Database Users

CM9 Stuck on boot screen :(

Hello...
i installed Cm9 followed the exact procedures give in http://www.youtube.com/watch?annota...&feature=iv&src_vid=5YJDcHjESKk&v=3v9OQY7yz7U
but now i am stuck at the CM9 boot screen.. i have an infinite boot...
i didnt take a nandroid backup...
i have the sbf files n rds lite, but it wouldnt let me go into it.. cm9 starts immediately after i plugin usb...
i tried re-flasing it.. no use.. please help...

Wipe data/factory reset.. and wipe cache partition..
after flashing the custom rom . . . . !

If wipe data/cache doesn't work.go to bootmenu and boot options.if adb is disabled...enable it.worked for me TODAY...after updating to a newer build it happened.
Sent from my MB526 using XDA

i cleared cache,dalvik,data.. n i also enabled adb.. no use.. can i load a nandroid i dowloaded from the net.. ? would it work?

what's your phone defy or defy+, green or red lens, which build did you instal?

i have Defy, green lens, i installed CM9 nightly [CM9-NIGHTLY-120416-Defy]
used CM7 kernel n gapps...
any help would be appreciated... thanks in advance...

Try the whole procedure once again:
Get latest build (Epsylon's for example): http://defy.wdscript.fr/defy-cm9/CM9-NIGHTLY-120428-Defy.zip
Kernel: http://m.cfa.aero/misc/CM7_Kernel-signed.zip
Gapps: http://cmw.22aaf3.com/gapps/gapps-ics-20120317-signed.zip
Place them on sdcard, go to stable recovery and do as following:
- wipe data/factory reset
- install zip from sdcard: ROM > KERNEL > GAPPS
- wipe cache partition, advanced > wipe dalvik cache then reboot
First boot can take a while. Good luck!

I switched on the defy holding powerup n entered SW update mode...
used rds lite n installed sbf.. my defy is back again..
i will try installing CM9 again now.. thanks All for ur timely support...

[email protected] said:
I switched on the defy holding powerup n entered SW update mode...
used rds lite n installed sbf.. my defy is back again..
i will try installing CM9 again now.. thanks All for ur timely support...
Click to expand...
Click to collapse
See this link it might help you: http://forum.xda-developers.com/showthread.php?t=1618904

[email protected] said:
Hello...
i installed Cm9 followed the exact procedures give in http://www.youtube.com/watch?annota...&feature=iv&src_vid=5YJDcHjESKk&v=3v9OQY7yz7U
but now i am stuck at the CM9 boot screen.. i have an infinite boot...
i didnt take a nandroid backup...
i have the sbf files n rds lite, but it wouldnt let me go into it.. cm9 starts immediately after i plugin usb...
i tried re-flasing it.. no use.. please help...
Click to expand...
Click to collapse
May be this post will help you...
Link

[Q] update cm9 to cm10 2ndboot

I want to go from cm9 to cm10 2ndboot on my defy.
I think I've read the relevant threads about doing this and ask here just to get a last 'ok' from here...
I have downloaded the CM10-20121018 nightly and the update for it. So I unpack the CM10 copy the update over it and pack it again.
Then I'll do:
wipe data *sigh*
wipe cache and dalvik
flash cm10 2ndboot version
flash google apps
wipe dalvik and cache again
switch 2ndinit boot method to 2ndboot ( <-- is this ok. ? )
reboot
by the way, where can I see my 2ndinit version?
After entering the boot menu it says at the top of the screen: "Android Bootmenu v1.3.0 ICS"
Is this the version of 2ndinit? I thought it should be something over 2 ...
Thanks
Michael

Just flash the nightly and then flash the update. The nightly should automatically change the boot method to 2nd-boot.
In case anything goes wrong, make a nandroid backup first.
Sent from my Nexus 7 using xda app-developers app

Thanks for the answer. Somehow missed that I can just flash the rom and then the update, no need to merge them before flashing.
ralphx10 said:
Just flash the nightly and then flash the update. The nightly should automatically change the boot method to 2nd-boot.
In case anything goes wrong, make a nandroid backup first.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse

Worked like a charm. I'm very happy with this version, great work.
Now I have to convince a friend of me to let me put this on his defy+ . He experiences random reboots and other bad things (camera not working, losing photos...) . I hope this goes away with CM10, allthough it maybe a hardware bug...
Michael

[Q] Last version of CM10.1 for defy (mb525)

Hello,
I own a defy mb525 with CM7.2.0. I am not so happy with this version (bad 3g access; battery life very short)
So I decided to install the CM10.1.
On the develloper page I saw that the status has been updated on the 26.03. But if I look for my model (mb525), I can find only a version dated on the 120904.
Is there a newer version for the mb525 or is it only for the mb520 and mb526 ?
Regards

http://forum.xda-developers.com/showpost.php?p=34616788&postcount=1
--> FAQ2
It should work for both. Same as latest builds of CM10.

thubi said:
http://forum.xda-developers.com/showpost.php?p=34616788&postcount=1
--> FAQ2
It should work for both. Same as latest builds of CM10.
Click to expand...
Click to collapse
Sorry I was meaning the 4.1.2 so it should be the 10.0

Cid156 said:
Hello,
I own a defy mb525 with CM7.2.0. I am not so happy with this version (bad 3g access; battery life very short)
So I decided to install the CM10.1.
On the develloper page I saw that the status has been updated on the 26.03. But if I look for my model (mb525), I can find only a version dated on the 120904.
Is there a newer version for the mb525 or is it only for the mb520 and mb526 ?
Regards
Click to expand...
Click to collapse
2ndboot builds: they are one build for both mb525 &5 26 .... so you can download the 26.03 nightly build and update on your MB525 :good:

Cid156 said:
Hello,
I own a defy mb525 with CM7.2.0. I am not so happy with this version (bad 3g access; battery life very short)
So I decided to install the CM10.1.
On the develloper page I saw that the status has been updated on the 26.03. But if I look for my model (mb525), I can find only a version dated on the 120904.
Is there a newer version for the mb525 or is it only for the mb520 and mb526 ?
Regards
Click to expand...
Click to collapse
Yes, there is CM10 from Quarx. Your device can be either mb525 or mb526 with red lens or green lens. CM10.1 from the same person also can.

hi
I have a similar question I have MotoDefy 525 running 2.3.7 I want to install ([ROM][JB+][4.3.1] MokeeOS 43.1 Defy/Defy(+) Official) http://forum.xda-developers.com/showthread.php?t=2453395
but it needs TWRP I tried installing on my 2.3.7 but it dosent install I looked around the forms I read that I have to up date my android version.
being a newbi im a little worried about bricking
A little help
can some one give the steps in Newbi language on how to update my phone to MokeeOS 43.1 please.:fingers-crossed:

Super_Moto said:
hi
I have a similar question I have MotoDefy 525 running 2.3.7 I want to install ([ROM][JB+][4.3.1] MokeeOS 43.1 Defy/Defy(+) Official) http://forum.xda-developers.com/showthread.php?t=2453395
but it needs TWRP I tried installing on my 2.3.7 but it dosent install I looked around the forms I read that I have to up date my android version.
being a newbi im a little worried about bricking
A little help
can some one give the steps in Newbi language on how to update my phone to MokeeOS 43.1 please.:fingers-crossed:
Click to expand...
Click to collapse
First of all, none of you guys ever read the stickies. It is packed with good info.
Our phone has a locked bootloader, it is almost impossible to brick.
Download latest CM10 and then install.

Ive come across a newbi problem im on the link of the latest cm10 (http://forum.xda-developers.com/showthread.php?t=1768702) and the file I try to flash wont install it gets aborted, I searched the forms for other cm10 and same issue file gets aborted.
If possible to be directed to the file I need to flash to cm10
not easy being newbi these days :crying:
Motorola 525 green lens running 2.3.7

What error do you get?
Sent from my MB526 using Tapatalk

hotdog125 said:
What error do you get?
Sent from my MB526 using Tapatalk
Click to expand...
Click to collapse
the error shows when I try to flash the .zip file _Install zip from sdcard_choose zip from sdcard I pic the file and it doesn't install it says aborted show me the yellow triangle symbol I was assuming im flashing the wrong file.
before I do an install I wipe data/factory reset and wipe cache partition

Super_Moto said:
the error shows when I try to flash the .zip file _Install zip from sdcard_choose zip from sdcard I pic the file and it doesn't install it says aborted show me the yellow triangle symbol I was assuming im flashing the wrong file.
before I do an install I wipe data/factory reset and wipe cache partition
Click to expand...
Click to collapse
You are trying to flash through stock recovery. Install through custom recovery.

hotdog125 said:
You are trying to flash through stock recovery. Install through custom recovery.
Click to expand...
Click to collapse
I tried that and im also giving me (installation aborted) I used file cm-10-20130918-NIGHTLY-mb526 but no luck

Super_Moto said:
I tried that and im also giving me (installation aborted) I used file cm-10-20130918-NIGHTLY-mb526 but no luck
Click to expand...
Click to collapse
The file is ok, i've installed it on my defy

MikBre said:
The file is ok, i've installed it on my defy
Click to expand...
Click to collapse
Im clue less what im doing wrong I looked on u tube on installing jelly bean im following the same steps but Im getting (file aborted) when I try flashing the file
what r the steps u take on installing the file ?
At first I tried: Reboot in _Recovery _Install zip from sdcard_choose zip from sdcard_pick the the file _yes install
it starts by saying
Finding update package...
Opening update package...
E:Can't open /sdcard/cm-10-20130918-NIGHTLY-mb526.zip
(bad)
Installation aborted.
2nd I tried
Reboot in Bootmenu
Recovery _ Custom Recovery etc ..etc ..
and get the same message
Finding update package...
Opening update package...
E:Can't open /sdcard/cm-10-20130918-NIGHTLY-mb526.zip
(bad)
Installation aborted.
always did the factory rest and wiping during both process

Super_Moto said:
Finding update package...
Opening update package...
E:Can't open /sdcard/cm-10-20130918-NIGHTLY-mb526.zip
(bad)
Installation aborted.
Click to expand...
Click to collapse
just to be sure, your phone is not connected to a computer when you did the flash, right?

jh20 said:
just to be sure, your phone is not connected to a computer when you did the flash, right?
Click to expand...
Click to collapse
yes phone is disconnected from computer,I had no issues installing cm7
My is CMRecovery v5.0.3.2-jordan
and Bootmenu <v1.1.1> could these be the problem some thing needs to be updated ?

Super_Moto said:
what r the steps u take on installing the file ?
Click to expand...
Click to collapse
If you want a video guide look at the Youtube channel of locslikes.
Therre is a guide call "MOTOROLA DEFY How To Install ClockWorkMod and Cyanogenmod 10 Jelly Bean Android"

MikBre said:
If you want a video guide look at the Youtube channel of locslikes.
Therre is a guide call "MOTOROLA DEFY How To Install ClockWorkMod and Cyanogenmod 10 Jelly Bean Android"
Click to expand...
Click to collapse
Im just guessing.... that my bootmenu seems to be out of date possible being the reason that jellybean wont install,
bootmenu is up to 2ndInit Recovery v2.3 can this file be installed over v1.1.1 ?

Super_Moto said:
Im just guessing.... that my bootmenu seems to be out of date possible being the reason that jellybean wont install,
bootmenu is up to 2ndInit Recovery v2.3 can this file be installed over v1.1.1 ?
Click to expand...
Click to collapse
out of curiousity, i restored my mb525 back to cm7 nightly 20111201 nandroid, which has cwm v5.0.3.2. i did not check the bootmenu version but it should be the same as yours. then, after formatting system/cache partitions, i flashed cm-10-20130918-nightly-mb526.zip, and it worked.
so i don't really know what's wrong with your phone, but i have a couple of suggestions for you to try. not that there's any logical explanations but try it anyway:
1. according to the error messages, you have the cm10 rom in the root folder of the sdcard. try creating a sub-folder called cm10 and copy the cm10 rom and the minimal gapps into it.
2. download the defy_fullwipe_ext4.zip and defy_fullwipe_ext3.zip ( for later use, when you want to revert back your rom) from here and put them in cm10 folder as well:
http://forum.xda-developers.com/showthread.php?t=1818520
3. reboot into recovery but don't do any format or wipe. instead flash the file defy_fullwipe_ext4.zip and this will format your partitions into the ext4 file system.
4. then flash the cm10 rom. if it installs sucessfully, then without any further wiping,nor flashing the minimal gapps, reboot the phone. (note that the os will reboot once more in the middle of booting up, seemingly having a bootloop problem. don't worry it's meant to do that, unless it rebooted more than once)
5. if it boots up sucessfully, do some basic set up first before rebooting back into recovery to flash the minimal gapps.
alternatively you could try flashing cm9.1 (ext3) to get a newer bootmenu and cwm versions before flashing cm10. no need to flash any gapps, just wipe system/cache partitions and flash the cm9.1 rom by itself. reboot into cm9.1, do basic set up. once it's ready reboot into recovery and do the above steps, starting from step 3, to flash cm10.
good luck.....
edit: did you get your cm10 rom from here:
http://quarx2k.ru/cm10-2ndboot-nightly-defy(+)/

jh20 said:
out of curiousity, i restored my mb525 back to cm7 nightly 20111201 nandroid, which has cwm v5.0.3.2. i did not check the bootmenu version but it should be the same as yours. then, after formatting system/cache partitions, i flashed cm-10-20130918-nightly-mb526.zip, and it worked.
so i don't really know what's wrong with your phone, but i have a couple of suggestions for you to try. not that there's any logical explanations but try it anyway:
1. according to the error messages, you have the cm10 rom in the root folder of the sdcard. try creating a sub-folder called cm10 and copy the cm10 rom and the minimal gapps into it.
2. download the defy_fullwipe_ext4.zip and defy_fullwipe_ext3.zip ( for later use, when you want to revert back your rom) from here and put them in cm10 folder as well:
http://forum.xda-developers.com/showthread.php?t=1818520
3. reboot into recovery but don't do any format or wipe. instead flash the file defy_fullwipe_ext4.zip and this will format your partitions into the ext4 file system.
4. then flash the cm10 rom. if it installs sucessfully, then without any further wiping,nor flashing the minimal gapps, reboot the phone. (note that the os will reboot once more in the middle of booting up, seemingly having a bootloop problem. don't worry it's meant to do that, unless it rebooted more than once)
5. if it boots up sucessfully, do some basic set up first before rebooting back into recovery to flash the minimal gapps.
alternatively you could try flashing cm9.1 (ext3) to get a newer bootmenu and cwm versions before flashing cm10. no need to flash any gapps, just wipe system/cache partitions and flash the cm9.1 rom by itself. reboot into cm9.1, do basic set up. once it's ready reboot into recovery and do the above steps, starting from step 3, to flash cm10.
good luck.....
edit: did you get your cm10 rom from here:
http://quarx2k.ru/cm10-2ndboot-nightly-defy(+)/
Click to expand...
Click to collapse
I did try using that link but the files still would abort when flashing, also tried http://d-h.st/users/Quarx files it did the same thing
I followed your instruction but decided to goto cm 9 first I flashed the (ext3) file it installed and cm9.1 installed also installed twrp with no issues but when I was going through cm9 and its functions I couldent go on line a popup message (Unfortunately, brower has stopped) also I wasn't able to log on google play a pop up message (Unfortunately,com. google android.gb has stopped). so I got fed up and decided to goto cm10.1 so I first flashed with ext4.zip it installed and then tried to flash 10.1 file once again the file wouldn't install it gave me aborted file message again. I had no choice to reboot and I had to reinstall the factory file(brick). I am now back to where I started :silly: cm7 2.3.7 its been a hell of a weekend ........... ill give it another shot soon :fingers-crossed:

[Solved] Only with Quarx CM10: Status 7, Installation aborted?

Title says it all: I get symlink: some symlinks failed, status 7 error, installation aborted when I try to install Quarx's CM10 (2nd boot). Haven't tried any other JB, since I can't find any that fits. Maybe something with 2nd boot? It seems not to work on my phone...
I tried google-ing the problem, found some information about removing lines from updater-script, but the line was not even there (something with asserts).
Defy red lens MB525

Try a system wipe. That error is because of some filesystem problem, not 2ndboot
Sent from my MB526 using Tapatalk 2

I tried wiping with AROMA wiper yesterday: ext4, wipe data, system, cache, dalvik, then NO reboot and install cm 10... it failed as hell.

ive had the same issue as you with cm10 2ndboot. i moved on after trying to get it installed for months. 10.2 is awesome! just make sure you start from a fresh sbf flash and reroot and all that jazz. also, start with twrp!

undyingvisage58 said:
ive had the same issue as you with cm10 2ndboot. i moved on after trying to get it installed for months. 10.2 is awesome! just make sure you start from a fresh sbf flash and reroot and all that jazz. also, start with twrp!
Click to expand...
Click to collapse
thanks for the advice but i can't seem to install twrp. goomanager is not available for stock éclair/froyo, and without installing any cwm i can't install twrp. also, i tried to install twrp from cm9's cwm, it wrote success but after reboot i still had cwm. WUT

Dummy question: did you try to download another ROM?s zip file ?

Alka-Seltzer PLUS said:
Dummy question: did you try to download another ROM?s zip file ?
Click to expand...
Click to collapse
I tried different nightlies of JB 4.1, 4.2, 4.3, MIUI JB. Also did clean install with 0 success. I'm getting close to the problem, and reached this far:
1.: My CWM (5.x.x.x) does not support the 2nd boot updater script. I don't know how could I upgrade to CWM v6 (seriously, I searched a lot but nothing.)
2.: I can't install TWRP. I mean... Éclair and froyo does not support GooManager to install from an app, and I can only install CWM from 2ndinit.apk. From CWM I install TWRP, it says: "Whoah you are great bro, reboot recovery!" I do that and boom CWM again.
Srsly.: HOW can this happen to me? Other ppl resolved this problem by flashing DFP sbf to their normal Defy (red lens). I won't do that. You know, there must be a way I can install CWM v6 or TWRP. But how? If anyone gives me a solution for my problem which is going on for half a year... I'll get a heart attack I'll be so happy

Uhm.... recently i had to start from SBF and had no problem installing last ( Quarx's ) build of 4.1.2 after having installed the first 2ndinit i downloaded from the web ... so... write exactly your steps ( i know, i know, .. but .... where'R talking through a monitor and misunderstandings are waitnig for us )

Alka-Seltzer PLUS said:
Uhm.... recently i had to start from SBF and had no problem installing last ( Quarx's ) build of 4.1.2 after having installed the first 2ndinit i downloaded from the web ... so... write exactly your steps ( i know, i know, .. but .... where'R talking through a monitor and misunderstandings are waitnig for us )
Click to expand...
Click to collapse
I start from sbf (Froyo). Install 2ndinit apk, install 2ndinit, reboot, wipe data cache dalvik, (try to) install cm10.x > status 0 or status 7
I start from cm9(epsylon build). Reboot into recovery, (try to) install cm10.x > status 0 or status 7
I start from cm9(epsylon build). Reboot into recovery, AROMA Wipe (system, data, cache) into Ext4, (try to) install cm10.x > status 0 or 7
After these, I can't revert to any rom even if i format to ext3 with AROMA Wiper. Cuz' my defy goes soft-bricked and i have to recover it RSD Lite.

Do not reboot after wiping/formatting system. Immediately flash some ROM. Ext3 --> CM7.
Sent from my MB526 using xda app-developers app

gyorgyszemok said:
I start from sbf (Froyo). Install 2ndinit apk, install 2ndinit, reboot, wipe data cache dalvik, (try to) install cm10.x > status 0 or status 7
I start from cm9(epsylon build). Reboot into recovery, (try to) install cm10.x > status 0 or status 7
I start from cm9(epsylon build). Reboot into recovery, AROMA Wipe (system, data, cache) into Ext4, (try to) install cm10.x > status 0 or 7
After these, I can't revert to any rom even if i format to ext3 with AROMA Wiper. Cuz' my defy goes soft-bricked and i have to recover it RSD Lite.
Click to expand...
Click to collapse
No rooting between sbf (Froyo) and installing 2ndinit apk ?

hotdog125 said:
Do not reboot after wiping/formatting system. Immediately flash some ROM. Ext3 --> CM7.
Sent from my MB526 using xda app-developers app
Click to expand...
Click to collapse
Ehm, I didn't reboot after system format, I know that I shouldn't or I get softbricked.

Alka-Seltzer PLUS said:
No rooting between sbf (Froyo) and installing 2ndinit apk ?
Click to expand...
Click to collapse
Yea. It's rooted by default when i flash it....

gyorgyszemok said:
Yea. It's rooted by default when i flash it....
Click to expand...
Click to collapse
I would try to check the md5 at this point

gyorgyszemok said:
Ehm, I didn't reboot after system format, I know that I shouldn't or I get softbricked.
Click to expand...
Click to collapse
I started with sbf, Framaroot, 2ndinit. Then I directly flashed CM10 (9th July) and it flashed successfully. The latest dual recovery has CWMv6, but it's only for CM10 ROMs. Have you tried pre-TWRP builds (maybe the November builds)?
Or maybe, other ROMs like PA, PAC, etc.?

gyorgyszemok said:
Title says it all: I get symlink: some symlinks failed, status 7 error, installation aborted when I try to install Quarx's CM10 (2nd boot). Haven't tried any other JB, since I can't find any that fits. Maybe something with 2nd boot? It seems not to work on my phone...
I tried google-ing the problem, found some information about removing lines from updater-script, but the line was not even there (something with asserts).
Defy red lens MB525
Click to expand...
Click to collapse
Happened to me to before. Try change your kernel. Stock kernel cant flash cm10 and its variant. It'll give status 7 error. When i change to other kernel ex;BL v12 no problem at all.

aiis89 said:
Happened to me to before. Try change your kernel. Stock kernel cant flash cm10 and its variant. It'll give status 7 error. When i change to other kernel ex;BL v12 no problem at all.
Click to expand...
Click to collapse
I forgot to add that my problem got resolved like a month ago.
My main problem was that I couldn't install any JB rom because of status 0, status 7 or bootloop (always), so I went radical:
I flashed DFP231.sbf (for defy plus) on bayer lens defy (MB525!), used Framaroot to root, installed LATEST(!) cwm, and then I could install CM10.x with no problem!

[Q] defy not saving setting fresh install every time after reboot

hi
please can someone help.
I have a Motorola defy mb525 which I have rooted and have 2ndInit bootmenu v2.0 (bootmenu ics recovery v5.6.6-jordan) installed.
I was running cm9 android 4.0.9. and it worked fine.
but I have recently tried to upgrade the phone to cm11 android 4.4.
but the custom recovery boot loader was unable to install cm11. so I tried to upgrade the custom recovery. which messed up my android.
I have put cm9 back on the phone OK. and logged in with all my Google account and started re installing my apps. but got an error saying I was running out of room after installing just one app.
If I restart the phone I loose all my setting and have to set every thing up again. so the phone is not saving the settings. it just starts up like a fresh install every time I start the phone.
I have wiped the cashe partition. run a factory data/reset. and wiped the davik cashe.
and run the safewipe file from this website. but nothing has helped.
I still have the same problem with the phone not saving the setting after rebooting.
if i run the show log command in the bootmenu i get these error messages
cant open mount /cashe/recovery/log
failed to mount /dev/block/mmcb1k1p24 (invaled argument)
cant unlink /cashe/recovery/command
don't know if this is related.
please dose anyone know what I can do to fix it.
Thanks

Convert data and cache to ext3 from boot menu
Or simply flash a sbf, it should also fix the problem
Sent from my MB526 using Tapatalk

thekguy said:
Convert data and cache to ext3 from boot menu
Or simply flash a sbf, it should also fix the problem
Sent from my MB526 using Tapatalk
Click to expand...
Click to collapse
Hi thanks for the response.
I didn't have an option the convert to ext3 in my boot menu.
So I ended up flashing the phone with sbf.
and it all worked fine.
thanks