[GUIDE][nvFlash]The Chickens Guide to Flashing the bootloader manually - Acer Iconia A500

here is a guide and some pix so you can see what 'should' happen when using civato's nvFlash manual method.
Get yr 15 digit CPUID - not your 11/13 digit ICS serial no.
the correct uid is VITAL, using the wrong one can cause you problems.
all righty you've made the decision to flash the patched bootloader and install a custom recovery and one of the many custom ICS/JB roms -
1. Ensure both Acer and adb drivers are installed
2. Retrieve HC CPUID
3. Generate your SBK from Blackthund3rs site: http://a500bootloaderflash.tk/sbkcalc/
4. Download yr ROM of choice and put it on yr external sd card
5. Put your tab in APX Mode manually or with apxFlashTool
6. Flash the Bootloader/Custom Recovery
7. Reboot to Custom recovery and do a full data wipe/format
8. Flash your chosen ICS/JB ROM
9. For good measure reboot to recovery and do another full wipe
10. Reboot and enjoy ICS/Jellybean
nb: I know it sounds overkill for all these data wipes/formats but in my experiences and alot of others on here multiple wipes ensure a smooth
running rom
Prep Work
To enter APX mode - Turn your tab off then press and hold in the Reset button(with paper clip).
Do not release it.
Press and hold power for 3 secs and then release it.
After another second, release the reset button.
Download V8-UNL-ICS-HC-bootloader-MULTI-cwm and extract the files for the manual nvFlash
If you are coming from HC then d/l your ICS/JB rom of choice to yr ext sdcard
WARNING: at Step 7. Do not "press any key to continue..." UNLESS yr tab is in bootloader mode, doing so causes alot more issues and
necessitates a rollback to HC if you continue....
*****************************************************
ok here we go:
Step 1. You must enter APXMode FIRST
Your Windows PC should then detect your device and install the APX driver. You should then have an APX USB device installed.
If you do not have an APX USB device listed in your system tray, you cannot proceed.
The screen of your tablet is black and the Power Light is ON
Step 2. Once yr tabs screen has turned black and the power lite is on then
Step 3. Right click on the v8.bat file from civs package and choose "Edit"
Go thru the file and remove any "Cls" lines if there are any - this allows you to see what the flash is doing.
Save the changes thenRun the bat file - i'm using V6-3.bat in this example but if you are using v8 it will be named v8.bat
NOTE: You will see an instruction on the opening screen to "delete recovery from boot.p file"
On a reboot, this file overwrites your newly flashed custom recovery with the Acer Stock Recovery, not what we want!!
Please check /system for the boot.p file - if its there then delete or rename it b4 going on
Step 4. Enter your SBK
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 5. Your tab will display this - "System Information" Screen
Here you can see clearly your one and only cpuid!!!! Or 'chip uid' as it is named here.
Warning: If this system info is not displayed you run the risk of getting stuck in apx mode....
Close out of the command window and disconnect your USB and check yr SBK and/or the Acer USB Driver is showing in your "Safely remove hardware" icon
if it isnt reinstall the Acer Drivers
Step 6. All systems are go!! Go ahead and press any key...when your tab is in bootloader mode
7. WAIT for your tab to display "Acer Iconiaa500 APX Mode"
this is 'bootloader mode' where the flash needs to take place,
then press any key...
if you carry on without yr tab showing this message...
then you will softbrick and to fix that you will need to downgrade to HC and
you will lose all your data
There are 'usually' only 3 reasons you will not see the "Acer Iconia a500 APX Mode" message
1. The Drivers are failing to install correctly
2. Incorrect cpuid
3. Getting stuck at Formatting/partition errors is the ".bct issue" apxFlashTool 0.4 fixes this
Step 8 the flash begins!!!
the flash will take about 30 secs at most
on your tab you will see in big white letters the word PASS
in smaller red letters "Reboot the Device"
So power down yr tab and reboot into your new recovery and backup your system then flash your ICS/Jellybean Rom.
Congratulations you are no longer a chicken
EDIT: I've tried not to put too much info in here to keep things relatively easy to read - if you think there is info that should be in here just let me know and I'll add it

:good::good:
Nice guide. Should help out anyone who is still unsure. The only thing is, where's Daisy?

JdgM3NT4L said:
:good::good:
...The only thing is, where's Daisy?
Click to expand...
Click to collapse
hahaha, funnee J:laugh::laugh::laugh: good ol' Daisy
and for those wondering what else you can do with your unlocked bootloader...
you too can enjoy the 'Daisy' boot logo hehehe!!

dibb_nz said:
hahaha, funnee J:laugh::laugh::laugh: good ol' Daisy
and for those wondering what else you can do with your unlocked bootloader...
you too can enjoy the 'Daisy' boot logo hehehe!!
Click to expand...
Click to collapse
lmao.
this guide should be stickied eh?

can you get a bit more detailed for these?
Ensure both Acer and adb drivers are installed
2. Retrieve HC CPUID
3. Generate your SBK using the CPUID from vaches site

lbhocky19 said:
can you get a bit more detailed for these?
Ensure both Acer and adb drivers are installed
2. Retrieve HC CPUID
3. Generate your SBK using the CPUID from vaches site
Click to expand...
Click to collapse
For info on the drivers and retrieving yr cpuid see this guide here but basically you'll need the acer drivers from acer support page and the android usb/adb drivers, these drivers ensure yr tab can communicate with yr pc and can be d/l in a zip file from post in the link above.
The SBK (Secure Boot Key) is generated from the cpuid. Go to vaches site (the link is provided in the nvflash as u can see in the first pic above) Its as simple as entering yr cpuid in the box and it will give you a number formatted like this:
0x000D0000 0x00000001 0x0AAACCCC 0x0000000 - this is your SBK

chismay said:
lmao.
this guide should be stickied eh?
Click to expand...
Click to collapse
hey dude!! good to see u, pls tell me you;ve taken daisy for a spin m8????????
or r u still in that henhouse:laugh::laugh::laugh::laugh:

<Deleted by user>

Stuck on Step 8
First of all thank-you so much for writing this it has been very helpful so far.
Got stuck on Step 8, I did everything exactly as stated, go to the green Acer logo, with "Acer Iconia APX Made" at the top left, but command prompt returned with the following:
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x120002
FAILED!
command failure: format partition failed <bad command>
Bootloader status: unknown operation <code: 1> message: flags: 0
Before that in step 7 I also got an error, but the it allowed press an key to continue anyway:
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d88011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader_apx.bin
| 714980/714981 bytes sent
bootloader_apx.bit sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed <bad data>
bootloader status: partition table is invalid, missing required information <code: 14> message nverror:0x4 (0x4) flags: 0
I realize that I have probably given too much information and I apologize for that. Any help at all would be much appreciated!
Also: This was done using option 3, but I tried it with option 4 as well and got the same error. In step 5 it did not show System Information, but I checked the acer divers, the safely remove hardware and my SBK using different generators and it all checks out.
PLEASE HELP ME!!!!

Luke00123 said:
First of all thank-you so much for writing this it has been very helpful so far.
Got stuck on Step 8, I did everything exactly as stated, go to the green Acer logo, with "Acer Iconia APX Made" at the top left, but command prompt returned with the following:
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x120002
FAILED!
command failure: format partition failed <bad command>
Bootloader status: unknown operation <code: 1> message: flags: 0
Before that in step 7 I also got an error, but the it allowed press an key to continue anyway:
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d88011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader_apx.bin
| 714980/714981 bytes sent
bootloader_apx.bit sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed <bad data>
bootloader status: partition table is invalid, missing required information <code: 14> message nverror:0x4 (0x4) flags: 0
I realize that I have probably given too much information and I apologize for that. Any help at all would be much appreciated!
Also: This was done using option 3, but I tried it with option 4 as well and got the same error. In step 5 it did not show System Information, but I checked the acer divers, the safely remove hardware and my SBK using different generators and it all checks out.
PLEASE HELP ME!!!!
Click to expand...
Click to collapse
you dont say what rom you were on or whether your tab was running ok before you tried the flash??
Normally if you don't see the system info window things dont go well after that!
But in saying that it seems you've made sure everything else is right, and as long as when you put your tab in apx mode you saw the "acer download mode" displayed you should be good!!
partitioning errors such as yours are "normally" easy to fix by running timmydeans root tool - there is a link to it in the root guide in my sig.
Download it and put your tab in apx mode, connect your usb cable and then run the pbj20.exe ??
you should get asked to enter your CPUID(not the sbk!!) take off the 0x at the beginning if its there
also: in the cpuid guide (in my sig)theres a link to a short guide by "lcd047" how to use timmydeans to repartition and flash the bootloader all in one go - might wanna take a look at that while you're waiting for the download....
Originally Posted by lcd047 wrote:
"I downloaded timmyDean's root-3.2.1-V4.7z
I booted the tablet (in APX mode) and I connected the USB cable to it
in the directory root-3.2.1/Image I run the command
nvflash --bct flash.bct --setbct --odmdata 0x100c0105 --configfile flash.cfg --create --bl bootloader.bin --sbk (your sbk number after converting your UID number) 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX --go
without rebooting, I flashed the v7 bootloader and recovery as per the bootloader thread; since the partition table was restored at the previous step, the operation now succeeded;
I rebooted the tablet in recovery, and proceeded to wipe the data and flash a ROM the usual way.
Click to expand...
Click to collapse
let us know how you go
rgds dibb

Still Stuck
Right sorry. I am sunning the stock Acer ICS 4.0.3 rom, with the stock ICS 4.0.3 recovery image and ICS bootloader 3.12-ICS.
I tried running the file PBJ20upgrade.exe with my tablet pluged in in APX mode, but it told me to make sure my tablet was unpluged and that if a new hardware window opened to close it (as if it was going to install drivers or something). I did this and clicked continue but a window poped up sating EUUs had stopped. I traied it also leaving my tablet plugped in, same results.
If it is of significance I am using the Acer drivers verson: USB Driver_Acer_1.06.1500_A30H_A500. The other version: USB_Acer_1.00.0524_A30HA31HA32H_A (the one that blackthunder has you download) would not install saying that no previous version was found.

Myt have put u a bit wrong there. There's 2 ways to run it...if via .exe don't connect yr cable and wait for steps to run via apex mode.
If running lcd047 steps... Put in apx mode and run the bat file in the image folder
Is that bit clearer??
Sent from my GT-I9300 using Tapatalk 2

THANK-YOU!!!
Luke00123 said:
Right sorry. I am sunning the stock Acer ICS 4.0.3 rom, with the stock ICS 4.0.3 recovery image and ICS bootloader 3.12-ICS.
I tried running the file PBJ20upgrade.exe with my tablet pluged in in APX mode, but it told me to make sure my tablet was unpluged and that if a new hardware window opened to close it (as if it was going to install drivers or something). I did this and clicked continue but a window poped up sating EUUs had stopped. I traied it also leaving my tablet plugped in, same results.
If it is of significance I am using the Acer drivers verson: USB Driver_Acer_1.06.1500_A30H_A500. The other version: USB_Acer_1.00.0524_A30HA31HA32H_A (the one that blackthunder has you download) would not install saying that no previous version was found.
Click to expand...
Click to collapse
It work! Thank-you all SOOOOOOOO MUCH!
I missed the second half of your post! I flashed everything back to HC and then installed the new Bootloader and Reovery!

haha....you are sooooo welcome, pleased you got it, happy flashing!!!
rgds
dibb
Sent from my GT-I9300 using Tapatalk 2

Luke00123 said:
It work! Thank-you all SOOOOOOOO MUCH!
I missed the second half of your post! I flashed everything back to HC and then installed the new Bootloader and Reovery!
Click to expand...
Click to collapse
Hey can u please tell me how did it work for u ... cause i have a similar problem and i cant figure it out ..here what i get:
bootloader downloaded successfulyy
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
bootloader status: failed to create the partition <code : 10> message: nverror:0x5
<0x1000005> flags: 0
What is the problem here ?

moizsami said:
Hey can u please tell me how did it work for u ... cause i have a similar problem and i cant figure it out ..here what i get:
bootloader downloaded successfulyy
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
bootloader status: failed to create the partition <code : 10> message: nverror:0x5
<0x1000005> flags: 0
What is the problem here ?
Click to expand...
Click to collapse
Hardware fault probably, especially so if none of the re-partitioning tools work i.e tdv4/babsector and you're positive you're following instructions correctly

moizsami said:
Hey can u please tell me how did it work for u ... cause i have a similar problem and i cant figure it out ..here what i get:
Click to expand...
Click to collapse
Sure I followed these instructions:
"I downloaded timmyDean's root-3.2.1-V4.7z
I booted the tablet (in APX mode) and I connected the USB cable to it
in the directory root-3.2.1/Image I run the command
nvflash --bct flash.bct --setbct --odmdata 0x100c0105 --configfile flash.cfg --create --bl bootloader.bin --sbk (your sbk number after converting your UID number) 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX --go
without rebooting, I flashed the v7 bootloader and recovery as per the bootloader thread; since the partition table was restored at the previous step, the operation now succeeded;
I rebooted the tablet in recovery, and proceeded to wipe the data and flash a ROM the usual way.
Click to expand...
Click to collapse
This will reset your tablet to the HC ROM, HC bootloader and (I believe) Flash a custom recovery. If you are wanting to flash 4.2 or 4.1 though, you are going to want your ICS boot loader back, so just follow the instructions in this post to get an unlocker version and it should work. Also I was having trouble getting my CPUID after I reset my tablet back to HC, but I went ahead and tried the method in the post using the same SKB and it worked.
Good luck

Thanks for the tips man, its awesome

Great guide, worked perfectly to install this rom http://forum.xda-developers.com/showthread.php?t=2239476 :good:
Thanks

dibb_nz said:
here is a guide and some pix so you can see what 'should' happen when using civato's nvFlash manual method.
Get yr 15 digit CPUID - not your 11/13 digit ICS serial no.
the correct uid is VITAL, using the wrong one can cause you problems.
all righty you've made the decision to flash the patched bootloader and install a custom recovery and one of the many custom ICS/JB roms -
1. Ensure both Acer and adb drivers are installed
2. Retrieve HC CPUID
3. Generate your SBK from Blackthund3rs site: http://a500bootloaderflash.tk/sbkcalc/
4. Download yr ROM of choice and put it on yr external sd card
5. Put your tab in APX Mode manually or with apxFlashTool
6. Flash the Bootloader/Custom Recovery
7. Reboot to Custom recovery and do a full data wipe/format
8. Flash your chosen ICS/JB ROM
9. For good measure reboot to recovery and do another full wipe
10. Reboot and enjoy ICS/Jellybean
nb: I know it sounds overkill for all these data wipes/formats but in my experiences and alot of others on here multiple wipes ensure a smooth
running rom
Prep Work
To enter APX mode - Turn your tab off then press and hold in the Reset button(with paper clip).
Do not release it.
Press and hold power for 3 secs and then release it.
After another second, release the reset button.
Download V8-UNL-ICS-HC-bootloader-MULTI-cwm and extract the files for the manual nvFlash
If you are coming from HC then d/l your ICS/JB rom of choice to yr ext sdcard
WARNING: at Step 7. Do not "press any key to continue..." UNLESS yr tab is in bootloader mode, doing so causes alot more issues and
necessitates a rollback to HC if you continue....
*****************************************************
ok here we go:
Step 1. You must enter APXMode FIRST
Your Windows PC should then detect your device and install the APX driver. You should then have an APX USB device installed.
If you do not have an APX USB device listed in your system tray, you cannot proceed.
The screen of your tablet is black and the Power Light is ON
Step 2. Once yr tabs screen has turned black and the power lite is on then
Step 3. Right click on the v8.bat file from civs package and choose "Edit"
Go thru the file and remove any "Cls" lines if there are any - this allows you to see what the flash is doing.
Save the changes thenRun the bat file - i'm using V6-3.bat in this example but if you are using v8 it will be named v8.bat
NOTE: You will see an instruction on the opening screen to "delete recovery from boot.p file"
On a reboot, this file overwrites your newly flashed custom recovery with the Acer Stock Recovery, not what we want!!
Please check /system for the boot.p file - if its there then delete or rename it b4 going on
Step 4. Enter your SBK
Step 5. Your tab will display this - "System Information" Screen
Here you can see clearly your one and only cpuid!!!! Or 'chip uid' as it is named here.
Warning: If this system info is not displayed you run the risk of getting stuck in apx mode....
Close out of the command window and disconnect your USB and check yr SBK and/or the Acer USB Driver is showing in your "Safely remove hardware" icon
if it isnt reinstall the Acer Drivers
Step 6. All systems are go!! Go ahead and press any key...when your tab is in bootloader mode
7. WAIT for your tab to display "Acer Iconiaa500 APX Mode"
this is 'bootloader mode' where the flash needs to take place,
then press any key...
if you carry on without yr tab showing this message...
then you will softbrick and to fix that you will need to downgrade to HC and
you will lose all your data
There are 'usually' only 3 reasons you will not see the "Acer Iconia a500 APX Mode" message
1. The Drivers are failing to install correctly
2. Incorrect cpuid
3. Getting stuck at Formatting/partition errors is the ".bct issue" apxFlashTool 0.4 fixes this
Step 8 the flash begins!!!
the flash will take about 30 secs at most
on your tab you will see in big white letters the word PASS
in smaller red letters "Reboot the Device"
So power down yr tab and reboot into your new recovery and backup your system then flash your ICS/Jellybean Rom.
Congratulations you are no longer a chicken
EDIT: I've tried not to put too much info in here to keep things relatively easy to read - if you think there is info that should be in here just let me know and I'll add it
Click to expand...
Click to collapse
Is there any cure for being "stuck in APX mode"?

Related

Solution: Unlocked bootloader Installation

One of my counterparts in Germany asked me to post it here. All credit goes to opec. This has been covered a few times, but I like the detailed scenario.
**************************
ERROR: Can´t installl hacked ICS Bootloader
I tried installing Hacked ICS Bootloader in Order to get Moscow Desire´s "Alexandra V a501 ICS 4.0.3 ver 1.4 Final" running on my a501.
The following ways of flashing could get the hacked bootloader on my a501:
"Afterota for A600/G100W" (http://forum.xda-developers.com/show....php?t=1675939),
"blackthund3r´s ATX flash tool A500APXFlash.exe" (see "Automated flashing tools" at http://forum.xda-developers.com/showthread.php?t=1622425")
"Manual flashing via nvflash" (see Manual flashing at http://forum.xda-developers.com/show....php?t=1622425)
Trying to flash with this tools always brought me to a Command Promt saying:
Nvflash started
[resume mode]
APX flash tool hang when it tired to Format Partition 4 etc.
and then doing nothing even if i let it stay for hours. No Information or Error so long.
When i tried flashing manualy (see link above)i finaly saw an error:
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: partition table is invalid, missing required information
e: 14) message: nverror:0x4 (0x4) flags: 0
So it seemed however that the partition table on my a501 got messed up. Asking google for "failed executing command 25 NvError 0x120002" brought me to an answer "lcd047" posted on tegraowners (http://forum.tegraowners.com/viewtop...p=15285#p15331)
He desicrbes same problem with messed up partition table an restoring it with timmyDean´s root-3.2.1-V4.7z (http://forum.xda-developers.com/show...&postcount=1):
lcd047 wrote:
"I downloaded timmyDean's root-3.2.1-V4.7z
I booted the tablet (in APX mode) and I connected the USB cable to it
in the directory root-3.2.1/Image I run the command
nvflash --bct flash.bct --setbct --odmdata 0x100c0105 --configfile flash.cfg --create --bl bootloader.bin --sbk (your sbk number after converting your UID number) 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX --go
without rebooting, I flashed the v7 bootloader and recovery as per the bootloader thread; since the partition table was restored at the previous step, the operation now succeeded;
I rebooted the tablet in recovery, and proceeded to wipe the data and flash a ROM the usual way.
And that worked for me. After flashing, my a501 did a automated reboot, i quickly killed the reboot by holding the Power Button (guessing killing the reboot is not realy necessary because the booting shouldn´t mess up the partition table again) and then brought the devive back to APX Mode (Holding Reset and Power for 3-4 sec. then releasing Power and after 1 second relesaing Reset).
Then i flashed the hacked bootloader via blackthund3rs APX flash tool (see link above).
Then i installed Alexandra V as Moscow Desire descirbes (see "To Install" at http://forum.xda-developers.com/show....php?t=1635577)
It took my 2 days of trial and error, but finaly give me a nice working Alexandra ROM on my a501!
Hope this helps people having the same issues.
Thanks to Moscow Desire, civato, blackthund3r, gersma, zeroNull, lcdß47, timmyDean
***************************************
Note from MD. You guys take note of this. Sometimes, when you get corrupted partition tables, you may have to go back to an HC stock bootloader to get them fixed. Of course there are other methods, but require some indepth knowledge, and this method most people can do easily.
MD
Borked Partition Table
Nice M...thanks for reposting this
will this work on a500
Moscow Desire said:
One of my counterparts in Germany asked me to post it here. All credit goes to opec. This has been covered a few times, but I like the detailed scenario.
Click to expand...
Click to collapse
After hours and hours, this right here was the solution I needed. Many, many thanks.
erndixon said:
After hours and hours, this right here was the solution I needed. Many, many thanks.
Click to expand...
Click to collapse
No problem. Sometimes things get buried back in the threads after awhile.
MD
Help
i'm use a501 3.2.1 stock HC and still unroot.
Now i wanna use alexV ROM, so i have flash ICS BL use blackthunder's flash tools and it's success, with V8a50pub recovery.
but my problem is:
1. still able to boot my stock HC ROM,
2. can't boot into recovery mode, it will display green robot with exclamation in its body
3. can i get guide to flash cwm recovery? i want use CWM-install-A500PubRecovery_v0.2.zip but its extension is .img and i dont know how to use it
sory if i asked noob question
thanks
Go on youtube and just search up how to root acer a500 , its the first video, steps are simple but i'm not too sure you can use pub recovery on honeycomb, after that use one of the flashing tools to install the hacked bootloader ( i prefer the apx flashtool, its fool proof pretty much with the sbk generator built in ) and download the v8 bootloader with your recovery choice and install it, there's even a guide on youtube on how to do it, hope it helps
Sent from my Iconia A501 using xda app-developers app
gigacats said:
i'm use a501 3.2.1 stock HC and still unroot.
Now i wanna use alexV ROM, so i have flash ICS BL use blackthunder's flash tools and it's success, with V8a50pub recovery.
but my problem is:
1. still able to boot my stock HC ROM,
2. can't boot into recovery mode, it will display green robot with exclamation in its body
3. can i get guide to flash cwm recovery? i want use CWM-install-A500PubRecovery_v0.2.zip but its extension is .img and i dont know how to use it
sory if i asked noob question
thanks
Click to expand...
Click to collapse
Please do not post duplicate issues in multiple threads. Please go to your original post.
MD
OK, sorry guys
Sent from my A501 using xda app-developers app
gigacats said:
OK, sorry guys
Sent from my A501 using xda app-developers app
Click to expand...
Click to collapse
No problem
Glad you got things running good. (in the other thread)
MD
Moscow Desire said:
One of my counterparts in Germany asked me to post it here. All credit goes to opec. This has been covered a few times, but I like the detailed scenario.
**************************
ERROR: Can´t installl hacked ICS Bootloader
I tried installing Hacked ICS Bootloader in Order to get Moscow Desire´s "Alexandra V a501 ICS 4.0.3 ver 1.4 Final" running on my a501.
The following ways of flashing could get the hacked bootloader on my a501:
"Afterota for A600/G100W" (http://forum.xda-developers.com/show....php?t=1675939),
"blackthund3r´s ATX flash tool A500APXFlash.exe" (see "Automated flashing tools" at http://forum.xda-developers.com/showthread.php?t=1622425")
"Manual flashing via nvflash" (see Manual flashing at http://forum.xda-developers.com/show....php?t=1622425)
Trying to flash with this tools always brought me to a Command Promt saying:
Nvflash started
[resume mode]
APX flash tool hang when it tired to Format Partition 4 etc.
and then doing nothing even if i let it stay for hours. No Information or Error so long.
When i tried flashing manualy (see link above)i finaly saw an error:
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: partition table is invalid, missing required information
e: 14) message: nverror:0x4 (0x4) flags: 0
So it seemed however that the partition table on my a501 got messed up. Asking google for "failed executing command 25 NvError 0x120002" brought me to an answer "lcd047" posted on tegraowners (http://forum.tegraowners.com/viewtop...p=15285#p15331)
He desicrbes same problem with messed up partition table an restoring it with timmyDean´s root-3.2.1-V4.7z (http://forum.xda-developers.com/show...&postcount=1):
lcd047 wrote:
"I downloaded timmyDean's root-3.2.1-V4.7z
I booted the tablet (in APX mode) and I connected the USB cable to it
in the directory root-3.2.1/Image I run the command
nvflash --bct flash.bct --setbct --odmdata 0x100c0105 --configfile flash.cfg --create --bl bootloader.bin --sbk (your sbk number after converting your UID number) 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX --go
without rebooting, I flashed the v7 bootloader and recovery as per the bootloader thread; since the partition table was restored at the previous step, the operation now succeeded;
I rebooted the tablet in recovery, and proceeded to wipe the data and flash a ROM the usual way.
And that worked for me. After flashing, my a501 did a automated reboot, i quickly killed the reboot by holding the Power Button (guessing killing the reboot is not realy necessary because the booting shouldn´t mess up the partition table again) and then brought the devive back to APX Mode (Holding Reset and Power for 3-4 sec. then releasing Power and after 1 second relesaing Reset).
Then i flashed the hacked bootloader via blackthund3rs APX flash tool (see link above).
Then i installed Alexandra V as Moscow Desire descirbes (see "To Install" at http://forum.xda-developers.com/show....php?t=1635577)
It took my 2 days of trial and error, but finaly give me a nice working Alexandra ROM on my a501!
Hope this helps people having the same issues.
Thanks to Moscow Desire, civato, blackthund3r, gersma, zeroNull, lcdß47, timmyDean
***************************************
Note from MD. You guys take note of this. Sometimes, when you get corrupted partition tables, you may have to go back to an HC stock bootloader to get them fixed. Of course there are other methods, but require some indepth knowledge, and this method most people can do easily.
MD
Click to expand...
Click to collapse
So, While this did not actually work in my case, it led me to do a search on "TegraOwners" for "Partition Table damaged" where I found "BadSector" which totally fixed my problem. So, A Hearty thanks to you Moscow Desire, as well as to BlackThund3r, for without his direction, I never would found your post either.
That being said, a big thanks to all the Dev's on this site, for without their hard work, there would be no reason for any of the fine information available on this site!
Hey i have a similar problem and i cant figure it out ..heres what i get:
bootloader downloaded successfulyy
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
bootloader status: failed to create the partition <code : 10> message: nverror:0x5
<0x1000005> flags: 0
What is the problem here ?
timmydeans toolkit doesnt work for me,bad sector also doesnt work, But i can see my device in safe and remove hardware...
moizsami said:
Hey i have a similar problem and i cant figure it out ..heres what i get:
bootloader downloaded successfulyy
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
bootloader status: failed to create the partition <code : 10> message: nverror:0x5
<0x1000005> flags: 0
What is the problem here ?
timmydeans toolkit doesnt work for me,bad sector also doesnt work, But i can see my device in safe and remove hardware...
Click to expand...
Click to collapse
If these 2 tools "don't work" there are only 2 possibilities
a) you're not doing things correctly
b) your tab has a faulty memory chip and needs a replacement motherboard
Acer a500 stock on acer logo-dead andriod red triangle
Moscow Desire said:
No problem. Sometimes things get buried back in the threads after awhile.
MD
Click to expand...
Click to collapse
Hello Sir
I have seen lots of post from you regarding Hacer a500 tab, I am not a geek nor a tech, but I do have this tab stock on Hacer logo, and when I tried to hard reset it takes me to dead andriod, please help me out here, with steps to bring back my tab back to life..thanks

Solution A500 Dead after attempt at reload HC 3.2

Fixed!!! Thanks to Moscow Desire & BlackThund3r, for the leads to the final solution, and obviously bsg19071979 for the actual solution. The partition table was invalid. I ended up using "BadSector" (Had to follow multiple threads on XDA then over to TegraOwners, Then finally back here, to this post "http://forum.xda-developers.com/showthread.php?t=1691729&page=3"
bsg19071979 said:
can be fully corrected sector:
1. Download h??p://narod.ru/disk/53919831001.a235ea2225f319015f30c009629d2075/BabSector.rar.html
2. Run a501 A.bat
3. run recovery 1.7.3 -> "Mount and Storage" -> "Format /system"(better than twice).
4. Run a501 B.bat
Click to expand...
Click to collapse
So can someone tell me what i can do to fix this thing?
I was running Stock ICS 4.03, havn't cared much for it, & wanted to go back to Stock HC 3.2, so tried flashing "Acer_A500_7.006.03_COM_GEN1" from A500 Dev forum. (followed directions, but it would just give the android, on his back, with red exclamation point, then re-boot back into 4.03.)
Read somewhere that I should try using the update.zip file from within the archive directly (rather than renaming "SD_Acer_A500_7.006.03_COM_GEN1.zip" to "update.zip"
Tried that, seemed to work fine, then screen went blank when update was nearly finished, and now can only boot tablet in APX mode. (Lost recovery??)
I have tried replacing lost recovery using APX_v0.4A-flashTool-500Manager1.0.2, The manager says it detects the tablet in APX Mode, but when I try logs, it either just stalls at "Waiting for tablet" or says "No device connected"
Tried to install "EUUs_SBK_Acer_A500_1.016.05_COM_GEN1" (HC 3.01) and it will actually put the tablet into download mode, but will go no further. (At least I can see that the tablet's screen is capable of doing something, as opposed to just being black!)
Any Idea's what will get this tablet going again?
EDIT: Using APXFlash tool, for some reason, on 2 different computers, the text on the buttons doesn't show up, so, The only button I could see was "Dump My BCT", when I clicked it, I would get the BCT file not found message.
I found a tutorial (that showed where all the buttons were & wgat they say, & just used the default BCT. Still cannot get past the "Flashing Bootloader (EBT) stage two - uploading image..." message... nothing is happening, just stalled. Still need some direction...
Thanks
In short, being on stock ICS you also had the ICS bootloader and cannot just flash back to any earlier version. Most likely you now have several pieces of different ROMs embedded on your tab. Take a look at TimmyDean's excellent tutorial which will take you back to v3.2.1 and allow OTA updating: http://forum.xda-developers.com/showthread.php?t=1516012
Goodluck!
amphi66 said:
In short, being on stock ICS you also had the ICS bootloader and cannot just flash back to any earlier version. Most likely you now have several pieces of different ROMs embedded on your tab. Take a look at TimmyDean's excellent tutorial which will take you back to v3.2.1 and allow OTA updating: http://forum.xda-developers.com/showthread.php?t=1516012
Goodluck!
Click to expand...
Click to collapse
So, this is pretty much the same thing I was trying with the EUU file from Acer, and produces the same result. It goes as far as saying "Upgrade is under way. It may take more than 10 minutes." Then it appears to start flashing, (The progress bar starts to move) then errors out with the message "We are sorry! The upgrade process failed. Please follow the instructions for recovery" ( So, what exactly are the instructions for recovery?)
A note maybe worth mentioning, this Tab is stuck in APX mode, so when I get the prompt to enable USB Debugging, I am not aware of a way to enable it, also understood we didn't need that as we are using APX mode?
As well, I know I have the right CPUID, as I looked it up before starting the flashing process, and have just now verified it by liiking with USBDeview.
I am using 0380620044400497.
So, after conneccting the tablet, but before running the flash update, I opened a command window, & ran ADB devices. Got the following output:
adb server is out of date. killing...
* daemon started successfully *
List of devices attached
Notice there are no attached devices, yet As I mentioned earlier, I do not know of any way to turn on USB de-bugging, and I am in APX mode, so I shouldn't expect to see a device through ADB, Correct?
So, is this going to work at all trying to load a bootloader/recovery if I cannot turn on USB de-bugging?
Sorry, again, Any thoughts?
Danny2 said:
So, this is pretty much the same thing I was trying with the EUU file from Acer, and produces the same result. It goes as far as saying "Upgrade is under way. It may take more than 10 minutes." Then it appears to start flashing, (The progress bar starts to move) then errors out with the message "We are sorry! The upgrade process failed. Please follow the instructions for recovery" ( So, what exactly are the instructions for recovery?)
A note maybe worth mentioning, this Tab is stuck in APX mode, so when I get the prompt to enable USB Debugging, I am not aware of a way to enable it, also understood we didn't need that as we are using APX mode?
As well, I know I have the right CPUID, as I looked it up before starting the flashing process, and have just now verified it by liiking with USBDeview.
I am using 0380620044400497.
So, after conneccting the tablet, but before running the flash update, I opened a command window, & ran ADB devices. Got the following output:
adb server is out of date. killing...
* daemon started successfully *
List of devices attached
Notice there are no attached devices, yet As I mentioned earlier, I do not know of any way to turn on USB de-bugging, and I am in APX mode, so I shouldn't expect to see a device through ADB, Correct?
So, is this going to work at all trying to load a bootloader/recovery if I cannot turn on USB de-bugging?
Sorry, again, Any thoughts?
Click to expand...
Click to collapse
Edit: I just ran this again, tried loading an ICS bootloader this time, & noticed there is an error message earlier on in the execution that I previously missed. Please see attached Screen1 (screenshot)
Error is right after bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: partition table is invalid, missing required information (code: 14)
message: nverror:0x4 (ox4) flags: 0
So, I used BlackThund3r's NVFlash, running in a command window, & captured the screen output in the attached .jpg. NVFlash starts, Attempts to format partition 4, then errors out with the message
"Command Execution failed cmd 13, error 0x12002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
NvFlash started
[resume mode]
Thats it, she hangs here & refuses to go further.
This mean anything to anyone?
Danny2 said:
Edit: I just ran this again, tried loading an ICS bootloader this time, & noticed there is an error message earlier on in the execution that I previously missed. Please see attached Screen1 (screenshot)
Error is right after bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: partition table is invalid, missing required information (code: 14)
message: nverror:0x4 (ox4) flags: 0
So, I used BlackThund3r's NVFlash, running in a command window, & captured the screen output in the attached .jpg. NVFlash starts, Attempts to format partition 4, then errors out with the message
"Command Execution failed cmd 13, error 0x12002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
NvFlash started
[resume mode]
Thats it, she hangs here & refuses to go further.
This mean anything to anyone?
Click to expand...
Click to collapse
Fixed!!! Thanks to Moscow Desire & BlackThund3r for the leads to the final solution. The partition table was invalid. I ended up using "BadSector" (Had to follow multiple threads on XDA then over to TegraOwners, Then finally back here, to this post "http://forum.xda-developers.com/showthread.php?t=1691729&page=3")

[Q] Need Help Recovering - Driving Me Crazy

I have flashed a lot of stuff, but this Iconia is driving me CRAZY.
For starters, the tablet will only boot into APX mode when you turn it on. Blank screen, but the power light is white/blue.
I DO have the SBK, which I grabbed through Ubuntu.
I try using the blackthund3r utility. It detects it in APX mode fine and pops it into the bootloader, but after that it gets stuck. This is at "Flashing Bootloader (EBT) stage two - uploading image..." The command prompt just displays Nvflash started [resume mode].
When I try running v8.bat manually from the command prompt, I usually get a lot of failed command errors which come at different points at times.
The other day I miraculously used the blackthund3r utility and handpicked some bootloader and system files and got it to boot back into Android, but when it tried updating OTA it got stuck on reboot saying the "blob update failed." Now I am back to the start of this post.
I've updated the drivers a few times and also installed the Android SDK. Everything is up to date.
If anyone has any idea what might be holding me up I could use the help. My girlfriend is mad now that I have re-destroyed her tablet after bringing it back to life and I need to get it back to her.
Have you tried using Ubuntu to run the nvflash commands, some have had luck with it where windows won't....
Srbeens guide (its stickied in the general forum) to recovering sbk via Ubuntu also has a few steps in running the nvflash commands directly from Timmy deans v4 EUU which is used to repair partitions, there might be something there u can use...
Sent from my GT-I9300 using Tapatalk 2
dibb_nz said:
Have you tried using Ubuntu to run the nvflash commands, some have had luck with it where windows won't....
Srbeens guide (its stickied in the general forum) to recovering sbk via Ubuntu also has a few steps in running the nvflash commands directly from Timmy deans v4 EUU which is used to repair partitions, there might be something there u can use...
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
This is working for me up to the same point. I'm getting a "sync failed (bad data)" error and I can't format any partitions.
erndixon said:
This is working for me up to the same point. I'm getting a "sync failed (bad data)" error and I can't format any partitions.
Click to expand...
Click to collapse
k, hopefully its just your partitions messed up and not the dreaded hardware failure... you got couple options left and both of these will work from apx mode
timydeans v4 an EUU based tool which will give you a pre-rooted stock HC3.2 and cwm installed too - it will wipe everything
heres how user lcd047 went about it on his a501 but will work for a500
lcd047 wrote:
"I downloaded timmyDean's root-3.2.1-V4.7z
I booted the tablet (in APX mode) and I connected the USB cable to it
in the directory root-3.2.1/Image I run the command
nvflash --bct flash.bct --setbct --odmdata 0x100c0105 --configfile flash.cfg --create --bl bootloader.bin --sbk (your sbk number after converting your UID number) 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX 0xXXXXXXXX --go
without rebooting, I flashed the v7 bootloader and recovery as per the bootloader thread; since the partition table was restored at the previous step, the operation now succeeded;
I rebooted the tablet in recovery, and proceeded to wipe the data and flash a ROM the usual way.
And that worked for me. After flashing, my a501 did a automated reboot, i quickly killed the reboot by holding the Power Button (guessing killing the reboot is not realy necessary because the booting shouldn´t mess up the partition table again) and then brought the devive back to APX Mode (Holding Reset and Power for 3-4 sec. then releasing Power and after 1 second relesaing Reset).
Then i flashed the hacked bootloader via blackthund3rs APX flash tool (see link above).
Then i installed Alexandra V as Moscow Desire descirbes (see "To Install" at http://forum.xda-developers.com/show....php?t=1635577)
It took my 2 days of trial and error, but finaly give me a nice working Alexandra ROM on my a501!
Click to expand...
Click to collapse
The other way is by using the "babsector.rar" from the russian forums -
you can download it http://forum.xda-developers.com/showthread.php?t=2049778, theres a couple of good links in post 13 of that same thread on how to use it correctly
You don't say which rom was on the tab previously - so once the partitions are repaired and you've run the unlocked bootloader flash you'll need to immediately boot to recovery and flash an ics/jb rom ...do not try booting into android until you have done this....else you'll need to do everything all over again!!!
dibb_nz said:
k, hopefully its just your partitions messed up and not the dreaded hardware failure... you got couple options left and both of these will work from apx mode
Click to expand...
Click to collapse
Very helpful threads. Exactly the problems I was facing. Using the babsector a501a commands, I am getting a "create failed: (bad data)" and "bootloader status: fatal failure to read/write to mass storage" errors right after it creates the partitions. I am guessing that it is probably faulty memory then and it just can't write to it no matter if I am doing it correctly or not. Thanks for all your help.
erndixon said:
I am guessing that it is probably faulty memory then and it just can't write to it no matter if I am doing it correctly or not. Thanks for all your help.
Click to expand...
Click to collapse
try this: http://forum.xda-developers.com/showthread.php?p=49951540

Cannot install custom ROMS or unlock bootloader [SOLVED]

I have been trying with every guide and every video I've found to install a custom ROM (CM10 FLEX). Youtube videos generally tend to leave out the fact that you need to unlock the bootloader first. So I go to bootloader guides and follow those and nothing seems to work.
I have attempted to use Blackthunder's Manager and Flasher tools to get it working and something always hangs or gets stuck. With Blackthunder's app it was stuck at the "uploading image" phase. Same goes for AfterOTA.
I'm sorry I'm being vague, but it'll be hard for me to type out every scenario and every program I've tried since I literally just spent 3 evenings and about 6 hours trying with this. My google results are all red because I've looked at every thread already and every guide.
So I'd like some fresh advice and opinions. Where should I start? It's a rooted A500 running ICS (from the standadrd acer update) and is pretty much stock
If a500 manager hangs u will need to flash manually using nvflash.
Civato has a guide stickied in dev forum.
Basically download the v8 bootloader.zip file, extact it, put yr tab in apx mode and run the .bat file.
You will have the option to flash a custom recovery along with the v8. After the flash boot directly to cwm and flash yr rom! Done...
Sent from my GT-I9300 using Tapatalk 4
dibb_nz said:
If a500 manager hangs u will need to flash manually using nvflash.
Civato has a guide stickied in dev forum.
Basically download the v8 bootloader.zip file, extact it, put yr tab in apx mode and run the .bat file.
You will have the option to flash a custom recovery along with the v8. After the flash boot directly to cwm and flash yr rom! Done...
Sent from my GT-I9300 using Tapatalk 4
Click to expand...
Click to collapse
NVflash fails too. It gets stuck on:
Nvflash started
[resume mode]
and after 30 minutes....nothing.
TurnNBurn said:
NVflash fails too. It gets stuck on:
Nvflash started
[resume mode]
and after 30 minutes....nothing.
Click to expand...
Click to collapse
And you're running the bat file from apx mode and yr tab is displaying
Acer iconia downloadmode??
The flash should takeno longer than 5mins total.
If its stalling here check apx device is showing in device manager or under safely remove
Hardware icon in the system tray. Do u have adb/fastboot installed. They come with
the android sdk or u can d/l them from the rootguide in my sig.
Do u see the system info window at all does it stall after/before this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
dibb_nz said:
And you're running the bat file from apx mode and yr tab is displaying
Acer iconia downloadmode??
The flash should takeno longer than 5mins total.
If its stalling here check apx device is showing in device manager or under safely remove
Hardware icon in the system tray. Do u have adb/fastboot installed. They come with
the android sdk or u can d/l them from the rootguide in my sig.
Do u see the system info window at all does it stall after/before this:
Click to expand...
Click to collapse
It was running in APX mode and the A500 was showing that it was in APX mode. How would you recommend I get into APX mode? I ask because I've seen various guides that have different ways. The only way I was able to get into APX mode was using Blackthunder's flashing tool and when the A500 was in APX mode I used the other tool (while abandoning blackthunder's tool) to try and flash it.
dibb_nz said:
If its stalling here check apx device is showing in device manager or under safely remove
Hardware icon in the system tray. Do u have adb/fastboot installed. They come with
the android sdk or u can d/l them from the rootguide in my sig.
Click to expand...
Click to collapse
Sent from my GT-I9300 using Tapatalk 4
dibb_nz said:
Sent from my GT-I9300 using Tapatalk 4
Click to expand...
Click to collapse
The device manager wasn't showing an APX device and neither was the "safely remove hardware" tool, but the tablet was still showing it was in APX mode.
I just now tried the "AfterOTA" tool and the tablet says it's in APX mode, but the tool has been stuck on "3/5 Flashing kernel" for about 5 minutes now.
While it was in APX mode again I tried starting the Blackthunder tool. After it failed to start the first process, I closed the command prompt window and it appeard to continue through the process. It got to the "Flashing Bootloader (EBT) stage one - formatting partition..." stage, and in the command prompt it said, "Formatting partition 4, please wait..." but after about 10 minutes....nothing.
Upon a reboot nothing has changed. My tablet isn't bricked and the SD card contents are fine. While it said it was formatting the partition and throughout this process I didn't see anything about "APX" devices in the "safely remove hardware" tool or in the device manager. Though I think I do require a reboot, as now my flash drives arent even showing up in the "remove hardware" tool.
I tried the blackthunder tool again, and I still don't see an APX device in "Device manager". Before it enters APX mode I see an ADB device. But when the blackthunder app says it's in APX mode (Acer screen is completely black) I don't see an APX device in device manager.
However, when I proceed to the next step using blackthunder's tool, I get a green "Acer" logo and in the upper left corner it says, "acer iconia apx mode." And this is where it gets stuck. The black command prompt says, "NVflash started [resume mode]" and the blackthunder program says, "flashing bootloader (EBT)- stage two - uploading image.
I do have the entire android SDK (latest as of 14 Sep 2013.) So I do have adb/fastboot.
K m8 - something is defo amiss -download babsector.rar in the root guide. This will reset yr partitions and flash bootloader and recovery. It will also detect and display any errors.
When u r having probs like yrs it is best to put ye tab inapx mode via the button combo and flash manually, pls post the output of commands....but I have to say its sounding suspiciously like yr memory chip is faulty...we will know for sure once you've run babsector!
Sent from my GT-I9300 using Tapatalk 4
dibb_nz said:
K m8 - something is defo amiss -download babsector.rar in the root guide. This will reset yr partitions and flash bootloader and recovery. It will also detect and display any errors.
When u r having probs like yrs it is best to put ye tab inapx mode via the button combo and flash manually, pls post the output of commands....but I have to say its sounding suspiciously like yr memory chip is faulty...we will know for sure once you've run babsector!
Sent from my GT-I9300 using Tapatalk 4
Click to expand...
Click to collapse
I downloaded babsector, but it looks just like nvflash. Are they the same tool?
Also, I have never once gotten the tablet into APX mode using the manual method (power + reset button, right?). Every time I hold the power and reset button, wait for it to reboot (3 seconds) and release the buttons (power button first) it just powers up like normal.
-edit-
Also, I've been searching for a while now and I can't seem to find a guide showing how to use babsector. Do you have a link handy? What guides I did find said to run "A501 A.bat" first, and when I do that it asks for my SBK and then says "nvflash started. No usb devices found. Press any key to continue..."
My question will sound odd, but from what I've read above, it looks like your computer doesn't see your tab in APX mode:
TurnNBurn said:
The device manager wasn't showing an APX device and neither was the "safely remove hardware" tool, but the tablet was still showing it was in APX mode.
Click to expand...
Click to collapse
I remember mine seeing it when I was under APX mode, are you sure you have the right drivers installed ? I would not proceed any further until the comp sees the tab under APX.
mouhii said:
My question will sound odd, but from what I've read above, it looks like your computer doesn't see your tab in APX mode:
I remember mine seeing it when I was under APX mode, are you sure you have the right drivers installed ? I would not proceed any further until the comp sees the tab under APX.
Click to expand...
Click to collapse
yes, the proper drivers are installed. I believe the issue isn't related to the tablet, but something in windows (a service, maybe) that I disabled.
I got the tablet into APX mode using blackthund3rs A500 manager, ran babsector, and here's the output:
Code:
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c620742bfa4d7
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
creating partition: PT
creating partition: APP
creating partition: EBT
creating partition: GP1
creating partition: SOS
creating partition: LNX
creating partition: CAC
creating partition: MSC
creating partition: FLX
creating partition: AKB
creating partition: UDA
creating partition: GPT
Formatting partition 2 BCT please wait.. done!
Formatting partition 3 PT please wait.. done!
Formatting partition 8 APP please wait.. done!
Formatting partition 4 EBT please wait.. done!
Formatting partition 5 GP1 please wait.. done!
Formatting partition 6 SOS please wait.. done!
Formatting partition 7 LNX please wait.. done!
Formatting partition 9 CAC please wait.. done!
Formatting partition 10 MSC please wait.. done!
Formatting partition 11 FLX please wait.. done!
Formatting partition 12 AKB please wait.. done!
Formatting partition 13 UDA please wait.. done!
Formatting partition 14 GPT please wait.. done!
done!
sending file: bootloader_v8_green.bin
| 1191932/1191932 bytes sent
bootloader_v8_green.bin sent successfully
sending file: recovery.img
/ 5242880/5242880 bytes sent
recovery.img sent successfully
Press any key to continue . . .
and now my tablet says, "entering acer download mode"
and "PASS" in big letters.
-edit-
upon rebooting the tablet it came up with a skrilax bootloader. I entered recovery mode since the primary and secondary kernels failed. I was able to follow the usual guides and install the ROM. However, now it wont boot. It just gets stuck at the bootloader since there's no valid kernel image. What now?
-edit-
Looks like it was messed up partitions. The fix was to put the tablet into APX mode, run babsector, and then proceed as normal.
I tried installing the ROM again and it worked fine this time. It's loading up now. But it's stuck on the "android" screen with the flashing animated "android" text. It's been doing this for about 5+ minutes now. How should I continue?
-edit-
I tried another ROM since I am able to get to the recovery console. I tried CM-10 unofficial (before it was CM-10 FLEX). I get the animated cyanogenmod loading screen and then nothing. It just sits here loading.
Well from what I remember, when I encountered that kind of problem on my devices, I made a total wipe and reprocessed the installation.
Just to be sure I would under fastboot do:
fastboot erase userdata
fastboot reboot
then under recovery, wipe factory and format flexrom. then re install.
Hope this helps.
mouhii said:
Well from what I remember, when I encountered that kind of problem on my devices, I made a total wipe and reprocessed the installation.
Just to be sure I would under fastboot do:
fastboot erase userdata
fastboot reboot
then under recovery, wipe factory and format flexrom. then re install.
Hope this helps.
Click to expand...
Click to collapse
I did do total wipes before each install. I wiped the cache, did factory resets, and wiped the delvik cache.
When I try "fastboot erase userdata" it just says "waiting for device". I am at the CWM Recovery v5.5.0 main menu. Which mode should the tablet be in?
TurnNBurn said:
I did do total wipes before each install. I wiped the cache, did factory resets, and wiped the delvik cache.
When I try "fastboot erase userdata" it just says "waiting for device". I am at the CWM Recovery v5.5.0 main menu. Which mode should the tablet be in?
Click to expand...
Click to collapse
First you need to be in fastboot mode, instead of going into CWM by pressing "volume down" while it's booting, press "volume up" and choose fastboot mode.
Also if you have an error message while doing that, maybe you'd like to take a look here: http://forum.xda-developers.com/showthread.php?t=1431907
mouhii said:
You need to be in fastboot mode first, instead of going into CWM by pressing "volume down" while it's booting, press "volume up" and choose fastboot mode.
Also if you an error message while doing that, maybe you'd like to take a look here: forum.xda-developers.com/showthread.php?t=1431907
Click to expand...
Click to collapse
That did it. I didn't know about the volume up option. I did the fastboot stuff, cleared the cache and did a factory wipe, re-installed CM-10 unofficial, and I just rebooted 8 minutes ago (I'm timing it.) still nothing. Just the cyanogenmod logo with the animated swirl going around in circles.
TurnNBurn said:
I did do total wipes before each install. I wiped the cache, did factory resets, and wiped the delvik cache.
When I try "fastboot erase userdata" it just says "waiting for device". I am at the CWM Recovery v5.5.0 main menu. Which mode should the tablet be in?
Click to expand...
Click to collapse
there are 2 bat files with babsector.
after running the first one, you reboot to recovery and do a full wipe.
there is an option to "enable data/media" do that and it will fully wipe your device. I think its in the mounts and storage menu.
Once you do that flash your rom.
On reboot you must see "skrilqx_cz unlocked bootloader" displayed on-screen
If you don't have this then fastboot will not be available.
Rerun either babsector or the v8/v9.
To enter apx mode manually - You must be sure you are holding in the reset button...otherwise your tab will boot normally as you have found - using a paper clip ( or anything "non-pointy ended ) you will feel the button push in.
(Try holding the tab on its edge on your lap with the power button on your left and the reset button on top)
Press in and hold the reset button
Then press and hold the power button for about 3 seconds.
Then after a second or so release the reset button.
The time part isnt critical, its the delay between releasing the buttons thats important AND having the reset button puched in.
Once skrilax_cz is installed, you can enter "fastboot" by pressing power/vol up
Choose fastboot from the menu ( there may even be an option on the menu to wipe)
Connect your tab to yr pc and open a command prompt on the fastboot folder.
Enter your erase commands and then "fastboot reboot".
Oh and also - u said you were running stock ICS - if you lose your custom recovery and end up with the dead android screen, you will have to delete the .boot.p file as stated in the guides.
I don't know if I'll be able to help you much more than that as I never faced that problem (well that one persisting never happened to me on the Iconia, it did on the SGS i9100 but it was because of a faulty kernel)
You could try to flash first a rom like the one from civato, RE-FLEXxx-ShellSHOCK, see how it goes, also are you formating flexrom ? (from advanced in CWM), it helped sometimes.
Btw I'm using CWM public recovery v0.2 (based on CWM 5.5.0.4, there's a thread in dev section), along with bootloader V8. Never had a problem using any rom with this one.
--edit
My bad, I said flexrom format was in advanced, it's in mount/storage menu.
TurnNBurn said:
That did it. I didn't know about the volume up option. I did the fastboot stuff, cleared the cache and did a factory wipe, re-installed CM-10 unofficial, and I just rebooted 8 minutes ago (I'm timing it.) still nothing. Just the cyanogenmod logo with the animated swirl going around in circles.
Click to expand...
Click to collapse
Power off and reboot...it can take awhile to boot up,
go make a coffee
Sent from my GT-I9300 using Tapatalk 4
---------- Post added at 09:13 AM ---------- Previous post was at 09:02 AM ----------
@TurnNBurn....howzit going????
Sent from my GT-I9300 using Tapatalk 4
dibb_nz said:
there are 2 bat files with babsector.
after running the first one, you reboot to recovery and do a full wipe.
there is an option to "enable data/media" do that and it will fully wipe your device. I think its in the mounts and storage menu.
Once you do that flash your rom.
Click to expand...
Click to collapse
I've only run the first batch file, batch file A.
I finally got it into APX mode, ran batch file A, and reset everything. However, there is no "enable data/media" option under the mounts and storage menu. I have:
mount /system
mount /data
mount /cache
mount /flexrom
mount /sdcard
and then for each mount option I have a format (format /system, format /data, etc...)
If I do have to delete the boot.p file, how is that done?
-edit-
This post was made 30 mintues ago and the cyanogenmod logo is still on the screen swirling after the new flash and reboot.
-edit 2-
45 +/- minutes now. I'm shutting it off again.
-third notoriously annoying edit-
I repeated the steps and tried a different ROM, CM 10 flex again. Still no joy. Been sitting at the animated boot screen for a few minutes now...and coffee is already made since the last ROM reboot.
TurnNBurn said:
I've only run the first batch file, batch file A.
I finally got it into APX mode, ran batch file A, and reset everything. However, there is no "enable data/media" option under the mounts and storage menu. I have:
mount /system
mount /data
mount /cache
mount /flexrom
mount /sdcard
and then for each mount option I have a format (format /system, format /data, etc...)
If I do have to delete the boot.p file, how is that done?
-edit-
This post was made 30 mintues ago and the cyanogenmod logo is still on the screen swirling after the new flash and reboot.
-edit 2-
45 +/- minutes now. I'm shutting it off again.
-third notoriously annoying edit-
I repeated the steps and tried a different ROM, CM 10 flex again. Still no joy. Been sitting at the animated boot screen for a few minutes now...and coffee is already made since the last ROM reboot.
Click to expand...
Click to collapse
ok here we go...grab yr beverage of choice
boot.p file is a file on stock roms that overwrites your newly flashed custom recovery..if you still have cwm you dont need to worry bout it!
The reboot shouldnt take that long - maybe 10mins at most.
You will need to go in and wipe EVERYTHING twice! Yes twice!!
this means System, flexrom, Data and cache. After erasing/formatting System you will not have an OS so be sure to flash a rom before rebooting.
Either fastboot erase or cwm format - (choice is yours but I find fastboot just as easy but its unforgiving..you do not want to muck up in here!!!)
You may want to update to the latest cwm - heres a recovery.img http://forum.xda-developers.com/attachment.php?attachmentid=2238701&d=1378452510
Put it in the folder where you have fastboot. Then boot to fastboot andenter
fastboot flash recovery cwm_1.7.3_recovery.img
EDIT: did u run the 2nd bat file from babsector??

[Q] Stuck in APX mode. No CPU ID. Help.

So I did have a file will all the the information CPUID. SBK. Everything. But now I can not find it (I have apparently deleted it at some point).
I tried flashing a new rom and it bricked my tablet. I also can't boot into recovery because the volume buttons are broken. So all I've got is APX mode. Is there anyway to get out of this with out a CPUID? OR is there a way I am able to find my CPUID when I am not able to boot (and start the ADB service). I have tried everything I can think of and have searched the internet with no results.
I have an acer A500
Luke00123 said:
So I did have a file will all the the information CPUID. SBK. Everything. But now I can not find it (I have apparently deleted it at some point).
I tried flashing a new rom and it bricked my tablet. I also can't boot into recovery because the volume buttons are broken. So all I've got is APX mode. Is there anyway to get out of this with out a CPUID? OR is there a way I am able to find my CPUID when I am not able to boot (and start the ADB service). I have tried everything I can think of and have searched the internet with no results.
I have an acer A500
Click to expand...
Click to collapse
See cpuid guide in my Sig there are 8 methods to retrieve it. Any nandroid backup stores in a txt file in the backup folder.
Not having volume button is gonna add to yr probs if apxflash cannot boot u to apx mode and get u yr cpuid.
If u have the unlocked boot loader you can hook up to yr pc and use fastboot to get u into recovery. Once yr tab is running again install a reboot app or flash a cm Rom which has reboot options in the shutdown menu.
Sent from my HTC_PN071 using Tapatalk
Stuck in APX mode too
Hi guys
This trouble looks like mine ....
I'm going to explain my trouble too (sorry for my English, I'm French ... )
My A500 tablet was stopped in the acer logo page, at begining of the tablet boot.
I tried Volume- and Power, I had an android on the floor with a red triangle.
I found the CPUID with the ubuntu method.
http://forum.xda-developers.com/showthread.php?t=1751978
http://forum.xda-developers.com/showpost.php?p=23783875&postcount=9
I tried to update my tablet with the EUU acer software. At the end of the update, I had the following message : "Congratulations, you have the last version ....." but my tablet still had the message "Entering in the acer download mode" (or something like that)
I restarted my tablet and ..... here's the real trouble !!! My tablet didn't restart, and worst the trouble was very very worst ... no acer logo, no vibes, nothing, nothing, only black screen and power button ON.
Like if I was in APX mode. My tablet is still reconized in windows as Acer Picasse USB device ....
How can I fix my tablet ?
Thanks
See you
KaloOopS
Hold power button in 5secs, light should go off. Power on again
Sent from my HTC_PN071 using Tapatalk
Thanks but ...
... always in stuck in APX mode ...
I'm trying afterOta .. even with this I'm stuck "2/3 flashing memory" .. like sometimes in the EUU software where I am stuck near 8-10% of processus ...
KaloOopS said:
... always in stuck in APX mode ...
I'm trying afterOta .. even with this I'm stuck "2/3 flashing memory" .. like sometimes in the EUU software where I am stuck near 8-10% of processus ...
Click to expand...
Click to collapse
go to the root guide in my sig - download babsector from post 2, the instructions are there as well. Follow them exactly as written. If you receive an error pls post it.
dibb_nz said:
go to the root guide in my sig - download babsector from post 2, the instructions are there as well. Follow them exactly as written. If you receive an error pls post it.
Click to expand...
Click to collapse
Hi
I tried Babsector.
My tablet switched with vibes on to the Acer logo page with the message in the corner on the top on the left "Entering in Acer download mode" ... or something like that.
But it stays on this page ...
here's the command windows log :
Code:
****************************************************************
* Before executing, be sure to delete recovery-from-boot.p *
* from /system to ensure recovery will stick *
****************************************************************
****************************************
* Reboot your tablet into APX mode *
****************************************
Generate your SBK with your CPUID from here :
......
Enter your SBK:0x19B81E00 0xD4E0BA01 0x3BA95E03 0x.....
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x037c61.......
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
creating partition: PT
creating partition: APP
creating partition: EBT
creating partition: GP1
creating partition: SOS
creating partition: LNX
creating partition: CAC
creating partition: MSC
creating partition: FLX
creating partition: AKB
creating partition: UDA
creating partition: GPT
failed executing command 12 NvError 0x120002
command failure: create failed (bad data)
bootloader status: fatal failure to read / write to mass storage (code: 9) messa
ge: nverror:0x8 (0x19000008) flags: 0
Appuyez sur une touche pour continuer...
So what's up doc ?? Any idea pls ...
Thx
KaloOopS
delete the boot.p file m8
Sent from my HTC_PN071 using Tapatalk
dibb_nz said:
delete the boot.p file m8
Sent from my HTC_PN071 using Tapatalk
Click to expand...
Click to collapse
How to do that ???
In the same time, I'm trying APX Flash Utily (following your Sig).
Processus is stuck in the "Flashing Bootloader (EBT) stage two - uploading image..." since 10 mins ...
After about 20 mins, I unplugged my USB cable, New processus message "Flashing Recovery (SOS) stage one - formatting partition..." and after that "Sucess, switch off tab " ... or something like that ...
I switched off my tab, and switch on with a lot of hope ..
And f***, same status, black screen and power light on, APX mode .... grrrrrrrrr
HEEEELP ... lol
thx
EBT error is not good
Wot happens when u hold power button in 5 secs does lite go off
Sent from my HTC_PN071 using Tapatalk
Thanks a lot
Hi Dude Dibb
I succeeded this night to solve my trouble.
After using APX tool flash, I played again with the BabSector by changing bootloaders, recovery and flash.Cfg
Of course same kind of messages in the command window.
No mistaches !!
I tried with my last bootloader and recovery came from the ....013..GEN1 .. (sorry I'm writing from my office so I don't have all params .. )
And here, miracle !!!! I had the famous message above the Acer logo : "P A S S" ...
After that I used the EUU software and flashed my tab... switched off
switched on and here's the HoneyComb !!!!!
next step I have to upgrade it into ICS .. but I think it would easier (any easy method, EUU or Acer application or anything else) .. I hope ...
thank for your help again
see you
KaloOopS
oops **** my boss ... byyyyyyyyyyye :angel:
dibb_nz said:
See cpuid guide in my Sig there are 8 methods to retrieve it. Any nandroid backup stores in a txt file in the backup folder.
Not having volume button is gonna add to yr probs if apxflash cannot boot u to apx mode and get u yr cpuid.
If u have the unlocked boot loader you can hook up to yr pc and use fastboot to get u into recovery. Once yr tab is running again install a reboot app or flash a cm Rom which has reboot options in the shutdown menu.
Sent from my HTC_PN071 using Tapatalk
Click to expand...
Click to collapse
Ok. Thank-you very much! I was actually able to find it in an archive (I had written it down in the past, but couldn't find the file) Making lots of backups this time.
grrrrrrrrrrrrrrrrrrrrrrrrrrr
dibb_nz said:
EBT error is not good
Wot happens when u hold power button in 5 secs does lite go off
Sent from my HTC_PN071 using Tapatalk
Click to expand...
Click to collapse
Hi Dibb,
Of course, if I hold the power button, my tab switches off.
But, now I have again the trouble.
As I told in my last post, I succeeded to install the EUU software and have the HC 3.0.1.
But I did the official updates by ICONIA TAB Update Enhancement from the 1.016.05-COM-GEN1 to the 7.014.01-COM-GEN1 (HC 3.2.1) without troubles. At this step no more official update.
I updated the ICONIA TAB Update Enhancement, and it found me a new one : 041.203.01-COM-GEN1 (I thought it was the ICS one), so I did it.
And my troubles came back !!!
My tab stucks on the ACER logo page. So I tried to update the bootloader. Since this moment I can't anymore launch the nvflash.exe. Each time, with any bootloader I have some error logs after creating partitions :
Either : formatting partition 2 bct please wait.. failed
or : bootloader status fatal failure to read / write to mass storage (code 9)
How can I do to downgrade to HC and install it again ?
Any precision : I tried APX Flash and AfterOTA without success ....
Thx a lot
CU
KaloOopS
KaloOopS said:
Hi Dibb,
Of course, if I hold the power button, my tab switches off.
But, now I have again the trouble.
As I told in my last post, I succeeded to install the EUU software and have the HC 3.0.1.
But I did the official updates by ICONIA TAB Update Enhancement from the 1.016.05-COM-GEN1 to the 7.014.01-COM-GEN1 (HC 3.2.1) without troubles. At this step no more official update.
I updated the ICONIA TAB Update Enhancement, and it found me a new one : 041.203.01-COM-GEN1 (I thought it was the ICS one), so I did it.
And my troubles came back !!!
Click to expand...
Click to collapse
The Update enhancement tab IS ONLY FOR upgrading FROM HC to ICS. THe bootloaders are very different between HC and ICS, so, once you are on ICS you sorta have to stay there. you cannot flash an HC rom from ICS, you need to do a downgrade.
Either, do a full downgrade back to 1.016.05 it should give you an update straight away to 4.xxx.xx, if not just flash the v8 unlocked bootloader from there, unless you want Acer Stock ICS
AfterOTA won't work unless you have completed the full OTA update process.
ApxFlash tool is the only tool that repairs bct error, its not very good at it once you have received that error as I posted earlier -
KaloOopS said:
Hi Dude Dibb
I succeeded this night to solve my trouble.
After using APX tool flash, I played again with the BabSector by changing bootloaders, recovery and flash.Cfg
Of course same kind of messages in the command window.
No mistaches !!
I tried with my last bootloader and recovery came from the ....013..GEN1 .. (sorry I'm writing from my office so I don't have all params .. )
And here, miracle !!!! I had the famous message above the Acer logo : "P A S S" ...
After that I used the EUU software and flashed my tab... switched off
switched on and here's the HoneyComb !!!!!
next step I have to upgrade it into ICS .. but I think it would easier (any easy method, EUU or Acer application or anything else) .. I hope ...
thank for your help again
see you
KaloOopS
oops **** my boss ... byyyyyyyyyyye :angel:
Click to expand...
Click to collapse
can you guie step by step how did you change bootloaders, recovery and flash.Cfg as the tablet is not workable, sorry im new to this, also where is this boot.p file to delete?

Categories

Resources