Hello to all the community ..
I'm desperate with my cell phone, I have a galaxy s4 (sgh-I337m) and stopped working today ..
I had the cell phone connected to the charger, when the battery finished charging disconnect the cable and cell phone was shut down automatically.
Try to turn on the phone again, but I get into a bootloop, samsuns logo appears and restarts again .. :crying:
I searched a lot about the problem, all posts recommend entering the recovery and make the respective wipes, but in my case I can not do that, the phone does not go into recovery mode.
The download mode works perfectly.
With odin flashie the last official firmware for my cell phone, the installation is correct and odin did not mark any error, but the phone still with the same problem again and can not enter the recovery mode, but can enter download mode .. .
Also try installing a custom recovery, but again can not go into recovery mode.
Any solution for this?
PD: Sorry for my English ..
Well I'm not sure if you've tried these yet but I'll give it a shot. If you're on 4.2 / 4.2.2 I would look at this thread. If you're on 4.3 I'd look at this thread. It should resolve your bootloop / brick issues from occuring in the future if it ever happens again. Hope this helped you out somewhat.
Rytiou said:
Well I'm not sure if you've tried these yet but I'll give it a shot. If you're on 4.2 / 4.2.2 I would look at this thread. If you're on 4.3 I'd look at this thread. It should resolve your bootloop / brick issues from occuring in the future if it ever happens again. Hope this helped you out somewhat.
Click to expand...
Click to collapse
He's using a Canadian S4, not AT&T.
lince_0011 said:
Hello to all the community ..
I'm desperate with my cell phone, I have a galaxy s4 (sgh-I337m) and stopped working today ..
I had the cell phone connected to the charger, when the battery finished charging disconnect the cable and cell phone was shut down automatically.
Try to turn on the phone again, but I get into a bootloop, samsuns logo appears and restarts again .. :crying:
I searched a lot about the problem, all posts recommend entering the recovery and make the respective wipes, but in my case I can not do that, the phone does not go into recovery mode.
The download mode works perfectly.
With odin flashie the last official firmware for my cell phone, the installation is correct and odin did not mark any error, but the phone still with the same problem again and can not enter the recovery mode, but can enter download mode .. .
Also try installing a custom recovery, but again can not go into recovery mode.
Any solution for this?
PD: Sorry for my English ..
Click to expand...
Click to collapse
It does seem like you've tried everything. However, try this: unplug your phone and try to enter recovery mode by pressing the power button and volume up button simultaneously until you see "Booting recovery..." in blue at the top left when the screen turns on. Once you see that, release the buttons IMMEDIATELY. Sometimes the phone reboots in normal mode if you try to boot into recovery mode with the phone plugged in.
Thanks for responding.
My cell phone can not enter the recovery.
Booting recovery appears blue, but the phone rebooted again.
What else can I try to fix the error?
Please i need help..
I don't know what else can do
lince_0011 said:
Thanks for responding.
My cell phone can not enter the recovery.
Booting recovery appears blue, but the phone rebooted again.
What else can I try to fix the error?
Click to expand...
Click to collapse
ill help. one sec
edit
I also have gs4 I337m. important to note that flashing a custom recovery will trip knox, and void the warranty. when you bootbinto download mode, look for knox lines. good is 0x0, warranty void is 0x1.
download jellybean 4.3 from Samsung-updates.com. be sure to use the region code for your carrier.
perform a factory wipe before starting via stock recovery. use odin and make sure to copy any .ini files included in the stock firmware to your odin folder before flashing. this is important step, if.ini file exists. overwrite if you have another ini file from a previous package already in odin.
use pda button to browse to extracted package. img file and be sure to tick *only* auto reboot and f reset flags.
flash. once successful, boot back into stock recovery and perform another factory reset. this is important to clear any left over munged up sys and usr data.
if all of this still fails, use kies3 and the emergency recovery option. wizard based and will also flash back to factory if odin isnt writing. make sure you have the latest samsung drivers before starting, and make sure you use another usb cable other than the one you've been bad flashing with. use another computer if possible, or at least another usb port to rule out bad cable/usb port.
barring all of that, you can use an unbrick package. i have the files to load via adt if needed. i just ran the script to produce the unbrick files, script isnt mine, from another xda dev.
of you arent comfortable using adt, then find your local best buy, they will repair for free most cases, small nominal fee for tripped knox flags or other carriers.
message me for the unbrick files if you need them. via pm. i wont dump them here.
Sent from my SGH-I337M
azuziel said:
ill help. one sec
Sent from my SGH-I337M
Click to expand...
Click to collapse
ok am waiting
ping, see edit
Sent from my SGH-I337M
---------- Post added at 11:07 PM ---------- Previous post was at 11:04 PM ----------
oh, and remove kies when flashing with odin. i would uninstall entirely, and also remove the usb drivers, and install latest from Samsung/attaching phone after uninstall from device manager. if u have questions, just ask. kies will interfere with odin, its happened to me.
Sent from my SGH-I337M
pregunta
lince_0011 said:
ok am waiting
Click to expand...
Click to collapse
Que tal Lince soy de chihuahua tambien y tengo el mismo problema, vi en htcmania que lograste solucionarlo que te paso ahora?
Related
Hello guys i was trying out the new Kangabean 4.3. ROM for my AT&T and after flashing it in TWRP it appears I has softbricked my device. I can only boot into download (odin) mode and it stays on "downloading now".. Anyhow i cannot boot into recovery it just vibrates to confirm my input and just revibrates and revibrates... Looked all over for guides and tried to return it to factory settings on Kies but it does not detect my phone... Any help would be great i need this phone for work everyday!!!
Karbooo said:
Hello guys i was trying out the new Kangabean 4.3. ROM for my AT&T and after flashing it in TWRP it appears I has softbricked my device. I can only boot into download (odin) mode and it stays on "downloading now".. Anyhow i cannot boot into recovery it just vibrates to confirm my input and just revibrates and revibrates... Looked all over for guides and tried to return it to factory settings on Kies but it does not detect my phone... Any help would be great i need this phone for work everyday!!!
Click to expand...
Click to collapse
Please search for similar threads. This same issue is being posted over and over and over again. When you were making this post, what "similar threads" or "similar topics" showed up? Did you check them for a solution?
yes sorry i looked at all of them and they all involved well just flashing the stock rom but i cant get my computer to see my gs4 on download mode...i got the drivers and odin installed.
Well, this thread has a couple of ideas...
http://forum.xda-developers.com/showthread.php?t=2405991
or maybe here...
http://forum.xda-developers.com/showthread.php?t=2405127
You might also want to look at the TWRP thread in the development section.
Try again to get into recovery, the key sequence can be tricky, make sure you are doing it just right. "Doing it just right" has been discussed many times.
Also, look at this thread, maybe it will help...
http://forum.xda-developers.com/showthread.php?t=2398336
Yea, I realize that thread is about MF3, but it still has ideas that might help you.
There are also a ton of threads about how to get your PC to recognize ODIN.....search.......good luck.
yeah ive been at it for hours man those links can all access the recovery i cant... i tried everything got the drivers up tried all the odins and its just stuck on "downloading do not turn off target" and my pc doesnt see it...
Odin finally recognized it on the pc in download mode and i was able to flash the stock rom but it seems it wasnts successful...it still just vibrates and vibrates when i press the power...
Try flashing the open recovery.
Sent from a jedi extacy note II
If you mean the CWM recovery I tried it on Odin and it failed.... :""(
Sent from my Nexus 7 using xda premium
Take battery out, back in, power+volumedown, download mode, Install Samsung Kies, do Kies update, connect to PC, Tools-> firmware initialization, take battery out and type model/serial Number, wait patiently until it finishes.
Try different USB port or different PC. Use stock USB cable comes with original box.
If Kies screen get stuck at model number section, you did flash MF3 triangle thingy -> unsolveable brick. Have to go thorugh warranty replacement.
Sent from my SGH-I337 using Tapatalk 4
the Kies Emergency firmware utility worked it put my phone like the day i bought it...also rooted it successfully and installed TWRP on it thanks guys
Hi everyone, I'm new here. I have a problem regarding my galaxy grand prime sm-g530h. I have rooted that device. In the process of deleting system apps may be Ive deleted som other systems. When I reboot my phone it stucks on its name . Ive reset my factory data nd cache too. Now im anable to connect wiht samsung kies for emergency recovery. Because its not possible to connect samsung kies without enabling usb debug. I have searched many threads regarding my phones problem but didnt found anything. Is there anyone to help me out this situation? Suggestions will be appreciated.
rajukhadka19782 said:
Hi everyone, I'm new here. I have a problem regarding my galaxy grand prime sm-g530h. I have rooted that device. In the process of deleting system apps may be Ive deleted som other systems. When I reboot my phone it stucks on its name . Ive reset my factory data nd cache too. Now im anable to connect wiht samsung kies for emergency recovery. Because its not possible to connect samsung kies without enabling usb debug. I have searched many threads regarding my phones problem but didnt found anything. Is there anyone to help me out this situation? Suggestions will be appreciated.
Click to expand...
Click to collapse
You must use ODIN
go to download mode then flash your rom
rajukhadka19782 said:
Hi everyone, I'm new here. I have a problem regarding my galaxy grand prime sm-g530h. I have rooted that device. In the process of deleting system apps may be Ive deleted som other systems. When I reboot my phone it stucks on its name . Ive reset my factory data nd cache too. Now im anable to connect wiht samsung kies for emergency recovery. Because its not possible to connect samsung kies without enabling usb debug. I have searched many threads regarding my phones problem but didnt found anything. Is there anyone to help me out this situation? Suggestions will be appreciated.
Click to expand...
Click to collapse
i have same problem after i install app from google play try to flash rom can,t find 1 that work
plz help.
you need to use odin to flash the stock firmware back going into download mode and for rom just visit - http://www.sammobile.com/ and download firmware from there just see you model and select you country and download latest stock rom and flash it or else tell me your model number and country i will provide you link
AmGaD-SaLaH said:
You must use ODIN
go to download mode then flash your rom
Click to expand...
Click to collapse
Thanks dude for the suggestion.
me 2
Me 2, I want to unbrick it how to download my firmware?
Galaxy Grand Prime SM-G530/H/DV is Not accepting ODIN connection
Galaxy Grand Prime SM-G530/H/DV
Hi
I have Samsung Galaxy Grand Prime SM-G530/H/DV model . I did factory Reset . Then TouchWiz stopped problem arose. I disabled TouchWiz and installed APUS Launcher. That worked fine. Then I want to give cell to another person. I did Factory Reset again. After this the following problems arose.
1- A pop up massage during booting arose. “Unfortunately Process com. Android. systemUI has been stopped”
2- Above mentioned message hang the cell on Main Screen, I can not operate any function.
3- IMEI No. INVALID.
4- Mobile cannot be accepted connection with PC, ODIN, Kies etc.
Kindly guide me in this regard as I am a beginner in the matter of programming etc.
maq66 said:
Galaxy Grand Prime SM-G530/H/DV
Hi
I have Samsung Galaxy Grand Prime SM-G530/H/DV model . I did factory Reset . Then TouchWiz stopped problem arose. I disabled TouchWiz and installed APUS Launcher. That worked fine. Then I want to give cell to another person. I did Factory Reset again. After this the following problems arose.
1- A pop up massage during booting arose. “Unfortunately Process com. Android. systemUI has been stopped”
2- Above mentioned message hang the cell on Main Screen, I can not operate any function.
3- IMEI No. INVALID.
4- Mobile cannot be accepted connection with PC, ODIN, Kies etc.
Kindly guide me in this regard as I am a beginner in the matter of programming etc.
Click to expand...
Click to collapse
Seems like the EFS partition is broken (IMEI Invalid)
If You don't have any backups done by custom recovery, well... You're probably done.
I am having a similar problem. After enabling KNOX, which I thought was just another antivirus, my phone rebooted, and just got stuck. It would go to the boot page, with the name, and then it would act like it was gonna go to my home screen, but the screen would go black and it would start over. I cleared the cache and factory wiped it, but still no luck. I didn't enable usb debugging, and from what I know there is no way to enable it. I need it to use odin to flash a rom and start over. any suggestions?
dineshjumani said:
you need to use odin to flash the stock firmware back going into download mode and for rom just visit - http://www.sammobile.com/ and download firmware from there just see you model and select you country and download latest stock rom and flash it or else tell me your model number and country i will provide you link
Click to expand...
Click to collapse
Hay, @rajukhadka19782: Man, can you please tell me, whether you found a way to flash firmware with in a dead Samsung Galaxy Grand Prime, I mean my device is dead at all, it has no Download mode, no recovery. Just a light black screen and nothing more not even boot loops that could help me.
I need your help please try having some way out there
talvigi said:
Hay, @rajukhadka19782: Man, can you please tell me, whether you found a way to flash firmware with in a dead Samsung Galaxy Grand Prime, I mean my device is dead at all, it has no Download mode, no recovery. Just a light black screen and nothing more not even boot loops that could help me.
I need your help please try having some way out there
Click to expand...
Click to collapse
I'm with the same problem! All solutions need to go to download or recovery mode, but I can't turn on my phone and Odin can't catch it! Please, could somebody help me?
Thanks!
lucas13garcia said:
I'm with the same problem! All solutions need to go to download or recovery mode, but I can't turn on my phone and Odin can't catch it! Please, could somebody help me?
Thanks!
Click to expand...
Click to collapse
Does your device start at all or not? if it starts tell me what do you see? Is the battery charged, anden have you tried Odin 1.87, and have you tired to flash repair firmware 4.4.4, please Try it and make sure to only flash BL file first.
Sent from my SAMSUNG-SM-G920A using Tapatalk
talvigi said:
Does your device start at all or not? if it starts tell me what do you see? Is the battery charged, anden have you tried Odin 1.87, and have you tired to flash repair firmware 4.4.4, please Try it and make sure to only flash BL file first.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Hey, thank you for the help!
It starts and it doesn't! With the battery, after I try to turn on, it keeps blinking repeatedly and stops only if I remove the battery. And my issue with any fix that I try to flash is that the computer doesn't recognize, probably cuz the blinking blue light is just a random light and not the phone actually trying to turn on... so Odin, for example, doesn't catch any device!
Is there any way to make the computer recognize it? I already tried some usb drivers, but nothing so far... BTW, I have a windows 10.
Thanks!
lucas13garcia said:
Hey, thank you for the help!
It starts and it doesn't! With the battery, after I try to turn on, it keeps blinking repeatedly and stops only if I remove the battery. And my issue with any fix that I try to flash is that the computer doesn't recognize, probably cuz the blinking blue light is just a random light and not the phone actually trying to turn on... so Odin, for example, doesn't catch any device!
Is there any way to make the computer recognize it? I already tried some usb drivers, but nothing so far... BTW, I have a windows 10.
Thanks!
Click to expand...
Click to collapse
Well Windows 10 64bit has been creating problems for many many people in the forum and I have seen people running vm and win 7 for the best results. And something very important I must say is that, most of the new computers do have USB 2.0 ports but they are limited in number, so you should find one on ur PC, to us it specifically for phone tweaking softwares. I would suggest you find another PC or laptop around,
Sent from my SAMSUNG-SM-G920A using Tapatalk
talvigi said:
Hay, @rajukhadka19782: Man, can you please tell me, whether you found a way to flash firmware with in a dead Samsung Galaxy Grand Prime, I mean my device is dead at all, it has no Download mode, no recovery. Just a light black screen and nothing more not even boot loops that could help me.
I need your help please try having some way out there
Click to expand...
Click to collapse
Without recovery or Download mode, you'll need to take it to someone with a black box or jtag.
If you can access a working phone of your same model, you can boot download mode from sd
http://forum.xda-developers.com/grand-prime/development/fix-g530-debrick-img-guide-to-make-t3422115
Guys, I just tried to root my samsung galaxy grand prime but now it is not booting up. it just shows the logo and the screen becomes black after that. also dowload mode is not working. same thing happens when i try to go into download mode
mrunank said:
Guys, I just tried to root my samsung galaxy grand prime but now it is not booting up. it just shows the logo and the screen becomes black after that. also dowload mode is not working. same thing happens when i try to go into download mode
Click to expand...
Click to collapse
What happens when you go to download mode?
---------- Post added at 06:10 PM ---------- Previous post was at 06:09 PM ----------
mrunank said:
Guys, I just tried to root my samsung galaxy grand prime but now it is not booting up. it just shows the logo and the screen becomes black after that. also dowload mode is not working. same thing happens when i try to go into download mode
Click to expand...
Click to collapse
Did you try wiping cache and what is your model?
waleeds1 said:
What happens when you go to download mode?
---------- Post added at 06:10 PM ---------- Previous post was at 06:09 PM ----------
Did you try wiping cache and what is your model?
Click to expand...
Click to collapse
My model is SM530H I cannot enter the recovery mode to wipe the cache . When I try to go into the recovery mode, samsung logo flashes and then the screen goes blank. Same thing happens when i try to normally switch on the phone
mrunank said:
My model is SM530H I cannot enter the recovery mode to wipe the cache . When I try to go into the recovery mode, samsung logo flashes and then the screen goes blank. Same thing happens when i try to normally switch on the phone
Click to expand...
Click to collapse
What about download mode? Btw it should not go to logo it should go to recovery after bootimage. You should hold down power home and volume down untill download mode comes or power home and volume up untill recovery menu comes
Hi guys,
I own a Galaxy Note 4 (N910H) and have rooted it before without any problem.
Long story short I wanted to install a custom rom and on the instruction says I need to reset my device to factory before I actually install it (because mine is 4.4.4).
I successfully reset it back to factory settings, however when I tried to install the rom an error occured.
When my device restarted it goes into a boot loop.
So I go into the recovery mode and delete the caches and what not (even selecting the reset to factory setting again).
When my device restart it is stuck at the boot sreen (samsung galaxy blablabla) and it DOESNT LOOP, it just stuck there and I am unable to go into recovery mode.
I tried to reflash it using odin (i can access the downloading mode) up to no avail.
My device is detected by odin (com:x) but when I pressed start it stuck at setup connection and after a while I got the Fail message.
Now I am at a loss and have no idea what else to do. Tried kies, doesnt work either.
Kies doesnt even recognize the connection to my phone.
Any help would be appreciated.
NB: I'm a newb at this so please bear with me (and yes I kind of ****ed up)
Thanks
xverdex said:
Hi guys,
I own a Galaxy Note 4 (N910H) and have rooted it before without any problem.
Long story short I wanted to install a custom rom and on the instruction says I need to reset my device to factory before I actually install it (because mine is 4.4.4).
I successfully reset it back to factory settings, however when I tried to install the rom an error occured.
When my device restarted it goes into a boot loop.
So I go into the recovery mode and delete the caches and what not (even selecting the reset to factory setting again).
When my device restart it is stuck at the boot sreen (samsung galaxy blablabla) and it DOESNT LOOP, it just stuck there and I am unable to go into recovery mode.
I tried to reflash it using odin (i can access the downloading mode) up to no avail.
My device is detected by odin (com:x) but when I pressed start it stuck at setup connection and after a while I got the Fail message.
Now I am at a loss and have no idea what else to do. Tried kies, doesnt work either.
Kies doesnt even recognize the connection to my phone.
Any help would be appreciated.
NB: I'm a newb at this so please bear with me (and yes I kind of ****ed up)
Thanks
Click to expand...
Click to collapse
If I'm not mistaken you have Kies installed? If that is the case I would recommend you uninstall it. Then manually download the Samsung USB drivers
http://developer.samsung.com/technical-doc/view.do?v=T000000117
Reboot your PC just to be sure.
Then make sure your device isn't connected to the charger or computer and remove the battery and after 10 seconds reinsert the battery and manually boot into Download Mode (Home + Volume Down while holding the power button.)
Then connect your phone to the your PC and run Odin as Admin and try to flash the firmware.
I would also recommend that the firmware you are flashing is the correct one and is not corrupted.
You can check the firmware from Sammobile and after the download check the MD5Sum and then extract the zip file to get the firmware file.
Good luck and report back.
Sent from my trltexx using XDA Premium 4 mobile app
I had the same problem , make sure to properly install samsung drivers
if everything is still messed up , try a fresh copy of windows and install samsung drivers and the latest " Flash Tool "
i hope this fix up ur problem
Battlehero said:
Reboot your PC just to be sure.
Then make sure your device isn't connected to the charger or computer and remove the battery and after 10 seconds reinsert the battery and manually boot into Download Mode (Home + Volume Down while holding the power button.)
Then connect your phone to the your PC and run Odin as Admin and try to flash the firmware.
I would also recommend that the firmware you are flashing is the correct one and is not corrupted.
You can check the firmware from Sammobile and after the download check the MD5Sum and then extract the zip file to get the firmware file.
Good luck and report back.
Sent from my trltexx using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Just to make sure, should I put the MD5 file to bootloader or AP/PDA?
Thank you for the help, I will try your solution after I get back from work
xverdex said:
Just to make sure, should I put the MD5 file to bootloader or AP/PDA?
Thank you for the help, I will try your solution after I get back from work
Click to expand...
Click to collapse
If you are using Odin version 3.09 or above it's AP, otherwise it's PDA.
Sent from my SM-N910F using XDA Premium 4 mobile app
Battlehero said:
If you are using Odin version 3.09 or above it's AP, otherwise it's PDA.
Sent from my SM-N910F using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Thanks Battlehero! now I finally get my galaxy note back to work again.
Now let's say if I want to Root my device again, is it as simple as installing CWM or TWRP and then install a custom rom?
xverdex said:
Thanks Battlehero! now I finally get my galaxy note back to work again.
Now let's say if I want to Root my device again, is it as simple as installing CWM or TWRP and then install a custom rom?
Click to expand...
Click to collapse
If you want to root your current rom then install a custom recovery (TWRP) recommended then flash SuperSU Current release: https://download.chainfire.eu/740/SuperSU/BETA-SuperSU-v2.49.zip
You can always hit the 'Thanks Button' to show your appreciation. It's nice to see you fixed your issue.
Battlehero said:
If you want to root your current rom then install a custom recovery (TWRP) recommended then flash SuperSU Current release:
You can always hit the 'Thanks Button' to show your appreciation. It's nice to see you fixed your issue.
Click to expand...
Click to collapse
Done with the 'Thanks Button'.
Thanks for the help!
Cheers mate
Hello,
I was trying to flash Twrp recovery in my phone using flashify. It said flash successfully and i rebooted. It starting bootlooping. I manually tried by pressing Volume up + Home+Power keys it was still doing bootloop. I tried to goto download mode by pressing Volume Down+ Home+Power keys it still kept bootlooping even USB jig didn't work. I need your valued suggestion about what to do next.
Thanks in Advance.
I have Samsung Galaxy Grand Primr G530H
here is video link youtu.be/B_EtRTH93YE
Just flash your firmware from Odin using a PC, I had a similar problem in my tablet, it didn't had download mode either and that worked, try it.
When I connect it to Pc it keeps bootlooping and pc gives sound of connecting then disconnecting of hardware.
GorJessSpazzer said:
Just flash your firmware from Odin using a PC, I had a similar problem in my tablet, it didn't had download mode either and that worked, try it.
Click to expand...
Click to collapse
How did you flash a firmware, when your tablet didn't have download mode? What ODIN version did you use? please tell us we need your experience.
talvigi said:
How did you flash a firmware, when your tablet didn't have download mode? What ODIN version did you use? please tell us we need your experience.
Click to expand...
Click to collapse
Turn off your device, keep your finger in the button until the device is off or pull off the battery, connect it to the PC and flash your firmware through Odin, at that moment I used the 3.70 i think but you can use the latest version it's fine, that should install download mode and the whole firmware if that doesn't work I'm afraid I don't know how else I can help, that's what I did and it worked
GorJessSpazzer said:
Turn off your device, keep your finger in the button until the device is off or pull off the battery, connect it to the PC and flash your firmware through Odin, at that moment I used the 3.70 i think but you can use the latest version it's fine, that should install download mode and the whole firmware if that doesn't work I'm afraid I don't know how else I can help, that's what I did and it worked
Click to expand...
Click to collapse
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead bur or wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me food the step by step procedure it was just like this:
1. I started the Odin 3.07 and connected my device to see is it was detected or not, my surprise the Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down button pressed to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. From that moment I knew my device was not dead now so i had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
talvigi said:
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead bur or wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me food the step by step procedure it was just like this:
1. I started the Odin 3.07 and connected my device to see is it was detected or not, my surprise the Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down button pressed to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. From that moment I knew my device was not dead now so i had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
I'm glad I helped you and thanks for your description, other people with the same problem can see it, my English its not good and I was afraid that I didn't help you correctly.
Same problem, but apparently worst!
AwkWeirdo said:
Hello,
I was trying to flash Twrp recovery in my phone using flashify. It said flash successfully and i rebooted. It starting bootlooping. I manually tried by pressing Volume up + Home+Power keys it was still doing bootloop. I tried to goto download mode by pressing Volume Down+ Home+Power keys it still kept bootlooping even USB jig didn't work. I need your valued suggestion about what to do next.
Thanks in Advance.
I have Samsung Galaxy Grand Primr G530H
here is video link youtu.be/B_EtRTH93YE
Click to expand...
Click to collapse
Hello guys! Could you please help me with the same issue? The difference is that Odin doesn't recognize when I plug in my phone! I don't know what else to do. It's a G530H.
Thank you very much!
GorJessSpazzer said:
I'm glad I helped you and thanks for your description, other people with the same problem can see it, my English its not good and I was afraid that I didn't help you correctly.
Click to expand...
Click to collapse
talvigi said:
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead but it wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me for the step by step procedure it was someting like this:
1. I started the Odin 3.07 and connected my device to see if it was detected or not, to my surprise, Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down + home key pressed, to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. or the device. From that moment I knew my device was not dead now so i pullup the battery, put it again inside to check its status, did this almost thrice, but still the same black screen, yet i heard the startup sound everytime. Now as far as knew the phone is on but showing nothing, I had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin bar which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Sent from my SAMSUNG-SM-G920A using Tapatalk
lucas13garcia said:
Hello guys! Could you please help me with the same issue? The difference is that Odin doesn't recognize when I plug in my phone! I don't know what else to do. It's a G530H.
Thank you very much!
Click to expand...
Click to collapse
Is your USB cable original is it working on other devices? And are you using a USB 2.0 port, that is very much necessary, for Odin and some other hardware/software environment applications. And you also must have Samsung USB drivers installed in your PC, you can also try all this process on some other PCs
Sent from my SAMSUNG-SM-G920A using Tapatalk
talvigi said:
Is your USB cable original is it working on other devices? And are you using a USB 2.0 port, that is very much necessary, for Odin and some other hardware/software environment applications. And you also must have Samsung USB drivers installed in your PC, you can also try all this process on some other PCs
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Hello!
Yes, that USB works with other phones. And even not being the original one, it was working to transfer files before this issue...
It is a USB 2.0 port, and even when I go to "Device Manage" on Windows, it doesn't show any port with an unknown device or something like that...
Thanks!
Security error:This phone has been flashed with unauthorized software & is locked.
Hello everyone. I have Samsung Galaxy S5e and I tried twrp flashing.
After tablet couldn't start and boot loop.
I tried to clear cache and reboot.
After reboot i got a error,
Security error:This phone has been flashed with unauthorized software & is locked. Call you mobile operator for additional support.
Now i can not do anything.
No recovery no download mode nothing.
Please help me.....
This is the image link because i can't upload picture here.
https://ibb.co/yNvwh7P
You will need to download the original firmware and reflash with Odin, that will fix this error.
Edit: You can get it into download mode, just keep trying...
babafooka said:
Hello everyone. I have Samsung Galaxy S5e and I tried twrp flashing.
After tablet couldn't start and boot loop.
I tried to clear cache and reboot.
After reboot i got a error,
Security error:This phone has been flashed with unauthorized software & is locked. Call you mobile operator for additional support.
Now i can not do anything.
No recovery no download mode nothing.
Please help me.....
This is the image link because i can't upload picture here.
https://ibb.co/yNvwh7P
Click to expand...
Click to collapse
To enter 'Download Mode' and recover from the error:
Connect a USB cable to your Laptop/PC.
With power-off on the device, hold down BOTH 'Volume Up' and 'Volume Down'.
Connect the USB cable to the device, while holding down both volume keys, and press 'Power'.
If done correctly, the device will boot to 'Download Mode'.
Hi. Thank you for replying but it doesn't help. Every time i get same screen.
Believe me i did correctly.
nsx2brz said:
You will need to download the original firmware and reflash with Odin, that will fix this error.
Edit: You can get it into download mode, just keep trying...
Click to expand...
Click to collapse
Sir i can not enter in download mode.
babafooka said:
Sir i can not enter in download mode.
Click to expand...
Click to collapse
Mine did that once to me, try following the instructions and be persistant...
I am soo stupid. I brocked my tablet after unsuccessful attempts. Last week I bought new same tablet and happened again same situation after update magisk menager.
I tried your method and it works. I love you so much. You saved me.
Last time didn't work because laptop usb port was defective. I brocked 450€ tablet.
nsx2brz said:
Mine did that once to me, try following the instructions and be persistant...
Click to expand...
Click to collapse
You can flash with odin on the warning screen
PetiHun08 said:
You can flash with odin on the warning screen
Click to expand...
Click to collapse
Bro its literally easy
I have flashed tweaked rom on my SM-T820. It worked for a good 6 months and then this error has started to happen. Can reboot once or twice then the security error happens. I then need to reflash original firmware and then twrp, tweaked and repeat. Is there a way to stop this happening?
TiTiB said:
To enter 'Download Mode' and recover from the error:
Connect a USB cable to your Laptop/PC.
With power-off on the device, hold down BOTH 'Volume Up' and 'Volume Down'.
Connect the USB cable to the device, while holding down both volume keys, and press 'Power'.
If done correctly, the device will boot to 'Download Mode'.
Click to expand...
Click to collapse
***Moderator Edit: Translation provided***
And if this is done, the cell phone data, photos, etc. are not deleted?
Spoiler: Spanish
Y si se hace esto no se borran los datos del celular, fotos,etc.??
RaulValles21 said:
***Moderator Edit: Translation provided***
And if this is done, the cell phone data, photos, etc. are not deleted?
Spoiler: Spanish
Y si se hace esto no se borran los datos del celular, fotos,etc.??
Click to expand...
Click to collapse
Please use English on XDA, per Article 4 of the Forum Rules.
Booting into download mode will not wipe data.
thanks
I have the same problem after trying to flash TWRP on a sm-t295 - tab A.
It seems I need to flash the original firmware - T295XXU4CUF7.
Do you know where can I get it? UK variant.
Thanks