Related
someone save me please... I've been struggle for two weeks...
I'm using S5-G900F, its a Hongkong version, and I'm currently in UK with giffgaff. last month I tried few new rom and then I can't use voice service any more. However I still have internet. Some detail below:
APN
1. I 100% sure its not an APN problem
IMEI
1. IMEI seems ok, start 4 digit 3524****
SIM card related
1. At first I assume it's a SIM card related problem, I tried 2 SIM with different ISP, neither work.
2. Also, I put those 2 SIM on my iphone4 to verify that the SIM is good, and both card work.
3. I also checked the SIM card cable, I put one piece of paper above the SIM to tight the contact, still doesn't work.
Phone related
1. Before I brought the phone, I had check the bands it supports, and it is capable to used here. And the phone work perfect (well, with stock firmware its really slow) before everything happen.
2. Since I brought this phone in HK and now I'm in UK, I tried to flash both latest UK and HK firmware (lollipop), neither work.
3. I also tried only flash baseband from that two firmware plus one old-version baseband. none work.
4. For those flash mentioned above, I do full wipe.
Rom
The rom I tried list below (in time sequence)
1. XtreStoLite (the BL/baseband is extract from Brazil stock firmware. After that problem occur, but I didn't realize)
2. CM12 (this two are all from this forum)
3. TGY-G900FZHU1BOA1-20150120092320 (HK stock firmware, 5.0. Try to recovery the voice)
4. BTU-G900FXXU1BOB7-20150223084756 (UK stock firmware, 5.0. Still trying)
5. Also 2 baseband/BL from XtreStoLite thread (Another is an old-version. Still).
So now for everyday, I had to carry two phone... one just to make sure I don miss any call.... I have tried and still no clue... really need some help here.... Help please...
Tian02 said:
someone save me please... I've been struggle for two weeks...
I'm using S5-G900F, its a Hongkong version, and I'm currently in UK with giffgaff. last month I tried few new rom and then I can't use voice service any more. However I still have internet. Some detail below:
APN
1. I 100% sure its not an APN problem
IMEI
1. IMEI seems ok, start 4 digit 3524****
SIM card related
1. At first I assume it's a SIM card related problem, I tried 2 SIM with different ISP, neither work.
2. Also, I put those 2 SIM on my iphone4 to verify that the SIM is good, and both card work.
3. I also checked the SIM card cable, I put one piece of paper above the SIM to tight the contact, still doesn't work.
Phone related
1. Before I brought the phone, I had check the bands it supports, and it is capable to used here. And the phone work perfect (well, with stock firmware its really slow) before everything happen.
2. Since I brought this phone in HK and now I'm in UK, I tried to flash both latest UK and HK firmware (lollipop), neither work.
3. I also tried only flash baseband from that two firmware plus one old-version baseband. none work.
4. For those flash mentioned above, I do full wipe.
Rom
The rom I tried list below (in time sequence)
1. XtreStoLite (the BL/baseband is extract from Brazil stock firmware. After that problem occur, but I didn't realize)
2. CM12 (this two are all from this forum)
3. TGY-G900FZHU1BOA1-20150120092320 (HK stock firmware, 5.0. Try to recovery the voice)
4. BTU-G900FXXU1BOB7-20150223084756 (UK stock firmware, 5.0. Still trying)
5. Also 2 baseband/BL from XtreStoLite thread (Another is an old-version. Still).
So now for everyday, I had to carry two phone... one just to make sure I don miss any call.... I have tried and still no clue... really need some help here.... Help please...
Click to expand...
Click to collapse
Can anyone help me please....
Was the phone service working for you before you tried a new ROM?
I have the same issue. Can't make or recieve calls. Internet is working though.
When you try to call someone, do you get 'call ended' message almost immediately after dialing out?
Also, when you go to phone / settings / additional settings (or more settings) - does the 'network or sim card error' pop up?
Can't figure this out... Hopefully someone would be able to point us to right direction, other than to replace it
And of course I did a factory reset, new roms, modems, everything there is to try. nothing helped
could it be because of Region Locking? Maybe it's locked again after flashing?. I want to buy this phone but I am not sure if it will get region locked again after it gets updated or custom flashed.
Kamco said:
Was the phone service working for you before you tried a new ROM?
I have the same issue. Can't make or recieve calls. Internet is working though.
When you try to call someone, do you get 'call ended' message almost immediately after dialing out?
Also, when you go to phone / settings / additional settings (or more settings) - does the 'network or sim card error' pop up?
Can't figure this out... Hopefully someone would be able to point us to right direction, other than to replace it
And of course I did a factory reset, new roms, modems, everything there is to try. nothing helped
Click to expand...
Click to collapse
Yes, before I flash those ROM everything goes well. I'm currently using CM12 so I don't have the setting you mention. But anyway I never seen that pop message before. I guess the SIM card work good as the phone can connect to the internet (not wifi, cellular internet).
Hi Guys,
I am writing this Thread believing that I will get a solution as Yota company has not provided any solution after 15 days trouble shooting. I just brought the phone from Russian seller through eBay.com to India and after 2 months of fight from the local customs office I just got my phone. I was very happy and was floating in air to have the first dual screen phone in my hand. The phone was flawless with dual screen was working awesome. The phone came with lollipop update. I switched on the phone with out inserting the simcard, the phone prompted for a small 350 MB update and I just update the phone. Then I just inserted the Simcard after which i started facing issue. The issue was the phone is able to read and shoe the service provider name but there was no network signal and it was showing only emergency calls. When i tried to make calls it showed network no registered. I tried with different simcard which resulted in the same issue. I though it might be a simcard issue and checked with my old phone but there was no simcard issue. So i just contacted the Yota tech team through mail to help me on this issue. They asked me do some basic troubleshooting but there was no use after 15 days they asked me to ship the phone to nearest service center which is in Russia. The issue is to and back from Russia customs will cost me the price of 2 Yotaphone fist generation phone price. So I through of resolving this issue myself and researched in online. I found that Samsung phones were also facing the same issue after update and tried all the solutions given in internet but there was no use. Finally there was a solution asking to root the phone and install the ariza patch which would solve the issue. I just rooted my phone and when I installed the ariza it showed it was not compilable for yotaphone 2. I just searched in XDA forums and could not find anyone reporting the similar issue with a solution. So I through of creating new thread in hope of getting a solution in this issue. Please help me in this issue by creating a patch or any solution which will me help me out of this. I am not able to use the phone as the basic call function is not even working reset the phone is a heaven.:crying::crying::crying:
bharath9962 said:
Hi Guys,
I am writing this Thread believing that I will get a solution as Yota company has not provided any solution after 15 days trouble shooting. I just brought the phone from Russian seller through eBay.com to India and after 2 months of fight from the local customs office I just got my phone. I was very happy and was floating in air to have the first dual screen phone in my hand. The phone was flawless with dual screen was working awesome. The phone came with lollipop update. I switched on the phone with out inserting the simcard, the phone prompted for a small 350 MB update and I just update the phone. Then I just inserted the Simcard after which i started facing issue. The issue was the phone is able to read and shoe the service provider name but there was no network signal and it was showing only emergency calls. When i tried to make calls it showed network no registered. I tried with different simcard which resulted in the same issue. I though it might be a simcard issue and checked with my old phone but there was no simcard issue. So i just contacted the Yota tech team through mail to help me on this issue. They asked me do some basic troubleshooting but there was no use after 15 days they asked me to ship the phone to nearest service center which is in Russia. The issue is to and back from Russia customs will cost me the price of 2 Yotaphone fist generation phone price. So I through of resolving this issue myself and researched in online. I found that Samsung phones were also facing the same issue after update and tried all the solutions given in internet but there was no use. Finally there was a solution asking to root the phone and install the ariza patch which would solve the issue. I just rooted my phone and when I installed the ariza it showed it was not compilable for yotaphone 2. I just searched in XDA forums and could not find anyone reporting the similar issue with a solution. So I through of creating new thread in hope of getting a solution in this issue. Please help me in this issue by creating a patch or any solution which will me help me out of this. I am not able to use the phone as the basic call function is not even working reset the phone is a heaven.:crying::crying::crying:
Click to expand...
Click to collapse
Do you still have this problem?
I wasn't sure at first, I thought it was my sim card, but I have tried 2 different networks sims and they both get no signal in my Yotaphone 2...
The network's name does appear, so the sim must be being read somewhat, but I always get no signal.
I literally have no idea what to do.
I too turned the phone on without a simcard, flashed the RU latest rom, flashed TWRP, rooted it etc, surely that has nothing to do with it...?
@bharath9962 ! I fixed it!
I have no idea why this happened, and I spent a few hours trying to fix it, very angry. I downgraded to 4.4 to see if it would help, put back the native China rom that came with my phone (accidentally deleted my backup too...)
I bought a new sim card just for this phone because the old one did not 'work'.
This is not a popular phone so it's hard to find information, anyway... I'm very relieved now. I can only imagine you gave up...
I found the answer here - thewichitacomputerguy.com/blog/how-i-fixed-your-sim-card-does-not-allow-connection-network-g1
1. Open the phone dialer
2. Enter: *#*#4636#*#* (Once entered, you will be taken directly to a "Testing" page) [4636 spells INFO]
3. Tap Phone Information
4. Scroll to the bottom of the screen and you should see a button that says radio off. Hit this button and when it reads radio on Hit it again to turn the radio back on. <-- (Not a Typo)
I rebooted and waited a few seconds, no signal. I turned on airplane mode, turned it off, and it worked!
Now I can go back to RU 1.99 and reinstall all my stuff...
cbcbcvcc said:
@bharath9962 ! I fixed it!
I have no idea why this happened, and I spent a few hours trying to fix it, very angry. I downgraded to 4.4 to see if it would help, put back the native China rom that came with my phone (accidentally deleted my backup too...)
I bought a new sim card just for this phone because the old one did not 'work'.
This is not a popular phone so it's hard to find information, anyway... I'm very relieved now. I can only imagine you gave up...
I found the answer here - thewichitacomputerguy.com/blog/how-i-fixed-your-sim-card-does-not-allow-connection-network-g1
1. Open the phone dialer
2. Enter: *#*#4636#*#* (Once entered, you will be taken directly to a "Testing" page) [4636 spells INFO]
3. Tap Phone Information
4. Scroll to the bottom of the screen and you should see a button that says radio off. Hit this button and when it reads radio on Hit it again to turn the radio back on. <-- (Not a Typo)
I rebooted and waited a few seconds, no signal. I turned on airplane mode, turned it off, and it worked!
Now I can go back to RU 1.99 and reinstall all my stuff...
Click to expand...
Click to collapse
@cbcbcvcc may i know which country you are and what type of sim your using. So that i could check my issue accordingly.. And thanks for your reply tp my post as i waa waiting for some one to help for the last 3 months... When hope was vanishing you just showed up.. This help means a lot to me
bharath9962 said:
@cbcbcvcc may i know which country you are and what type of sim your using. So that i could check my issue accordingly.. And thanks for your reply tp my post as i waa waiting for some one to help for the last 3 months... When hope was vanishing you just showed up.. This help means a lot to me
Click to expand...
Click to collapse
My country is in Asia but I believe this does not matter - the problem was that somehow the radio (cell phone function) was 'off'/glitched, and had to be turned on+off to make the phone function again. Using a different country's sim card would not fix this problem.
As I wrote above, we both share the fact that we first turned our phones on with no sim, and updated. Maybe just a coincidence...
Just try the guide and please let me know if it is fixed!
cbcbcvcc said:
My country is in Asia but I believe this does not matter - the problem was that somehow the radio (cell phone function) was 'off'/glitched, and had to be turned on+off to make the phone function again. Using a different country's sim card would not fix this problem.
As I wrote above, we both share the fact that we first turned our phones on with no sim, and updated. Maybe just a coincidence...
Just try the guide and please let me know if it is fixed!
Click to expand...
Click to collapse
Hi cbcbcvcc,
Tried the guide but still no use, I also downgraded the ROM and tried the guide still no use. This is hurting me so bad.. Do you have any other way to resolve the issue please share with me.
No SIM CARD
Hi to All,
suddenly after I did a reset and change the sim card, the Yotaphone is no more recognize the sim card.
I try to install a new rom...nothing
I try to install the Kitkat rom...nothing
I try the method suggested here to use the code *#*#46..... nothing
any help please
Please I have tried the guidelines but the radio refuse to ON. I click on it but not never respond
Hello, I have update my Yotaphone and now I receive WCDMA, but no gsm/edge signal .
I change the Rom (lollipop,kitkat,, HK rom, EU Rom)but I have always the problem :
I receive H, H+. But no Edge/GSM...
Can you help me.
[SOLVED]
Fix for Yotaphone 2 YD206 from China
If you already flashed the phone to latest EU 5.0, you can skip 1-5
1. download via FTP: fw.ydevices.com/YotaPhone2/YotaPhoneFlasher/yotaphone2_flasher.exe and install
2. run flasher and download latest EU rom (2 - 5- 7)
3. turn off the phone and turn it on while holding volume down - this will boot the phone in "downloading..." mode
4. in the flasher press 1 (Flash the cellphone)
5. the phone is now on 5.0.0-EU1.1.124b and 2G is not working at all and 3G is connecting only to 2100 MHz (on my cell network)
6. download via FTP: fw.ydevices.com/YotaPhone2/Firmwares/CN/4.4.3-S01-003-CN1.0.3.32a.zip
7. unzip the file and copy \radio to c:\program files (x86)\yotaphone_flasher
8. run cmd and go to c:\program files (x86)\yotaphone_flasher
9. repeat step 3.
10. run next lines:
fastboot flash modem radio\NON-HLOS.bin
fastboot flash sbl1 radio\sbl1.mbn
fastboot flash rpm radio\rpm.mbn
fastboot flash tz radio\tz.mbn
11. reboot the phone and enjoy 2G and strong 3G signal
manu3556 said:
Hello, I have update my Yotaphone and now I receive WCDMA, but no gsm/edge signal .
I change the Rom (lollipop,kitkat,, HK rom, EU Rom)but I have always the problem :
I receive H, H+. But no Edge/GSM...
Can you help me.
Click to expand...
Click to collapse
good job deepmnd
thanks :good::good::good:
deepmnd said:
Fix for Yotaphone 2 YD206 from China
If you already flashed the phone to latest EU 5.0, you can skip 1-5
1. download via FTP: fw.ydevices.com/YotaPhone2/YotaPhoneFlasher/yotaphone2_flasher.exe and install
2. run flasher and download latest EU rom (2 - 5- 7)
3. turn off the phone and turn it on while holding volume down - this will boot the phone in "downloading..." mode
4. in the flasher press 1 (Flash the cellphone)
5. the phone is now on 5.0.0-EU1.1.124b and 2G is not working at all and 3G is connecting only to 2100 MHz (on my cell network)
6. download via FTP: fw.ydevices.com/YotaPhone2/Firmwares/CN/4.4.3-S01-003-CN1.0.3.32a.zip
7. unzip the file and copy \radio to c:\program files (x86)\yotaphone_flasher
8. run cmd and go to c:\program files (x86)\yotaphone_flasher
9. repeat step 3.
10. run next lines:
fastboot flash modem radio\NON-HLOS.bin
fastboot flash sbl1 radio\sbl1.mbn
fastboot flash rpm radio\rpm.mbn
fastboot flash tz radio\tz.mbn
11. reboot the phone and enjoy 2G and strong 3G signal
Click to expand...
Click to collapse
Hello!
I try to figure out what you did but I get stucked in number 10.
Actually I flashed my Yotaphone with the chinese radio the first time, but I don't get good connectivity.
Anyways I try to do what you wrote, but when I tipe the first line (first fastboot command), cmd keep saying waiting for the device... maybe is that I'm impatient but nothing happens.
I try other USB ports and nothing works...
So actually I don't know if I'm doing it right or if I have to wait for a longer period of time (10 minutes or more).
Any help would much appreciated.
Cheers!
Hi there,
you don't have ADB drivers installed. Google for "universal adb driver" and install. There is driver included with yota 5.0 firmware (C:\Program Files (x86)\yotaphone_flasher\Driver\Google), but any other adb driver should work as well.
And use original yota usb cable!!!
It shouldn't take more that a few seconds for those commands to execute.
MDans said:
Hello!
I try to figure out what you did but I get stucked in number 10.
Actually I flashed my Yotaphone with the chinese radio the first time, but I don't get good connectivity.
Anyways I try to do what you wrote, but when I tipe the first line (first fastboot command), cmd keep saying waiting for the device... maybe is that I'm impatient but nothing happens.
I try other USB ports and nothing works...
So actually I don't know if I'm doing it right or if I have to wait for a longer period of time (10 minutes or more).
Any help would much appreciated.
Cheers!
Click to expand...
Click to collapse
Had the same problem
Hi all, I had the same problem when I flashed russian firmware (YD201) over my phone which originally had honkong firmware (YD206).
I can inform that for me it also worked to flash the Chinese firware with yotaflasher.
However, when I tried to only flash the radio, it seemed it did not work. So I flashed the complete chinese kitkat firmware with yotaflasher and then afterward just removed/renamed the radio folder when flashing the newest russian lollipop firmware. Everything working great now, even was able to do some ota's without any problems since the ota's did not update anything of the radio img's.
And indeed you first need to make sure that you have the fastboot drivers installed and your device gets recognized as fastboot device by your PC.
You can test this by doing "fastboot devices". If you device turns up there as a fastboot devices, then the drivers and connection from pc to phone are ok.
Good Luck!
Thank you deepmnd and tomgaga.
Actually I had to activate developer options... And then reinstall the ADB cause, aparently I had it but it didn't work.
After that the instructions worked perfectly, but I still have network issues.
I don't know if it is because I have a MVNO (Mobile virtual network operator) and the phone has to change between the networks ( the one that provides the network and the MVNO).
I think that when it changes from one net to the other is when I lose connectivity and sometimes I have to search the network and choose it manually.
So this problem actually happened to me and the solution was to activate Roaming services (but I dont' know if is actually the same problem).
Anyways I can see that I connect to EDGE, HSPA/HSDPA and LTE.
For sure there is a way to monitor the network and check wich ones works.
Another guess is that being a phone for the chinese market, and the lack of the 900mhz band is causing this ¿?
So at the moment I'm losing signal just by walking on the street and I live in a big city. It seems that LTE and H works fine but I don't have a a way to assure this.
When I will have a spare time I will try to reflash the phone with the instructions deepmnd provided and see if it will work.
Thank you for your help!
Any advice will be appreciated!!
Update:
I try tomgaga approach I will test it just to see if is the network or my provider
Does anybody know which bands different firmwares support?
Reception is incredibly bad in my case (206 flashed with EU firmware).
It'd be nice if somebody has any info on unlocking different bands for yotaphone2.
kbal said:
Does anybody know which bands different firmwares support?
Reception is incredibly bad in my case (206 flashed with EU firmware).
It'd be nice if somebody has any info on unlocking different bands for yotaphone2.
Click to expand...
Click to collapse
Here you have the bands
https://www.frequencycheck.com/compare-devices/qkjseR/yota-yotaphone-2-yd201/yota-yotaphone-2-yd206
I have the same problem as you, I will try this weekend to downgrade to the older chinese rom and check if the reception get better.
And if then to the latest RU rom.
MDans said:
Here you have the bands
https://www.frequencycheck.com/compare-devices/qkjseR/yota-yotaphone-2-yd201/yota-yotaphone-2-yd206
I have the same problem as you, I will try this weekend to downgrade to the older chinese rom and check if the reception get better.
And if then to the latest RU rom.
Click to expand...
Click to collapse
Thanks for that, it helps a lot to clear the situation regarding the two models.
Now, taking in account deepmnd´s solution above, would it be possible to find those missing bands from the original 206 which are not available to the updated (and then international, 201-) version and add them individually, file by file via the fastboot flashing?
I followed deepmnd's instructions, and my phone now connects to GSM/EDGE, which was not possible before using the EU Radio (latest EU rom). Thanks for this!
Unfortunately it now preferably (!) connects to EDGE, although the LTE/WCDMA-Option is prioritized. I can force the phone to connect to WCDMA by using the WCDMA-only-option, but in this case it does not commit a fallback to EDGE if 3G is missing and I have no connectivity at all, unless I change the band-options and force a connect to EDGE. I'd like it to switch between the bands automatically, as my YD201 did without problems (in Germany).
Any hints to solve this problem?
Thanks in advance, Knut
deepmnd said:
Fix for Yotaphone 2 YD206 from China
If you already flashed the phone to latest EU 5.0, you can skip 1-5
1. download via FTP: fw.ydevices.com/YotaPhone2/YotaPhoneFlasher/yotaphone2_flasher.exe and install
2. run flasher and download latest EU rom (2 - 5- 7)
3. turn off the phone and turn it on while holding volume down - this will boot the phone in "downloading..." mode
4. in the flasher press 1 (Flash the cellphone)
5. the phone is now on 5.0.0-EU1.1.124b and 2G is not working at all and 3G is connecting only to 2100 MHz (on my cell network)
6. download via FTP: fw.ydevices.com/YotaPhone2/Firmwares/CN/4.4.3-S01-003-CN1.0.3.32a.zip
7. unzip the file and copy \radio to c:\program files (x86)\yotaphone_flasher
8. run cmd and go to c:\program files (x86)\yotaphone_flasher
9. repeat step 3.
10. run next lines:
fastboot flash modem radio\NON-HLOS.bin
fastboot flash sbl1 radio\sbl1.mbn
fastboot flash rpm radio\rpm.mbn
fastboot flash tz radio\tz.mbn
11. reboot the phone and enjoy 2G and strong 3G signal
Click to expand...
Click to collapse
Thank you! I had missed calls and did not know what caused them. Then I noticed this happened when I was not on LTE network but on WCDMA or 2G network. And this seems to have solved the issue for me as well.
OK, *FIRST TIME POSTER HERE* so please excuse any unintentional ignorance of rules or etiquette.
I'm just super excited to get this phone working the way I like it, and it's all thanks to xda so I was moved to create an account to express my thanks AND hopefully help a few people back.
How? Well after reading through pretty much everything I could find on the N910S here and elsewhere, it seems that no-one (yet?) has been able to confirm a working mod that meets the following:
1. N910S Exynos Korean version
2. Some kind of custom English only ROM that removes the Korean characters from keypad and other network-apps
3. Removed bloatware
4. Easy-to-follow, how-to guide
Seems there were quite a few ppl who wanted the same thing so I just want to let you know what I did to get it working.
*PLEASE NOTE* Everything contained in this summary was found through over a week of tedious reading, research, trial & error. BUT in the end all the necessary information was contained, or linked to, in xda forums. It's just that all the relevant information and files were scattered over many different threads and topics. I'm just collating it all here to hopefully make it easier for the next person to find.
Background info: I'm technically competent but relatively new to phone modding - I've only rooted my HTC E8 before this to remove bloatware. This is my second project. I live in HK and started with a completely stock OEM Note4 N910SKSU2DPK2 after a factory reset. I then did the steps below in order (not including many failed attempts and re-starts, of course) These are just the broadstrokes of what I did, if you need to know how to do each step in detail then please search the forum. It's quite clear and there's no need for me to repeat it here anyway
As it's my first post and I'm in a rush to leave the house soon, I have not bothered with screenshots or links - I'm happy to provide if someone can tell me if the preferred method is link to the thread where the info was found, or you just want a link to the files I used. Again, they were all found through links in threads on xda anyway but I'll have to spend some time to find them again as I didn't bookmark them. Also, if you want the files someone will have to tell me how to upload them here. The filenames/packages are given in [brackets] so maybe you can just search for them?
0. Reminder to backup your phone and data first!
1. Root - was really easy using CF AutoRoot [CF-Auto-Root-trelteskt-trelteskt-smn910s] Just download to your PC and package includes Odin, which for first-timers is the official Samsung software used to flash to your phone.
2. Download:
- ClockWorkMod [n910s-cwm-recovery-6.0.5.1(1113).tar]
- SuperSU [SuperSU-v2.79-201612051815.zip]
- C Mod ROM [C_ROM_N910s.v2HNY.zip] (the site is Korean-based but google translate of the page was enough for a non-Korean like myself)
- N910S DPK2 modem file [N910S-20170114T050808Z.zip] The original thread had links to every modem variant they knew of, so should work with other S/L/K variants BUT of course I haven't tried them.
3. Copy files for SuperSU, CMod ROM, and DPK2 modem onto an external SD card and insert into your phone.
4. Put your phone into Download Mode (from power-off state, hold Vol Down + Home + Power)
5. Run Odin on your PC, connect phone. On Odin, click <AP> and select CWM file. Do not check or modify any other options. Click <Start> to flash CWM recovery to your phone.
6. Once it's done, disconnect from PC, and restart your phone into the new custom recovery mode (from power-off state, hold Vol Up + Home + Power)
7. Choose Install from zip and select the SuperSU file from your ext SD card. (I think this step may not be strictly necessary as it's part of CF AutoRoot, but SuperSU is always handy to have anyway)
8. Reboot into Recovery mode again (available in Advanced menu)
9. Install zip - now choose the CMod ROM file. Reboot into system and have a look around the new UI. It was at this stage that I noticed two things: my HK carrier SIM was not recognised, and as the ROM boasts some Note 5 features the Always On Display function would cause my Note 4 to not be able to wake up once the screen was turned off (manually or via time-out). I had to pull out the battery, restart phone, go straight into Settings -> Display and turn off the Always On Display functionality.
10. To fix the SIM card not recognised, reboot into Recovery Mode again and Install zip - choose the DPK2 modem file (or whichever version your phone's modem is). Restart phone, wait a few minutes and SIM should now work.
*ONE REMAINING ISSUE* Even tho my SIM is 4G/LTE, it seems to be connecting at HSUPA only. Could be reception, I'll check later. But I believe there's a way to select different LTE bands through secret codes or menu, not sure but I'll try that as well later and update if it works.
That's it - hope it helps! Thanks for reading, and don't forget I'm new to this AND a first time poster so be kind in comments/questions please
Update and question
Kookinen said:
*ONE REMAINING ISSUE* Even tho my SIM is 4G/LTE, it seems to be connecting at HSUPA only. Could be reception, I'll check later. But I believe there's a way to select different LTE bands through secret codes or menu, not sure but I'll try that as well later and update if it works.
Click to expand...
Click to collapse
So by following steps in this thread https://forum.xda-developers.com/note-4/help/note-4-sm-n910s-sk-telecom-issues-t2929571/page2 for SKT, I was able to change to LTE Band 3 or 7 (which is what my sim provider offers) and get an LTE signal for data, BUT then I lose voice call functionality. If I choose Band 3 Preferred, it says band changed success, but just connects via HSUPA and I get voice, but no LTE (just like before, or if I choose Automatic)
Can anyone please help me figure this out? How can I get voice AND LTE? Many thanks in advance!
PS - also after I reflashed my modem.bin the baseband changed from N910SKSU2DPK2 to N910SKSU0DPK2. I don't know what this means nor if it has anything to do with the problem I've described above? Can anyone help to explain? Thanks...
Kookinen said:
So by following steps in this thread https://forum.xda-developers.com/note-4/help/note-4-sm-n910s-sk-telecom-issues-t2929571/page2 for SKT, I was able to change to LTE Band 3 or 7 (which is what my sim provider offers) and get an LTE signal for data, BUT then I lose voice call functionality. If I choose Band 3 Preferred, it says band changed success, but just connects via HSUPA and I get voice, but no LTE (just like before, or if I choose Automatic)
Can anyone please help me figure this out? How can I get voice AND LTE? Many thanks in advance!
PS - also after I reflashed my modem.bin the baseband changed from N910SKSU2DPK2 to N910SKSU0DPK2. I don't know what this means nor if it has anything to do with the problem I've described above? Can anyone help to explain? Thanks...
Click to expand...
Click to collapse
Band 3 and 7 are supposed to stick with default settings. I tried it once during my trip to Malaysia and it worked flawlessly. Any chance you might want to contact your carrier?
The trick to switch from 4G-3G-4G works. ATT band 5 preferred
Kookinen said:
*ONE REMAINING ISSUE* Even tho my SIM is 4G/LTE, it seems to be connecting at HSUPA only. Could be reception, I'll check later. But I believe there's a way to select different LTE bands through secret codes or menu, not sure but I'll try that as well later and update if it works.
Click to expand...
Click to collapse
Have you tried switching to 3g only, then switching it back to 4g when available in your phone setting??
I had similar issue with 4g and apparently, this strangely simple trick solved my problem.
Anyway, I tried to download the ROM from the Achonapp but took me ages and I couldn't flash it either. May I know where you got the ROM from?
nosediger said:
Have you tried switching to 3g only, then switching it back to 4g when available in your phone setting??
I had similar issue with 4g and apparently, this strangely simple trick solved my problem.
Anyway, I tried to download the ROM from the Achonapp but took me ages and I couldn't flash it either. May I know where you got the ROM from?
Click to expand...
Click to collapse
Tried your suggestion but now it shows No Service
*update* actually I think your "trick" works... After switching to 3G only, it wouldn't switch back to 4G and showed No Service. I rebooted the phone with a different sim and after a few minutes, it automatically connected to 4G AND I now have voice as well! So, all is working properly now and I'm a happy camper. Reboot with the original sim and still works and connects to 4G. So I think you're right it just needed to be "forced" to select 4G preferred. Thanks for the tip!
Yeah I got it from achonapp as well and it took a while - I think I left it going overnight. But the ROM did work for me. If anyone wants the file direct I'm happy to put it up on my google drive if it's not against forum rules etc.
But since then I've switched to miui8 which is also working pretty much flawlessly as daily ROM, but I haven't tested every single little feature of course. If you wanna try it - https://forum.xda-developers.com/showpost.php?p=70596588&postcount=797
Hey guys, i was wondering if i can flash firmware from other carrier without bricking?
I bought my phone last year locked to carrier, and I unlocked it using doctorSIM service. Phone itself works fine, and as I'm not living in country that i bought my phone from originally, phone gives a message "No SIM card installed" sometimes once a week, sometimes several times a day and i need to remove SIM card or to restart phone to make SIM card work again.
Please note:
- SIM Card from my original carrier (from one that I bought my phone from) works PERFECTLY fine
- My other SIM card (that my phone constantly rejects) works in other phones just fine
- I have tried to reset the phone, and carrier bloatware constantly keeps installing
- EDIT: Wi-Fi and 4G are working PERFECTLY fine
What to do? Any ideas?
Thanks in advance and sorry for gramar mistakes
Bump, flashed other carrier firmware, still same problem.
R u rooted? Have you considered flashing a CSC packet for your location?
I have a 930S, and works fine with the Korean ROM/Chinese language here in the US, on ATT service.
I have flashed the ATT, XAA and TMB CSC sets, and though the phone worked, and loaded the correct USA carrier info, I lost the phone code ability, which I could not solve.
In the end I went back to the original Korean ROM and it's CSC packet. Interestingly, though it works perfectly here in the U.S., and I can use/input phone codes, it still shows Chinese cities for my 'Region", none of which I have selected. When I do a search for local towers, it locates and correctly identifies AT&T, T-Mobile, etc. I select ATT. The Chinese cities remain in the region selection, none selected.
Wait and see if someone knows if CSC (Exynos or US based CPU) are interchangeable. I used CSC packets from a universal ROM setup (non-USA).
JeffDC said:
R u rooted? Have you considered flashing a CSC packet for your location?
I have a 930S, and works fine with the Korean ROM/Chinese language here in the US, on ATT service.
I have flashed the ATT, XAA and TMB CSC sets, and though the phone worked, and loaded the correct USA carrier info, I lost the phone code ability, which I could not solve.
In the end I went back to the original Korean ROM and it's CSC packet. Interestingly, though it works perfectly here in the U.S., and I can use/input phone codes, it still shows Chinese cities for my 'Region", none of which I have selected. When I do a search for local towers, it locates and correctly identifies AT&T, T-Mobile, etc. I select ATT. The Chinese cities remain in the region selection, none selected.
Wait and see if someone knows if CSC (Exynos or US based CPU) are interchangeable. I used CSC packets from a universal ROM setup (non-USA).
Click to expand...
Click to collapse
I'm not rooted, as I use Samsung Pay and have more than one year of warranty left. I will try flashing CSC of the current country I'm in (Austria). Thanks for taking time and writing all this, this problem is unbearable
Hello!
My s7 edge is in trouble, it freezes sometimes, and sometimes it gets a full screen of pixel color flaws, with that problem my root smartphone works two weeks. Sometimes this error occurs in the ROM installation process, I insist on the installation until I can. I tried to install superman rom and due to this problem, the smartphone in the screen of death "exception of bootloader" (But it's already been resolved)...
When searching the internet, I saw that this could have a problem in flash memory.
After all history, I ask;
I could use a twrp file system repair function to try to solve this problem? And how to proceed?
(sorry for the use of google translate)
sekrilhus said:
Hello!
My s7 edge is in trouble, it freezes sometimes, and sometimes it gets a full screen of pixel color flaws, with that problem my root smartphone works two weeks. Sometimes this error occurs in the ROM installation process, I insist on the installation until I can. I tried to install superman rom and due to this problem, the smartphone in the screen of death "exception of bootloader" (But it's already been resolved)...
When searching the internet, I saw that this could have a problem in flash memory.
After all history, I ask;
I could use a twrp file system repair function to try to solve this problem? And how to proceed?
(sorry for the use of google translate)
Click to expand...
Click to collapse
I am, by far, not educated up on TWRP, so I'm not sure what you mean by "repair", other than making sure your data partition is formatted so it does not cause the issues you are talking about.
Here is an interesting read:
https://forum.xda-developers.com/go...o-repairing-corrupted-data-partition-t2577447
Hey guys, update on the problem, i replaced sim card and it works just fine, i will post updates as time goes on
Thanks for the help!
Hey there!
I try to keep it short. I have no network service (the sim is working in other phones). There is sometimes a "stop" like symbol in the top bar or an exclamation mark saying "no chosen network available". However, emergency calls should be possible (phone got network access).
I bought the phone, so it's used and that "problem" was known. I thought I could fix it. I tried the following:
Rooting and RegionLockAway.
Flashing new Firmware (I9505XXUHOA7)
Flashing the ME2 modem and trying to SIM-Unlock it. However I get an popup "error" after pressing NV-Rebuild (it stated Golden Backup exists) and then the phone immediately reboots.
SIM detection seems to work (asks for PIN and notifies on empty sim)
The IMEI is there.
If I try to choose networks it gets a list with EPlus, T-Mobile and Vodafone (I am currently in Germany). Unfortunately I do not know where the phone's from.
Also, I never experienced any popups asking for unlock codes or similar - it is just not able to register on the network.
How can I make sure theres no SIM Lock?
How can I make sure theres no Netlock?
After those two are clear what else could be done? What about NVData?
Anyone any ideas? Thanks!
I can post some infos from the service/UMTS menu, however I am not sure which. I also searched and tried hours but without success.
Replace the SIM card tray. From appearances yours is dying.
Thanks for the reply. Can I test this somehow? I am just wondering since it asks for SIM-PIN and even reads APN data etc. I just searched and it is about 10 bucks on ebay and I should be able to do it at home that would be cool. So since it is detecting my SIM can I test somehow whether there could be other problems causing this problem bevore I try to replace that sim-slot?
Thank you!
By the way: Yesterday I also tried to repair NVData with the SamsungUnlock software as posted somewhere here. While that worked without a problem it did not change anything.
To sim unlock the phone, you could try flashing the 4.2.2 modem, rooting, and using regionlockaway.
fassal said:
Can I test this somehow?
Click to expand...
Click to collapse
I wish there was a way to test it. I only knew mine was bad by sheer luck. Mine revealed itself only after flashing an Android 4.2.2 stock ROM; more current versions didn't show anything.
Could there be a loose connection inside the phone?
Where it is a known issue, there is a possibility that the original owner replaced the SIM tray. When they did, they likely forgot to reuse the foam pad from the top of the connector on the old tray. If that pad is missing the connector will pop up in time.
hey thanks for your help!
I will open the phone and check the connector of the SIM-Tray. But as I already described, it even asks me for the SIM-Pin, but maybe even though something might not be right.
Regarding flashing an 4.4.2 Modem: Is that the "9505_DXUAME2_MODEM.rar"? If, I tried that already (installed that modem, rooted, RegionLockAway and even with the Serive Menu SHA256 OFF method (this one did not work since I got an Error and the phone did not freeze etc.). However, I did not install a full 4.4.2. Stock Rom yet.
Well maybe I could buy a SIM Tray and just connect the PIN without acutally gluing it on the phone. This way I might be able to get a refund if this does not do the trick.
If all these fail I just have to find some new use for that phone
You cannot use an Android 4.4.2 modem or ROM to unlock. The modem or ROM MUST be from Android 4.2.2 or RegionLock Away will not work.
Regarding the SIM tray, foam mounting tape from the local store on top of the connector will work. No need of glue.