Database Users

Pocket Hack Master XDA II mini Result

the following result are done with
Pocket Hack master 2004 3.05.001
Spb Benchmark 1.1.0 B40
Torrance (%) 0.55 1.02 0.13 0
SPB B SPB % CPU Index CPU %
Default 1210.33 100 1597.07 100
Dynamic (max 416) 1226.75 102 1573.02 99
208 870.17 72 1095.37 69
416 1201.09 100 1601.87 101
468 1356.75 113 1813.79 114
520 1515.54 126 2016.91 127
for OC to 520 Mhz approx. 26% imporve on system performance and 27% CPU Index
Hope useful.

How about underclock the procesor for decrese battery consumption? ...is it stable at 520mhz?
Regards,
P.C.
p.s. Great job!

Very stable so far.. will do battery test soon. but it take a long time to do so.

i wrote it on another post a few days ago.. but u can go higher than 530Mhz if u add new speeds in the manual settings - my jam reported it was stable at 600 and something... even 845Mhz worked!

The speed of CPU can show upto 1040 at 130 Mhz Bus speed.
but the MIPS rate won't change above 520 this means above 520
the CPU will ignore the freq multi and lock to 4x which is 520Mhz

What probability I have to "burn" my JAM procesor? :?: ...I don`t know a lot of PDA-s...but I do know about computers...is there the same thing?...the battery consumptions should increase...what about the heat?.... :roll:
Regards,
Primoz

PCAIOO said:
The speed of CPU can show upto 1040 at 130 Mhz Bus speed.
but the MIPS rate won't change above 520 this means above 520
the CPU will ignore the freq multi and lock to 4x which is 520Mhz
Click to expand...
Click to collapse
oh ok.. thanks for the info

Undervolting Thread

This thread has been created to share Undervolting Settings (UV).
Undervolting makes CPU/GPU/Modem to consume less power, thus extend battery life. This is allowed by flashing modified kernels that allow UV (Thanks to raspdeep's work). One can use Voltage Control to change settings (Thanks to xan).
Setting format is -x mV for a given CPU clock as used in xan's app: [1200Mhz] [1000Mhz] [800Mhz] [400Mhz] [200Mhz] [100Mhz]
What are your settings?
PS: Please edit your very first post with settings instead of reposting. Thank you!

Stable: 50 50 75 100 100 100
1200 max: 50
1000 max: 50
800 max: 75

I am currently running 50 50 50 75 100 100 with no stability problems. It has made 4 back-to-back quadrant runs and a couple days of general usage without any crashes so far.

Undervolting doesn't work well with my phone the same with overclocking. I can't undervolt 1000Mhz and above because it causes much stability issues here. I can only undervolt 100-800Mhz with settings < 100mV.

TheVisitorX said:
Undervolting doesn't work well with my phone the same with overclocking. I can't undervolt 1000Mhz and above because it causes much stability issues here. I can only undervolt 100-800Mhz with settings < 100mV.
Click to expand...
Click to collapse
My system hangs in sleep mode when I have setCPU or Superpower with sidekick on.

I have the max cpu capped at 800mhz using SetCpu.
Undervolted -50 for 800mhz 600 400 200 and 100 each.Phone was at 50% last night and 6 hours later it's dead.Battery was completely discharged.All i did was set everything at 50Mvs less.Correct ? i think i'm missing something.Do help.thanks.

hey guys
im new to oc and uv
im currenlty using ramads gb jvh with hardcores speedmod kernel
ive got tegraks ultimate app and have oc'd it to 1100 as anything above reboots my phone
everything else is the same as standard
i was wondering if anyone else can help me with what i should change
i have no clue,
so far
frequency 1100
core 1275mv
internel 1100
cpu level 1
frequency 800
core 1200
internel 1100
cpu level 2
frequency 400
core 1050
internal 1100
cpu level 3
frequency 200
core 950
internal 1100
cpu level 4
frequency 100
core 950
internal 1000
these values are all stock, i havent touched them
im wanting to know what i should change them to
thanks
forgot to add, my battery life is really bad, i use hsdpa and wifi frequently

i have cm7 #19 with the (latest) glitch v10b-VC kernel..no oc, bu uv
100mhz -50,200mhz -50,400mhz -50, 800mhz -25 and 1000mhz @stock

What is the negative effects of UV?
My current values starting at 1000mhz is:
-75
-100
-100
-125
-175

hackeron said:
What is the negative effects of UV?
My current values starting at 1000mhz is:
-75
-100
-100
-125
-175
Click to expand...
Click to collapse
Negative effects come in the form of stability issues and random reboots. Is doesn't physically damage the processor. By lowering the core voltage supplied to the CPU, you also decrease the noise margin for the CPU to properly differentiate between logic 1 and logic 0. This is why -75, for example, works for some and not for others because processors are not 100% identical. The obvious benefit UV is lower power consumption.

gtda said:
hey guys
im new to oc and uv
im currenlty using ramads gb jvh with hardcores speedmod kernel
ive got tegraks ultimate app and have oc'd it to 1100 as anything above reboots my phone
everything else is the same as standard
i was wondering if anyone else can help me with what i should change
i have no clue,
so far
frequency 1100
core 1275mv
internel 1100
cpu level 1
frequency 800
core 1200
internel 1100
cpu level 2
frequency 400
core 1050
internal 1100
cpu level 3
frequency 200
core 950
internal 1100
cpu level 4
frequency 100
core 950
internal 1000
these values are all stock, i havent touched them
im wanting to know what i should change them to
thanks
forgot to add, my battery life is really bad, i use hsdpa and wifi frequently
Click to expand...
Click to collapse
I'm also using Tegrak's overclock apk for some time now (from beginning) and it's really good!
Just lower the core voltage (start with cpu level 0) until it's unstable (random reboots), then add a few mv (+5) to make it stable again (no reboots). do this for every core frequency (only one at the time, so you know witch one is making the system unstable). I never touch the internal frequency... Undervolting will NOT damage your CPU (overclocking can if you're not carefull)
Don't be stupid testing just a few hours, test (stress test) for days. Only then you are sure it's stable
These are my settings:
(rock stable after a few weeks => playing asphalt6, running quadrant and smartbench hours a day for a few weeks,...)
cpu level 0
frequency 1000
core 1205mv (-70) => could get it stable at 1200 but had one reboot after one week, so I added +5
internel 1100
cpu level 1
frequency 800
core 1105 (-95) => could get it stable at 1100 but had one reboot after one week, so I added +5
internel 1100
cpu level 2
frequency 400
core 950 (-100)
internal 1100
cpu level 3
frequency 200
core 825 (-125)
internal 1100
cpu level 4
frequency 100
core 825 (-125)
internal 1100
Now I know what my lowest core voltage is, I can start overclocking (not for now).
I'm on stock deodexed JVP 2.3.4 with Hardcore (latest) Speedmod (partition EXT4), Tegrack Overclock Ultimate and Voodoo Control Plus (holy combo => Quadrant 2400+ (no OC, just UV) and wow, what a great battery life!
edit: yes, I need to update my signature

SamHaLeKe said:
cpu level 4
frequency 100
core 825 (-125)
internal 1100
Click to expand...
Click to collapse
^ Typo??????????
internal voltage @ 100Mhz is 1000mV by default, so you are overvolting.

kiwijunglist said:
^ Typo??????????
internal voltage @ 100Mhz is 1000mV by default, so you are overvolting.
Click to expand...
Click to collapse
Default value is 950mV on my phone according to pimpmycpu. According to SamHaLeKe's post, he's reducing his by -125 so 825mV is correct
I'm new to UV, and just experimenting. My current values are
1200 = -50mV
800 = -50mV
400 = -100mV
200 = -100mV
100 = -150mV
Seems ok so far, more aggressive cutting gave me reboots

$$$

The most i could get from my phone w/o stability issues
1500 - 50
1400 - 50
1300 - 50
1200 - 50
1000 - 50
800 - 75
400 - 100
200 - 125
100 - 150

Starting from 1000MHz, I'm using these values :
-50 [1000]
-75 [800]
-100 [400]
-125 [200]
-150 [100]
No stability issues since then !

Mine are;
1000 : 50
800 : 50
400 : 75
200 : 75
100 : 100
Works great for me
Sent from my GT-I9000 using Tapatalk

swaakx said:
Starting from 1000MHz, I'm using these values :
-50 [1000]
-75 [800]
-100 [400]
-125 [200]
-150 [100]
No stability issues since then !
Click to expand...
Click to collapse
i have the same!
my phone now cold as ice. and greatly stable

I'm a noob at this UV stuff but I'm quite interesting about that.
I tried with Control Freak, should I set first a low voltage on 100Mhz and try to stress the cpu only with this change on 100MHZ? or should I set all voltages and test?
thx for help

i'm on jvq darkyrom
using tegrak overclock ultimate
1200mhz 1255 (-20)
800mhz 1105 (-95)
400mhz 950 (-100)
200mhz 850 (-100)
100mhz 810 (-140)

[Research]Mhz vs Quadscore/LinPack #Update

Mhz vs Quadscore on [beta] desire hd2 #Update
hey here same interesting tests i did
if i locked my phone in power saving mode u get
CPU and Score
Mhz ScoreA CPU Mem IOps Linpack
256Mhz 900 1750 525 1600 11
384Mhz 1050 2580 618 2000 16
460Mhz 1350 3000 990 2600 19
500Mhz 1600 3250 1050 2800 20
768Mhz 2200 4600 1120 3500 29
1000Mhz 2500 5400 1120 4150 35.5
1200Mhz 2700 6200 1120 4380 40
maybe there could be another mode that will use
500mhz most of the time [for normal using or one app using Cpu]
and when playing or using heavy 1000Mhz
[Dev]
i see that memory score is not linear
maybe could fixed by our greatest devers

I hope u do understand that these results are total bullcrap.
The newest dual core chips dont even get 2.7k scores in that benchmark.
Something in the desire HD build farks up the scores simple as that.

If you look at the quadrant advanced score, you'll notice it only gets those scores because of the I/O score. The processor one is about the same or a little more than teh Nexux 2.2, so if you underclock to 500 mhz you may get a total of 1600, but your processor score will suck badly and your phone will lag and really suck.
Keep your max at 998 and your min at 245 and use smartass and you should be fine.

orangekid said:
If you look at the quadrant advanced score, you'll notice it only gets those scores because of the I/O score. The processor one is about the same or a little more than teh Nexux 2.2, so if you underclock to 500 mhz you may get a total of 1600mhz, but your processor score will suck badly and your phone will lag and really suck.
Keep your max at 998 and your min at 245 and use smartass and you should be fine.
Click to expand...
Click to collapse
Agree.
Sent from my HTC HD2

orangekid said:
Keep your max at 998 and your min at 245 and use smartass and you should be fine.
Click to expand...
Click to collapse
+1 for this.
My HD2 has been running smoothly with 245-998MHz smartass for weeks now, battery life has been great too.

i update it with more info check post1
i see that memory score is not linear
maybe could fixed by our greatest devers

Quadrant scores are useless. RUn it, then run it again, you'll get different results.
I don't use SetCPU at all, it's just not needed.

According to my Quad Test im getting a total of 2196 with 245-998mhz with smartass on SetCPU my CPU: 4450 Mem: 1127 I/O: 4716 2D: 273 3D: 412 Work that one out

[Q] Perfect overclock config @ 1.2 ghz defy

Yeah am new To xda and i want to overclock my defy @ 1.2 ghz ... and whenever
i try to overclock above 1000 mhz it starts heating upto 43 degrees... plz give me the overclocking values @ stable ... and is this overheating do serious damage to phones hardware!.....! thanks

My setting :
300 Mhz / 30 Vsel
600 Mhz / 42 Vsel
800 Mhz /50 Vsel or 900 Mhz / 54 Vsel
1.0 Ghz / 58 Vsel or 1.2 Ghz / 66 Vsel
You can use this setting without any risk. 1.2 Ghz is the original value of OMAP 3630 on Droid2.
But i think you have another problem on your phone (something running) to get 43° for your battery. Mine is allways between 30° and 37° max running at 1.2 GHZ...
Note : original Defy+ settings = 300/33 ; 600/48 ; 800/58 ; 1000/68

devilthehellraiser said:
Yeah am new To xda and i want to overclock my defy @ 1.2 ghz ... and whenever
i try to overclock above 1000 mhz it starts heating upto 43 degrees... plz give me the overclocking values @ stable ... and is this overheating do serious damage to phones hardware!.....! thanks
Click to expand...
Click to collapse
300mhz @ 26Vsel
600mhz @ 38Vsel
1200 mhz @ 58 Vsel

what vsel do u use for 1ghz?
For 1.2ghz try using a low vsel and test if it works. Keep increasing it by 1 until it is stable.
For my phone the minimum it could handle wihtout crashing immediately is 56. Its pretty stable at 58 and for games or if i need more stability i try to raise it to 60-64. But it starts heating faster

i use 48 for 1 ghz its rock stable as it never crashed ...

minez - 320 at 17 ,,, 650 at 38 ,,, 1.2GHz at 60 ..... very stable

Mine is:
[email protected]
[email protected]
[email protected]
very stable and not too much heating

Mine is
22 300mhz
32 600mhz
52 1ghz
Been using them settings for many months

devilthehellraiser said:
Yeah am new To xda and i want to overclock my defy @ 1.2 ghz ... and whenever
i try to overclock above 1000 mhz it starts heating upto 43 degrees... plz give me the overclocking values @ stable ... and is this overheating do serious damage to phones hardware!.....! thanks
Click to expand...
Click to collapse
Do you really need 1.2ghz? Don't set high frecuencies if you dont need it.
Anyway, dont worry too much about temp. I'm on a hot country, and when i'm heavy using my defy, temp raises to 45C, no problem.
All android phones have automatic cooling mode when you reach critic temps. You dont have to worry about that.
Sent from my MB525 using XDA App

my settings are:
[email protected]
[email protected]
[email protected]
i could lower each setting with 2 vsel and still get a stable phone, but i increased it just in case. and yeah, you dont need 1.2GHz, 1GHz will do just fine, dont worry.

My settings are:
[email protected]
[email protected]
[email protected]
1.2ghz is awesome and what it supposed to be

Just stumbled across this thread, wanting to test 1.2ghz and was wondering what app you guys are using to monitor temperatures? is set cpu good enough?

dude i use battery xl and it displays temp in the notifications !

My settings are:
[email protected]
[email protected]
[email protected]
greetings!

Com4nd3r said:
My settings are:
[email protected]
[email protected]
[email protected]
greetings!
Click to expand...
Click to collapse
These settings seem to be the most stable ive tried so far on my defy, and temp is very cool at 27 degrees. Thanks
I do suppose it depends on your phone i had 2 zte blades and one of the them was stable at 826mhz but the other would not go above 710mhz without constant reboots
Wait until we get unlocked boot loader that is when the overclocking gets serious XD my nexus is at 1.2ghz with smartassV2 govenor and its rock stable, saying that with unlocked bootloader the potential is endless like with my xperia arc it has qualcomm snapdragon msm8255 @ 1ghz but with DooMLoRD's kernel can have a max of 1.9ghz But then again i hate my xperia arc lol

furrabbit.nh said:
These settings seem to be the most stable ive tried so far on my defy, and temp is very cool at 27 degrees. Thanks
I do suppose it depends on your phone i had 2 zte blades and one of the them was stable at 826mhz but the other would not go above 710mhz without constant reboots
Wait until we get unlocked boot loader that is when the overclocking gets serious XD my nexus is at 1.2ghz with smartassV2 govenor and its rock stable, saying that with unlocked bootloader the potential is endless like with my xperia arc it has qualcomm snapdragon msm8255 @ 1ghz but with DooMLoRD's kernel can have a max of 1.9ghz But then again i hate my xperia arc lol
Click to expand...
Click to collapse
not every cpu is identical , thats why not every phone can reach the same clock rates. To avoid damaging your cpu , its important not to set the vsel too high.
On my defy i never had it set over 65vsel.
70vsel is the max. limit so ive heard.
when yous settings are unstabile you could either clock down or set your vsel higher.

I AM USING [ROM]Android 2.3.6 - 4.5.2-109_DHT-25(mod. "spear1403")
I CHANGE A VERY FEW VALUES FROM: RECOVERY, SYSTEM, OVERLOCK. AND MY PHONE GONE SLOW, LIMPACK SHOW ME: 4 MFLOP!!!
SOME ONE TRY THIS?

1.2 GHz!!! the battery drains very fast or not?

My Defy is stable with:
vsel1: 25 vsel @ 0330 mhz
vsel2: 38 vsel @ 0800 mhz
vsel3: 51 vsel @ 1200 mhz
vsel4: 62 vsel @ 1400 mhz
The Defy of my GF crashes with these settings...
she uses:
vsel1: 31 vsel @ 0330 mhz
vsel2: 41 vsel @ 0800 mhz
vsel3: 58 vsel @ 1000 mhz
vsel4: 64 vsel @ 1200 mhz
EDIT: I need 1400 mhz to play GTAIII lagfree also lot of stuff like Skype calling / Fritz Fon / PhotoShop Express are working better on 1400 than on 1000, I don't understand why everybody says we do not need more than 1000, also the battery drain is about the vsel and not the frequency. My battery lasts loger on 62 vsel @ 1400 than on 64 vsel @ 1200

I am reading the posts in XDA about changing the default frequency of processor in DEFY as I am a beginner of CPU overclock, would like to ask for advice:
1. What is "vsel"? Is it the voltage set for the processor to run in certain frequency?
2. What is the default "vsel" for DEFY in 800MHz? I guess it is 58, right?
Correct me if I am wrong. Thanks a lot!

Vsel settings, please advice

Hi
Running quarx's cmx 1708, gb kernel, and incredibly pleased!
However I would very much appreciate some help with the vsel settings.
There are 4 levels. Default though seems to be three, 300, 600 and 1000 mHz.
Can anyone advice me how to configure the cpu settings for good performance and very good battery life (don't want my defy downgraded to a portable Commodore 64, but battery life is more important than performance)
My current settings are
300 @ 17
600 @ 32
1100 @ 57
1200 @ 62.
Don't know why though
swajpat på min gelebönade defy!

The settings are fine I guess. Just added the above frequencies in VSel Calculator. It gives the same recommended vsels.

henkaoh said:
Hi
Running quarx's cmx 1708, gb kernel, and incredibly pleased!
However I would very much appreciate some help with the vsel settings.
There are 4 levels. Default though seems to be three, 300, 600 and 1000 mHz.
Can anyone advice me how to configure the cpu settings for good performance and very good battery life (don't want my defy downgraded to a portable Commodore 64, but battery life is more important than performance)
My current settings are
300 @ 17
600 @ 32
1100 @ 57
1200 @ 62.
Don't know why though
swajpat på min gelebönade defy!
Click to expand...
Click to collapse
check this out.. You'll get the idea.. Rest give it a try for yourself..
SetVsel settings thread

henkaoh said:
Hi
Running quarx's cmx 1708, gb kernel, and incredibly pleased!
However I would very much appreciate some help with the vsel settings.
There are 4 levels. Default though seems to be three, 300, 600 and 1000 mHz.
Can anyone advice me how to configure the cpu settings for good performance and very good battery life (don't want my defy downgraded to a portable Commodore 64, but battery life is more important than performance)
My current settings are
300 @ 17
600 @ 32
1100 @ 57
1200 @ 62.
Don't know why though
swajpat på min gelebönade defy!
Click to expand...
Click to collapse
Iv had issues with wake , general lags on screen-on with 300Mhz @17 ,
18 / 21 seems rock soild though

Please ask all questions in Q&A. Thread moved there.

TeeJay3800 said:
Please ask all questions in Q&A. Thread moved there.
Click to expand...
Click to collapse
60 @ 1300