Luck guys, and I take no responsibility if you damage your phone somehow.
EDIT: Apprently a method already existed, although this method doesn't wipe your data!
You could have just used ODIN to flash MF3. You might lose your personal data, but you will have a clean install with recovery. Maybe the method you used might help others that don't want to lose their set-up (personal data and apps) and just need to get the stock recovery back. Thanks for posting about your experience.
scott14719 said:
You could have just used ODIN to flash MF3. You might lose your personal data, but you will have a clean install with recovery. Maybe the method you used might help others that don't want to lose their set-up (personal data and apps) and just need to get the stock recovery back. Thanks for posting about your experience.
Click to expand...
Click to collapse
I couldn't find an MF3 image file to flash, only previous versions. Do you know where there is an MF3 image? Maybe I just failed at searching. Lol
dirronprease said:
I couldn't find an MF3 image file to flash, only previous versions. Do you know where there is an MF3 image? Maybe I just failed at searching. Lol
Click to expand...
Click to collapse
There are several post around the forum with links to the MF3 Odin files that where leaked by @Shockndrop
http://forum.xda-developers.com/showthread.php?t=2502003
http://forum.xda-developers.com/showthread.php?t=2504311
Here's some direct links to the downloads...
MEGA
Mediafire
NighthawkXL said:
There are several post around the forum with links to the MF3 Odin files that where leaked by @Shockndrop
http://forum.xda-developers.com/showthread.php?t=2502003
http://forum.xda-developers.com/showthread.php?t=2504311
Here's some direct links to the downloads...
MEGA
Mediafire
Click to expand...
Click to collapse
Nice! Somehow I missed all of this. In any case I was successful in solving it myself. Hopefully the information will be of some use to someone, even if it's just in not having to wipe their phone. Thanks for the information! I guess having multiple options is at least handy. If I hadn't already figured out a solution you'd have been a life saver though, really. I mean the phone worked fine, but having a broken recovery is just... disconcerting... Lol
scott14719 said:
You could have just used ODIN to flash MF3. You might lose your personal data, but you will have a clean install with recovery. Maybe the method you used might help others that don't want to lose their set-up (personal data and apps) and just need to get the stock recovery back. Thanks for posting about your experience.
Click to expand...
Click to collapse
There is no Odin available for download that currently supports MF3 Firmware.
ajstudios4400 said:
There is no Odin available for download that currently supports MF3 Firmware.
Click to expand...
Click to collapse
Why don't you read before you post?
http://forum.xda-developers.com/showthread.php?t=2502003
Here are the Odin files for mf3.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
ajstudios4400 said:
There is no Odin available for download that currently supports MF3 Firmware.
Click to expand...
Click to collapse
Post less, read more...
..
..
Hello,
Problem:
I own a Samsung Galaxy S4 I337 model from AT&T with a locked bootloader. While using safestrap I accidentally checked the /system folder while wiping the STOCK ROM. I didn't yet have another working ROM loaded onto the phone (Safestrap allows you to boot from multiple different ROMS). My phone now freezes at the Samsung logo when I try to boot normally, and I can't reflash the stock ROM in download mode as the bootloader is still locked (I can, however, boot into download mode).
My phone is recognized by ADB which (theoretically) means I can push files back to the device. I haven't yet tried although I'm afraid it may not work as only 2/3 drivers successfully install on my computer when I plug the phone in.
My request from the great tech gods at XDA Forums:
1) If anyone can please reply with any ideas/solutions to my problem I would greatly appreciate it. (PLEASE, ANYTHING. I'M DESPERATE!)
2) If anyone could supply me with a download for the Galaxy s4 I337 /system folder I could attempt to use ADB to push it onto the phone and reboot. WARNING: I'm not an expert on Android and know nothing about the /system folder. Using the /system folder from your personal phone could supply me with very personal information about you/your phone. Please only do this if you know what you're doing!
My ideas:
1) Use android ADB to push the missing files back to my phone, although I don't know if I deleted the entire /system folder or just select things inside it. Also I can't find any downloads for a /system folder anywhere on the Internet.
2) Take it back to AT&T and play dumb. Hopefully they can at least temporarily unlock the bootloader to reflash the stock ROM for me.
Any ideas are GREATLY appreciated,
JT
PS: If you need any more information please leave a reply and I will update the post ASAP. :good:
EDIT: I am running 4.3 Jellybean. Also in answer to your response, I can't flash the firmware again as the bootloader is locked. (Unless I'm missing something and you know more than me, I'm no expert.)
EDIT 2: Looks like I may be wrong and you can reflash the stock ROM on my locked bootloader. Also, for future responses, my S4 has the MF3 baseband although I'll try the thread you suggested. (With the files for my device of course)
EDIT 3: Having trouble flashing stock firmware again with ODIN even though I've now been told that it's possible, read below for more details. I think it's due to the PIT file or the fact that I was running 4.3 and I believe I am trying to flash back to 4.2.2. Please help!
SOLVED: Thanks to ted77usa, I flashed the MK2 stock ROM to my phone through ODIN and this time everything went without a hitch. THANKS A TON!
Also if any mods want to move/delete/do whatever with this post feel free to do so, I don't see this post being very useful for educational purposes as my logic on locked bootloaders was wrong and I don't want people getting the wrong idea.
What firmware are you on? I'd Odin flash the tar files for that firmware.
JTrocks said:
Hello,
Problem:
I own a Samsung Galaxy S4 I337 model from AT&T with a locked bootloader. While using safestrap I accidentally checked the /system folder while wiping the STOCK ROM. I didn't yet have another working ROM loaded onto the phone (Safestrap allows you to boot from multiple different ROMS). My phone now freezes at the Samsung logo when I try to boot normally, and I can't reflash the stock ROM in download mode as the bootloader is still locked (I can, however, boot into download mode).
My phone is recognized by ADB which (theoretically) means I can push files back to the device. I haven't yet tried although I'm afraid it may not work as only 2/3 drivers successfully install on my computer when I plug the phone in.
My request from the great tech gods at XDA Forums:
1) If anyone can please reply with any ideas/solutions to my problem I would greatly appreciate it. (PLEASE, ANYTHING. I'M DESPERATE!)
2) If anyone could supply me with a download for the Galaxy s4 I337 /system folder I could attempt to use ADB to push it onto the phone and reboot. WARNING: I'm not an expert on Android and know nothing about the /system folder. Using the /system folder from your personal phone could supply me with very personal information about you/your phone. Please only do this if you know what you're doing!
My ideas:
1) Use android ADB to push the missing files back to my phone, although I don't know if I deleted the entire /system folder or just select things inside it. Also I can't find any downloads for a /system folder anywhere on the Internet.
2) Take it back to AT&T and play dumb. Hopefully they can at least temporarily unlock the bootloader to reflash the stock ROM for me.
Any ideas are GREATLY appreciated,
JT
PS: If you need any more information please leave a reply and I will update the post ASAP. :good:
EDIT: I am running 4.3 Jellybean. Also in answer to your response, I can't flash the firmware again as the bootloader is locked. (Unless I'm missing something and you know more than me, I'm no expert.)
Click to expand...
Click to collapse
You can use ODIN just fine on the locked bootloaders. Follow the directions in the MK2 TARs thread in the general section.
RE: ODIN on locked bootloader
DeadlySin9 said:
You can use ODIN just fine on the locked bootloaders. Follow the directions in the MK2 TARs thread in the general section.
Click to expand...
Click to collapse
My phone has the MF3 baseband although I'll try the thread you suggested. (With the files for my device of course) Thanks!
Firmware Number
jd1639 said:
What firmware are you on? I'd Odin flash the tar files for that firmware.
Click to expand...
Click to collapse
I'm on 4.3 Jellybean although I don't believe I can reflash the firmware because of my locked bootloader.
EDIT: According to the above post, I can reflash it. Can someone please clarify what files I will need to do so?
JTrocks said:
I'm on 4.3 Jellybean although I don't believe I can reflash the firmware because of my locked bootloader.
EDIT: According to the above post, I can reflash it. Can someone please clarify what files I will need to do so?
Click to expand...
Click to collapse
You need the mf3 tar files. Have you found then?
Flashing tar files with ODIN
jd1639 said:
You need the mf3 tar files. Have you found then?
Click to expand...
Click to collapse
I'm downloading them now from here. Can you verify for me that this is up to date/correct? I previously tried to flash the .tar.md5 file for my phone although I got a "write error" and after researching it I found that you can't flash files in download mode with a locked bootloader. Apparently this is wrong though, thanks for the all the help so far!
JTrocks said:
I'm downloading them now from here. Can you verify for me that this is up to date/correct? I previously tried to flash the .tar.md5 file for my phone although I got a "write error" and after researching it I found that you can't flash files in download mode with a locked bootloader. Apparently this is wrong though, thanks for the all the help so far!
Click to expand...
Click to collapse
Yep, those are the ones. Read the thread on how to use them
Flashing with ODIN
jd1639 said:
Yep, those are the ones. Read the thread on how to use them
Click to expand...
Click to collapse
I followed the thread exactly as it said but it failed. Then I included the the PIT file but still failed. I've attached a screenshot of ODIN after I tried with the PIT file.
EDIT: My phone is giving a message that reads: "SECURE CHECK FAIL : PIT" I read that PIT files have to be signed with a device-specific key to work, although it seems that most people aren't having a problem using one found off of the Internet. Any ideas?
EDIT 2: I believe those files are for 4.2.2, I was running 4.3, is this the issue? Also I don't know if my phone was updated OTA or not, I bought it from eBay. :/
JTrocks said:
I followed the thread exactly as it said but it failed. Then I included the the PIT file but still failed. I've attached a screenshot of ODIN after I tried with the PIT file.
EDIT: My phone is giving a message that reads: "SECURE CHECK FAIL : PIT" I read that PIT files have to be signed with a device-specific key to work, although it seems that most people aren't having a problem using one found off of the Internet. Any ideas?
EDIT 2: I believe those files are for 4.2.2, I was running 4.3, is this the issue? Also I don't know if my phone was updated OTA or not, I bought it from eBay. :/
Click to expand...
Click to collapse
@JTrocks ....If u are on 4.3 rom it mean that either u took OTA to MK2 firmware and then someone either u or the seller from ebay flash the modem back to MF3 to complete SIM UNLOCKED( if u ever sim unlocked ) .........either way just follow my thread..........
| ★ MK2 ★ FULL ODIN TAR FILES ★ MK2 ★ | ★ UNBRICKED ★ Jan.31.2014 ★ | u can restore to stock 4.3 MK2 firmware or even update to MK2 if u coming from MF3.....tested my self and others confirmed as well....:good::good: Check post #2 for guide on how to ,......BUT IF U STILL WANT TO FLASH THAT MF3.TAR .....TRY TO UN-CHECK RE-PARTITION FROM ODIN ONLY AUTO REBOOT AND F.RESET TIME ARE CHECK.....U DONT HAVE TO LOAD THAT PIT FILE.....JUST BOOTLOADER,PDA,MODEM AND CSC IS ENOUGH....ALSO TRY DIFFERENT ODIN VERSION FROM MY THREAD POST#2 THERE IS ODIN3 V1.85 ....GOODLUCK.....LET ME KNOW HOW IT GO....:good::good:
ted77USA
ted77usa said:
@JTrocks ....If u are on 4.3 rom it mean that either u took OTA to MK2 firmware and then someone either u or the seller from ebay flash the modem back to MF3 to complete SIM UNLOCKED( if u ever sim unlocked ) .........either way just follow my thread..........
| ★ MK2 ★ FULL ODIN TAR FILES ★ MK2 ★ | ★ UNBRICKED ★ Jan.31.2014 ★ | u can restore to stock 4.3 MK2 firmware or even update to MK2 if u coming from MF3.....tested my self and others confirmed as well....:good::good: Check post #2 for guide on how to ,......BUT IF U STILL WANT TO FLASH THAT MF3.TAR .....TRY TO UN-CHECK RE-PARTITION FROM ODIN ONLY AUTO REBOOT AND F.RESET TIME ARE CHECK.....U DONT HAVE TO LOAD THAT PIT FILE.....JUST BOOTLOADER,PDA,MODEM AND CSC IS ENOUGH....ALSO TRY DIFFERENT ODIN VERSION FROM MY THREAD POST#2 THERE IS ODIN3 V1.85 ....GOODLUCK.....LET ME KNOW HOW IT GO....:good::good:
Click to expand...
Click to collapse
Thanks for the reply, but before I go any further I should clarify some information about my phone. I bought an AT&T Samsung Galaxy S4 from eBay, when I got the phone it was running 4.3. The catch: My phone isn't actually on AT&T service OR SIM unlocked (I think), I'm with a cell provider called NET 10. How NET 10 works is that it pays AT&T to run off of their service, NET 10 is cheaper for the customers because it isn't as fast as AT&T. AT&T and Net 10 have an agreement where you can take any phone from AT&T and hook it up to NET 10 without unlocking it. Although I think that NET 10 may unlock your phone when you hook it up to their service, I'm not sure. What makes my think that is that when I booted my phone up after transferring to NET 10, a picture of an open padlock appeared under the Samsung logo.
Being on NET 10 may have changed some of that, specifically the MF3/MK2 baseband. Not being an expert on basebands and how they correlate to your cell service provider, will following your instructions result in not being able to connect to NET 10's service? It's probably a stupid question, I know, but with my minimal knowledge I figured I should ask before I followed through with anything.
JTrocks said:
Thanks for the reply, but before I go any further I should clarify some information about my phone. I bought an AT&T Samsung Galaxy S4 from eBay, when I got the phone it was running 4.3. The catch: My phone isn't actually on AT&T service OR SIM unlocked (I think), I'm with a cell provider called NET 10. How NET 10 works is that it pays AT&T to run off of their service, NET 10 is cheaper for the customers because it isn't as fast as AT&T. AT&T and Net 10 have an agreement where you can take any phone from AT&T and hook it up to NET 10 without unlocking it. Although I think that NET 10 may unlock your phone when you hook it up to their service, I'm not sure. What makes my think that is that when I booted my phone up after transferring to NET 10, a picture of an open padlock appeared under the Samsung logo.
Being on NET 10 may have changed some of that, specifically the MF3/MK2 baseband. Not being an expert on basebands and how they correlate to your cell service provider, will following your instructions result in not being able to connect to NET 10's service? It's probably a stupid question, I know, but with my minimal knowledge I figured I should ask before I followed through with anything.
Click to expand...
Click to collapse
It shouldn't. Your phone is the same model, and the firmware appears to be the same. At most you might have to put in an APN to get your mobile data back.
Continuing with Instructions
DeadlySin9 said:
It shouldn't. Your phone is the same model, and the firmware appears to be the same. At most you might have to put in an APN to get your mobile data back.
Click to expand...
Click to collapse
Thanks, I'm aware of the APN. I had SEVERAL issues with NET 10 when I first set that up. (THEY MISSPELLED THE F****** IP ADDRESS ON THEIR WEBSITE!) Still frustrated about that one. D:<
I'm now preparing to follow through with ted77usa's instructions. Sorry if I respond slow, I have to wait 5 minutes after each post/edit as I haven't been approved by a mod yet.
EDIT: I may have to continue this tomorrow, the site ted77usa used to host the .tar files is pretty slow. The download is going to take an hour and it's getting late here. I can't believe how much support I'm getting from everyone, thanks a TON! I'm clicking the thanks button on everyone who's helped me, it's the least I can do!
JTrocks said:
Thanks, I'm aware of the APN. I had SEVERAL issues with NET 10 when I first set that up. (THEY MISSPELLED THE F****** IP ADDRESS ON THEIR WEBSITE!) Still frustrated about that one. D:<
I'm now preparing to follow through with ted77usa's instructions. Sorry if I respond slow, I have to wait 5 minutes after each post/edit as I haven't been approved by a mod yet.
EDIT: I may have to continue this tomorrow, the site ted77usa used to host the .tar files is pretty slow. The download is going to take an hour and it's getting late here. I can't believe how much support I'm getting from everyone, thanks a TON! I'm clicking the thanks button on everyone who's helped me, it's the least I can do!
Click to expand...
Click to collapse
While u waiting. ... try to read all the thread so that would give u an idea what others issue incase u run same problem..... As long as u check md5 if they match then u should good to go. ... and seem to me u know usb debugging. ...all the driver already installed....PM me if u need more help ....:thumbup::thumbup:
Swyped From MK2 Dark Venom SS Edition
All Good!
ted77usa said:
While u waiting. ... try to read all the thread so that would give u an idea what others issue incase u run same problem..... As long as u check md5 if they match then u should good to go. ... and seem to me u know usb debugging. ...all the driver already installed....PM me if u need more help ....:thumbup::thumbup:
Swyped From MK2 Dark Venom SS Edition
Click to expand...
Click to collapse
AMAZING! Everything went without a hitch!! My phone now indicates that it is running Android 4.3, Baseband version MK2, and calls/texts are working just fine. I have to enter my APN settings again as DeadlySin9 mentioned, but I expect everything should work fine. Thanks to everyone who helped me out (especially ted77usa with the link to his thread), if there's anything I can do to help any of you out in return just let me know! THANKS A TON!!!
JTrocks said:
AMAZING! Everything went without a hitch!! My phone now indicates that it is running Android 4.3, Baseband version MK2, and calls/texts are working just fine. I have to enter my APN settings again as DeadlySin9 mentioned, but I expect everything should work fine. Thanks to everyone who helped me out (especially ted77usa with the link to his thread), if there's anything I can do to help any of you out in return just let me know! THANKS A TON!!!
Click to expand...
Click to collapse
Glad that u got your phone back..... and u also got great community in here...... the best place to learn and give back .....:thumbup::thumbup:
Swyped From MK2 Dark Venom SS Edition
atnt splash screen
JTrocks said:
AMAZING! Everything went without a hitch!! My phone now indicates that it is running Android 4.3, Baseband version MK2, and calls/texts are working just fine. I have to enter my APN settings again as DeadlySin9 mentioned, but I expect everything should work fine. Thanks to everyone who helped me out (especially ted77usa with the link to his thread), if there's anything I can do to help any of you out in return just let me know! THANKS A TON!!!
Click to expand...
Click to collapse
Hey, i had a similar problem. MK2 safe root method. became rooted and everything was great. downloaded xposed framwork/installer. selected fast boot option by accident been stopping at the atnt splash screen ever since. i am able to boot into download/odin mode as well as recovery. I have tried mutiple wipes and facotry resets but same outcome, hangs at atnt screen. i creeped around the threads and found this. My first question is did Ted77usa files from his link take forever for you also? and second how many attmepts did it take with odin?
semarj said:
Hey, i had a similar problem. MK2 safe root method. became rooted and everything was great. downloaded xposed framwork/installer. selected fast boot option by accident been stopping at the atnt splash screen ever since. i am able to boot into download/odin mode as well as recovery. I have tried mutiple wipes and facotry resets but same outcome, hangs at atnt screen. i creeped around the threads and found this. My first question is did Ted77usa files from his link take forever for you also? and second how many attmepts did it take with odin?
Click to expand...
Click to collapse
@semarj If you follow my thread and guide on post#2 it should get u back on stock MK2 less then 6 minutes. .... As long as u have usb debugging check. ... Good usb cable. ....Good driver installed and make sure ONLY auto reboot and F. Reset Time CHECK from Odin..... GOODLUCK. ....PM ME IF YOU NEED MORE HELP. ....:thumbup::thumbup:
Swyped From MK2 Dark Venom SS Edition
semarj said:
Hey, i had a similar problem. MK2 safe root method. became rooted and everything was great. downloaded xposed framwork/installer. selected fast boot option by accident been stopping at the atnt splash screen ever since. i am able to boot into download/odin mode as well as recovery. I have tried mutiple wipes and facotry resets but same outcome, hangs at atnt screen. i creeped around the threads and found this. My first question is did Ted77usa files from his link take forever for you also? and second how many attmepts did it take with odin?
Click to expand...
Click to collapse
It took about an hour for me to download ted77usa's files but I have relatively fast internet (16 mb/ps). As soon as the files downloaded it worked first try, are you in download mode? If you are and it's still not working you may need the PIT file and to make sure that re-partition is checked along with the 2 others that ted77usa mentioned.
drivers finished
ted77usa said:
@semarj If you follow my thread and guide on post#2 it should get u back on stock MK2 less then 6 minutes. .... As long as u have usb debugging check. ... Good usb cable. ....Good driver installed and make sure ONLY auto reboot and F. Reset Time CHECK from Odin..... GOODLUCK. ....PM ME IF YOU NEED MORE HELP. ....:thumbup::thumbup:
Swyped From MK2 Dark Venom SS Edition
Click to expand...
Click to collapse
I will post back asap. the drivers were taking forever to download so i started a kias emergency firmware recovery. thats taking forever also. its only at 79% but have been running for an hour. should i let finish? and if unsuccessful try odin or just quit and do odin?
I recently bit off more than I could chew with my S4 (I337). I had 4.4.2 KitKat on it and wanted to root it to add teathering. I decided thought there was no root for 4.4.2 so I thought I would try downgrading to 4.3 then root. This seemed best because I didn't like the way the SD card is handled in 4.4.2 and some of my apps (like ftp server) have stopped working.
When I got the phone back up from flashing with Odin it says it has version 4.3. My WiFi will not turn on. If I slide the switch to on it slides right back to off and the phone tells me that an operation was block (can't remember the full verbage. I have installed and attempted to install many things on my phone. I have used recovery mode / Odin3 and Kies (Kies doesn't allow much).
At this point I just would like to get my phone back to 4.4.2 with the WiFi working. Then I can restore my backup and be back to square one with a lesson learned.
I have an I337 that currently thinks it has version 4.3 on it. The baseband version is I337UCUFNC1 currently. The build number is JSS15J.I337UCUEMK2.
If anyone can help I would greatly appreciate it. I have read and tried many things over a two day period and finally decided to ask for help.
Had this issue before on my Bell Canada S4, but don't recall exact way to fix it.
Think the solution was to find an older (might be newer) stock. I think I used a different version like the Telus Canada version as well and it ended up working. Then you update through kies after.
jbrudda said:
I recently bit off more than I could chew with my S4 (I337). I had 4.4.2 KitKat on it and wanted to root it to add teathering. I decided thought there was no root for 4.4.2 so I thought I would try downgrading to 4.3 then root. This seemed best because I didn't like the way the SD card is handled in 4.4.2 and some of my apps (like ftp server) have stopped working.
When I got the phone back up from flashing with Odin it says it has version 4.3. My WiFi will not turn on. If I slide the switch to on it slides right back to off and the phone tells me that an operation was block (can't remember the full verbage. I have installed and attempted to install many things on my phone. I have used recovery mode / Odin3 and Kies (Kies doesn't allow much).
At this point I just would like to get my phone back to 4.4.2 with the WiFi working. Then I can restore my backup and be back to square one with a lesson learned.
I have an I337 that currently thinks it has version 4.3 on it. The baseband version is I337UCUFNC1 currently. The build number is JSS15J.I337UCUEMK2.
If anyone can help I would greatly appreciate it. I have read and tried many things over a two day period and finally decided to ask for help.
Click to expand...
Click to collapse
Root, install safestrap then flash this ROM and you will be good to go: http://forum.xda-developers.com/showpost.php?p=52167774&postcount=3
Thanks
muniz_ri said:
Root, install safestrap then flash this ROM and you will be good to go: http://forum.xda-developers.com/showpost.php?p=52167774&postcount=3
Click to expand...
Click to collapse
Quite a few steps in those threads but I got it working again. I really appreciate all the help/advice given. Now to decide if I want to remove the safestrap screen on boot. Again Thanks.
Same problem,need help plz
Hi guys,
I have the same problem as jbrudda.i wiped everything using Odin3_v3.09 and AP_I337UCUEMK2_1921628_REV06_user_low_ship_MULTI_CERT.tar . and now my wifi is not working. when i try to turn it on a security message pop up (the device has detected an application attempting to perform actions that are not permitted these actions have been blocked)and ask me to reboot, then it does a factory reset on its own. but the problem is still there no wifi. my baseband is diffrent than jbrudda's. mine is I337UCUAMDB. can someone plz help. thank you
karim8888 said:
Hi guys,
I have the same problem as jbrudda.i wiped everything using Odin3_v3.09 and AP_I337UCUEMK2_1921628_REV06_user_low_ship_MULTI_CERT.tar . and now my wifi is not working. when i try to turn it on a security message pop up (the device has detected an application attempting to perform actions that are not permitted these actions have been blocked)and ask me to reboot, then it does a factory reset on its own. but the problem is still there no wifi. my baseband is diffrent than jbrudda's. mine is I337UCUAMDB. can someone plz help. thank you
Click to expand...
Click to collapse
Wifi does not work because of the modem/kernel mismatch, i.e. MDB modem and MK2 kernel. Not sure what your goal was when you began flashing your phone but since you fortunately did not flash teh MK2 bootloader you are still able to locate the MDB full odin tar and flash back to stock which will resolve your issue.
muniz_ri said:
Wifi does not work because of the modem/kernel mismatch, i.e. MDB modem and MK2 kernel. Not sure what your goal was when you began flashing your phone but since you fortunately did not flash teh MK2 bootloader you are still able to locate the MDB full odin tar and flash back to stock which will resolve your issue.
Click to expand...
Click to collapse
I did Root it with saferoot and safestarp.the wifi didnt work so i had to find a script here on xda and i run it throughout universal init.d . i didnt like the way my phone was running . so i decided to unroot it . so you think im using the wrong TAR file ???
karim8888 said:
I did Root it with saferoot and safestarp.the wifi didnt work so i had to find a script here on xda and i run it throughout universal init.d . i didnt like the way my phone was running . so i decided to unroot it . so you think im using the wrong TAR file ???
Click to expand...
Click to collapse
It depends on what you are trying to accomplish. Are you trying to upgrade to MK2 or higher while maintaining your unlocked MDB bootloader?
muniz_ri said:
It depends on what you are trying to accomplish. Are you trying to upgrade to MK2 or higher while maintaining your unlocked MDB bootloader?
Click to expand...
Click to collapse
I'm just trying to take it back to the why it was. and upgrade to kitkat. i have now build number JSS15J.I337UCUEMK2 baseband : I337UCUAMDB
what do you think i should do?? I appreciate your help.
karim8888 said:
I'm just trying to take it back to the why it was. and upgrade to kitkat. i have now build number JSS15J.I337UCUEMK2 baseband : I337UCUAMDB
what do you think i should do?? I appreciate your help.
Click to expand...
Click to collapse
If you don't care about losing your MDB unlocked bootloader you can get to the latest kitkat firmware by flashing the NB1 full odin tar from here:
http://forum.xda-developers.com/showthread.php?t=2674223, then once flashing is complete go to settings/more/about phone/software update then take the ota update to NC1 which is the latest kitkat version for our phone.
But what I would do is keep your unlocked MDB bootloader and since you already flashed the MK2 AP file you can get your phone running well again by flashing the MK2 modem: https://mega.co.nz/#!pwESna5I!YK7EKG37xXIG1ReB-Z-mfSMoXNkXQ9t2EdMK9ofgJKg
From there, there are still a number of options available to get to kitkat which I won't get into.
muniz_ri said:
If you don't care about losing your MDB unlocked bootloader you can get to the latest kitkat firmware by flashing the NB1 full odin tar from here:
http://forum.xda-developers.com/showthread.php?t=2674223, then once flashing is complete go to settings/more/about phone/software update then take the ota update to NC1 which is the latest kitkat version for our phone.
But what I would do is keep your unlocked MDB bootloader and since you already flashed the MK2 AP file you can get your phone running well again by flashing the MK2 modem: https://mega.co.nz/#!pwESna5I!YK7EKG37xXIG1ReB-Z-mfSMoXNkXQ9t2EdMK9ofgJKg
From there, there are still a number of options available to get to kitkat which I won't get into.
Click to expand...
Click to collapse
I will try this steps and let you know.thanks a lot.
It worked "muniz_ri". Thanks a lot for your help, I really appreciate it. :laugh::good:
karim8888 said:
It worked "muniz_ri". Thanks a lot for your help, I really appreciate it. :laugh::good:
Click to expand...
Click to collapse
Hey guys.
I lost al sounds on my phone now.Wifi is running , I thought the fix worked but the sound is out now. any suggestions???
Thank you.
jbrudda said:
I recently bit off more than I could chew with my S4 (I337). I had 4.4.2 KitKat on it and wanted to root it to add teathering. I decided thought there was no root for 4.4.2 so I thought I would try downgrading to 4.3 then root. This seemed best because I didn't like the way the SD card is handled in 4.4.2 and some of my apps (like ftp server) have stopped working.
When I got the phone back up from flashing with Odin it says it has version 4.3. My WiFi will not turn on. If I slide the switch to on it slides right back to off and the phone tells me that an operation was block (can't remember the full verbage. I have installed and attempted to install many things on my phone. I have used recovery mode / Odin3 and Kies (Kies doesn't allow much).
At this point I just would like to get my phone back to 4.4.2 with the WiFi working. Then I can restore my backup and be back to square one with a lesson learned.
I have an I337 that currently thinks it has version 4.3 on it. The baseband version is I337UCUFNC1 currently. The build number is JSS15J.I337UCUEMK2.
If anyone can help I would greatly appreciate it. I have read and tried many things over a two day period and finally decided to ask for help.
Click to expand...
Click to collapse
I told you not to drink and root.
jbrudda said:
Quite a few steps in those threads but I got it working again. I really appreciate all the help/advice given. Now to decide if I want to remove the safestrap screen on boot. Again Thanks.
Click to expand...
Click to collapse
excited to give this a try. rooted with the downgrade method a couple months ago but left with a non-wifi device. my only issue is that the thread says it's for I337UCUFNC1 and our devices are on jss15j.i337ucuemk2. will this fix still work? I've heard on other threads on the subject that the modem kernel doesn't match up with the flashed rom or build number or something.
bux
karim8888 said:
Hi guys,
I have the same problem as jbrudda.i wiped everything using Odin3_v3.09 and AP_I337UCUEMK2_1921628_REV06_user_low_ship_MULTI_CERT.tar . and now my wifi is not working. when i try to turn it on a security message pop up (the device has detected an application attempting to perform actions that are not permitted these actions have been blocked)and ask me to reboot, then it does a factory reset on its own. but the problem is still there no wifi. my baseband is diffrent than jbrudda's. mine is I337UCUAMDB. can someone plz help. thank you
Click to expand...
Click to collapse
Do you already fix it??? cause i have the same problem
Same question, different thread!
Not even an hour ago did I answer the same question in a different thread: How do I get WiFi working on my S4?
Well here you go.
My original answer: http://forum.xda-developers.com/gal...-4-4-2-nb1-t2850878/post54978150#post54978150
The problem is, in order to get WiFi working, you need to install the NB1 modules, but to do that, you need to install Safestrap. However, you can not install Safestrap because the app keeps closing on you. There is a simple fix to this, which I will explain later. For now, just read this WHOLE post BEFORE you do anything, and keep in mind that I am NOT held liable if you mess up your phone. Use this at your own risk.
1.) Root your phone
If you're already rooted with something like SuperSU or Superuser, skip this. If not, read ahead. Download and install the Towelroot APK file attached to this post, open it, and click 'make it ra1n'. If your phone didn't reboot, now you have root (they need to trademark that). Now, down below, I also included the APK for SuperSU. Download and install it. Now open it. When you open it, let it install the 'Normal' way, not via the 'TWRP/CWM' way. Also, when it asks you to disable KNOX, say yes, wait a couple of minutes (it will still be loading) and reboot your phone. Open up SuperSU again, click 'Yes' to disable KNOX again, and now you have a good base to start from.
2.) Install Safestrap AFTER fixing the error
The error your are getting is easily fixed. Go to the Play Store and install 'SELinux Mode Changer'. Open it, grant it root access, and change the mode to 'Permissive'. Now, open up Safestrap again (you mentioned you already installed it), and it shouldn't force close. Click 'Install', and if the 'Reboot to Recovery' option below is not grayed out after that then it worked.
3.) Download and install the NB1 modules
On your phone, download the included NB1 modules ZIP file I attached for you, and once that is done you need to reboot. After the Galaxy S4 logo, you'll see a screen that says 'SAFESTRAP: DISABLED' and there will be a little robot. TIP: To enter Safestrap, press the menu button (physical, hardware key) under 'Recovery' at that screen. To continue to Android, press the back key (again, physical) under the 'System' tab. For now, press the menu button under 'Recovery'. Now, click 'Install' which should be in red, click 'Add zips', and navigate to your Downloads folder. Now click on the NB1 modules ZIP you just downloaded. Swipe to install, and reboot. This time, hit the back key under 'System'.
All done!
Now, Android should (and will) boot up, and you'll have working WiFi! If, for some odd reason, you don't have WiFi- do NOT panic! Just search around for the MF3 modules and flash those! All is good, all is good. A lot of this guide was taken from my post about my personal method of SIM unlocking the AT&T Galaxy S4 without the dialer codes or an AT&T SIM. It was just modified a little to work for you.
Remember, hit thanks!
Click to expand...
Click to collapse
Those are my exact words. Also, the attached files (NB1 modules, SuperSU, Towelroot, etc.) can be found attached to my post in the link above. Have a good night, and best of luck! :good::good::good:
Had the Wifi Not Working - Fixed
muniz_ri said:
If you don't care about losing your MDB unlocked bootloader you can get to the latest kitkat firmware by flashing the NB1 full odin tar from here:
http://forum.xda-developers.com/showthread.php?t=2674223, then once flashing is complete go to settings/more/about phone/software update then take the ota update to NC1 which is the latest kitkat version for our phone.
But what I would do is keep your unlocked MDB bootloader and since you already flashed the MK2 AP file you can get your phone running well again by flashing the MK2 modem: https://mega.co.nz/#!pwESna5I!YK7EKG37xXIG1ReB-Z-mfSMoXNkXQ9t2EdMK9ofgJKg
From there, there are still a number of options available to get to kitkat which I won't get into.
Click to expand...
Click to collapse
I just flashed I337MK2StockModem.tar.md5 and now it works!! I'm on the MK2 and rooted with saferoot and safestrap recovery 3.72
iqcomputers said:
I just flashed I337MK2StockModem.tar.md5 and now it works!! I'm on the MK2 and rooted with saferoot and safestrap recovery 3.72
Click to expand...
Click to collapse
See the thread I started with a similar problem.
http://forum.xda-developers.com/galaxy-s4-att/help/rogers-samsung-s4-4-2-2-i337m-wifi-t3256535
Would I be able to use this fix?