As described in Chainfire's goole+ post I tried to reroot my GS4 again after it upgraded to MH5 (DBT version).
And it failed to flash with Odin, this is the log from Odin, the result in Odin is a red square with FAIL as message:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img.ext4
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
The cf autoroot I use is indeed with a timestamp of 05 september.
My phone gives these messages
ODIN MODE
Then a few white text lines:
Product name: GT-I9505
Current binary: Samsung official
System status: official
KNOX Kernel lock: 0x0
KNOX Warranty void: 0x0
CSB-Config-LSB: 0x30
Then a line in grey:
Write protection: enable
then 2 final lines in red:
start: [224,1440]
bar: [240,1440]
On the rest of the screen is still mentions Downloading, do not turn off target!!
Any idea on what is causing this problem ?
gerritcap said:
As described in Chainfire's goole+ post I tried to reroot my GS4 again after it upgraded to MH5 (DBT version).
And it failed to flash with Odin, this is the log from Odin, the result in Odin is a red square with FAIL as message:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-jflte-jfltexx-gti9505.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img.ext4
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
The cf autoroot I use is indeed with a timestamp of 05 september.
My phone gives these messages
ODIN MODE
Then a few white text lines:
Product name: GT-I9505
Current binary: Samsung official
System status: official
KNOX Kernel lock: 0x0
KNOX Warranty void: 0x0
CSB-Config-LSB: 0x30
Then a line in grey:
Write protection: enable
then 2 final lines in red:
start: [224,1440]
bar: [240,1440]
On the rest of the screen is still mentions Downloading, do not turn off target!!
Any idea on what is causing this problem ?
Click to expand...
Click to collapse
make sure you read other posts about rooting as you will void your warranty as Knox void warranty will show 0x1. so if you want to void your device flash at your own risk. hope this helps you out. if id have known i would void my warranty i would not have rooted my device
Related
When i power on my galaxy s4 show this message: "Firmware u pgrade encountered an issue. Please select recovery mode in Kies & try again."
VOLUME UP + HOME + POWER = does not work
VOLUME DOWN + HOME + POWER = download mode works, but when i flash I9505XXUFNA1_I9505OXAFNA1_I9505XXUFNA1_HOME (4.4.2) i get this erro :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNA1_I9505OXAFNA1_I9505XXUFNA1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
In Phone screen:
PRODUCT NAME: GT-I9505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE: enable
START [244,14448]
SW REV. CHECK FAIL : fused : 4 , Binary : 3
someone can help me?
Get it to repair to one service center. Your phone is a paperweight (fused:4)
Odin version
EChacon said:
When i power on my galaxy s4 show this message: "Firmware u pgrade encountered an issue. Please select recovery mode in Kies & try again."
VOLUME UP + HOME + POWER = does not work
VOLUME DOWN + HOME + POWER = download mode works, but when i flash I9505XXUFNA1_I9505OXAFNA1_I9505XXUFNA1_HOME (4.4.2) i get this erro :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNA1_I9505OXAFNA1_I9505XXUFNA1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
In Phone screen:
PRODUCT NAME: GT-I9505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE: enable
START [244,14448]
SW REV. CHECK FAIL : fused : 4 , Binary : 3
someone can help me?
Click to expand...
Click to collapse
what odin version use you?
So, I was trying to flash my custom rom to my SCH-i545 (Verizon S4) and now it's stuck in download mode!
It's an NC5 and android 4.4.2 (I think) . Pretty much every forum i visited said to use TWRP and Safestrap, but after flashing the custom recovery and rebooting, it would not leave download mode. Tried flashing a custom recovery with odin, and it fails.
Phone output:
Could not do normal boot.
PRODUCT NAME: SCH-i545
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB:0x30
WRITE PROTECTION: Enable
eMMC BURST MODE: enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 6, Binary : 1
Odin output:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRUAMDK_NoWipe.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> NON-HLOS.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried the recovery mode combo at least 20 times, to no avail. Any help for this noob?
Nevermind, i'm an idiot. I had the wrong .tar.md5
Unhappy Unable To Root
I've tried the Kingo Root (Stays On An Endless Loop), Towelroot (Phone Not Supported Even When Changing The Other 3 Codes That Can Be Found On Google) And By Odin Watching A Thousand Tutorials And None Work, It's Frustrating And Exhausting, I'm sorry if there's another post for this but i got tired of searching and looking, hopefully someone will understand & try to help.
below is what appears in odin when I try to do it through that method...
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-jfltecan-jfltevl-sghi337m.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
On the phone screen appears:
PRODUCT NAME: SGH-I337
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X0
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: Enable
eMMC BURST MODE: Enable
you can find me on facebook at: facebook.com/PeaceBeyondEternity
if you find/know anything and can help me
skater-boy-zero said:
Unhappy Unable To Root
I've tried the Kingo Root (Stays On An Endless Loop), Towelroot (Phone Not Supported Even When Changing The Other 3 Codes That Can Be Found On Google) And By Odin Watching A Thousand Tutorials And None Work, It's Frustrating And Exhausting, I'm sorry if there's another post for this but i got tired of searching and looking, hopefully someone will understand & try to help.
below is what appears in odin when I try to do it through that method...
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-jfltecan-jfltevl-sghi337m.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
On the phone screen appears:
PRODUCT NAME: SGH-I337
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X0
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: Enable
eMMC BURST MODE: Enable
you can find me on facebook at: facebook.com/PeaceBeyondEternity
if you find/know anything and can help me
Click to expand...
Click to collapse
First off, the Odin method isn't working because CF-Auto-Root is designed for the I337M not the I337. We need more information about your device... head to Settings then About Device. Post the Baseband, the Build Number, Kernel Version,etc. or take a screenshot of it and post it here. Towelroot should work *if* you are on a current version of Android, and if your on MK2 you can use Saferoot.
I am trying to get back to stock firmware after using a custom 5.0.2 ROM. I've tried about everything I could find on forums/website and have come up empty handed. I have tried all the general stuff... USB Cables, USB Ports, Computers, etc. In the process of trying to flash back I tried going back to an older version of android which I guess was a bad idea, because that breaks the sound because of KNOX. ¯\_(ツ)_/¯
When trying to flash MJA with Odin this is what I get.
This is what I get on the phone screen.
ODIN MODE
PRODUCT NAME: SPH-L720
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC BURST MODE: enabled
START [224, 1448]
SW REV. CHECK FAIL : fused : 5, Binary : 4
This is what shows up in Odin's log window.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUEMJA_L720SPTEMJA_L720VPUEMJA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
anyone? :\
Anyone?
http://forum.xda-developers.com/showthread.php?t=3025279
First Of All Sorry, My English Is A Little Bad, I Speak Spanish But I`m Doing The Best That I Can...
I Have An S5 (G900P) And I`m Trying To Install A Stock Rom (OA6) Via Odin But Appears An Error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_SPT_G900PVPU1BOA6_G900PSPT1BOA6_CL3859396_QB3804569_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And On My Cellphone
Odin Mode
Product Name: G900P
Current Binary: Custom
System Status: Custom
Reactivation Lock (KK): Off
Knox Warranty Void: 0x1 (4)
Qualcomm Secureboot: Enable (CSB)
Rp Swrev: s1, T3, R1, A3, P1
Secure Download: Enable
UDC Start
SW REV CHECK FAIL : [aboot]Fused 3 > Binary 1
Does Anyone Knows How Can I Fix This Problem?
What firmware was it on originally?
justinxfan said:
What firmware was it on originally?
Click to expand...
Click to collapse
OK4, but i tried to install it and either i can`t