Related
I have the sprint S4. it was rooted and on stock 4.2.2. i updated it to 4.3 and it went into a bootloop. I then tried reverting to my nandroid from earlier today and now it won't boot at all, it just goes to a screen that says, firmware upgrade encountere an issue. please select recovery mode in kies and try again. there is a list on the top left that says,
current binary:custom
system status:custom
knox kernel lock: 0x0
knox warranty void: 0x1
csb-config-lsd: 0x30
write protection enable
emmc burst mode enable
I need to get this fixed. back to 4.2.2 or 4.3 i honestly don't care at this point. any help would be appreciated. with or without root is fine with me. i can't access recovery anymore, only download mode.
samuelrp1998 said:
I have the sprint S4. it was rooted and on stock 4.2.2. i updated it to 4.3 and it went into a bootloop. I then tried reverting to my nandroid from earlier today and now it won't boot at all, it just goes to a screen that says, firmware upgrade encountere an issue. please select recovery mode in kies and try again. there is a list on the top left that says,
current binary:custom
system status:custom
knox kernel lock: 0x0
knox warranty void: 0x1
csb-config-lsd: 0x30
write protection enable
emmc burst mode enable
I need to get this fixed. back to 4.2.2 or 4.3 i honestly don't care at this point. any help would be appreciated. with or without root is fine with me. i can't access recovery anymore, only download mode.
Click to expand...
Click to collapse
You can try this >>>> to reset to stock MF9 -[ROM][ODIN]SPH-L720 MF9 (MF9 Modem/Kernel/Bootloader/ROM-Rooted) from here:
http://forum.xda-developers.com/showthread.php?t=2486134
Also make sure you read my post #16 in the thread above, other wise you will be in bootloop again.
Good luck
liquid307 said:
You can try this >>>> to reset to stock MF9 -[ROM][ODIN]SPH-L720 MF9 (MF9 Modem/Kernel/Bootloader/ROM-Rooted) from here: http://forum.xda-developers.com/show....php?t=2486134
Good luck
Click to expand...
Click to collapse
Thanks going to try that now. it says not found when i click the link.
samuelrp1998 said:
Thanks going to try that now. it says not found when i click the link.
Click to expand...
Click to collapse
click link on my post.
Here it is again:
http://forum.xda-developers.com/showthread.php?t=2486134
toolyic and
samuelrp1998 said:
I have the sprint S4. it was rooted and on stock 4.2.2. i updated it to 4.3 and it went into a bootloop. I then tried reverting to my nandroid from earlier today and now it won't boot at all, it just goes to a screen that says, firmware upgrade encountere an issue. please select recovery mode in kies and try again. there is a list on the top left that says,
current binary:custom
system status:custom
knox kernel lock: 0x0
knox warranty void: 0x1
csb-config-lsd: 0x30
write protection enable
emmc burst mode enable
I need to get this fixed. back to 4.2.2 or 4.3 i honestly don't care at this point. any help would be appreciated. with or without root is fine with me. i can't access recovery anymore, only download mode.
Click to expand...
Click to collapse
I'm a total noob and did the same thing to my phone but I'm pretty sure this is what you need to fix it http://samsung-updates.com/device/?id=SPH-L720 you can't use MF9 it won't work since you've updated to 4.3. It will take a while to download but just be patient and flash with odin 3.185 :fingers-crossed: Good Luck!
^^ What that person said.
Sent from my SPH-L720 using xda app-developers app
Hi everyone, I'm desperate here.
I was following DJembey's root method TO THE WORD/LETTER. Everything was fine up until the last bit in changing the 'custom' status to official. The triangle away method didn't work, so I downloaded the 'OFFICIAL_STATUS_MOD' and used odin to try and flash the PDA, but it came up as 'FAIL' and now my phone is stuck on boot mode with 'FIRMWARE UPGRADE ENCOUNTERED AN ISSUE'. I've tried using odin to flash back to the stock rom, but it keeps coming up with 'FAIL'. Rally need help
DJembey's root method:
http://forum.xda-developers.com/showthread.php?t=2255190
jesus1987 said:
Hi everyone, I'm desperate here.
I was following DJembey's root method TO THE WORD/LETTER. Everything was fine up until the last bit in changing the 'custom' status to official. The triangle away method didn't work, so I downloaded the 'OFFICIAL_STATUS_MOD' and used odin to try and flash the PDA, but it came up as 'FAIL' and now my phone is stuck on boot mode with 'FIRMWARE UPGRADE ENCOUNTERED AN ISSUE'. I've tried using odin to flash back to the stock rom, but it keeps coming up with 'FAIL'. Rally need help
DJembey's root method:
http://forum.xda-developers.com/showthread.php?t=2255190
Click to expand...
Click to collapse
what firmware you are trying to root, and what stock firmware you tried to flash?
Here's what it says, this is the firmware I am trying to flash, but just before I did the root guide, I applied all of the official updates through settings >about phone > update, etc. It was still on 4.2.2 and I think it was october edition of the latest firmware (in UK)
samersh72 said:
what firmware you are trying to root, and what stock firmware you tried to flash?
Click to expand...
Click to collapse
So maybe I am trying to flash to an older firmware, is this not allowed?? Also, it says that the PIT partition is missing on ODIN (as seen on the attached picture)
jesus1987 said:
So maybe I am trying to flash to an older firmware, is this not allowed?? Also, it says that the PIT partition is missing on ODIN (as seen on the attached picture)
Click to expand...
Click to collapse
i think you have the secured bootloader (check if you have Knox void 0x0 or something in download mode) if yes, you can not go back to MDM or an old firmware, you can flash new "knoxed" firmware.
note that Triangle away and other stuffs to reset counter or status, wont work on new firmware.
samersh72 said:
i think you have the secured bootloader (check if you have Knox void 0x0 or something in download mode) if yes, you can not go back to MDM or an old firmware, you can flash new "knoxed" firmware.
note that Triangle away and other stuffs to reset counter or status, wont work on new firmware.
Click to expand...
Click to collapse
So, when I go into 'proper' download mode (pressing Vol. Down + Home + power) I have:
ODIN MODE
PRODUCT NAME:GT-I9505
CURRENT BINARY:Samsung Official
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID:0x1(or t?)
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION:Enable
And for the 'Firmware upgrade encountered an issue...' screen, I have:
ODIN MODE
PRODUCT NAME:GT-I9505
CURRENT BINARY:Samsung Official
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID:0x1(or t?)
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION:Enable
Hope this helps
jesus1987 said:
So, when I go into 'proper' download mode (pressing Vol. Down + Home + power) I have:
ODIN MODE
PRODUCT NAME:GT-I9505
CURRENT BINARY:Samsung Official
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID:0x1(or t?)
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION:Enable
And for the 'Firmware upgrade encountered an issue...' screen, I have:
ODIN MODE
PRODUCT NAME:GT-I9505
CURRENT BINARY:Samsung Official
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID:0x1(or t?)
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION:Enable
Hope this helps
Click to expand...
Click to collapse
it seems you have the secured bootloder, dont use triangle away or somthing else to reset counter and status.
you can flash firmware that begin only with I9505XXUD or I9505XXUE
samersh72 said:
it seems you have the secured bootloder, dont use triangle away or somthing else to reset counter and status.
you can flash firmware that begin only with I9505XXUD or I9505XXUE
Click to expand...
Click to collapse
At the moment I'm downloading "I9505XXUDMI1-PRE-ROOTED-ODEX-FULL.rar", will this work do you think when I try and flash using ODIN? Hope so!!!
Right, I've tried that firmware, and it's still failing on odin any ideas?
samersh72 said:
it seems you have the secured bootloder, dont use triangle away or somthing else to reset counter and status.
you can flash firmware that begin only with I9505XXUD or I9505XXUE
Click to expand...
Click to collapse
Seems this one doesn't work either...
I've noticed something weird though, I've tried running it a few times, and each time it seems to get a little further in the flash process (it gets to just past modem) then fails.
Hello,
what USB cable are you using?
I have encountered an issue with the original Samsung cable, ("fail" in Odin all the time), but when I switched to another usb cable everything worked from that moment on
Try it, you might have luck.
Zeitraffer said:
Hello,
what USB cable are you using?
I have encountered an issue with the original Samsung cable, ("fail" in Odin all the time), but when I switched to another usb cable everything worked from that moment on
Try it, you might have luck.
Click to expand...
Click to collapse
Funny you should say that...
I restarted my PC, and tried a few USB ports, and cables, and it was still failing. But I stuck at it, and literally doing the same procedure over and over seems to have worked, as it randomly decided to flash fine! This was using the XXUE firmware
Do you still have KNOX WARRANTY 0X1 in download mode?
Sent from my GT-I9505 using XDA Premium HD app
Obagleyfreer said:
Do you still have KNOX WARRANTY 0X1 in download mode?
Sent from my GT-I9505 using XDA Premium HD app
Click to expand...
Click to collapse
Yeah, it still says KNOX WARRANTY VOID 0x1 but it also says the binary and system status are official. Is there a way to unvoid?
I saw this on my bricked GS4 4.3.1(cyanogenmod 10.2) when I powered it on.
Any way to fix this?
It pops up on recovery mode and when I boot it up.
I really just want to get my S4 working again.
Can I just take it into some place like Best Buy or something and they'd help me?
Product Name: SGH-M919
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
Write Protection: Enabled
eMMC BURST MODE enabled
oohrekt said:
I saw this on my bricked GS4 4.3.1(cyanogenmod 10.2) when I powered it on.
Any way to fix this?
It pops up on recovery mode and when I boot it up.
I really just want to get my S4 working again.
Can I just take it into some place like Best Buy or something and they'd help me?
Product Name: SGH-M919
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
Write Protection: Enabled
eMMC BURST MODE enabled
Click to expand...
Click to collapse
Please tell me there is hope for me.
oohrekt said:
I saw this on my bricked GS4 4.3.1(cyanogenmod 10.2) when I powered it on.
Any way to fix this?
It pops up on recovery mode and when I boot it up.
I really just want to get my S4 working again.
Can I just take it into some place like Best Buy or something and they'd help me?
Product Name: SGH-M919
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
Write Protection: Enabled
eMMC BURST MODE enabled
Click to expand...
Click to collapse
If you can boot to recovery, then I wouldn't say it's "bricked."
As for a place like Best Buy helping you, well I don't know their processes but anyone who checks for a warranty claim can't help you in its current state.
Why not just flash a new ROM?
oohrekt said:
I saw this on my bricked GS4 4.3.1(cyanogenmod 10.2) when I powered it on.
Any way to fix this?
It pops up on recovery mode and when I boot it up.
I really just want to get my S4 working again.
Can I just take it into some place like Best Buy or something and they'd help me?
Product Name: SGH-M919
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
Write Protection: Enabled
eMMC BURST MODE enabled
Click to expand...
Click to collapse
If your phone is "bricked" than your phone has the same exact functionality as a brick. If your phone can turn on and tell you which version of android your on, well... a brick cant do that.
Well I can't get into recovery mode. Being the idiot I tried to flash 4.2.2 over not thinking what I have done. Well, even before I couldn't get into recovery mode. I can get into download mode however. Is it possible I can flash official 4.3 or some other 4.3.1 rom over?
If you still having the problem..
oohrekt said:
Well I can't get into recovery mode. Being the idiot I tried to flash 4.2.2 over not thinking what I have done. Well, even before I couldn't get into recovery mode. I can get into download mode however. Is it possible I can flash official 4.3 or some other 4.3.1 rom over?
Click to expand...
Click to collapse
Well friend,
don't panic.. as I know all your loses is that you lost your warranty but not your device..
You can install the stock original rom jelly bean 4.3
If you are interested go to www sammoblie com then (firmwares) then search for your device model (I9500) or (I9505) or (I9505G) or (I9506) then download the firmware for your country and carrier and follow their installing instructions
If you can boot to recovery, then I wouldn't say it's "bricked."
As for a place like Best Buy helping you, well I don't know their processes but anyone who checks for a warranty claim can't help you in its current state.
Why not just flash a new ROM?
DUBU said:
If you can boot to recovery, then I wouldn't say it's "bricked."
As for a place like Best Buy helping you, well I don't know their processes but anyone who checks for a warranty claim can't help you in its current state.
Why not just flash a new ROM?
Click to expand...
Click to collapse
bro cant you read that he cant boot into recovery
---------- Post added at 09:58 AM ---------- Previous post was at 09:54 AM ----------
oohrekt said:
Well I can't get into recovery mode. Being the idiot I tried to flash 4.2.2 over not thinking what I have done. Well, even before I couldn't get into recovery mode. I can get into download mode however. Is it possible I can flash official 4.3 or some other 4.3.1 rom over?
Click to expand...
Click to collapse
did you ever fix it , i got the exact same problem , i got a metropcs s4 and i wanted kit kat insane rom and tried to flash a stock tmobile rom because some people said they did and it was fine,. well not for me. i would like to knowif you ever got it fixed, i tried to flash the stock metropcs 4.2.2 that i was on before this happened and odin still fails.
its fixed now , i had to move the stock tar to the same folder as odin, go figure
Haha mate you havent "bricked" your phone.
If your phone enters the recovery, it would be booting into the download mode too.
Try getting the official firmware of your specific phone model nom and just flash it via odin.
Dont worry.
Sent from my GT-I9500 using XDA Free mobile app
DeepankarS said:
Haha mate you havent "bricked" your phone.
If your phone enters the recovery, it would be booting into the download mode too.
Try getting the official firmware of your specific phone model nom and just flash it via odin.
Dont worry.
Sent from my GT-I9500 using XDA Free mobile app
Click to expand...
Click to collapse
I get a message about use kies recovery because firmware upgrade had issues when I try to boot into recovery, and I when I boot download mode flashing the stock rom fails every time.
revized said:
I get a message about use kies recovery because firmware upgrade had issues when I try to boot into recovery, and I when I boot download mode flashing the stock rom fails every time.
Click to expand...
Click to collapse
Yeah that is because you upgraded to 4.3 which has KNOX bootloader.
It wont let you flash 4.2.2 anymore. Like a downgrade is not possible once a knix enavled bootloader is flashed.
Download 4.3 or 4.4.2 and flash. It wont fail.
Thanks if i helped.
Sent from my GT-I9500 using XDA Free mobile app
DeepankarS said:
Yeah that is because you upgraded to 4.3 which has KNOX bootloader.
It wont let you flash 4.2.2 anymore. Like a downgrade is not possible once a knix enavled bootloader is flashed.
Download 4.3 or 4.4.2 and flash. It wont fail.
Thanks if i helped.
Sent from my GT-I9500 using XDA Free mobile app
Click to expand...
Click to collapse
Sounds nice and all although I tried to flash the official 4.3 from Samsmobile and it's fails.
4.4 is not available for mrtropcs customers because the company don't care about it's customers in this regard. LOL
Just for inquiry purposes only, I found a link to a Guy saying he used lunix to delete know bootloader from a tar filehttps://www.google.com/url?sa=t&source=web&rct=j&ei=8PDgU7DSOZTdoATTkIKYDA&url=http://m.youtube.com/watch%3Fv%3D75DKAGNstbM&cd=1&ved=0CB4QtwIwAA&usg=AFQjCNE7yajeB0317RtOmlFeEIB1QgEOGA&sig2=oD8TmSaTKu19-kpy0AKFGQ
Just go to sammobile and find the latest firmware for your model (4.4.2 for example) and dont look at build number.
Just grab it and extract to desktop.
Put your device in recovery mode if you can, and wipe data/cache/system if you can.
Then put your phone in download mode and connect do computer, in ODIN choose AP and add your tar.md5 file from desktop.
Flash it.
Then pull out battery on first reboot when flashin. Put it back and get into recovery by pressing VolUp + Power. Wipe everything again and reboot.
Should be fine.
i was finally able to flash stock 4.3 by just moving the tar file into the same folder as odin, go figure , i still want 4.4!!LOL
Can someone help with a possible bricked an SGH-i337 4.3 UCUEMK2 build?
Got this on eBay & it "ran" great but this nagging voice kept saying, "it could be better on KitKat."
First let me say I’ve been rooting & flashing ROMs for years but this had me stumped.
After performing a successful "saferoot" I found RomManager couldn’t install ColckworkMod due to a locked bootloader.
I did install "Safestrap" but w/o fully understanding how to use it I may have killed it.
As of now I cannot boot into recovery, normal booting shows the Samsung logo with an unlocked padlock symbol.
Odin connects but with a locked bootloader I’m not sure if that will help since NAND write fails.
In download mode at the triangle screen this is what it reads:
PRODUCT NAME: SGH-I337
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
Knox Kernel Lock: 0x0
Knox Warrantee Void: 0x0
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC Burst Mode enabled
Any Devs out there that can prevent this from becoming an aquarium chew toy please help.
I’ve been trying to fix it for 2 weeks & about to give-up.
much thanks, Rick
You will be able to flash the full MK2 firmware using odin
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Thanks jmjoyas
jmjoyas said:
You will be able to flash the full MK2 firmware using odin
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Click to expand...
Click to collapse
I've been looking for the modem/radio MD5 file but no luck so far. Even if I do find it I'm not sure if my locked bootloader will let me flash it.
rfreynolds said:
I've been looking for the modem/radio MD5 file but no luck so far. Even if I do find it I'm not sure if my locked bootloader will let me flash it.
Click to expand...
Click to collapse
Try here http://forum.xda-developers.com/showthread.php?p=49562527
Sent from my SAMSUNG-SGH-I727
MANY THANKS to jmjoyas & jd1639
after following your advice all is back to normal & backed up. now i need to study safestrap & push on to kitkat. thanks again guys.
please help. I had wifi on last night at home, i saw att pushed through an update but I couldn't stop it. it says updating management files.
when the phone tried to reboot, I got stuck on
Could not do normal boot.
ODIN MODE
PRODUCT NAME: SGH-I337
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICIAL
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X0
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION ENABLE
EMMC BURST MODE ENABLED
Downloading... do not turn off target!! screen
please help, what should i do now?
I take it that it won't reboot now? Do you know what firmware version you were on before the ota update?
Sent from my Nexus 5 using XDA Free mobile app
hotwell said:
please help. I had wifi on last night at home, i saw att pushed through an update but I couldn't stop it. it says updating management files.
when the phone tried to reboot, I got stuck on
Could not do normal boot.
ODIN MODE
PRODUCT NAME: SGH-I337
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICIAL
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X0
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION ENABLE
EMMC BURST MODE ENABLED
Downloading... do not turn off target!! screen
please help, what should i do now?
Click to expand...
Click to collapse
Is there a blue bar on the bottom?
Download Odin and choose a package from
http://forum.xda-developers.com/showthread.php?t=2616221
I would choose NB1 tr rootable version
http://forum.xda-developers.com/showthread.php?t=2674223
Reflash your firmware, you will loose all data but hey, your phone will work again
autonomousperson said:
Download Odin and choose a package from
http://forum.xda-developers.com/showthread.php?t=2616221
I would choose NB1 tr rootable version
http://forum.xda-developers.com/showthread.php?t=2674223
Reflash your firmware, you will loose all data but hey, your phone will work again
Click to expand...
Click to collapse
You're probably right. But are you sure he's not on mdl firmware? It would really suck if he is and he updated to nb1
Sent from my Nexus 5 using XDA Free mobile app
True, I guess he can just restore to MDL firmware...
He was in the middle of a update so I was just assuming that the BL is already locked
i don't remember the firmware. it was rooted with towelroot. it gets stucked with the screen that says downloading, do not turn off. no loading bar.
Just do a factory restore with odin... You will loose all your data! But I dont see any other way unless you have a unlocked bl and a custom recovery.
autonomousperson said:
Download Odin and choose a package from
http://forum.xda-developers.com/showthread.php?t=2616221
I would choose NB1 tr rootable version
http://forum.xda-developers.com/showthread.php?t=2674223
Reflash your firmware, you will loose all data but hey, your phone will work again
Click to expand...
Click to collapse
i tried to recovery with odin nb1 tr rootable version. when everything was completed, it says failed. on the screen, i see a msg telling me to get on recovery mode and connect to kies for recovery. I connected to kies, nothing can be detected... help please
finally got it to work! after i ran nb1 tr rootable version, it failed, then i did more digging and ran pit from this thread! http://forum.xda-developers.com/showthread.php?t=2404970
got it to work!
I guess your partitions were messed up if you needed to flash a pit file to fix it
autonomousperson said:
I guess your partitions were messed up if you needed to flash a pit file to fix it
Click to expand...
Click to collapse
before i flashed pit, i tried to flash stock firmware as suggested. no go. then flashed pit, it booted. root was removed. samsung keyboard failed to load. i tried to flash the stock firmware again but it still crash and failed to boot. i had to flash pit again... help please!!!
hotwell said:
before i flashed pit, i tried to flash stock firmware as suggested. no go. then flashed pit, it booted. root was removed. samsung keyboard failed to load. i tried to flash the stock firmware again but it still crash and failed to boot. i had to flash pit again... help please!!!
Click to expand...
Click to collapse
Did you try to root it afterwards? I thought you got it to work. What did you do to kill it?
autonomousperson said:
Did you try to root it afterwards? I thought you got it to work. What did you do to kill it?
Click to expand...
Click to collapse
omg! finally flashed stock firmware!!! my oem cable was bad!!!!! I used another cable!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! took me a whole week before I had time to fix this bs! thank you everyone for your supports!
Haha I was just about to suggest that.. You have no idea how many times ive flipped tables trying to figure out what drivers are not working when it was the cable all along