Database Users

I think I bricked my nexus (my fault) please help!

Hello all,
I think I may have bricked my nexus one. It is completely my fault for attempting things that I knew little about, so flame away But after the flaming, if anyone is willing to help I would be sooooo thankfull...
I successfully rooted my phone following the instructions on this page: (all links edited with a double asterisk as I don't believe I can post links)
h**p://theunlockr.com/2010/01/02/how-to-root-the-nexus-one/
Then successfully installed cyanogenmod (which is awesome!) following this page:
h**p://theunlockr.com/2010/01/08/how-to-load-a-custom-rom-on-the-nexus-one/
All was well, I even got the modaco desire rom up and running, and was happily switching back and forth using the recovery screen. I had nand backups for specific setups, etc.
Then I decided it would be good to know how to go back to stock, and found this page:
h**p://**w.androidspin.com/2010/05/06/guide-unrooting-your-nexus-one-its-like-it-never-happened-almost/
I followed the instructions to the letter (I think) except for erasing userdata (it said "failed: remote not allowed"). I thought that things would be ok, since I'd recently wiped, so I followed the page till the end.
The phone rebooted, and I got the original nexus boot animation - but it's in an endless loop! What's worse, it that now when I try to go to the bootloader or recovery mode, I get the exclamation triangle with the little android.
Is there any way through a command prompt (or other method) that I can fix this? I tried to re-flash the RA recovery image through the command prompt, but the response was, "waiting for device."
ANYTHING that anyone can suggest to help, I would be so thankful! I've been loving the nexus, and hate to think that I crippled it
Thanks in advance,
Randy

I doubt its bricked.
Noticed you didnt mention that fast boot doesnt work? (power button+trackball) try it.
Once you get to fastboot you can flash any ROM back. (fastboot flash **** commands from a command shell)

Did you ever perform a Nand Backup from Recovery?

It's not bricked, the only way to brick is to interrupt power when flashing a Radio image

Connect phone to PC. Open command prompt.
adb reboot recovery
Wipe, reflash.

So far, nobody has managed to brick a Nexus. There is no way as the fastboot mode can restore the whole phone and can't be messed with. Make sure you have the latest version of the SDK with correct USB drivers and fastboot. Then try and reflash the recovery image.
-------------------------------------
Sent from my Nexus One

nexus5894 said:
So far, nobody has managed to brick a Nexus. There is no way as the fastboot mode can restore the whole phone and can't be messed with. Make sure you have the latest version of the SDK with correct USB drivers and fastboot. Then try and reflash the recovery image.
-------------------------------------
Sent from my Nexus One
Click to expand...
Click to collapse
Actually...
http://forum.xda-developers.com/showpost.php?p=6320068&postcount=404

Paul22000 said:
Actually...
http://forum.xda-developers.com/showpost.php?p=6320068&postcount=404
Click to expand...
Click to collapse
............................

It worked!!!!!
It worked!!
britoso, thank you soooooo much! The only way that I knew to get into bootloader/recovery was via power button/volume down, but power/trackball brought up the bootloader screen, and I clicked on fastboot. I was able to flash the RA recover image through the command terminal via fastboot, then able to get into recovery. I had cyan and modaco sense on the sd, and was able to flash one of them on.
​
I never thought I'd be so happy to see "quietly brilliant"!!! I WILL buy you a beer, a case in fact as soon as money clears my paypal account.
I have learned my lesson, research research research. (I did do some, but not enough to feel comfortable with what I was doing - hence my cry for help!)
Other than the phone and OS itself, the thing I like most about the nexus is the fact that one CAN root, and then customize (sold a Telus moto droid because I could not do that very thing).
I digress... thanks again so much!
And Paul, thanks for your sense ROM; I've had HTC phones from the Touch to the the diamond to the Hero, and missed the UI!

Randy Malkoski said:
It worked!!
britoso, thank you soooooo much! The only way that I knew to get into bootloader/recovery was via power button/volume down, but power/trackball brought up the bootloader screen, and I clicked on fastboot. I was able to flash the RA recover image through the command terminal via fastboot, then able to get into recovery. I had cyan and modaco sense on the sd, and was able to flash one of them on.
​
I never thought I'd be so happy to see "quietly brilliant"!!! I WILL buy you a beer, a case in fact as soon as money clears my paypal account.
I have learned my lesson, research research research. (I did do some, but not enough to feel comfortable with what I was doing - hence my cry for help!)
Other than the phone and OS itself, the thing I like most about the nexus is the fact that one CAN root, and then customize (sold a Telus moto droid because I could not do that very thing).
I digress... thanks again so much!
And Paul, thanks for your sense ROM; I've had HTC phones from the Touch to the the diamond to the Hero, and missed the UI!
Click to expand...
Click to collapse
Glad to hear it. You learn the most by trial and error.

I think i got the same problem. i tried to Unlock Bootloader and Root Google Nexus One which was successful but then i tried to superboot it and when it came to the part where you "double click the ‘install-superboot-windows.bat’ file" i clicked it but it did not go to the nnext screen where the superboot completes it just stayed at the "bootloader screen". i must hve not done something or done something wrong i dont know.
So then i unplugged the phone from the pc and rebooted it. when it reeboted i wasnt getting any network, the phone was slow and the notification bar would not slide down...also i noticed the phone restarting on itself...
/i tried all kinds of "restore to factory settings" but not solved. Can anyone tell me what to do tht will work. I coud not understand what was said in the above thread as i am new to this android n my first time rooting n stuff n i believe that solution would work for me too..if some one could please explain in simple tirms the steps i need to take would be good...
Really appreciate it....

revonomics said:
I think i got the same problem. i tried to Unlock Bootloader and Root Google Nexus One which was successful but then i tried to superboot it and when it came to the part where you "double click the ‘install-superboot-windows.bat’ file" i clicked it but it did not go to the nnext screen where the superboot completes it just stayed at the "bootloader screen". i must hve not done something or done something wrong i dont know.
So then i unplugged the phone from the pc and rebooted it. when it reeboted i wasnt getting any network, the phone was slow and the notification bar would not slide down...also i noticed the phone restarting on itself...
/i tried all kinds of "restore to factory settings" but not solved. Can anyone tell me what to do tht will work. I coud not understand what was said in the above thread as i am new to this android n my first time rooting n stuff n i believe that solution would work for me too..if some one could please explain in simple tirms the steps i need to take would be good...
Really appreciate it....
Click to expand...
Click to collapse
Tell me what i need to download again and how to go about it...i really need my phone working again ((((

[Q] Xoom files doesnt change

Hello guys,
i got a serious and frustrating problem here.
A few days ago my xoom was stuck on the M screen, so I used a thread in the forum and recovered it.
It solved myh problem back then, but since I had 3.2 before this and the solution injected me with Android 3.01 my problems started to show themselves.
the first one is that
<b> Through Fastboot, RecoveryMod, ADB </b> and any other way you can Imagine to install a new ROM or even remove or create a file,
All of them show success message but when I check them out I see no changes.
i tried fastboot and Recovery to install nearly every ROM,Recovery and bootimage in this site but so far it was wild goose chase.
so I want to ask if I'm doing anything wrong or if you need any more information here, but please help me with this

wow I cant believe it, All these masterminds here and no answer to my distress signal??
Guys I am so in trouble and this is the only place I hoped to get answered.
I can provide you with more info if you need, but please dont say I'm on my own here.
all these years this forum was the last hope for me.
i know I'll get my answer here one day

You are not being very clear about what you have done,, but I'm assuming that you reinstalled the stock image that got you back to HC 3.01. Can you see if you are able to get OTA updates to get you back to at least 3.1, or 3.2 if possible?

If that's my problem forgive me please, Ive written that post in 3:00AM
for the sake of clearity I should add some info:
1. I even tried stock ROMs but you see I cant even flash them (Not from Recovery nor Fastboot) the steps seem successful : it opens the package,it installs them and it says everything was a success. But when I restart the device I see nothing has changed.
2. OTA updates are the same, they keep downloading and when the sysem reboots to recovery to install them it cant find them.
3. You dont believe it if I say even files and programs that I remove from device by my hand(Android OS) are back after the first restart.
And you see it's dark magic! everything from a file to a partition are back by one reboot. I dont know what should I call it but I havent seen anything like it on the whole Internet.
So seems like I should make a competition for the xda experts here
Can you publish it so all of them can see it?

Mohfath said:
If that's my problem forgive me please, Ive written that post in 3:00AM
for the sake of clearity I should add some info:
1. I even tried stock ROMs but you see I cant even flash them (Not from Recovery nor Fastboot) the steps seem successful : it opens the package,it installs them and it says everything was a success. But when I restart the device I see nothing has changed.
2. OTA updates are the same, they keep downloading and when the sysem reboots to recovery to install them it cant find them.
3. You dont believe it if I say even files and programs that I remove from device by my hand(Android OS) are back after the first restart.
And you see it's dark magic! everything from a file to a partition are back by one reboot. I dont know what should I call it but I havent seen anything like it on the whole Internet.
So seems like I should make a competition for the xda experts here
Can you publish it so all of them can see it?
Click to expand...
Click to collapse
Actually, I have seen someone with the same problem here on this forum, but I can't recall exactly what the solution was.
Can you describe, step by step what you are doing, what cable you are connecting to your pc with, etc?

okantomi said:
Actually, I have seen someone with the same problem here on this forum, but I can't recall exactly what the solution was.
Can you describe, step by step what you are doing, what cable you are connecting to your pc with, etc?
Click to expand...
Click to collapse
That would be relief to know this could be solvable.
I will look more too.
As for your post I must say:
1. I plug the Xoom to the PC using the included cable
2. I start the xoom and start fastboot
3. on the PC system has the drivers and completely knows it
4. I start with SDK:
I. Fastboot oem unlock (Completing onscreen instructions and reboot device)
II. Fastboot mode again I use Fastboot flash boot boot.img
III. Continuing with Recovery,System
IV. Rebooting the device anything is the same.
My ROM is unchanged by the process and keeeeeeeeps giving the damn error of System process error please submit
5. And with ClockworkrecoveryMod I have the stock ROM on my sd card.
I. I choose install zip from sd card.
II.Choose the correct zip file and start flashing.
III. Choosing Wipe Data/Factory reset will take the device into a complete hang. unless I first use the mount page to mount the System/Data
IV. I reboot the device and ..... you know nothing changed.
so thats my story.
Still hope to find something about it.

Thanks...that was helpful. But now I want to know the following:
Were you rooted before the trouble started?
What did you do to recover?
If rooted, what version of CWM recovery did you have installed? Did you do a nanadroid backup? (I guess the answer is no, because you could have just restored with that).
What recovery are you accessing when trying to flash a zip file?
If you can answer these questions I will continue to wrack my brain trying to recall where I saw that thread.
Edit: please check out this thread http://forum.xda-developers.com/showthread.php?t=1370312
Some of what I said to him may help you .

okantomi said:
Were you rooted before the trouble started?
What did you do to recover?
If rooted, what version of CWM recovery did you have installed? Did you do a nanadroid backup? (I guess the answer is no, because you could have just restored with that).
What recovery are you accessing when trying to flash a zip file?
If you can answer these questions I will continue to wrack my brain trying to recall where I saw that thread.
Edit: please check out this thread http://forum.xda-developers.com/showthread.php?t=1370312
Some of what I said to him may help you .
Click to expand...
Click to collapse
Being rooted? -> Yes, The world is more beautiful with root!
to recover -> I followed this: http://forum.xda-developers.com/showthread.php?t=1097997 Shame it was Android 3.0
I use ClockworkRecovery 3.0.0.28 and I cant upgrade it cause of ... you know
And for your help I must say you are definitely the most caring person I know...
I'm off to check the provided link now

I was thinking of something that might be a reason.
I have this tiny problem:
When I go to CWM and choose Erase userData/Factory Reset Device Hangs
Click to expand...
Click to collapse
I was thinking of may be the userdata partition is corrupted and I gotta find a way to flash it completely.
Somehow I used Fastboot utility to do this and after saying Success, Nothing changed again.
Do you know any other way to physically do this job?

Broken touch screen, need to get Stock

The touchscreen on my Fire stopped working today. I already talked to Amazon and am getting a replacement, but I want to revert back to stock before sending it in. I've seen ways to do this with TWRP, but I don't have a touchscreen to use TWRP, or any recovery for that matter, with.
Is there any way to do this?
I do have full ADB and Fastboot access, with FireFireFire working, but do not have a currently working rom installed (I was on CM9, and it won't go past the boot screen).

drk.hd said:
The touchscreen on my Fire stopped working today. I already talked to Amazon and am getting a replacement, but I want to revert back to stock before sending it in. I've seen ways to do this with TWRP, but I don't have a touchscreen to use TWRP, or any recovery for that matter, with.
Is there any way to do this?
I do have full ADB and Fastboot access, with FireFireFire working, but do not have a currently working rom installed (I was on CM9, and it won't go past the boot screen).
Click to expand...
Click to collapse
There is a way to do this with adb... I just do not know the proper commands. Sorry

Does installing a custom rom void the warranty? Seems like it would be BS for Amazon not to honor it when it's apparently a hardware related issue.

sengwall said:
Does installing a custom rom void the warranty? Seems like it would be BS for Amazon not to honor it when it's apparently a hardware related issue.
Click to expand...
Click to collapse
No, I don't think it does, but I'd rather not take the chance.

drk.hd said:
No, I don't think it does, but I'd rather not take the chance.
Click to expand...
Click to collapse
YES! It absolutely does. The second the device was rooted it broke warranty.
Sent from my myTouch_4G_Slide using XDA App

The same thing actually happened to me earlier today. I was just browsing some sites on the ICS rom when it just stopped responding. I couldn't get it to recognize any touches even after a bunch of reboots, so I just figured it to be some bug that hadn't been squashed yet. When I dropped down to recovery and saw the same issue, I knew I had a real problem.
Hoping against hope, I tried both CWMR and TWRP on it and got no results. Like you, I figured it would have to go back to Amazon, so I started searching for a way to get it back to stock... nothing obvious jumped out at me because everything is written with access to recovery in mind... which doesn't help.
So, I started reading about adb and going through the built-in help. As I was familiarizing myself with some basic adb commands and options, I left TWRP open in front of me. I don't know how long I had it that way when I mindlessly tapped on the screen and thought I saw it flicker. Yes! I had pressed the Wipe button and it had taken me to that section. It's been working fine ever since.
I'm not claiming I did anything and I don't have a how-to on how to fix it, but it couldn't hurt to just leave the thing running in recovery for a while and see if the touchscreen comes back to life for you too.
Still, I'd love to see someone with more adb knowledge provide a simple tutorial on how to get it back to stock without access to recovery. I'm sure it would be helpful to someone in the future... maybe even me if the same problem comes up again.
Best of luck to you.

Just ignore my comment
Sent from my Amazon Kindle Fire using Tapatalk

If your on the rooted stock rom you could always wait until Amazon pushing the next OTA

You will have to make a fastboot image and flash that with fastboot. But before you create the image, you will have to create all the appropriate symlinks. Then you run...
Code:
make_ext4fs -l 512m -a system -s /path/to/fastboot_system.img /path/to/system_folder
That will create the fastboot image. Then when FFF gives you fastboot access, you run...
Code:
fastboot flash system fastboot_system.img
You will also need a fastboot image for recovery and the bootloader.

Isn't there any easy way like with my desire, simple ruu.
Or hasn't anyone created these images to flash. I also need to get back to stock everything and send it to amazon, my wifi gets error after some period of time and some times when screen goes off, try'd 3 roms and stock.

There is a way to tell the device to install /sdcard/update.zip via shell commands. I forget what they are tho. Something about the extendedcommands. If I have time tomorrow I'll look it up.

here it is:
http://www.theandroidsoul.com/kindle-fire-stock-rom-installation-guide/

b63 said:
here it is:
http://www.theandroidsoul.com/kindle-fire-stock-rom-installation-guide/
Click to expand...
Click to collapse
Thanks for the link. I'm back on this thread because I think my Kindle Fire touchscreen is now dead for good. However, those instructions do not work as-is because you need to press a button on the screen to tell the Kindle Fire to allow the host to mount it as a USB Mass Storage device. Although those instructions don't get you all the way there, I was able to use the core idea to get my Kindle Fire back to stock. So, many thanks for pointing me in the right direction.
On top of the touchscreen not working, I ended up partially bricking the device trying to find a way to flash it back to stock, so I had also posted in the Unbricking thread. I posted my solution there....
http://forum.xda-developers.com/showpost.php?p=23226260&postcount=701
Odds are, if you have a device that is booting correctly, you will be able to ignore steps 3 and 4 and get it booting back to stock. I do have a couple of other suggestions... Leave your USB cable hooked up to the Kindle Fire as it boots into stock for the first time. This is the only time that it will automatically mount the /sdcard to your computer and you will have a chance to reclaim (and delete) all the files stored there. You can also do something like 'adb pull /sdcard C:\sdcard' before you flash. Also, depending on what ROM and apps you were using before starting the process, you might want to delete your user data and reset the device to factory defaults. You can do this with 'fastboot erase userdata' and the next time you start the device, you'll get a warning that it's about to reset. Hit the power button and you should have a clean, fresh from the factory Kindle fire... albeit with a broken touchscreen. Good luck!

After several failed attempts to follow this guide (no offense to posters; I appreciate your contributions), I found this to be the simplest method.
http://stackoverflow.com/questions/10817721/wipe-data-factory-reset-through-adb
Download stock update, then it's basic procedure in adb:
adb push C:/update.zip /sdcard/update.zip
adb shell
recovery --wipe_data
After reboot, go back into to adb shell and do "recovery--update_package=/sdcard/update.zip"
Factory reset, etc. and you're good to go.

[Q] Fastboot Reason: Sticky bit factory_fastboot?

I flashed the Eclipse ROM via safestrap and then restored the Eclipse ROM onto the stock ROM slot. For some stupid reason, instead of restoring the stock ROM slot before resetting the phone back to stock, I opted to use RSD Lite 6.1.4 and tried to flash the JB firmware (yes, I got into fastboot). When I tried to do this, the phone reboots past the Motorola M insignia, to the droid startup screen (with the flashing red light/circle), but does not get past the startup screen (yes, I gave it 30+ minutes to no avail). I also tried to reflash the JB firmware, but no matter what, I ended up stuck at the bootup screen.
For this reason, I tried to flash the ICS firmware instead (per instructions on XDA and other websites, I removed the lines in the XML file that had the word var, getvar, and oem). This did work! However, after RSD flashed the firmware, rather than restarting into the OS, the phone reboots into a black screen w/ the phrase "Fastboot Reason: Sticky bit factory_fastboot" at the very bottom. Anytime I try to restart the phone, it automatically boots into this screen. If I hold the volume up and down buttons, together w/ the power button, I am able to get back to the option to start normally.
When I tried to do the OTA JB update, the phone downloads the necessary files, but when the phone tries to reboot to install the OS update, it goes back into that black screen and does not install the update. Also, when I finally do get back into the OS, the phone then constantly reboots as if it were trying to install the OTA JB update.
Does anyone know what "Fastboot Reason: Sticky bit factory_fastboot" means? Also, if anyone knows how to "fix" this issue, I'd greatly appreciate it. If the fix requires command line work (like in this thread), I'd greatly appreciate if someone could walk me through it step-by-step, as I am not familiar w/ the command line process.
Thanks!
Edit 1: The next step I will try is to get root back on my phone, install Safestrap, and see whether I can flash a backup that I previously had.
Edit 2: In some threads for other Moto phones, there is some discussion regarding using ADB to fastboot/flash the stock ROM. Anyone know how this is different from using RSD? Also, can anyone walk me through HOW to ADB? I have zero knowledge in this regard.

Have you tried holding the buttons down to enter fast boot again and reflash? Worth a shot if you haven't. You could also attempt a factory reset from the boot menu. Maybe the corrupt file would correct itself.
You should definitely take the time to learn some ADB; at least a working understanding. It helps down the road.
Here's a good tutorial on ADB commands. http://mobile.tutsplus.com/tutorials/android/android-adb-quick-guide/
And to install ADB without Android SDK (app production software) http://mobilecon.info/install-adb-in-windows.html
Sent from my Nexus 7 using xda app-developers app

skippid said:
Have you tried holding the buttons down to enter fast boot again and reflash? Worth a shot if you haven't. You could also attempt a factory reset from the boot menu. Maybe the corrupt file would correct itself.
You should definitely take the time to learn some ADB; at least a working understanding. It helps down the road.
Here's a good tutorial on ADB commands. http://mobile.tutsplus.com/tutorials/android/android-adb-quick-guide/
And to install ADB without Android SDK (app production software) http://mobilecon.info/install-adb-in-windows.html
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Yes, I attempted to reflash on multiple occasions, both using the stock ICS and the stock JB roms. I must have reflashed close to 10x at this point. In any case, no matter how often I have reflahsed (including after doing a factory reset from within the OS as well as from within recovery), I still get the error. The good news is that I was successfully able to flash the JB ROM and have the phone OS actually start up, whereas, a few days ago, it would be stuck at the red circle/eye thing.
Furthermore, I attempted the command fastboot flash system [system.img], and I got the error:
(bootloader) Variable not supported!
target reported max download size of 31457280 bytes
error: cannot load '[system.img]': no error
I saved the system.img in both c:\android, as well as the internal SD card of the phone.
The other good news is that I am still able to use the phone if I get into the boot menu and ask the phone to boot normally. However, I am now unable to get root, and anytime I need to restart the phone, it gives me that error message.
I have also tried the command fastboot reboot bootloader but continue to get the same error message.

OK. Find a JB leak zip or current stock JB zip, access the screen where it asks for AP Fast boot and recovery, choose recovery, then volume up I believe when the phone shows the android with the red exclamation point.. Then choose update with zip. Search your SD card and install. It's worth a try in this manner in case you haven't already.
That's odd that your phone didn't respond well with RSD.
Sent from my XT907 using xda app-developers app

You need to use an updated fastboot binary for the new larger images in these devices.
http://db.tt/AveMC40y

skippid said:
OK. Find a JB leak zip or current stock JB zip, access the screen where it asks for AP Fast boot and recovery, choose recovery, then volume up I believe when the phone shows the android with the red exclamation point.. Then choose update with zip. Search your SD card and install. It's worth a try in this manner in case you haven't already.
That's odd that your phone didn't respond well with RSD.
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
Skippid, thanks for the suggestions. I tried your method as well. Went into recovery, selected to update from external SD (or something to that effect), selected the JB zip file, and let it flash that way. Unfortunately, I still received the same error message regarding the sticky bit factory_fastboot.

cellzealot said:
You need to use an updated fastboot binary for the new larger images in these devices.
http://db.tt/AveMC40y
Click to expand...
Click to collapse
cellzealot, thank you for the link. I've downloaded the file that you linked to. Could you be so kind as to now give me a step-by-step on how to re-attempt the flashing process?

Quick update - I was able to get root back, installed safestrap, and flashed the nandroid that I had made back when I first flashed Eclipse. However, I am still having the same issue:
Whenever I restart the phone, I get the sticky bit factory_fastboot error. If I use the command fastboot continue, the phone boots up as normal; however, it would be great to not have to do this each and every time I reboot the phone. Any help would be greatly appreciated. Thanks!

More updates (still not fixed):
After getting root, I reflashed my nandroid, factory reset (both within the OS and in recovery), and then tried flashing both the ICS and JB stock ROMs. I tried flashing both using mfastboot, as well RSD Lite. The files flash successfully; however, whenever I restart the phone, I continue to get the stick bit factory_fastboot error.
Also, when I get into recovery, I try to flash via "update from external SD". When I do so, recovery simply restarts without flashing the stock ROM.

Here's my last update as to this issue:
After trying all of the methods that I could think of (RSD Lite, flashing via fastboot and mfastboot, flashing from external), the problem did not correct itself.
I brought my phone into a Verizon store, where they told me that they had never seen that problem before. They agreed to replace my phone pursuant to the one-year warranty (I received my phone in December), which I received today. I've again rooted my phone, but have opted to not screw around w/ safestrap and custom ROMs this time around, as I find the stock JB experience to actually be quite good.

Found the soultion!!!!!!
Ok guys so after serching a while I found out similar moto phones have the same issue. I found in a latin forum and in a Droid forum people ponting to the same issue. So the solution that worked for my Razr HD xt925 was:
1) Enter fastboot mode in your phone (very easy since every time you restart the phone you end there anyways)
2) Write this command on the computer: fastboot oem fb_mode_clear
there will be a dialogue with the time take and OK
You are done!
Thought someone might find it useful

Thank you!
cerafio said:
Ok guys so after serching a while I found out similar moto phones have the same issue. I found in a latin forum and in a Droid forum people ponting to the same issue. So the solution that worked for my Razr HD xt925 was:
1) Enter fastboot mode in your phone (very easy since every time you restart the phone you end there anyways)
2) Write this command on the computer: fastboot oem fb_mode_clear
there will be a dialogue with the time take and OK
You are done!
Thought someone might find it useful
Click to expand...
Click to collapse
Thank you! This was the answer I needed after searching and searching trying all the different things for over 3 hours, this 2 second fix worked!

Namanati said:
Thank you! This was the answer I needed after searching and searching trying all the different things for over 3 hours, this 2 second fix worked!
Click to expand...
Click to collapse
#8 > http://forum.xda-developers.com/droid-razr-m/general/guide-faq-how-to-root-boot-unlock-t2869432

ATTACK said:
#8 > http://forum.xda-developers.com/droid-razr-m/general/guide-faq-how-to-root-boot-unlock-t2869432
Click to expand...
Click to collapse
Thanks, but that didn't come up when I googled AP Fastboot: flash failed, and since I didn't get it from rooting or unlocking my phone I didn't think to look for that.

cerafio said:
Ok guys so after serching a while I found out similar moto phones have the same issue. I found in a latin forum and in a Droid forum people ponting to the same issue. So the solution that worked for my Razr HD xt925 was:
1) Enter fastboot mode in your phone (very easy since every time you restart the phone you end there anyways)
2) Write this command on the computer: fastboot oem fb_mode_clear
there will be a dialogue with the time take and OK
You are done!
Thought someone might find it useful
Click to expand...
Click to collapse
Oh my god dude thank you so much. That fixed my bootloader issue that was plaguing me for weeks
Thanks again!!!

cerafio said:
Ok guys so after serching a while I found out similar moto phones have the same issue. I found in a latin forum and in a Droid forum people ponting to the same issue. So the solution that worked for my Razr HD xt925 was:
1) Enter fastboot mode in your phone (very easy since every time you restart the phone you end there anyways)
2) Write this command on the computer: fastboot oem fb_mode_clear
there will be a dialogue with the time take and OK
You are done!
Thought someone might find it useful
Click to expand...
Click to collapse
Thanks Man You really saved my razr.:good:

Edit : Sorry I asked stupid question!

Pierro29 said:
Edit : Sorry I asked stupid question!
Click to expand...
Click to collapse
there are no stupid questions if you question its because you dont know something and would like to fulfill the empty space where a reasonable answer could go. and s thanks for the solution to this error.

Okay, I have a "stupid"/newbie question. I flashed an image and I am getting the sticky boot thing. How to a get to a window to type the lines in?
Thanks!

cerafio said:
Ok guys so after serching a while I found out similar moto phones have the same issue. I found in a latin forum and in a Droid forum people ponting to the same issue. So the solution that worked for my Razr HD xt925 was:
1) Enter fastboot mode in your phone (very easy since every time you restart the phone you end there anyways)
2) Write this command on the computer: fastboot oem fb_mode_clear
there will be a dialogue with the time take and OK
You are done!
Thought someone might find it useful
Click to expand...
Click to collapse
Hey dude ! You save my life
Awesome trick

[Q] After 4 1/2 yrs on XDA I am finally stuck! Bricked No download mode, No OS.

Hello my fellow XDA Members. I am stuck in a tight spot and after reading and re-reading some things the situation doesn't look very promising. I hope this is the moment that Karma shows up and I can get some help on this. Here it goes.
Specs - LG G2 D801 Variant > TWRP V2.8.3.1 > NO OS Currently
I was running Cloudy G3 Rom smoothly and got bored and decided to flash that new rom that is a 5.0 Rom all variants. Did the usual back ups and flashed it. Something happened when I flashed the rom. It went through the Aroma installer and then said "successful" but stuck in a bootloop. I tried it again and nothing happened. Then I tried to wipe everything again and started getting an E: Cannot mount (data or system I forget which as that error went away after I completely formatted data, wiped everything and reflashed Cloudy Stock. )
> Cloudy stock bootlooped and nothing is happening in TWRP. I Am using the USB OTG method of getting files on the phone and getting it charged but anytime I try to do anything (flash a rom, an older version of TWRP) it just immediately restarts TWRP and thats that. I have No OS at all.
> I tried to use one of the methods to get into download mode and flash a stock KDZ but the phone acts like it is going into DL mode (shows the little blue transition screen) but never gets into the ACTUAL download mode where the PC or flash tool can recognize it.
So in a nutshell > No OS > I can get into TWRP but it does nothing > No Download Mode > Don't want a new phone > Don't want to take it apart and try to short circuit anything if possible. LOL.
I am totally stuck here. I am done alot of work and even helped friends and family out with their devices over the years. I am just not sure if I need to consider it a done deal and get a new phone or maybe one of you guys know of something easy and obvious (please let it be the latter) I am missing. Thanks for any help you can offer. I Will be standing by.

Have you tried to reflash bootloader? If not, do that and reflash cloudy right away

wisefreakz said:
Have you tried to reflash bootloader? If not, do that and reflash cloudy right away
Click to expand...
Click to collapse
I haven't thought about flashing a bootloader. How would I flash the bootloader if I can not the phone into either DL mode and or TWRP doesn't do anything either? Is a bootloader file just a flashable file like any other .zip file?

jcnbama said:
I haven't thought about flashing a bootloader. How would I flash the bootloader if I can not the phone into either DL mode and or TWRP doesn't do anything either? Is a bootloader file just a flashable file like any other .zip file?
Click to expand...
Click to collapse
@jcnbama
Have you tried this or this?

euphoria360 said:
@jcnbama
Have you tried this or this?
Click to expand...
Click to collapse
The first one I can not do as I do not have any knowledge at all of Ubuntu, Linux, or any of that. It would take forever to get a working knowledge of that software in order to get things going again. I would probably just have to either take it to a cellphone repair shop or get another phone before I could do the first link.
I have not tried the second one but it is a viable option. I was looking at it online and trying to talk myself down from having to do that. I would reallllllllly rather not have to take my phone apart if I can keep from so that's kind of what this post is all about. Just trying to see if anyone knows of ANYTHING else before I go taking apart my phone.

Can you describe more about "twrp doesnt do anything"?
Does twrp boot up?
Can u see/wipe partitions?
Can u install any rom in twrp? Does it finish?

euphoria360 said:
Can you describe more about "twrp doesnt do anything"?
Does twrp boot up?
Can u see/wipe partitions?
Can u install any rom in twrp? Does it finish?
Click to expand...
Click to collapse
TWRP boots and I can go into wipe, advanced wipe, and format data and it says it's successful. I can use file manager and move items back and forth from USB OTG. If I try to flash anything it just reboots TWRP immediately so I can't install any .zip files at all.

My guess is that your bootloader is damaged.
The only option i can see for you is that Ubuntu thing i shared with you. So, lets stop acting lazy and do what needs to be done. Dont scare since there is nothing to loose. LG G2 is unbrikable
Booting up ubuntu or any other linux os is so easy. And there is nothing much to learn. Trust me.
Go to ubuntu website and download their newest iso file. Burn it on dvd and boot it up. You dont have to install it, just choose "live mode" and it boots up. Just like that. Then yiu can proceed with tutorial mentioned above and it shouldnt take more than an hour from you. Its all typing some commands in terminal (remember CMD in windows!).
Just make sure to download the files mentioned in that tutorial before proceeding.

euphoria360 said:
My guess is that your bootloader is damaged.
The only option i can see for you is that Ubuntu thing i shared with you. So, lets stop acting lazy and do what needs to be done. Dont scare since there is nothing to loose. LG G2 is unbrikable
Booting up ubuntu or any other linux os is so easy. And there is nothing much to learn. Trust me.
Go to ubuntu website and download their newest iso file. Burn it on dvd and boot it up. You dont have to install it, just choose "live mode" and it boots up. Just like that. Then yiu can proceed with tutorial mentioned above and it shouldnt take more than an hour from you. Its all typing some commands in terminal (remember CMD in windows!).
Just make sure to download the files mentioned in that tutorial before proceeding.
Click to expand...
Click to collapse
First of all calling people lazy is not nice. I'm not lazy I am trying to play it safe. I wouldn't want to brick it to the point to where I don't even have recovery and it can not even be charged any longer. I have Ubuntu on my desktop upstairs. I have used it a little. It's not that I am completely ignorant to Ubuntu I am just a total novice. Also the issue described in that post doesn't exactly match my situation. I am not in a black screen. It's more like a bootloop that I can not get out of because TWRP is not doing what it needs to do and I can not flash TWRP a ROM or get into DL mode at all. Also that post says,
"VERY IMPORTANT!!!!!!! You must use the img files that correspond to the ROM you have installed before getting the problem to avoid breaking your phone."
I don't have a rom on my phone soooo...

You didn't answer my question well. If on TWRP you can finish installing rom without any error, and you keep coming to twrp after restarts, that's another situation. Try this:
http://forum.xda-developers.com/showthread.php?t=2451696
But if you cant even finish install in twrp (twrp gives you errors or just restarts before giving you "successful", either you have problem in rom you try to flash or you need to build everything up from start.
That lazy thing was for encouraging you to do it.
And you cant brick your device. There is always a way on G2.
For img files: find them from last stock rom that was working on your phone.

Deleted