Database Users

[Q] Low level format internal memory

For some reason my flexrom partition got corrupted and I would like to low level format, a normal format in cwm can't repair it. Currently I can only install rom that do not touch flexrom. Is this even possible? Any help would be greatly appreciated.

lowsum said:
For some reason my flexrom partition got corrupted and I would like to low level format, a normal format in cwm can't repair it. Currently I can only install rom that do not touch flexrom. Is this even possible? Any help would be greatly appreciated.
Click to expand...
Click to collapse
If you have your cuid number, you can go to the ics recovery thread, and nvflash the patched ics boot loader and recovery. I believe this will format all partitions and wipe the tablet clean leaving only the ics patched boot loader and cwm recovery.
Had to do it on mine yesterday as the leaked 501 updates fubarred all internal memory. No biggie.

Thanks for replying again moscow, I tried this method:
http://forum.xda-developers.com/showthread.php?t=1522384
I think that's the one you were talking about. I don't know why but my tab doesn't wake in "download mode" as specified. I do put it in apx with the reset/power combination but nothing happen when I enter my sbk. Strangely I can use apx with timmydean's 3.2.1 EEUs tool without problem but I can't with nflash...I succesfuly used nflash before to patch the bootloader and flash cwm when I tried the leak back then but it doesn't work anymore.
Something other than flexrom must be wrong...cmw always give me an error when formating flexrom though. At least the ICS rom that shall not be named work fine at least. As I said in my other thread, all leak based rom fail to boot...even the new cm9, probably because it use stock ics kernel. I hope the official ota update will fix it, but I doubt it because even the update.zip with stock recovery failed to boot. Thanks again for your assistance Moscow!

lowsum said:
Thanks for replying again moscow, I tried this method:
http://forum.xda-developers.com/showthread.php?t=1522384
I think that's the one you were talking about. I don't know why but my tab doesn't wake in "download mode" as specified. I do put it in apx with the reset/power combination but nothing happen when I enter my sbk. Strangely I can use apx with timmydean's 3.2.1 EEUs tool without problem but I can't with nflash...I succesfuly used nflash before to patch the bootloader and flash cwm when I tried the leak back then but it doesn't work anymore.
Something other than flexrom must be wrong...cmw always give me an error when formating flexrom though. At least the ICS rom that shall not be named work fine at least. As I said in my other thread, all leak based rom fail to boot...even the new cm9, probably because it use stock ics kernel. I hope the official ota update will fix it, but I doubt it because even the update.zip with stock recovery failed to boot. Thanks again for your assistance Moscow!
Click to expand...
Click to collapse
Well, when I fubarred my blocks, it took me a couple times till I figured out to nvflash from a normal windows cmd window, and not through adb!
Also, although my cuid numbers are different, they output the same sequence through vach's site.
Have you toggled data/media in cwm to completely format the tab?
Still I would try the nvflash for the patched boot loader. That should wipe that puppy clean.

Moscow Desire said:
Well, when I fubarred my blocks, it took me a couple times till I figured out to nvflash from a normal windows cmd window, and not through adb!
Also, although my cuid numbers are different, they output the same sequence through vach's site.
Have you toggled data/media in cwm to completely format the tab?
Still I would try the nvflash for the patched boot loader. That should wipe that puppy clean.
Click to expand...
Click to collapse
Ok I finally got it to enter download mode (I had some missing files) and start the flashing procedure but again with errors. I removed the CLS from the run.bat, so here is the ouput:
Code:
Generate your SBK with your CPUID from here : http://vache-android.com/v1/index.
php?site=sbk
Enter your SBK:0x97D71E00 0xD423C006 0x3B6A2404 0x027A2103
Loading bootloader...
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x037c6205447fe157
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 3
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714385/714385 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: Bct Write Failed (code: 22) message: nverror:0x8 (0x11000008)
flags: 0
**********************************************************
* Press any key when your A500 is in bootloader mode *
**********************************************************
Press any key to continue . . .
Flashing patched bootloader V2...
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
Nvflash started
[resume mode]
So if im right partition 4 is bootloader, hope that helps..Thanks!

lowsum said:
Ok I finally got it to enter download mode (I had some missing files) and start the flashing procedure but again with errors. I removed the CLS from the run.bat, so here is the ouput:
Code:
Generate your SBK with your CPUID from here : http://vache-android.com/v1/index.
php?site=sbk
Enter your SBK:0x97D71E00 0xD423C006 0x3B6A2404 0x027A2103
Loading bootloader...
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x037c6205447fe157
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 3
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714385/714385 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: Bct Write Failed (code: 22) message: nverror:0x8 (0x11000008)
flags: 0
**********************************************************
* Press any key when your A500 is in bootloader mode *
**********************************************************
Press any key to continue . . .
Flashing patched bootloader V2...
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
Nvflash started
[resume mode]
So if im right partition 4 is bootloader, hope that helps..Thanks!
Click to expand...
Click to collapse
I don't know. But clearly something is amiss. When you converted your UID on Vache's site, the new ICS UID converted number, should have been the same as your original UID number. Can you verify? (the 2 UID numbers have the same output)
Example;
0x038061c7409fa617 (HC)
0x79531F00 0xBB680C01 0xFB22E803 0x8ADE2003
38061c7409fa617 (ICS)
0x79531F00 0xBB680C01 0xFB22E803 0x8ADE2003
For some reason, mine stayed the same.
Best bet, run this by Drellisdee on his RA Recovery thread. He;s the master of this, and maybe he has some insight.

A500
Hello lowsum.
I also have this problem as you. Did you find a solution?
"Flashing bootloader: bootloader_v8.bin ...
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x120002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
Nvflash started
[resume mode]"

Another A500 stuck in APX

Hey guys for the past 5 months I`ve been trying to unstuck my A500 from teh APX mode, and still no luck.
I have my CPUID/SDK, I`ve used every methodthat I know to unstuck it but I never managed it.
Can anyone share me a light? And in the case of sending it for Acer, can anyone say if is an firmware or hardware problem?
*Notes:
It all happened after I tried to intall a custom ics rom (based on stock ics rom) because that acer was delaying the launch on my country.
On the nvflash program , I get the following error
Flashing bootloader: bootloader_v8.bin ...
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
Nvflash started
[resume mode]
On the A500APXFlash program freezes on Step 2 uploading image.
thx in advance

caio492 said:
Hey guys for the past 5 months I`ve been trying to unstuck my A500 from teh APX mode, and still no luck.
I have my CPUID/SDK, I`ve used every methodthat I know to unstuck it but I never managed it.
Can anyone share me a light? And in the case of sending it for Acer, can anyone say if is an firmware or hardware problem?
*Notes:
It all happened after I tried to intall a custom ics rom (based on stock ics rom) because that acer was delaying the launch on my country.
On the nvflash program , I get the following error
Flashing bootloader: bootloader_v8.bin ...
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
Nvflash started
[resume mode]
On the A500APXFlash program freezes on Step 2 uploading image.
thx in advance
Click to expand...
Click to collapse
Do a search for "babsector", you will find exact references to the same error messages you are getting. It seems your partition table got corrupted, and now you can't write to it because it is corrupted, so babsector (misspelled badsector?) rewrites the partition table in a different location, and a different size, then re-creates it back in the correct location, thus fixing your problem. (Or something along those lines, but it will def fix your problem)
Don't forget to click "Thanks" if this fixes you up. (Tip, maybe, a lot of noobs at flashing, forget to root their tablet before flashing, thinking the flash will give them root. This is the cause for many of these first time flashers ending up in APX.)
badsector or babsector, can be found at:
http://narod.ru/disk/53919831001.a235ea2225f319015f30c009629d2075/BabSector.rar.html

Danny2 said:
Do a search for "babsector", you will find exact references to the same error messages you are getting. It seems your partition table got corrupted, and now you can't write to it because it is corrupted, so babsector (misspelled badsector?) rewrites the partition table in a different location, and a different size, then re-creates it back in the correct location, thus fixing your problem. (Or something along those lines, but it will def fix your problem)
Don't forget to click "Thanks" if this fixes you up. (Tip, maybe, a lot of noobs at flashing, forget to root their tablet before flashing, thinking the flash will give them root. This is the cause for many of these first time flashers ending up in APX.)
badsector or babsector, can be found at:
http://narod.ru/disk/53919831001.a235ea2225f319015f30c009629d2075/BabSector.rar.html
Click to expand...
Click to collapse
Thx for the response, I ran both .bat files on the folder, still I get error messages (listed below).
I`ve tried to run the nvflash.exe, but it opens and closes instantly.
Sorry if I done something wrong, I dont have much exp. on these subjects and the folder didnt present instructions how to proceed.
Error messages:
A501 A.bat:
Tablet enters in Acer download mode (Acer logo on the middle)
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x03806248436154d7
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: failed to create the partition (code: 10) message: nverror:0x
5 (0x1000005) flags: 0
A501 B.bat:
Tablet enters in Acer download mode (Acer logo on the middle)
Same message as above.

caio492 said:
Thx for the response, I ran both .bat files on the folder, still I get error messages (listed below).
I`ve tried to run the nvflash.exe, but it opens and closes instantly.
Sorry if I done something wrong, I dont have much exp. on these subjects and the folder didnt present instructions how to proceed.
Error messages:
A501 A.bat:
Tablet enters in Acer download mode (Acer logo on the middle)
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x03806248436154d7
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: failed to create the partition (code: 10) message: nverror:0x
5 (0x1000005) flags: 0
A501 B.bat:
Tablet enters in Acer download mode (Acer logo on the middle)
Same message as above.
Click to expand...
Click to collapse
Sorry, I am by no means an expert, but babsector has always fixed the problem for me when the error was " Command Execution failed cmd 13, error 0x12 0002"
I have not seen anyone that had the error "failed executing command 16 NvError 0x120002" come away without having to change out the Motherboard. Can't hurt to try again, sometimes it takes a couple tries to make it go. If it doesn't go, maybe you might need a new motherboard.

Danny2 said:
Sorry, I am by no means an expert, but babsector has always fixed the problem for me when the error was " Command Execution failed cmd 13, error 0x12 0002"
I have not seen anyone that had the error "failed executing command 16 NvError 0x120002" come away without having to change out the Motherboard. Can't hurt to try again, sometimes it takes a couple tries to make it go. If it doesn't go, maybe you might need a new motherboard.
Click to expand...
Click to collapse
Then its a dead tablet because the technical assistance on my country doesn`t have motherboards, bad luck then

[Q] bootloader status: Bct Write Failed (code: 22)

Please help!
I tried to update the bootloader to v9 but after installing the zip file thru cwm, rebooted it said flashing failed and black screen.
I can only get to APX mode.
When I use the blackthund3r_A500_APX_Flash_Tool to flash, it did not detect the APX mode but I can see the APX device from windows. The process hang in EBT stage 2 - uploading image.
So I tried to nvflash. I can enter the nvflash mode ok:
C:\Android\A500\V8-UNL-ICS-HC-bootloader-MULTI-cwm>nvflash --bct bct.bct --setbct --sbk xxxxx xxxxx xxxxx xxxxx--configfile flash.cfg --bl bootloader_apx.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x037c61c041xxxxxx
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader_apx.bin
| 714981/714981 bytes sent
bootloader_apx.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
I can extracted the partition table:
C:\Android\A500\V8-UNL-ICS-HC-bootloader-MULTI-cwm>nvflash -r --getpartitiontable ptable.txt
Nvflash started
[resume mode]
Succesfully updated partition table information to ptable.txt
The partition 4 is:
PartitionId=4
Name=EBT
DeviceId=18
StartSector=896
NumSectors=1024
BytesPerSector=4096
When I try to format partition 4, it failed:
C:\Android\A500\V8-UNL-ICS-HC-bootloader-MULTI-cwm>nvflash -r --format_partition 4
Nvflash started
[resume mode]
Formatting partition 4 please wait.. done!
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: Bct Write Failed (code: 22) message: nverror:0x42008 (0x6042008) flags: 0
I reconnected nvflash and try to download the bootloader to partition 4, still failed:
C:\Android\A500\V8-UNL-ICS-HC-bootloader-MULTI-cwm>nvflash -r --download 4 bootloader_v8.bin
Nvflash started
[resume mode]
sending file: bootloader_v8.bin
| 1191932/1191932 bytes sent
bootloader_v8.bin sent successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: Bct Write Failed (code: 22) message: nverror:0x42008 (0x6042008) flags: 0
Can anyone help me please? I can only go to APX mode

MY partition 4 is my Bootloader and I think it is corrupted. I cannot download or format it.
PartitionId=4
Name=EBT
DeviceId=18
StartSector=896
NumSectors=1024
BytesPerSector=4096
But I tried to run nvflash --rawdeviceread and then --rawdevicewrite, it can finished without errors:
C:\Android\A500\V8-UNL-ICS-HC-bootloader-MULTI-cwm>nvflash -r --rawdeviceread 896 1024 p_4.txt
Nvflash started
[resume mode]
failed executing command 30 NvError 0x120002
command failure: readdeviceraw failed (bad data)
C:\Android\A500\V8-UNL-ICS-HC-bootloader-MULTI-cwm>nvflash -r --rawdevicewrite 896 1024 p_4.txt
Nvflash started
[resume mode]
sending file: p_4.txt
/ 4194304/4194304 bytes sent
p_4.txt sent successfully
Can someone extract the partition 4 EBT into a file so that I can try to write it on my A500? Please Help!

[Q] please help in thinkpad tablet

thanks for the all in xda-developer​
please help me to slove this problem with lenovo
i have this messege when i boot into recovery ( lenovo thinkpad tablet 183922g )
Code:
E: can't mount /cache/recovery/command
E: can't mount /cache/recovery/log
E: can't open /cache/recovery/log
E: can't mount /cache/recovery/last_log
E: can't open /cache/recovery/last_log
I try use nvflash with this and i have this ok
Code:
C:\nvflash>nvflash -w --bl 04.EBT.img --go
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x0a80518541dfd597
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 0
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: 04.EBT.img
/ 6291456/6291456 bytes sent
04.EBT.img sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
I try use nvflash to get partition table and i have this
Code:
 BCT     PT      EBT      GP1      SOS      LNX      APP     CAC   „ 
MSC  *    PIA  ¢    SEC  ¢  
USP  ¶ Œ   PDA  B    UDA  V \1   GPT  ²:  
I try use nvflash to load new rocovery image i have this message
Code:
C:\nvflash>nvflash -r --download 6 recovery.img
Nvflash started
[resume mode]
sending file: recovery.img
/ 5462016/5462016 bytes sent
recovery.img sent successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: Bct Write Failed (code: 22) message: nverror:0x42008 (0x6042008) flags: 0
please how to solve this problem​

[Q]PB Liberty Tab Recovery Help Needed Stuck

HI, I have been working on the PB Liberty Tab G100 for over a week.. I just want it back to stock.. no custom boot loaders or roms etc.. just so they can use it..
the story so far... I was asked to repair a PB liberty tab that was supposedly just freezing.. I think it had a custom boot V8..
Recovery was not working just getting the android dube with red triangle.. so installed thor recovery via fastboot..
tried the update method.. did not work.. tried everything.. but was having an issue with the wiping and formating...
I managed to finally get the cpuid by using a 64 bit version of ubuntu and have managed to get the SBK.. tried the recommended flashs A500 apx etc
but now i'm stuck in apx mode.. when i try to use V8-UNL-ICS-HC-bootloader-MULTI-cwm method I get the failed to format..
info found from this thread http://forum.xda-developers.com/showthread.php?t=1751978
**********************************************************
* Press any key when your A500 is in bootloader mode *
**********************************************************
Press any key to continue . . .
Flashing HC-Bootloader...
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
Nvflash started
[resume mode]
I think I have an internal storage issue, or bad sectors.. or I am just not using the right apx.. and help would be awesome..
i have read so many forum sections and pieced together which has finally got me into the device.. but now I seem to have hit a brick wall..
so help i have tried to track down the bad sectors software to run in apx mode but cant seem to find it al all the link i have found are dead..
quick update
**********************************************************
* Make your choise: *
*(1) ICS bootloader V8 with TWRP-2.1.3-ICS cwm(touch cwm)*
*(2) ICS bootloader V8 with PubRecovery-v0.2 (BareBones) *
*(3) ICS bootloader V8 with Thor-1.7cwm (touch cwm) *
*(4) ICS bootloader V8 with Thor-1.7.3 NEW cwm(touch cwm)*
* with its compatible recoveries. *
**********************************************************
(1 2 3 4):4
Loading bootloader...
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c62484260****
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader_apx.bin
| 714981/714981 bytes sent
bootloader_apx.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: Bct Write Failed (code: 22) message: nverror:0x42008 (0x60420
08) flags: 0
*****************************************************************
* Press any key when your A500/501/G100W is in bootloader mode *
*****************************************************************
Press any key to continue . . .
UPDATE
I have tried running Badsector but all i get it this.. I have checked the correct drivers are installed.. but just seem to be stuck..
I am thinking my internal storage is fried..
****************************************************************
* Before executing, be sure to delete recovery-from-boot.p *
* from /system to ensure recovery will stick *
****************************************************************
****************************************
* Reboot your tablet into APX mode *
****************************************
Generate your SBK with your CPUID from here :
http://vache-android.com/v1/index.php?site=sbk
Enter your SBK:0x****1E00 0x0**51700 0xEB*****2 0x682*****
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c624842601397
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
creating partition: PT
creating partition: APP
creating partition: EBT
creating partition: GP1
creating partition: SOS
creating partition: LNX
creating partition: CAC
creating partition: MSC
creating partition: FLX
creating partition: AKB
creating partition: UDA
creating partition: GPT
failed executing command 12 NvError 0x120002
command failure: create failed (bad data)
bootloader status: fatal failure to read / write to mass storage (code: 9) messa
ge: nverror:0x8 (0x19000008) flags: 0
Press any key to continue . . .