Android SD problem!! - HD2 Android Q&A, Help & Troubleshooting and Genera

I am trying to install an android rom from the SD card with MAGLDR but eatch time it starts to boot i get stuck on GO GO GO! thing...any help please?

have you tried different ROMs? try to format the card again & st it to Primary, experiment with 32k or 64k.
BTW how did you install the magldr?

mengfei said:
have you tried different ROMs? try to format the card again & st it to Primary, experiment with 32k or 64k.
BTW how did you install the magldr?
Click to expand...
Click to collapse
I installed MAGLDR by entering bootloader mode bla bla bla...whats st it to Primary?it seems like its starts the installation and then lags on GO GO GO!

tsagas said:
I installed MAGLDR by entering bootloader mode bla bla bla...whats st it to Primary?it seems like its starts the installation and then lags on GO GO GO!
Click to expand...
Click to collapse
Format your SD card to FAT32 and make sure this partition is set as the primary partition. If you haven't yet created an EXT3/4 partition on your SD card then you won't have anything to worry about. If you didn't understand a word of that, then chances are you just need to format it and not worry about a thing

Nigeldg said:
Format your SD card to FAT32 and make sure this partition is set as the primary partition. If you haven't yet created an EXT3/4 partition on your SD card then you won't have anything to worry about. If you didn't understand a word of that, then chances are you just need to format it and not worry about a thing
Click to expand...
Click to collapse
my card is already FAT32...that s what worries me:/

tsagas said:
my card is already FAT32...that s what worries me:/
Click to expand...
Click to collapse
Yeah but just format it. It solves a lot of problems. Note that this will delete everything which is on your card.

Nigeldg said:
Yeah but just format it. It solves a lot of problems. Note that this will delete everything which is on your card.
Click to expand...
Click to collapse
already done it a couple of times and still nothing...

1- copy folder (Android) to SD Card .
2- Boot in MAGDLR powering on your phone while you press the power button until MAGDLR appears.
3- Select "SERVICES"
4- Select "BOOT SETTINGS"
5- Select "AD SD Dir"
6- Select the "ANDROID" folder or the folder where you dropped the rom.
7- Now select "BOOT AD SD" and wait boot
Did you install this way, didn't you?

powerofthink said:
1- copy folder (Android) to SD Card .
2- Boot in MAGDLR powering on your phone while you press the power button until MAGDLR appears.
3- Select "SERVICES"
4- Select "BOOT SETTINGS"
5- Select "AD SD Dir"
6- Select the "ANDROID" folder or the folder where you dropped the rom.
7- Now select "BOOT AD SD" and wait boot
Did you install this way, didn't you?
Click to expand...
Click to collapse
of course i did installed it this way...but on step no7 i waited forever to boot on GO GO GO!

tsagas said:
of course i did installed it this way...but on step no7 i waited forever to boot on GO GO GO!
Click to expand...
Click to collapse
Hmm, it's always possible that your SD simply isn't compatible with MAGLDR, mine for example cannot be seen when I go to AD SD Dir and I therefore cannot boot any SD ROMs
Sent from my NexusHD2 using XDA

Nigeldg said:
Hmm, it's always possible that your SD simply isn't compatible with MAGLDR, mine for example cannot be seen when I go to AD SD Dir and I therefore cannot boot any SD ROMs
Sent from my NexusHD2 using XDA
Click to expand...
Click to collapse
yes...but mine is compatible...if it wasn't i wouldn't be able to choose zip from sd right?

Nah, I can do that, but I can't choose the AD SD Dir in MAGLDR. CWM seems to be an exception somehow. If your card happens to be a Kingston 16GB Class 4 then it definitely won't work, I'm afraid. Dunno about other types of SD card though.
Sent from my NexusHD2 using XDA

i had that problem too. redownload the rom again and check the md5 sum, if possible. then flash it again..
mine had the wrong checksum and stucked at GO GO GO! too.

chugga said:
i had that problem too. redownload the rom again and check the md5 sum, if possible. then flash it again..
mine had the wrong checksum and stucked at GO GO GO! too.
Click to expand...
Click to collapse
what's that md5 sum mate?

Related

Getting Frustrated,Still cant Get Clockwork Mod Working

hey guys
i followed all the instructions, on the Clockwork Mod thread,ive even fully formated my sd card,getting really anoyed now,any help would be appretiated
TheiPhoneKiller said:
hey guys
i followed all the instructions, on the Clockwork Mod thread,ive even fully formated my sd card,getting really anoyed now,any help would be appretiated
Click to expand...
Click to collapse
Same here. Maybe its something to do with UK Hd2's.
I followed all the instructions too, and kept getting stuck in the boot screen loop.
Back to Nand for me... one thing, on screen before screen to flash zip it says can't find misc, even when I make a misc folder it makes no difference. Good luck to you anyway.
Garrylufc said:
Maybe its something to do with UK Hd2's.
Click to expand...
Click to collapse
Works fine for me, so it's not that.
TheiPhoneKiller said:
hey guys
i followed all the instructions, on the Clockwork Mod thread,ive even fully formated my sd card,getting really anoyed now,any help would be appretiated
Click to expand...
Click to collapse
Can you tell us what you're doing and what happens?
i Copy contents of copytosdroot folder to the root of my sd.then i boot into magldr and go into USB Flasher whilst still connected to my laptop,Run DAF,when thats done i again boot into magldr and tap Boot AD SD but it keep failing to go into Clockwork,i keep getting soming like k:Music/zimage not found or failed to load kernal even tho ive fully formated my sd,its really anoying,i cant try out any new roms exept nand,Really frustrating
I had problems running like this initially - what worked was putting the 'copytosd' files in a folder on the SD Card (I used 'ADSD'), then changing the Boot AD SD folder option in the Settings menu to that new folder ('ADSD').
Then try using 'Boot AD SD' option.
For some reason it did not like the root folder initially (though it now seems to work fine).
Use Panasonic SD Card formatter & re format the SD card & try again, I had the same issues but now its resolved..!!!
Uvaavu said:
I had problems running like this initially - what worked was putting the 'copytosd' files in a folder on the SD Card (I used 'ADSD'), then changing the Boot AD SD folder option in the Settings menu to that new folder ('ADSD').
Then try using 'Boot AD SD' option.
For some reason it did not like the root folder initially (though it now seems to work fine).
Click to expand...
Click to collapse
Guys,
Mine works as well so not a UK issue
Did you follow the instructions using DAF and indicated that it was successful but when you try to 1: boot from sd nothing happens or it flashes and returns to the MAGLDR screen?
I had an issue with the root folder as well, create a folder \recovery and copy the 2 root files intrid.gz and zimage to the \recovery and goto services and change the boot to folder to \recovery.
Important reboot before trying as MAGLDR does not change the folder until after a reboot.
Boot from SD and should be OK
Or at least was for me
Now Nand has came out it has inspired a lot to create their own Android builds and new chefs make mistakes. Not trying to blame chefs in general but some do make mistakes.
Also when we used to load up the builds from SD card, I would say 8 times out of 10 I would use a data.img which hasnt been used before. Now if you go from a Sense build to a non-Sense build, and you are using a data.img in app2sd, then they are not properly matched so a-b might go to a-c and miss b out if you know what I mean. What I do is use a data.img for Sense, another for Sense HD/Z, another one for Gingerbread and another for Miui and these are on my Desktop. When I load up a different builds like Sense to Miui, then I will move the data.img from .data or data2sd folder off the memory card and then overwrite the data.img I have on the Desktop for Sense and replace it for my Miui data.img.
I know it sounds tedious but I found it to help.
Also for the new App2SD+, I create the partition using ClockWorkMod instead of another application. I will use Partition Wizard for Windows to delete a partition and resize the fat32 partition back to the full use of the memory card but always partition and create EXT3 partition using ClockWorkMod.
Hope this helps.
waspsl said:
Guys,
Mine works as well so not a UK issue
Did you follow the instructions using DAF and indicated that it was successful but when you try to 1: boot from sd nothing happens or it flashes and returns to the MAGLDR screen?
I had an issue with the root folder as well, create a folder \recovery and copy the 2 root files intrid.gz and zimage to the \recovery and goto services and change the boot to folder to \recovery.
Important reboot before trying as MAGLDR does not change the folder until after a reboot.
Boot from SD and should be OK
Or at least was for me
Click to expand...
Click to collapse
i have a slightly different problem: I can boot into clockwork recovery after copying the copy-to-sd files and use it as a partitioning tool. But cant actually complete the installation as I keep getting errors when i run the DAF file from CWM folder in USB flasher option of MAGDLR, so cant actually use it for recovery !!!!

Rom Issues Please Help

Hi,
I am trying to install this rom:
http://forum.xda-developers.com/showthread.php?t=1326217
I recently bought a new sd card from 1 gb to 16 gb as I like Sense roms.
My procedure is as follows:
step1) task 29:
turn off phone
turn on holding volume down-so you'll go to bootloader screen
be sure you see 'usb' in screen (not 'serial')
in nand toolkit click task29 and choose proper options in each screen.
step2) flashing radio:
in phone go to bootloader screen again
in nand toolkit at bottom click browse an find your radio.nbh in pc then click install RUU(when it comes to 96% it will wait for a while its normal)
step3) flashing mgldr:
in phone go to bootloader screen
in toolkit click install mgldr(at bottom)
4) now in mgldr go to usb flasher.be sure you see usb flasher.....usb in screen
in nand toolkit choose mgldr repartition (at left top)
choose 400mb partition size(at left)
write 4 instead of 45 as cache size
click repartition at right bottom.so you'll have repartitioned your nand.
5) mgldr menu go to ad recovery-advanced-partition sd card-1024-0
(so you'll have an sd-ext partition of 1gb which is necessary for this and many other roms)
then in mgldr menu (you can go to this menu by rebooting or pulling out battery) go ad recovery-mounts and storage-mount usb storage-when pc sees phone, send rom to phone
6) mgldr menu-ad recovery-install zip from sd-choose zip from sd-find your rom and choose with call button-after installation is complete reboot phone-after approximately 20 minutes the phone will be ready.
Where am I going wrong?
So?
Where are you stuck ? (What is the problem ?)
Marvlesz said:
So?
Where are you stuck ? (What is the problem ?)
Click to expand...
Click to collapse
After doing all that, I get a message saying " kernal missing" or something along those lines.
Is the above procedure correct ?
Why dont you try all of your steps mentioned except 2 & 5?? A new radio does not need to be flashed every time. Also the systemshouldcreate its own partion upon boot.
Sent from my Transformer TF101 using xda premium
Wait step 5 is wrong. Mass storage within magldr is glitched. You need to use a card writer to put your rom onto your sd card. Sorry i didn'tcatch that at first. Also you still should not have to flash a new radio everytime.
Sent from my Transformer TF101 using xda premium
kylew1212 said:
Wait step 5 is wrong. Mass storage within magldr is glitched. You need to use a card writer to put your rom onto your sd card. Sorry i didn'tcatch that at first. Also you still should not have to flash a new radio everytime.
Sent from my Transformer TF101 using xda premium
Click to expand...
Click to collapse
Do you know why it would give the message when turning on "Kernal missing"
xda_apprentice said:
Do you know why it would give the message when turning on "Kernal missing"
Click to expand...
Click to collapse
Its something about transferring data, I'm not certain exactly what. I would assume the file isn't transferred right over magldr interface and somehow parts of the rom become not right for lack of better terms. I read once to not transfer files using magldr because 1.13 is glitched. I'm not 100% sure what it is. Just try a card reader and see if that helps. Unless your dual booting I prefer clk .
Sent from my HTC HD2 using xda premium
What exactly does it do turning on? Kernal missing .. does it boot loop, freeze or restart?
Sent from my HTC HD2 using xda premium
Step 5.5 ... in cwm - mounts and storage (or something) - mount SD card - copy over your rom.
This will show your SD on the PC, and unlike the magldr USB storage the cwm one works. No card reader necessary.
samsamuel said:
Step 5.5 ... in cwm - mounts and storage (or something) - mount SD card - copy over your rom.
This will show your SD on the PC, and unlike the magldr USB storage the cwm one works. No card reader necessary.
Click to expand...
Click to collapse
I normally just mount and copy it over and that copies it over.
But the problem is after flashing, when magldr starts I get a message in the lines of "Kernel missing" and it stops.
Does my steps differ to anything you would suggest?
xda_apprentice said:
I normally just mount and copy it over and that copies it over.
But the problem is after flashing, when magldr starts I get a message in the lines of "Kernel missing" and it stops.
Does my steps differ to anything you would suggest?
Click to expand...
Click to collapse
So it never gets past magldr?
Sent from my HTC HD2 using xda premium
xda_apprentice said:
I normally just mount and copy it over and that copies it over.
But the problem is after flashing, when magldr starts I get a message in the lines of "Kernel missing" and it stops.
Does my steps differ to anything you would suggest?
Click to expand...
Click to collapse
Just follow your steps minus the radio flashing as you only have to do this once (which I'm sure you have already done since you have been using custom roms). Then instead of using MAGLDR to transfer the rom, boot into CWR first and then using mounts and storage, transfer it there. It sounds like MAGLDR is corrupting the file transfer (as it usually does).
Just start over with task29 then skip the radio flashing and adjust your steps to transferring the rom over through CWR.
chrisrj28 said:
Just follow your steps minus the radio flashing as you only have to do this once (which I'm sure you have already done since you have been using custom roms). Then instead of using MAGLDR to transfer the rom, boot into CWR first and then using mounts and storage, transfer it there. It sounds like MAGLDR is corrupting the file transfer (as it usually does).
Just start over with task29 then skip the radio flashing and adjust your steps to transferring the rom over through CWR.
Click to expand...
Click to collapse
Hey Chrisrj28 (it's been sometime
I see what you mean! Or I could just copy it using sd adapter.
Thanks guys will try that out !

[Q] dual boot android and android sd?

hi,
i cant seem to get this right...am i able to boot adroid from sd with nand android using maglrd??
thx
note:i have searched but it was all wp7/android
walidhazem said:
hi,
i cant seem to get this right...am i able to boot adroid from sd with nand android using maglrd??
thx
note:i have searched but it was all wp7/android
Click to expand...
Click to collapse
Yes you are. Place the Android folder with MAGLDR files on the root of your SD card and then boot into MAGLDR. Select services>AD SD Dir>Android (or whatever your folder name is) then go back to MAGLDR main menu and select 'boot AD SD'.
Nigeldg said:
Yes you are. Place the Android folder with MAGLDR files on the root of your SD card and then boot into MAGLDR. Select services>AD SD Dir>Android (or whatever your folder name is) then go back to MAGLDR main menu and select 'boot AD SD'.
Click to expand...
Click to collapse
oh so basically like usual?
thx man just wanted t confirm
walidhazem said:
oh so basically like usual?
thx man just wanted t confirm
Click to expand...
Click to collapse
Yeah same as WP7

[Q] Magldr Boot Ad SD

Hi,
I notice that some builds can be booted Via Magldr SD,
How do I do this,
I have Runny on NAND,
Do I just download the ROM add it to "Android folder" and hit "Boot AD SD" in MAGLDR?
Thanks,
Alex
Hi Alex,
I don’t think add ROM to Android folder is a good idea in order to not disturb your NAND build. Use different SD or rename your downloaded Android folder lets say Androidsd.
Steps for first boot:
1- Copy folder (Androidsd) to SD Card.
2- Boot in MAGDLR powering on your phone while you press the power button until MAGDLR appears.
3- Select "SERVICES"
4- Select "BOOT SETTINGS"
5- Select "AD SD Dir"
6- Select the "Androidsd" folder
7- Now select "BOOT AD SD" and wait boot
Next boot you can skip steps 3 to 6.
Have fun!
Petricanu said:
Hi Alex,
I don’t think add ROM to Android folder is a good idea in order to not disturb your NAND build. Use different SD or rename your downloaded Android folder lets say Androidsd.
Steps for first boot:
1- Copy folder (Androidsd) to SD Card.
2- Boot in MAGDLR powering on your phone while you press the power button until MAGDLR appears.
3- Select "SERVICES"
4- Select "BOOT SETTINGS"
5- Select "AD SD Dir"
6- Select the "Androidsd" folder
7- Now select "BOOT AD SD" and wait boot
Next boot you can skip steps 3 to 6.
Have fun!
Click to expand...
Click to collapse
When I select AD SD Dir the options are like "#@';"£$%"
they are completely random ?!?
alex.odell.2011 said:
When I select AD SD Dir the options are like "#@';"£$%"
they are completely random ?!?
Click to expand...
Click to collapse
thats fine but does it boot??
i copied nexus ics sd to the root but once i press call to enter to ad sd dir to choose the folder it goes back to the magldr menu and i dont access to sd card
alex.odell.2011 said:
When I select AD SD Dir the options are like "#@';"£$%"
they are completely random ?!?
Click to expand...
Click to collapse
I don't know what folders have you on ÿour SD card. You have to press vol down button till you reach the folder where you drop the ROM
Hi,
The folder is not listed, only these random names !?!
Does the ROM need to be zipped?
Thanks
alex.odell.2011 said:
Hi,
I notice that some builds can be booted Via Magldr SD,
How do I do this,
I have Runny on NAND,
Do I just download the ROM add it to "Android folder" and hit "Boot AD SD" in MAGLDR?
Thanks,
Alex
Click to expand...
Click to collapse
Hi,
I am to a newbie like you, see this thread it might be useful for you.
Also, see this post, you might find it useful.
Best Regards,
Vikas
vikas027 said:
Hi,
I am to a newbie like you, see this thread it might be useful for you.
Also, see this post, you might find it useful.
Best Regards,
Vikas
Click to expand...
Click to collapse
Good guides, but I already have NAND flashed
Just playing with sd card builds
Sent from my HTC Sensation XL with Beats Audio X315e using xda premium
May I ask a similar question? Can I have MAGLDR with winmo 6.5? All of the SD build of ICS I've been seeing only boots with MAGLDR, they don't have clrcad/haret.
ralfkof119 said:
May I ask a similar question? Can I have MAGLDR with winmo 6.5? All of the SD build of ICS I've been seeing only boots with MAGLDR, they don't have clrcad/haret.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1437463
This is a good build, it says magldr but there is a Claret and Haret in there also
You can install magldr to the phone please have HSPL and latest radio installed.
When you install magldr it WILL remove wm6.5 and you will have to re flash a wm6.5 rom to the phone, not the offical one as it will remove magldr,
You could always try flash ICS or WP7, there is a speed boost in nand
Thanks... So installing magldr will wipe my current winmo, and I'd have to flash a cooked winmo rom? Thanks for the info. I'd just like to clarify, so, I CAN have both magldr and winmo 6.5 both at the same time? And I can still switch between an android sd rom and the winmo 6.5?
ralfkof119 said:
Thanks... So installing magldr will wipe my current winmo, and I'd have to flash a cooked winmo rom? Thanks for the info. I'd just like to clarify, so, I CAN have both magldr and winmo 6.5 both at the same time? And I can still switch between an android sd rom and the winmo 6.5?
Click to expand...
Click to collapse
I do belive you can only dual boot WP7 and Android (Windows Phone 7 on NAND & Android on SD Card)
Not to sure about wm6.5 as I am not a dev,
You can defently dual boot wp7 and sd android though
http://www.addictivetips.com/mobile/what-is-magldr-and-how-to-install-and-use-it-on-htc-hd2/
ralfkof119 said:
Thanks... So installing magldr will wipe my current winmo, and I'd have to flash a cooked winmo rom? Thanks for the info. I'd just like to clarify, so, I CAN have both magldr and winmo 6.5 both at the same time? And I can still switch between an android sd rom and the winmo 6.5?
Click to expand...
Click to collapse
Just a thought, practicly all SD builds come with Claret and haret included, if not you can usually download some files or there included,
I think you should install NAND android if you like android or boot Haret and Claret,
sorry if i sound like a ****, I dont mean to be
And magldr WILL remove your WinMo
http://forum.xda-developers.com/showthread.php?t=1033537
Sorry for being misleading, you cannot dual boot WP6.5 and SD android via MAGLDR
:S
Awww... too bad. Can't let go of winmo 6.5 alex, a very important app is still sticking to this OS. ^_^
Thanks for the replies though. I'm happy with android SD for the moment. ^_^
Ok mate good stuff, most builds that say magldr/sd will have claret and haret others usually have a post to add in, good luck mate!
Sent from my HTC Sensation XL with Beats Audio X315e using xda premium
Thanks for thanks :-D
Sent from my HTC Sensation XL with Beats Audio X315e using xda premium
Just to bring this alive again,
Any ideas?
When in BOOT AD SD Dir I get random figures and not folders,
I am running TBD Runnymead with EXT4 partition,
Thanks,
For booting the ROM via MAGLDR follow the following options :
1.) Make sure its the SD build you have downloaded.
2.) Check the startup.txt file for "rel_path=foldername". If you named the folder with android as "Androidsd" then it should look like
"rel_path=Androidsd"
boot
3.) remove anything written after this like nand=1 or wince=1
4.) enter bootloader. When on magldr, go to Services > Boot Settings > AD SD Dir
select "Androidsd" as the directory.
5.) Boot AD SD
then u should be able to boot.
If you are not able to enter AD SD DIR tab, remove the memory card and reinsert.

How to dual boot Latest builds of WP7 and Android JB

Hi I was wondering if anyone can guide me through dual booting the latest WP 7.8 build and Android JellyBean v.1.2. I love both but can't seem to dual boot both. It's either one or the other.Thanks in advance.
try to read this thread
or this
http://forum.xda-developers.com/showthread.php?t=1356833
Iojjj said:
try to read this thread
Click to expand...
Click to collapse
But that forum doesn't say what to do once you install WP7. Like how to install android JB to dual boot both. I want to dual boot the latest builds for both.
Emm... It says you must do reset of you phone from settings (or hard reset from magldr). Then you should don't let your phone boots (just stay in magldr). Remove your card from phone and put it to PC's card reader. Use MiniTool Partition Wizard to create more partitions (fat32 and ext4). And there you go. Try to boot WP7. If it boots normaly just install Android as NativeSD.
You will be lost any of your data on SD.
I think those tutorial is clearly enough. Hope you can repeat all of this steps.
Jcamacho228 said:
But that forum doesn't say what to do once you install WP7. Like how to install android JB to dual boot both. I want to dual boot the latest builds for both.
Click to expand...
Click to collapse
look my video for dualboot on one SDcard in Pdaimatejam topic (i posted link already)
dxdy said:
look my video for dualboot on one SDcard in Pdaimatejam topic (i posted link already)
Click to expand...
Click to collapse
I too, am finding the various tutorials a bit confusing. I used MAGLDR V1.13 and successfully installed Pdaimatejam Rom Wp7.8 OS 7.10.8835.35 v8.5. My goal is to e able to dual boot the installed WP7 and MIUI_JB_2.9.14_NATIVESD. THIS tutorial, was followed to partition sdcard, but I'm still confused when it comes to installing the SDNATIVE Android ROM.
Do I install cwm?
I probably should state that my volume down button in not working by the way.
bibbin said:
Do I install cwm?
Click to expand...
Click to collapse
There is a sentence from those tutorial:
copy the "TOUCH" or "TWRP" or "RECOVERY" folder your SD Card (they all do the same thing)
you should copy recovery folder to sd card.
Jcamacho228 said:
I probably should state that my volume down button in not working by the way.
Click to expand...
Click to collapse
You can do hardreset from WP settings anyway. And magldr has looping menu, I think.
Iojjj said:
There is a sentence from those tutorial:
copy the "TOUCH" or "TWRP" or "RECOVERY" folder your SD Card (they all do the same thing)
you should copy recovery folder to sd card.
Click to expand...
Click to collapse
...and then what?
Maybe you should read more carefully?
Code:
Magldr > Service > Boot Setting > AD SD Dir > TOUCH
& this should run, Tap on Advance
[IMG]http://api.photoshop.com/v1.0/accounts/4ae359774e764cf4ad5fa83d4fca8aa7/assets/398b2592363a4bb698eb746c9fd87413/renditions/1024.jpg[/IMG]
Tap on Partition SD card
[IMG]http://api.photoshop.com/v1.0/accounts/4ae359774e764cf4ad5fa83d4fca8aa7/assets/a1c0832d1e2943b4b61945eabd258d42/renditions/1024.jpg[/IMG]
Ext size. = press the + sign to go up, swap size is 0 & make sure to select EXT4 then tap Partition
[IMG]http://api.photoshop.com/v1.0/accounts/4ae359774e764cf4ad5fa83d4fca8aa7/assets/2a19905a08f94abd822641a8811c82a2/renditions/1024.jpg[/IMG]
All of this is jus REPLACEMENT of recovery. Then :
Code:
Magldr > Service > Boot Setting > AD SD Dir > TOUCH
Tap Install, notice that the compatible ROMS for this methoid have a div2 or NativeSD designation, tap on the ROM you want to flash.
[IMG]http://api.photoshop.com/v1.0/accounts/4ae359774e764cf4ad5fa83d4fca8aa7/assets/15aaf0bf080a4921bf7f45913059f6b1/renditions/1024.jpg[/IMG]
Iojjj said:
Maybe you should read more carefully?
Click to expand...
Click to collapse
lojjj, I too have attempted to follow that series of tutorials, and finally succeeded, but due specifically to the part you are mentioning, it took me HOURS. There is no "Touch", "Recovery" or "Tap" folder on a freshly partitioned SD card with 4extRecovery on it. The instructions are absolutely extraneous and cause confusion. Moreover, instructions for using HD2Toolkit to partition the card are useless for triple booting if one has already partitioned using a card reader in your computer. Yes, it can be done, but doesn't need to be done if one has followed the instructions up to that point.
The other problem is that one needs to combine three or more tutorials just to do this, and they sometimes have different options, but no reason given for choosing those options. This may be the best tutorial out there, pictures and everything, but still a far cry from being perfect or complete. Oh, and sometimes the tutorials are continued in another post, which also leads to confusion.
SK
Sword King said:
There is no "Touch", "Recovery" or "Tap" folder on a freshly partitioned SD card with 4extRecovery on it.
Click to expand...
Click to collapse
You're looking for this ones? The link provides at the top of first post. There are a lot of recoveries with NativeSD support. You need to download one of them, unpack and copy to root of SD Card. And then you can get to Magldr > Service > Boot Setting > AD SD Dir > Recovery.
Maybe I'm wrong cause I never did such things. Good luck :fingers-crossed:

Categories

Resources