Related
Hi Guys,
I am not sure if I am posting in the right place, but I could use some assistance on the Team EOS nightlies. They won't let me post in the DEV section yet, becuase I am mostly reader, not a poster. Anyway....
I've been running the EOS roms for a while, but I can't seem to run any nightly past 74. 74 runs great, when I tried to update to 75 (rom/gapps/wipe cache) it won't get past the "DUAL CORE" logo. I thought I bricked my xoom, but I am able to boot to recovery, reflash 74 (gapps/wipe) and it boot with no issue. I did a full wipe, and tried again with 76 but no joy (77 wasn't out at the time). I thought it was a problem with n75 and n76. I flashed back to n14 and it works fine, and I can upgrade back to n74. Tonight I tried to update again to n77, but still no dice. I let it sit for 15 minutes at the "Dual Core" logo, and all I noticed is that is got warm, but still no boot.
Any thoughts? All advise is welcome!
BTW, this is for a Stingray 4g xoom
And while I have your attention, I love the work you guys do, and this community, it really makes Android something special!
Weird. Try going into fastboot and do a full wipe of userdata, cache, and system. Then install. If need be, do a backup. This will totally wipe your device.
Wipe cache, wipe dalvik, flash ROM, flash GAPPS, fix permissions. Do it in that order and you should be fine.
Also make sure your using the latest GAPPS. It should be dated 2012-03-17.
Good Luck.
Still not working right, very frustrated, but I have new information
dellenrules said:
Wipe cache, wipe dalvik, flash ROM, flash GAPPS, fix permissions. Do it in that order and you should be fine.
Also make sure your using the latest GAPPS. It should be dated 2012-03-17.
Good Luck.
Click to expand...
Click to collapse
bigrushdog said:
Weird. Try going into fastboot and do a full wipe of userdata, cache, and system. Then install. If need be, do a backup. This will totally wipe your device.
Click to expand...
Click to collapse
Thanks to both of you. I did try this. What I have discovered so far is that some of the flashing fun I have been doing with my may have caused so minor issues with my external SD Card. I backed up the internal to it, and pulled it. I went through the process of nuking the xoom entirely. I.E. Wiped Cache, dalvik, full wipe, factory reset, reset permission, and deleted everything off the internal SD (wasn't in this order, but it all got done) I was able to flash N77, without GAPPS fine. It seemed to run faster with nothing else installed. Rebooted a few times, no problem. I was stoked. I flashed gapps, 03-17 version (the latest). factory reset again so that it was fresh and wiped the cache (just in case). It booted again no problems, ran me through initial config, and then began downloading my apps back. It seemed to run much faster than it ever did before.
Then I rebooted it, without doing any titanium backup restores, just fresh tablet, N77 with my 90 or so apps freshly installed from the market, and it froze again at the "Dual Core" boot screen. I waited hoping for some delayed joy, but none came.
So I went back through the process once again, factory reset, N77 install, wipe cache, install GAPPs. Booted.....initial config, auto downloaded 90 apps from market, reboot......dead.
So then I just flashed N74 again, wiped cache, install GAPPS, initial config, app download.....reboot.......works fine.
<general frustration directed at tablet, not anyone here/>
What gives???? I can't tell what the difference in internal apps in the ROM are that could be conflicting with the ones installed from the market.
Why the hell is N74 working and N77 not, when the apps in both ROMs look the same?
Why does N77 work great when the apps aren't restored?????
Why don't I make a million dollars?????
Why aren't I emperor of the universe???????????????
</general frustration directed at tablet, not anyone here>
Thanks much for all your help!
alright.... i have 2 suggestions these may not work and the second one is a pain in the butt to do but it got me out of a jam way back when i lost my softkeys no matter what i flashed
firstly.. in the sequence of your flashing throw in the 'format /system' see if that has any effect it is 'possible' the system is not being flashed correctly or it could be possible that it is getting corrupted and causing the bootloops (i always format system when full wiping)
second... and this is a pain.. but you can always try flashing back to STOCK... there could be other factors that aren't being flashed or fixed correctly causing ya problems... you can then go through the process and flash directly to the latest build... as i noted earlier this fixed a problem that nothing else could for me and has helped others but really this is a last last resort as it takes alot of time and screwing around
lastly... i have no idea sorry these are all i can input.. if possible can always try and use logcat while booting to see what is causing the crash if im not mistaken and upload a log and one of the devs may be able to have a look at it...
I Would stop dinking around with n77 and go to n90 I had the same issues around those nightly numbers, so I went all the way back to stock... (honeycomb) didn't fix it but I redid the whole install on a higher number and it seems to work itself out..... long story short try another maybe the 1.0 stable by them.
fkntwizted said:
I Would stop dinking around with n77 and go to n90 I had the same issues around those nightly numbers, so I went all the way back to stock... (honeycomb) didn't fix it but I redid the whole install on a higher number and it seems to work itself out..... long story short try another maybe the 1.0 stable by them.
Click to expand...
Click to collapse
He has the STINGRAY not the WINGRAY Xoom.
N77 is the latest for the 4G version. The version he has.
Read the OP
EOS Nightlies hate my xoom, my Xoom wanted CM9 I guess
joshndroid said:
alright.... i have 2 suggestions these may not work and the second one is a pain in the butt to do but it got me out of a jam way back when i lost my softkeys no matter what i flashed
firstly.. in the sequence of your flashing throw in the 'format /system' see if that has any effect it is 'possible' the system is not being flashed correctly or it could be possible that it is getting corrupted and causing the bootloops (i always format system when full wiping)
second... and this is a pain.. but you can always try flashing back to STOCK... there could be other factors that aren't being flashed or fixed correctly causing ya problems... you can then go through the process and flash directly to the latest build... as i noted earlier this fixed a problem that nothing else could for me and has helped others but really this is a last last resort as it takes alot of time and screwing around
lastly... i have no idea sorry these are all i can input.. if possible can always try and use logcat while booting to see what is causing the crash if im not mistaken and upload a log and one of the devs may be able to have a look at it...
Click to expand...
Click to collapse
Thanks much for this. I had already attempted the formatting of everything except the SD card before.....but for sh*ts and giggles I tried it one more time. unfortunately that didn't work.
Using the second option, of reverting stock, I went through sleeplessnija's tutorial on reverting. It really didn't seem that bad, taking me longer to setup my work machine than it did to send the fastboot commands. I was able to get it to boot stock (of course I didn't re-lock it) just fine, and it was quick....so it seems like my hardware is fine.
I used fastboot to put the replacement tiamat recovery, and formatted everything in the mounts menu again. I also mounted my SD card as USB storage and used the full format for it under windows. Then i copied N77 and GAPPS back to it, and re-installed them. It got to the second boot logo (first was the shaking team eos, the second is the square thing with rounded corners that moves). It hung for about 10 minutes, and I shut it off. annoyed.
So I went back into recovery, mounted my SD for USB access from my desktop, and copied the unofficial (which I think is now official) CM9 distro from Team Rogue (Steady's Rom I believe?). I formatted everything, and wiped everything (except the SD) again, and installed CM9 and gapps. Booted fine. Configured account, downloaded 90 apps, rebooted, no problems. Played with it for a while, rebooted....no problems.
I like that my xoom is back up and running......however it seemed that Steadies rom is just a little less fully featured than Team EOS. THAT IS NOT A KNOCK AGAINST TEAM ROGUE OR CM9.....my Xoom is working again (so far) thanks to him (them), and I run CM9 on my AT&T GSII. I just really like Team EOS on my Xoom, and have been with them since the beginning. I would love to know why my xoom suddenly hates the latest nightlies (everything since 74).
Edit: I forgot to ask, Joshndroid.....you mentioned running logcat to see what going on. If it can't boot past the dual core logo or the second boot logo from Team EOS....how do I get the logs? I am not familiar with android's logging.....even though I am a flash-a-holic. I am just thinking that if this is happening to me, maybe I can help out the devs (and myself, and maybe someone else) with the log output.
Edit 2: And Josh.....I forgot to tell you .....good call on the revert to stock answer. I didn't think about that before and thought I was screwed!
Thanks!!
I bought a refurbished TF101 about 6 months ago. I rooted the device and tried various ROMs until I settled upon "Revolver 4 by Gnufabio | 4.1.1 Stable". Life was good, no random reboots, no sleep of death just great. I then installed a game called "Dead Trigger" that came up recently on the Play store. The game did not load, crashed without a FC message and so I uninstalled it promptly. Then I started getting video corruption on my Live Wallpaper (Blue Skies). Random reboots soon followed. Time to start over.
I used CWM and wiped the tablet from there (data, cache and Dalvik) and reinstalled Revolver. It did not work. I used the EasyFlasher tool to return my tablet to Stock using the Asus provided firmware from their website (.24). It seemed to work well, as I started over with my "new" tablet and synced to my account, etc, etc, etc. But now I can't use it without it rebooting every 30secs to 1min. It will go into a Sleep of Death on a random basis also. I have not installed any programs on it, I tried not allowing a restore of my Google settings and cannot for the life of me figure out what is going on.
I am unaware of the SBK version, as their is no indication on the tablet of its serial. What vital step am I missing here to revive this tablet? Any help would be appreciated.
Thanks
StevieJake
steviejake said:
I bought a refurbished TF101 about 6 months ago. I rooted the device and tried various ROMs until I settled upon "Revolver 4 by Gnufabio | 4.1.1 Stable". Life was good, no random reboots, no sleep of death just great. I then installed a game called "Dead Trigger" that came up recently on the Play store. The game did not load, crashed without a FC message and so I uninstalled it promptly. Then I started getting video corruption on my Live Wallpaper (Blue Skies). Random reboots soon followed. Time to start over.
I used CWM and wiped the tablet from there (data, cache and Dalvik) and reinstalled Revolver. It did not work. I used the EasyFlasher tool to return my tablet to Stock using the Asus provided firmware from their website (.24). It seemed to work well, as I started over with my "new" tablet and synced to my account, etc, etc, etc. But now I can't use it without it rebooting every 30secs to 1min. It will go into a Sleep of Death on a random basis also. I have not installed any programs on it, I tried not allowing a restore of my Google settings and cannot for the life of me figure out what is going on.
I am unaware of the SBK version, as their is no indication on the tablet of its serial. What vital step am I missing here to revive this tablet? Any help would be appreciated.
Thanks
StevieJake
Click to expand...
Click to collapse
The RR and SoD come standard with asus stock FW for most people, there is a new .27 update you could try that apparently fixes things, but it made things worse for me
The serial number is generally on a sticker next to the charger port of the tablet half, B4O > B60 and some B7O are SBK1, after that are SBK2
If you are SBK1 you can use NVFLASH to clean install the OS
I decided on Stock FW Rooted and CWM with PERI, then Guevors Kernel
So far so good, stable for a couple days now
Thanks for the quick reply. I did try the .27 update OTA update after getting back to Stock. No help.
The sticker in question is missing. Unknown SBK. I used EasyFlasher using SBK Ver1 and it worked to install the Stock .24 OS fine.
I will give the Stock FW Rooted a shot and see if that works
StevieJake
steviejake said:
Thanks for the quick reply. I did try the .27 update OTA update after getting back to Stock. No help.
The sticker in question is missing. Unknown SBK. I used EasyFlasher using SBK Ver1 and it worked to install the Stock .24 OS fine.
I will give the Stock FW Rooted a shot and see if that works
StevieJake
Click to expand...
Click to collapse
If the flash worked with sbkv1, then more than likely the unit is sbkv1. Otherwise, it shouldn't have worked at all . As the other poster said, RR and SoD is pretty common with the stock Asus firmware for some people -- you might try returning to Revolver now that you've gone back to stock, and start on Revolver again with a clean slate.
I am also running the same setup as the previous poster, stock .27, rooted with guevor's kernel. Been that way for only a day right now, so I can't say much about it yet.
Okay, so here is what I have done. I first used NvFlash to flash Stock .24 successfully. I then extracted the ASUS .24 firmware file (zip only) to the MicroSD card which the system took as an update and installed over my good work. It works, albeit with reboots still. I at least got it working and will try some more ROMs (Stock .27 first) with the suggested kernel. I just wish I could get back to the stable Revolver I had earlier.
Thanks for the help and suggestions.
StevieJake
steviejake said:
Okay, so here is what I have done. I first used NvFlash to flash Stock .24 successfully. I then extracted the ASUS .24 firmware file (zip only) to the MicroSD card which the system took as an update and installed over my good work. It works, albeit with reboots still. I at least got it working and will try some more ROMs (Stock .27 first) with the suggested kernel. I just wish I could get back to the stable Revolver I had earlier.
Thanks for the help and suggestions.
StevieJake
Click to expand...
Click to collapse
If you used NVFLASH to get back to stock, you could have just let the FOTA update you to .27
Then you can root and so on after that
NVFLASH returns the tablet to factory settings, ie. as it was when you unwrapped it on day 1
Not good. My tablet seems to be in an internal storage hell. Every Rom I try to install will crash with moderate use after booting. I have tried NvFlash, EasyFlash, Wolfs Ultimate flash and downgrade, every variation of stock HoneyComb and ICS I can find. I cannot keep this thing stable beyond 5 minutes of use. I have tried multiple factory resets and wipes, run "Superwipe Full" multiple times and nothing seems to work. What can I do to recover this tablet before I just give up and send to ASUS (god help me) for assistance? Any help would be appreciated
Thanks StevieJ
Ouch. Sorry to hear about your troubles. Horror stories like this have prevented me from diving into the root and custom rom scene with my one and only tab. [I am leaning towards a Nexus 7 when it comes out, and will perhaps root etc when I get that. I feel like it's a safer endeavour with a non-locked bootloader]
I'm interested in finding out what may be causing all this, so I'll be subscribing to this thread. Sorry I can't provide anything more than good luck to you.
Sent from my Transformer TF101
Ouch is right! I have rooted every Android device I have ever owned and this the first I have ever had this much trouble with. I just wish I could say I did "X" to cause it to happen. Oh well, maybe somebody knows something I have overlooked.
Note: I have Rogue XM Recovery 1.5.0 (CWM-based Recovery v5.0.2.8) running fine on the rom and it reboots into recovery okay.
StevieJake
steviejake said:
Ouch is right! I have rooted every Android device I have ever owned and this the first I have ever had this much trouble with. I just wish I could say I did "X" to cause it to happen. Oh well, maybe somebody knows something I have overlooked.
Note: I have Rogue XM Recovery 1.5.0 (CWM-based Recovery v5.0.2.8) running fine on the rom and it reboots into recovery okay.
StevieJake
Click to expand...
Click to collapse
Have you tried running it without the WIFI on? I went to my folks place with mine and it rebooted all the time as soon as it started up. It turned out to be a WIFI issue with the Dynalink router my parents were running.
Cheers, Matt.
hairy1 said:
Have you tried running it without the WIFI on? I went to my folks place with mine and it rebooted all the time as soon as it started up. It turned out to be a WIFI issue with the Dynalink router my parents were running.
Cheers, Matt.
Click to expand...
Click to collapse
Funny you should ask that. I just NvFlashed 9.2.1.24 and was using the tab with no WiFi, no account information and everything worked just fine. I then enabled WiFi to see what would happen and it still worked, but I had not logged in with any account information yet. It still worked fine, as I was able to surf the web with no problems. I then tried to add my account information and started getting crashes using the Play Store, syncing my accounts, etc. It seems to be linked to updating account information and not just WiFi. I will investigate further
Thanks
StevieJake
Adding an account, even a new account, will bring down the tablet. It reboots until it is only a dark screen that requires APX mode (VolUp +Pwr) to rebuild the tablet. I can get into recovery and also factory reset mode (VolDwn + Pwr), but that is it. I'm so confused
I found a CWM backup I had from back in March. It restored fine, but still had problems that resulted in multiple crashes and eventual death again. Oh Bother!!
StevieJake
Fixed it!
Here is what I did. I was always to get the tablet into APX mode (Vol Up + Pwr) so I NvFlashed 9.2.1.24 from this site:
http://xdafileserver.nl/index.php?dir=Asus/Asus+Transformer+(TF101)/. I did this 5 times, never letting the tablet fully reboot after I got the "success" message upon completion. I then did a data wipe (Vol Dwn +Pwr, then select Wipe Data and then Vol Up, Vol Up) 5 times. I then used the same NvFlash 5 more times and let the tablet fully reboot and entered my Google credentials. I had prepared a MicroSD card with the zip file extracted from the ASUS site that contained the latest firmware (.27) and placed in the root directory of the MicroSD card. The tablet recognized it as a system upgrade and installed the firmware grade with no problems. The tablet rebooted fine and showed the installed firmware. I then did a data wipe as described above 5 more times and then let the tablet reboot fully and once again entered my Google credentials. The tablet now runs all programs without faults, has no video artifacts on the live wallpaper I use (Blue Skies) and is running just great. I am able to update all apps with out errors from the Play Store which was also an issue.
I hope this helps someone to get their tablet back, as I used all the resources on this forum to bring this wacky method to restore my tablet. Thanks to all you unnamed posters for your help
StevieJake
I wouldn't expect flashing the same thing numerous times to have any more effect than the first flash, but if that's what it took for your tab to be re-born, so be it!
Congrats on the fix.
Sent from my Transformer TF101
Not so fast!
Although the tablet did last longer (almost 2 days), it ultimately failed again to an unbootable state. Its back to the drawing board again.........
StevieJake
rootblock said:
I wouldn't expect flashing the same thing numerous times to have any more effect than the first flash, but if that's what it took for your tab to be re-born, so be it!
Congrats on the fix.
Sent from my Transformer TF101
Click to expand...
Click to collapse
It may just be giving up, electronics are stupid sometimes and fail for no reason. I had a brand new HDD that worked for two days, I left the computer off for three weeks and when I turned it back on the HDD wouldn't even spin up :-/ Good luck buddy.
Okay, I'm done. Just got my RMA and am sending this puppy in. Thanks for all the help, I will try to post the results later when I get it back. Glad I made the impulse purchase for the Nexus 7, as I will not be totally without a tablet.
Thanks for all the help again
StevieJake
RMA and back from the Dead!
Well I got it back from ASUS after the RMA. It had a short visit in Texas, was returned promptly and appears to function normally. I never received any feedback from ASUS on receiving the tablet, what was wrong with it, what they did to it or when they shipped it. But its fixed. Running .27 latest firmware and seems to handle everything I can throw at it.
They did a bang up job so far and I am more than happy with their service.
StevieJake
Hello All,
This is my first post. EVER. Honestly think I'm not breaking any rules for this, if I am, I apologize.
Here's my quagmire:
I rooted my gf's nook color a LONG time ago, like months, and all went well. I'm somewhat familiar with the concept/process or rooting, flashing ROMs, unbricking, and what have you. ANYWAY, she did something(I know not what) that resulted in me having to redo the whole process, a couple months ago. But I had used a Newer version of CyanogenMod ROM(infact, I might have used an ALPHA build), but it went well, only problem was since then, haven't been able to add Google accounts to the device, resulting in no PlayStore access. I've been having to manually transfer/install apk files to the blasted thing, for every app she decides she wants.
YES, I SHOULD HAVE simply reverted to a previous version/build of CyanogenMod, verified ability to add Goggle accounts, and left it at that, or upgraded from there, or something. And I still could, if need be...
BUT, I really wanted to run MIUI on it, see what she thought of that flavor...
SO... Thru CWMrecov, I installed the zip for MIUI 1.9.16... and it boots, and goes to the Introductive Screen and all that, Pwer/Volume Buttons work, not sure about the n Button, yet, because THE TOUCHSCREEN DOESN'T WORK A BIT, & IDK WHY :crying:
If ANYBODY could offer some words of assistance on the matter, I'd REALLY appreciate it.
And So as to not waste anyone's time, I'll answer the typical questions, before you ask:
* Yes, it installed correctly w/out aborting, in CWMrecov.
* Yes, I performed Cache Wipe, Dalvik Wipe, Battery Stats, etc PRIOR to installing, and...
* Yes, I performed same wipes AFTER installing, PLUS a factory user data reset & Fix Permissions.
* Yes, I have tried rebooting the nook several times to the "Touch The Android To Begin" screen, no different result.
* Yes, of COURSE I nandroid backup BEFORE going from Cyanogen to MIUI, So I can restore if no other option....
Also:
* I just downloaded the MIUI 2.4.6 and am gonna try installing that newer version, hopefully to some effect. I just wanted to get this out there, first, JUST IN CASE the problem persists...
I also gotta say THANKs to everybody, the DEVs, the Contributors, everyone out there working on all these devices, making them better and more unique. I've always Trusted XDA forums above all else. I do alot of browsing through the Forums, Now that I'm a member I'll start using the Thanks button as I should.
Thanks again. All.
Hi all. I used to mess with my Nook Color a lot around a year and a half ago but recently was just using it to read and occasionally browse. I'm 99% sure I was working with just a nook which was used with manual nooter, so that I had the Google Play store and Zeam launcher with stock B&N as well. I was having issues with things "not being able to update" so I tried to mess around, only realizing too late that I wasn't really interested in cm10 and wanted to stick with zeam. Since then I've been trying to get back to how I started but I'm failing miserably. I've so far tried wiping/factory resetting my device. Installing cm7 from zip, resetting everything using the guide here and installing 1-4-1 cam oc zip from here and still I fail. I can get into the set up screen, but when the device will not find any wifi signal and then freeze without allowing me to type it in under "other". Honestly I'm not sure what else to do now. I just want my nooted device back -__-.
Please let me know if I can submit any more information that can help solve this problem. Thank you for your time.
I'm literally infinitely stuck staring at this screen.
Managed to fix everything. Used section A15. Enjoy anyone who ran into similar trouble.
Hi guys. Over the weekend, I was running Android O beta, just to give it a spin and see how it was. Everything was working ok, but then I missed the good features of AOSP, so I decided to come back to it. So on Sunday night, I flashed back the previous rom, including the vendor, bootloader and radio as requested on the OP. But the problem was that the screen rotation wasn't working, no matter what I tried. I even tried other roms, to see if the problem was from the rom, but no, the problem persisted. I flashed stock again, and the problem was also there. I gave Google a call and they sent me some steps to go through and none of them solved my problem as well. So, I decided to flash back the O Beta, and voila, the problem was gone. My question, have I done anything wrong, any step that I may have missed? Or is it the drivers? Any help/suggestion is highly appreciatted
Did you factory reset or wiped data? It's sometimes necessary when downgrading.
I did yes. It was the first thing I did as soon as I got TWRP installed on it,because it was asking for the encryption key, to which it never what it was(tried my password and my lock screen code,but none of them worked,so just ended up wiping the whole data)