[Q] Please Help!!!Good signal connected to HSPAP but no Data - AT&T Samsung Galaxy S 4 Q&A, Help & Troubleshootin

Hello, thank you in advance for whatever help you can give me. I purchased the AT&T galaxy s4 and I am trying to use it in Colombia with my provider Tigo which runs on 1900mhz but I have problems connecting to the internet.
This is my second galaxy s4, the first one I had I opened the AWS bands, selected WCDMA/GSM Mode Only on the service menu and my internet was working just fine. Unfortunately I lost my first phone and bought another one, and went through the same procedures but my mobile data is not working for the most part while it is connected to HSPAP.
If I select GSM only on the srvice menu then it navigates, but at 2G speeds. What seems strange is that I am getting great signal and when I go to about device/status, it shows it is connected to hspap, and gprs, but I dont have an internet connection except at a couple of places, for some reason when I am in my house it works (wifi off), but when I leave my house it doesnt work.
If you have had a similar problem an were able to figure it out I will appreciate any thoughts you may have. It is frustrating having this phone and not being able to use the internet.
Thank you.

Related

[Help!!]I can't hook up to HSDPA with my Kaiser anymore....

Hey guys, My device is Kaiser(TyTNII) and AT&T is my operator.
I live in Philadelphia, US.
Before yesterday my TyTNII can access HSDPA (with "H" symbol on the top right) when I try to use internet.
However, I use Kaiser Tweak to change some setting of my device and suddenly my kaiser doesn't recognize HSDPA network anymore, I mean it will only show "3G" on the top right. I have checked all the settings and everything seems fine.
HSDPA function is checked and same as in the Kaiser Tweak.
Can someone help me out here?
Thanks.
i have the same problem, cant go into hsdpa or even 3g only edge. and it seems to have happened after using kaiser tweak also.
Got some help over in the Kaiser forum that helped me. Go to your comm manager then settings/phone/ then go to band and switch your network type to wcdma. after it updated the network i switched back to auto and it seems to be working so far for me. hope this helps you out, something you could try.
I seem to have the same issue but the above solution doesn't help. Whenever I set the phone to do HSDPA through Connections I loss all data connectivity, once I turn it off HSDPA I get 3G.
Is it possible for radio settings to survive a hard rest / ROM upgrade or is the HSDPA side of my Tilt broken :-(
Any insight or help would be real appreciated.
Several times I have gotten "Warning: Unable to change GSM/UMTS Band, Please try again later."
JohnnyGTO said:
I seem to have the same issue but the above solution doesn't help. Whenever I set the phone to do HSDPA through Connections I loss all data connectivity, once I turn it off HSDPA I get 3G.
Is it possible for radio settings to survive a hard rest / ROM upgrade or is the HSDPA side of my Tilt broken :-(
Any insight or help would be real appreciated.
Several times I have gotten "Warning: Unable to change GSM/UMTS Band, Please try again later."
Click to expand...
Click to collapse
OK is it possible for this to be tower related? What I mean is I drove about 4 miles from my house, got a better signal and surfed the internet using HSDPA. Now I'm back home and HSDPA is chocking and giving me "unknown error 0x80072f78"
What He!!?
One note on my HSDPA trouble, it must some how be related to the one tower nearest my home. When I go anywhere outside a 5 miles radius (I live near the tower) everything works fine.
Here is the weird part, every where else the phone will switch from HSDPA to 3G to Edge and back no problem. Here in town it locks into HSDPA and refuses to switch to 3G or anything else. I don't know if it means anything but it seems to get an IP address I can ping but I don't get any DNS info!.
Now how can I convince AT&T that there's a problem when their support person denies there is any HSDPA services and I should only expect 3G?

3G on and Off

So, i have bugged folks on this forum about getting 3G to work on other carriers, and it turns out - it does work! At first i found out my settings were set to GSM only, but now i also found this weird inconsistency possibly a bug.
If i have Data Off after using 3G or GPRS for some time, when i turn it back on, phone would not connect to data service. After enabling it will simply time out.
I found that if i switch from GSM to WCDMA, and than back, 3G network would connect and work.
I don't know if it's specifically my phone, or a bug, so i'm just throwing it out there.
dialbat said:
So, i have bugged folks on this forum about getting 3G to work on other carriers, and it turns out - it does work! At first i found out my settings were set to GSM only, but now i also found this weird inconsistency possibly a bug.
If i have Data Off after using 3G or GPRS for some time, when i turn it back on, phone would not connect to data service. After enabling it will simply time out.
I found that if i switch from GSM to WCDMA, and than back, 3G network would connect and work.
I don't know if it's specifically my phone, or a bug, so i'm just throwing it out there.
Click to expand...
Click to collapse
What carrier are you getting 3G to work? I doubt its working if its anything that doesn't run on tmobiles bands..the icon will come up and stuff but your either getting edge speeds or not getting any connection. I've had this phone show me 3G with full bars and just time out.. I can eveven put in a sim with a sidekick plan or other data plan and it shows 3G but it does not work
Well, i'm overseas and i have used it on Russian carrier Beeline and carriers in two other countries. Now, i do set my connection to WCDMA only, which gives me 3G icon. When i set it to GSM only, i see GPRS icon show up.
So, it does work, i use fring, online radio, google maps. But as far as speed concerned, i have not tested it.
Just ran a speed test using Speedtest.net tool, I get 3951kbps download, and 655 upload
thats 3G

serious issue on SGS-2 and 3g internet

i own a samsung galaxy s2 ordered from uk,
everything working fine except for this serious issue that i have been trying to resolve till now.
i have a monthly internet subscription from my carrier and it always been working fine on my iphone ( i mean here connecting through the 3g network ). but in the S2 .. i have to use Edge to be able to access the internet ( the mobile network mode must be set to GSM only ). whenever i switch the network mode to GSM\WCDMA auto , the 3g icon appears but when it tries to connect to internet, the phone automatically switch to Flight mode and i loose the network signal. and this happens all the time. till now i am only able to connect to the internet by switching the mobile network mode to GSM only which only uses Edge network .
i have tried every possible thing to resolve this issue but nothing worked for me. please help
What country are you in? What carrier are you on? What bands do they use?
location location location.
Where are you from?
And what frequency does operators in your region operate.
just curious, have you tried hard/factory reset?
i am from saudi arabia and i am using Mobily network.
mobily is using HSDPA network as well as Edge network.
i did a software reset and still the same issue.
phone information:
Baseband version I9100XXKDH
Kernel version 2.6.35.7--I9100XWKDD-CL161513
Build Number GINGERBREAD.XWKDD
crazy idea - is there any blocking going on in SA or with that carrier? Have you used another not carrier supplied smartphone successfully on that network?
I have been always using their 3g network on my iphone. And still there network only on edge connection on the s2. What i have noticed is that the saved apn sometimes shows up and sometimes disappears
omnia_owner said:
i own a samsung galaxy s2 ordered from uk,
everything working fine except for this serious issue that i have been trying to resolve till now.
i have a monthly internet subscription from my carrier and it always been working fine on my iphone ( i mean here connecting through the 3g network ). but in the S2 .. i have to use Edge to be able to access the internet ( the mobile network mode must be set to GSM only ). whenever i switch the network mode to GSM\WCDMA auto , the 3g icon appears but when it tries to connect to internet, the phone automatically switch to Flight mode and i loose the network signal. and this happens all the time. till now i am only able to connect to the internet by switching the mobile network mode to GSM only which only uses Edge network .
i have tried every possible thing to resolve this issue but nothing worked for me. please help
Click to expand...
Click to collapse
Hi, very similar issue here.
For this four days since I have got my GS2 everything was just fine. The data connection and 3G speed was great. Yesterday, all of the sudden all got crappy. Could not display any web pages. It starting to display page but after few seconds pop-up window appear which say "Data connectivity problem. The server failed to communicate. Try again later"
Interesting that my gmail, market, xda app working fine as normal.
I'm in Ireland on O2 now.
Baseband version I9100XXKDH
Kernel version 2.6.35.7--I9100XWKDD-CL161513
Build Number GINGERBREAD.XWKDD
Can someone help to solve the problem, please. Is it possible that something with the hardware is wrong? Broken?
I'll perform the factory reset and will let you know.
i just managed to flash my device with the latest EXE1 dated May 3.
and i am still facing the exact same problem.
omnia_owner said:
i just managed to flash my device with the latest EXE1 dated May 3.
and i am still facing the exact same problem.
Click to expand...
Click to collapse
Maybe we should ask for replacement...
I have same issue, and for Ihrrob, your other application are working fine because what i noticed on my mobile that 3G & 2G connection is there but not permenant that's why WIFI hotspot always disconnect and VOIP applications are not working.
Hassanalaa said:
I have same issue, and for Ihrrob, your other application are working fine because what i noticed on my mobile that 3G & 2G connection is there but not permenant that's why WIFI hotspot always disconnect and VOIP applications are not working.
Click to expand...
Click to collapse
You are right the 3G/2G connection is there but not permanent.
If I press the Internet icon the home page, which is 'Google' appears (sometimes) immediately. I think this is because the page is very light. If I try to open a regular page it loads 1/3 of the content or nothing.
i just hope it is a software bug not a hardware problem
Type on the dialpad *#*#4636#*#* and force the phone to HSDPA only on the dropdown menu. This is a hidden menu on the phone.
Isn't this carrier related?
amtrakcn said:
Isn't this carrier related?
Click to expand...
Click to collapse
Unfortunately not.
I have spoke to the rep in the store. They reset all settings for me but it didn't help.
Just to double check if he wasn't wrong I've put the sim card in to my N900 and all data worked fine.
Bad, bad...
omnia_owner said:
i am from saudi arabia and i am using Mobily network.
mobily is using HSDPA network as well as Edge network.
i did a software reset and still the same issue.
phone information:
Baseband version I9100XXKDH
Kernel version 2.6.35.7--I9100XWKDD-CL161513
Build Number GINGERBREAD.XWKDD
Click to expand...
Click to collapse
I'm on Mobily network in Riyadh, and 2G/3G is working fine for me. I stay on 2G most of the time to save battery, but have tested 3G and got around 3mbps.
I have the same Baseband, Kernel and Build number (rooted)
Are you using "Market Enabeler"? It can change your APN settings, and you need to restore the provider setting.
just rooted my device.
still same weird issue.
issue again: simply whenever my device tries to connect to H+ , the device automatically enters flight mode and automatically disable flight mode so that the signal bars come back without H+ and when i check back the saved APN i see nothing there ( thought i was there before ). and this strange behavior disappears when i switch the mode from GSM/WCDMA auto TO GSM only .. after i do this the device connects regularly to Edge network and i can browse the net.
so basicaly for me i will be only able to use the device on Edge instead of HSDPA or 3G.
im really hoping for help from here because i don't think i will find any help outside of this expert community.
regards
try to make it on obligatory 3G (WCDMA only) and check if the problem still there ..
still same problem juffo
i have noticed that another post are poping up talking about almost the same issure.
i hope a new firmware will fix this

[Q] Help! Diagnose network connection issues

Hi guys
My n9005 has been having mobile connectivity issues for a while now. I'm not very knowledgeable about mobile networking and standards so I need some help diagnosing the problem before I either find a setting to alleviate the troubles or get some hardware replaced. For your reference i think has been caused by dropping my phone quite a few times so there is likely a hardware issue, i just want to better understand it to see if theres a workaround before i go spending money!
My phone works flawlessly when it displays its connect to 4G or H+ networks. However when it drops to 3G it usually does not send or receive any texts, calls, and I have no data connection.
I have fiddled around in the service menus and tried setting the band preferences to GWL, WCDMA & GSM, LTE Only, etc etc, with not much luck either having no connection or having the same issue. For reference I don't have 4G coverage at my home only H+, but when I was on holiday in the middle of no where at the National Park (I live in New Zealand) I had 4G connections the entire time with no dropping.
Now I have no idea what mobile networks use what standards/protocols so if you could recommend a setting change or identify what I should get replaced that would be great!
Cheers

OnePlus Two - HSPA+ and 3G Data Connection Problem

Hi Everyone,
I'm usually just a reader on XDA, but I have found a problem that appears not to have been solved and wondered if anyone had any insight.
Problem Summary
When in an area (or network) with only HSPA and UMTS (strong HSPA/UMTS signal, but with no LTE or 2G available), the phone will drop from H+ to 3G erratically, always dropping the data connection. Traditional phone calls are not affected.
Detailed Description
I have a OnePlus Two and have 2 SIM cards. My first SIM Card is with Bell Canada (Virgin), and the second SIM Card is with WIND Mobile Canada.
Neither Bell nor WIND operate a 2G network, so the lowest the service can fall to is UMTS/3G.
Initially, I didn't notice the problem because Bell also operates an LTE network, and there is no problem with dropping the data connections when on LTE.
When I switched to the WIND SIM card (which only operates HSPA and UMTS), I noticed a problem where the phone would initially connect to H+, begin downloading whatever is needed (say, streaming music), but then part way through the download, the connection would switch to 3G, and the data would effectively stop. Within a minute, the service would jump back to H+ and download some more, but this cycle would continue (H+ --> 3G --> H+ --> 3G... ), with no way of knowing 1) how long the H+ connection would last before dropping to 3G (usually less than 30 seconds), and 2) after dropping to 3G, how long before going back to H+. This problem makes the phone almost useless when there is no LTE.
The most obvious troubleshooting I did was move to locations of better signal but I quickly ruled that out, as nothing seems to remove this problem. Other things I tried was to: move locations in the city, reboot phone, hard reset phone, flash most updated version of Oxygen, unlock bootloader, root, try the HSPA Keepalive app, swap SIM1 to SIM2, and many other things.
I originally thought this was a network issue, but I put this WIND SIM in another phone and there was no problem in any way that resembled this problem.
I also ruled out this being a network-specific problem, as I have taken a trip with the Bell SIM to an area where Bell does not have any LTE coverage (only HSPA and UMTS) and the same problem occurs on Bell as with the WIND SIM.
I have found people who had this problem on the OnePlus One tend to recommend using 2G to stabilize the connection, but this is not possible on Bell or WIND. That solution also would not provide adequate data speeds.
Remember this problem only affects data connectivity, as 3G traditional phone calls have no problems.
Question
Does anyone know if there is a way to adjust the conditions when the OnePlus Two will choose to switch from H+ to 3G?
Does anyone have any easier suggestions?
Thank you all in advance, because this rendering this phone almost useless when there is no LTE coverage.
I believe your problem is that phone it's dualsim standby, that means only one modem that alternates signal for both sims, I think normal would be alternating from faster network to slower network on sim without data.
Having to change to g3 between sims theres something stoped in the modem and data connection is also stopped.
You have no problem with voice calls because other sim is automatically turned off and unreachable.
There's nothing you can do if you're forced to only 3g on both sims
By 3g I mean 3g or h+ which to my knowledge are the same
Hope I was helpful and not wrong or more confusing
Sent from my ONE A2005 using Tapatalk
fburgos said:
I believe your problem is that phone it's dualsim standby, that means only one modem that alternates signal for both sims, I think normal would be alternating from faster network to slower network on sim without data.
Having to change to g3 between sims theres something stoped in the modem and data connection is also stopped.
You have no problem with voice calls because other sim is automatically turned off and unreachable.
There's nothing you can do if you're forced to only 3g on both sims
By 3g I mean 3g or h+ which to my knowledge are the same
Hope I was helpful and not wrong or more confusing
Sent from my ONE A2005 using Tapatalk
Click to expand...
Click to collapse
Thanks, I will try disabling the second SIM to see if there is a bug with the dual-sim...
What it currently does with the second SIM is it either shows "R" for roaming or just emergency only, but perhaps there is a software issue so I'll see if disabling the second SIM makes a difference.
biomedeng said:
Thanks, I will try disabling the second SIM to see if there is a bug with the dual-sim...
What it currently does with the second SIM is it either shows "R" for roaming or just emergency only, but perhaps there is a software issue so I'll see if disabling the second SIM makes a difference.
Click to expand...
Click to collapse
Though strange, this workaround fixes the issue. Thank you to fburgos for the suggestion!
So just in case anyone ever finds this issue creeps up on them, the solution is to DISABLE the SIM you are not using. It's not the most convenient workaround to swap SIMs, but the other SIM will be in Emergency Mode, so it really makes no functional difference.
On the technical side, it does appear that there is actually a bug in Android for a very uncommon network configuration. It will only appear in this exact configuration:
SIM1: Network has HSPA/3G only, no LTE or 2G to move to
SIM2: Network also only has HSPA/3G with no LTE or 2G
The non-data SIM does NOT connect to a roaming network (connects with "Emergency Only") - if it connects to a roaming 2G network, this problem does not happen.
The data SIM connects to HSPA/3G
Both SIMs are active
I'm not sure if this will happen anywhere else in the world other than having a WIND Mobile Canada SIM and Bell or TELUS Canada SIM
If anyone has insight on how to report this to Google, or someone else who can confirm my theory, that would be great!
Try this:
1. You need to make sure you have the correct LTE APN selected in mobile networks and LTE as preferred type.
2. Go to dialer and type in this: *#*#4636#*#*
3. Phone Information
4. Set Preferred Network Type to: LTE/GSM (PRL) - you an play with which one you wanna use but the one I said works for sure. on other roms I have" TD-SCDMA, GSM/WCDMA and LTE"
5. Now click TURN OFF RADIO and wait WAIT few secs. will that button turns to Turn Radio ON
6. Now TURN ON RADIO and wait
7. when u see the triangle for the signal is back, at least black , go down and lick SMSC REFRESH then UPDATE.
8. now just go back to APN settings and go into your LTE APN
9. Change Bearer to LTE
biomedeng said:
Hi Everyone,
I'm usually just a reader on XDA, but I have found a problem that appears not to have been solved and wondered if anyone had any insight.
Problem Summary
When in an area (or network) with only HSPA and UMTS (strong HSPA/UMTS signal, but with no LTE or 2G available), the phone will drop from H+ to 3G erratically, always dropping the data connection. Traditional phone calls are not affected.
Detailed Description
I have a OnePlus Two and have 2 SIM cards. My first SIM Card is with Bell Canada (Virgin), and the second SIM Card is with WIND Mobile Canada.
Neither Bell nor WIND operate a 2G network, so the lowest the service can fall to is UMTS/3G.
Initially, I didn't notice the problem because Bell also operates an LTE network, and there is no problem with dropping the data connections when on LTE.
When I switched to the WIND SIM card (which only operates HSPA and UMTS), I noticed a problem where the phone would initially connect to H+, begin downloading whatever is needed (say, streaming music), but then part way through the download, the connection would switch to 3G, and the data would effectively stop. Within a minute, the service would jump back to H+ and download some more, but this cycle would continue (H+ --> 3G --> H+ --> 3G... ), with no way of knowing 1) how long the H+ connection would last before dropping to 3G (usually less than 30 seconds), and 2) after dropping to 3G, how long before going back to H+. This problem makes the phone almost useless when there is no LTE.
The most obvious troubleshooting I did was move to locations of better signal but I quickly ruled that out, as nothing seems to remove this problem. Other things I tried was to: move locations in the city, reboot phone, hard reset phone, flash most updated version of Oxygen, unlock bootloader, root, try the HSPA Keepalive app, swap SIM1 to SIM2, and many other things.
I originally thought this was a network issue, but I put this WIND SIM in another phone and there was no problem in any way that resembled this problem.
I also ruled out this being a network-specific problem, as I have taken a trip with the Bell SIM to an area where Bell does not have any LTE coverage (only HSPA and UMTS) and the same problem occurs on Bell as with the WIND SIM.
I have found people who had this problem on the OnePlus One tend to recommend using 2G to stabilize the connection, but this is not possible on Bell or WIND. That solution also would not provide adequate data speeds.
Remember this problem only affects data connectivity, as 3G traditional phone calls have no problems.
Question
Does anyone know if there is a way to adjust the conditions when the OnePlus Two will choose to switch from H+ to 3G?
Does anyone have any easier suggestions?
Thank you all in advance, because this rendering this phone almost useless when there is no LTE coverage.
Click to expand...
Click to collapse
I have the same problem. Do you already have solved it?
I use only one SIM card so it is not a problem two cards.
really you do not have this problem? if no one knows the solution?
compared with my htc butterfly 2 and another low-end android, one plus 2 running latest Oxygen OS has serious connectivity issues. I compared the signals strength using same sim card in same location (including being connected to the same tower) and One Plus 2 keeps dropping the connection and has really poor signal strength. I have tried the *#*#4636#*#* and tried different network modes, but none of them are helping. Its a real disappointment that the basic feature of this phone is screwed up.
I have tried with CM13 as well. Any ideas if this is a modem version issue?
odeccacccp said:
Try this:
1. You need to make sure you have the correct LTE APN selected in mobile networks and LTE as preferred type.
2. Go to dialer and type in this: *#*#4636#*#*
3. Phone Information
4. Set Preferred Network Type to: LTE/GSM (PRL) - you an play with which one you wanna use but the one I said works for sure. on other roms I have" TD-SCDMA, GSM/WCDMA and LTE"
5. Now click TURN OFF RADIO and wait WAIT few secs. will that button turns to Turn Radio ON
6. Now TURN ON RADIO and wait
7. when u see the triangle for the signal is back, at least black , go down and lick SMSC REFRESH then UPDATE.
8. now just go back to APN settings and go into your LTE APN
9. Change Bearer to LTE
Click to expand...
Click to collapse
Did It.. But it seems like it didn't solve my problem..

Categories

Resources