Database Users

Defy Bricked no bootloader

I tried to flash a custom rom to a defy, but after flashing i got a bootloop.. After that i have tried everything to get a normal working installation but everything failed.
Now i am stuck with a phone that does not want to boot and even cannot get into the bootloader... So i cannot flash using RSD Lite.
Is there another way to unbrick this phone? Or is it end of story?

can you enter on CWM??
Sent from my MB526 using XDA App

1) Remove battery
2) Plug phone to PC
3) launch rsdlite (make sure rsdlite driver's is already working properly)
4) Press power and vol+ , and insert battery.
5) Defy screen might still blank but rsdlite would show status connected.
6) flash back your default sbf
7) boot into stock recovery and do factory reset.
8) reboot.
Note: if your defy is in full flash over gingerbread sbf, you're in trouble. Flash again any gingerbread sbf might help for quick resurrection. If your defy is in froyo, try flashing only froyo, otherwise if you're desperate, gingerbread sbf would help. You're warned for no possibility of downgrade.
Note 2: Battery must at least 80% and above to safely flashing and recovering process.

farsight73 said:
1) Remove battery
2) Plug phone to PC
3) launch rsdlite (make sure rsdlite driver's is already working properly)
4) Press power and vol+ , and insert battery.
5) Defy screen might still blank but rsdlite would show status connected.
6) flash back your default sbf
7) boot into stock recovery and do factory reset.
8) reboot.
Note: if your defy is in full flash over gingerbread sbf, you're in trouble. Flash again any gingerbread sbf might help for quick resurrection. If your defy is in froyo, try flashing only froyo, otherwise if you're desperate, gingerbread sbf would help. You're warned for no possibility of downgrade.
Note 2: Battery must at least 80% and above to safely flashing and recovering process.
Click to expand...
Click to collapse
Tried this, but with no effect.

klompie said:
I tried to flash a custom rom to a defy, but after flashing i got a bootloop.. After that i have tried everything to get a normal working installation but everything failed.
Now i am stuck with a phone that does not want to boot and even cannot get into the bootloader... So i cannot flash using RSD Lite.
Is there another way to unbrick this phone? Or is it end of story?
Click to expand...
Click to collapse
What file did you flash??

gommers1978 said:
What file did you flash??
Click to expand...
Click to collapse
I made a nandroid backup first. Then i tried to install MIUI rom and that did not boot. Tried to restore my nandroid backup, but it did not work. After that i have tried to flash a lot of sbf files but all did not work correclty. Also putting back my nandroid backup was not working.

Your battery is fully loaded?
What happens when you plug in the loader (powercord with adapter in AC plug) when phone is off, is there a battery loading icon appearing?

gommers1978 said:
Your battery is fully loaded?
What happens when you plug in the loader (powercord with adapter in AC plug) when phone is off, is there a battery loading icon appearing?
Click to expand...
Click to collapse
Nothing happens.. not even the power led turns on.
The last time i flashed it was almost fully loaded.

klompie said:
Nothing happens.. not even the power led turns on.
The last time i flashed it was almost fully loaded.
Click to expand...
Click to collapse
When you turn it on the screen stays black or does the M logo appear?

gommers1978 said:
When you turn it on the screen stays black or does the M logo appear?
Click to expand...
Click to collapse
When i "turn it on" it stays black

klompie said:
When i "turn it on" it stays black
Click to expand...
Click to collapse
If there is no white led or anything im afraind you have to send it for repair.
In the Netherlands i have a very good experience with:
http://www.gsmrepareren.nl/eindgebruiker/
Last thing you can try is to turn the phone on with vol down but i think you have allready tried that.

gommers1978 said:
Your battery is fully loaded?
What happens when you plug in the loader (powercord with adapter in AC plug) when phone is off, is there a battery loading icon appearing?
Click to expand...
Click to collapse
I have the same problem. I come from 2ndinit cm10 and wanted to revert back to cm7.2 but my defy failed to boot. After that I flashed FIXED.French.3.4.2-164.RETAIL.sbf
I hoped that might flash the kernel (home, back buttons were dark due to cm10). I got the red M back and a bootloop.
So I tried some sbf's I had on my hdd. Now the battery is at 3,3v and rsd lite doesn't get the phone. When I apply 5v (like the McGyver hack) the voltage drops to about 4v because the battery is being charged (dangerously I know).
Anyway rsd lite sees my defy again, I am able to flash. But when it should reboot, rsd sais PASS and the screen stays dark.
Connecting usb causes the charging led go on.
How can I bring the device back to life?
Thanks
Dennis

Hi, hold vol down and power, then make a factory reset.
Sent from my MB526

That doesn't work. The screen stays black except I flash a sbf with externally powered battery.
I am not able to see the bootloader or recovery.
Sent from my Nexus 4 using xda app-developers app

I had this problem, try different sbf's. The first 2-3 that I tried which gave me a blank screen were too old (from 2010) and the last one was from 2011 which was successful. Try with sbf from 2011.

Do you still know what sbf's you have tried and which one did it's job?
Thank's for your answer though!
Edit:
I tried the following one without success
JRDNEM_U3_2.21.0_SIGNED_UCAJRDNEMARAB1B80AA028.0R_USAJORDANRTDACH_P017_A003_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_164-003_VFBLUR_SIGN_SIGNED_USAJRDNEMARAB1B8VFFR03A.0R_PDS03C_USAJRDNFRYOVFFR_P028_A014_M004_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_177-003_BLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTDACH_P014_A009_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_UCAJRDNFRYORTCOREEU_P023_A008_HWp3_Service1FF.sbf

i had same case, blank screen.
even no bootloader text.
with charger i got white led.
then connected it to pc and RSD found it,
then flashed with this instruction:
there is some kind special fixed SBF on the link
[GUIDE] All-in-One Defy Beginner's guide
Method 2: (BIG thanks to Jebrew again for this one)
NOTE: You are going to need CM7 for this one. CM7 Stable version recommended.
Download this SBF and Flash it.
Root your phone.
Download 2nd Init 1.4.2 and Install ClockworkMod Recovery.
Reboot to CMW recovery, and wipe Data/Cache.
Install CM7 then install Google Apps.
Reboot an go into Stock Recovery (using the vol- button, not from Bootmenu).
Do a Data/Cache Wipe or you won't have any space when you're done.
Flash this Fixed SBF
Reboot into your nice new rom.
Do not Wipe Data anymore or you will have to start again.
You WONT be able to install full SBFs of any Éclair or Froyo since these Androids have lower CG Versions.
http://forum.xda-developers.com/showthread.php?t=1216982
Click to expand...
Click to collapse

Thanks!
But nothing changes. RSDLite still sais: Finished and PASS

shyd said:
Anyway rsd lite sees my defy again, I am able to flash. But when it should reboot, rsd sais PASS and the screen stays dark.
Connecting usb causes the charging led go on.
Click to expand...
Click to collapse
Did you try also this special fixed JORDN_U3_97.21.51.sbf from this guide ?
battery should not be low, otherwise RSD would not connect.
but if, then MacGyver power supply trick.

Yes, I took this sbf. Battery is ok. RSD lite is able to flash.
But when the phone should reboot, the screen stays black and the phone connects to RSD lite saying finished, pass.

Strange Bricked Defy ?

Hi all,
I have a friend's Defy from a French carrier and my friend is with another carrier so I decide to SIM unlock it by installing CM7 and other files.
So I have root it and install the recovery.
In recovery, I have flash CM7 and Gapps.
But I get a boot loop...
So I decided to flash JORDN_U3_97.21.51 SBF and restart from scratch.
But now, the phone wont boot at all.
Nothing on the screen but it's still reconized by RSD (even if nothing is displayed on the screen) I can re-flash SBF files and RSD say "PASS" but doesn't reboot the phone.
So now I have a brick and can't boot vol up + power doesn't display anything.
Dose anyone have an idea for me ?
Thank you.

1st don't loose your battery - when no working system on the device then it is not being charged
You wrote nothing about wipes - have u performed them? If not try to get into any recovery and wipe user data / factory reset, try vol- w/power or vol + & - together, take a battery for some time before doing it etc.
What ROM u had before flashing CM7?
Is it defy or defy+?
And you flashed CG5 sbf
When you give more details maybe I can propose proper solution.

You wrote nothing about wipes - have u performed them? If not try to get into any recovery and wipe user data / factory reset, try vol- w/power or vol + & - together, take a battery for some time before doing it etc.
Click to expand...
Click to collapse
If I understood right, OP's DEFY is completely bricked and he cannot even access recovery.
Anyway, I unfortunately no solution to propose as I have a DEFY in the same situtation and I'm currently unable to revive it. We aren't the only who had DEFY bricked like this and some managed to have it wake up by flashing certain sbf.
You can try searching "bricked defy" on XDA and see what sbf the topic creator used to save his DEFY, if he succeeded to.

dont flash sbf just after the bootloop..!
-JFK- said:
Hi all,
I have a friend's Defy from a French carrier and my friend is with another carrier so I decide to SIM unlock it by installing CM7 and other files.
So I have root it and install the recovery.
In recovery, I have flash CM7 and Gapps.
But I get a boot loop...
So I decided to flash JORDN_U3_97.21.51 SBF and restart from scratch.
But now, the phone wont boot at all.
Nothing on the screen but it's still reconized by RSD (even if nothing is displayed on the screen) I can re-flash SBF files and RSD say "PASS" but doesn't reboot the phone.
So now I have a brick and can't boot vol up + power doesn't display anything.
Dose anyone have an idea for me ?
Thank you.
Click to expand...
Click to collapse
frend i wanna tell u onething.the very first time i did the flashing of cm7.1stable on froyo 2.2.2defy i got a bootloop..since i was in hostel i cudnt afford internet..so i was soo scared and even waited for 15 min..but the cm7 logo with an arrow swirling around didnt stop..i puld the batery out and again inserted and did something stupid like clearing data and got the condition worse
then i flashed sbf using rsd lite ..again rooted and flashed cm7.1 stable and got bootloop..this time i surfed net and found what shud hav been done ..
1)pull out the battery after the boootloop.
2)clear cache
3)reboot
tats it..the welcome window comes in no time..
so coming to the present issue, after flashing the smf did u get bootanimation with light passing over "android" againg and again ??

Check that u r using the latest RSD.
I have a Defy plus but the same thing happened to me before (black screen even no boot with vol up) so I connected my phone to the computer (I can't really remember if I powered with a vol up or not) but I got it recognized by the RSD. try connecting and powering on the the vol up if nothing just connect and see what will happen.
The most important thing is to use the latest version of RSD.
and please tell me if it worked.
I'm not responsible for anything.

[Help!] Bootloop.

So, I had some issues with my Defy+...
I tested the latest 4.1.2 nightly and seemed like my backup was corrupted (?!) and I had to flash a 2.3.6 BL-6 .SBF since the backup would make me enter a bootloop.
Well, I tried with different .SBFs and sadly all of them have the same effect: the flashing process moves smooth, except that in the moment when I'm asked to power it up it's entering a bootloop.
Now, my battery STILL has some inside, but trying to charge it won't work(gives me the "?" sign). Don't know what should I do. Should I leave the phone in the bootloop until the battery goes away and then to re-flash a .SBF?...
Or my flashing process wasn't good enough and there's a workaround I don't know?... I don't want to brick my phone forever.

Charge battery with mcgyver metod or with other defy & reflash it with 231 sbf. For more info read: http://forum.xda-developers.com/showthread.php?t=966537

So, there's no other option out there?...

Deformat said:
So, there's no other option out there?...
Click to expand...
Click to collapse
Recharge battery with mcgayver metod and reflash sbf, you'll need start from scratch, because your bootmenu was corrupted and you can't restore nandroid or reinstall zip

Deformat said:
So, I had some issues with my Defy+...
I tested the latest 4.1.2 nightly and seemed like my backup was corrupted (?!) and I had to flash a 2.3.6 BL-6 .SBF since the backup would make me enter a bootloop.
Well, I tried with different .SBFs and sadly all of them have the same effect: the flashing process moves smooth, except that in the moment when I'm asked to power it up it's entering a bootloop.
Now, my battery STILL has some inside, but trying to charge it won't work(gives me the "?" sign). Don't know what should I do. Should I leave the phone in the bootloop until the battery goes away and then to re-flash a .SBF?...
Or my flashing process wasn't good enough and there's a workaround I don't know?... I don't want to brick my phone forever.
Click to expand...
Click to collapse
Once you have flashed the sbf and back on stock you need to go into the moto recovery and do a restore to default / format system. that should get around the boot loop issue... at least it did for me...

Can't acsess anything
locn said:
Once you have flashed the sbf and back on stock you need to go into the moto recovery and do a restore to default / format system. that should get around the boot loop issue... at least it did for me...
Click to expand...
Click to collapse
Hi together, well I hope this is the right place.... I'm owner of a motorola Defy MB 525 that ran without any problems on cm9 nightly for last 6 month. Now suddenly it doesn't start any moer andIi can't access recovery setup nor anything else so it's impossible to wipe anything, too. When connected to my notebook only the white LED is shining but nothing happens. The typical "hardware-found-ping" appears and several seconds later the " hardware was removed ping." The right drivers are installed on my notebook, but even RSD Lite doesn't found my Defy so I can't flash enything. Anyone has any Idea what to to?
Thank's in advance for any help!
Heddi

Heddi72 said:
Hi together, well I hope this is the right place.... I'm owner of a motorola Defy MB 525 that ran without any problems on cm9 nightly for last 6 month. Now suddenly it doesn't start any moer andIi can't access recovery setup nor anything else so it's impossible to wipe anything, too. When connected to my notebook only the white LED is shining but nothing happens. The typical "hardware-found-ping" appears and several seconds later the " hardware was removed ping." The right drivers are installed on my notebook, but even RSD Lite doesn't found my Defy so I can't flash enything. Anyone has any Idea what to to?
Thank's in advance for any help!
Heddi
Click to expand...
Click to collapse
Do you connect it to RSD in bootloader mode? Volume + when powering on. What is on the screen then?
Deformat said:
So, I had some issues with my Defy+...
I tested the latest 4.1.2 nightly and seemed like my backup was corrupted (?!) and I had to flash a 2.3.6 BL-6 .SBF since the backup would make me enter a bootloop.
Well, I tried with different .SBFs and sadly all of them have the same effect: the flashing process moves smooth, except that in the moment when I'm asked to power it up it's entering a bootloop.
Now, my battery STILL has some inside, but trying to charge it won't work(gives me the "?" sign). Don't know what should I do. Should I leave the phone in the bootloop until the battery goes away and then to re-flash a .SBF?...
Or my flashing process wasn't good enough and there's a workaround I don't know?... I don't want to brick my phone forever.
Click to expand...
Click to collapse
If you haven't flashed yet try to keep with BL6 sbfs, and not BL7 like 231.
After battery charge try to get to stock recover (volume down when powering on) and wipe data/factory reset before flashing.

bootloader
corrinti said:
Do you connect it to RSD in bootloader mode? Volume + when powering on. What is on the screen then?
If you haven't flashed yet try to keep with BL6 sbfs, and not BL7 like 231.
After battery charge try to get to stock recover (volume down when powering on) and wipe data/factory reset before flashing.
Click to expand...
Click to collapse
Hi, I can't enter bootloader mode, nor anything else. The screen stays dark and the phone doesn'treact. Only mi notebook pings when i press the startbutton one phone. Once for Hardware detected and seconds later for hardware removed. from time to time the notebook tries to find drivers, but couldn't and abort searching.
Chris

Heddi72 said:
Hi, I can't enter bootloader mode, nor anything else. The screen stays dark and the phone doesn'treact. Only mi notebook pings when i press the startbutton one phone. Once for Hardware detected and seconds later for hardware removed. from time to time the notebook tries to find drivers, but couldn't and abort searching.
Chris
Click to expand...
Click to collapse
And your battery? Is it charged?

[Q] Black screen and bootloop

Hi,
1. I rooted my phone successfully.
2. I installed droid2recovery.apk
3. Restarted. Installed CM10 and Gaaps (wrong version)
4. Reboot. Everything was normal with some annoyances due to the wrong version of Gaaps.
5. Checked and the phone was already rooted in CM10. Installed droid2recovery.apk again. Reboot.
6. Trapped in bootloop.
7. Reboot and enter in system recover.
8. Tried to install CM10 and correct Gaaps. Not possible due to failed to verify whole-file signature.
9. Discover that official recover mode doesn't install unofficial roms.
10. Searched for official roms of Milestone 2 BR. All links are broken.
11. I flashed downgrade_for_bl_3 with RSD Lite. Everything was ok. PASS.
12. Still bootloop. Enter in recover mode. Black screen. Can't see the android icon with exclamation mark.
Is my phone a paper holder now? Please advise.

I'm really without luck today.
I manage to flash a SBF with Android 2.3.6, exactly like the one I had. But then I couldn't root, not with the same method I rooted mine, not with any other method.
Then I downloaded another SBF and used RSD Lite to flash it, and the phone completely died. RSD reported everything OK, PASS, Finished, perfect.
Now nothing happens. The phone is off, black screen. Completely dead. But if I hit Power + Vol - + Camera, the computer recognize. But nothing on the screen. I'm re-flashing the same SBF again.
Why different thing happen when I proceed the same way as I did in the past?
Why can't I just flash a recover boot that accepts direct installation of Cyanogen Mod 10???

douglasrac said:
I'm really without luck today.
I manage to flash a SBF with Android 2.3.6, exactly like the one I had. But then I couldn't root, not with the same method I rooted mine, not with any other method.
Then I downloaded another SBF and used RSD Lite to flash it, and the phone completely died. RSD reported everything OK, PASS, Finished, perfect.
Now nothing happens. The phone is off, black screen. Completely dead. But if I hit Power + Vol - + Camera, the computer recognize. But nothing on the screen. I'm re-flashing the same SBF again.
Why different thing happen when I proceed the same way as I did in the past?
Why can't I just flash a recover boot that accepts direct installation of Cyanogen Mod 10???
Click to expand...
Click to collapse
You have to flash that same Android 2.3.6 SBF file, you can't use any more that "another sbf". For rooting that 2.3.6 use this http://forum.xda-developers.com/showthread.php?t=1750277
http://forum.xda-developers.com/showthread.php?t=1758271 this can help too
After you get CM10 back running, do not use droid2recovery.apk anymore!

Thank you. That really helped.
After you get CM10 back running, do not use droid2recovery.apk anymore!
Click to expand...
Click to collapse
Why not?

Odp: [Q] Black screen and bootloop
douglasrac said:
Thank you. That really helped.
Why not?
Click to expand...
Click to collapse
Because you already have recovery and you don't need it... doing this you can destroy something (maybe 2-init or 2-boot), and you will need to recover your phone using RSD Lite.
via tapatalk

henediac said:
Because you already have recovery and you don't need it... doing this you can destroy something (maybe 2-init or 2-boot), and you will need to recover your phone using RSD Lite.
via tapatalk
Click to expand...
Click to collapse
Hi Douglas, did you get the milestone working again? I'm stucked with the same problem, the rsdlite recognize my cellphone I can flash it but the screen is black. Anything works
How do you fix it?

You can still flash other sbfs, but when do turn on, you need to go in recovery mode, than clear cache and data. It will start normally again.
To go to stock recovery hold when turn on "@" or "x", than when show the "android with ! " you hold volume - and foto or volume + and foto or the volume + and -, than you are in recovery.
Sorry about my English
I am showing all the option because I do not remember perfect what to do... But it works
Sent from my A953 using xda app-developers app

cant get it to work..anyone got a link to a froyo stock sbf?

@Yostarone
http://sbf.droid-developers.org/umts_milestone2/list.php
i don't know what froyo rom you want, so I put link to whole list. (build number for eu froyo is MILS2_U6_2.4.24).

paulimbr said:
Hi Douglas, did you get the milestone working again? I'm stucked with the same problem, the rsdlite recognize my cellphone I can flash it but the screen is black. Anything works
How do you fix it?
Click to expand...
Click to collapse
I didn't get it working. Did you?

douglasrac said:
I didn't get it working. Did you?
Click to expand...
Click to collapse
boot into stock recovery and do a full wipe. This will solve your problem.
Press Power and x (on your Hardwarekeyboard) for several seconds. Release the buttons and you will see a yellow triangle with an exclamationmark in it. Now press vol up and down key together. voilla you got it

lulli1 said:
boot into stock recovery and do a full wipe. This will solve your problem.
Press Power and x (on your Hardwarekeyboard) for several seconds. Release the buttons and you will see a yellow triangle with an exclamationmark in it. Now press vol up and down key together. voilla you got it
Click to expand...
Click to collapse
I wish it was that simple. After flashing the phone is completely dead. And now I cant even go to bootloader anymore.... :crying:

could your problem be battery related? do you have a chance to try using another battery?

lulli1 said:
could your problem be battery related? do you have a chance to try using another battery?
Click to expand...
Click to collapse
Hi,
Sorry for the late reply. I was charging the battery
No, the problem is not the battery. Nothing works anymore. The phone doesn't even turn ON. All Black screen, not even boot loop.
So I get into the bootloader and flash new room. I can see the SN Updated text. But that is it. After it doesn't work.
I flashed DOWNGRADE BL =3 and then I flashed MILA2_U6_3.12.0_SIGNED_US1MILESTONE2PERARB125LA016.0R_GSXMILETPERARLA_P022_A013_M006_HWp2a_WIG142538_Service1FF
Nothing. Black Screen.
Then I flash M2L_U6_4.5.2_51-27_R01_SIGNED_US1MILA2GBPERARB125LA001.0R_STABLE45LAMILETPERLA_P013_A028_M001_HWp2a_Service1FF.
Then I get boot loop.
:S

[Q] Defy Plus No Recovery

Hi,
I have had my motorola Defy Plus running cyanogen for a year or so. Various versions, 2nd init.
Recently I decided to upgrade to Cyanogen version http://forum.xda-developers.com/showthread.php?t=2515036
Got it installed and running ok but there were some glitches (maybe) so I started from scratch to be sure.
The method I used to completely re-initialise the phone is as follows.
repartitioned SD, wiped and flashed
DEFYPLUS_U3_4.5.1-134_DFP-231_BLUR_SIGN_USADEFYEMARAB1B8RTGB005.0R_PDS03C_USAJRDNGIBRRTGB_P023_A025_M002_Service1FF.sbf.gz
booted into stock android. installed framaroot - rooted.
installed 2nd init
installed twrp
updated recovery
wipe/reset
install cyanogen
The first time I did this it worked (but with some gapps glitches so to trouble shoot I thought I would start again.
Now this is the problem.
the second time when I tried to flash the stock rom RSD lite hung with "please manually reboot the phone"
After this it is impossible to get into stock recovery from the android triangle screen. When pressing both volume buttons the only thing that happens is the screen brightness toggles between light and dim.
I can get the phone to connect to RSD lite and I can flash ROMS - I have tried a few but I cannot get recovery, Always after flashing RSD says please manually reboot phone. The automatic reboot does nothing but get to the motorola or triangle screen, or a black screen sometimes.
Just to clarify - I have googled and tried many solutions, the main problem is that there is no stock recovery from the triangle screen so no solution that relies on this is working,
Any help appreciated. Thanks.

Stock recovery is included in the ... stock ROM (duh) so you need to install completely the stock ROM. But anyway at what serve stock recovery for you?

pgreed said:
Stock recovery is included in the ... stock ROM (duh) so you need to install completely the stock ROM. But anyway at what serve stock recovery for you?
Click to expand...
Click to collapse
The one that usually works is DEFYPLUS_U3_4.5.1-134_DFP-231_BLUR_SIGN_USADEFYEMARAB1B8RTGB005.0R_PDS03C_US AJRDNGIBRRTGB_P023_A025_M002_Service1FF.sbf.gz
Which is the retail UK version for my phone. However when I try to flash it now with RSD it gets to the reboot stage but I am not sure it completes.

deMangler said:
The one that usually works is DEFYPLUS_U3_4.5.1-134_DFP-231_BLUR_SIGN_USADEFYEMARAB1B8RTGB005.0R_PDS03C_US AJRDNGIBRRTGB_P023_A025_M002_Service1FF.sbf.gz
Which is the retail UK version for my phone. However when I try to flash it now with RSD it gets to the reboot stage but I am not sure it completes.
Click to expand...
Click to collapse
I think what would solve my problem would be a way of installing the above rom (which I believe includes the bootloader). I need to solve the problem of the flashing not progressing beyond the reboot stage.
I am using RSD Lite version 6.1.4
Any help appreciated. Thanks.

Boot in recovery. Do a total wipe (factory reset). Reboot in bootloader. Flash the .sbf.

pgreed said:
Boot in recovery. Do a total wipe (factory reset). Reboot in bootloader. Flash the .sbf.
Click to expand...
Click to collapse
There is no functioning recovery, so it is impossible to do a wipe. It is possible to flash a stock ROM (which should restore the recovery) using RSD lite but the process does not get past the reboot stage.

download again the sbf or flash another sbf.

pgreed said:
download again the sbf or flash another sbf.
Click to expand...
Click to collapse
Thanks - good advice I have been trying that. Meanwhile I will be looking out for other ways of solving the problem. I will let this thread know if anything works.
Thanks everyone.

deMangler said:
Thanks - good advice I have been trying that. Meanwhile I will be looking out for other ways of solving the problem. I will let this thread know if anything works.
Thanks everyone.
Click to expand...
Click to collapse
I am not supposed to be cynic. That was happened to me a few times and eventually I can managed to make a complete flash. Try again.

pgreed said:
I am not supposed to be cynic. That was happened to me a few times and eventually I can managed to make a complete flash. Try again.
Click to expand...
Click to collapse
Thanks - I will let you know if it works.

deMangler said:
Thanks - I will let you know if it works.
Click to expand...
Click to collapse
I had the same problem and solved.After flash with RSD lite it stusk on Moto logo and pulsing,pullsing...,So disconenct from cable and remove baterry.Then conect baterry and turn on fone with Volume + and power at the same time to go into recovery.Yes it show a warning in triangle and I thing IM FU**ED it have no recovery.But just pushing the butons wtih angry(not remember the order) and it come in stock recovery.Then wipe everything that can wiped and reboot.It works and phone go to work.

same here - but your report helped!
I had the same problem and did what you did... boot with vol+down and power and got to the triangle. then press UP+DOWN fast after another. what follows is the recovery!
propov said:
I had the same problem and solved.After flash with RSD lite it stusk on Moto logo and pulsing,pullsing...,So disconenct from cable and remove baterry.Then conect baterry and turn on fone with Volume + and power at the same time to go into recovery.Yes it show a warning in triangle and I thing IM FU**ED it have no recovery.But just pushing the butons wtih angry(not remember the order) and it come in stock recovery.Then wipe everything that can wiped and reboot.It works and phone go to work.
Click to expand...
Click to collapse