Related
Hello everyone
I have a LG L5 and I went install a custom ROM.
I was been ROOT, nothing problems, after I try install CWM, but my phone brick.
In the screen only I could only see the LG Logo and the legend ''downloading''
Next, I was try with KDZ Updater, and LG Update Tool, but didn't work.
In my despair, I was try with LG Flash Tool, but with a ROM different of my phone.
Now, my phone is dead, when I connect to my PC only I can see ''unknown device'', no one signal of life.
Thanks for you help
Sorry for my bad english
Take out battery.
Volume DOWN or Volume UP dont remember wich one but one of them for sure.
Plug USB cable from PC to phone WITHOUT battery it should start in emergency mode if TOTALLY not dead
Then flash correct KDZ firmware via KDZ tool
struart said:
Take out battery.
Volume DOWN or Volume UP dont remember wich one but one of them for sure.
Plug USB cable from PC to phone WITHOUT battery it should start in emergency mode if TOTALLY not dead
Then flash correct KDZ firmware via KDZ tool
Click to expand...
Click to collapse
Sorry for response late, I try this method, but no life signals, only one sound on my PC, and the "unknown device'' I was re-install the drivers with LG mobile support tool
i have a bricked lg g2 d802t after ota update.
phone was recongnised from pc as qhsusb_bulk but after ubuntu method posted here Fix No recovery, download mode.. i think i made a mistake flashing boot partition?
now phone wont turn on, no download mode, recovery mode or anything else, but when connected to pc it shows qhsusb_bulk in the device manager, but the is still off and wont turn on.. do you have idea to fix this problem? please help me
anybody is experiencing the same state as i have? please help..
which partitions did you flash ?
bender_007 said:
which partitions did you flash ?
Click to expand...
Click to collapse
i only followed the instructions here and flashed the provided .img by the way im on official kitkat firmware, the provided .img is for jb right? do you think this can be still fix without going to service center? :crying:
scout1089 said:
i only followed the instructions here and flashed the provided .img by the way im on official kitkat firmware, the provided .img is for jb right? do you think this can be still fix without going to service center? :crying:
Click to expand...
Click to collapse
Flash only aboot, boot, laf. You need the d802T for aus i think.
bender_007 said:
Flash only aboot, boot, laf. You need the d802T for aus i think.
Click to expand...
Click to collapse
how can i do that? because i dont have download mode, nor the phone turns on, pc wont detect or recognize the phone anymore when connected, all i got is qhsusb_bulk in the device manager and no multiple drives shown in my computer like before, also ubuntu wont recognize nor detect it also.. :crying:
Try with knoppix m8.
bender_007 said:
Try with knoppix m8.
Click to expand...
Click to collapse
can you provide the link for the knoppix m8?
so im going to run this instead of ubuntu and follow the same instructions stated on the tutorial mentioned? and only flash the 3 .img aboot, boot, laf? am i right? so im going to extract the kdz in order to get the 3 .img specific to my device?
http://knoppix.net/get.php just the 3. Find your original kdz m8
bender_007 said:
http://knoppix.net/get.php just the 3. Find your original kdz m8
Click to expand...
Click to collapse
im going to extract the D802T kdz and get the 3 .img from it? sorry still a noob and could you please explain and guide me through?
edit: after booting with knoopix, inserted the phone still cant be read.. i found no biggest number and all numbers are the same 1-15, seems it did'nt detect the phone, please help
can someone else who manage to revive their phone help me?
please help
i didnt get it ..
ur pc recognize the device as qhsusb ? or doesnt recognize it at all ?
rotem11 said:
i didnt get it ..
ur pc recognize the device as qhsusb ? or doesnt recognize it at all ?
Click to expand...
Click to collapse
when connected to pc, it displays qhsusb_bulk in the device manager and nothing no multiple drives, the phone does not turn on but i think its on even though the screen looks dead because when i left it for an hour i felt the phone's battery is warm..
try go ubuntu and follow this guide http://forum.xda-developers.com/showthread.php?t=2681089
maozer said:
try go ubuntu and follow this guide http://forum.xda-developers.com/showthread.php?t=2681089
Click to expand...
Click to collapse
already did ubuntu wont detect the phone
can u try ubuntu with vmware?
maozer said:
can u try ubuntu with vmware?
Click to expand...
Click to collapse
im using the usb method, if the usb method didnt detect the phone so i guess the vmware wont too?
also tried knoppix it wont detect the phone's partition
well i had the exact same problem u have.. you can look at my previous posts..
i dont know why but it worked for me with vmware.. and in ur situation it worth a shoot.
one of the Initial Symptoms are qhsusb.. try it and let me know..
maozer said:
well i had the exact same problem u have.. you can look at my previous posts..
i dont know why but it worked for me with vmware.. and in ur situation it worth a shoot.
one of the Initial Symptoms are qhsusb.. try it and let me know..
Click to expand...
Click to collapse
okey i'll give it a shoot.. thank you
How to Fix "error device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer. You need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
How to fix “No response from the device. Check PMIC first and
if still boot problem, replace AP.”
Remove battery and connect again put qualcomm 9008 then use tool in topic
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-all-variants/ Just as helping
[*]I see very topic unbrick qualcomm 9008 lg g2, lg g3 but all tool can not use.
I have full tool board ver 2.9.( only 2.9).
Link download drive.google.xxx /file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view?usp=sharing (xxx= com)
Support lg g2, lg g3 workking 100%.
Download tool, open BoardDiag and choose file tot correct model phone of you( you can download tot in xda)
See guide in pictrure : very easy.
Note
Hold power 2 minute and connect cable ( or remove battery)>>And open tool check ap, emmc test again
Then unbrick done remove cable, hold power 30 second and hold volume up connect cable phone put downloadmod >> Use lgflashtool 1.5 flash file tot again >> done.
If done pls donate a few beers paypal of my Thank you very much.
Man you saved my ass Thank you so much !1 when i get my salary ill donate to you and tell everybody to do so cuz this tool is amazing. im in download mode now ill try to flash with lg flash tool.
Thank so much man but my g3 last week unbrick qualcomm i had I submit for warranty[emoji24] [emoji24] I am very Star-crossed [emoji20]
Hello friend willcracker
Hello friend willcracker :good:
I hope all is well;
I saw this little tutorial so I want to ask for help
I have a LG G3 D855p and my phone is dead (bricked)
I can not quite understand the method you friend
not turn on my phone
I can not enter the "" Download Mode ""
VOL + Up when I connect the USB cable to the PC recognizes me as:
Qualcomm HS-USB QDLoader 9008 (COM10)
why I ask for help to revive my g3
If you help me ... .. I promise to donate something for you
you send a file "picture" attached
- - As I can get to "" Fastboot Mode "" on my phone
I hope your prompt response, please do not ignore my message :crying:
greetings from peru
You need to Disassemble Phone and Expose the TP Location
See pictrue
Expose the TP Location.
Done phone put qualcom 9008>> use tool unbrick
Remeber unplug battery connect only cable and short testpoint
Thanks for responding, but I need your help please friend
Hello willcracker I have no such tool you indicate "tool unbrick testpoint"
I could do this step with some type of cable or wire?
- If you Might tell me how to do that step with another option
leave your email. to chat google chat (Houngts) and you help me please
I'm worried because my g3 d855p not light, or anything like I said ....
await your prompt response, I hope you can help me
TOT Firmware, must match installed version?
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
Lollipop was installed, goal was to move to a custom rom (blisspop v2.3)
Rooting was successful
Install of twrp not, reboot into recovery caused the 'signature verification error'
Tried to flash the kitkat rom via the download method, failed, ...
Currently, I have the same verification error also when trying to get into download mode and have the Qualcomm HS-USB QDLoader 9008 in my device manager.
I have the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0.tot file and did the first step of your procedure. Can I do the second step with this extract of kitkat even if lollipop was installed?
any feedback greatly appreciated!
Hello willcracker thanks, thanks for reply but I need your help please
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
Greetings from Peru
Click to expand...
Click to collapse
NO you need find google how do short testpoint samsung n7100 you see they guide short testpoint . Lg when short testpoint phone detect qualcomm 9008
And you use tool board diag unbrick.
???
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
Click to expand...
Click to collapse
I'm in the same boat! Could you please explain it a little better?
frank.devliegher said:
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
any feedback greatly appreciated!
Click to expand...
Click to collapse
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Ahh now i see!
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
sourly64 said:
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
Click to expand...
Click to collapse
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
Model Lg d851? writh
rememer ber tool suppoer only lg g3 f400s/l/k , lg d855 16gb and 32gb.
If use tool say error pcmic on tool not support (Ex: lg d851)
I up load only msm8974ac g3 msm8975ac g3 no upload
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
It seems won't work.I have gone through about this problem.Alway AP Check fail.QPST reported that phone had been in Sahara download mode for few seconds.A RMA fix my phone.But it cost me about 50dollars
willcracker said:
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Click to expand...
Click to collapse
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
TOT Version
willcracker said:
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Click to expand...
Click to collapse
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
frank.devliegher said:
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
Click to expand...
Click to collapse
YES you can use tot kikat unbrick .
sourly64 said:
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
Click to expand...
Click to collapse
sr i have not upload hex lg gpro waitting comming soon.
Hi,
I was installing MIUI v6, it did got install but many things were not working.
So i did the stupid thing and changed the kernal through twrp.
And NOW:
My phone is bricked, it stays on the LG logo.
I tried to go into downloading mode but it does not detect the usb to computer connection.
So I am unable to to use LG tool to install stock rom kdz.
because it does not detects the usb in downloading mode....
please help me around this problem.
my warrenty is over too.
qam47 said:
Hi,
I was installing MIUI v6, it did got install but many things were not working.
So i did the stupid thing and changed the kernal through twrp.
And NOW:
My phone is bricked, it stays on the LG logo.
I tried to go into downloading mode but it does not detect the usb to computer connection.
So I am unable to to use LG tool to install stock rom kdz.
because it does not detects the usb in downloading mode....
please help me around this problem.
my warrenty is over too.
Click to expand...
Click to collapse
I got the same problem here after using MIUI and trying to get out of it.
Stuck in bootloop, no recovery, download mode stuck at first screen, phone not being detected by pc and no flashing led anymore.
Anyone help us please, my phone is out of warranty too
http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
everything you need is here.
check again if you don't have USB connection of any kind. If you do have something in the PC responding to the G2 being connected, it isn't a hard brick and you can fix it with this: http://forum.xda-developers.com/showthread.php?t=2582142
Otherwise you just have to do this short the caps thing. Be careful and renember that this is always a better option than staying with a bricked device. You can also try to give the phone to some experienced repaired and tell him about the method and how will it cost.
Rayaxe said:
http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
everything you need is here.
check again if you don't have USB connection of any kind. If you do have something in the PC responding to the G2 being connected, it isn't a hard brick and you can fix it with this: http://forum.xda-developers.com/showthread.php?t=2582142
Otherwise you just have to do this short the caps thing. Be careful and renember that this is always a better option than staying with a bricked device. You can also try to give the phone to some experienced repaired and tell him about the method and how will it cost.
Click to expand...
Click to collapse
Thanks for the reply.
But it says:
http://forum.xda-developers.com/showthread.php?t=2582142
VERY IMPORTANT!!!!!!!
You must use the img files that correspond to the ROM you have installed before getting the problem to avoid breaking your phone. The link above is for 10b_EUR_16G firmware version. So don't use those files if your firmware version was not that one. Instead you should look for img files corresponding to the current version installed in your phone. If you don't know what version you've installed then don't use this method because you will break your phone.
Click to expand...
Click to collapse
and i dont know which one to download.
Here is the link to Miui 6, I did install before crashing
http://forum.xda-developers.com/lg-g2/development/kk-miui-6-lg-g2-variants-based-stock-lg-t3106569.
...
You have to know which model your phone is.
Do you know your phone's IMEI? http://www.lgkdz.com/ Go here and it will get the file you need to download via your IMEI (even though it is risky to put the IMEI in the internet).
Otherwise you can just search for your kdz file by knowing what model you have and what stock rom you had last time. You can always revert to that.
Mine is D802 32GB, has V30b-EUR software. That is enough for me to get the correct kdz file even by searching in the links provided in the tutorials I mentioned in my last message
Rayaxe said:
You have to know which model your phone is.
Do you know your phone's IMEI? http://www.lgkdz.com/ Go here and it will get the file you need to download via your IMEI (even though it is risky to put the IMEI in the internet).
Otherwise you can just search for your kdz file by knowing what model you have and what stock rom you had last time. You can always revert to that.
Mine is D802 32GB, has V30b-EUR software. That is enough for me to get the correct kdz file even by searching in the links provided in the tutorials I mentioned in my last message
Click to expand...
Click to collapse
My phone is bootlooping and recognized as "LGE Android MTP Device" only,
I can't back to stock using kdz, can't ADB sideload
Any ideas how to solve it?
GoPogoOreo! said:
My phone is bootlooping and recognized as "LGE Android MTP Device" only,
I can't back to stock using kdz, can't ADB sideload
Any ideas how to solve it?
Click to expand...
Click to collapse
Do you have access to download mode? Since your PC recognizes the phone as MTP Device, I'm not sure but I think that's only possible if you have /system/ working since the other partitions don't have MTP support originally.
If you have that, go there: http://forum.xda-developers.com/showthread.php?t=2432476
Flash with the tot method and you should be good to go.
But wait for someone who can confirm what I'm saying since I'm no expert.
Rayaxe said:
Do you have access to download mode? Since your PC recognizes the phone as MTP Device, I'm not sure but I think that's only possible if you have /system/ working since the other partitions don't have MTP support originally.
If you have that, go there: http://forum.xda-developers.com/showthread.php?t=2432476
Flash with the tot method and you should be good to go.
But wait for someone who can confirm what I'm saying since I'm no expert.
Click to expand...
Click to collapse
I can access download mode, but when i connect my phone (on download mode) to my PC nothing happened, and my phone is not detected even as MTP device
GoPogoOreo! said:
I can access download mode, but when i connect my phone (on download mode) to my PC nothing happened, and my phone is not detected even as MTP device
Click to expand...
Click to collapse
samething with me please help
Hi to all
I am wonder if there are ways to reflash the stock KDZ file since don't have fastboot, bootloader or even recovery, only black screen and a sort of com port recognized as RELINK-HS-USB like attached image.
I try with B2B program but, no support.
any solutions will be thanked, in case of fixed, will join development!
Have you tried LG Flash Tool 2014. Here is a webpage with all LG Leon 4G LTE firmware: http://lg-phone-firmware.com/index.php?id_mod=171
Here is a guide on how to download allow) for your phone (not recommended because your version may not be supported): http://forum.xda-developers.com/leon/how-to/how-to-update-lg-leon-h340n-to-android-t3393648
Here is a guide on how to install the original firmware for your phone(lollipop): http://forum.xda-developers.com/leon/how-to/helpful-guide-to-stock-t3211208
If you have any questions ask me, if you want, I hope I helped you
Nickblorck said:
Have you tried LG Flash Tool 2014. Here is a webpage with all LG Leon 4G LTE firmware: http://lg-phone-firmware.com/index.php?id_mod=171
Here is a guide on how to download allow) for your phone (not recommended because your version may not be supported): http://forum.xda-developers.com/leon/how-to/how-to-update-lg-leon-h340n-to-android-t3393648
Here is a guide on how to install the original firmware for your phone(lollipop): http://forum.xda-developers.com/leon/how-to/helpful-guide-to-stock-t3211208
If you have any questions ask me, if you want, I hope I helped you
Click to expand...
Click to collapse
i just try it, it's not working, the problem is showing the usb device, connected as port com, when I click on Read Phone Information, didn't work. thanks for the answer by the way
haky 86 said:
i just try it, it's not working, the problem is showing the usb device, connected as port com, when I click on Read Phone Information, didn't work. thanks for the answer by the way
Click to expand...
Click to collapse
have you changed the phone com port to 20 ???
Into lg flash tool i only connected my lg leon via usb and it automatically entered in download mode