Hi there ,
My phone keeps rebooting every time I connect it to the pc
Build Nr JSS15J.I9505XXUEMK9
BaseBand I9505XXUEMK9
Android 4.3
Anyone had this And how to fix it
cheers for any help
Try reinstalling your phones USB drivers. Does your phone only crash with Android debugging turned on? Try connecting to a rear USB port (rear USB port on computer output more mAh than front USB ports). Try another cable. If it still crashes check the phones micro USB port as it could be faulty.
Sent from my GT-I9505 using Tapatalk
Also try a different cable.
retrotronic said:
Try reinstalling your phones USB drivers. Does your phone only crash with Android debugging turned on? Try connecting to a rear USB port (rear USB port on computer output more mAh than front USB ports). Try another cable. If it still crashes check the phones micro USB port as it could be faulty.
Sent from my GT-I9505 using Tapatalk
Click to expand...
Click to collapse
turned debugging on installed usb drivers but yellow
Lennyz1988 said:
Also try a different cable.
Click to expand...
Click to collapse
Took sd card out replaced it now its working again cheers guys :fingers-crossed:
Related
The probem:
USB Mass Storage not working in Recovery. I tried everything, reflashing different recovery but its not working, it doesn't give an error message. When card is not inside however it does complain. SdCard is fine because I can flash zips that are on it. Tested on both windows and ubuntu. tried another card as well
USB Mount doesn't work in CM7.2 or any rom or nand restore i've done recently. I had Insomnia at some point, then inferno, then cm 7.1, none of these restores work. Again here no errors, I do not even see the sign for usb detection. usb debugging is enabled/disabled no difference. phone however still charges though.
I'm on a trip right now, but I've not had the chance yet to get another usb cable but the two I have dont work.
katsumeiyo said:
The probem:
USB Mass Storage not working in Recovery. I tried everything, reflashing different recovery but its not working, it doesn't give an error message. When card is not inside however it does complain. SdCard is fine because I can flash zips that are on it. Tested on both windows and ubuntu. tried another card as well
USB Mount doesn't work in CM7.2 or any rom or nand restore i've done recently. I had Insomnia at some point, then inferno, then cm 7.1, none of these restores work. Again here no errors, I do not even see the sign for usb detection. usb debugging is enabled/disabled no difference. phone however still charges though.
I'm on a trip right now, but I've not had the chance yet to get another usb cable but the two I have dont work.
Click to expand...
Click to collapse
Its either your USB cable or your phone USB jack mine does the same thing I have to wiggle it to get a good connection cuz my USB cable sucks cuz with others it recognizes it right away.
...Awesome... said:
Its either your USB cable or your phone USB jack mine does the same thing I have to wiggle it to get a good connection cuz my USB cable sucks cuz with others it recognizes it right away.
Click to expand...
Click to collapse
He has tried two cables, so I would tend to lean toward the port.
Sent from my HTC Glacier using XDA
i am in the same boat. looks like my charging port is bad. anyway to replace the charging port? i am not good with soldering
it's not ur usb port
it's htc.. htc devices doesn't support usb host feature.
If you have a rom and kernal that do support usb host then try powering the usb as the htc devices do not provide power out.. use usb Y cable
tempuser2005 said:
it's htc.. htc devices doesn't support usb host feature.
If you have a rom and kernal that do support usb host then try powering the usb as the htc devices do not provide power out.. use usb Y cable
Click to expand...
Click to collapse
What? He isn't trying to host the connection. He is trying to use his phone as a USB mass storage device.
Where did you get USB host from in his questions?
Sent from my HTC Glacier using XDA
Hi all,
I am having the same problem, except perhaps with a different cause. My user account on Windows 7 became corrupt and I can no longer log in, so I had to create a new one.
On the new account, my myTouch 4G is not recognized for mass storage/disk drive mode via USB. The USB cable does work, the port is okay, and I've used both with other devices. The myTouch shows as charging when connected to the computer. I have uninstalled and reinstalled all of the myTouch drivers, restarted computer and phone, to no avail.
When it is connected in USB, it shows as generic "Drive F" and is inaccessible. When I check properties it says mytouch4g. When I check "Devices" it is recognized as portable storage. I have tried with USB debugging on and off, and have set "connected to computer" mode to disk drive.
Any thoughts? I thought possibly loading the generic ADB driver again might help, but I cannot get to the stage where I can force it to load that driver instead of the HTC one.
My S4 does not show up in My Computer, it normally shows up and I can click it and go into either my phone drive or SD drive, but now nothing.
USB Debugging is on, and the phone does charge. I tried reinstalling the drivers, restarting the phone while plugged in, and I do not have a USB utilities option. Android version 4.2.2.
It sounds like a computer issue. Wipe your hard drive and re install windows that should clear it up and have your phone showing up again. Otherwise your phone is infected with the samsung virus and I can actually fix that for you if you PM me your details.
ss_gohan said:
My S4 does not show up in My Computer, it normally shows up and I can click it and go into either my phone drive or SD drive, but now nothing.
USB Debugging is on, and the phone does charge. I tried reinstalling the drivers, restarting the phone while plugged in, and I do not have a USB utilities option. Android version 4.2.2.
Click to expand...
Click to collapse
Bad usb cable or port. Try a different cable or a different usb port. Not all usb cables can pass data, some only charge. It is always best to use the cable that came with the phone when transferring data via usb.
cruise350 said:
Bad usb cable or port. Try a different cable or a different usb port. Not all usb cables can pass data, some only charge. It is always best to use the cable that came with the phone when transferring data via usb.
Click to expand...
Click to collapse
I use the cable that came with the phone, it was working before.
What kernel? If KT uncheck fast charge in kttweaker app under extras.
SGS4 Sent
ifly4vamerica said:
What kernel? If KT uncheck fast charge in kttweaker app under extras.
SGS4 Sent
Click to expand...
Click to collapse
Kernel version 3.4.0-95334
Anyone know how to fix this?
I'm having trouble connecting my N9005 to my pc using Windows8. The problem is it does not recognize the phone's storage and is not able to mount it.
I've tried installing Samsung Universal USB Drivers to no avail.
My laptop only has USB2 ports and if I'm correct N9005 utilizes USB v3. Could it be the cause?
I also have the same problem in Ubuntu.
I also tried Samsung Kies and it doesn't work either.
Upon connecting, my PC recognizes that the phone's been connected but it's not able to mount the storage.
NoobSibot said:
I'm having trouble connecting my N9005 to my pc using Windows8. The problem is it does not recognize the phone's storage and is not able to mount it.
I've tried installing Samsung Universal USB Drivers to no avail.
My laptop only has USB2 ports and if I'm correct N9005 utilizes USB v3. Could it be the cause?
I also have the same problem in Ubuntu.
I also tried Samsung Kies and it doesn't work either.
Upon connecting, my PC recognizes that the phone's been connected but it's not able to mount the storage.
Click to expand...
Click to collapse
The Note 3 mounts as an MTP drive. Make sure you have it selected under the drive connection settings on your phone.
In some cases enabling USB Debugging in Developer Settings would allow for the USB to mount.
nicholaschum said:
The Note 3 mounts as an MTP drive. Make sure you have it selected under the drive connection settings on your phone.
In some cases enabling USB Debugging in Developer Settings would allow for the USB to mount.
Click to expand...
Click to collapse
No difference there my friend.
NoobSibot said:
No difference there my friend.
Click to expand...
Click to collapse
By any chance do you have any unknown devices listed in the Computer Management of your computer?
My Note 3 mounts normally
nicholaschum said:
By any chance do you have any unknown devices listed in the Computer Management of your computer?
My Note 3 mounts normally
Click to expand...
Click to collapse
I don't know what really happened but this last time I connected the device, it mounted normally!
But there's still an unknown Mass Storage Controller in my Device Manager.
unable to connect
Hi,
Perhaps W8 assigned the wrong driver...or a bad / damaged usb cable(?)
Try a system restore to an earlier date
I allways connect my mobile device thru wifi and it's fine
Cheers,
USB3 is backwards compatible with USB2, don't worry about that.
Did you try another cable? You can use any microUSB 2.0 cable, it fits into the right side of the USB port. (the small left bit is the USB3 part.)
Did you unlock the screen when you connect the phone? It can't mount the storage, if you use a lockscreen setting other than none or swipe, until you unlock the screen.
Send From My Samsung Galaxy Note 3 N9005 Using Tapatalk
Hello ShadowLea,
I'm having the same problem on my Samsung Note 3 SM-N9005: "USB device not recognized One of the usb devices connected to this computer has malfunctioned...." when I connect it to my USB3 on my laptop.
I tried the toothpick solution (lifting the tongue of the USB connector on my phone), I tried powering down the Laptop and waiting for 30 seconds to fullly discharge the capacitors, I tried changing 3 different USB cables. I tried different USB ports on Laptop (on USB3 I reiceve the error on the remaining 2 USB2 ports the error does not appear but the phone is not seen by Kies nor Odin.
BTW, FYI, the phone is also having battery charging issues: it only charges if pluggged into the laptop and won't charge if connected to the mains via wall charger (tried 3 different chargers, cables, mains sockets: all work with other devices).
I'm trying to flash a new ROM to try to fix the battery chargin problem but if Odin can't recognize the device...
Also, the dial pad code *#7284# which should give access to the Phone Utility (USB settings) is not working - all other dial pad codes work.
ascanio1 said:
Hello ShadowLea,
I'm having the same problem on my Samsung Note 3 SM-N9005: "USB device not recognized One of the usb devices connected to this computer has malfunctioned...." when I connect it to my USB3 on my laptop.
I tried the toothpick solution (lifting the tongue of the USB connector on my phone), I tried powering down the Laptop and waiting for 30 seconds to fullly discharge the capacitors, I tried changing 3 different USB cables. I tried different USB ports on Laptop (on USB3 I reiceve the error on the remaining 2 USB2 ports the error does not appear but the phone is not seen by Kies nor Odin.
BTW, FYI, the phone is also having battery charging issues: it only charges if pluggged into the laptop and won't charge if connected to the mains via wall charger (tried 3 different chargers, cables, mains sockets: all work with other devices).
I'm trying to flash a new ROM to try to fix the battery charging problem but if Odin can't recognize the device...
Also, the dial pad code *#7284# which should give access to the Phone Utility (USB settings) is not working - all other dial pad codes work.
Click to expand...
Click to collapse
im having the same problem..i try to connect my note 3 via USB cable and is not reading the phone... But for me it start happening after I install the X-NOTE build 18... any Idea how to fix this? Or a link?
xganonx said:
im having the same problem..i try to connect my note 3 via USB cable and is not reading the phone... But for me it start happening after I install the X-NOTE build 18... any Idea how to fix this? Or a link?
Click to expand...
Click to collapse
Hi, I have the same problem with X-Note 18. I tried already all stuff, Odin can see my phone but Kies and any other connection option doesnt help
any update?
any update on this? having the same problem, is it due to xnote?
cussyandrew said:
any update on this? having the same problem, is it due to xnote?
Click to expand...
Click to collapse
Nope, X-Note is fine and I'm using v16 right now without problems.
What I think fixed my problem was using a screwdriver on the usb port on the phone.
I tightened the screws a little bit and it was fine after that.
NoobSibot said:
Nope, X-Note is fine and I'm using v16 right now without problems.
What I think fixed my problem was using a screwdriver on the usb port on the phone.
I tightened the screws a little bit and it was fine after that.
Click to expand...
Click to collapse
well it was working fine on xnote 13, however its been giving me this problem since i updated to xnote 18!!
---------- Post added at 04:21 AM ---------- Previous post was at 04:21 AM ----------
NoobSibot said:
Nope, X-Note is fine and I'm using v16 right now without problems.
What I think fixed my problem was using a screwdriver on the usb port on the phone.
I tightened the screws a little bit and it was fine after that.
Click to expand...
Click to collapse
which screws are you talking about btw?
ive found countless times its a duff or cheap micro USB cable.
if you have been using the genuine Samsung one then it may be faulty. But try another cable.
does any other phone connect ok with the same cable?:good:
I had a similar issue with my note 2 a while back
Sent from my GT-N7100 using XDA Premium 4 mobile app
cussyandrew said:
well it was working fine on xnote 13, however its been giving me this problem since i updated to xnote 18!!
---------- Post added at 04:21 AM ---------- Previous post was at 04:21 AM ----------
which screws are you talking about btw?
Click to expand...
Click to collapse
The ones on the USB port when you remove the back cover.
aladinliverpool said:
ive found countless times its a duff or cheap micro USB cable.
if you have been using the genuine Samsung one then it may be faulty. But try another cable.
does any other phone connect ok with the same cable?:good:
Click to expand...
Click to collapse
No it doesn't connect with any other cable, it charges fine though :/
This problem has already been addressed and solved. Its a problem in the kernel. Download a custom kernel if your using X-note 18.
Wallah, Problem fixed
Dizy801 said:
This problem has already been addressed and solved. Its a problem in the kernel. Download a custom kernel if your using X-note 18.
Wallah, Problem fixed
Click to expand...
Click to collapse
can you please provide links to theses custom kernels?.. im not sure which ones to install
moh277 said:
can you please provide links to theses custom kernels?.. im not sure which ones to install
Click to expand...
Click to collapse
Go download x-note v20. they fixed the problem.
HTML:
http://www.nonsolosmartphone.it/x-note-build-18-0-n9005-nf4-t9278.html
I want to flash roms to my note3, since yesterday i tried everything. problem is i cant use my usb cables to transfer data to my phone. device is not recognized by computers. i tried 5-6 different usb cables some of them work with other devices, tried to remove drivers and reinstall them, tried mac,linux, windows 8.1 device is not recognized. even in download mode when i plug usb cable it charges only. i crawled through google found some kernel related problems which i cant do anything about it without working usb cable, i think my usb port might be broken somehow.i don't wanna buy usb port flex cable if there are any other solutions.
sercankd said:
I want to flash roms to my note3, since yesterday i tried everything. problem is i cant use my usb cables to transfer data to my phone. device is not recognized by computers. i tried 5-6 different usb cables some of them work with other devices, tried to remove drivers and reinstall them, tried mac,linux, windows 8.1 device is not recognized. even in download mode when i plug usb cable it charges only. i crawled through google found some kernel related problems which i cant do anything about it without working usb cable, i think my usb port might be broken somehow.i don't wanna buy usb port flex cable if there are any other solutions.
Click to expand...
Click to collapse
As you said the cables work for other phones so they're not usb3/original note 3 cable?
Sent from my SM-N920C
Rosli59564 said:
As you said the cables work for other phones so they're not usb3/original note 3 cable?
Sent from my SM-N920C
Click to expand...
Click to collapse
one of them is note 4 original cable, also i have note 3 original cable all of them wont work
MicroUSB connector may be damaged. You should be able to use adapter to connect the MicroSDHC card to a PC, copy the new ROM etc. to the card and install from there.
dutch55 said:
MicroUSB connector may be damaged. You should be able to use adapter to connect the MicroSDHC card to a PC, copy the new ROM etc. to the card and install from there.
Click to expand...
Click to collapse
I think that he would not be able to install a new ROM from the card, as he would need a custom recovery that in this case can't be installed, because the phone is not detected by the computer.
To anyone faces similar problem, i have replaced usb charging port and problem solved. its very easy to do.
sercankd said:
To anyone faces similar problem, i have replaced usb charging port and problem solved. its very easy to do.
Click to expand...
Click to collapse
Glad you were able to replace the USB port on the phone. regarding being able to do the first install of a rom without a PC, if you can get root (in the case of an AT&T Note3, with Towelroot), then I believe you can use MobileODIN to install ROMs without a PC.
I had a different phone, a Samsung Galaxy S with a damaged USB port with no data connectivity that a repair shop was unable to repair it.
Hi Basically plugged my S4 i9505 in via usb. Nothing shows in my computer, but phone remains charging. I have tried uninstalling and reinstalling all samsung usb drivers but it does nothing. Tried installing kies/older usb drivers, still no luck. Regardless of if there are drivers or not on my pc, there is no detection what so ever. My pc is detecting my second S4 I9505 perfectly. Anyone know the solution to this?
majorr92 said:
Hi Basically plugged my S4 i9505 in via usb. Nothing shows in my computer, but phone remains charging. I have tried uninstalling and reinstalling all samsung usb drivers but it does nothing. Tried installing kies/older usb drivers, still no luck. Regardless of if there are drivers or not on my pc, there is no detection what so ever. My pc is detecting my second S4 I9505 perfectly. Anyone know the solution to this?
Click to expand...
Click to collapse
Tap 5 times buildnumber in settings menu under: about phone to open developer settings. Enable USB debugging. Now you can choose what to do when phone is plugged in pc.
lekiaM said:
Tap 5 times buildnumber in settings menu under: about phone to open developer settings. Enable USB debugging. Now you can choose what to do when phone is plugged in pc.
Click to expand...
Click to collapse
USB debugging is Enable still nothing happen
USB debugging is not required in order to have the phone recognized by the computer.
Have you tried different USB cables and USB ports? Is the phone detected on other computers?
i had the same problem.... and we found out that the pins or the usb connection sh1t from the phone doesn`t make good contact. si try to push a little but or force up and down the usb cable to the usb from phone maybe you will manage to find a stable connection or something.
when i connect to phone to the pc i have to hold the usb cable connected to the phone in a weird position. that works for me