Hey Guys, i'm trying to install the new JB MIUI Rom on my HD2 but i fail each time. I used Task29, reinstalled MGLDR and set the partition size to 350/5. Then i just flashed the ROM with NAND after having data factory reset my phone and wiping the cache / dalvik cache.
But now i get the bootanimation but nothing more.
And my second question, how would i get the language to german. I'm a bit confused with the language packs and different downloads.
Thanks in advance!
Related
Hello everyone
I have a big problem trying to solve a long time but I must admit that I give up
I tried to install nearly all versions of Android but after about 10 minutes I get stuck and have to remove the battery. On reboot it gives me nand faild to boot of nand and have to reinstall again
I have T-Mobile USA
Thanks
Please excuse me for my English
How are you Flashing your build? DAF or ZIP?
If ZIP, Try wiping everything before installing new build (Cache, data, and dalvik cache (it's in the advanced tab))
If that doesn't work, Task 29 -> MAGLDR -> Either CWM or DAF Android.
If you had this problem, than start from "0".
That means, format your sd-card and task29.
Good luck
Thanks for the replies.
I tried everything, including the original ROM installation, from t-mobile and everything hangs on restart
Hi there,
I wanna try the Tytung's rom NEXUS-HD2 ICS rom but It won't start. Install looks to be ok, nothing special happens, but when I reboot the phone, I only got "HTC" in green letters on my HD2 screen. Anyone got any idea about this problem?
Thank you for your help.
Hello
to get useful help, please explain what you exactly did.
I put the rom on my sd card, then I used HD2 Android Nand toolkit to repartition the phone : system 200MB, Cache size 45MB.
I reboot the phone, use the ad recovery to install zip from SD card. The install performs with no problem, with the "install complete" message at the end. I reboot the phone, it turns on, and then nothing happens, just the HTC logo on the screen. I can wait several minutes, nothing else happens.
45 MB cache size? Tytung recommends 2MB and I think is enough. Did you wipe everything (factory reset, cache, Dalvik cache) in recovery before install rom?
Hi
Most responses in the Main thread "stuck on HTC Logo" say that the system partition is too small. If there are any bad blocks in NAND can not reach 200MB.
I use ClockworkMod 5.0.2.7 with 250M system and 10M cach partition and have no problems except the known issues, that descriped in the first post.
Before i have installed the rom, i flashed HSPL2.08, Radio 2.15.50.40, Magldr 1.13.
Try wiping Nand and reflash
Hi Guys,
Currently i am running MIUI 2.4.20 GB 2.3.7 + ICS Multilanguage on my miletone 2 and i have tried to upgrade the ROM with Cynogen9 however nothing is happening. It's going through the process but after a reboot it is just booting back into MIUI.
Here are the steps i took (please note i tried both EU and CH based ROMS)
1) downloaded O.S and placed on SD Card
2) booted into recovery (CWM)
3) performed wipe cache partition
4) performed wipe data/factory reset
5 install zip from sd card and installed cynogen9
after this though nothing happens and it just boots back into MIUI. I tried several times with both EU and CH version and no luck.
I also even tried installing from sd card first then performing the cache wipe and data wipe and still no luck.
Any help on this would be greatly appreciated. I tried lookin for some instructions on this however couldnt find anything.
Thanks
jawgeeb said:
Hi Guys,
Currently i am running MIUI 2.4.20 GB 2.3.7 + ICS Multilanguage on my miletone 2 and i have tried to upgrade the ROM with Cynogen9 however nothing is happening. It's going through the process but after a reboot it is just booting back into MIUI.
Here are the steps i took (please note i tried both EU and CH based ROMS)
1) downloaded O.S and placed on SD Card
2) booted into recovery (CWM)
3) performed wipe cache partition
4) performed wipe data/factory reset
5 install zip from sd card and installed cynogen9
after this though nothing happens and it just boots back into MIUI. I tried several times with both EU and CH version and no luck.
I also even tried installing from sd card first then performing the cache wipe and data wipe and still no luck.
Any help on this would be greatly appreciated. I tried lookin for some instructions on this however couldnt find anything.
Thanks
Click to expand...
Click to collapse
Try to boot into Recovery with the Reboot Menu of MIUI.
Hold the Power button -> Reboot -> Recovery and try to install the rom again.
Hello to all!
I was flashed stock firmware yesterday ( I had a custom ROMs before) and it runs pretty good, but I have one annoying thing: when I power on my phone it boot to bootloader straight instead system( I should to press START to load system every time. Who know how to solve this problem??? Very need help.
XT1562 - 1 sim - europe, android 6.0.1 - stock
That may be because the system was flashed over the custom rom system.
What I do when I go from a custom ROM to stock is I use TWRP to wipe Dalvik / ART Cache, Cache, Data, Internal Storage and System. Then I flash the stock ROM.
***Problem Solved***
Hello All,
First of all, Iam a newbie in custom roms so i hope it's not a stupid question...
Couple of months ago i rooted my LG G2 en installed TWRP and after that i flashed Lineageos 14.1.
But i wanna try something else.
I flashed AOSP and works like a charm.
So i decided to flash another one.
But now my phone is stuck on a TWRP loop.
I aleady update twrp to a new version: 3.2.1.0 but it still not work.
What did i do:
Iam going to wipe.
Advanced wipe and wipe:
Dalvik/ART cache
System
Data
And cache
After that iam going to Install:
select the rom and the OpenGapps. (ARM 7.1 Nano)
And confirm flash.
After the flash i wipe Cache and Dalvik and then reboot..
But it's only starting in recovery again and again.
I have tried this roms:
Lineageos
ASOP
CRdroid
Paranoid Android
MK
Ressurection remix
But none of the roms will work
I also tried to wipe Internal storage but unfortunatly that also doesnt work
What iam doing wrong?
Or what can i do to get one of this roms to work?
Thank you
***Problem Solved***
I Found it!!
By Terminal i have to type a code and then another code.
My phone is working again.