[GUIDE] New unbrick guide compilation - Acer Iconia A500

I’ve been helping a buddy get his A500 back to working order, so I thought I’d add the steps taken here which lead to successful replacement of boot loader and ability to flash roms again.
First off Blackthun3r is a genius and you cats should totally donate and thank him if this stuff helps.
The info is a bit spread out so I hope this helps consolidate things. We all owe big ups to jnktechstuff for starting this post here:
http://forum.xda-developers.com/showthread.php?t=1699277 go thank him too.
One thing everyone is right about: You must secure your ID just in case, which is needed to properly reprogram the stock/crappy recovery boot. Two options I saw:
1) From a nandroid backup (inside the clockwork recovery folder or wherever your previous bootloader stored them) there is a uid.txt file.
2) When you run Afterota if it can’t find a uid it will generate a file “AcerIDs.txt”.
Afterota is great too but wouldn’t fix/attached to our A500 in APEX mode, but this feature alone is huge.
For AfterOTA, Thanks and Salute to Gersma:
http://forum.xda-developers.com/showthread.php?t=1675939
Next is just getting the thing to boot.
http://forum.xda-developers.com/showthread.php?t=1699277
Mentioned in “How to unbrick” , as stated they suggest you get 3 files. Here’s what we got :
1) Decrypter (mandatory)
2) 2 ICS roms (you only need one, but he suggests to get both just in case, or even an older Honeycomb if those fail you).
The one that worked for us was ICS 4.0.3: 7.014.01_41.203.01.
Extract the decrypter and use on the rom/zip you downloaded. It will make a separate rom/zip with the words ‘decrypted’ at the end. EXTRACT THIS FILE!
Inside the newly extracted zip file should be 3 files. If you don’t have it or your zip program says it’s corrupted then you don’t need to decrypt it, use the non-encrypted version of the rom pack you just downloaded (i.e. it wasn’t encrypted)!
3 files will look like:
1) Update.zip
2) AMSS.zip
3) Acer_A500_7.014.01_041.203.01_COM_GEN1.txt (or whatever rom you had downloaded)
These 3 files need to be on the root of your external SD micro card (either put it into a reader for pc access or if your system is functional copy it over via USB cable while mounted in the A500). The basic bootloader does nothing but check for an update.zip and apply it. However, it cannot replace itself (saw with a CWM or TWRP) and thus what I think is the ‘rub’ with this device.
After the update.zip applies, boot the system normally. You should have a locked OTA version of ICS with USB Debugging enabled, if not, hit Options, Developer and turn on USB Debugging. If it doesn’t boot, try another rom/decrypt combo. If it boots moved these three files into a sub folder on your SD Card and save for next time you brick it
Next, get the right driver for Windows from Acer site (this is important because it has the ICS USB and the APEX/boot USB driver needed):
http://www.acer.be/ac/nl/BE/content/drivers
You now need to unlock, add SU and Super User. Hit the following link and get Blackthund3r’s Root app (ICS7.1.x for Windows) top of page:
http://forum.tegraowners.com/viewtopic.php?f=30&t=350
When you hit some of this download links be sure to check for things like the skip ad button top right corner, else you’ll download the wrong thing:
Extract and run “ICS Root 2.exe”
1) DO NOT mess with the bundles tabs right now, but ensure all checks minus bottom two are selected and ‘Do it!’
2) You should see that it does confirm for you that it is connected and USB Debugging turned on.
You should now have the device setup to run a proper APEX adjustment, which lets you replace the bootloader and then apply all the little zips and roms your heart desires. Blackthund3r has the last tools we need:
Get APXFlash: http://a500bootloaderflash.tk/#download-links (again watch out for the adfly and click skip add to get to your zips).
APXFlash has all the bundles from proper Blackthund3r repository, the FAQ below may have suggested certain types but that info is kinda old SO just grab a bundle 15, 16 or whatever you are looking for (16 is a great team wiz recovery version combo Skrilax has done, we used that one).
1) Go to Bundle Market and follow the wizard:
2) After downloading the bundle of choice you’ll now be prompted to put in your SBK number from that Acer ID or uid txt file.
3) You should then back up your dump file as it is recommended in the process.
4) Hit blue arrow ‘next’ to see your flash options below, we used the Automatic method, smooth as butter.
5) Follow the prompts for APX mode and click blue once the device is blacked out and the mode has changed on status. This is where that official Acer driver comes in handy.
6) Complete the process as instructed and you’ll be good to go!
Last tool used is:
A500 Manager: http://a500bootloaderflash.tk/#download-links (again watch out for the adfly and click skip add to get to your zips).
This app rocks to help you get into recovery mode (or test your new bootloader) until you get a rom on there that allows you to do it from the power off button or notification tray.
Most of these links and info are at the bottom of Blackthund3r’s FAQ page, which were also super helpful:
http://a500bootloaderflash.tk/
Again this helped my friend and he was thinking several of you could benefit. Even when typing this up I figured some better/quicker ways to maybe get some of the data but this is the thorough steps we took and I hope it helps you! I also had screen caps so once I figure out how to add those, if it'll help or someone needs it will look into that ;p

Related

Dummy's Guide to update your I9000 from the stock software to the Official Froyo

After successfully;
researching, upgrading to the official build of my choosing, getting it to work and typing this tutorial out (for those that like me weren't knowledged in this),
I stumbled across this thread. I thought I should also share it here aswell.
Here's a N00b's (Dummy's) Guide to how to update your device from the stock software to the Official Samsung Froyo ROM (software/operating system) OF YOUR CHOICE!!
Why do this?
You get Froyo. So you get the latest version of Android to support more Apps.
It comes with some UI-tweeks, JIT-compiler, and FLASH 10.1 PLAYER!!!
Also you get a newer (better) kernel on your phone with some of Samsung's fixes for the lag and for the GPS.
You can get features/Apps not available in your native rom build and/or remove the bloatware.
This method (not incl E) can also be used to install custom ROMs (I personally can't wait for the Official English MIUI ROM).
** Denotes steps which I skipped, or was unable/unwilling to follow, or didn't quite understand
Here's the comprehensive, step-by-step, easy-to-follow breakdown/walkthrough (Section E only works on Windows Computers):
A) Remove your microSD card (this will prevent some weid issues later on)
A2) Make sure you have Kies downloaded and installed on your computer
A3) Make sure you have an extractor installed (for Windows 7, winRAR is a great free solution)
B) We need to root your device, for this goto "One Click Root/Unroot" by TGA_Gunnman at http://forum.xda-developers.com/showthread.php?t=742403
B1) Download (2.5MB) the software (depending on your computer, mine is Win7 Home Premium 64-bit) into your computer not phone
B2) Make a folder somewhere in your computer labelled "OneClickRoot" (or anything) and drag the .rar file (the one you just downloaded) into it
B3) Extract the contents of the files by Right-Click then "Extract Here" (If you don't have this option install WinRAR)
B4) Set your phone to USB Debug mode (on your phone goto MENU > Settings > Applications > Developement > USB debugging = Checked) and then connect the phone to the computer via USB cable.
B5) Open the "Galaxy S I9000 One-Click Root" application. (This step didn't work for me, so I instead opened "rootme" batchfile which started the command prompt).
B6) Your phone will shut itself off, and then turn on in a "recovery mode". DO NOT REMOVE THE CABLE. Use the Volume Up and Volume Down buttons to get to "install from " and then hit the Home button.
B7) Now your device should be restarting again but this time it will actually go to your lockscreen.
B8) Now, you have ROOT, Congratulations.
B9) Not sure? We can test to see if you have root. Goto Market on your phone and download two Apps (Superuser and Titanium Backup, use the search to find them fast).
B10) Install both and launch Titanium Backup. As soon as you turn it on it will come up with a pop up and say something like "Your device is not rooted" or "Root is not accessible" ... if you didn't get Root.
B11) If you have root it will say something like "Titanium Backup needs to gain permission from Superuser" here click Apply. If you get to the App, well done you have indeed Rooted your phone
C) Now if you want to Backup your device before the update (recommended) you can follow steps C, otherwise skip straight to Step D.
C1) On Titanium Backup if a pop up notification comes with something like "Download an updated BusyBox" allow it to do so.
C2) Now first thing you will want to backup your Apps (all paid and free and the levels/hiscores) make sure you don't have any emulator ROMs on there (they consume too much space) and delete all those unwanted Apps
C3) On Titanium Backup, hit the Menu button > More > Create "update.zip" ...
C4) On this screen select "User application" and "TitaniumBackup-3.6.2.zip" and UN-TICK the "Sign the ZIP file (with ZipSigner)"
C5) Hit the Create "update.zip"... on the bottom and Please wait
C6) Once it finishes it, exit Titanium Backup, go back to settings and disable USB debugging (as posted on B4).
C7) Connect your phone to your computer (through Kies or PC link) and then browse your My Computer until you find Galaxy S I9000.
C8) Open that folder and then open phone. Find "TitaniumBackup-3.6.2.zip" and copy that to somewhere on your computer.
C9) Now that we have backed up your applications, lets backup your ROM.
C10) According to TGA_Gunnman you can use Clockwork MOD Recovery to do this, but this is for a different (Galaxy S) device ie "Samsung Vibrant"
**C11) Follow the steps on http://forum.xda-developers.com/showthread.php?t=734164 to do so, personally I skipped doing so out of fear of bricking the device (there may be subtle differences between the devices that can make your phone a paperweight/brick)
C12) Now if you did follow the Clockwork MOD, be sure to copy the "update.zip" file somewhere into your computer (better be safe than sorry)
D1) Now we need to apply the 3-Button-Combo Fix (this is the only reason for steps A-C because it is highly recommended to have this before flashing ANY rom)
D2) I recommend the Fix by RazvanG http://forum.xda-developers.com/showthread.php?t=821698 because it seems to be the *safest*
**D3) Firstly check if your device is compatible. I wasn't successful to dump my BML1 block, so I couldn't test if the block reads "[email protected]"
**D3) RazvanG has provided some instructions on this method see his post for more information http://forum.xda-developers.com/showthread.php?p=9595936#post9595936
D4) So I took a leap of faith and continued anyways with the risk of bricking my device. I have it on contract/plan so if it fails I would just return it and say Kies was updating and it failed
D5) I followed the steps on the thread but I'll reitterate it here for your convnieance
D6) Download both files (RAZ-FiX-SGS and adbRecovery) from the thread.
D7) Make a new folder (adbRecovery) on your computer and extract the adb .zip file into there
D8) Connect your phone to the computer and copy the RAZ-FiX-SGS.zip into your phone's memory
D9) Delete the old Update.zip file AND rename the RAZ-FiX-SGS.zip to Update.zip
D10) Again, turn on USB debugging (you know how) and open "Recovery" batch file from your computer
D11) This will initiate a command prompt (on Win7) and restart your phone
D12) Your phone will go into recovery mode (like we've seen before)
D13) You need to navigate (Volume buttons) to "apply sdcard; update.zip" and hit the Home button
D14) Your phone will turn off and restart and should get to your lockscreen
D15) So you're at the lockscreen? SUCCESS! (mine didn't brick *pheww*)
D16) Now let's test to see if the 3-Button-Fix worked
D17) *IMPORTANT* Firstly browse into your phone's internal memory and delete update.zip (the one we put there from RazvanG)
D18) Now that you have done so, you can safely just turn off the device
D19) Hold the Volume Down + Home button ... then hold the power button, as soon as the device begins to turn on release the power button (keep holding Volume Down + Home)
D20) If you get a Yellow triangle with the Android robot and "Do not turn off Target", well done, you have the 3BF so you have a means to ensure that you can always recover your phone if you do brick, well done!
D21) You can *safely* remove the battery and restart your phone ONLY if you don't have a Update.zip in the root of your phone
D22) If you don't want to take a leap of faith try this method (safest method but doesn't work for some people): http://forum.xda-developers.com/showthread.php?t=860773
E1) Now is the fun part (we've just past the difficult parts)
E2) You need to hunt down the version of (official Samsung)software you wish to install ... just go through member's reviews and recommendations
E3) You need to find the product code of that build, you can do this navigating through this thread http://forum.xda-developers.com/showthread.php?t=846913
OR by asking members (they can find out with http://forum.xda-developers.com/showthread.php?t=787163)
E4) For me this was the Virgin mobile Australia build (XSA - an unbadged, no-bloatware, unlocked Froyo build with a free copy of Navigon Navigation)
E5) Make sure you update your Kies to "ver 1.5.3.10103_102" (latest as of the time I'm writing)
E6) Go visit this thread http://forum.xda-developers.com/showthread.php?t=835628 for information (the software may have been upgraded)
E7) Download (300KBs) the Kies Registry patcher 1.6.0.0 (latest as of writing) <<This only works on Windows computers, sorry Mac'ners>>
E8) Launch the Kies Registry Patcher WHEN KIES IS OPENED
E9) Click on File > Backup (and save this somewhere in your computer - this is your original product code - better safe than sorry)
E10) Make Enable Spoof to True
E11) Now where it says "Spoof Product Code as" type in the product code of your desire (mine is XSA)
E12) Hit Write Registry and it should say "Registry pathed successfully"
E13) Connect your phone via USB cable to the computer
E14) On your phone select "Samsung Kies" when the pop up comes ... it should be at the "Connected" screen (DO NOT HIT HOME BUTTON)
E15) On Kies it should find your phone, and a pop up on the corner will say "There is a firmware update available for your phone" hit that pop up
E16) Now you will see another pop up and it's asking if you want to "Back up contacts before upgrading firmware" ... seems like a good idea, tick the box and hit Upgrade
E17) If the screen on the phone shuts (ie standby) don't be alerted. Hit the power button to wake it up. DO NOT HIT THE HOME BUTTON!
E18) Another pop up will come to name the contacts file - I just hit save so its the original filename in original (Samsung)folder
E19) Another Pop up will come to say "Save to PC completed" - hit OK, its just letting you know the contacts saved properly
E20) Now you get another Pop up to start the Firmware Upgrade - This is an important area, note down the: Model Name, Current Version and Latest Version (if something goes wrong this info maybe valuable for developers)
E21) Mine is (model)GT-I9000, (current)PDA:JG4 / Phone:JG3 / CSC:JG2 and (latest) PDA:JP5 / Phone:JP3 / CSC:JP4 ......... notice they are diffirent, this is what I was looking for
E22) Hit Upgrade! (Allow Kies to function when Windows 7 or Windows Vista prompts you)
E23) Tick the "All information has been verified" and Click Next
**E24) Let Samsung record your phone number in their database? I don't care (I'm on insurance/contract/plan) and I hit "Allow saving" ad Clicked Next
E25) Wait patiently, its downloading the rom from the server, DO NOT UNPLUG THE DEVICE
E26) A progress bar will appear, your USB will get disconnected, reconnected several times, the phone will be stuck on the yellow triangle screen - these are normal
E27) The progress bar will slowly be filled from grey to blue and a progress bar will appear on your phone - almost there!
E28) The progress bar on the computer will finish and the pop up will read "GT-I9000 Upgrade completed" - Click Close
E29) Your phone will restart and will enter "recovery mode" some yellow texts will appear and scroll forward
E30) The phone will reboot again and you will see the boot image with the Galaxy S logo
E31) The phone will be stuck on that logo for awhile - be patient
E32) The phone will now get to your lockscreen, unlock it
E33) You will have to go through your initial setup firstly its the Swype tutorial, then data settings, and finally the account settings emerges
E34) If the Kies connection screen comes up: hit the home button
E35) Now you should have come to your Homescreen go and test everything (all your passwords, all your bookmarks, all your contacts, all your images/music/videos and all your apps (except bloatware) should be there but the order of all the widgets/apps in TouchWizz will be reset to abc-order)
E36) Goto Settings > About Phone Does it say Android 2.2?
E37) Well done you have passed Android Hacking 101, you are officially smarter than 50% of iPhone and Blackberry users
E38) Donate me a beer, nah just kidding, enjoy everything for free but feel free to donate to the developers that help make this possible
this is a guide for I9000 international
I9000M owners please be advised that the I9000 might cause you to lose the 850 band, and might also trigger the internal SD problem
AllGamer said:
this is a guide for I9000 international
I9000M owners please be advized that the I9000 might cause you to lose the 850 band, and might also trigger the internal SD problem
Click to expand...
Click to collapse
You made it into a thread, thanks!
Hopefully this might help fellow xdanians
Aww Mate this is awesome, I have the same Carrier and I had OPTUS crap on my Phone from custom roms, Now I'm back to Stock Froyo!!!!
A great tool to Start from afresh.....
But
At Instruction E11 - Select your product code from the drop down Box and it will populate the next field for you.
Gonna put into my favorites
Wow.
I don't think anybody that don't now much would read that.
I know allot and i would never use it either.
You should stick a warning sign on this tread.
I did read about half of it and then i just stop and shake my head.
I hope this tread is a joke.....
Sent from GT-I9000 jpo. My own kernel for z4mod and with 342MB Ram
DamianGto said:
Wow.
I don't think anybody that don't now much would read that.
I know allot and i would never use it either.
You should stick a warning sign on this tread.
I did read about half of it and then i just stop and shake my head.
I hope this tread is a joke.....
Sent from GT-I9000 jpo. My own kernel for z4mod and with 342MB Ram
Click to expand...
Click to collapse
Can you elaborate?
Joke? No it's no joke but I should disclose (as always) this is a tried-and-true way of getting you to update your software but in no way can I be held responsible for damages.
Things may vary slightly in between different phones which is why the links for each source/thread is up there.
I found myself knowing what to do, but always guessing how to do it.
This is a step-by-step process of how and what I did to upgrade my phone to any ROM I want.
If this was posted up before I attempted my upgrade, I would've been so happy that someone really simplified it for me
This is a noobs guide??!!! Simplified??!! I think that everyone will appreciate the time you have spent typing this up and trying to help, but I'm with DamianGto, dude this guide is scary and just explains how YOU got YOUR particular phone running froyo and lets face it, you certainly didn't go about it the easy way!
Once again I think the time you have spent and the willingness to help is admirable, but there are much simpler and noob friendly guides out there
nagrom78 said:
This is a noobs guide??!!! Simplified??!! I think that everyone will appreciate the time you have spent typing this up and trying to help, but I'm with DamianGto, dude this guide is scary and just explains how YOU got YOUR particular phone running froyo and lets face it, you certainly didn't go about it the easy way!
Once again I think the time you have spent and the willingness to help is admirable, but there are much simpler and noob friendly guides out there
Click to expand...
Click to collapse
Well you need root + busybox to get the 3 button fix.
If anything a n00b did, they can recover with 3 button trick otherwise they will have a brick.
This is why this guide is long, to ensure things are a-ok.
If you found a friendlier guide can you post the link, much apprecated ;D
How do I exit downloading mode if I forgot to erase update.zip ?
What is it ? Kies
A2) Make sure you have Kies downloaded and installed on your computer
Thanks
Well I think this is an excellent guide that has great potential!
However, a couple of crucial mistakes, which if fixed could help make the guides less confusing...
At beginning of (D) you talk about (A-C) being solely so you could fix your 3 button download (which I don't think is actually true!)
.... But, you should mention 3 button download at the very start of the guide anyway!!
Also, you should include a quick test at the very start to check for 3 button download, because mine is already fine, so a newbie might run all those extra steps when they already had working 3 button download anyway! (The more sections that can be skipped the better!). You can then steer people to the sections they uniquely will need.
However, titanium backup isn't needed for 3 button download fix, but is a wise step before running a rom update. And this works best with root anyway. Hence I don't think your opener for (D) is very accurate. You didn't just complete those steps JUST to get download mode. The backup was important anyway!
Do others think there should be a stage added for backing up contacts etc?
A stage for backing up efi?
Anything else wise that should be in here?

Galaxy Tab GT-P1010 (WiFi Only) NooB Guide

Galaxy Tab GT-P1010 NooB Guide - Last Revised 2012-02-29
2013-03-09 - SEE POST 9 FOR IMPORTANT INFORMATION
Revisions
2012-02-27 - Initial Publication
2012-02-29 - Added Firmware Download, Thread Consolidation, Custom ROM's, Flashing Stock Firmware and Q&A Section(s)
Post Summary
In this thread I will attempt to outline the details I know of regarding the Galaxy Tab GT-P1010. I feel this is a necessary thread because this device is NOT the same as the various other devices that garner so much attention within this forum and I personally experianced quite a difficult time searching to find the questions to my answers as they releated to this device in particular. While it is my opinion that this device should have it's own sub-forum, I do not believe it is popular enough. This said I feel that it is a fairly solid device and if you are like me, you are somewhat lost in in finding the approriate information. Hopefully this thread will be informative and popular enough that it may get stickied so us lowly 1010 users can find the information they are looking for. I am an active XDA member and will do my best to keep this thread updated as new information & techniques become available. If you see some information that you feel should be included do not hesitate to bring same to my attention and I will update the OP's accordinglly. These Instructions are for use on Windows machines even though I personally use a Mac. If you are in the same boat, I recomend running windows within a Virtual Machine (VM). I use Parallels but VirtualBox is a free alternative. Mac and or Linux only instructions may follow at a later date, but honestly a majority of users use Windows so I'm starting there. Without further a do, let's get started.
GT-P1010 Device Specifications
The GT-P1010 is also know as the "Wi-Fi Only" 7" Galaxy Tab. It differs from a majority of the devices in this forum because it has NO 3G or cellular capabilities. The hardware of the device is also different enough from the 3G/Cellular versions, that the Development going on for these other devices will NOT work for it. The GT-P1010 is unfortunately considered a "forgotten" device and even Samsung has seemingly abandoned providing updates for it. This is particularlly evident within the United States (US), however other Countries, speciffically the United Kingdom (UK) have been seeing updates. For the record I am the owner of a US version and this guide was written using my experiance on that device.
A complete list of specifications can be viewed from Samsung's US Website HERE
MD5 Sums
When downloading files from the internet is extremly important that you verify the download was complete and not corrupted. Insuring this can avoid troubleshooting issues that may simply be because of a bad file. All files available from this post will have an MD5 sum next to them. To verify that your file is EXACTLY the same as the file on the server you will need to run it through an MD5 checker. These checkers are available freely over the internet and Mac OS X even has one built in. I'm not going to make this post about how to run these programs but have included a few links below to get you started. A complete explanation of MD5 Sums can be found at Wikipedia.
WinMD5Free
Drivers - Samsung KIES
In order to perform updates to your P-1010 you need to be able to communicate with the device via a USB cable. While there are stand-alone USB drivers available, I chose to install Samsung's "KIES" application so that I could see if any updates were being pushed directly from Samsung. The KIES program also offers additional functionality to allow you to sync various media on your device. This functionality may or may not be needed for all users but by installing the software you are also guaranteed that the drivers needed to communicate with the device are installed on your machine. The US Samsung KIES site can be accessed HERE but I have included a direct link to the latest Windows Version below.
Kies_2.2.0.12014_18_7 ---- MD5 Sum: 7116aa29ce9df3dc2e916128c9c0aa4c
Download the file and double click it to install KIES and the drivers to you system. Once this is acomplished running the program will present you with a screen similar to the one below:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ODIN
ODIN is a utility that communicates with your device when it is in Download Mode (see below). This utility allows you to flash different firmware and other files to your Galaxy Tab. A screenshot of ODIN running is posted below.
To Run ODIN you will need to download and Un-zip the following file. Once this is acomplished you can run the program by simply double clicking the .EXE file "Odin3 v1.85.exe" which will be inside the un-zipped (extracted) folder. The program does NOT get "installed" and this section is just an overview of the tool. Additional steps on when to use it, and how, will be included in the appropriate sections below.
Odin3-v1.85.zip. ---- MD5 Sum: 414e3af7c4c01e21527aeaab65e68a75
Download Mode
Initiating Download Mode
To communicate with ODIN the device needs to be placed into Download Mode. This is accomplished (from an OFF condition) by holding the Volume Down button + the Power Button at the same time until Download Mode is activated. I have found that the easiest way to do this is to press and hold the Volume Down button and then press and hold the Power Button. Download mode will activate within a couple of seconds and your device will indicate such by presenting you with the following screen. As soon as that happens you can release both buttons.
Exiting Download Mode
If you flash any updated files to your Tab using the procedures outlined below, the device will accept the files and reboot on it's own thereby exiting download mode. If you find that you have entered download mode when you did not intend to use ODIN to flash files, you can EXIT download mode by Holding the Power Button for about 10 seconds. The device will then turn off and when you turn it back on it will boot normally. This can be a little scary considering the warning stating "Do Not Turn of the Target". This warning can be ignored and it is actually telling you not to turn it off while files are being written to it.
Connecting Device to ODIN
To play it safe, I recomend that you try connecting your device to KIES FIRST just to insure that the drivers have been installed properly. If KIES can recognize the device then so can ODIN. Simply open KIES and connect the device to your computer via the USB cable. Once you see that KIES is communicating with the Tab you can close KIES and disconnect the Device from the USB. This will only need to be done once, again, just to make sure the communication is working. Once you are satisfied that it is ....
Run ODIN by double clicking the executable file as outlined above. Place the device in download mode as outlined above. Connect the device to the computer using the USB cable. You will then notice that ODIN has found and is communicating with your device because the ID:COM field will turn yellow and assign a COM port to your device. This COM port will vary by user so don't be alarmed if you personally don't see "COM5" as shown in the screenshot below. As long as this field turns yellow you are good to go.
Recovery Mode - Stock
A stock Tab has a built in recovery mode that will allow you to perform a factor reset on the device and other "maintenance". This mode is entered (from an OFF condition) by holding the Volume Up button + the Power Button at the same time until you see the Samsung Logo, then Release the Power button but continue to hold the Volume up button until Recovery Mode is activated and your device presents you with the following screen. As soon as that happens you can release the Volume Up button. Once Recovery is activated you can toggle through the menu items by using the Volume up & Volume down buttons. To execute a selection use either the Power OR Home Button. It is the Power button on my device but this apparently varies on some models.
Rooting
If you are here on XDA then you are probably interested in "Rooting" your device. Rooting has many advantages and certain Market Applications will only work if you have these Root Powers. The US version of the Stock GT-P1010 is currently running the Froyo version of the Android Operating System. A Gingerbread version has not been officially released and may never be. We will deal with upgrading to Gingerbread later in the Tutorial. For now, if you want to Root your device running Froyo (My device had Build: Froyo.UEKC6), you can follow these steps:
1. Download the application Z4Root from the following link:
Z4Root.1.3.0.zip ---- MD5 Sum: 077974421412b25089289acdc763b1c1
2. Unzip the archive to Extract the file : "z4root.1.3.0.apk"
3. Connect your Tab to the PC and initiate "Mass Storage Mode"
Connect USB Cable
Drag down Status Bar and Click "USB Connected" under the ongoing tasks
Click "Turn on USB Storage"
Your device should mount and be available as a Removable Drive in Windows
4. Copy the .apk file from step 2 to your device
It doesn't matter where you put this file. Just remember where so you can find it in the next step(s)
The easiest place would be the "root" of the Removable Disk
5. Enable "Unknown Sources" on your Tab
Settings >> Applications >> Check Unknown Sources Box
6. Enable "USB Debugging" on your Tab
Settings >> Applications >> Development >> Check USB Debugging Box
7. Install Z4Root
Use any "file explorer" program on the Tab. You should have an application called "My Files". It will work fine
Navigate to the .apk file you put on the device in Step 4
Click the .apk file
Click Install
Application will install and you will have a Z4Root Icon in your app drawer
8. Setup Z4Root
Click the Z4Root Icon
You will be presented with two (2) Options. Temporary Root & Permanent Root
I chose Permanent Root but you could "try" it first if you like
In my case the device re-booted and I was rooted.
To test this I installed an application called Titanium Backup (see next Section).
Note: The Z4Root Icon will remain and if you open it again you will be given the option to"Un-Root".
Titanium Backup
Titanium Backup is a GREAT program that lets you backup all your applications as well as the user data that is used by them. For example your game progress, high scores, ETC. Titanium Backup REQUIRES Root access and in my opinion is reason enough to Root your device. There is a Free as well as a Paid version of this application. Let's install this program to verify that we have in fact "rooted" our device.
Installing and Checking for Root
Go to the market and search for Titanium Backup
Give the free version a try just to confrm Root. Simply install it from the market.
Once installed open the application and you should be presented with a dialog box stating that "Titanium Backup is requesting Super User Permissions".
Click allow and follow any on-screen instructions
You will eventually get to an "Overview" screen and should see that Root Access has a Green Checkmark next to it and that BusyBox was installed from the app.
Congratulations you are now rooted
Backing up Files
To backup your applications and user data using Titanium Backup follow the steps below:
Open Titanium Backup and click the Backup/Restore Tab near the top of the screen
A list of the applications installed on your device will appear
Click the Settings Drawer Hardware Key
Click Batch
Under the Backup section on the next screen click Run next to "Backup all User App + System Data"
On the next screen Select the applications you want to backup, They are ALL selected by default.
Make sure the "Pause Active App's" radio button is selected
Click "Run the batch operation" button
Congratulations. You have just performed an application Backup!
Saving your backup to your computer
There is no reason performing a backup if you are just going to leave it on your device. Obviously if something catastrophic were to happen, you would lose the backup as well. The backup files are located in the /sdcard/TitaniumBackup directory.
Initiate "Mass Storage" as outlined in the Rooting Section above.
Once the device is mounted navigate to the TitaniumBackup directory. Note: When mounted to the PC, the /sdcard directoy is the one mounted so TitaniumBackup should appear in the root of the Removable Disk.
Copy the entire TitaniumBackup Directory to your PC
You now have a folder that can be restored to your device allowing you to restore your applications without re-downloading them from the Market.
Remember to copy this folder to your computer after perfoming any future backups.
Restoring your applications
To restore your applications and user data using Titanium Backup make sure that the backup containing the files you wish to restore is located at /sdcard/TitaniumBackup and follow the steps below:
Open Titanium Backup and click the Backup/Restore Tab near the top of the screen
A list of the applications installed on your device will appear
Click the Settings Drawer Hardware Key
Click Batch
Under the Restore section on the next screen click Run next to "Restore missing apps with data"
On the next screen Select the applications you want to Restore, They are ALL selected by default.
Decide if you want to restore just the app, the app and it's data or just the data by clicking the appropriate radio button
Click "Run the batch operation" button
Follow the prompts to install each application
Congratulations. You have just perfored a restore
Note: Once we get into flashing custom Rom's in the sections that follow, sometimes restoring application "data" can be problematic. If you flash a new firmware or Rom and are experiancing issues with an application after restoring it's data, this may be the reason.
Custom Recovery - ClockWorkMod
In the section above we explained about the System Reovery that was built and installed by Samsung. This is great for restoring your system to an out of the box (OOB) condition but not for much else. In order to flash custom Rom's and perform Nandroid Backups we will need to replace the "stock" recovery with a Custom version. ClockWorkMod (CWM) is the recovery of choice for a majority of users and while there are "others" out there, only CWM has been made available for our devices. A Nandroid backup is an exact copy or "image" of your system and can be used to restore your system to the exact state it was in at the time you made the backup. So, lets get to installing CWM.
You will need to download the following file:
Skin1980_P1010_CWM-RECOVERY-BETA-1 ---- MD5 Sum: ca14360ee5f1eebd0efaec5adc77940e
Note: This file is only to be used if you are running the Froyo Version of Android
Using the information above put your device in Download Mode and connect it to ODIN
click the PDA button in ODIN and navigate to the file you just downloaded
Make sure your ODIN screen is setup and matched the screenshot below:
Click the "Start" button and watch your device and the "Message" section of ODIN. You will see some some text in the message center and your screen will show a progress indicator.
Once this completes your device will re-boot. It may boot directly to your new ClockWorkMod OR it might boot back into your operating system.
If it boots to the operating system you can get to CWM using the same procedure outlined in the "Stock" recovery section above. Volume up + Power.
Make sure you are booted into CWM and see the screen shown below:
Once you are in CWM the Volume Up / Down buttonas re used to navigate through the menu choices and the Settings Drawer Hardware ley is used to select an option. The Back hardware key also functions to go back to the previous menu but all screens also offer a "Go Back" choice. If you click the Power Button and are presented with a blank screen simply click it again and CWM will come back up. Now, lets make out first Nandroid Backup!
Making a Nandroid Backup
Navigate and Execute the "Backup and Restore" menu item
Navigate and Execute the "Backup" menu item
Sit back and wait for your backup to complete.
A progress indicator as well as some text will be flashing across the screen
When it completes you will see .. "Backup Complete"
That's it! Congratulations!
Saving your backup to your computer
Again, as with Titanium there is no reason performing a backup if you are just going to leave it on your device. The CWM backup files are located in the /sdcard/clockworkmod/backup directory. Inside this directory you will see a folder that is named based upon the date and time you performed the backup. For Example 2012-02-27.21.57.14 means that the backup was created on February 27, 2012 at 21:57:14. This is UTC time so make sure you add or subtract your UTC offset to get to "local" time.
Initiate "Mass Storage" as outlined in the Rooting Section above.
Once the device is mounted navigate to the clockworkmod/backup directory. Note: When mounted to the PC, the /sdcard directoy is the one mounted so clockworkmod directory should appear in the root of the Removable Disk.
Copy the folder containing your backup to your PC
You now have a folder that can be restored to your device allowing you to restore your system to the exact sate it was in at the time of the backup..
Remember to copy any future backups to your PC as Well.
Restoring a Nandroid Backup
To restore your system to it's nacked up state make sure that the backup containing the Nandroid you wish to restore is located at /sdcard/clockworkmod/backup and follow the steps below:
Boot into CWM
Navigate and Execute the "Backup and Restore" menu item
Navigate and Execute the "Restore" menu item
Sit back and wait for your restore to complete.
A progress indicator as well as some text will be flashing across the screen
When it completes you will see .. "Restore Complete"
Navigate to and execute the "Reboot System Now" menu item
Your device will reboot and you will be restored to the exact state your system was in when you made the backup
Mounting Mass Storage in CWM
In some instances you may be faced with a system that won't boot which makes getting your Nandroid Backup put back on your device problematic. Don't fear. Using CWM you can mount the USB Mass Storage without the need to be running the operating system. Here's how:
Boot into CWM
Plug your USB Cable into your PC
Navigate to and Execute the "Mounts and storage" menu item
Navigate to and Execute the "mount USB storage" menu item
The Device will mount and you will have access to it from your PC
Copy your Nandroid Backup to the clockworkmod/backup folder
Go "back"
Go "Back"
Go to "backup and restore"
Restore your Nandroid
Reboot
Welcome back to a running machine!!
Credit and Thanks
While I have compiled all the files, tested them, generated MD5 Sums and written this tutorial based upon my experiance, it should be noted that other users are responsible for the actual Development. If you think I have done a good job and find this information usefull Please click my "THANKS" button. It is not necessary to thank me by witing a seperate post and by not doing so you keep this thread clean and easy to find the information that others may be looking for You should also visit the following users, find a post or two from them and THANK them as well. Without them none of this would be possible.
Skin1980 for his Development of ClockWorkMod for the GT-P1010
RyanZA for his Development of Z4Root
motafoca for his Development of ClockWorkMod for the KPI Firmware
Donations
While I enjoy tinkering with devices and trying new methods, doing so can be time consuming. Compiling and witing this tutorial took me a considerable amount of time. I have also convieniently placed all the required files on an Ad-Free, Fast Download server so you can get them quick and don't need to hunt around. Mediafire was my server of choice but it is NOT free. I pay a monthly service charge to host on the server and this will also insure that the files are available now AND in the future. If you like my work and feel that it has helped you, I would appreciate a donation as a token of your appreciation. Simply click the button below or the "Donate to Me" button under my Username. Anything you can spare will be appreciated and go toward keeping the file sharing up and running as well as keep me interested in generating more tutorials. Thanks in advance!
Questions or Comments
If you have any questons or feel that certain information could be added or clarified, feel free to post them. I will do my best to check this thread often and assist you as best I can. Valid questions will be answered and added to the Q&A post below.
Firmware and Kernel's for P1010
This section will contain a list and download links for the various Firmware's available for the GT-P1010. As noted above the US version has been getting no love from Samsung with regard to updates. This is a shame and makes no sense to me considering the UK version HAS been actively updated. With this said however many users have been "flashing" the UK versions to their US Tab's with success.
SamMobile Firmware Page
Latest Firmware
Europe Firmware
Middle East Firmware
Compliments of Mod2Xtreme.com
Forum Post Link
Firmware Direct Links
P1010XWKC1_OXX.rar ..... MD5 Sum: 95bd7437271f3bee6eacb017d0ef45a1
P1010XXKPG_P1010XEUKPG_XEU.zip .... MD5 Sum: 3b0f63ccb0b42643d953fcba472eb5f2
P1010XXKPI_XEUKPI_Android_2.3.6.zip .... MD5 Sum: 4d33426db6cecdb48568adecf10bc8fd
Kernel's
P1010ZHKF1-kernel.ZIP .... MD5 Sum: 6dc467ff92fc676c1f61e59e893493eb
Custom Rom's
2/29/2012
Currently there are no Custom Rom's available for the GT-P1010. A Developer named Motafoca is working on a port of Cyanogenmod and information regarding progress can be viewed in the following thread.
Motofoca's Cyanogen Port
Motofoca is a member of the MadTeam and they have their own forum which can be viewed HERE.
The only other "Non-Stock" alternative at this time is CleanRom developed by scrosler There is also a website dedicated to this ROM viewable HERE.
I used the term "Non-Custom" because the CleanRom is based upon a Stock Gingerbread European firmware. From the Website they did the following:
Removed Samsung Bloat!
ADW Launcher or TouchWiz Launcher!
95% AOSP Gingerbread themed
All Apps up to date!
De-Odexed
Zip Aligned
Flashing Stock Firmware(s)
Flashing Stock Firmware(s)
We have said that updated firmware for the US version of the GT-P1010 has NOT been actively provided by Samsung however if you look in Post 2 above you will see that all is not lost. The Europe version of this device has been provided with an update as late as January 2012. I would recommend (and really it was the reason I wrote this tutorial) that you perform ALL the steps above BEFORE flashing any type of Firmawre update/upgrade. This will not only give you experiance running the "tools" but it will allow you to perform the various back-ups in case anything goes "wrong".
Quite simply, Firmware is "flashed" to your device using ODIN. I have searched for a complete guide explaining the vaious sections of ODIN to no avail. Honestly I don't know when certain fields (PIT, CSC), ETC need to be populated and when they don't. I believe, but am not 100% sure that when flashing a brand new Firmware (for example from a US to European version) that the PIT, PDA and CSC fields need to be filled in and the Re-Partition radio button needs to be Checked. I have ALWAYS had the Auto-Reboot & F. Rest Time boxes checked, but again, I can't say why. It is my belief that if the Re-Partition button is checked, that it has the effect of "wiping" all partitions on the device.The only guide I have found is the following:
P1010-Flashingguide.pdf
It is probably a fair statement to make that if a Zip or RAR file you download contains a PIT or CSC file, then you probably need to included them in your flash. Keep in mind that I have experianced an issue where a seperate ZIP file was compressed inside an overall ZIP container. Always make sure that you not only extract the main downloaded file but that you also look inside the extracted folder for another ZIP file that may need to also be extracted.
I will provide an example of my experiance upgrading my US version to the latest UK version below.
Upgrading US Version to Latest Rooted UK Version
First, I must give full Credit to Taney for developing the instructions from This Thread. I followed them and experianced no significant issues. I will be re-creating a portion of them, expanding (clarifying) on some areas that I felt would give NooB's difficulity and then taking the instructions a step farther to upgrade to what is known as the "KPI" version of the Firmware which is the latest one Available. PLEASE make sure that you "Thank" Taney because without the instructions that he provided none of this would be possible.
A. Upgrade / Downgrade to the Latest Froyo Firmware
Place your Device in Download Mode and connect it to ODIN as outlined in the tutorial above.
Download the P1010XWKC1_OXX.rar file from the link in Post 2 of this thread and check the MD5 Sum
Extract this rar file to create a folder called "P1010XWKC1_OXXKC1"
Within ODIN Click the PIT button and navigate to the file "p1wifi_20110128_r10_00.pit" within the folder you extracted.
Click the PDA Button and navigate to the file "P1010XWKC1-REV03-ALL-low-CL946441.tar.md5"
Click the CSC Button and navigate to the file "GT-P1010-MULTI-CSC-OXXKC1.tar.md5"
Make sure the Re-Partition, Auto-Reboot and F. Reset Time buttons are CHECKED
Click "Start". ****** NOTICE THIS WILL WIPE ALL DATA ON YOUR DEVICE*****
When these steps are completed and the process running your ODIN screen should look like this:
When the process Completes your Device will Re-boot. The first Boot could take significantly longer than normal. Just wait and when you see the lock screen open it and enter the OS. At this point you may be experiancing what is known as a "boot-loop". Simply stated the device will keep re-booting and not allow you to do anything without throwing "force close" errors, In his tutorial Taney says that this may or may not happen. It did for me and the fix is in the next section.
B. Flash updated Kernel
To fix the effects of the boot loop you need to flash another file known as a kernel. Like I said I personally DID experiance the boot-loops and had to perform these steps. Since my overall procedure was successful, it is my recomendation that you do it whether you experiance the boot-loop or not. This decision is entirely up to you but you have my suggestion. To flash the Kernel perform the following:
Download the file file "P1010ZHKF1-kernel.ZIP" from the Kernel's section in Post 2 of this thread and check the MD5 Sum
Extract the ZIP file to create the folder "P1010ZHKF1-kernel"
If ODIN is still open replace the file in the PDA field with the file "P1010ZHKF1-KERNEL-eng.tar" from the extracted folder OR
If ODIN was closed open it, repopulate the PIT and CSC fields as outlined in Section A above and select the new file for the PDA field.
UN-CHECK the Re-partition check box
Power off your Tab. NOTE: If it is stuck in a bootloop I found that holding the power button down finally was able to shut off the device.
Start the device in Download mode and connect it to ODIN
If everything is set-up as outlined and ODIN has found your Device.. Press Start
When the process completes your device will re-boot and the ODIN screen will look like this:
At this point you should have a bootable Device and not experiance any further boot-loops. Your About Device Information should read as follows:
Firmware: 2.2.1
Kernel: 2.6.32.9 ([email protected]_24 #1)
Build: Froyo.XXKC1
C. Flash KPG Gingerbread update
In this step we will flash our first Gingerbread update known as the "KPG Version". Follow these steps:
Download the file "P1010XXKPG_P1010XEUKPG_XEU.zip" from the Firmware section in Post 2 and Check the MD5 Sum.
Extract the ZIP file to create the folder "P1010XXKPG_P1010XEUKPG_XEU"
If ODIN is still open replace the file in the PDA field with the file "P1010XXKPG_P1010XEUKPG_HOME.tar.md5" from the extracted folder OR
If ODIN was closed open it, repopulate the PIT and CSC fields as outlined in Section A above and select the new file for the PDA field.
UN-CHECK the Re-partition check box
Power OFF your Tab
Start the device in Download mode and connect it to ODIN
If everything is set-up as outlined and ODIN has found your Device.. Press Start
When the process completes your device will re-boot.
At this point you should have a bootable Device running Gingerbread. Your About Device Information should read as follows:
Firmware: 2.3.6
Kernel: 2.6.35.7 - CL749223 ([email protected] #1)
Build:GINGERBREAD.XXKPG
D. Reinstall ClockWorkMod
The steps above have had the effect of returning your device to stock and therefore the Recovery Partition was overwritten with the "stock" recovery. We need to re-install ClockWorkMod at this point.
Download the following file and check the MD5 Sum
Skin1980-P1010-NEW-CF-ROOT-GB.tar .......MD5 Sum: 1cab6775d572c416371c09f9c3654823
Put your device in Download Mode and Connect it to ODIN
Navigate to the File you downloaded using the PDA field
Leave the PIT and CSC fields BLANK and Un-Checked
Un-Check the Re-Partition Check Box
Click RUN
When the operation completes the device will re-boot
At this point you will have a Rooted KPG Version of Gingerbread with a fully Functioning ClockWorkMod Recovery. You may wish to stop here but reports informed me that the KPI firmware was faster. I decided to Install it as outlined blelow/
E. Flash KPI Gingerbread update
Before Installing the KPI Update I did the following:
From within the running system went to CWM application and opened it.
Granted the application Superuser Permissions
Used the application to "Re-Boot to Recovery"
Device Re-Booted into CWM and I performed a Nandroid Backup
While still in CWM "Wipe Data / Factory Reset" AND
Wipe Cache Partition AND
Wipe Dalvik Cache
Power Off
Your Device is now ready to recieve the KPI Firmware Update
Download the file "P1010XXKPI_XEUKPI_Android_2.3.6.zip" from Post 2 and Check the MD5 Sum
Extract the the file to create the folder "P1010XXKPI_XEUKPI_Android_2.3.6"
Start you Device in Download Mode and connect it to ODIN
Navigate to the file "P1010XXKPI_P1010XEUKPI_HOME.tar.md5" in the PDA Field
Leave the PIT and CSC fields Blank and Un-cjecked
Make sure the Re-Partition checkbox is Un-Checked
Click Run
While the program is running your ODIN screen will look like this:
When the Process completes your Device will Re-Boot and your About Device Info will be as follows:
Firmware: 2.3.6
Kernel: 2.6.35.7-CL882382 ([email protected] #1)
Build: GINGERBREAD.XXKPI
At this point I performed the following:
Went Through Initial Setup Screens
Powered Off Device
F. Re-Install ClockWorkMod AGAIN
Same as before. The procedure has wiped out our Recovery and we need to Re-install it. This time however we will use a different file beause I do not Believe the Skin1980 Gingerbread Version is compatible with the KPI Firmware. Luckily we have another Developer working on this Device. Please visit and Thank Motafoca for providing the following file:
madteam-cwm-p1010-kpi.tar .......MD5 Sum: f868e789245ec3dae87efaf2e30b1165
Put your device in Download Mode and Connect it to ODIN
Navigate to the File you downloaded using the PDA field
Leave the PIT and CSC fields BLANK and Un-Checked
Un-Check the Re-Partition Check Box
Click RUN
When the operation completes the device will re-boot
At this point you will have a Rooted KPI Version of Gingerbread with a fully Functioning ClockWorkMod Recovery.
G. Final Steps (Optional)
Opened CWM Application and Granted SuperUser Permissions
Rebooted to Recovery Using "Reboot Recovery"
NOTE: This version of CWM uses different button mappings. Volume Up / Volume Down to navigate and POWER button to Select
Mounted Device using Mounts / Storage and connected to PC
Put Titanium Backup files back on Device
Reboot System Now
Setup Date and Time
Connected to WiFi
Went to Market and Added Google Account
Waited for Account Sync to complete
Re-Enabled "Unkonon Sources"
Downloaded and Installed Titanium Backup
Ran Titanium Backup and Restored app's and data
DONE and running PERFECT !!!! Enjoy!!!
Donations
While I enjoy tinkering with devices and trying new methods, doing so can be time consuming. Compiling and witing this tutorial took me a considerable amount of time. I have also convieniently placed all the required files on an Ad-Free, Fast Download server so you can get them quick and don't need to hunt around. Mediafire was my server of choice but it is NOT free. I pay a monthly service charge to host on the server and this will also insure that the files are available now AND in the future. If you like my work and feel that it has helped you, I would appreciate a donation as a token of your appreciation. Simply click the button below or the "Donate to Me" button under my Username. Anything you can spare will be appreciated and go toward keeping the file sharing up and running as well as keep me interested in generating more tutorials. Thanks in advance!
Thread Consolidation and Links
The following Threads have been found and pertain strictly to the GT-P1010. If you find another thread that you feel should be included either link it in a post or PM me. I will review same and add to this section as appropriate.
[WIFI Only] [How-to] GT-P1010 Gingerbread Update ........ Thanks Taney
[CWM][RELEASE] Clockworkmod recovery for P1010 ....... Thanks Skin1980
Galaxy Tab p1010 tweaks ..... Thanks s2h2golf
[Tool / Mod] - CleanMOD 1.0.1 for GT-P1010 Gingerbread 2.3.6! Mod the Tab! ..... Thanks scrosler
Omg. G-R-E-A-T thread. Soo cool. Well, maybe we can cm on the tab, but a lot of developers are selfish
thank you for creating this guide!!
I got one of these for my daughter to play with and I was having a hard time figuring out what information pertains to her model.
Question and Answer Section
***** Reserved for Questions and Answers *********
2013-03-09 - I have been away from these forums for awhile now and apologize if I haven't been around to answer any questions. Just been too busy with other responsibilities. While I still own this device, I have moved on to another and have not kept up with development on the GTP-1010. I hope that many users have had success but I know from reading the posts that a few have struggled. Thank you to those that have attempted to assist in my absence. Honestly, without doing much with this device, I don't know how to answer some of the PM's I have received. This device was at the time considered "Legacy" in my mind and over 1 year later I don't believe anything has changed. With this said I will not be providing additional information or files and it does not make financial sense for me to continue paying for the "Pro" mediafire account. I will be canceling it today but have paid for it through 2013-04-01 at which time it will revert to a "free" account. I have no idea at this time what will happen to the links in my posts on that date but suggest that anyone interested, download everything before then. If time permits I will attempt to move everything over to a new server but I make no promises. The "free" version of Mediafire may still work but I vaguely remember paying for "pro" for a reason. I just don't remember why. Thanks for all the "thanks". I'm glad this has at least helped some people. Again, I appologize for not being around and for any issues with the links after April, 1 2013
******* One More for Good Measure ********
Bravo
Thank you for your hard work. Sent donation. Saved me hours of searching and coordinating the info. C'mon guys, how much time has this post saved you?
Hi i followed your instructions until i got to "Rooting" section.. the little problem issue i have is that the device i have doesn't have the Android Market..(i know i was shocked too) it has the Samsung Apps online but even that doesn't have the Titanium Backup App... any suggestions of how to install the Android Market? (btw love the instructions, nice and clear)
apolonetics said:
Hi i followed your instructions until i got to "Rooting" section.. the little problem issue i have is that the device i have doesn't have the Android Market..(i know i was shocked too) it has the Samsung Apps online but even that doesn't have the Titanium Backup App... any suggestions of how to install the Android Market? (btw love the instructions, nice and clear)
Click to expand...
Click to collapse
Sorry about the late response. Honestly this forum gets very little attention and I haven't been checking as often as I should.
That said ... I think you need to review post 4 which is an extension of the lessons learned in post 1. The firmware files ALL have the market built into them and following those steps should return you to a STOCK ROM. Make sure you backup any user files that you need before you begin. An internet search should allow you to find the .apk file for titanium backup. If you enable "unknown sources" in settings and get the app onto your device, clicking it should install the application. I'm not sure though if you finished the rooting step of stopped short or it. You NEED root to run Titanium,
Also, Keep in mind that as stated I performed these steps on a US version of the hardware and I don't offer that devices from other regions will be 100% compatible. But, from my research I believe most should be.
In summary, please provide me with additional details regarding your device and it's history. I'm sure we can get you squared away. There is always a Google App's package (GAPPS) that could be flashed to your device to get the Market but I am concerned about the fact that your's doesn't have it. This makes me think that without starting from a fresh ROM we would ultimately just be chasing our tails trying to troubleshoot other issues.
Thank you so much for replying.. i didn't think you'll reply to my post... but before i go to the next step.. i was playing around with it.. following your instructions on updating drivers and rooting etc... i then got stuck on "rooting" section hence me posting for help on getting the Titanium Backup... anyway i decided to upload couple of rugby videos so i can watch it later... i was in the middle of one video when all of sudden it stopped and turned itself off, i turned it back on and it stuck on the Samsung logo and it has been stuck on that since 24+ hrs ago after turning it on/off... on/off - i think i might have f'd it up...
I got it as a prize from a competition last year (2011) in Oct, and ever since i've been having problems with it.. let me know what other info you need me to provide!
much appreciated for the help!
THANKS SO MUCH! You made my day!
-Redbearded Tyrant
"Sic Semper Tyrannus"
apolonetics said:
Thank you so much for replying.. i didn't think you'll reply to my post... but before i go to the next step.. i was playing around with it.. following your instructions on updating drivers and rooting etc... i then got stuck on "rooting" section hence me posting for help on getting the Titanium Backup... anyway i decided to upload couple of rugby videos so i can watch it later... i was in the middle of one video when all of sudden it stopped and turned itself off, i turned it back on and it stuck on the Samsung logo and it has been stuck on that since 24+ hrs ago after turning it on/off... on/off - i think i might have f'd it up...
I got it as a prize from a competition last year (2011) in Oct, and ever since i've been having problems with it.. let me know what other info you need me to provide!
much appreciated for the help!
Click to expand...
Click to collapse
Honestly in order to support you I believe you should start from scratch. You should be able to get the device to download mode even if it is stuck on the Samsung Logo. Hold the power button until the unit turns off completely and then use the instructions to enter download mode. Then follow all the instructions in Post 4.
This will of course wipe your device totally clean so make sure you have everything backed up. Even though you can't get the system to boot you may be able to access your files by hooking it up to the PC. This is certainly true if you have already installed CWM. Look in the tutorial and find the section where I discuss "Mounts & Storage" from within CWM. This will allow you to copy off any important files. Then perform all the steps in Post 4.
That is really all I can offer as I don't know what you have done on the device to this point.
hai there.
i have few questions regarding upgrade to gingerbread.
my OS is 2.2.1 Froyo.DXKG1
if i want to upgrade my device to gingerbread P1010XXKPI_XEUKPI_Android_2.3.6, should i upgrade my device to the latest froyo (P1010XWKC1_OXX) then to gingerbread (P1010XXKPG_P1010XEUKPG_XEU) then to gingerbread (gingerbread P1010XXKPI_XEUKPI)??
or i can upgrade it straight away to gingerbread P1010XXKPI_XEUKPI_Android_2.3.6??
Thank you
Hi, i can't find your Post 4, are you able to post a link here please... ta
totihut said:
hai there.
i have few questions regarding upgrade to gingerbread.
my OS is 2.2.1 Froyo.DXKG1
if i want to upgrade my device to gingerbread P1010XXKPI_XEUKPI_Android_2.3.6, should i upgrade my device to the latest froyo (P1010XWKC1_OXX) then to gingerbread (P1010XXKPG_P1010XEUKPG_XEU) then to gingerbread (gingerbread P1010XXKPI_XEUKPI)??
or i can upgrade it straight away to gingerbread P1010XXKPI_XEUKPI_Android_2.3.6??
Thank you
Click to expand...
Click to collapse
Yes! This is what worked 100% for me so I recomend all the steps. The first upgrade to latest froyo has repartition checked which essentially gives you a clean slate. The seperate GB steps insure you end up with root. Good luck!
apolonetics said:
Hi, i can't find your Post 4, are you able to post a link here please... ta
Click to expand...
Click to collapse
Its the 4th post in THIS thread. "Flashing Fimware" section.

For the complete noobs

I have been working on changing the Operating system on my A500 for the past 3 days. I'm retired and it really has been three 12 hour days. The forum has been a font of information but it is scattered and confusing to someone new like me. I have been writing what I did and wanted to share it with the other noobs. Of course I had to register on the forum first. So today is my first day registered and here is my first post.
A procedure for changing the ROM in an A500
This procedure is for Windows. It can be done on Mac and Linux but we're not going there. It uses Afterota v1.09 by gersma. Although the program is great, there is really no explanation of how it works or how to use it. I hope this procedure helps the noobs like me.
You can install Honeycomb (HC), Ice Cream Sandwich (ICS) or Jelly Bean (JB). I'm not giving links because they change, are unavailable or otherwise wrong. Plus this is written to be printed and followed on paper because there is a PC restart involved; also I sometimes lose my place while online. If you can keep it straight, more power to you. I'm writing this for complete noobs. Admit it, we were not born knowing this stuff. As a complete noob I am also assuming you and I have not changed our A500 in any way other than the normal updates from Acer and Google.
Now for the disclaimer:
You do this at your own risk. If you point a finger at me and start yelling, I will hold up a mirror facing you so you can see who is to blame.
Prep your A500 for the procedure
For safety sake, remove the micro SD card if you have one installed.
Plug the A500 in to AC power, power it ON and ensure it is fully charged. Keep the tablet powered from AC. Ensuring it is fully charged is insurance against accidental power loss. You don't want to loose power while doing this procedure or your tablet could become a paperweight. Place the tablet close to the PC (notebook or desktop) you will be using for the procedure. You're going to connect the tablet and PC together with a USB cable later. The best cable is the one that came with the A500, the one with the micro USB end and regular USB at the other. If you use something different, make sure it is a good quality cable.
The next step is to set the tablet to accept changes. Tap Apps → Settings → Developer options → USB Debugging.
If your tablet is password protected, disable it now. You'll have to set it up again anyway after the change.
Prep your PC for the procedure
Download and install the USB drivers for the A500 from acer.com.
Go to the xda-developers.com forum and download Afterota. You can search for the program. It doesn't require installation, it just runs as is.
Another thing to look up is recovery apps. There are a number of them and they all do the same thing in slightly different ways. Afterota v1.09 offers four, Thor 1.7.3 (touch screen), TWRP 2.1.3-ICS (touch screen), Ra v3.1.7 (touch screen) and Pub v0.2 (Vol and power button). I discuss recovery later.
Next we need a ROM to load. Again, go to xda-developers.com and search for one that interests you. They are under the Iconia A500 Development section. When this was written, I installed JB 4.1.2. I highly suggest you read up on the ROM you want. Check for status, useability, included apps, excluded apps, bootloader requirement (for this procedure ICS), etc. When you finally download your preferred ROM, do not extract it. You will be using it in the zipped form.
I have seen a zip file called gapps (Google apps) on xda-developers.com. It appears to be needed for some ROMs. Again, download it if necessary but do not unzip it. The JB ROM I used specifically stated the gapps were included.
The next step is to disable User Account Control (UAC) in Windows. Go to Control Panel → User Accounts → Change User Account Control settings and drag the slider to the bottom. You will have to restart the PC for changes to take effect.
The procedure
Install bootloader and recovery
It looks like you're ready to proceed.
Connect the PC and tablet together with the USB cable. Place the small end into the tablet and the larger end in a PC USB port. You will see the device drivers load and Windows Explorer will ask what to do. Click on Open device to view files.
At this time, you can browse the tablet using Windows Explorer. Most everything you want to see is on the Internal storage partition. If you have a micro SD card inserted, it will show as SD card. I strongly suggest you check through the folders for any data, documents, music, videos, etc that you may want to safeguard. Copy the folders and/or files to the PC. If they get destroyed on the tablet, you can copy them back later.
Run Afterota. The first thing Afterota does is collect information from your A500. It takes a few moments so be patient. When done, it will save the text file, AcerIDs, to your desktop. This file is very important. It will have the tablet's serial number, CPUID, SBK and other stuff. It is a very good idea to save it and/or print it for future use; it could get overwritten later.
There are five tabs in the Afterota window. Info – where we just collected the information, Stock – to go back to HC, Standard – where we will be going next, Advanced – unbrick and other stuff and About.
In Standard we need to choose a bootloader.
What exactly is a bootloader and why do we need it? A bootloader is akin to the starter of a vehicle. You insert your key into the ignition and turn it to start the engine. A bootloader starts the operating system (engine) of your tablet. If you change the engine in your vehicle, you need to install a compatible starter. We are going to be changing the engine of your tablet, so we need a new starter as well.
Afterota v1.09 has 2 bootloaders. One is just for HC. The other one is for ICS and presumably for JB. Make sure your ROM will use an ICS bootloader. You'll notice the Bootloader ICS options have the same bootloader version but different recovery apps.
Recovery here is and isn't the same thing as in Windows. From the factory, you use the Acer Recovery app to get your A500 back to original factory setup like in Windows. You use one of these Afterota recoveries to install a new operating system (OS). The differences in the Afterota recovery apps is the way they present options. The only one I've used is Twrp v2.1.3. It has a nice GUI. You should have read up on them all and decided for yourself which to use.
Click on the A50x box for the recovery you want and the program will do the install.
Once the program is done it will reread the tablet and generate a new AcerIDs file. Keep the original file, for some reason the second one doesn't get the tablet serial number. Of course, you can keep both. You can close Afterota now.
Install ROM
The next step is to copy your zipped ROM to the Internal storage of the A500 tablet. Do not put it in the SD card. You can also put the gapps zip file here now if you need it.
Disconnect the USB cable and power OFF the tablet.
Press and hold Volume down side of the Volume button (the side closest to the power button) while pressing power on. Wait til you see the booting recovery image message then release the buttons. You are now in the recovery app you chose earlier.
The words and menus may differ between recovery apps but the functions are the same. You will probably have to move between menus. Just take your time and think about what you are doing and you should be fine.
Wipe, Erase or Delete caches and do a Factory Reset. Next, format the system and flexrom.
Now, traverse to where you see the menu option Install Zip from SD (or something to that effect). Choose your ROM and install it. If you put the zipped gapps on the tablet, you can install that as well. If not, you can do that later.
Once successful, boot up normally to your new OS. The first boot takes a very long time. Be patient.
Time for thanks. Thanks to gersma for Afterota. Thanks to all the developers of the booloaders, recoveries and ROMs. Especially thanks for sharing your work.

[Guide] Step by Step from Stock N910V 6.0.1 to hsbadr's CyanogenMod 13.0

Code:
/*
*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*
*/
IMPORTANT: Read the ENTIRE instructions set before starting, make sure you know what you are getting into. I have been as straight forward as possible with my instructions to assist noobs with the procedure.
Mission Statement
The purpose of this post is to combine the following 4 guides, in an easy to read manner to help people get from a stock Note 4 Version running 6.0.1 to a fully rooted Note 4 running CM13.0
Guides Referenced and Summarized:
[Guide] A noob's guide to Perm Root & TWRP on Verizon Note 4 Retail 5.1.1 (BPA1) http://forum.xda-developers.com/note-4-verizon/general/guide-noobs-guide-to-perm-root-twrp-t3360883
[HOWTO] Bootloader Unlock and Upgrade to Marshmallow [N910V] http://forum.xda-developers.com/not...t/howto-bootloader-unlock-upgrade-to-t3398144
(no title, sub post #1403, describes going from CPD1 to Jasmine with CPF3 and Firmware/Kernel Patch) http://forum.xda-developers.com/showpost.php?p=67481370&postcount=1403
[ROM] [6.0.1] [UNOFFICIAL] CyanogenMod 13.0 [Jul 24, 2016] http://forum.xda-developers.com/note-4-verizon/development/cyanogenmod-t3253973
I will use large chunks from some of these guides, skip some parts not necessary and/or extrapolate/modify on the instructions given within.
Thankx & Achnologments
Main Contributors (I plagiarized, quoted, or sourced)
Robots_Never_Die
hsbadr
Tech Support
BickNasty
Feel like I missed you, it wasn't intentional....PM me and I'll consider adding you, if I feel you actually contributed in some way or I copied your work.
Satisfied Customers (Did my method work for you? Post a reply and let us know, I'll add you to the list)
jwp1299 - 1 hour
Viper-Link
keviinese - 1.5 hours
pfcland - 1.5 hours
Required Apps (Google Play) All Free
Search for and install these apps
eMMC Brickbug Check (free)
Required Downloads (note on version numbers: version numbers I specify are ones available at the time I wrote this guide. For most tool grab the newest version, such as Odin/ADB)
NOTICE Total size of Downloads is approximately 7 GB, some of the links may be slow! Time required may vary due to your network speeds, and luck with speeds from file hosts. (expect several hours)
ADB – minimal_adb_fastboot_v1.4.0_setup.exe
Odin - newest version (3.12.3 at time of writing)
Kingroot - Grab latest stable version, only grab NewKingroot(XXXXX).apk
Samsung USB drivers (windows) - newest version
Bootloader Unlock - samsung_unlock_n4-fix
TWRP - twrp-3.0.2-0-trltevzw.tar.md5
N910VVRU2BPA1_N910VVZW2BPA1_VZW.tar.md5
N910VVRU2BPA1_N910VVRU2CPD1_FullFirmware.tar.md5 (Alternate Torrent if slow: Torrent started by pfcland)
JasmineROM_v7.0_N910VVRU2CPF3.7z
N910VVRU2CPF3_PartialFirmware_PatechedKernel.tar.m d5.7z
Gapps For ARM SDK23 (Android 6.0) (mini version is recommended)
UNOFFICIAL CyanogenMod 13.0 Builds for Verizon Samsung Galaxy Note 4 (SM-N910V) (grab newest from top)
Xposed framework for ARM SDK 23 (NOTE: Grab both the xposed23.zip and XposedInstaller****.apk)
XPosed is OPTIONAL, but there are a lot of rooted apps that use the XPosed framework to get more control over your phone. Such as hiding mock locations for example.
NOTE: Internet is REQUIRED for KingRoot to function (grants temporary root, so ADP commands can be executed to unlock bootloader), at one point WiFi will NOT function but internet is still required. So a valid SIM with internet is required (Verizon will definitely work, others might[/] work)
NOTE: The entire installation will take an estimated 1-2 hours. (Not including time spent downloading) All steps are MANDATORY, do not SKIP anything....You've been warned
Install eMMC Brickbug Check (free) on your phone, and RUN IT. Your CID MUST start with 15. If it doesn't I can't help you, and this guide is not for you.
Install the Samsung USB drivers on your windows PC
Backup your phone, if you don't know how.....google it...And learn how, you will want to backup frequently. Every time you get to a point you can boot up into Android, backup...it's safer for you...I will not remind you again, this is on your head.
Disable Encryption on your phone, both the SD card and Device
Disable Samsung Phone Lockout. YOU MUST DO THIS OR ELSE!!!! (Settings > Security > Reactivation Lock)
Do 2 factory resets on your phone, one after another (hold volume up, home button, power when starting to enter recovery mode where you can reset phone). Not required but if you don't, you'll spend an extra hour or two doing this because Kingroot will crash/fail more often.
Boot up your phone in Download Mode (hold volume down, home button, power)
Open Odin3, Click the AP button and select the file N910VVRU2BPA1_N910VVZW2BPA1_VZW.tar.md5, once it checks it, goto options and make sure the Re-Partition is NOT selected. Now click start to flash and downgrade to Android 5.1.1.
Turn on your phone, and let it boot up.
Skip everything possible when setting up your phone. Don't even put in a google account, not necessary
Goto Setings and set the following
Settings > Security > Reactivation Lock = Disabled (EXTREMELY IMPORTANT, VERIFY)
Settings > Security > Unkown Sources = Enabled
Settings > Developer Options > USB debugging = Enabled
Developer options are unlocked by going to Settings > About Phone. Find "Build Number", and start clicking it till you get a message that Developer Options have been unlocked (about 10 clicks I believe, never counted).
Settings > Developer Options > Verify App via USB = Enabled (should be by default, CHECK)
Settings > Lock Screen = None
Settings > Display > Turn off Display = 10 Minutes
Plug your phone into your computer via USB, copy the NewKingroot****.apk to your download directory (samsung-sm-N910V\Phone\Download)
Install ADB onto your Windows PC. Select an easy directory such as c:\ADB
Copy the following file directly into the ADB directory
samsung_unlock_n4-fix
Open up command line interface. Hold windows key & press R key for run, type in "cmd" press enter. Will open a terminal window for you. Type the following commands:
cd\
cd adb (or whatever you named your directory where you installed ADB)
adb devices
This should return a list of devices you have connected, something like:
Code:
List of devices attached
SerialNum device
If no devices are displayed, check you have the Samsung USB drivers installed properly.
Type the following command
adb push samsung_unlock_n4-fix /data/local/tmp/
Got an error? check your spelling (or copy/paste from me), check you put the file into the ADB directory (not just a link), your phone must be on and screen not locked and check you have usb debugging enabled.
BTW: Do NOT CLOSE the window unless I instruct you to!
Install Kingroot on your phone, which you previously moved into your downloads folder, you can find it via My Files app that comes with phone.
Now run KingRoot. Flip down to the bottom and click "Try It", it will run some quick test then give you a button to try to root your phone.
Wait...Wait...Do not worry if your phone restarts, it will go back into KingRoot automatically on reboot. Just sit back and wait, it may fail multiple times and you may have to re-run Kingroot. Just keep trying . Once it succeeds you must do the following IMMEDIATELY AND AS FAST AS POSSIBLE. Kingroot is HIGHLY UNSTABLE.
On the windows PC, back in the command window you left open. Start Typing.
adb shell
su
cd /data/local/tmp/
chmod 777 samsung_unlock_n4-fix
chown root.root samsung_unlock_n4-fix
./samsung_unlock_n4-fix
After the last command it may prompt you to type yes, do so immediately. it won't write on the screen but type yes anyway for it to continue. Once it's done it should automatically start to reboot your phone. Unplug it and pull the battery, wait 5 seconds, put battery back in and plug the phone back in.
This was the initial setup for unlocking your bootloader, you now have to run it AGAIN so turn your phone back on. Repeat steps 22-24, after the 2nd time PULL OUT YOUR SD CARD BEFORE TURNING ON YOUR PHONE
Congratulations you now have an unlocked bootloader, you can close the command window on your PC.
The SD card has a restore point for your phone prior to removing your bootlock. Save it if you want, or plug into your phone and format the 18mb partition you are able to. You must format it on a PC before you can use it again in a phone!!!! Will shut your phone off immediately if you put the SD in without formatting that 18mb partition.
Now reboot your phone into download mode (hold volume down, home and power buttons when turning on)
Open Odin App on your PC, Click the "AP" button and select the file twrp-3.0.2-0-trltevzw.tar.md5 (which you downloaded earlier). Once it does it's check, verify that re-partition is NOT selected in options. Now click start to flash twrp bootloader.
Your phone will restart, re-enter download mode. If you missed it pull cable/battery and try again.
Now extract and flash N910VVRU2BPA1_N910VVRU2CPD1_FullFirmware.tar.md5 via Odin, same as you did with twrp. VERIFY THAT RE-PARTITION IS NOT SELECTED IN OPTIONS.
Boot up in recovery mode (hold volume up, home and power when turning on) (note: no longer TWRP since you flashed firmware, will look different again)
"Wipe data/factory reset ", then reboot your phone.
Now repeat steps 9-12 (NewKingRoot should still be in your downloads, but verify anyway) (NOTICE: wifi will NOT work with the CPD1 firmware, but Verizon internet should in case you need internet for some reason, wifi will restore later in guide - Other internet from other providers MIGHT work with proper APN settings)
Install a clean SD card into the phone.
Now repeat steps 15-25. This time you should only need to run the samsung_unlock_n4-fix file once to break your boot. This is what it typically says on successful bootloader unlock: (if you got this message, pull the battery, cable and SD card.)
Code:
[email protected]:/ # cd /data/local/tmp/
[email protected]:/ # chmod 777 samsung_unlock_n4-fix <
[email protected]:/ # ./samsung_unlock_n4-fix
============================== samdunk unlock 0.0.1 ==============================
NOTE 3 BETA UNLOCK!!!!!!!!!!!!!
this application comes with NO WARRANTY (express or implied)
this binary may not be rehosted, repackaged, one-clicked, etc.
there is no support provided for this application
this application has been tested on the Verizon Galaxy S5 only
it may work on the AT&T Galaxy S5, and possibly other similar Galaxy devices
there are no compatibility checks, do your research first
if run on an incompatible phone, it will likely permanently ruin the device
we STRONGLY advise against running any binary not obtained from the official source
official source is available at http://github.com/beaups/SamsungCID
SD card is required, all data on the SD card will be destroyed
changing to this developer CID may have other implications
the psn derived from the CID may be used for critical services
changing this psn may cause unexpected behavior or loss of services
continue at your own risk, you've been warned
aboot dev signature research credit to ryanbg
http://forum.xda-developers.com/member.php?u=766721
eMMC vulnerability, exploit, and the code you are running by beaups (sean beaupre)
http://forum.xda-developers.com/member.php?u=711482
Do you understand the implications of these warnings?
(Yes/No)
[+] CID at boot time is/was: 150100523231384d4100657e54fc1200
[+] dev CID matching, proceeding to unlock
[+] backing up loaders, this will take a few minutes
[+] loaders successfully backed up
[+] success! powering off device, hopefully its not bricked!
Now boot back into download mode
Flash TWRP via Odin again (I'm summarizing greatly now, as you should by now understand this kind of shorthand)
Ok, now boot up into TWRP recovery mode (vol up, home, power)
Navigate through TWRP menus to create a Backup. Click Backup Button, and swipe to create backup. (this is just so that it creates the directory structure on your phone)
Click the Reboot System button, skip all the setup you can again. (DO NOT INSTALL SUPERSU!!! will cause bootloop)
Extract the "JasmineROM_v7.0_N910VVRU2CPF3.7z" file it will create a directory called "JasmineROM_v7.0_N910VVRU2CPF3".
Plug USB into phone and to computer. Copy the JasmineROM_v7.0_N910VVRU2CPF3 folder into \Internal storage\TWRP\BACKUPS\Phone SN\
Reboot into TWRP recovery
Click the Restore button (DONT start the restore yet!!!), and check that your JasmineROM is listed as a recovery option. (don't recover YET) If it's not there you copied it into the wrong directy, try again before proceeding.
Go back to the main menu, Click the Wipe button. Click the 'Advanced Wipe' button, and wipe the following cache/dalvik/system/data
Go back to Restore (from 2 steps ago) and run the JasmineROM_v7.0_N910VVRU2CPF3 recovery, return to main menu afterwards
Go to wipe, and wipe the cache/dalvik only this time.
Reboot into download mode
Flash the N910VVRU2CPF3_PartialFirmware_PatechedKernel.tar.m d5.7z file via Odin
Reboot the system, this will take a LONG TIME. WAIT for it. (if reboot takes >10 min, pull battery and restart)
Once it boots up, skip all the setup again. Copy the CM13, Gapps and XPosed (both zip and apk) to your downloads. Don't unzip anything, not necessary.
Now reboot into recovery go to WIPE and do a factory reset by swiping.
Then goto Install (still in recovery) and install CM13, then Install Gapps.
Reboot your phone, this time you are setting up properly reboot will take a while to optimize your apps depending on Gapps version used. So do all your setup as you want your phone setup. Once that's done, restart the phone in recovery. (if reboot takes > 5 min, pull battery and restart)
Install via TWRP the XPossed.zip file.
Reboot your phone, once on. Navigate via My Files, to downloads and install XPosed.apk
CONGRATULATIONS. You now have a fully Unlocked, Rooted Note 4 Verizon with CryanogenMod 13.0 installed and XPosed Installed.
Suggested Apps
Kernel Auditor [ROOT], will allow you to adjust kernel settings. Such as CPU clock speeds and thermal throttling, if your phone is too hot.
Note: About ROOT[/], you will have root once you finish this guide. But it is disabled by default, you can enable root in developer options (no reboot required when changing). Unlock your developer options again, and scroll down you will see an option to enable/disable root. This allows you to keep turn off during normal use, and only enable it when you need to install an app that requires root. You can always just leave it on all the time, that is your choice.
Note: Some apps on Google PlayStore will become unavailable due to incompatibility (according to google, HA). Such as YouTube Music, you will no longer be able to install it through the store. But you can install it by using an APK site, such as APK Downloader. On this site you find the app you want on play.google.com, copy the HTTP link and put it into the APK Downloader and it will generate a direct download link to the APK file. Copy onto your phone and sideload (ie. install) through file explorer. I don't endorse them, they are just one of many places you can get APK files.
Change Log
7/28/2016
Another success story :good:
Added note about how root works in CM 13.0
Corrected Step 34
Minor text adjustments, for clarification
Made note that wifi doesn't work with CDP1 flash
Added note that you MUST HAVE a valid sim card with internet access for step 35! KingRoot requires internet to function, and Wifi will NOT WORK after flashing CPD1 firmware (incomparable drivers).
Added another note about internet at the top of the instructions, to make sure people are aware.
7/27/2016
Added Bicknasty to the Contributors list - helped resolve issues I had with CM 13.0 kernel & modem.
Added a note to downloads section regarding total size of files downloaded and expected time.
Re-wrote steps 40-48 to make it easier to understand. Adding some steps and explaining in more detail.
Added note at the top to read ALL the instructions once before starting
Added note with the estimated time to perform all the steps
Added note suggesting Kernel Auditor app, and made reference to the fact that some apps on playstore will NOT install from playstore. Suggested APK Downloader for apps not available from store
Added a Success Story Section
Added note on how to enable developer options
Any faster source for N910VVRU2BPA1_N910VVRU2CPD1_FullFirmware.tar.md5
jwp1299 said:
Any faster source for N910VVRU2BPA1_N910VVRU2CPD1_FullFirmware.tar.md5
Click to expand...
Click to collapse
Probably, but that's the only one I know which is a free download that I'd trust.
JacekRing said:
Probably, but that's the only one I know which is a free download that I'd trust.
Click to expand...
Click to collapse
Alright, still works just a little long. Thanks so much for the guide, working great so far!
jwp1299 said:
Alright, still works just a little long. Thanks so much for the guide, working great so far!
Click to expand...
Click to collapse
How far are you now?
And let me know when you finish, critique my guide. If parts weren't clear enough let me know.
And finally if you run into any issues let me know.
Great guide (I honestly haven't read it, it's too long but it looks thorough, and I know you were annoyed with the tedious process), glad I was able to help you figure things out!
Bicknasty said:
Great guide (I honestly haven't read it, it's too long but it looks thorough, and I know you were annoyed with the tedious process), glad I was able to help you figure things out!
Click to expand...
Click to collapse
Yea I do appreciate the help Bicknasty. I'll add you to contributors list later as helping with cyanogen issues I was having.
Bicknasty said:
Great guide (I honestly haven't read it, it's too long but it looks thorough, and I know you were annoyed with the tedious process), glad I was able to help you figure things out!
Click to expand...
Click to collapse
You know it wasn't so much that it annoyed me it's that there was no concrete guide telling me what to do. It's a thread here, a post there to do a specific thing but they aren't coordinated in a logical way for users to easily find.
Alright ignore what I said before this edit, I just skipped a step.
I must say though, steps 41-43 are very confusing. What is the ROM folder?
jwp1299 said:
Alright ignore what I said before this edit, I just skipped a step.
I must say though, steps 41-43 are very confusing. What is the ROM folder?
Click to expand...
Click to collapse
The ROM folder I'm referring too is the folder inside the Jasmine zip file. I only reference it so people wouldn't try to take just the files inside the folder which is inside the zip file. Lol yea that's confusing....I'll think about how to rewrite those and make adjustments in a couple hours to make it clearer.
But basically when you extract the Jasmine zip file it creates a folder with files in it. Copy the whole folder not just the files to where it makes your recovery folders.
JacekRing said:
The ROM folder I'm referring too is the folder inside the Jasmine zip file. I only reference it so people wouldn't try to take just the files inside the folder which is inside the zip file. Lol yea that's confusing....I'll think about how to rewrite those and make adjustments in a couple hours to make it clearer.
But basically when you extract the Jasmine zip file it creates a folder with files in it. Copy the whole folder not just the files to where it makes your recovery folders.
Click to expand...
Click to collapse
Okay, awesome. Also I think the TWRP part could be explained a little clearer.
Other than that, 100%
oh also, at the start I would say to read the entire thing before starting, and give a warning that downloads will take like 4 hrs
jwp1299 said:
Okay, awesome. Also I think the TWRP part could be explained a little clearer.
Other than that, 100%
oh also, at the start I would say to read the entire thing before starting, and give a warning that downloads will take like 4 hrs
Click to expand...
Click to collapse
Lol yea, didn't think to mention reading the whole thing first. To me that's a given I always read everything before starting. I'll add a note to read everything.
As to download time, well it is like what 12 gigs in total? Basically 4 full versions of the Android OS at 2 gigs reach plus all the extras.
I'll try to see if I can't explain the twrp recovery of Jasmine better. Only reason you need to do Jasmine is for the 6.0.1 device drivers (such as modem).
jwp1299 said:
Okay, awesome. Also I think the TWRP part could be explained a little clearer.
Other than that, 100%
oh also, at the start I would say to read the entire thing before starting, and give a warning that downloads will take like 4 hrs
Click to expand...
Click to collapse
I've modified the guide appropriately, to resolve all of the issues (I think) you mentioned. And to make some steps easier to understand and follow.
I also added a recommended app on the bottom, and mentioned a site you can use to get PlayStore apps which will now list as incompatible with our phones.
Finally, question: Did you succeed using this Guide? Just curious if everything is working as expected after following my guide. I wrote the thing from memory, after spending 3 days rooting my phone and figuring everything out from various sources. Hopefully this saves people some time where they don't have to piece a dozen sources together to figure out how to do it. I only mentioned the main 4 I referenced, but there were other lessons learned from various places that aren't covered in those posts.
JacekRing said:
I've modified the guide appropriately, to resolve all of the issues (I think) you mentioned. And to make some steps easier to understand and follow.
I also added a recommended app on the bottom, and mentioned a site you can use to get PlayStore apps which will now list as incompatible with our phones.
Finally, question: Did you succeed using this Guide? Just curious if everything is working as expected after following my guide. I wrote the thing from memory, after spending 3 days rooting my phone and figuring everything out from various sources. Hopefully this saves people some time where they don't have to piece a dozen sources together to figure out how to do it. I only mentioned the main 4 I referenced, but there were other lessons learned from various places that aren't covered in those posts.
Click to expand...
Click to collapse
I was quite successful with the root. Even though I messed up a few times (skipping steps), it all works out and now it's working lovely. It only took an hour of actual work, plus a lot of download time because of slow hosts.
Thanks so much for the guide, the only issue was with the slow hosts, and that's hardly your fault. I do wonder if maybe setting up a torrent of the heavier files might help though.
Edit: I will say, this is a wonderfully tedious root effort.
jwp1299 said:
I was quite successful with the root. Even though I messed up a few times (skipping steps), it all works out and now it's working lovely. It only took an hour of actual work, plus a lot of download time because of slow hosts.
Thanks so much for the guide, the only issue was with the slow hosts, and that's hardly your fault. I do wonder if maybe setting up a torrent of the heavier files might help though.
Edit: I will say, this is a wonderfully tedious root effort.
Click to expand...
Click to collapse
An hour..........I spent 2 hours watching kingroot try and root my damb phone, LOL because I didn't wipe before trying to get temporary root the first time you use it (before I read in a post that wiping twice will make it MUCH more successful). Took me 10+ hours of actual work to get my phone rooted and CM 13.0 setup, because I didn't have steps to follow, LMAO. Made it up as I went.
As to the Torrent, I'd be the only one sharing and my upload speeds are not that great. maybe 500 kbps, I live in a rural area. At least my download speed is 40 mbps.
And it is hellofa tedious root for the Note 4, I haven't seen any other phone as crazy tedious to root.
Edit: Mind if I add a 'success story' section and add you to it?
JacekRing said:
An hour..........I spent 2 hours watching kingroot try and root my damb phone, LOL because I didn't wipe before trying to get temporary root the first time you use it (before I read in a post that wiping twice will make it MUCH more successful). Took me 10+ hours of actual work to get my phone rooted and CM 13.0 setup, because I didn't have steps to follow, LMAO. Made it up as I went.
As to the Torrent, I'd be the only one sharing and my upload speeds are not that great. maybe 500 kbps, I live in a rural area. At least my download speed is 40 mbps.
And it is hellofa tedious root for the Note 4, I haven't seen any other phone as crazy tedious to root.
Edit: Mind if I add a 'success story' section and add you to it?
Click to expand...
Click to collapse
Oh of course, go ahead and add me.
Also, if you do end up making a torrent, i'd be happy to help seed at least for a while. I have pretty good upload and no data caps or anything so it would probably help a bit (anything is faster than that 100 kbps that xda was giving)
You called N910VVRU2BPA1_N910VVZW2BPA1_VZW.zip, "N910VVRU2BPA1 Full Firmware". Which kinda got me confused, (maybe its just me trying to do this at 1 am >_>) but might want to edit that. Other then that Iv'e had a pretty easy time following this guide. Thanks! (still doing it fyi, I got an infinite bootloop, so figured I messed up somewhere after reflashing TWRP, now im starting from scratch.)
I have a Very weird problem , I followed your instructions correctly i was on step 25 did exactly what you said pulled the unpluged the USB and pulled the battery and and waited 5 seconds and put the battery back in and rebooted the phone only problem is now it is stuck in a boot loop of the image Samsung galaxy note 4 and just keeps rebooting . I haved tryed doing a factory reset and wiping cache and reinstalling 5.1..1 via odin and it is still doing the boot loop i am not sure what i did wrong or what to do . I know its not hard brick because i can get into recovery and download but just wont boot the past the Samsung not 4 logo
---------- Post added at 05:05 AM ---------- Previous post was at 04:57 AM ----------
Ok so i went and wiped and factory rest like 10 times and now it got past the screen So that is a relief lol
Viper-Link said:
You called N910VVRU2BPA1_N910VVZW2BPA1_VZW.zip, "N910VVRU2BPA1 Full Firmware". Which kinda got me confused, (maybe its just me trying to do this at 1 am >_>) but might want to edit that. Other then that Iv'e had a pretty easy time following this guide. Thanks! (still doing it fyi, I got an infinite bootloop, so figured I messed up somewhere after reflashing TWRP, now im starting from scratch.)
Click to expand...
Click to collapse
Not sure what to tell you viper as not enough info. Hope you figured it out...
pfcland said:
I have a Very weird problem , I followed your instructions correctly i was on step 25 did exactly what you said pulled the unpluged the USB and pulled the battery and and waited 5 seconds and put the battery back in and rebooted the phone only problem is now it is stuck in a boot loop of the image Samsung galaxy note 4 and just keeps rebooting . I haved tryed doing a factory reset and wiping cache and reinstalling 5.1..1 via odin and it is still doing the boot loop i am not sure what i did wrong or what to do . I know its not hard brick because i can get into recovery and download but just wont boot the past the Samsung not 4 logo
---------- Post added at 05:05 AM ---------- Previous post was at 04:57 AM ----------
Ok so i went and wiped and factory rest like 10 times and now it got past the screen So that is a relief lol
Click to expand...
Click to collapse
Was this after the first time you inputted the adb commands our second? Make sure you pull the SD card after the second time, as it will cause reboots after the second time until you reformat the SD card on your PC. Size will be wrong on PC but size will fix when you reformat the SD card a second time on your phone.
Edit it creates like 20 partitions on the ad card when you do adb, it creates a backup of your phone os.

Nook Glowlight Plus 7.8 2019 (NGP7.8, BNRV700)

This one20092011201220132015201720192021Nook v1 Nook Simple TouchNook Simple Touch w/ GlowlightNook GlowlightNook Glowlight PlusNook Glowlight 3Nook Glowlight Plus (7.8 inch)Nook Glowlight 4
The other one
The 2019 Glowlight Plus shares the same name as the 2015 release. To avoid confusion, people began referring to it as the Glowlight 4, a name later used for the 2021 Nook release (surprisedpikachu.jpg). While the 2019 Nook is both confused with the 2015 and 2021 Nooks, it is less common than either. This makes it difficult to find compatible resources and tutorials.
This thread is for collecting the available resources for the 2019 Nook in one place, and eventually building a step-by-step guide for unlocking the potential of the device.
Why the BNRV700?
Three years after its release, it's currently the cheapest option for a reader with a screen size ideal for large format PDFs, such as textbooks. As of writing, the Nook Glowlight Plus (2019) can be found for half (or less) the price of other options with a similar display.
Unfortunately, the Nook ships with poor support for PDFs, sluggish hardware, severely outdated firmware (Android 4.4.2, released 2013) and lacks additional features like expandable storage. Some of these issues can be remedied, meaning the Nook could be a great option for many people, but only if it's safe and convenient to expand its functionality.
If you know of any useful resources or guides, please leave them in the comments below.
Note: This is an early work in progress. As of writing this, I don't have the device yet.
I'm reserving this space to put any resources, or document my experience with rooting or recovering the Nook Glowlight Plus 7.8 2019 (NGP7.8, BNRV700).
Resources
Technical
Hardware overview: Temblast​Backup and Recovery
TWRP: Github​Neo Noogie: Temblast, XDA-thread​Rooting
Magisk Root guide (Glowlight 4): Mobileread-thread​Caution: This guide is specifically for the Glowlight 4 (2021) rather than the Glowlight Plus 7.8 (2019) but it might be applicable.​RootGLP-3 script (Glowlight 3): XDA-thread​Caution: This resource is for the Glowlight 3 (2017) rather than the Glowlight Plus 7.8 (2019), however it has been reported to work.​RootGLP-3 script (2019 Glowlight Plus): XDA-thread​Note: This is a small modification of the Glowlight 3 (2017) root script for the 2019 Glowlight Plus, from wgznz (Chinese).​Firmware
Alternate ROM: XDA-thread​Software
Installing a launcher:​Installing apps:​Compatible readers and utilities:​Adding wallpapers:​Adding a software back button:​Physical button remapping:​Hardware
Expandable storage mod::​
High risk or incompatible resources
Mods
NGP Exposed module with fast refresh: Mobileread-thread​Supported: Nook Glowlight Plus (2015), Nook Glowlight 3​Notes: Due to the similarities between the NG3 and NGP7.8 (2019), someone might be able to get this to work, but it's untested.​
jun127 said:
I think more people would be willing to try it. But, between confusing and inconsistent naming making searches difficult (now even worse with the "Glowlight 4") and a lack of step-by-step guides, it's a minefield for the casual user to modify, and most aren't interested in the sub-standard Nook software.
Click to expand...
Click to collapse
I don't know whether you saw this and then dismissed it or just missed it: https://forum.xda-developers.com/t/gp-g3-gp7-8-twrp-alternative-firmware.4074347/
Seems like that might address most of the issues you have expressed.
nmyshkin said:
I don't know whether you saw this and then dismissed it or just missed it: https://forum.xda-developers.com/t/gp-g3-gp7-8-twrp-alternative-firmware.4074347/
Seems like that might address most of the issues you have expressed.
Click to expand...
Click to collapse
It looks like it could be a useful resource, but it seems like a lot of steps and cautions are ommitted. Although I've installed TWRP, rooted, and installed the fastink kernel (among other mods) on my old NST, I would hesitate (especially as a new user) to install alternate firmware without a clear procedure to first backup and revert everything to factory defaults or recover if something goes wrong.
Rough draft / work in progress (proceed at own risk)
Getting started
Download and install ADB
Using Android Studio
1: Download Android Studio
2: Scroll down and click on “SDK Tools Only”
3: Click on “ADB, Fastboot, and Platform Tools” and then click on the “Download” button.
4: After “adb_setup-x86.exe” is downloaded by the installer, run it and install adb inside the android SDK folder.
Using Minimal ADB and Fastboot
1: Download the installer or portable version (See: original XDA thread, latest version 1.4.3, 2018).
2: Install and run
Note: If you use the portable version, commands should be ran from the same directory. To open a console in the current folder on Windows, select the address bar, type cmd and hit enter.​
Enable USB debugging through developer options
1: Unplug the nook from the computer and turn the Nook on, register an account with Barnes and Noble and finish setting the device up.
2: Pull down the top menu
3: click "see all settings"
4: Press the down error on the bottom of the menu to go to the second page of settings
5: Press "about"
6: Tap the Nook logo until developer mode is enabled
7: Press "developer option settings"
8: Enable the "usb debugging" option
9: Connect the Nook to your computer. A popup will appear on your Nook asking to "turn on USB mode to safely move files..." click OK.
Note: This will cause your computer to download the appropriate drivers. After the drivers have been installed your Nook will show up in Windows Explorer and the Device Manager.​Note: When running commands over USB, sometimes it's necessary to temporarily disable mass transfer mode. To do this, go back to the developer options menu and select "disable mass storage".​Important: Remember to re-enable mass storage mode if you would like to drag-and-drop files onto your device using Windows file explorer later.​
Backup and restoration
The two most popular methods of creating and restoring backups are TWRP and Neo Noogie. If possible, it's best to have a backup from both. However, if you're not comfortable using the command line in Windows, you may choose to use TWRP only. Neo Noogie is a more powerful (complete) backup method, but it's easy to accidentally format your device or write a backup to the wrong Windows drive, either of which could be a nightmare.
TWRP is recovery software that is installed to the device, and provides a menu to backup and restore parts of the device to internal memory. You'll have to copy the recovery files from your device afterwards.
Neo Noogie can either be installed like TWRP or booted with fastboot. When booted into Neo Noogie, the entire flash memory is served to Windows and appears as a raw unformated drive. The internal storage can then be copied with special software. This has the advantage over TWRP in that it can be used to backup every aspect of your device, but you have to be very careful not to accidentally format the drive in Windows, as it could brick your device.
TWRP
Download TWRP
1: Download twrp_quill.img (may, 2020) from https://github.com/Ryogo-Z/nook_ntx_6sl_twrp/releases
2: Move twrp_generic to a folder (such as Documents\Nook)
Install TWRP
3: Power the NOOK BNRV700 off.
4: Hold the U button and then the power button until it starts into fastboot mode.
5: Connect the Nook to a Windows computer with USB, the drivers should be installed automatically.
6: Open the command prompt or Minimal ADB and Fastboot
7: Navigate to the folder you saved the TWRP image in (ex. starting from your user directory, enter "cd Documents\Nook").
8: Enter fastboot flash recovery twrp_generic.img to install TWRP
9: Enter adb reboot recovery (or interrupt startup 5 times) to enter TWRP recovery mode
Create backup with TWRP
Notice: (TWRP will not backup /storage/spsd as well as /data/media, which in practical terms means ...xyz...)
1: (I don't have a Nook anymore as my NST screen isn't working and haven't used TWRP in 10 years. I imagine it's something like boot into recovery/TWRP > Backup > check all the options > run)
2: Plug the Nook into the computer
3: Select USB mass transfer protocol
4: Open the Nook in file explorer and find wherever the recovery was saved to
5: Copy it to a safe place, like documents\nook.
Uninstall TWRP / reinstall stock recovery
The Nook's update file, 'update.zip' contains a copy of the stock recovery which can be reinstalled if you wish to return the Nook to factory defaults. However the stock recovery has fewer recovery features - so it is always safest to keep TWRP installed if you are tinkering with the device.
Rooting
Root Guide for the 2019 Glowlight Plus (using rootGLP)
1: Ensure you've enabled USB debugging tools from the developer options menu and saved a backup to a secure location
2: Connect the Nook to your computer. A popup will appear on your Nook asking to "turn on USB mode to safely move files..." click OK.
Note: This will cause your computer to download the appropriate drivers. After the drivers have been installed your Nook will show up in Windows Explorer and the Device Manager.​3: Disconnect the Nook and go back to the developer settings menu (see steps 2.1) and select "disable mass storage".
Note: This will prevent USB mode from interfering as we run the ADB script.​3: Download rootGLP.rar
Note: this is the same root script for the Glowlight 3, updated with the correct device name BGRV700. The original can be found in this XDA-thread. For a root guide for the Glowlight 3 using rootGLP, see this XDA-thread. The source is the wgznz forum (Chinese).​4: Extract rootGLP
Note: It's best to run the script from a location like C:\rootGLP\ or D:\rootGLP\.​5: Run the rootnook.cmd
Note: After the process is complete, you will see superSUfree appear on the screen. You will still need to install an alternate launcher.​
Installing apps
Installing a launcher and apps (doesn't require root)
If you haven't installed ADB, you can use the copy of adb.exe in the rootGLP-3\bin\ folder by following the instructions below. After installing a launcher, you should consider installing a file browser (such as ES file explorer) and a better web browser, so that you can download and install apps without connecting to your computer.
1. Make sure you have enabled USB debugging tools from the developer options menu and saved a backup to a secure location
2. Navigate to the rootGLP-3\bin\ folder.
3. Place the launcher .apk inside the bin folder with adb.exe.
4. Click the address bar in Windows Explorer and type "cmd" without quotes and hit enter. A windows CMD terminal will open at the current folder address.
5. type adb install launchername.apk (replace with the name of your .apk file)
Note: kk launcher and text launcher are known to work.​6. When you hit the U-shaped home button on your Nook, it will prompt you to select a launcher and ask if you would like to set it as the default. I recommend using "only once" at least until you can ensure you can always get back to the default launcher from whatever Android 4.4.2 compatible launcher you choose.
Installing KOreader and getting pageturn buttons working in KOreader (no root)
1. Download KOreader apk from https://koreader.rocks/
2. make sure your device is connected to adb and authorized with adb devices, if it t says "unauthorized", go to the developer menu (nook home > top right > all settings > page 2 > more > repeatedly tap logo) and tap "allow debugging".
3. install adb install koreader.apk. just hit tab to autocomplete the actual apk name.
4. Create a textfile "event_map.lua" in notepad and copy paste the following keymappings:
Code:
return {
[141] = "RPgBack",
[142] = "RPgFwd",
[140] = "RPgBack",
[139] = "RPgFwd",
}
5. use command adb push event_map.lua /sdcard/KOreader/settings/ to push the event map to the koreader settings.
6. If you had already installed and started KOreader before and just want to fix the keymapping, restart KOreader for the new settings to work (launcher > settings > apps > KOreader > force stop > home button > open KOreader > open book > test buttons > enjoy.
The stock recovery is not a big deal. It's in every update.zip
Just flash it with fastboot.
Why do you want it anyway when either TWRP or NeoNoogie is more powerful?
jun127 said:
It looks like it could be a useful resource, but it seems like a lot of steps and cautions are ommitted. Although I've installed TWRP, rooted, and installed the fastink kernel (among other mods) on my old NST, I would hesitate (especially as a new user) to install alternate firmware without a clear procedure to first backup and revert everything to factory defaults or recover if something goes wrong.
etc.
Click to expand...
Click to collapse
I am not the person to ask, but you are right that the first step is to be sure you can restore the device to stock. I'm one of those eccentrics who still loves and uses and continues to develop little improvements for the original NST/G, so all this fastboot stuff is pretty meaningless to me. I've flashed custom ROMs on Nook Tablets, but that's a totally different operation since back in the day Android was not locked up so tightly.
If you jut want a root guide (but it sounds like you want more than that): https://www.mobileread.com/forums/showpost.php?p=4202391&postcount=391
nmyshkin said:
I am not the person to ask, but you are right that the first step is to be sure you can restore the device to stock. I'm one of those eccentrics who still loves and uses and continues to develop little improvements for the original NST/G, so all this fastboot stuff is pretty meaningless to me. I've flashed custom ROMs on Nook Tablets, but that's a totally different operation since back in the day Android was not locked up so tightly.
If you jut want a root guide (but it sounds like you want more than that): https://www.mobileread.com/forums/showpost.php?p=4202391&postcount=391
Click to expand...
Click to collapse
I'd like to put together a simple guide, similar to what I wrote for the original NST about 10 years ago. I think the device needs a roadmap to outline what is currently possible in terms that are easy to follow. The device seems like it has a lot of potential, but it's just not very accessible at the moment.
I watched your video on running the CM on the NST, very interesting stuff and I'm glad to see some people are still keeping the device alive. I had used the original NST as a smartphone for a (short) while, even using it with Google phone and Whatsapp. It was surprisingly functional and, with the right optimizations, the battery could seemingly last forever with light use. Although it otherwise held up well, the rubber front panel and soft-touch back eventually degraded into a gooey mess. Removing the soft-touch coating on the back shell and replacing the rubber on the front with leather made it a more enjoyable reading experience for a while. Unfortunately, very poor app availability on Android 2.1 and the small, relatively low resolution display made it almost unusable for large format PDFs. Ultimately, the screen started failing and although it's still worth fixing, after 10 years it's overdue for an upgrade.
Renate said:
The stock recovery is not a big deal. It's in every update.zip
Just flash it with fastboot.
Why do you want it anyway when either TWRP or NeoNoogie is more powerful?
Click to expand...
Click to collapse
There's some peace of mind in knowing how to return things to exactly where you started. Even if unnecessary, there's always the possibility of some unforeseen issue and having a clear roadmap that you can follow to get back to the very beginning makes a difference in my mind.

Categories

Resources