Soo... I think the USB port on my T-Mobile HD2 is gone. I can feel it jiggle around when I plug in a USB cable... that and nothing happens when I do. No charge, no USB notification, nothing. Not even plugged directly into the power adapter.
My question is whether anyone knows any way to repair the phone for cheap? I've taken the phone to several cell phone repair shops, but no one can do anything without sending it off to HTC. If they do that, then HTC will charge me a crapload because the custom software on the phone somehow must've caused a hardware problem. Because the USB port is broken, I can't flash back to factory, soooo... there's nothing I can do there either.
Any help or advice would be appreciated. Thanks!
My first and only suggestion is to look for the not working phone body of HTC HD2 at ebay.com or similar. If You have some manual skills it wouldn't be so hard to replace it by Yourself. Of cause it is almost open heart surgery but it is possible to do by DIY.
If something like this would happen to me I would do so. You can look for only micro USB port to take it away from other non-working device like old camera or mp3 player or other phone.
Why they decide to use mcroUSB instead much solid miniUSB i don' know.
You can also look for micro USB connector
here
You can put a stock winmo rom (LEOIMG.nbh) on the root of your sd card and boot up into bootloader by holding the volume-down button while booting. Then the bootloader will detect the .nbh and ask you to press a certain button to install it. Then you can send the phone off to htc, it will be completely stock.
-HD2 Android-
huggs said:
You can put a stock winmo rom (LEOIMG.nbh) on the root of your sd card and boot up into bootloader by holding the volume-down button while booting. Then the bootloader will detect the .nbh and ask you to press a certain button to install it. Then you can send the phone off to htc, it will be completely stock.
-HD2 Android-
Click to expand...
Click to collapse
Wish I could, but apparently the cell phone repair shop that tried to fix my phone decided to tell HTC about my custom ROM though he told me he would be doing the repairs (only reason I left the custom ROM on there). But they actually decided to ship it to HTC. HTC decided to record the serial number so I can't send back to them anyways. =/
About the DIY repair. Would it just be a case of re-soldering the USB port back on the phone? Or is it something more technical? I'm asking because the cell phone repair shop I tried out said that they needed to replace that entire board. AFAIK, that board is the mainboard. Doing so would require buying another HD2 body, but I'm afraid that would cost far too much as I am a college student with ridiculous school fees and a very low income.
1: aww dude that sucks, they got you by the serial #
2. I have a broken micro-usb too, saw the disassembly vids, and it looks to me that the m-usb port is attached to the mainboard, and you have to consider too that if you try this as a DIY project, people have had wifi coax become damaged, lcd/digitizer damage, who knows what else from 'professional' repairs, let alone doing it yourself.
2 options, get a card reader and an external hd2 battery charger (and preferably a spare battery), or have the micro-usb port fixed by someone else or by your self.
The external charger and spare battery is cheaper by far, i paid only like $8 for each, and it's surprisingly reliable and practical.
Hope i helped
-HD2 Android-
i would totally call out on that shop and demand they fix it, since they ruined your warranty by sending it off to htc without your consent..
also, search on ebay, theres a cellshop in texas that repairs the port for $50, you mail it to them takes about a day and they mail it right back.
That sucks...I feel like the micro USB on my hd2 is about 2 die...if the phone moves at all connection and charge is lost. why oh why did these bums pick micro USB there's got 2 b a reason
To me is a serious design flaw...I mean its only a matter of time b4 the micro USB will fail on each and every hd2 regardless of how much u baby it device (which most of do)...after a certain number of charges the port goes bust
IMO the micro usbs put 2 much pressure on the port itself it's simply not big enough/solid enough of a connection to support the weight of the wire itself and over time gravity loosens and destroys ur port until u can't even.charge
Sent from my HTC HD2 using XDA App
I agree, the micro-usb is crap. Had my hd2 for like 2 weeks and i broke it by the charge cord getting caught on my foot, sending the phone flying. Luckily, i found that i could get a connection to my comp by holding the cable 'just right', flashed magldr and cwr, and just charge my batteries on the external charger now. I was stuck on the winmo 'test' rom for like 6 months lol.
-HD2 Android-
huggs said:
I agree, the micro-usb is crap. Had my hd2 for like 2 weeks and i broke it by the charge cord getting caught on my foot, sending the phone flying. Luckily, i found that i could get a connection to my comp by holding the cable 'just right', flashed magldr and cwr, and just charge my batteries on the external charger now. I was stuck on the winmo 'test' rom for like 6 months lol.
-HD2 Android-
Click to expand...
Click to collapse
dude same thing happened to me yesterday i was charging my phone and i got up to do something. And the cord caught on my foot and the phone went flying also. and when i tried to charge its like if you move the phone even the slightest it looses connection. But i found a fix that worked for me. im using my external hardrive cord to charge. the connection is a little thicker and fits in there perfectly so now i can move it and it stays connected... Only downside to me is the cord is really short
pyrorob said:
i would totally call out on that shop and demand they fix it, since they ruined your warranty by sending it off to htc without your consent..
also, search on ebay, theres a cellshop in texas that repairs the port for $50, you mail it to them takes about a day and they mail it right back.
Click to expand...
Click to collapse
Yeah, I railed at him for a good 10min in the shop with customers looking (hope I drove away some of his business...). He said that he couldn't fix my phone because I had *illegal software* on it... really? I doubt that a software problem caused the microUSB port to just break off the mainboard.
I've also looked at the disassembly video, and it doesn't seem impossible, but the cost of a micro-usb port is around $35 from what I gather. I think it would take some soldering to replace it, but I have neither a solder nor the experience to attempt it the first time on a $400 device.
I guess I'm stuck with the microSD adapter and external charger for now. ~sigh~ Maybe I'll try another internet-based cell repair shop. Anyone know anything about cellulardr.com? It's based just a couple miles from where I live and they have the part in-stock with a 50% discount that brings the price for repair down to $35 + $35 for parts which is a little high... but if it gets the job done...
I'm a [fraught] example of the result of thinking the usb would somehow last if I was just gentle. Who was I kidding, it was shot to pieces.... I've dropped £100 fixing the phone's screen which resulted in the volume buttons and vibrator dying (I argued till I was blue in the face- before I demanded they reglued the screen back on, a day after it had been 'fixed')... Damn crappy little repair shops, no leg to stand on.
And now I can't charge it.
Waited 2 days for a wall charger (and believe me that was hard as it's my work phone) to find that nomatter how long it's charged for it's dropping from 80% to dead in about an hour no activity.
I wouldn't mind so much but to have finally found a rom I liked, right through from WM to SD android versions to now Cotullas Nand, I'm reluctant to give it up, even though it's more than likely on it's last legs.
Why do phone manufacturers make crakcing phones which **** hardware and builds?
<rant over>
jemma132 said:
Why do phone manufacturers make crakcing phones which **** hardware and builds?
Click to expand...
Click to collapse
You answered that question yourself when you said:
I'm reluctant to give it up, even though it's more than likely on it's last legs.
Click to expand...
Click to collapse
If they made these things more reliable, they'd never have a means to convince you to buy another device .
well a usb port repair is totally possible with just an soldering iron, but you will need a fine tip for that and some flue that does not require cleaning. if any of the contact pad came off you better know where they go or find a way to trace where it goes. if they are broken and you find where they are connected you can use a copper wire taken out from copper brace to bridge them. lastly a broken usb port from the motherboard will never be secure again, so you have to put some padding under it so it will not be moved again; otherwise it will break and may take some contact pad with it in which makes it harder to repair again.
I fixed one of these before with only 1 broken pad that I can trace. so it is definitely possible to be done, but it will be very hard if this is your first time repairing phone. it is possible to rip the volume flex cable like I did. It took me 4 hours to solder flex by rewiring copper wires.
By the way hd2 usb port is only 7$ from eBay.
P.S the good thing about fixing phone is that, I got it from eBay, fix up, and working at $120 XD
Phone going crash
I don't know what happen recently with my phone. It just starting crashing on normal activities. I thought it was probably just the rom, but I flashed HyperDroid GBX v12, clk version and damn....i can't even get pass the boot animation. After a while I did...and then I connected my USB to my computer. Within seconds, phone crashed. I need help. I've task29 this kid like 4 times and then installed clk again.
Sometimes it is just the usb cable quality causing a bad connection... I had this Chinese micro usb data cable and it would only work at a "just right" angle, until I went to Radioshack to buy a 27 $ gold plated usb cable lol
Now everything works good and saved me from having to replace the microusb port on the phone.
Woow I thought I was the only one! I feel all your pains man..
First things first, those of you whose USB is still working, get clockwork mod set up before the USB dies.. at least with a card reader you could still flash thru zips.. I got an external charger and an extra battery as well, now I feel like my hd2 was sorta reborn! Haha..
Dunno bout you guys but I'm starting to feel that our beloved hd2 is slowly being abandoned really sad thing.. and I blame the hardware problems for this trend..
Phugz said:
Dunno bout you guys but I'm starting to feel that our beloved hd2 is slowly being abandoned really sad thing.. and I blame the hardware problems for this trend..
Click to expand...
Click to collapse
Nah, it's just nearing the end of its life cycle. There are better phones coming out now with faster processors and more resources to run bigger software and flashier graphics.
The HD2 has actually stayed on the top of the hill for a surprisingly long time, and in some ways still is.
The biggest difference with the HD2 compared to other phased-out smartphones, I think, is that the HD2 is still very useable even though it is well beyond its originally intended amount of time in the limelight.
I notice this whenever I dig out one of my old devices that I haven't used in a long time, like my Kaiser or Rhodium. They are so slow and basic that they're almost unuseable, where the HD2 is fast, smooth, and seems modern still.
But the mUSB port on these things is ****. Mine's been half-busted for almost a year. I have a wall charger and extra battery, and if I hold the cable just right, I can usually get a connection to the computer, but it's just easier to pop my sd card in one of my old devices to connect to pc and transfer files. The mini-USB ports never gave me near as much trouble as the micro ones, I wish they'd have never switched.
huggs said:
Nah, it's just nearing the end of its life cycle. There are better phones coming out now with faster processors and more resources to run bigger software and flashier graphics.
Click to expand...
Click to collapse
Hi all,
Just thought I'd let you know how I fixed my HD2's loose / non-functioning microUSB port.
I've had similar problems for the last 6 months or so - dodgy microUSB connection resulting in massive amount of fiddling in terms of getting the cable just right, then pretty much completely screwed!
I took receipt of a HTC Sensation a few weeks ago, so decided to spend a little while opening up my now redundant HD2. Dissasembly is pretty easy & self-explanitory, but the leaked videos showing you how to do it is pretty useful. I'm no whizz at these things, but even I managed to do it (mostly) with just a kitchen knife (forgot where I'd put my small screwdrivers, which I eventually found, but everything seemed more dangerous & exciting with the knife).
ANYWAY, I've managed to secure a completely loose microUSB port which means perfect charging & USB connection again. It was incredibly loose & just fell out when I separated the mainboard from the chassis, but I put a bit of rubber I found under it (soldering iron is for pros... I'm winging it here!) & secured the mainboard tightly with screws.
I mean, there's probably a better way to do it, but I couldn't be arsed using any more ingenuity than required... it's a Bank Holiday after all, and the solution seems to have worked pretty damn well.
Cheers,
Dan.
Hi, I can only charge my HTC HD2 phone using the USB port, but I cannot use the usb port for activeSync and USB function (data transfering). I wonder if the USB posrt is dead already?? Why the phone still can be charged via the USB port? Can anyone tell me how to fix this?
Thanks in advance.
mantis123 said:
Hi, I can only charge my HTC HD2 phone using the USB port, but I cannot use the usb port for activeSync and USB function (data transfering). I wonder if the USB posrt is dead already?? Why the phone still can be charged via the USB port? Can anyone tell me how to fix this?
Thanks in advance.
Click to expand...
Click to collapse
I had the same problem last week. My pc couldn't recognize it, but i was able to charge it.. I just took an other usb cable and the problem was solved.
Hi All,
My focus micro USB port stopped working properly, Is there any video/instructions (link) you are aware to replace it ? I dont want to spend a ton of money giving it to service center as I am planning to buy Lumia 920/Samsung Ativ S/HTC 8X
Before you spend money on it, make sure it isn't packed with pocket lint. Mine had some issues where it kept acting like the usb cord was being plugged and removed, making the phone sound for charging over and over. I thought- bad connector. It was stuff down in there, I dug it out with a needle. the debris conducts enough to short the pins just enough to cause problems.
I had looked into the repair, I was looking at $60.
wildbilll said:
I had looked into the repair, I was looking at $60.
Click to expand...
Click to collapse
Add another $60 and you're looking at a new Focus
I've got two Simple Touches with loose charging ports. I was as careful as I could be for years, but eventually the not-very-durable attachments broke and they are unusable.
I've taken one of the Nooks apart, but can't find any numbers on the port or the board, or specs on the details of the port to buy some more. So far the best I've come up with is: Micro USB port type B, female, 5-pin, 4-leg. The pics I've found on these show variability of the leg shape and the spacing, and whether the bevel on the male connector faces up or down relative to the legs.
Can anyone help me with further specs for these ports or where to get them? I've spent hours researching this (right now I have more time than money) and no luck so far. My hope is I can mess around with a friend's hot air soldering station and get at least one of these to work again. And beef up the attachment so it doesn't break again.
Thanks in advance for any help you can offer.
Bake
WWBaker said:
I've got two Simple Touches with loose charging ports. I was as careful as I could be for years, but eventually the not-very-durable attachments broke and they are unusable.
I've taken one of the Nooks apart, but can't find any numbers on the port or the board, or specs on the details of the port to buy some more. So far the best I've come up with is: Micro USB port type B, female, 5-pin, 4-leg. The pics I've found on these show variability of the leg shape and the spacing, and whether the bevel on the male connector faces up or down relative to the legs.
Can anyone help me with further specs for these ports or where to get them? I've spent hours researching this (right now I have more time than money) and no luck so far. My hope is I can mess around with a friend's hot air soldering station and get at least one of these to work again. And beef up the attachment so it doesn't break again.
Thanks in advance for any help you can offer.
QUOTE}
Sorry to hear about your nook problem.
I am not a technician but the micro Usb port is a pretty common one, So I think a common Micro USB port will work
If you can please contact a professional technician .They will do the fix quickly. If not post this in mobileread forum
(http://www.mobileread.com/forums/forumdisplay.php?f=231) The technical genius in here seems to absent
these days.
Check out these ebay links.
http://www.ebay.com/bhp/micro-usb-connector
You can contact the sellers with your orginal port(picture of the port) and get verified. Also check local phone
hardware sellers or even Amazon.com.
Wish you all the best.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
Thanks. I couldn't keep the link I had to the different variations on the 4-leg placement (because I'm new) but I originally had a similar link included. There doesn't seem to be a way to clarify what exactly matches the Nook port except maybe as you say, with ultra close-up pictures. Ebay had a bit more detail in general than Amazon, but still unable to narrow it down sufficiently. There were probably ten different types that were close-but-no-cigar.
I did contact a local cell phone repair place that gets raves for replacing phone ports, but they won't do a Nook, and if it cost more than $20 or 30 wouldn't be worth it. I also have spent hours sifting thru stuff on the mobilereads site (it's how I felt able to take one of the Nooks apart and start messing around) which has some great details, but not this exact one.
Hay, don't be so concerned about this port.
I personally use 3 phones and my sister got 2 phones.
So we use different mini Usb cables to charge or transfer files to our devices.
But we never had problems.
So the lesson is most of the devices use same or identical mini usb ports.
Therefore just use the most common port and just experiment.I know Nook use safty steps to prevent short circuits. So don't be so worried but be careful with the soldering.
(Use the ebay sellers to get the port you want.Most of them are very helpful.)
Best Regards
WWBaker said:
Thanks. I couldn't keep the link I had to the different variations on the 4-leg placement (because I'm new) but I originally had a similar link included. There doesn't seem to be a way to clarify what exactly matches the Nook port except maybe as you say, with ultra close-up pictures. Ebay had a bit more detail in general than Amazon, but still unable to narrow it down sufficiently. There were probably ten different types that were close-but-no-cigar.
I did contact a local cell phone repair place that gets raves for replacing phone ports, but they won't do a Nook, and if it cost more than $20 or 30 wouldn't be worth it. I also have spent hours sifting thru stuff on the mobilereads site (it's how I felt able to take one of the Nooks apart and start messing around) which has some great details, but not this exact one.
Click to expand...
Click to collapse
There is a place in San Diego that advertises NST repairs (among others), including the micro USB port. Obviously they are in the repair business, but you might get lucky if you contact them. Maybe they can give you specs on the port. Heck, since they are in SD, they might even be able to give you a Mouser part number!
Try searching for the connectors on mouser.com or the like. You should be able to get a good description of the dimensions from the datasheets. You can order in quantities as low as one.
Bought a Pro unit a few years about and I had my brother give it to his friend to do the SSD upgrade. Needless to say it never happened and by the time I got it back the HD was missing and and the sata cable is missing. Now since this isn't an off the shelf cable and instead a proprietary cable I cant buy one anywhere. To make matters worse I called Nvidia up and not only do they not sell the parts (understandable) they also don't repair out of warranty units. Which doesn't make any sense. I was trying to get a price quote. I wanna get mine fixed but I don't wanna spend 300 dollars to get a new one.
Sub-Negro said:
Bought a Pro unit a few years about and I had my brother give it to his friend to do the SSD upgrade. Needless to say it never happened and by the time I got it back the HD was missing and and the sata cable is missing. Now since this isn't an off the shelf cable and instead a proprietary cable I cant buy one anywhere. To make matters worse I called Nvidia up and not only do they not sell the parts (understandable) they also don't repair out of warranty units. Which doesn't make any sense. I was trying to get a price quote. I wanna get mine fixed but I don't wanna spend 300 dollars to get a new one.
Click to expand...
Click to collapse
http://www.eevblog.com/forum/reviews/teardown-nvidia-shield-tv/msg944285/#msg944285
jionny said:
http://www.eevblog.com/forum/reviews/teardown-nvidia-shield-tv/msg944285/#msg944285
Click to expand...
Click to collapse
Am I supposed to solder something?
Sub-Negro said:
Am I supposed to solder something?
Click to expand...
Click to collapse
"I connected the SATA solder pads to a SATA connector (taken from an old motherboard) using ~4cm long separated insulated wires without any special measures for high frequency signals (when doing something like this again I was told that twisting the differential pairs wouldn't hurt).
(Sidenote: IMHO soldering things that small is not fun, but I'm not very good at soldering...)"
Yes, you are correct. Very small soldering pads. I'd need a very large stand-alone magnifying lens and at least one steady hand. Two even better.
This phone did, intermittently, work. But it also behaved as though there was a short somewhere in the system. Now it will not power on, and I am making a leap of logic and assuming that's because it cannot charge the battery. (I've tried every single suggestion here re powering it back on, so let's move past that option.)
I note that on ebay and elsewhere there are internal charger port cables (3rd party unfortunately) that are inexpensive (as low as four or five dollars, or eight dollars for one with a small tools set). Has anyone ever used one of those third party internal charger port replacements and had success?
Thanks in advance.
Okay, I have gone ahead and ordered one of the internal USB ribbon assemblies for my OnePlus 2. But I haven't seen anyone else discuss having actually done a change-out of this part. Isn't there any hardy soul armed with spudger and screw driver who's attempted this?
shonkin said:
Okay, I have gone ahead and ordered one of the internal USB ribbon assemblies for my OnePlus 2. But I haven't seen anyone else discuss having actually done a change-out of this part. Isn't there any hardy soul armed with spudger and screw driver who's attempted this?
Click to expand...
Click to collapse
i replaced the charging cable it is easy quick fix, ordered one from aliexpress
arjan.bongers said:
i replaced the charging cable it is easy quick fix, ordered one from aliexpress
Click to expand...
Click to collapse
If you don't mind me asking, did the phone work at all right before the replacement? Mine is a dead as a doornail, which is why I wonder. The fix does look to be easy (I watched some videos and even removed the old one, so the new install is all ready to go).
shonkin said:
If you don't mind me asking, did the phone work at all right before the replacement? Mine is a dead as a doornail, which is why I wonder. The fix does look to be easy (I watched some videos and even removed the old one, so the new install is all ready to go).
Click to expand...
Click to collapse
He didnt charge thats why i replaced the connector. but the rest of the functions were normal
arjan.bongers said:
He didnt charge thats why i replaced the connector. but the rest of the functions were normal
Click to expand...
Click to collapse
Well, we shall see if that solves my completely non-functioning phone issues or not. Perhaps this thing is just dead. My ebay seller is behind schedule as far as delivery goes, but again I will post here whatever the outcome once I do replace the usb port and ribbon.
I did promise to post a video of my install. I do not know if this worked yet (charging a newer battery; if that doesn't work I'll go back to the old battery and try again). But here is the video, which I ended up sorta having fun doing.
https://www.youtube.com/watch?v=INZUBsXXTFE
Well, I'm marking this down as a fail. The install was easy, but the phone remains dead, dead, dead. Not a whiff of life to it. The short, if it is a short as I suspect, may be in either the motherboard or daughterboard. So, not being one easily driven off by failure, I bought a working but very bent up OP2 off ebay for 70 bucks. The idea being to take its innards out and put them into the frame (and the I think working screen) of the one I have. I'll look either brilliant or the fool (I play the second one better). I will, as usual, report back.
So... said I'd follow up on the $70 ebay phone buy (the phone very bent up but somehow still working). I did get it, tested it (it did work but screen was under obvious pressure due to bend), then removed the motherboard, usb ribbon cable, and daughterboard from it and moved them into the non-working phone I was given by a friend. And it worked!! I now have a OnePlus 2 phone which is updating the rom at this moment. I'll probably root it and put a custom rom on later, but for now I just wanna see what the phone is like with the standard setup. Anyway.... it was fun to take a phone apart (2 phones, actually) and succeed at the end.