[Q] N4 only turns on when charging - Nexus 4 Q&A, Help & Troubleshooting

Couldn't find any response or anyone with the same problem here. If it's the right place. Please, let me now.
I only can use it when it's plugged at the wall charger. And sometimes I can enter fastboot and recovery using the laptop. When I take out the cable, it dies again.
Tryed all stock versions (4.2, 4.3, 4.4 and 4.4.2) and all the same.
Tryed three new batteries and then go from 0 to 100% in one minute the go back to 0 and starts charging again.
I noticed that every time I try a new battery, it show the red led, and to start charging, I must hold power 10-15 sec then i can see the battery icon with the flashlight then charging. But when I press power after 15 hours of charging, the red light appears again. So i keep pressing and it turns on, but with the same result.
Any idea?
PD. Sorry about my english.

contapapo said:
Tryed three new batteries ...
Click to expand...
Click to collapse
I am curious, how are you able to so easily swap out the batteries?
Has it always behaved like this (from new), randomly one day or after you changed something for example ROM, Kernel, some hardware etc?

Mr_JMM said:
I am curious, how are you able to so easily swap out the batteries?
Has it always behaved like this (from new), randomly one day or after you changed something for example ROM, Kernel, some hardware etc?
Click to expand...
Click to collapse
After the first one, you are able to open and close it in 2 min.
One day it turned off and never woke up again. :crying:

Nobody? I'm about to put it in the garbage.

I've got a similar issue to the OP, I can force my phone to start, and have left it to "charge", but as soon as i disconnect the charger, the battery percentage goes down about 20%. if i then turn the phone off, I get a solid red notification light for about a second. to get the phone to turn on, i hold down the power and volume down buttons. If i hold down the power and volume up buttons, it appears to start charging, but never actually does. Any suggestions on how to get it to charge?

Related

Charging problem ..

(Bare with me, this IS wm6 related)
Okay, so i got this qtek 9090 from a trade online, and the owner pointed out that he had used it for some time now and it worked without problems.
However that seems not to be my experience. At first I was a little worried that it did not came with a charger.. Only a USB cable. No worries i thought, I will just charge it through USB. Now I have had some experiences where phones wouldn't charge from some of my computers, apparently because of some boards that put out lower amps than others. However I knew atleast one computer should have no problem charge ordinary cell phones.
So i plugged it in, and to my worries the battery kept going down... Untill the phone was dried from power and everything got lost again.. and again.. and again.. It seemed a little odd that it apparently deleted everything each time, since the backup battery indicated 100%.
So at last it went into flightmode and I shut it down with the powerbutton and let it be connected.. The first many hours nothing happened.. But suddenly, when i did an occasional check, it said 3% battery. I went to sleep and the next morning it was fully charged. I used it all day in school and it held its power real fine.
Now I got the feeling that this probably was caused by the low amp output from the computer, making it unable of charging to the extend where the phone would still be able of running whilst charging. So i figured i would order a 220v (the powercurrent here in Denmark) -> 5v USB that outputs 700mA, to make a quicker charge.
Well, to day I was gonna receive that adapter, and since I'd read that the wm6 apparently draines the battery some bit, I waited untill today to upgrade to wm6.
I upgraded and everything truely runs quick and stable. But when i recieved the adapter and plugged it in, i was horrified. The power kept going down, as I had experienced when it was plugged into USB.
Now my girlfriend really wanted to play bejeweled on this thing, so she did and then shortly afterwards we took a few hours nap. I had her plug it in the new adapter to charge it. When i woke up i saw the screen blinking.
I could se it was rebooting over and over again, as it had done the first time it completely lost power..
Now besides that extremely annoying charging problem, I now had another concern....
The boot screen shows NONE next to the R and the G.
Next to the D is the wm version displayed.
Any help would be greatly appreciated.
red LED?
Hm.. By doing a hard reset it shows numbers next to R and G again.
It continuely reboots, display boot screen, shuts down, LED is red, reboots, displays boot screen, shuts down, LED is red again and again.
If i hard reset it some times it will at one point stay off, but the LED still lights red.
And now I question wether 700mA is even enough for charging the BA?
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
jakubd said:
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
Click to expand...
Click to collapse
AFAIK the lower the mA output, the slower the charge period.
I have had wifi, bluetooth, beam off. I've set shutdown to 2 minutes. I've set it to low brightness and etc.
As i mentioned it had no problems going a whole day of usage in school.
Didn't know about the bug in wm6 that makes only the screen shut off, but at the momemt i can't even boot the device, apparently because it has no batterypower. And having it connected to the charger makes no real difference (other than it will display the bootscreen and perhaps even the Windows Mobile welcome screen thing, for a few seconds.. then go dead again.)
I've had it in the charger for about an hour or two, still not enough power to boot it up.
It feels like it's just not charging sometimes.. And other times it will charge just fine.
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
jakubd said:
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
Click to expand...
Click to collapse
Hmm, i see. I just don't understand why it's not charging then :/
trylleklovn said:
Didn't know about the bug in wm6 that makes only the screen shut off
Click to expand...
Click to collapse
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
trylleklovn said:
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Click to expand...
Click to collapse
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
jakubd said:
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
Click to expand...
Click to collapse
Okay.
It's odd still. When i connect the charger the right LED starts to light red.
If it means that its not charging, there must be something wrong, since it only happens when connecting the charger..
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
jakubd said:
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
Click to expand...
Click to collapse
I KNOW that, but it is not going amber. It stays red all the time.
Found this thread that discusses a similar problem; http://forum.xda-developers.com/archive/index.php/t-233782.html
Apparently it shows RED light all the time if the battery is dead.. However i hardly doubt that the battery, which could power the phone just fine for and entire day, should be dead.
However, one suggestion in the thread was to take out the battery for some time and then try again. So I will do that for now.
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
trylleklovn said:
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
Click to expand...
Click to collapse
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
motisu said:
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
Click to expand...
Click to collapse
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
trylleklovn said:
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
Click to expand...
Click to collapse
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
motisu said:
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
Click to expand...
Click to collapse
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
trylleklovn said:
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
Click to expand...
Click to collapse
I have found that if you only use the USB cable to charge, it takes much longer (if at all) to charge if it is on. Thats why I bought cradles that have external power suppies as well as the USB sync cable. With this configuration, it gets to full charge in about 90 minutes.
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
trylleklovn said:
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
Click to expand...
Click to collapse
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
motisu said:
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
Click to expand...
Click to collapse
Yeah, i tried that. As soon as i press the power button it goes to red again.
Update..
A litte update (i might as well document everything I find out here, if anyone should run into a similar problem).
Now, I've had the device connected to the charge for some time now.
What happens is that the device boots up, automaticly dimms down to no light (since i once had hold down the power button, to dimm down light).
Then it boots up, and i can see everything running.
I can navigate to the battery status menu, which shows
Battery: 0% (charging)
Backup battery: 25%
After a few minutes the device shuts down, and the LED goes red again. But after about a half a minute it will try to boot up again, and it goes through everything again.
What I've noticed is that the backup battery slowly increases, and while im writing it has gone all the way to 75%. The good thing about this completely automatic procedure is that it apparently slowly charges, at least, the backup battery.
My theory is that the backup battery has first priority in the system, so that the regular battery wont charge untill the backup battery is up. And since the backup battery can't apparently be used for actualy powering the system, the system will continuesly reboot because of lack of power, theoreticly untill the backup battery reaches 100% and it starts to charge the regular battery.
The whole problem seems to be cause by some charging malfunction, so that both batteries has been completely discharged. I hope that by letting it continue to reboot, charge, reboot, charge, etc. it will revive the battery.
I will return with more info tomorrow.
Any suggestions are still greatly appreciated.

[Q] Help, Blank Screen, Backlight on, no picture

Pretty self explanatory. It was dead for a couple of days, I put it on the charger for almost the whole day, now I get no picture, but the backlight is on when I hold the power down a minute. I bought it at walmart, doubt I have the receipt, and didn't get any extended warranty. Is there a way to fix this issue?
I've got the same issue. I was playing Tupsu, when suddenly my n7 rebooted and there was no picture, just semi-strong backlight. When the tablet died, the battery was about 45-50% and I was charging it through notebook's usb port (original n7 cable). I tried to turn it off, but pressing and holding the power button only made it reboot once again (i assume it was rebooting, since the backlight was turning off and on in a second). I've tried it many times, with tablet plugged into wall/usb charger, and even with the power+volume up/down combination, it would still behave the same way. However sometimes after rebooting there was not only backlight, but also thin, mostly white, horizontal lines, appearing in random places of the screen (appearing and disappearing after like 50-100 ms). It would stop only after a reboot, and happened every 5-10 reboots.
I've decided to let the battery die to see if it changes something, and as you may guess - it didn't. It died estimately after 2 or 3 hours. Now it's all the same, except for when I plug it to the charger, there's only a very low backlight (still no picture) and it's blinking... It also makes this continuous "electricity-related" (sorry, I don't know what's the word to call it ) sound. After I press the power on, or let it charge for 1-2 minutes it boots up, and there's just a semi-strong backlight, like earlier.
It's a refurbished 8gb n7, which I got 5 days ago from the polish Asus online store. Oh, and the speakers weren't 100% fine, if it changes something. They were fine at first, but after i plugged headphones in and out, they were making cracking sounds when the volume was over 50% or something like that. Is there any hope I can fix it myself?
edit: the android ver. is 4.2.2, not rooted
the device is getting warm on the left side when being charged, or just turned on...
Have you tried pulling the battery for a couple of minutes?
Sent from my Nexus 7 using Tapatalk HD
Nope, i don't want to mess with the hardware since i've bought it only few days ago... I'm afraid it may leave some traces of being opened, i'm not willing to take the risk.
You won't leave a trace pulling the battery. Just use a guitar pick or credit card and run it round, the back comes off very easily.
Sent from my GT-I9000 using Tapatalk 2
Yeah that is definitely worth a shot. Just pull the battery.
Ok, I did it.
Didn't change a thing >:[
btw. I didn't actually pulled off the battery, i've just disconnected it - it doesn't make a difference, does it? and another thing - the backlight was turning on immediately after connecting the battery... with these randomly popping horizontal lines.
I've got this too!
wujekandrzej said:
Ok, I did it.
Didn't change a thing >:[
btw. I didn't actually pulled off the battery, i've just disconnected it - it doesn't make a difference, does it? and another thing - the backlight was turning on immediately after connecting the battery... with these randomly popping horizontal lines.
Click to expand...
Click to collapse
I've got this too! Pulling the battery does nothing. Last time it just fixed itself, now nothing.
Worried I'll have to take mine back.
How did that 'fixing itself' happened to you if i may ask? And how long did it last?
Your tablet has gone into sleep mode to protect the battery from further damage due to its low level of charge. What you're seeing is by design, as complete discharge of a lithium based battery is bad for it. You should never, ever, let it sit dead for a couple days. If you do discharge it to the point of shutdown again, immediately put some sort of charge on it, as waiting to long will cause the battery's protection circuit to fail completely. Best practice is to not let your device go to the point of shutdown, but rather to plug it in when not in use. Your battery will have a longer lifespan.
Plug your N7 into the charger and immediately press power and volume down to get into the bootloader. Once there, use the volume key to scroll to Power Off Device and then press the power button. After it powers off, unplug it and then plug it back in. It should then charge normally.
You seem not to have read my posts at all. When it happened, the battery was about 45-50% and it was plugged into the laptop's usb port. It suddenly rebooted and there was no more picture, just the backlight - and it lasted for like 2-3 hours (maybe even longer)! Can a completely discharged battery power the backlight for this long? After it turned off at last, i put it on charge and i've tried the power+volume method and it didn't do anything (btw. i already wrote about it)... then i let it charge for like 5-6 hours and it didn't change anything except for the fact, that the battery was evidently charged, because the backlight again lasted for few hours.
wujekandrzej said:
You seem not to have read my posts at all. When it happened, the battery was about 45-50% and it was plugged into the laptop's usb port. It suddenly rebooted and there was no more picture, just the backlight - and it lasted for like 2-3 hours (maybe even longer)! Can a completely discharged battery power the backlight for this long? After it turned off at last, i put it on charge and i've tried the power+volume method and it didn't do anything (btw. i already wrote about it)... then i let it charge for like 5-6 hours and it didn't change anything except for the fact, that the battery was evidently charged, because the backlight again lasted for few hours.
Click to expand...
Click to collapse
Actually, I was addressing the OP without realizing that this was a zombie thread.
To answer your question though... yes, when in sleep mode the battery can still turn on the backlight and keep it powered for some time due to the low power requirement of a black screen. Many users that have found themselves in sleep mode actually have their tablets enter into a prolonged cycle of bootloops. From the sounds of it, your device seems to have, for reasons unknown, put itself to sleep.
Anyway, I digress... I know you've stated you've tried various combinations of the power and volume keys. Have you attempted holding all three buttons for approximately 30-40 seconds while the tablet is plugged in? If it that will force it into the bootloader, you can follow the steps that I posted to get it up and running again. If not, then it seems your best available option is to seek an RMA from ASUS. Given your speaker issue, I'd send it back regardless- you shouldn't be expected to deal with battery and speaker issues after only five days.
najaboy said:
Actually, I was addressing the OP without realizing that this was a zombie thread.
Click to expand...
Click to collapse
Ok, then i'm sorry for few harsh words
najaboy said:
Anyway, I digress... I know you've stated you've tried various combinations of the power and volume keys. Have you attempted holding all three buttons for approximately 30-40 seconds while the tablet is plugged in?
Click to expand...
Click to collapse
Yep. Many times. And even longer than a minute.
Anyway, I'm going to contact their crappy support. Thanks everyone for trying to help.

Flashing red light wont turn on!

Recently my n4 has been giving me a flashing red light whenever i turn it on. No matter what combination of buttons i press, it doesn't do anything. Please help! Using a 1 amp charger.
neostyles said:
Recently my n4 has been giving me a flashing red light whenever i turn it on. No matter what combination of buttons i press, it doesn't do anything. Please help! Using a 1 amp charger.
Click to expand...
Click to collapse
There have been many cases like these. I think you will get enough hits if you use the search button. I had it myself recently, though the solution seems not to be very solid.
The best way to get it to work is to try different cables/chargers (via PC/Wall Chargers etc) and let it charge for a half hour, and try to start it. If it doesn't start, try another combination. Rinse, repeat.
A stronger charger seems to work better most of the time (2A for example).
In the end I got it to work with the 2A charger of a colleague that he always carries with him. I am assuming that there is nothing wrong with your battery besides it being completely drained.
Im not really sure though. Is that what the flashing red light means?
Open the phone up, pop off the battery connection, put it back, then try to reboot (you can reboot with the cover off). I got the red light after my N4 crashed doing an Antutu test after OC'ing it to 1.9GHz (yeah...don't do that), and after "resetting" the battery, it booted up just fine.
I had ever occur this issue and tried any fix from internet, finally completely battery died, so just buy a new one of battery .
Your battery is discharged to a critical level (1-2%) and the phone performed a shutdown to save itself.
Connect your phone to the charger and press POWER + VOLUME DOWN, to enter recovery. Then reboot from recovery
I had the RED LIGHT flashing and this is how i fixed my problem. No need to buy a new battery
Ur phone can't boot up cuz there is not enough energy from ur battery, so just charge ur phone for a while then u can boot up ur phone again red light issue usually for low battery and the phone can't booting up
i doubt it if mine is power issue. I've charged for long periods several times, i've tried several things i could find on the internet, i used a working battery, still no show. light blinks for a while and goes off when plugged to electricity. I'm thinking this could be a different problem entirely

[Q] N4 doesnt turn on. Red Light blinks once.

Hello.
When I try to turn on my N4, I hold power button, and after about 10 seconds Red light blinks (just once, if it's connected to USB that 1 blink last for 3 seconds, if connected to wall, it's just quick 1 blink. If it not connected anywhere there is no action at all, it just stays dead, no blinks, nothing). Same if I try to go in bootloader by holding volume down+power.
This happened after I successfully installed CM12, with no errors. Then I rebooted my phone, and it just stayed black as it is now. Battery was around 25~30% that time, and phone was connected to USB.
Did I bricked my phone totally? I am now trying to charge it up already for 1 hour... but it nothing changes.
I have searched here for similar problems, but couldn't find solution...
Edit: Charging already for 10h+ , still same..
Edit2: I removed battery, reconnected after a while, still same problem.
So I tested it with multimeter, it says 2.6V, but fully charged must be 3.8V. Could this be a problem? I was charging it for whole night.
Edit3: I just got new battery . But it looks the same.. phone doesn't boot up.. same red light blinks once.. so.. its my phone is dead? I can't believe that...
When I connect to PC usb, there are unrecognized deviced called "QHSUSB_DLOAD".
easy fix
Hold down the power button and the volume down button at the same time until phone reboots. If you see the little android no need to worry just let go and wait for your device to reboot on its own. This is not a factory reset it's just like restarting your device. :good:
zelexon said:
Hold down the power button and the volume down button at the same time until phone reboots. If you see the little android no need to worry just let go and wait for your device to reboot on its own. This is not a factory reset it's just like restarting your device. :good:
Click to expand...
Click to collapse
I have tried that many times. Nothing. It's bootloader screen, but I can't get there. Nothing happens. If I keep holding volume down+power it just keep blinking once every ~10 seconds, same if I hold just power button. If phone is not connected to charger, there are no blinks at all.
I removed battery, reconnected after a while, still same problem.
So I tested it with multimeter, it says 2.6V, but fully charged must be 3.8V. Could this be a problem? I was charging it for whole night.
Cracken6 said:
I removed battery, reconnected after a while, still same problem.
So I tested it with multimeter, it says 2.6V, but fully charged must be 3.8V. Could this be a problem? I was charging it for whole night.
Click to expand...
Click to collapse
I had the same problem a year ago, I tried to remove the battery, charging all night, and other solutions that I found online and no one worked.
Finally I found here in XDA a user with the same problem and his solution was charger the phone with a wireless charger, a friend of mine has one and I put the phone to charge and after a few minutes the screen goes on and the phone was charged, then I press power button and the nexus run again.
Hope this works.
Sorry for my bad English, I'm from Spain.
Good luck.
(I bought a wireless charger in case it happen again)
I don't know anyone with wireless charger. I already ordered a new battery, and then I probably will get wireless charger also. Ty.
But this problem is very weird if you think so.. I think it happened because of many aspects together:
1) Battery was already below 30%
2) I pretty regularly charge phone with USB (won't do it again)
3) It was connected to PC USB in same time.
4) I installed CM12 ROM in same time
So main reason I think is USB, that I restarted phone while it was on pretty low battery and with USB connected.. phone restarted and got invalid voltages and couldn't even boot up or charge phone. I also found an article which says, minimum voltage, when phone battery has 0%, it's 3.0V, so I was below that.. it just screwed everything and battery died. Well, I am not sure for 100% that it's battery fault, but I hope so, I really love my N4 and still wanna use it for long time, I hope it's not dead phone, just a dead battery. Lets see! I will update this thread , when I get my new battery (less than month probably).
Sorry, my english is also not perfect. I am from Latvia.
I was playing when it happened to me. The phone was very very hot and the battery was around 70%. When I put in the wireless charged and I can reboot the phone the battery was at 65%, so it had charge but the phone won't boot.
I charge my phone almost every day, sometimes with AC, others with USB (plugging to PC) or wireless that depends of my needs
I hope you can fix it. Good luck.
Btw. Do you know if battery charges with wireless charger, if it's removed from the phone?
Don't think it does, since the receiving coils for wireless charging are located just behind the glass back.
Flipz77 said:
Don't think it does, since the receiving coils for wireless charging are located just behind the glass back.
Click to expand...
Click to collapse
The battery will charge with a NCF Charger
Major Issue Google
This "Nexus SOD" issue is showing up on many sites across the Internet. I have multiple "Nexus" devices including 2 Nexus 4, 1 Nexus 5, 2 "Nexus 7 2013". It suddenly started out of the blue with one of my Nexus 4 phones. Symptoms included rapid battery discharge. I am using Lollipop 5.1 on all devices. There are many claims as to the cause, Hardware Motherboard, Power Button etc. Others claim it is "Software Related" or App Related. The problem effects Nexus 4 and Nexus 5 phones. I have ordered a new motherboard for my nexus 4 device and see if that makes a difference.
This problem should warrant a "Major Android Lollipop Crisis Team" by Google to investigate the cause and let us know what it is and what Google is doing to solve the problem before moving to announce "Android M". This issue needs to brought up and actively pursued at the upcoming "Google I/O Conference" by the strong Android Developers Groups to press for "Formal Action"
charging method
Cracken6 said:
I have tried that many times. Nothing. It's bootloader screen, but I can't get there. Nothing happens. If I keep holding volume down+power it just keep blinking once every ~10 seconds, same if I hold just power button. If phone is not connected to charger, there are no blinks at all.
Click to expand...
Click to collapse
I had this problem a long time ago and my fix worked for me after doing a little research it seems like this is a case called battery total discharge. The fix was simply to charge your phone using the wall adapter that came with your phone (I still use my old apple cube wall thing) and to wait for the red light to appear then wait about ten minutes before trying to reboot.
I just got new battery . But it looks the same.. phone doesn't boot up.. same red light blinks once.. so.. its my phone is dead? I can't believe that...
When I connect to PC usb, there are unrecognized deviced called "QHSUSB_DLOAD".
Maybe this video will help you: Oh I´m not allowed to post links until now.
Just search for: - Nexus 4 "red light of death" fix - at youtube.
Hope it will help
AndRe5575 said:
Maybe this video will help you: Oh I´m not allowed to post links until now.
Just search for: - Nexus 4 "red light of death" fix - at youtube.
Hope it will help
Click to expand...
Click to collapse
I have checked all kind of videos there. Also that one. Most of these cases are related to battery, but it seems in my case it isn't. I just searched for QHSUSB_DLOAD unrecognized device, all posts says it means phone is bricked... But cmon, how? I installed CM12, successfully, without any errors, then just restarted phone, and its dead...
Cracken6 said:
I have checked all kind of videos there. Also that one. Most of these cases are related to battery, but it seems in my case it isn't. I just searched for QHSUSB_DLOAD unrecognized device, all posts says it means phone is bricked... But cmon, how? I installed CM12, successfully, without any errors, then just restarted phone, and its dead...
Click to expand...
Click to collapse
Did u try booting the phone without battery by connecting to wall charger and what about flashing stock ROM via PC
Also check that the power button works
This case should be solved
as9333 said:
Did u try booting the phone without battery by connecting to wall charger and what about flashing stock ROM via PC
Also check that the power button works
This case should be solved
Click to expand...
Click to collapse
Just tried booting without battery, and connecting to wall. Same - red light blinks once, after I hold Power button or Power+Volume down for about 15 seconds. If I keep buttons pressed, it just repeats every ~15 seconds.
Power buttons works fine.
After I checked that Device manager thing in google.. it looks very bad.. phone is dead.. probably need to change motherboard. I am just shocked, how this could happen... I didn't receive any errors during CM12 installation. Phone just instantly died after restart.

How to turn on wileyfox storm after battery fully drained.

Hello to all experts.
1- Accidently my wileyfox storm battery was fully drained at night and i was not at home during that time.
I connected mobile to wall outlet it was showing red colour on home button when connected (as a battery charging indication) but after near about 8 hours i tried to turn it on but no luck. I pressed power button for many seconds, many times but no luck.
Now what should I do to turn on my wileyfox storm.
2- My second question is how to open back cover of my wileyfox storm. i did not find any notch or point to open back cover to see inside.
Thanks in advance.
Plug your phone on charge but not in usb, and wait about 20mn
I am having this problem as well right now, how did you fix it?
I too have the same problem , it was off because drain , but then put in office is no longer lights . the light is always red . what can I do?
Leave it charging for a while from the mains. Red light means charging on low charge, the screen doesn't turn on until it has some charge.
it is normal to be in power for eight hours, and nothing has changed ? Red light always on and off screen
rugabella said:
it is normal to be in power for eight hours, and nothing has changed ? Red light always on and off screen
Click to expand...
Click to collapse
Have you tried holding down the power button now?
Johndawolf said:
Have you tried holding down the power button now?
Click to expand...
Click to collapse
yes , and unfortunately nothing happens . problems that can have ? He does not get the charge? because it comes on the same spy and it is always red ? the phone has just three months
for anyone who is interested I solved !!! simultaneously press power button and volume less for about 20 seconds and the phone switches
rugabella said:
for anyone who is interested I solved !!! simultaneously press power button and volume less for about 20 seconds and the phone switches
Click to expand...
Click to collapse
Im dealing with the same problem from morning. Im going to try your solution by 10 minutes.
ijaz1976 said:
Hello to all experts.
1- Accidently my wileyfox storm battery was fully drained at night and i was not at home during that time.
I connected mobile to wall outlet it was showing red colour on home button when connected (as a battery charging indication) but after near about 8 hours i tried to turn it on but no luck. I pressed power button for many seconds, many times but no luck.
Now what should I do to turn on my wileyfox storm.
2- My second question is how to open back cover of my wileyfox storm. i did not find any notch or point to open back cover to see inside.
Thanks in advance.
Click to expand...
Click to collapse
I am no expert, but I've had the same problem after fully running the phone battery down. While looking for an answer I managed resolve the issue by to hold the power down and down array while the phone in chagrining for around 2 minutes and the phone started up, almost by complete accident.
rugabella said:
for anyone who is interested I solved !!! simultaneously press power button and volume less for about 20 seconds and the phone switches
Click to expand...
Click to collapse
Hi rugabella
please guide me
I have same problem
since 17:30 today my storm battery drained and when i put it in charge LED light RED
it not Happened before , until now (20:44) phone is in charge and LED light is red
I tried time to time the key combination you mentioned (Power + volume Down) but nothing happens
now I'm waiting for more time to spent charging
Can you or someone else help me more?
tiosus said:
Hi rugabella
please guide me
I have same problem
since 17:30 today my storm battery drained and when i put it in charge LED light RED
it not Happened before , until now (20:44) phone is in charge and LED light is red
I tried time to time the key combination you mentioned (Power + volume Down) but nothing happens
now I'm waiting for more time to spent charging
Can you or someone else help me more?
Click to expand...
Click to collapse
16hours and still RED light and nothing else
any help!!!!!!!!!!!!!?
tiosus said:
16hours and still RED light and nothing else
any help!!!!!!!!!!!!!?
Click to expand...
Click to collapse
I had the same issue you are having, battery ran down to empty, charge light would always be red no matter how long it was plugged in, slow charge, fast charge, holding down the power button, even with the inclusion of the vol down, nothing worked.
I fixed it by opening up the phone and disconnecting then reconnecting the the battery. After doing so the phone started to properly charge (phone booted up and displayed the battery animation). Everything now operates as normal, though I won't be letting it drain to 0% again, that's for sure.
If you're able to, give it a shot and hopefully it will do the trick for you as well (though I'm probably way to late).
Hello to all
I again have the same problem, the battery of my storm has fully discharged, but although is it charging for many hours the LED light is always red and the phone will not turn on. This time even while holding together power button and volume less nothing is happening.
Can anyone help me and tell me how I can fix ?
Level1imp how did you open the phone to disconnect the battery ?
level1imp said:
I had the same issue you are having, battery ran down to empty, charge light would always be red no matter how long it was plugged in, slow charge, fast charge, holding down the power button, even with the inclusion of the vol down, nothing worked.
I fixed it by opening up the phone and disconnecting then reconnecting the the battery. After doing so the phone started to properly charge (phone booted up and displayed the battery animation). Everything now operates as normal, though I won't be letting it drain to 0% again, that's for sure.
If you're able to, give it a shot and hopefully it will do the trick for you as well (though I'm probably way to late).
Click to expand...
Click to collapse
How i did you open up the phone? I'm struggeling with it
Thank you soooo much!!!!
rugabella said:
for anyone who is interested I solved !!! simultaneously press power button and volume less for about 20 seconds and the phone switches
Click to expand...
Click to collapse
After I read your message here, I've tried and finally I solved this problem in my phone.
I was getting crazy because there isn't place to fix this phone in my country and the company Wileyfox wanted me to send my phone to someone in europe to them send to Wilefox to fix it. I've spoke with the company today to see what could they do for me and the solution they gave to me was this and to I try to open the back by myself. But this last solution it isn't a solution because would make me loose the garantee. Why the technician didn't told me about this solution? I'm so disappointed with them.
hi i have a wileyfox storm it is not going on when i press power button .now i connect with wall charger so it show a red circle on the bottom and phone show logo on and of .how can i put it on
This works!!
For anyone who needs it, this also works on wileyfox swift 2
Had this too, but solved
Just had this problem occur on my Wileyfox Swift 2 Plus. Completely drained, left on charge for 4h but it got 0% charged in that time.
For me, hooking it up to a slightly stronger power source (5V 2.1A) USB port of my power bank,
in combination with Power + Volume UP
Got me to a boot screen I'd never seen before.
Hit Fast Boot, it looked like it just turned off again but a few seconds later I saw the normal boot screen pop up

Categories

Resources