[Q] Micro USB Cable for car charger... - Galaxy S 4 Q&A, Help & Troubleshooting

I'm looking to get a cable for charging my phone in the car...
I've gotten myself a 3.0A charger that my iPad loves to abuse, but I have now tried 4 different cables in the car and my phone is lucky to get anything over 650ma...
Is there something special that needs to be done to the cable? Or perhaps I'm just getting crappy cables?
I used to have an HTC Desire and that was a simple matter of shorting the two middle pins, but that doesn't seem to work for the S4...
Cable needs to be 1.5m (5ft) or so long, so anything in that works at that length would be MUCH appreciated...

TrueTenacity said:
I'm looking to get a cable for charging my phone in the car...
I've gotten myself a 3.0A charger that my iPad loves to abuse, but I have now tried 4 different cables in the car and my phone is lucky to get anything over 650ma...
Is there something special that needs to be done to the cable? Or perhaps I'm just getting crappy cables?
I used to have an HTC Desire and that was a simple matter of shorting the two middle pins, but that doesn't seem to work for the S4...
Cable needs to be 1.5m (5ft) or so long, so anything in that works at that length would be MUCH appreciated...
Click to expand...
Click to collapse
I went on eBay and got a genuine Samsung car charger, charges very fast

I already have a decent charger... three of them actually... the problem I am facing is getting the power from the charger to the phone...

Related

Charging cable - Is it generic?

I'm in the UK and want to save $20 on the charger
I have a couple of Micro USB wall chargers that i use on my blackberry. They will fit the N1 and plug straight into the wall. Would they be safe to use, to charge my N1. (These charges are rated 750mHA).
I know the N1 will be supplied with a micro USB cable. I also have an IPhone wall socket plug head, the ones where you just put the USB cable into the plug and then it goes into the wall. Are these safe to use too, for charging the N1?
Thanks
the Nexus one connector is standar microUSB and therefore will work with standard microUSB cables and chargers.
So there is no type of resistor or transformer in the official plug head? ... to restrict power. I thought there would be as my blackberry charger has a 750mha rating on it.
I can understand the USB cable will work as its a limited power output from a laptop port. But just wanted to check the official wall outlet plug current isn't being restricted. The last thing i want to do is fry my new N1.
Cheers,
Just plugged mine into my old nokia classic micro usb and it is charging fine
The specs for the wall charger are 5V and 1A.
http://www.htc.com/europe/product/nexusone/specification.html
do what i did. remove the charger from your basket and use the supplied USB with an old htc charger if you have one. If not get one for a few quid from ebay why spend $20 when you can get one for $5 odd from the market/ebay.
I can only speak anecdotally, but I used a Blackberry Storm charger and nothing exploded
this mini, micro, A B stuff is annoying. to clarify for my simple mind, will usb cables that fit into my G1 fit into the N1? or is it a different size?
Last year, Micro USB was decided as the open standard for cell phone chargers, so this should be replacing Mini USB as seen on earlier phones (BlackBerries, G1) in instances where the port isn't.. some.. proprietary crap.
Edit:
j.books said:
this mini, micro, A B stuff is annoying. to clarify for my simple mind, will usb cables that fit into my G1 fit into the N1? or is it a different size?
Click to expand...
Click to collapse
No. The G1 used Mini USB, this is Micro USB. The phone comes with a charger and USB (USB-A 2.0 to Micro USB 2.0) cable.
It's not propitary so it will work with any other charger.
It's a funny thing to find. It's too new to be widely available
I went looking for a car charger and a straight USB A->Micro B cable. The former I found by poking in all the packages for different phones until I found it (found a Samsung charger that uses it, although they did want nearly £30 for the damned thing). The USB A->Micro B I drew a blank - the more clueless salesmen tried to convince me that I was mistaken and I meant Mini!
I thought the blackberry used them but I looked in the pile of blackberry cables the local shops had and they were all mini. Even my local electronics store has every kind of USB imaginable *except* micro.
Edit: Found one! (might be useful for UK users). It's out of stock though... http://www.cableuniverse.co.uk/catalog/cables/USB-A-to-Micro-USB-B-Cable.html
Just so you guys know, not all micro USB's are the same. I bought a car charger from a local Tmo store last week (I forget what phones it was for), and although it "worked" when the plug was perfectly perpendicular to the phone, it had quite a bit of lateral play (which the OEM plug does not), meaning anytime it moved in the car, it would stop charging.
I returned it, and am now just waiting for HTC to decide to manufacture accessories for this ever increasing bundle of worry...
I am using a TomTom charger for my N1, also the HTC hero and the Motorola Droid chargers works to charge my N1.
SANTilt said:
Just so you guys know, not all micro USB's are the same. I bought a car charger from a local Tmo store last week (I forget what phones it was for), and although it "worked" when the plug was perfectly perpendicular to the phone, it had quite a bit of lateral play (which the OEM plug does not), meaning anytime it moved in the car, it would stop charging.
I returned it, and am now just waiting for HTC to decide to manufacture accessories for this ever increasing bundle of worry...
Click to expand...
Click to collapse
Seems like it was just a poor quality charger. If it's a micro USB, it should be built to specific specifications. I already bought a few chargers (including a car charger) and cables (for work, home and travel), and they all work perfectly. Technically ALL micro USBs should be the same, unless the manufacturer didn't follow the standards.
TaFFeR said:
Seems like it was just a poor quality charger. If it's a micro USB, it should be built to specific specifications. I already bought a few chargers (including a car charger) and cables (for work, home and travel), and they all work perfectly. Technically ALL micro USBs should be the same, unless the manufacturer didn't follow the standards.
Click to expand...
Click to collapse
Hah, just my luck; I pick up the one out of spec micro USB charger in the entire city!
Although, it must be that particular T-Mobile supplier, as I went to another store and test fitted the same charger, and it had excessive wiggle as well. Either that or my phone is just lame...
I just got a universal charger in Tesco for £5 that has changeable heads (Micro, Mini, Samsung, Sony Ericsson and Nokia 2mm)
Works perfect
- The cable is standard USB. You can use it to charge the phone from your PC, or use another micro USB cable or charger you have
- The Nexus comes with a US 2 pin charger that is dual voltage - works in UK and US. Just spend 50p and get a US to UK convertor plug.
- The charger is rates 5v 1A, so if you have another microUSB charger with the same voltage use that.
I find charging from the charger results in more battery life than USB. The only explanation is charge rate because USB is 500mA and the charger is 1000mA
PS. I removed the UK charger from the order too. You get the US charger regardless in the box.

Samsung USB cable Crap?

Since I have gotten the Epic I have had so many issues with windows seeing the phone and installing the proper drivers even right after restarting the phone. Im lucky if windows see's the phone one out of 10 times I have to plug unplug etc etc until my pc's see the darn phone.
So I caught a post earlier that suggested to try a different cable and BAMM!!! phone links every single time no issues. Im using the usb cable that came with my evo now. Just side by side you can see the huge quality difference.
Samsung might want to check these cables and I suggest if your having charging or communication problems with the phone to try a new cable.
Let me know if any of you are also able to reproduce this!!
Yes. My cable actually broke the 2nd day of owning this phone because it was tugged on a little too hard while i was using my phone with it charging. It wouldn't charge the phone unless it was being pushed upwards or held a certain way.
Pathetic.
I've since been using my girl's MyTouch 3g cable and have had no issues whatsoever.
I just purchased a few new cables from monoprice. I've always had awesome results from them and they are cheap.
Yes the cable that comes with the epic should not be used with a computer IMO. Just look at the charger that plugs into the wall and compare it to the USB pins on your computers case.
The pins are raised a lot higher on the part that plugs into the wall compaired to how raised the pins are on my PC's case. I'm running an antec 1200 and I would consider the front USB ports to be really "tight". I then tried a different cable and have had no problems.......OTHER THAN BATTERY LIFE IN GENERAL sucks on the epic.
I didn't Realize there was a problem with the usb cable on th
e computer side but I have been using my I mac since my pc took a dump b. i think the phone end of the usb cable is just crap.it seems to disconnect really easy and not near as robust as the one that came with my hero. Still love my epic though!
Sent from my SPH-D700 using XDA App
Come on. Both the cable and the wall unit sucks. A phone that is 500 bucks and you give me a .7 amp charger and a cheap ass cable? My HTC touch pro came with a 1 amp charger, that looked nice, and came with a good cable.
syntax_erorr said:
Come on. Both the cable and the wall unit sucks. A phone that is 500 bucks and you give me a .7 amp charger and a cheap ass cable? My HTC touch pro came with a 1 amp charger, that looked nice, and came with a good cable.
Click to expand...
Click to collapse
]
Right? Well at least we got 16g sd cards. They have to give and take you know? lol
my cord works just fine.
However i only have one mini usb (the one that came with it) so i ordered some micro usb to mini usb adapters so i can use all my old cables.
Just order a bunch of microUSB cables from monoprice. It's like $1.20/cable. I ordered 7 so I have a large collection of easily lost cables.
How the hell did I not know about this site? THANKS

Extended USB Cable not charging nexus 7

I tried swapping out the USB cable that came with my nexus 7 with a longer usb cable (still using the same charger though edit: by that, i mean the ASUS charger that came with the N7). It doesn't seem to be charging though, even though it says 'charging' on the screen. When i was using the nexus 7 while plugged in, i actually lost 1% charge after using it for like 30 or so minutes.
I think i grabbed this cable off Ebay. It had no trouble charging my phone. Are there different grades of USB cables or something?
By same charger do you mean the one it came with? The 2 amps charger. Sorry I had to clear that bit up. I think longer cables creates more resistence but I'm not sure if the cable length is significant enough stop charging. I have no idea about grades of USB cables though maybe someone can elaborate on that.
Summerfly said:
By same charger do you mean the one it came with? The 2 amps charger. Sorry I had to clear that bit up. I think longer cables creates more resistence but I'm not sure if the cable length is significant enough stop charging. I have no idea about grades of USB cables though maybe someone can elaborate on that.
Click to expand...
Click to collapse
Yes, the ASUS charger it came with, i plugged in the 6 foot microusb cable i bought off ebay into it.
MFister said:
Yes, the ASUS charger it came with, i plugged in the 6 foot microusb cable i bought off ebay into it.
Click to expand...
Click to collapse
Okay, 6 foot cable doesn't sound excessively long. I have to ask what were you doing on it while charging and what brightness setting was the screen at. Maybe you were draining more power than the charger can provide?
This is pretty common. The stock cable has larger conductors, as I assume other 2 amp chargers come with, and standard cables are sensed somehow and charging current is limited. Try finding a 22awg cable, I think it will work.
I use a USB extender since I don't have any outlets near my bed. I use a cable rated for USB 2.0 and haven't had any problems. I have had problems with cables that aren't. The Motorola USB cables are rated for 2.0 and they all work fine for me with no problems.
burpootus said:
This is pretty common. The stock cable has larger conductors, as I assume other 2 amp chargers come with, and standard cables are sensed somehow and charging current is limited. Try finding a 22awg cable, I think it will work.
Click to expand...
Click to collapse
Thanks, i assume this cable that's 28/24 awg would work?
http://www.monoprice.com/products/p...=10303&cs_id=1030307&p_id=8643&seq=1&format=2
I use a cable extender, but I insert the original stock cable into the tablet (not the charger). It appears to recognise that and charge at the correct rate.
I've tried using a usb extender to charge with the asus charger and the Asus USB cable and checking with battery graph it charges much slower compared to using just the Asus cable.
People with eyesight better than mine will see that the micro USB socket has 5 pins and the Nexus looks at the 5th pin to decide what is connected and what the connected device is allowed to do. The pin can be grounded, not connected (floating) or can be connected to ground via I think 3 fixed resistances. Google for USB on the go. I think that is the standard adopted by Asus and the cable doesn't comply.
I'm using a nook 1/2 cable I got with a car charger for the nooktablet
It works and is longer then the stock cable it came with.
Sent from my Nexus 7 using Tapatalk 2
EE here. I just ran into this issue recently, so I'll share what I learned. Grab a multimeter and measure the resistance of the cable. Check all 4 pins just in case one of them is worse than another.
In my case, I had a really horrible USB extension cable. It measured about 4 Ohms. 4 Ohms is low enough for a multimeter to pass a continuity test, but do out the math:
V = I * R
V = 2A * 8 Ohms (4 Ohms on VCC, 4 Ohms back on GND)
V = 16V.
16 volts?? Where does 16V come from? Short answer: It doesn't. If 2A were actually flowing, the USB cable would have a 16V drop across it. It doesn't though, which tells us that 2A is not flowing. 1A is also not flowing, since that would still be 8V.
0.5 Ohms is a good estimate for a MAXIMUM resistance for a USB charging cable. That's a 1V drop at 2A, meaning the phone is only getting ~4V. That explains why the USB cable that comes with the Nexus 7 is so darn short - it comes in at around 0.1 Ohms (or perhaps less, that's about the limit of what I can accurately measure)
Wanted to get a longer USB cable that will work the Asus adapter, any links?
Thanks.
came across this thread while investigating a strange thing in charging my 4400mah extended battery of my s3.
I have a 5v 1A stock samsung charger with an extension cable i was always using to charge my old phones with a less capacity battery (mugen 3200mah)
This night i spent i wasnt ble to get a full charge from 5% to 100% in 8 hours and this sounds more than strange, but yet understandable.
i will try timings with the stock cable without extension and i'll come back...

1.8 amp car charger

Reading from the AC adapter, this thing can charge at 1.8 amps. I'm doing some research on car chargers that can output 2 amps to the phone via a USB cable, but the trick is getting the phone to pull more than .5 amps from a car accessory outlet. So far I haven't had much luck. There seems to be a lot of info on ipad stuff, but not much in the way of high powered Android devices. So I thought I'd start a thread about compatible car chargers that will allow a full 1.8 amp pull from my car outlet, and see what you guys and gals think and have tried. I've attached a pic of my current setup. It's a Proclip holder on a 2012 Mustang. I've used this same setup for several previous phones (S2 Skyrocket and S3). The holder itself is adjustable to accommodate various phones with cases.
earlthepearl said:
Reading from the AC adapter, this thing can charge at 1.8 amps. I'm doing some research on car chargers that can output 2 amps to the phone via a USB cable, but the trick is getting the phone to pull more than .5 amps from a car accessory outlet. So far I haven't had much luck. There seems to be a lot of info on ipad stuff, but not much in the way of high powered Android devices. So I thought I'd start a thread about compatible car chargers that will allow a full 1.8 amp pull from my car outlet, and see what you guys and gals think and have tried. I've attached a pic of my current setup. It's a Proclip holder on a 2012 Mustang. I've used this same setup for several previous phones (S2 Skyrocket and S3). The holder itself is adjustable to accommodate various phones with cases.
Click to expand...
Click to collapse
Data pins need shorted together, either in the USB cig plug, or some micro USB cables are this way...
Additionally, the USB cable you use needs to have thick enough power wires to support 1.8A charge draw. Many USB cables use 28 AWG wire for the data conductors, and then you get varying degrees of wire gauge for the power conductors depending on manufacturer. Some people use 28 AWG for both, some use 26, and good cables are made with 24 AWG wire. The thicker wire gauge means less resistance so less power is lost and more can be put into the battery. To pull a proper 1.8A the phone probably should have 22AWG power wire in the USB cable really...
earlthepearl said:
Reading from the AC adapter, this thing can charge at 1.8 amps. I'm doing some research on car chargers that can output 2 amps to the phone via a USB cable, but the trick is getting the phone to pull more than .5 amps from a car accessory outlet. So far I haven't had much luck. There seems to be a lot of info on ipad stuff, but not much in the way of high powered Android devices. So I thought I'd start a thread about compatible car chargers that will allow a full 1.8 amp pull from my car outlet, and see what you guys and gals think and have tried. I've attached a pic of my current setup. It's a Proclip holder on a 2012 Mustang. I've used this same setup for several previous phones (S2 Skyrocket and S3). The holder itself is adjustable to accommodate various phones with cases.
Click to expand...
Click to collapse
Hi, not trying to hijack your thread, but can you tell me which case you are using? I like the fact that it has a large lip around the screen.
Thanks
What model pro clip holder is that? I need to replace the one from my nexus. May hold out for the G2 specific one with the cable built in (like the nexus one I have now), but no telling how long that will be.
mikea3000 said:
Hi, not trying to hijack your thread, but can you tell me which case you are using? I like the fact that it has a large lip around the screen.
Click to expand...
Click to collapse
It's the Body Glove case from the AT&T store. It was the only one they had at the time, and I didn't feel like waiting to order one so I overpaid in exchange for some piece of mind.
stetsonaw said:
What model pro clip holder is that? I need to replace the one from my nexus. May hold out for the G2 specific one with the cable built in (like the nexus one I have now), but no telling how long that will be.
Click to expand...
Click to collapse
It's the holder I ordered for my Skyrocket a few years ago. It's a generic adjustable one that fits a lot of different phones with cases. It has fit my SR, GS3, and now my G2, all with cases.
EniGmA1987 said:
Additionally, the USB cable you use needs to have thick enough power wires to support 1.8A charge draw.
Click to expand...
Click to collapse
I have a custom 5 inch up angle micro USB cable I ordered from www.usbfirewire.com. It is a very thick wire, thicker than the charging cable the G2 came with. The one in my pic is probably not thick enough for a 2 amp charge.
Here is an interesting article I came across about car chargers:
The Best USB Car Charger
EniGmA1987 said:
Additionally, the USB cable you use needs to have thick enough power wires to support 1.8A charge draw. Many USB cables use 28 AWG wire for the data conductors, and then you get varying degrees of wire gauge for the power conductors depending on manufacturer. Some people use 28 AWG for both, some use 26, and good cables are made with 24 AWG wire. The thicker wire gauge means less resistance so less power is lost and more can be put into the battery. To pull a proper 1.8A the phone probably should have 22AWG power wire in the USB cable really...
Click to expand...
Click to collapse
Spot on. FWIW, the LG OEM cable is 20AWG on the power wires. This is the only viable explanation as I can't get the OEM wall charger to work with any cables I have sitting around (24AWG at best).
So would we be better off just using the factory charger with a power inverter or is there an actual car charger that will work?
Provided you short the data pins in whatever car charger you buy (if they arent already) and you get a cable with beefy power conductors then you should be able to draw 1.5-1.8A of power through a car charger. You have to make sure the car charger will do what you want though, many 2A chargers also have 2 ports to plug into. What they don't tell you is that each port is limited to 1A and both together will give 2A draw, but not to charge one device. The car itself also may limit power to the charger as well, I know my car specifically says 1.4A max through the cigarette plug. So it is possible to do, it is all just dependent on so many other things that you have to check off the list.
in_dmand said:
So would we be better off just using the factory charger with a power inverter or is there an actual car charger that will work?
Click to expand...
Click to collapse
That's what I'm trying to figure out. I'm tempted to try that Scosche charger, with my thick USB cable. I installed Currentwidget, so I should be ale to see at what rate I'm charging at if I decide to order it.
in_dmand said:
So would we be better off just using the factory charger with a power inverter or is there an actual car charger that will work?
Click to expand...
Click to collapse
I like the Powergen dual 2.1A USB charger I got off of Amazon. Has served me well. But really, anything 1.8A+ that's quality will do. The trick is going to be the USB cable. Still trying to source one from a reputable site, but you want something with 20AWG for the power. If I find something, I'll post it. Thus far I found two sites, kinda obscure, but not thrilled that the shipping alone costs more than the cables which run $6.
---------- Post added at 08:41 PM ---------- Previous post was at 08:39 PM ----------
EniGmA1987 said:
Provided you short the data pins in whatever car charger you buy (if they arent already) and you get a cable with beefy power conductors then you should be able to draw 1.5-1.8A of power through a car charger. You have to make sure the car charger will do what you want though, many 2A chargers also have 2 ports to plug into. What they don't tell you is that each port is limited to 1A and both together will give 2A draw, but not to charge one device. The car itself also may limit power to the charger as well, I know my car specifically says 1.4A max through the cigarette plug. So it is possible to do, it is all just dependent on so many other things that you have to check off the list.
Click to expand...
Click to collapse
I suspect the phone can detect the charger capacity because my OEM LG cable works on both the Apple and Non-Apple ports on the Powergen charger. Since that's the case, the phone doesn't seem to care if the data pins are shorted or not. And the Powergen is advertised as 4.2A total, so 2.1A per port.
kyler13 said:
I like the Powergen dual 2.1A USB charger I got off of Amazon. Has served me well. But really, anything 1.8A+ that's quality will do. The trick is going to be the USB cable. Still trying to source one from a reputable site, but you want something with 20AWG for the power. If I find something, I'll post it. Thus far I found two sites, kinda obscure, but not thrilled that the shipping alone costs more than the cables which run $6.
Click to expand...
Click to collapse
Something worth considering is looking at charging cables labeled for tablets. They usually charge in this amperage range. I plugged my g2 into my kindle fire HD charger (1.8A) and didn't get any slow charge warnings.
Geekybiker said:
Something worth considering is looking at charging cables labeled for tablets. They usually charge in this amperage range. I plugged my g2 into my kindle fire HD charger (1.8A) and didn't get any slow charge warnings.
Click to expand...
Click to collapse
Doesn't that come with the same Amazon branded usb cable you can get by itself? Take a look on the cable. A lot of times they label the wire gauge.
Sent from my VS980 4G using Tapatalk 4
my amazon branded micro usb cables are 28awg and they still allow quick charge with oem wall charger.
The charging issues associated with this phone has been a huge PITA. I've been carrying my stock cable around just so I can charge my phone!!! Subscribed so I can maybe help out with some info...
bova80 said:
my amazon branded micro usb cables are 28awg and they still allow quick charge with oem wall charger.
Click to expand...
Click to collapse
Are you certain that's not just the data side that is 28awg? Very surprised you can pull 1.8A at 28awg.
Sent from my VS980 4G using Tapatalk 4
kyler13 said:
Doesn't that come with the same Amazon branded usb cable you can get by itself? Take a look on the cable. A lot of times they label the wire gauge.
Sent from my VS980 4G using Tapatalk 4
Click to expand...
Click to collapse
They are unmarked.

My OnePlus One melted!!

I just got a new OnePlus One over the holidays. I've noticed that periodically it was getting very hot when I was charging it, both when using a car and wall charger and multiple different cables. On Saturday night I left it on the charger overnight and in the morning the phone was melted around the charger cable! Check out the pics below.
Only thing worse is that OnePlus says that it's likely because I was using a 3rd party charging cable (from my Samsung Galaxy S3) so they won't provide a refund or replace it. But they will let me pay $350 for a new mother board. So I'm out $400 and a brand new phone.
Normally using a different cable and charger wouldn't have such an effect. I know many friends who use aftermarket cables and chargers built for different phones and their phones are fine so I take that cause with a grain of salt.
Having said that, did you do any modifications to the phone, whether it be software or hardware? When it was getting hot, did you do anything about it?
geokilla said:
Normally using a different cable and charger wouldn't have such an effect. I know many friends who use aftermarket cables and chargers built for different phones and their phones are fine so I take that cause with a grain of salt.
Having said that, did you do any modifications to the phone, whether it be software or hardware? When it was getting hot, did you do anything about it?
Click to expand...
Click to collapse
No, I just got it. Didn't root or anything. When it got hot I rebooted the phone .. what is strange is that it didn't seem to always overheat. But it happened more than once on different chargers and cables.
I've been using a Samsung charger and cable that came from a galaxy s4 on so many different phones and nothing ever happened to them. Even have charged my one plus one with it. It was charging very slowly so I just used the one it came with and it charges at full speed.
Try talking with a different person and not mention using a different cable and charger. Its definitely not because of that. You deserve a new one.
Sent from my A0001
How??
abhishekv09 said:
How??
Click to expand...
Click to collapse
Exactly...
abhishekv09 said:
How??
Click to expand...
Click to collapse
Probably due to using a cable that isn't rated to carry the current that the charger outputs and that the phone draws.
Transmitted via Bacon
timmaaa said:
Probably due to using a cable that isn't rated to carry the current that the charger outputs and that the phone draws.
Transmitted via Bacon
Click to expand...
Click to collapse
kinda like using a skill saw on one of those two dollar 12' household extension cords. everything gets hot.
It's really odd. The One itself uses a pretty powerful 2A charger :/
Sent from my A0001 using XDA Premium 4 mobile app
Hmm... did you charge your phone directly when it was still hot?
timmaaa said:
Probably due to using a cable that isn't rated to carry the current that the charger outputs and that the phone draws.
Transmitted via Bacon
Click to expand...
Click to collapse
Thing is if a charger comes rated at a high output amp, they usually ship an appropriate gauge cable for it. I'm pretty sure Samsung would've shipped a 28/24AWG Micro-USB cable with a 1/1.5/2A (maybe not 1A) charger to prevent the wire from melting out. My guess is OP probably mixed cables with chargers. It's common to have multiple Micro-USB to USB cables these days given most electronics support. Most of the time these cables are 28/28 gauge. I am guessing OP used a 28/28 with a high amp charger (although the standard S3 charger seems to be rated at 1A from my search results). Seems like OP used the OnePlus One charger rated at 2A with a cable which was probably rated for 0.7-1A (that seems to be the standard S3 charger's output).
Can we get more info on what charger and what gauge cable was used OP?
sabrefresco said:
Thing is if a charger comes rated at a high output amp, they usually ship an appropriate gauge cable for it. I'm pretty sure Samsung would've shipped a 28/24AWG Micro-USB cable with a 1/1.5/2A (maybe not 1A) charger to prevent the wire from melting out. My guess is OP probably mixed cables with chargers. It's common to have multiple Micro-USB to USB cables these days given most electronics support. Most of the time these cables are 28/28 gauge. I am guessing OP used a 28/28 with a high amp charger (although the standard S3 charger seems to be rated at 1A from my search results).
Can we get more info on what charger and what gauge cable was used OP?
Click to expand...
Click to collapse
Yeah, that's exactly what I said.
Transmitted via Bacon
timmaaa said:
Yeah, that's exactly what I said.
Transmitted via Bacon
Click to expand...
Click to collapse
I was just trying to bring the odds of this happening to my phone closer to nil with a possible scenario so I could sleep better tonight after leaving it on charge :silly:
Everybody got a phone charger and cable with their phone right? Why would you use some other cable or charger then? Especially now that it seems that its possible to have your phone melt with using 3rd party equipment, why would you still not use the charger/cable that came with the phone? To me thats like buying a truck, putting different wheels on it and getting pissed when something happens.
Red5 said:
Everybody got a phone charger and cable with their phone right? Why would you use some other cable or charger then? Especially now that it seems that its possible to have your phone melt with using 3rd party equipment, why would you still not use the charger/cable that came with the phone? To me thats like buying a truck, putting different wheels on it and getting pissed when something happens.
Click to expand...
Click to collapse
Convenience of not carrying that same cable everywhere? OP seemed to be using chargers at home and in his car, so it's easier to have a cable for each of those chargers.
Maybe the phone is defective. I hate it when OEM'S being cheap.
C'mon One Plus. Don't be like the ****ty samsung. Make the difference
Hey, you can easily and realitively cheaply change the plastic back cover on the OPO. Just purchase an original back cover replacement from OPO. It comes in various colors and even in bamboo. If the metal plug is still ok and only the plastic melted, you should be ok and still have a 100% original phone.
freeewilly said:
Hey, you can easily and realitively cheaply change the plastic back cover on the OPO. Just purchase an original back cover replacement from OPO. It comes in various colors and even in bamboo. If the metal plug is still ok and only the plastic melted, you should be ok and still have a 100% original phone.
Click to expand...
Click to collapse
He needs to change the fried motherboard
sabrefresco said:
I was just trying to bring the odds of this happening to my phone closer to nil with a possible scenario so I could sleep better tonight after leaving it on charge :silly:
Click to expand...
Click to collapse
Leaving it on charge overnight isn't good for the battery anyway, the more time a lithium battery spends at peak voltage (4.2v) the faster it degrades.
Transmitted via Bacon
WHen you don't have the official charger/cable with you, I ALWAYS tell people to charge it via a computer USB port (0.5 A) instead to be on the safe side (with whatever cable you plan to use).
And never mix/match your USB cable/charger ports.

Categories

Resources