ADB install - Nook Touch General

I managed to install the drivers but how do I open the shell? I want to access some lost files.
I followed the instructions but adb_usb.ini was nowhere to be found so I had to create it.
I have to control ADB via cmd.exe right? Anyone can guide me?

http://forum.xda-developers.com/wiki/BN_Nook_Simple_Touch/Installing_ADB
http://forum.xda-developers.com/wiki/Android_Debug_Bridge
Ok, to get to a shell on the Nook you have to use a shell on the host computer.
In Windows, a shell is known as cmd.exe, "MS-DOS Prompt" or command.
That's the (by default) black window with text.
You can start a Windows shell through the Program list if a shortcut already exists.
If not, you can start it by holding down the Windows key, hitting "R" and typing cmd.exe in the box.
The little box is in a sense already a shell, but it makes a bigger looking shell.
The program adb.exe is the one that you will run to interact with your Nook.
You will have to either be in the same directory as where adb.exe or else have that directory in your PATH.
There are a bunch of commands that you can use (documented in the second link above).
You must first tell ADB how to connect to your device through either a "connect" (for WiFi) or "usb".
Once you are connected you can issue the other commands.
Code:
adb shell
This will let your Windows shell access a shell on your Nook.
Since this is an entirely different system, the commands are different.
In Windows, to list files you type "dir", in Linux (the basis of Android), you type "ls".

I can get to the directory of adb.exe on command.
I don't get it what am I supposed to do next.
If I run adb.exe it starts to load something and then nothing. The Nook is connected, it has Noogie as it's CWR.
After running adb.exe what do I do? Do I go to the nook directory or something? The thing is that I don't even know if I'm running ADB correctly. I followed everything on the wiki

vdguzman said:
it has Noogie as it's CWR.
Click to expand...
Click to collapse
Um, Clockwork Recovery and Noogie are two separate and unrelated things.
Code:
C:\>adb usb
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
At that point it will either say that it found a USB device or that it didn't.
If it's connected, you can type "adb shell".
On Windows, when you click on the USB icon on the taskbar it will list what is connected.
Normally with CWR you should see two lines, USB Mass Storage and ADB.

Related

How to make adb work?

I've searched a lot, but did not find a solution.
When I connect my HTC Kaiser with Android Ion 1.5 on the top to my Linux box (all UDEV settings are as recommended), the adb utility (launched as root) does not recognize it correctly. It shows a set of questionmarks instead of the device name:
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
???????????? device
adb basic commands (pull/push/install/shell) work, though, but DDMS does not work and I can't debug my application when the device is attached.
Does somebody have a solution?
You need to run the adb server as root. Use su or sudo to run these:
Code:
./adb kill-server
./adb start-server
You can then use adb and ddms as a normal user. If you use fastboot, you may find you need to run that as root as well.
it is root
Super Jamie said:
You need to run the adb server as root. Use su or sudo to run these:
Code:
./adb kill-server
./adb start-server
You can then use adb and ddms as a normal user. If you use fastboot, you may find you need to run that as root as well.
Click to expand...
Click to collapse
Like I mentioned in my question - I do run adb as root.
When it's launched not as root, I can not even do "adb shell" and
"adb devices" shows:
"????????????? Permission denied". So, it is root, I assure.
BTW, on my work Windows 2k3 machine I can use ddms, but
"adb devices" still shows some garbage letters instead of the device name.
Sorry for my English, if my explanation is not clear.

Set up/run adb on a MAC

Can someone please help me, or point me in the right direction on how to setup and run simple commands through adb on a MAC? Yes, I've used the search, and yes I've searched all over the internet but I still cannot figure it out. Sorry for my stupidity lol
But any help would be greatly appreciated, thank you
Perhaps you could say a few words about what you have tried already and where you are stopped.
I'm assuming you've downloaded and installed the Mac version of the SDK, yes?
On the phone, you need to turn on Settings -> Applications -> Development -> USB debugging (and may as well check "Stay awake", too).
I don't have a OS/X box, but on Linux you need to perform the *first* adb command as root... the first time an "adb" command is run (after a reboot) it starts up an adb-server process, and that needs to be priviliged enough to write to USB. (After that, you can run adb commands as any user, since those commands "talk" to the adb-server on your Mac, which in turn talks to the phone over the USB cable.)
bftb0
Go to developer. android. com/sdk/index.html (take out the spaces - I still can't post links for some reason) and download the Android SDK for Mac. That same page also includes directions on how to get started with installation. You'll be using the Terminal within Mac OS X for ADB commands, so I would recommend getting comfortable with Terminal before jumping into the SDK. Unfortunately, you'll have to look this up because I couldn't even begin to explain everything, nor do I have the time. Hope the rest helps, though.
bftb0 said:
Perhaps you could say a few words about what you have tried already and where you are stopped.
I'm assuming you've downloaded and installed the Mac version of the SDK, yes?
On the phone, you need to turn on Settings -> Applications -> Development -> USB debugging (and may as well check "Stay awake", too).
I don't have a OS/X box, but on Linux you need to perform the *first* adb command as root... the first time an "adb" command is run (after a reboot) it starts up an adb-server process, and that needs to be priviliged enough to write to USB. (After that, you can run adb commands as any user, since those commands "talk" to the adb-server on your Mac, which in turn talks to the phone over the USB cable.)
bftb0
Click to expand...
Click to collapse
Yes I've downloaded and installed the sdk, turned debugging on and now im trying to flash the recovery image onto my phone and that is where im lost at because I don't know exactly what to do
Los-O said:
Yes I've downloaded and installed the sdk, turned debugging on and now im trying to flash the recovery image onto my phone and that is where im lost at because I don't know exactly what to do
Click to expand...
Click to collapse
Note that what you are asking (now) is completely different than what you asked about in your OP - in fact, OS X is immaterial, really, in light of what you just indicated. That suggests that you are in a hurry... if that is the case, I recommend you spend a couple days reading before you rush off and do something you might regret. It is evident from your response that you really have not been reading the threads here with much diligence.
If you are trying to flash a recovery image, that implies that your phone is already rooted; either that what you are trying it isn't going to work - you have to have a rooted phone to begin with before you flash a custom recovery image. At the moment, you can root your Eris only if it has a 1.5 (1.16.605.1 or 1.17.605.1) official Verizon/HTC release on it. This has been described if not a hundred times in the threads here, at least tens of times - you need to read some more.
Nevertheless, if you want to rush into something, here is a step by step set of instructions which was current a couple of days ago. I won't vouch for it being 100% up to date with the latest and greatest images (either ROM or recovery), but it completely describes the process involved.
Stock 1.5 --> Root (2.1) install --> Custom Recovery install -> recovery to custom ROM 0.3. That's what is working at the moment.
bftb0
bftb0 said:
Note that what you are asking (now) is completely different than what you asked about in your OP - in fact, OS X is immaterial, really, in light of what you just indicated. That suggests that you are in a hurry... if that is the case, I recommend you spend a couple days reading before you rush off and do something you might regret. It is evident from your response that you really have not been reading the threads here with much diligence.
If you are trying to flash a recovery image, that implies that your phone is already rooted; either that what you are trying it isn't going to work - you have to have a rooted phone to begin with before you flash a custom recovery image. At the moment, you can root your Eris only if it has a 1.5 (1.16.605.1 or 1.17.605.1) official Verizon/HTC release on it. This has been described if not a hundred times in the threads here, at least tens of times - you need to read some more.
Stock 1.5 --> Root (2.1) install --> Custom Recovery install -> recovery to custom ROM 0.3. That's what is working at the moment.
bftb0
Click to expand...
Click to collapse
I've already rooted my phone
Los-O said:
I've already rooted my phone
Click to expand...
Click to collapse
Well, then you should be on your way; the instructions for what you are trying to attempt are in that link I provided for you in answer to your question (which you purposely redacted when you quoted my post).
I understand that it's your first post, and I should give some leeway for that reason alone, especially since you might have gotten root without ever having used "adb" or "fastboot". (PB00IMG.ZIP method).
On the other hand, I think you can see my point. Please try to avoid wasting other people's time by providing them useful & relevant details of your situation so they can give you good answers. And reading some of the links adjacent to your own post which actually give exactly the details you are asking for might be a good idea, too.
You wanted to know "What are the directions to DisneyWorld?", but instead asked "How do I put gas in my car?" - when you already knew exactly how to do that. But don't take my word for it - reread your first post for yourself - it actually says nothing about what you are trying to do.
I don't know, maybe I got this all wrong, and you still don't have your phone talking to your OS X machine correctly with adb, and that's the source of the trouble. But then, there would be no way to know one way or another - you haven't really said.
bftb0
Download the android sdk and run this automator script.
20 Questions
Los-O:
You said "any help would be greatly appreciated." Maybe that will also include help from the surly folks, such as me.
You said you have "downloaded and installed the SDK". Let's start there. (Also, note that the Android SDK for Mac OS X is only for x86 Apple machines - stop right here if you are using an older PPC based OS X machine).
The Mac SDK is in a .zip file. I presume that means that you unzipped it somewhere on your hard drive, and that you can remember what the folder name/directory name is where you unpacked all those files. (From where I sit, that could mean that you used a GUI based tool, or something from the command line to unpack the files; but I am guessing.)
Here is a flowchart to help you with the steps.
(1) Have you successfully run the "adb" command from within a Terminal window? (Yes: goto (4), No: Continue)
(2) Do you know how to open a Terminal window in OS X? (Yes: goto (4), No: Continue)
(3) Have a look at this information about Terminal on OS X, and then
(4) Start a Terminal window up.
(5) When you type the command (followed by hitting the Enter key):
Code:
adb --help
at the command line, do you get a pageful of information about the adb command, or an error such as "command not found"? (Help Info: goto step (7), No: Continue)
(6) Add to your PATH the location of the SDK tools (including "adb"). For this step, you need to recall where you unpacked your .zip file. On my Linux box, the "adb" command (and others) are located in the folder at
/opt/android/android-sdk_r05-linux_86/tools/
where the part "/opt/android/" is the folder I unzipped them in. For OS X, surely the next folder name in the path is something other than "android-sdk-linux_86" - just poke around in whatever OS X uses as a file browser, and look for the "tools" folder underneath where you unpacked the files. Once you have done that, you should be able to type the full "path" to that (tools) folder in a command.
Let's suppose that the complete path to that "tools" folder looks something like this:
/HardDrive1/foo/bar/android-sdk_r05-mac_86/tools
Then, for example, we would add this to the current terminal (shell) PATH using the following command:
Code:
export PATH=${PATH}:/HardDrive1/foo/bar/android-sdk_r05-mac_86/tools
Obviously, you would change the part "HardDrive...86" so it matches the complete path to the "tools" folder in the SDK which you unpacked onto your machine.
You can inspect the value of PATH for correctness by typing the command
Code:
echo $PATH
Now, go back to step (5) and keep at steps 5-6 until you are able to run the "adb --help" command successfully - that is, get it to print some help information. Don't close this Terminal window after you have the PATH set correctly - we are going to use it shortly.***
(7) Plug the phone into the USB cable and the USB cable into the computer
(8) On the phone, make sure that Settings -> Applications -> Development -> USB debugging is toggled on.
(9) In the terminal window from step (6), type the commands
Code:
adb kill-server
adb devices
You will see one of three things at this point after the "adb devices" command executes:
A. (this is what we want to see)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
HT9ABCDnnnnn device
If you see this, very good: adb has detected your phone and talked to it; continue to step # (10).
B. (not good - you probably need to run adb as the root user)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
???????????? no permissions
In this case, the "adb" command ran, and detected the presence of the phone, but does not have sufficient privileges to write to the USB device; whether or not this happens in a given flavor or Unix (e.g. OS X) depends on what user and group permissions are set on the device, and which "groups" regular users are in. Not having OS X in front of me, I can not predict; but the solution in this case is to run the command as the root user.
It is my impression that OS X has the "sudo" command for this purpose (read here); if that is the case, then you might want to run the commands
Code:
adb kill-server
sudo `which adb` devices
If sudo is not available to you, or not setup correctly, you might have to read this Apple Technical Note, or this one, or this one
C. (some other problem - no USB device is detected)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
Your on your own for this one - consult your local Apple OS X expert!
(10) Now you are ready to communicate with the phone using "adb" commands.
Note that running the "adb" command for the first time after your OS X machine is booted up creates a long lived adb "server" process. (You might see it in a "ps" command listing as "adb fork-server"). That process is what actually communicates with the phone. Any subsequent "adb" command first communicates with that "adb server" on your OS X machine, and then the server communicates with the phone.
Sometimes it goes stale or gets cranky after unplugging the phone too many times. Simply re-start if you want by doing a "adb kill-server" (any user can do this), followed by any adb command, keeping in mind the results from step # (9) above.
OK, whew! The desired goal was to get a recovery image loaded on to the Eris after it had been rooted - it is time to do that, as adb is working now.
See the Instructions by GrdLock here, in the section entitled "II. Installing Amon's recovery image"
bftb0
***The setting of the PATH when you use the Terminal app using the directions given in step # (6) only last for the life of a single Terminal session. If you want to make this change in such a way that it will be already set up every time you open a new Terminal window, you need to do this by editing a file in your home folder - either ".bash_profile" or ".bashrc" . (Different files names are used depending on which "shell" is used). Setting this up is an exercise left up to the interested reader.
Once you have the android sdk unzipped, add the full path to the android tools directory to your path.
I just added the path to my .bash_profile.
For me it looks like this:
export ANDROID-SDK=/Users/Aaron/android-sdk/
export PATH=$ANDROID-SDK/toolsATH
Then I save and close my bash_profile and run the command, from the terminal:
source .bash_profile
This reloads the bash_profile into the shell. Then cd to your android tools directory. Once you get into the tools directory type the command adb. If everything is correct you should see a help menu spit out to the console.
If you need help with your bash_profile a simple google search will help you out.
hey bftb0,
just wanted to chime in and say thanks for that step-by-step. been wrestling with the same issues as the original poster and your walk through got it going. thanks for being patient.
taocow
bftb0,
thank you so so soo much for that last post, I think i've finally figured it out. and also thank you for your patience, i wish i could buy you a coke or something lol
taocow said:
hey bftb0,
just wanted to chime in and say thanks for that step-by-step. been wrestling with the same issues as the original poster and your walk through got it going. thanks for being patient.
taocow
Click to expand...
Click to collapse
los-O said:
bftb0,
thank you so so soo much for that last post, I think i've finally figured it out. and also thank you for your patience, i wish i could buy you a coke or something lol
Click to expand...
Click to collapse
taocow / los-O
Did you need to run the first "adb" command as root with "sudo" ? Let me know - and also mention the version of OS X that you are using; maybe it will help other Mac users if they read this thread. (I got the impression from reading a little bit that different releases of OS X might handle "sudo" a little differently - or have different device permissions for regular users.)
Also, in reviewing this thread, I have to say ... I acted like an a$$. And I should know better, I did IT for a while. If there is one thing I learned about dealing with people and computers, it's that it is extremely easy for a misunderstanding to occur, and especially if you are helping someone out over the phone or via mail/forum. Please accept my apologies.
bftb0
bftb0 said:
taocow / los-O
Did you need to run the first "adb" command as root with "sudo" ? Let me know - and also mention the version of OS X that you are using; maybe it will help other Mac users if they read this thread. (I got the impression from reading a little bit that different releases of OS X might handle "sudo" a little differently - or have different device permissions for regular users.)
Also, in reviewing this thread, I have to say ... I acted like an a$$. And I should know better, I did IT for a while. If there is one thing I learned about dealing with people and computers, it's that it is extremely easy for a misunderstanding to occur, and especially if you are helping someone out over the phone or via mail/forum. Please accept my apologies.
bftb0
Click to expand...
Click to collapse
also now im able to install the recovery (thanks to you) but when i try and push the recovery and flash images i get
"cannot stat 'recovery.img': No such file or directory" same for the flash image
but i put the files in the tools folder like the guide said to do...?
also im on OS X 10.6.2, but no i didnt have to use the "sudo" thing you were talking about, the "adb devices" command worked the first try. and dont worry about it, i understand where you were coming from. but apology accepted, though
Los-O said:
also now im able to install the recovery (thanks to you) but when i try and push the recovery and flash images i get "cannot stat 'recovery.img': No such file or directory" same for the flash image but i put the files in the tools folder like the guide said to do...?
Click to expand...
Click to collapse
That sounds like you are referring to the files by name, but they are not in the current directory where you are running the fastboot command.
The "pwd" command (Print Working Directory) tells you what your current directory is.
The "cd folder-path" command (Change Directory) allows you to change the Terminal/Shell's idea of where the "current directory" is.
The idea behind the PATH variable is that it is a searchable list (separated by ':' colon characters), so that you can be in a given directory with the files you want to manipulate, but the commands you use are in other directories. When you start a command by typing its' name, the Terminal/Shell app walks through that list of folders in PATH (from left to right in order), looking for that program by name.
That means that if you want to run a program ("proggie") that opens a file ("myfile") that is in the current directory you might type the command.
$ proggie myfile
(or $ proggie ./myfile )
... and as long as "proggie" was in one of the folders listed in your PATH, it would run, and find your file "myfile".
But, there is no requirement that you be in the same directory with your files, or the program that you are running (for instance "fastboot"). In those cases, you need to explicitly specify the complete path to your files or programs, so they can be found. For instance:
$ proggie /users/los-o/mystuff/project3/myfile
or, if "proggie" was not in a folder in your PATH, but you knew that it was located in /opt/tools, you could type the command
$ /opt/tools/proggie myfile
If your current directory contains the file "myfile", or
$ /opt/tools/proggie /users/los-o/mystuff/project/myfile.
Same deal with fastboot - you give it the name of the recovery file as the 3rd argument on the "command line"
$ fastboot flash recovery name-of-my-copy-of-the-recovery-file.img
bftb0
*Whew!* Ok thanks again bftb0 for all the help, I think im finally starting to get the hang of this adb stuff
u have a knack for teaching
bftb0 said:
Los-O:
You said "any help would be greatly appreciated." Maybe that will also include help from the surly folks, such as me.
You said you have "downloaded and installed the SDK". Let's start there. (Also, note that the Android SDK for Mac OS X is only for x86 Apple machines - stop right here if you are using an older PPC based OS X machine).
The Mac SDK is in a .zip file. I presume that means that you unzipped it somewhere on your hard drive, and that you can remember what the folder name/directory name is where you unpacked all those files. (From where I sit, that could mean that you used a GUI based tool, or something from the command line to unpack the files; but I am guessing.)
Here is a flowchart to help you with the steps.
(1) Have you successfully run the "adb" command from within a Terminal window? (Yes: goto (4), No: Continue)
(2) Do you know how to open a Terminal window in OS X? (Yes: goto (4), No: Continue)
(3) Have a look at this information about Terminal on OS X, and then
(4) Start a Terminal window up.
(5) When you type the command (followed by hitting the Enter key):
Code:
adb --help
at the command line, do you get a pageful of information about the adb command, or an error such as "command not found"? (Help Info: goto step (7), No: Continue)
(6) Add to your PATH the location of the SDK tools (including "adb"). For this step, you need to recall where you unpacked your .zip file. On my Linux box, the "adb" command (and others) are located in the folder at
/opt/android/android-sdk_r05-linux_86/tools/
where the part "/opt/android/" is the folder I unzipped them in. For OS X, surely the next folder name in the path is something other than "android-sdk-linux_86" - just poke around in whatever OS X uses as a file browser, and look for the "tools" folder underneath where you unpacked the files. Once you have done that, you should be able to type the full "path" to that (tools) folder in a command.
Let's suppose that the complete path to that "tools" folder looks something like this:
/HardDrive1/foo/bar/android-sdk_r05-mac_86/tools
Then, for example, we would add this to the current terminal (shell) PATH using the following command:
Code:
export PATH=${PATH}:/HardDrive1/foo/bar/android-sdk_r05-mac_86/tools
Obviously, you would change the part "HardDrive...86" so it matches the complete path to the "tools" folder in the SDK which you unpacked onto your machine.
You can inspect the value of PATH for correctness by typing the command
Code:
echo $PATH
Now, go back to step (5) and keep at steps 5-6 until you are able to run the "adb --help" command successfully - that is, get it to print some help information. Don't close this Terminal window after you have the PATH set correctly - we are going to use it shortly.***
(7) Plug the phone into the USB cable and the USB cable into the computer
(8) On the phone, make sure that Settings -> Applications -> Development -> USB debugging is toggled on.
(9) In the terminal window from step (6), type the commands
Code:
adb kill-server
adb devices
You will see one of three things at this point after the "adb devices" command executes:
A. (this is what we want to see)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
HT9ABCDnnnnn device
If you see this, very good: adb has detected your phone and talked to it; continue to step # (10).
B. (not good - you probably need to run adb as the root user)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
???????????? no permissions
In this case, the "adb" command ran, and detected the presence of the phone, but does not have sufficient privileges to write to the USB device; whether or not this happens in a given flavor or Unix (e.g. OS X) depends on what user and group permissions are set on the device, and which "groups" regular users are in. Not having OS X in front of me, I can not predict; but the solution in this case is to run the command as the root user.
It is my impression that OS X has the "sudo" command for this purpose (read here); if that is the case, then you might want to run the commands
Code:
adb kill-server
sudo `which adb` devices
If sudo is not available to you, or not setup correctly, you might have to read this Apple Technical Note, or this one, or this one
C. (some other problem - no USB device is detected)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
Your on your own for this one - consult your local Apple OS X expert!
(10) Now you are ready to communicate with the phone using "adb" commands.
Note that running the "adb" command for the first time after your OS X machine is booted up creates a long lived adb "server" process. (You might see it in a "ps" command listing as "adb fork-server"). That process is what actually communicates with the phone. Any subsequent "adb" command first communicates with that "adb server" on your OS X machine, and then the server communicates with the phone.
Sometimes it goes stale or gets cranky after unplugging the phone too many times. Simply re-start if you want by doing a "adb kill-server" (any user can do this), followed by any adb command, keeping in mind the results from step # (9) above.
OK, whew! The desired goal was to get a recovery image loaded on to the Eris after it had been rooted - it is time to do that, as adb is working now.
See the Instructions by GrdLock here, in the section entitled "II. Installing Amon's recovery image"
bftb0
***The setting of the PATH when you use the Terminal app using the directions given in step # (6) only last for the life of a single Terminal session. If you want to make this change in such a way that it will be already set up every time you open a new Terminal window, you need to do this by editing a file in your home folder - either ".bash_profile" or ".bashrc" . (Different files names are used depending on which "shell" is used). Setting this up is an exercise left up to the interested reader.
Click to expand...
Click to collapse
excellent post...very helpful
Los-O said:
Can someone please help me, or point me in the right direction on how to setup and run simple commands through adb on a MAC? Yes, I've used the search, and yes I've searched all over the internet but I still cannot figure it out. Sorry for my stupidity lol
But any help would be greatly appreciated, thank you
Click to expand...
Click to collapse
I do everything on a Mac, so I would be the guy to ask. How far did you get? Have you unzipped the sdk to a folder?
Basically the difference between mac and others is that when others do a command like adb, we have to do ./adb This is true for other commands too. It's easy once you get used to it.
bftb0,
Thanks so much! Step 6 solved my problem
Thank you!!
bftb0 said:
Los-O:
You said "any help would be greatly appreciated." Maybe that will also include help from the surly folks, such as me.
You said you have "downloaded and installed the SDK". Let's start there. (Also, note that the Android SDK for Mac OS X is only for x86 Apple machines - stop right here if you are using an older PPC based OS X machine).
The Mac SDK is in a .zip file. I presume that means that you unzipped it somewhere on your hard drive, and that you can remember what the folder name/directory name is where you unpacked all those files. (From where I sit, that could mean that you used a GUI based tool, or something from the command line to unpack the files; but I am guessing.)
Here is a flowchart to help you with the steps.
(1) Have you successfully run the "adb" command from within a Terminal window? (Yes: goto (4), No: Continue)
(2) Do you know how to open a Terminal window in OS X? (Yes: goto (4), No: Continue)
(3) Have a look at this information about Terminal on OS X, and then
(4) Start a Terminal window up.
(5) When you type the command (followed by hitting the Enter key):
Code:
adb --help
at the command line, do you get a pageful of information about the adb command, or an error such as "command not found"? (Help Info: goto step (7), No: Continue)
(6) Add to your PATH the location of the SDK tools (including "adb"). For this step, you need to recall where you unpacked your .zip file. On my Linux box, the "adb" command (and others) are located in the folder at
/opt/android/android-sdk_r05-linux_86/tools/
where the part "/opt/android/" is the folder I unzipped them in. For OS X, surely the next folder name in the path is something other than "android-sdk-linux_86" - just poke around in whatever OS X uses as a file browser, and look for the "tools" folder underneath where you unpacked the files. Once you have done that, you should be able to type the full "path" to that (tools) folder in a command.
Let's suppose that the complete path to that "tools" folder looks something like this:
/HardDrive1/foo/bar/android-sdk_r05-mac_86/tools
Then, for example, we would add this to the current terminal (shell) PATH using the following command:
Code:
export PATH=${PATH}:/HardDrive1/foo/bar/android-sdk_r05-mac_86/tools
Obviously, you would change the part "HardDrive...86" so it matches the complete path to the "tools" folder in the SDK which you unpacked onto your machine.
You can inspect the value of PATH for correctness by typing the command
Code:
echo $PATH
Now, go back to step (5) and keep at steps 5-6 until you are able to run the "adb --help" command successfully - that is, get it to print some help information. Don't close this Terminal window after you have the PATH set correctly - we are going to use it shortly.***
(7) Plug the phone into the USB cable and the USB cable into the computer
(8) On the phone, make sure that Settings -> Applications -> Development -> USB debugging is toggled on.
(9) In the terminal window from step (6), type the commands
Code:
adb kill-server
adb devices
You will see one of three things at this point after the "adb devices" command executes:
A. (this is what we want to see)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
HT9ABCDnnnnn device
If you see this, very good: adb has detected your phone and talked to it; continue to step # (10).
B. (not good - you probably need to run adb as the root user)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
???????????? no permissions
In this case, the "adb" command ran, and detected the presence of the phone, but does not have sufficient privileges to write to the USB device; whether or not this happens in a given flavor or Unix (e.g. OS X) depends on what user and group permissions are set on the device, and which "groups" regular users are in. Not having OS X in front of me, I can not predict; but the solution in this case is to run the command as the root user.
It is my impression that OS X has the "sudo" command for this purpose (read here); if that is the case, then you might want to run the commands
Code:
adb kill-server
sudo `which adb` devices
If sudo is not available to you, or not setup correctly, you might have to read this Apple Technical Note, or this one, or this one
C. (some other problem - no USB device is detected)
Code:
* daemon not running. starting it now *
* daemon started successfully *
List of devices attached
Your on your own for this one - consult your local Apple OS X expert!
(10) Now you are ready to communicate with the phone using "adb" commands.
Note that running the "adb" command for the first time after your OS X machine is booted up creates a long lived adb "server" process. (You might see it in a "ps" command listing as "adb fork-server"). That process is what actually communicates with the phone. Any subsequent "adb" command first communicates with that "adb server" on your OS X machine, and then the server communicates with the phone.
Sometimes it goes stale or gets cranky after unplugging the phone too many times. Simply re-start if you want by doing a "adb kill-server" (any user can do this), followed by any adb command, keeping in mind the results from step # (9) above.
OK, whew! The desired goal was to get a recovery image loaded on to the Eris after it had been rooted - it is time to do that, as adb is working now.
See the Instructions by GrdLock here, in the section entitled "II. Installing Amon's recovery image"
bftb0
***The setting of the PATH when you use the Terminal app using the directions given in step # (6) only last for the life of a single Terminal session. If you want to make this change in such a way that it will be already set up every time you open a new Terminal window, you need to do this by editing a file in your home folder - either ".bash_profile" or ".bashrc" . (Different files names are used depending on which "shell" is used). Setting this up is an exercise left up to the interested reader.
Click to expand...
Click to collapse
Wow what a straightforward guide to helping me get this set up!! A million thanks! I don't even have an Eris, but what model of the phone you have is irrevelant to this guide...
Thanks again!!

adb remount operation not permitted

Hey Guys,
I Clockwork3'd my Aria, but I wanted to update my sources (thread 730398) so I can get non market apps. When I follow the instructions in that post I get an error:
Code:
./adb remount
remount failed: operation not permitted
'adb devices' does show my Aria's SN, I'm su'd and I'm running in debug mode. I also chowned everything in the android sdk tools and its subdirectories.
Here's the question -
In searching, I found (thread 614645) that suggested ro.secure wasn't set properly, and sure enough if I do:
Code:
./adb shell
$ getprop ro.secure
1
$
Shouldn't applying clockwork have set that properly? Would the instructions at (thread 8041739 post 9 ) be the right steps to resolve this on an Aria?
Thanks!
PS - sorry I can't post direct links.
if you have all the drivers installed, it should work...
which OS are you using?? (Mac, Win7, etc)
dont rund SDK command in Clockwork, with phone on connect data cable and select "charge only" when asked.
the ./ command is used for Linux i think, i never got that command to work either. just go to the folder where SDK/Tools is located in CMD prompt or Terminal(depending on the OS) and run the following command:
adb remount
hope this helps a bit
I had a lot of issues with driver installs on Windows 7, so I'm doing this on a netbook with Ubuntu netbook remix. Also tried the reflash CD, similar issue.
Right, so with Ubuntu, and the cable my phone came with (have tried a few others just in case)
1. phone on and operational
2. plug in to laptop
3. phone gives happy USB connected and Charge Only notifications
4. fire up terminal window, and su
5. type ./adb remount
and I get the error above. If I do kill-server to refresh it, I get the demon starting successfully on port 5037.
Yeah, I was hoping I'd just missed something stupid. Should I need to modify the boot.img file outside of what Clockwork did?
My symptoms match those described in thread 685146 post #3, however, I've only applied Clockwork (which seems to work) not done anything else funky.
I have my windows 7 machine at the same point now -
adb remount gives 'remount failed: operation not permitted'
and
getprop ro.secure at the adb shell returns 1.
I think this means there's something wrong on the phone, if both machines act the same.
One other data point, I noticed the new Superuser Permissions app that installing clockwork gave me is asking to give superuser permissions to /system/bin/sh when I try to run the adb shell, but it doesn't trigger that when I do the adb remount.
Not sure what this means, any ideas most welcome - TIA!
steps here fixed it, thanks - http://forum.xda-developers.com/showthread.php?t=730398

feeling like a serious noob today--ADB linux help

ok well i've been using adb for a while now via windows on our desktop, my laptop however runs ubuntu. but i've run into a problem.....I CAN'T OPEN ADB IN LINUX! using terminal i navigate to the proper location then i initiate adb shell but i get an error saying the command doesn't exist...what am i doing wrong?
tried ./adb ?
if you haven't added ADB to path it won't be recognized as a command, then you'd have to execute it using ./adb
Hi, adb
is located in <android-sdk-folder>/platform-tools folder. You could add it into your $PATH variable in .bashrc . Than it's ready to use from anywhere

[Q] Mac OSX - ADB - List of devices attached Blank

I am running on a Mac (OSX Lion) and have installed android-sdk-macosx.
I am trying to connect to a Kindle Fire 6.2.2
However, this is as far as I can get:
Code:
bash-3.2# ./adb devices
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
List of devices attached
bash-3.2#
As you can see, no devices show up.
I have tried switching cables, USB ports, reboot the device and my machine... banging my head against the wall.
Nothing works.
I have read about 29 pages of posts through this forum, and Googled it.
No dice.
Any suggestions?
would not use the sdk at all - if you use the mac/linux version of kfu you save a lot of time and space - you don't need to use kfu if you don't like to - but all commands you'll ever need are in the tools folder of kfu - it also includes drivers and setup scripts - maybe give it a try:
http://forum.xda-developers.com/showpost.php?p=21369040&postcount=653
mkdir ~/.android
echo 0x1949 >> ~/.android/adb_usb.ini
ADB needs this entry to see the Kindle Fire no matter what OS you're on.
right - there is also a installation script for this included in the pack - install.sh if i remember right
took the advice above and it's still not working for me. i have the same exact problem. when i try to run install_drivers.sh i get:
cp: drivers/adb_usb.ini: No such file or directory
Done!
logout
[Process completed]
When I run KFU i get:
/Users/donaldclark/kfu/run.sh: line 84: seq: command not found
please help
as far as i know (don't own a mac) you have to call the commands with
./ from terminal window - eg ./run.sh
I also got the same error message at line 84 running the install script in OSX 10.6.8
-E
it's from eratosthene - give him a pm - i'm shure he can help you
http://forum.xda-developers.com/member.php?u=1616763
Try remove the usb driver from your device and re-install gain.
I use Kindle_Fire_Utility_MacLinux_0.9.2 3 with adb.mac
and its located right inside my root directory (not under users) step before.
I went to the files and I opened file called
install_drivers.sh
I did deleted everything behind -p and just dragged
the adb_usb.ini (its located in drivers) into that install_drivers.sh script and I hit save.
thats how it looks like
mkdir -p /Kindle_Fire_Utility_MacLinux_0.9.2 3/drivers/adb_usb.ini/adb_usb.ini
Than I just run adb.mac and all is operational
my kindle was rooted with burittoroot2
If you need those files send me a pm I have them in my dropbox.
somboonr said:
Try remove the usb driver from your device and re-install gain.
Click to expand...
Click to collapse
there is no uninstalling drivers like in windows.
line 84 SOLUTION
Incarnate609 said:
took the advice above and it's still not working for me. i have the same exact problem. when i try to run install_drivers.sh i get:
cp: drivers/adb_usb.ini: No such file or directory
Done!
logout
[Process completed]
When I run KFU i get:
/Users/donaldclark/kfu/run.sh: line 84: seq: command not found
please help
Click to expand...
Click to collapse
Regarding the "run.sh: line 84: seq: command not found", I found out that the "seq" command is not recognized with MAC OS... so I did a search and replace, replacing "seq" with "jot -". Now it works.
Reference: Search google for seq and mac
What worked for me.
I had the same problem after updated the sdk on my MacBook Mac OSX 10.6.8
cd to the tools directory (where android program is located)
run:
./android update usb
./android update adb
then edit the ~/.android/adb_usb.ini file and add 0x1949 as the last line (your previous adb_usb.ini file is overwritten by the above commands).

Categories

Resources