Related
So I am not to NOOB but I sure acted like it last night when I was way tired and tried to flash a ROM. Here is what I did...
I didn't catch that I didn't have the CWM but that I had booted into the stock recovery tool... Well I didn't before it was to late that is...
I clicked WIPE DATA
I clicked WIPE CACHE
Then noticed there was no "install from SD"
So it seems like whatever I find to install from ODIN I can't get the CWM to install so I can then flash a ROM!
I need my phone up for work, I am in HOT SH!T!
How can I either flash a rom via stock recovery "update format" OR install CMW via ODIN?
PLEASE HELP ASAP!!
Thank you
why don't you just flash again via odin and then root your phone via odin as well?
Don't quite understand whats your problem. So what if you wiped data and cache the rom is still there. Reboot normally and flash cfroot according to your firmware and then you should have cwm up and running. After that flash desired rom and the end.
Sent from my GT-I9100 using xda premium
Flash one of the CF-Root kernels through Odin, whichever one matches the firmware you're running. They have CWM baked in, along with root so you can flash a ROM afterwards.
If you can't get into download mode, turn your phone off, plug it in and hold down + power + home and it should boot into download mode. Then you can flash with Odin.
I thought the same thing, that so what that I wiped them... but when I rebooted the phone it just sits at the "Rethink possible screen"
I can get into download mode and I did find the "cf" post but I dunno what kernel I am running as I can't boot to go into settings to seek.
if you in recovery mod choose reboot, and it will be ok, than read: http://forum.xda-developers.com/showthread.php?t=1103399,
or put in download mod: turn your phone off, hold down + power + home. Then flash with Odin.
I know you probably don't want to, but you can try doing a factory reset, that should allow you to get your phone up and running. If you have gmail installed it should put all your contacts back, as long as you backed up to gmail.
If you have an old copy of titanium backup you won't loose ALL your apps, this is why I tend to back up every weekend, I'm only a week behind with everything if problems arise....
Cheers...
Flash stock rom... Download cwm and flash with odin.... Then instal rom u want with cwm...
Sent from my GT-I9100 using xda premium
like I said, I am not a noob, just made a mistake...
I found the cf-kernel page, but I dunno what kernel I am running and so I dunno what kernel to flash (It seems vital)
"just rebooting" don't work lol I wish... it hangs at the "rethink possible" boot screen...
I was rooted but running the stock rom, if I can get CWM installed I think I will be golden, but whatever I seem to flash from ODIN don't work :-( no matter what nothing will flash as "PDA" but when I flash using "phone" it seems to install "zimage" which is the embedded file and succeeds and phone reboots... but still only to the rethink possible point.
flash any stock firmware then flash supercore 2.0 and do whatever you want from there
Think i know what the problem is,i have same issue sometimes,try flashing anogher rooted Kernel through odin,make sure its like if the rom is a kj3 that it has a kj3 kernel.see if that works
ultramag69 said:
you can try doing a factory reset... Cheers...
Click to expand...
Click to collapse
Be glad to but it isn't an option in the recovery?
My options are as follows...
Reboot system now
Apply update from SD
Wipe/reset
Wipe/cache
been in similar, if not same situation, things were missing from cwm recovery, like you wrote...if memory serves me fine,
flash stock fw with pit, repartition and everything...
then some rootec kernel with recovery...
Oh sh!t... just flashed the pit file here... http://www.darkyrom.com/community/i...-with-odin/#download-a-pit-file-for-the-i9100
and odin said success... and screen went black.
Not responding at all now :-(
let's go in a safe way...as long as you have download mode, you're OK.
Go to samfirmware or somewhere on XDA and find FULL STOCK FIRMWARE with proper .pit file and flash it with odin. Not kernel, not anything that is not full rom.
since you state that you are not noob, you know what from there.
abovenbeyond said:
Oh sh!t... just flashed the pit file here... http://www.darkyrom.com/community/i...-with-odin/#download-a-pit-file-for-the-i9100
and odin said success... and screen went black.
Not responding at all now :-(
Click to expand...
Click to collapse
What on earth are you doing?
It clearly states:
I9000 & I897 owners (not I91000!!!) may also need a PIT file (also included in RE ROM ZIP files). I will explain further what it's for.
Why didn't you follow a tutorial on xda? Can you boot in download mode?
borstri said:
let's go in a safe way...as long as you have download mode, you're OK.
Go to samfirmware or somewhere on XDA and fin FULL STOCK FIRMWARE with proper .pit file and flash it with odin. Not kernel, not anything that is not full rom.
since you state that you are not noob, you know what from there.
Click to expand...
Click to collapse
Sounds amazing but after my post above I not can't get the phone to power on although I hear the laptop detect it as I attempt to power down or up, but no screen or led display...
Really worried now... ****!
Lennyz1988 said:
What on earth are you doing?
It clearly states:
I9000 & I897 owners (not I91000!!!) may also need a PIT file (also included in RE ROM ZIP files). I will explain further what it's for.
Why didn't you follow a tutorial on xda? Can you boot in download mode?
Click to expand...
Click to collapse
I flashed this...
Download a PIT file for the I9100
Download EXT4.pit file (2KB)
(for the S2 only)
battery pullout, then three button combo for download
Help!
I need some advice. I had stock 4.2.2, flashed omega v14 and then 4.3 GE ROM. I did not know about knox and I have tripped it. It shows 0x1 now. I understand that I cannot change that, and that is ok.
But I cannot flash any firmwares now.
I have tried the pre-rooted 4.3 in Odin:
I9505XXUEMK8-PRE-ROOTED-KNOX-FREE-ODEX-FULL
failed.
I have tried official 4.3 for my carrier:
I9505XXUEMJ7_I9505TENEMJ8_I9505XXUEMJ7_HOME.tar
failed.
If I try to flash cwm it boots, but it just stays on the google logo, and does not continue. If I try to enter recovery I get a message about secure mode and it does not enter recovery.
If I flash stock recovery, I can get into recovery. I have tried a factory reset, but it still boots to Google logo and nothing else.
What should I do? There must be a way?
Same issue with me. Looking for solutions. You can install Pacman rom without any problem.
Can someone please give me some pointers?
I have now tried to install the newest firmware from sammobile, even though it isn't for my carrier. It also fails in Odin. I am using 3.07. I can flash CWM and I can get into CWM now, but there's nothing on my sdcard. So I can not flash anything from CWM.
Is it possible to load files onto CWM when the phone won't boot fully?
Is there a firmware I can flash in Odin that will work in this situation?
Should I try Kies? Will Kies be able to sort this out?
Right now I have a brick.
Try a different usb port, different cable, make sure kies is not running in the background and try Odin 1.85.
Make sure you're not mixing up "SDcard" partition on your internal storage with your EXT-SD Card the one that you physically inserted into the device! Save the zip into both maybe and wipe cache, factory wipe, then flash the ROM. Try another cable and USB, try a different recovery e.g. Philz!
RossFixxed said:
Make sure you're not mixing up "SDcard" partition on your internal storage with your EXT-SD Card the one that you physically inserted into the device! Save the zip into both maybe and wipe cache, factory wipe, then flash the ROM. Try another cable and USB, try a different recovery e.g. Philz!
Click to expand...
Click to collapse
During the failed flash-attempts, my sdcard is now empty. I have no files in CWM to flash. How do I get the files to my card? I don't have an external sdcard.
Trying Odin 1.85 now with latest firmware from sammobile. Right now the phone will not boot, I can't flash anything through Odin (due to knox?) and I can't flash anything from CWM since there are no files there to flash...
Edit:
Odin 1.85 also fails. I cannot install any firmware now.
Knox will not stop you flashing with Odin. It won't really affect anything except, potentially, your warranty.
Where have you put the Zip file for the ROM you want to install? You need to point CWM towards it directly, whatever folder it is in... Are you doing that?
You could buy an SD card for a few quid and copy a ROM onto that if needs be... I would flash Philz recovery and Wipe Cache. Wipe factory reset (install a new ROM Option), click Install from SD Card and navigate to the folder.
If your entire SD Partition is wiped you'll need to hook up to the PC and copy the zip back over in download mode.
EDIT: Sorry if this is real obvious or I'm missing what's wrong. I figure if you're anything like me you're a bit anxious about this, just going step by step, we'll fix it!
jadajada said:
Help!
I need some advice. I had stock 4.2.2, flashed omega v14 and then 4.3 GE ROM. I did not know about knox and I have tripped it. It shows 0x1 now. I understand that I cannot change that, and that is ok.
But I cannot flash any firmwares now.
I have tried the pre-rooted 4.3 in Odin:
I9505XXUEMK8-PRE-ROOTED-KNOX-FREE-ODEX-FULL
failed.
I have tried official 4.3 for my carrier:
I9505XXUEMJ7_I9505TENEMJ8_I9505XXUEMJ7_HOME.tar
failed.
If I try to flash cwm it boots, but it just stays on the google logo, and does not continue. If I try to enter recovery I get a message about secure mode and it does not enter recovery.
If I flash stock recovery, I can get into recovery. I have tried a factory reset, but it still boots to Google logo and nothing else.
What should I do? There must be a way?
Click to expand...
Click to collapse
OK so i haven't got an S4 but i do have the mini and have a similar problem.
MJ7 got released but not for my country, so i flashed an AUS MJ7 firmware. Now it has been rolled out to my country and i cannot flash my original FW back due to different CSC. AUS CSC=MJ1 & UK CSC=MK1. (Failed in Odin)
so my theory is i cannot now flash any other regions firmware and stuck with MJ1 CSC. (AUS Firmware)
Can you remember the original FW you flashed when you had knox 0x0?
Hope this makes sense. I'm not getting any replies on S4 mini forum.
*boy*racer* said:
OK so i haven't got an S4 but i do have the mini and have a similar problem.
MJ7 got released but not for my country, so i flashed an AUS MJ7 firmware. Now it has been rolled out to my country and i cannot flash my original FW back due to different CSC. AUS CSC=MJ1 & UK CSC=MK1. (Failed in Odin)
so my theory is i cannot now flash any other regions firmware and stuck with MJ1 CSC.
Can you remember the original FW you flashed when you had knox 0x0?
Hope this makes sense. I'm not getting any replies on S4 mini forum.
Click to expand...
Click to collapse
I most likely had I9505TENEMJ8 or the one before that (MJ5?). It is Norway TEN. I have downloaded the latest for TEN, MJ8 and it fails in Odin. Right now I would be happy just to be able to flash anything at all...
jadajada said:
I most likely had I9505TENEMJ8 or the one before that (MJ5?). It is Norway TEN. I have downloaded the latest for TEN, MJ8 and it fails in Odin. Right now I would be happy just to be able to flash anything at all...
Click to expand...
Click to collapse
OK so in stock recovery does it say your CSC code?
*boy*racer* said:
OK so in stock recovery does it say your CSC code?
Click to expand...
Click to collapse
I had CWM. Tried to flash stock recovery now, but I can't boot into it. I do the usual, then a green android shows up, then shifts to lying on his back with a red exclamation mark over it. Then the phone reboots and stays at the Samsung logo.
I am soon ready to give up. Nothing works!
RossFixxed said:
Knox will not stop you flashing with Odin. It won't really affect anything except, potentially, your warranty.
Where have you put the Zip file for the ROM you want to install? You need to point CWM towards it directly, whatever folder it is in... Are you doing that?
You could buy an SD card for a few quid and copy a ROM onto that if needs be... I would flash Philz recovery and Wipe Cache. Wipe factory reset (install a new ROM Option), click Install from SD Card and navigate to the folder.
If your entire SD Partition is wiped you'll need to hook up to the PC and copy the zip back over in download mode.
EDIT: Sorry if this is real obvious or I'm missing what's wrong. I figure if you're anything like me you're a bit anxious about this, just going step by step, we'll fix it!
Click to expand...
Click to collapse
How do I copy a file over through download mode?
I have tried adb shell with CWM booted, but I get "unauthorized device error"
I think I will buy an sdcard, but that won't solve my problem with not being able to flash anything with Odin. But perhaps I can get a working rom flashed through CWM.
I had no problems flashing roms with odin before knox. Now I can not flash anything at all.
Edit:
I have also tried connecting to kies now like this:
http://androidcentral.us/2013/09/how-to-fix-firmware-upgrade-encountered-an-issue-on-kies/
I get a message saying model GT-I9505 does not support initialization.
So?
jadajada said:
How do I copy a file over through download mode?
I have tried adb shell with CWM booted, but I get "unauthorized device error"
I think I will buy an sdcard, but that won't solve my problem with not being able to flash anything with Odin. But perhaps I can get a working rom flashed through CWM.
I had no problems flashing roms with odin before knox. Now I can not flash anything at all.
Edit:
I have also tried connecting to kies now like this:
http://androidcentral.us/2013/09/how-to-fix-firmware-upgrade-encountered-an-issue-on-kies/
I get a message saying model GT-I9505 does not support initialization.
So?
Click to expand...
Click to collapse
Boot it into download mode and copy the zip over with windows explorer, into the internal memory. Navigate with Install from Zip option in CWM (maybe try Philz, it definitely works for me, with Knox 0x1) and install.
RossFixxed said:
Boot it into download mode and copy the zip over with windows explorer, into the internal memory. Navigate with Install from Zip option in CWM (maybe try Philz, it definitely works for me, with Knox 0x1) and install.
Click to expand...
Click to collapse
When the phone is in download mode, where do I find it in Windows? It does not show in Windows Explorer, but it shows up in Odin.
jadajada said:
When the phone is in download mode, where do I find it in Windows? It does not show in Windows Explorer, but it shows up in Odin.
Click to expand...
Click to collapse
RossFixxed said:
Boot it into download mode and copy the zip over with windows explorer, into the internal memory. Navigate with Install from Zip option in CWM (maybe try Philz, it definitely works for me, with Knox 0x1) and install.
Click to expand...
Click to collapse
OK. I went out and got an sd card. Copied over a rom zip to the card, flashed CWM and rebooted into recovery. Chose install from external sd card and ran the file. The setup started and ran for a few seconds, then the phone rebooted and I am back on the Samsung Logo.
I just can't flash any firmwares on this phone no matter how. Knox or not, but it all started when I tried to reflash stock rom using odin after the knox flag was triggered.
Any more ideas?
Edit:
just tried Philz recovery also. Same thing. Update runs for a few seconds then reboot. No go.
Edit 2:
Philz has the option to clean for installing a new rom. It also fails with this:
E:format_volume: make_extf4fs failed on /dev/block/mmcblk0p27
I suppose this as something to do with nothing being able to flash here. What Can be done with this?
Edit 3:
Success!! I was able to flash Omega Rom V14 through Philz. I actually installed and is running. I do get two knox lines at boot, one yellow and one red, something about the kernel not being something...
Now to investigate what the h*ll happened.
I am still unable to install any firmware through Odin. Going to try the Google Edition 4.3 again since I kind of liked that. But what actually happened here?
I'm happy to hear you got it working! I have no idea what caused it, first thought is corrupted zip files for rom. I'll have a look into it.
Sorry didn't get back to you, fell and injured my back, had to go get injections!
Sent from my GT-I9505 using xda app-developers app
jadajada said:
Can someone please give me some pointers?
I have now tried to install the newest firmware from sammobile, even though it isn't for my carrier. It also fails in Odin. I am using 3.07. I can flash CWM and I can get into CWM now, but there's nothing on my sdcard. So I can not flash anything from CWM.
Is it possible to load files onto CWM when the phone won't boot fully?
Is there a firmware I can flash in Odin that will work in this situation?
Should I try Kies? Will Kies be able to sort this out?
Right now I have a brick.
Click to expand...
Click to collapse
Mj7 is not a 4.3 rom. Have you tried to flash any stock 4.3 rom (for example ubuemk1 fob latam) or any other you are sur to be 4.3? Samsung alerted clearly before updating to 4.3 you won't be able to back prior versions any more...
Enviado desde mi GT-P7510 usando Tapatalk 2
jaswinky said:
Mj7 is not a 4.3 rom. Have you tried to flash any stock 4.3 rom (for example ubuemk1 fob latam) or any other you are sur to be 4.3? Samsung alerted clearly before updating to 4.3 you won't be able to back prior versions any more...
Enviado desde mi GT-P7510 usando Tapatalk 2
Click to expand...
Click to collapse
Solved! I do not know what solved it. I managed to install Omega Rom V16 through Philz recovery. From there I rebooted into Philz again and did a total clean to install new rom.
I downloaded a newer Odin, 3.09.
I flashed the same firmware which failed yesterday, 4.3 NEE rom.
This time it worked! So something helped.
Thank you to everyone who chipped in. It seemed rather hopeless yesterday.
I know the feeling man but is possible you were downgrading and you can't do that with knox now.
Sent from my GT-I9505 using xda app-developers app
jadajada said:
Can someone please give me some pointers?
I have now tried to install the newest firmware from sammobile, even though it isn't for my carrier. It also fails in Odin. I am using 3.07. I can flash CWM and I can get into CWM now, but there's nothing on my sdcard. So I can not flash anything from CWM.
Is it possible to load files onto CWM when the phone won't boot fully?
Is there a firmware I can flash in Odin that will work in this situation?
Should I try Kies? Will Kies be able to sort this out?
Right now I have a brick.
Click to expand...
Click to collapse
You can try flashing TWRP it support usb mount on recovery then transfer OMega Rom again..
Kies wont work on your phone because your already in the custom status.
Hello all!
First off I would just like to say thank you, thank you, thank you. I have been a long time lurker on these forums (since the evo) and have gotten a lot of useful information from here. Now to my issue. I have had no phone for two weeks now, and have been doing search after search. I upgraded my phone to 4.3 (it was mk2) and rooted it via motochopper. So my dumbass tried to flash a custom rom with kn0x0ut and it failed. The phone rebooted and now will boot up to the samsung custom screen. You can hear the att boot up sound but no image. I can get into odin mode and stock recovery. When I am in odin it says:
ODIN MODE
PRODUCT NAME: SGH-I337
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMC BURST MODE enabled
I have tried sideloading the stock MJ9 and MK2 files to no avail. I really hope somebody can help me, I don't know how much longer i can go without a phone. Thanks guys and Merry Christmas!!!
yea sounds like bricked you cant flash roms on 4.3 yet take it to best buy that has a samsung center and just tell them samsung sent you here because my phone all of a sudden was acting up and they will flash it back to factory for you thats what i had to do
gtj0 said:
OK, If you're stuck with an incomplete flash, here are some steps you can try to get to MJ9...
These instructions assume you started with MJ6.
First, make sure you can boot into recovery. If not, download and apply the MJ6 recovery.
recovery-mj6.tar.md5
It should apply without error. If not, report the failure.
Download and extract the following files...
mf3-emergency-part-1.tar.md5.7z
mf3-emergency-part-2.tar.md5.7z
If you don't already have it, download the mf3-mj9 update file...
update-mf3-mj9.zip
Start Odin, connect your phone and boot into Download mode.
Flash mf3-emergency-part-1.tar.md5 which contains modem.bin, NON-HLOS.bin and system.img.ext4.
The flash of system.img.ext4 WILL FAIL at the end. That's OK.
Reboot the phone back into Download mode and restart Odin.
Flash mf3-emergency-part-2.tar.md5 which contains cache.img.ext4.
The flash WILL FAIL at the end. That's OK.
The phone should now reboot to recovery by itself and apply a small update. If it fails, stop and report.
The phone should now reboot to a black screen with the pulsing notification LED.
Reboot into recovery mode and flash update-mf3-mj9.zip. I recommend sideloading instead of flashing from sdcard because the sdcard method reboots the phone whether the update was successful or not and you lose the error messages.
Reboot the phone and let it initialize.
You should now have MJ9.
Click to expand...
Click to collapse
download the above files except update-mf3-mj9.zip and replace with MF3>MK2 from this thread
http://forum.xda-developers.com/showthread.php?t=2573080
Hashcode has a Beta safesatrap for MK2 Safestrap-JFLTEATT-3.70-B01 if you want to flash anything to a rom slot or stock slot and make a backup (does not work with EXFAT formatted sd yet)
http://forum.xda-developers.com/showthread.php?t=2448925
dolph8886 said:
download the above files except update-mf3-mj9.zip and replace with MF3>MK2 from this thread
http://forum.xda-developers.com/showthread.php?t=2573080
Hashcode has a Beta safesatrap for MK2 Safestrap-JFLTEATT-3.70-B01 if you want to flash anything to a rom slot or stock slot and make a backup (does not work with EXFAT formatted sd yet)
http://forum.xda-developers.com/showthread.php?t=2448925
Click to expand...
Click to collapse
I was on MK2 using the 3.7 beta of SS when I couldn't get it to boot anymore. Tried the modified method outlined above, everything worked except after step 7, it never rebooted to recovery on it's own and installed a small update. Decided to try Kies, says it can do emergency firmware recovery but it hasn't worked yet. Any help would be appreciated as I'm not sure I can get the handset replaced since I got it at Walmart.
It may not automatically reboot into recovery, just make it.
if you do not already know this (i am not saying you don't)
holding the power button for 10? seconds will reboot phone or using the file in post below
http://forum.xda-developers.com/showpost.php?p=48621760&postcount=18
hold volume up and power the phone on to boot into stock recovery
have android sdk and files above ready
choose option to sideload update from adb
open terminal on computer and
adb sideload "update.zip"
without quotes
here are basically the same instructions just a bit different
sl1200md3 said:
Back on AT&T STOCK MK2 from a bricked TWRP'd install. I had to do the following:
1) Phone into download mode
2) Flash mf3-emergency-part-1.tar.md5 via Odin v1.85
3) Force Reboot
4) Flash mf3-emergency-part-2.tar.md5
5) Unplug phone / Reset Odin / plug phone back in
6) Flash recovery-mj6.tar.md5
7) Force Reboot in Odin using this file http://forum.xda-developers.com/showthread.php?t=1766399 Thanks kevinpc :good:
8) Manually enter recovery
9) ADB Sideload the file: update-mf3-mj9.zip found here: http://forum.xda-developers.com/showpost.php?p=47604388&postcount=152
10) ADB Sideload the file: update-MJ9-MK2.zip found here: https://docs.google.com/file/d/0B2iXrnZBB-MVYkYwNkYzU2FJaFk/edit
11) Reboot
Won't be flashing TWRP via Goo Manager again any time soon.
:good::good::good:
Click to expand...
Click to collapse
dolph8886 said:
It may not automatically reboot into recovery, just make it.
if you do not already know this (i am not saying you don't)
holding the power button for 10? seconds will reboot phone or using the file in post below
http://forum.xda-developers.com/showpost.php?p=48621760&postcount=18
hold volume up and power the phone on to boot into stock recovery
have android sdk and files above ready
choose option to sideload update from adb
open terminal on computer and
adb sideload "update.zip"
without quotes
here are basically the same instructions just a bit different
Click to expand...
Click to collapse
You sir, are amazing. What you posted was just different enough from what I had previously tried to work. I'm now booting and on MK2, thanks a million man!
FINALLY
dolph8886 said:
download the above files except update-mf3-mj9.zip and replace with MF3>MK2 from this thread
http://forum.xda-developers.com/showthread.php?t=2573080
Hashcode has a Beta safesatrap for MK2 Safestrap-JFLTEATT-3.70-B01 if you want to flash anything to a rom slot or stock slot and make a backup (does not work with EXFAT formatted sd yet)
http://forum.xda-developers.com/showthread.php?t=2448925
Click to expand...
Click to collapse
FINALLY LONG SEARCH OVER FOR THIS FIX JUST ONE QUESTION WILL THE RECOVERY FAIL AS WELL?
tonyc0642 said:
You sir, are amazing. What you posted was just different enough from what I had previously tried to work. I'm now booting and on MK2, thanks a million man!
Click to expand...
Click to collapse
hi i have the exact same problem....i dont know how to start adb on windows 7...arrgh...
Thanks to the everyone for this
It saved my ass..I put the zips on a sd and installed.Back on mk2 and rooted.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
I tried the above mentioned but after I flash the second file and reboot, it goes into kies , no recovery mode. Odin is still available. Also thanks for all the quick responses fellas yall are the best.
***UPDATE*** flashed the recovery but the sideload failed. Tried to turn it on and the Samsung lolgo came on, then went black. After a a few minutes the phone pops up on the computer and I can access the internal phone memory and the sd card.
I am really not sure, I believe that it will work if you do this process again.
No Idea if this makes any difference but, pay close attention to the process at least until the sideloading of the update.
Do not let the device attempt to boot with this firmware mismatch as this may cause issues. (This is the only conclusion I can come to as this process does work)
If the device automatically reboots then press and hold volume up to enter recovery or volume down to enter download mode.
If manual reboot or powering on then press and hold volume up or down respectively then press power until the device starts and release power button to avoid a reset.
SOLVED!!!
Thank you so much @dolph8886!!!1 You are the BEST!!! :good: :victory: :highfive:
This helped me, fixed my softbrick, hope this helps! Remember to thank the author if it works
http://forum.xda-developers.com/showthread.php?t=2621279
ok here it goes i tried to flash twrp using goo but now i have no stock recovery can someone help me please im on mk2 running 4.3 and rooted
So I've been running a rooted Note 3 for a while. When the Note 3 Kitkat update came out, I updated it via Odin as OTA update was not available since I was rooted.
All the posts I read had mentioned that updating to 4.4.2 from 4.3 would erase all my data but after updating via odin all my data was in place. I had only lost root which I rooted again though CF Auto Root.
The problem now is that when I try to install CWM (via Odin) or TWRP (via Goo or Odin), it goes through the installation but then the phone goes into a boot loop of sorts..It's NOT the normal boot loop which gets stuck on the Samsung logo.
What happens is that the phone vibrates twice (with a 1 sec interval in between), then the Samsung Note 3 N-9005 screen appears with "Booting Recovery..." on the top left and within a sec it goes blank and then back to 2 vibrates and the screen come on to show Samsung Note 3 N-9005.
The only way I found to fix this was a battery pull and then turning on the device holding the power, home and down vol key to boot into recovery and then flashing CF Auto Root again.
I don't know why am I not able to install any of these recoveries. I've made sure I try to install the latest versions of them which are Kitkat compatible.
Anyone else with this problem or a solution?
Can a Cache and data wipe fix this? But the problem again being I won't be able to backup my ROM since i can't get these recoveries to install!
There is a script in official firmware that checks for official recovery and if it finds a custom one it tries to overwrite with official one. If i remember correct it's called install-recovery. sh
PhilZ recovery handles it automatically.
It's impossibe to flash anything other than the leaked 4.4.2 stock because you flashed your bootloader to kitkat, no you MUST stay on sammy 4.4.2 till the devs found a solution for this. Thats why you have to read carefully be4 you flash.
silentvisitor said:
There is a script in official firmware that checks for official recovery and if it finds a custom one it tries to overwrite with official one. If i remember correct it's called install-recovery. sh
PhilZ recovery handles it automatically.
Click to expand...
Click to collapse
No luck!
I tried PhilZ recovery from the below link.
http://goo.im/devs/philz_touch/CWM_Advanced_Edition/hltexx
What are my other options?
sid8907 said:
No luck!
I tried PhilZ recovery from the below link.
http://goo.im/devs/philz_touch/CWM_Advanced_Edition/hltexx
What are my other options?
Click to expand...
Click to collapse
This one seems to be the only one working with 4.4.2 right now.
Possible solution
The way I can suggest is to create a little update.zip file with little updater-script to remove install-recovery.sh file from device (just one line needed).
Ok, I found a zip which I am attaching below. You(or anyone) may review the script before flashing.
Place this on your external (or internal) sdcard.
In ODIN don't check Auto reboot
Flash Recovery. Remove phone when it says PASS.
Remove battery. Start in Recovery mode by pressing buttons.
You should now be in new Recovery.
Flash that zip file.
Reboot.
You should be good.
The Auto Reboot for some reason is faded out. Tried different versions of Odin and also tried to open it with the phone connected/disconnected.
I am out of ideas.
I would suggest you to wait for someone to come up with working solution. Being too adventurous with ODIN could brick your device.
sid8907 said:
The Auto Reboot for some reason is faded out. Tried different versions of Odin and also tried to open it with the phone connected/disconnected.
Click to expand...
Click to collapse
Clear out all your ODIN caches etc, delete all files and keep 1.85.
Flash this (only working recovery on 4.4.2) via PDA in ODIN, If it doesn't reboot auto after saying PASS or RESET.. just turn phone off, reboot into recovery and it'll be fine.
EDIT: Just re-read, Re flash your Stock 4.4.2 (Use XEO not the leaked one!) and then start again
Thanks!
Maybe a little off topic, but is there a way to install CM11 on Stock 4.4.2 on the Note 3?
I've been reading Samsung is out with a new bootloader so there is no way round this?
radicalisto said:
Clear out all your ODIN caches etc, delete all files and keep 1.85.
Flash this (only working recovery on 4.4.2) via PDA in ODIN, If it doesn't reboot auto after saying PASS or RESET.. just turn phone off, reboot into recovery and it'll be fine.
EDIT: Just re-read, Re flash your Stock 4.4.2 (Use XEO not the leaked one!) and then start again
Click to expand...
Click to collapse
Thanks!!
sid8907 said:
Thanks!
Maybe a little off topic, but is there a way to install CM11 on Stock 4.4.2 on the Note 3?
I've been reading Samsung is out with a new bootloader so there is no way round this?
Click to expand...
Click to collapse
You may have to do a little reading but I believe CM11 is now working on the KK bootloader...
sid8907 said:
So I've been running a rooted Note 3 for a while. When the Note 3 Kitkat update came out, I updated it via Odin as OTA update was not available since I was rooted.
All the posts I read had mentioned that updating to 4.4.2 from 4.3 would erase all my data but after updating via odin all my data was in place. I had only lost root which I rooted again though CF Auto Root.
The problem now is that when I try to install CWM (via Odin) or TWRP (via Goo or Odin), it goes through the installation but then the phone goes into a boot loop of sorts..It's NOT the normal boot loop which gets stuck on the Samsung logo.
What happens is that the phone vibrates twice (with a 1 sec interval in between), then the Samsung Note 3 N-9005 screen appears with "Booting Recovery..." on the top left and within a sec it goes blank and then back to 2 vibrates and the screen come on to show Samsung Note 3 N-9005.
The only way I found to fix this was a battery pull and then turning on the device holding the power, home and down vol key to boot into recovery and then flashing CF Auto Root again.
I don't know why am I not able to install any of these recoveries. I've made sure I try to install the latest versions of them which are Kitkat compatible.
Anyone else with this problem or a solution?
Can a Cache and data wipe fix this? But the problem again being I won't be able to backup my ROM since i can't get these recoveries to install!
Click to expand...
Click to collapse
here's the link for twrp for ya'll http://forum.xda-developers.com/showpost.php?p=50333147&postcount=398
sid8907 said:
So I've been running a rooted Note 3 for a while. When the Note 3 Kitkat update came out, I updated it via Odin as OTA update was not available since I was rooted.
All the posts I read had mentioned that updating to 4.4.2 from 4.3 would erase all my data but after updating via odin all my data was in place. I had only lost root which I rooted again though CF Auto Root.
The problem now is that when I try to install CWM (via Odin) or TWRP (via Goo or Odin), it goes through the installation but then the phone goes into a boot loop of sorts..It's NOT the normal boot loop which gets stuck on the Samsung logo.
What happens is that the phone vibrates twice (with a 1 sec interval in between), then the Samsung Note 3 N-9005 screen appears with "Booting Recovery..." on the top left and within a sec it goes blank and then back to 2 vibrates and the screen come on to show Samsung Note 3 N-9005.
The only way I found to fix this was a battery pull and then turning on the device holding the power, home and down vol key to boot into recovery and then flashing CF Auto Root again.
I don't know why am I not able to install any of these recoveries. I've made sure I try to install the latest versions of them which are Kitkat compatible.
Anyone else with this problem or a solution?
Can a Cache and data wipe fix this? But the problem again being I won't be able to backup my ROM since i can't get these recoveries to install!
Click to expand...
Click to collapse
jp.26 said:
here's the link for twrp for ya'll http://forum.xda-developers.com/showpost.php?p=50333147&postcount=398
Click to expand...
Click to collapse
so.... yeah i just updated my bootloader to 4.4.2 and this drove me literally insane. ive been working on it for 4 hours now. i encountered so many problems with installing the bootloader. exact same problem as SID8907. i gotta tell you tho.... you worked some magic my friend. i tried almost everything. then i came across your link. i was like why not? so i flashed the img in odin..... anddddd :drumroll pleaseeeeee:: IT WORKED. ahhh....... so much frustration and the problem is solved!!! thank you so much JP.26 :good::laugh:
is there any word on how to fix this been looking for hours tmobile note beast dont want to put any roots down on my phone before i find a way to flash cm or a non bloated note rom would be nice.
I'll that I've managed is to root and flash twrp I found a way to turn cwm recovery into a tar file and flash through odin. But i just get into a boot loop with cwm due to the boot loader I presume but tarp works fine I just can't flash cm11. I get boot loop every time
Sent from my SM-N900T using XDA Premium 4 mobile app
im sorry but im confused here... does this all simply mean that there is not yet a working cwm for 4.4.2 yet? and that while we can root, there is no working recovery for this version?
I'm not sure myself tarp works but I can't flash cm11
Sent from my SM-N900T using Tapatalk
Phillz cwm Dev edition I think that's the name works its a themed touch cwm. This works great but still can't flash cm so gayyyy
Sent from my SM-N900T using Tapatalk
I was wondering what happened to the cmw too.
The modded cmw by Chenglu is the only one working that I know of.
Link to thread: http://forum.xda-developers.com/showthread.php?t=2454079
i installed safe strap and got gold finger rom working now im locked out when i try to boot in recovery it says firmware upgrade encountered an issue. please select recovery mode in kies and try again i have download mode no recovery what can i do to fix stock recovery for samsung galaxy s4 can it be fixed i tried flashing with odin the stock recovery that fixed it last time it fails when it get to the last boot check
There is no real use for the stock recovery. What are you really trying to achieve?
jmjoyas said:
There is no real use for the stock recovery. What are you really trying to achieve?
Click to expand...
Click to collapse
i installed safe strap and sucessfully installed gold finger but installed *root* recovery tools app in playstore and flashed over twrp well that locked my original recovery and has messed everything up where i cant load anything but download mode rom is not working just download mode =,(
update i reflash the sgh-i337 .pit file and gain access to stock recovery but when i try to flash another stock rom fails and i have to reflash the .pit file when it loads up it shows a att logo that goes to a weird image and freezes is it hard bricked
update
fixed the phone slot was clicked and not pda thanks for the help i figured it out and im glad i did omg i was almost in tears =)) awsome work xda
You needed the pit file because of the re-partition option ticked in Odin.