Database Users

Cynaogenmod 10.2 modem not working after fresh install

Performed a full clear and freshly installed the latest nightly and I'm not getting any cell service. any ideas? in about phone it says UNKNOWN on baseband

details
Dadealus said:
Performed a full clear and freshly installed the latest nightly and I'm not getting any cell service. any ideas? in about phone it says UNKNOWN on baseband
Click to expand...
Click to collapse
Let me guess. You have TWRP and when you went into recovery you did more than just swipe to flash. You found a wipe data that prompted you to confirm yes or no and you tapped "yes".
How close am I?

fukenbiker said:
Let me guess. You have TWRP and when you went into recovery you did more than just swipe to flash. You found a wipe data that prompted you to confirm yes or no and you tapped "yes".
How close am I?
Click to expand...
Click to collapse
I have PhilZ touch 5 recovery
To perform a fresh install I chose
wipe data/factory reset> clean to install a new rom
from there I installed the 10.2 nightly and then the 10.2 compatible Gapps
after reboot everything except cell service and camera.
I just now gave up on 10.2, returned to the last 10.1 nighty by performing the same steps
wipe data/factory reset> clean to install a new rom
from there I installed the 10.1 last nightly and then the 10.1 compatible Gapps
after reboot everything works just dandy.

Dadealus said:
I have PhilZ touch 5 recovery
To perform a fresh install I chose
wipe data/factory reset> clean to install a new rom
from there I installed the 10.2 nightly and then the 10.2 compatible Gapps
after reboot everything except cell service and camera.
I just now gave up on 10.2, returned to the last 10.1 nighty by performing the same steps
wipe data/factory reset> clean to install a new rom
from there I installed the 10.1 last nightly and then the 10.1 compatible Gapps
after reboot everything works just dandy.
Click to expand...
Click to collapse
Thank you for the report.

fukenbiker said:
Thank you for the report.
Click to expand...
Click to collapse
Did I do something wrong? that caused the cell modem to stop working? I'd still like to use 10.2 but I'm not sure what I did wrong

Dadealus said:
Did I do something wrong? that caused the cell modem to stop working? I'd still like to use 10.2 but I'm not sure what I did wrong
Click to expand...
Click to collapse
I am learning right along with you, thank you for testing CM 10.2 as I've always liked cyanogenmod but I am sticking with GoldenEye for now because of reports like yours.

It has been seen with a few others using PhilZ and flashing 4.3. Please change recoveries, or update to PhilZ 5.11.0

Ol' Dirty Bastard said:
It has been seen with a few others using PhilZ and flashing 4.3. Please change recoveries, or update to PhilZ 5.11.0
Click to expand...
Click to collapse
I will give this a try and report back

doesnt appear to be a 5.11 for the ATT version

anyone know or have 5.11 loki'd for the ATT s4? This is the only recovery i can find that supports exFAT.

[Q] Slimrom 4.3 freezes on reboot (mako)

Hey guys,
I'm not a total scrub at flashing roms and there's still a bunch of things that I don't understand. I'm pretty positive that I flashed Slimrom correctly but here's the situation.
Started on 4.2.2 Slimrom
Reboot to TWRP recovery
Format factory reset/format data, system, cache, dalvik cache
Flash Slimrom 4.3 stable build 1
Successfully reboots into 4.3
Okay now here's the weird part.
The first time I rebooted back into recovery to flash gapps. After I flashed gapps and tried to reboot into the rom, the phone freezes at the screen with "google" and the unlock sign on the bottom. The only way I can get it to boot into the rom again is if I reformat/reset EVERYTHING (including format data) and reflash 4.3. After a few tries of messing around with not wiping dalvik/cache and stuff I realized that even if I don't flash gapps it still freezes on the google screen. So here's my main problem
After flashing 4.3 slimrom, the phone boots into the rom only once. If I try restarting my phone it freezes on the "google" screen.
Anyone know what I'm doing wrong?
Just to clarify it's a LG Google Nexus 4 mako.
Sorry if I'm being redundant. I just want to give as much detail as possible. If you need anymore info let me know!
Thanks

ms3195 said:
Hey guys,
I'm not a total scrub at flashing roms and there's still a bunch of things that I don't understand. I'm pretty positive that I flashed Slimrom correctly but here's the situation.
Started on 4.2.2 Slimrom
Reboot to TWRP recovery
Format factory reset/format data, system, cache, dalvik cache
Flash Slimrom 4.3 stable build 1
Successfully reboots into 4.3
Okay now here's the weird part.
The first time I rebooted back into recovery to flash gapps. After I flashed gapps and tried to reboot into the rom, the phone freezes at the screen with "google" and the unlock sign on the bottom. The only way I can get it to boot into the rom again is if I reformat/reset EVERYTHING (including format data) and reflash 4.3. After a few tries of messing around with not wiping dalvik/cache and stuff I realized that even if I don't flash gapps it still freezes on the google screen. So here's my main problem
After flashing 4.3 slimrom, the phone boots into the rom only once. If I try restarting my phone it freezes on the "google" screen.
Anyone know what I'm doing wrong?
Just to clarify it's a LG Google Nexus 4 mako.
Sorry if I'm being redundant. I just want to give as much detail as possible. If you need anymore info let me know!
Thanks
Click to expand...
Click to collapse
Are you flashing the right Gapps package? Be sure you are flashing the latest 4.3 one.

abaaaabbbb63 said:
Are you flashing the right Gapps package? Be sure you are flashing the latest 4.3 one.
Click to expand...
Click to collapse
Yep I'm positive. I redownloaded both the 4.3 rom and gapps package multiple times just to make sure. Also it doesn't reboot even if I don't flash gapps. Doesn't boot at all if I flash both the rom then gapps at the same time.

bump

then, wipe data/factory reser and flash the stock rom. the rom might be the problem

davinnwilliam said:
then, wipe data/factory reser and flash the stock rom. the rom might be the problem
Click to expand...
Click to collapse
It works for everyone else though. It's Slimrom 4.3 stable build 1.

Rom isn't the problem.Slim rom beta 1(4.3) is super stable. Use any version of twrp recovery other than 2.6.1.0 and wipe system+data,flash slim rom,flash slim gapps,reboot.
Note: if you flashed franco kernel then this may be the issue for your bootloop also you may want to upgrade your bootloader and radio to 4.3 versions(bootloader more important)

Not able to boot on a clean install- i9300 with TWRP 2.8.6.1

Hello,
Trying to install latest PA 'pa_i9300-5.1-20150528.zip' on Galaxy S3 i9300 using TWRP 2.8.6.1.
Zip installs faster, shows no error.
I select the reboot option, it reboots and sits on PA loading logo
I have been using CM12.1 by JustArchi for some time, thought of giving PA a try.

same here, Im also flashing with TWRP2.8.6.1
The pa_i9300-5.1-20150520 version runs well. But the pa_i9300-5.1-20150528 doesnt. It goes directly to TWRP.
wipe, format, factory reset, redownload rom, reflash,.... dont solve.
The same happens when upgrading from Paranoid_OTA app =/

Same here.
But i'm surprised, you say the pa_i9300-5.1-20150520 run well on your I9300 ?
Can you tell me how you managed to make it work ?
I tried a full swipe then install, didn't had any luck, tried differents gapps with no success.
Can you tell me wich Gapps you use please ?

I had tried 'pa_i9300-5.1-20150520.zip' also, it showed the same behavior.
I don't flash gapps on the first go, I boot with just the rom and later reboot into recovery and load all the zips.

mackhdo said:
But i'm surprised, you say the pa_i9300-5.1-20150520 run well on your I9300 ?
Can you tell me how you managed to make it work ?
I tried a full swipe then install, didn't had any luck, tried differents gapps with no success.
Can you tell me wich Gapps you use please ?
Click to expand...
Click to collapse
I ve just followed a tutorial on the internet.
Boot into TWRP, Format, Wipe Cache/Dalvik/System, Install PA, Install GApps, Wipe Cache/Dalvik, and reboot.
And mine is the 5.1.x mini package from there: http://forum.xda-developers.com/paranoid-android/general/5-1-x-5-0-x-4-4-x-pa-gapps-mirror-t3069879

Unable to BOOT
I did a clean installation of PA 5.1 dated 12/6/15. Gapps did well too. Phone reboots and enters CWM again.. did multiple times but it always jumps to CWM. Any guidance Senior Members.

Pretty sure you have to flash a kernel

naveed8695 said:
I did a clean installation of PA 5.1 dated 12/6/15. Gapps did well too. Phone reboots and enters CWM again.. did multiple times but it always jumps to CWM. Any guidance Senior Members.
Click to expand...
Click to collapse
Having exactly the same problem. I can only get the original 5.1 ROM from may to work, but none of the updates. Tried formatting system, cache, dalvik and even tried flashing the boot.img inside the zip file. No luck ?.

YanN509 said:
Having exactly the same problem. I can only get the original 5.1 ROM from may to work, but none of the updates. Tried formatting system, cache, dalvik and even tried flashing the boot.img inside the zip file. No luck ?.
Click to expand...
Click to collapse
You need to flash a different kernel. The boot.img that ships with the rom keeps getting bored during the build it would appear.
This is covered extensively in the g+ community

Pirateghost said:
You need to flash a different kernel. The boot.img that ships with the rom keeps getting bored during the build it would appear.
This is covered extensively in the g+ community
Click to expand...
Click to collapse
Thank you for the advice. :good:
It worked with Boeffla Kernel 12.1 alpha 3 (but the latest ones did not)

pa_i9300-5.1-20150520.zip works!
texmty said:
same here, Im also flashing with TWRP2.8.6.1
The pa_i9300-5.1-20150520 version runs well. But the pa_i9300-5.1-20150528 doesnt. It goes directly to TWRP.
wipe, format, factory reset, redownload rom, reflash,.... dont solve.
The same happens when upgrading from Paranoid_OTA app =/
Click to expand...
Click to collapse
pa_i9300-5.1-20150520.zip works indeed after wipe: dalvik, cache, data, system. then format.
when it successfully boots, restart into recovery and make backup of only "boot" to external_sd.
then format again and factory reset, then install latest zip (pa_i9300-5.1-20150704.zip).
before reboot first restore "boot" from backup.

Tequila4alvin said:
pa_i9300-5.1-20150520.zip works indeed after wipe: dalvik, cache, data, system. then format.
when it successfully boots, restart into recovery and make backup of only "boot" to external_sd.
then format again and factory reset, then install latest zip (pa_i9300-5.1-20150704.zip).
before reboot first restore "boot" from backup.
Click to expand...
Click to collapse
That worked for me too

Samsung s4 i9505 bootloop

Every time I flash cyamogenmod rom in clockwork mod or twrp on my s4 I get stuck on boot symbol. I follow instructions but always fail please help.

Hi,
This thread is being moved to your own dedicated forum , where the experts may be able to help you better.
Good luck!

JaguarBeast said:
Every time I flash cyamogenmod rom in clockwork mod or twrp on my s4 I get stuck on boot symbol. I follow instructions but always fail please help.
Click to expand...
Click to collapse
1. You have to wipe all (system, data, cache and dalvik) before flash Cyanogen Mod.
2. Boot symbol needs time normally (~ 10 min loading the config).

In what order do you wipe everything ?
I do a factory reset, then wipe cache and finally wipe the dalvik cache

That's it, buddy. With emphasis on "FACTORY RESET".
Let's us know if that worked for ya...

Does it matter what custom recovery you have ?
thundastruck said:
That's it, buddy. With emphasis on "FACTORY RESET".
Let's us know if that worked for ya...
Click to expand...
Click to collapse
Is clockworkmod or team win better ?

TWRP. Certain ROMs will not install with Clockworkmod as the recovery.

I want cyamogenmod 12.1 nightly on my s4
Strephon Alkhalikoi said:
TWRP. Certain ROMs will not install with Clockworkmod as the recovery.
Click to expand...
Click to collapse
I have already downloaded the file and placed it on my internal sd card. Which gapps should I chose ?

Android 5.1.1. Which package you desire is up to you. I personally use the nano package.

Bootloop once again
Strephon Alkhalikoi said:
Android 5.1.1. Which package you desire is up to you. I personally use the nano package.
Click to expand...
Click to collapse
I did a factory reset, wiped the cache and dalvik cache. I flashed cyamogenmod alone and it hasn't booted in 20 minutes. Please help

Let's clarify something. What model number shows up when you enter download mode? Also, is it hanging on the Samsung logo or the boot animation?

Stuck at cyamogenmod logo
Strephon Alkhalikoi said:
Let's clarify something. What model number shows up when you enter download mode? Also, is it hanging on the Samsung logo or the boot animation?
Click to expand...
Click to collapse
It gets stuck at cyamogenmod logo and the download mode model number is Samsung MSM8960

Umm, no. The model number should be GT-I9505 or something similar. Regardless, what GApps package are you using? CM12.1 has trouble with some of the GApps packages and bootloops occur because of it.

Sorry the model is i9505
Strephon Alkhalikoi said:
Umm, no. The model number should be GT-I9505 or something similar. Regardless, what GApps package are you using? CM12.1 has trouble with some of the GApps packages and bootloops occur because of it.
Click to expand...
Click to collapse
I have tried to install cyamogenmod 12.1 alone without gapps but had no success.

Something with your phone isn't right. Either you're missing a step in installing Cyanogenmod, or else your phone's internal storage spaces are not configured correctly. I would recommend starting from scratch, meaning installing the latest stock ROM from your carrier. Once you're satisfied that the S4 is working properly with the stock ROM, install TWRP and then install Cyanogenmod.

Already done that XD
Strephon Alkhalikoi said:
Something with your phone isn't right. Either you're missing a step in installing Cyanogenmod, or else your phone's internal storage spaces are not configured correctly. I would recommend starting from scratch, meaning installing the latest stock ROM from your carrier. Once you're satisfied that the S4 is working properly with the stock ROM, install TWRP and then install Cyanogenmod.
Click to expand...
Click to collapse
I've installed the stock rom(lollipop), rooted my phone and used flashify(Google play app) to download and flash recovery(TWRP). Should I use a cyamogenmod nightly or a stable version ?

That's up to you. Development channel ROMs have a greater possibility of bugs that could stop you cold. Release channel ROMs have fewer bugs but generally lag behind the Development channel in terms of bug fixes and, occasionally, features.
I personally use Optimized CM12.1 from AntaresOne.

Could you recommend a custom rom specifically for s4 i9505 ?
Strephon Alkhalikoi said:
That's up to you. Development channel ROMs have a greater possibility of bugs that could stop you cold. Release channel ROMs have fewer bugs but generally lag behind the Development channel in terms of bug fixes and, occasionally, features.
I personally use Optimized CM12.1 from AntaresOne.
Click to expand...
Click to collapse
So I download the rom zip I want in the root of internal storage, go into recovery and do factory reset, wipe cache + dalvik cache. I choose install and select zip I downloaded. What else did I miss ?
P.S Can you flash gapps later on cyamogenmod if it boots ?

Nothing from what I can see. I simply think that the Cyanogenmod ROM you downloaded didn't like your phone. I've had no issues with Optimized CM12.1, which is why I recommended it.
Re GApps: Yes.

Strephon Alkhalikoi said:
Nothing from what I can see. I simply think that the Cyanogenmod ROM you downloaded didn't like your phone. I've had no issues with Optimized CM12.1, which is why I recommended it.
Re GApps: Yes.
Click to expand...
Click to collapse
Boot loop again XD. I followed the instructions exactly in the link below.
http://forum.xda-developers.com/gal...lop/exclusive-antaresone-alucard24-s-t3066696
Must be bad luck or something.

Galaxy S4 i9500 - CM 12.1 Nightly (20160110) - GApps crashing constantly

So today I went from stock 5.0.1 to CM 12.1 Nightly (20160110) but gapps keeps crashing which makes my phone semi useless
First Things first
1. Flashed TWRP using Odin
2. Went into recovery and wiped Data and System
3. Installed CM 12.1
4. Installed GApps
5. Wiped Cache/Dalvik and rebooted
Phone boots up normally, And after unlocking the screen a stream of errors emerges, Not sure if i'm using the right gapps or not
Any help is much appreciated
~Chik

Chikyu Tenshi said:
So today I went from stock 5.0.1 to CM 12.1 Nightly (20160110) but gapps keeps crashing which makes my phone semi useless
First Things first
1. Flashed TWRP using Odin
2. Went into recovery and wiped Data and System
3. Installed CM 12.1
4. Installed GApps
5. Wiped Cache/Dalvik and rebooted
Phone boots up normally, And after unlocking the screen a stream of errors emerges, Not sure if i'm using the right gapps or not
Any help is much appreciated
~Chik
Click to expand...
Click to collapse
Did you by any chance use Opengapps? Opengapps is like a hit or miss. Some days they work and some days then don't.
Try these gapps:
http://download.dirtyunicorns.com/files/gapps/banks_gapps/
You need to perform a full wipe though.

Lennyz1988 said:
Did you by any chance use Opengapps? Opengapps is like a hit or miss. Some days they work and some days then don't.
You need to perform a full wipe though.
Click to expand...
Click to collapse
Yes I did try Opengapps which also didn't work
Edit: The gapps is 6.x.x while my phone is 5.1.1, That won't break my phone will it?
~Chik

You need 5.1 gapps then.

Chikyu Tenshi said:
Yes I did try Opengapps which also didn't work
Edit: The gapps is 6.x.x while my phone is 5.1.1, That won't break my phone will it?
~Chik
Click to expand...
Click to collapse
My bad. Here is also another gapps
http://forum.xda-developers.com/android/software/app-minimal-gapps-gapps-lp-20150107-1-t2997368

Lennyz1988 said:
My bad. Here is also another gapps
Click to expand...
Click to collapse
Still :c I only flashed the base tho, Am I supposed to flash the add ons too?

I think you can try a complete boot before flashing Gapps. And try other builds of Opengapps like mini or micro(well or even smaller depending your "Google apps" usage)

CHIN3S3_N00B said:
I think you can try a complete boot before flashing Gapps. And try other builds of Opengapps like mini or micro(well or even smaller depending your "Google apps" usage)
Click to expand...
Click to collapse
Thanks for the reply, I'm downloading micro right now. Gonna fresh install CM 12.1 using TWRP then boot my phone fully before going back to recovery and flashing Gapps
Will edit my post within 30 mins with the result
Edit: No luck, And now for some reason my phone does not recognise my sim card

Could you try GearCM? Official CM for i9500 had lots of issues.
Sent from my GT-I9500

Chikyu Tenshi said:
Thanks for the reply, I'm downloading micro right now. Gonna fresh install CM 12.1 using TWRP then boot my phone fully before going back to recovery and flashing Gapps
Will edit my post within 30 mins with the result
Edit: No luck, And now for some reason my phone does not recognise my sim card
Click to expand...
Click to collapse
Strange... because the symptoms shows like a mismatched gapps to cm... btw are you using the lastest TWRP?
If Yes try other recoveries. I used to use Philz until I bricked mine and had to flash back to stock and now I'm using a modified TWRP to enable dual boot.
If No then try update it and give it another try?

CHIN3S3_N00B said:
Strange... because the symptoms shows like a mismatched gapps to cm... btw are you using the lastest TWRP?
If Yes try other recoveries. I used to use Philz until I bricked mine and had to flash back to stock and now I'm using a modified TWRP to enable dual boot.
If No then try update it and give it another try?
Click to expand...
Click to collapse
I recommend against doing this. The other recoveries are outdated and will give you problems. Stick with the latest TWRP.

Lennyz1988 said:
I recommend against doing this. The other recoveries are outdated and will give you problems. Stick with the latest TWRP.
Click to expand...
Click to collapse
I think that i didn't express myself very well. Yes it's advisable and strongly recommended to use lastest builds of any recovery available as stable build.
But once i had to use Philz to flash a MIUI ROM because TWRP 2.8.6.0 was unable to execute the installation script didn't know why and that's why i said about different recoveries, and oh.... I forgot to say that after successful install rollback to TWRP because it's pretty new , stable and more user friendly than others.(CMW and the rainbow Easter egg was fine but having to use vol and power keys..... NO THANKS!)