My HD2 won't power - Please Help! - HD2 General

I woke up this morning and It appeared that the battery had ran out during the night as the phone was off.
I attempted to turn it on and nothing , plugged in usb charge and nothing (no lights no reaction to me pressing power .. nothing)
I had a spare battery ... nothing
I have tryed hard reset but since I get nothing that also does nothing.
Please help , any ideas?
I have stock winmo6.5 with americandroid running from sd (it would have been running android last night) , no new installs etc being this setup for months

1. First remove battery for some time, let it rest at room temperature.
then put battery with some charge into HD2, double check that battery connectors are clean
2. plug in wall charger into HD2
3. press and hold red reset button inside HD2 case
4. turn on while still pressing red button
5. after some while release red reset button
6. pull out battery repeat from step 1 if it doesn't boot up
try this several times, if this doesn't help you should look into motherboard fault.

retsam88 said:
1. First remove battery for some time, let it rest at room temperature.
then put battery with some charge into HD2, double check that battery connectors are clean
2. plug in wall charger into HD2
3. press and hold red reset button inside HD2 case
4. turn on while still pressing red button
5. after some while release red reset button
6. pull out battery repeat from step 1 if it doesn't boot up
try this several times, if this doesn't help you should look into motherboard fault.
Click to expand...
Click to collapse
Thank you for your reply , I have tried what you suggested but as of yet I have had no luck. Do you have any other suggestions?

you say you had a spare battery, was it charged?
you also said you were running android from SD, would your phone normally boot to android by its self or would it go to WM?
MAGLDR is a bit of a pain when it comes to the battery. if your unsure about the spare battery then get yourself an external charger and charge one up, there is a way of doing this manually with an old USB cable but id suggest get a charger

dazza9075 said:
you say you had a spare battery, was it charged?
you also said you were running android from SD, would your phone normally boot to android by its self or would it go to WM?
MAGLDR is a bit of a pain when it comes to the battery. if your unsure about the spare battery then get yourself an external charger and charge one up, there is a way of doing this manually with an old USB cable but id suggest get a charger
Click to expand...
Click to collapse
It booted up in stock wm6.5 - no rom / radio updated since I got it from HTC , I would then use the file explorer to navigate to the android folder and boot it that way.
99% of the time I would have it running android (only time it was in wm6.5 was when battery ran dead and I had to turn it back on)
The spare battery would have had charge , my friend has the same phone so I shall try her battery tomorrow but I'm thinking its not the battery
The strange thing is that it was working when I went to sleep, and I did nothing to it , no apps installed or roms installed etc and next morning I got nothing!! I MISS MY PHONE lol

Related

Fix for dead hd2 winphone 7 fter battery discharge

Probably the wrong place but this forum is beyond navigation for newbies like me...
if you have let your battery run dry and can no longer charge and get into your win7 hd2, here's how I did it...remove sim and sd card, plug charger in, it will boot and charge again... worked for me...
I'll make sure to keep this in mind, if it works! I'll make an edit to announce my results when that unfortunate day comes.
Pulling the battery out and sticking it back in works too.
NeoGreendawg said:
Pulling the battery out and sticking it back in works too.
Click to expand...
Click to collapse
not for me. if its really discharged and i remove the battery, put it back, the charge led (orange) goes on and after 5sec its off again and nothing happens
NeoGreendawg said:
Pulling the battery out and sticking it back in works too.
Click to expand...
Click to collapse
Nope, that only works if you still have charge left in battery. removing and putting it back in also unlocks it because if you power on phone with USB in it locks for some reason. Well mine does anyway.
If your battery is completley dead then you have no choice (atm) to either charge the battery externally with a dock or by using a USB cable with end cut off (red wire to positive/black to negative).
NeoGreendawg said:
Pulling the battery out and sticking it back in works too.
Click to expand...
Click to collapse
Yes. That's what I also do many times. Never fails
No need to pull out your micro sd, it might cause your rom corrupt. Be careful!
Here's What works for me
Remove the battery .. put it back ... keep the down volume key pressed n press the power key ... THE phone will be on recovery screen... plug THE usb in .. leave it like this for like 15 mins n now reboot . It will be recharged just enuff to power the phone on ... keep the usb plugged and it will start rechaging ...
None of these tricks worked for me, and I didn't want to cut my usb cable...
But I solved the problem with dual boot. Now I can charge my hd2 when it's turned off, and I even have my battery able to charge up to 100%
I presume the phone will not charge if theres not enough power to enter WP7.
I thought the phone would charge by the USB power lead if its turned off.
I guess enter MAGLDR or the Tricolour screen will allow it to charge?
TheATHEiST said:
Nope, that only works if you still have charge left in battery.
Click to expand...
Click to collapse
I've let my phone turn itself off twice since I've been on WP7 and pulling the battery has been enough to get it to boot up far enough to charge both times so maybe I've just been lucky or maybe the phone shuts down before it's completely discharged...
Oh man, this happened to me the other day. Battery died, phone wouldn't hold a charge. Freaked out!! But after some trial and error it worked.
Its not possible to charge the phone when its turned off?
This happened to me when I was still using WinMo. When I connected the phone to charger, it seemed dead (no led light), but after some time (I left it charging over night) it catched up and charged.
This is not possible with WP7? I wouldnt say, that MGDLR could change the way of charging when the phone is off.
keep an external charger for this problem. at least we can hope in the next update of the ROM will solve this problem
In my case, since I fall asleep while listen to music, in morning I wake up, phone already shutdown and can not boot. Even when I plug in, it boot to htc welcome then reboot.
I have tried to pull out the battery and put it back but nothing happen, my phone keep reboot.
So, I pull out the battery and charge with external charger (can charge battery only without phone). Then after 30min put it back then it works.
Thanks god. So be prepare an external charger because WP drain more power then we thought even with the warning 10%. I can not have enough power left for an over night.
This works for me.
This is known maglard issue. This steps works for me every time.
1. Remove battery and after few seconds place it back.
2. Connect your phone with PC through USB
3. Now enter bootloader by pressing Vol Down and Power buttons at same time.
4. Leave it connected for a few minutes.
5. Disconnect your phone from PC and remove battery for a few seconds.
6. Now place battery back and power up your phone.
7. You will start WP7 and now you can continue charging battery normaly.
MGDLR choose last option
it hapens to me and what i have done is in MGDLR I choose last option an it satart charging after some minutes you have to take out the baterry and reboot
it work for me
Happened to me this morning:
1) Took battery out, placed in cradle, put battery in, and held down 'POWER' whilst it booted to MAGLDR.
2) Selected USB Mass Storage Mode, waited for 10 minutes, pulled the battery out, whilst still in the cradle.
3) Re-inserted battery, allowed WP7 to boot, and orange light came on whilst booting, and started charging in WP7.
Thanks to all in this thread!
Nick
Tghe VOL DOWN + POWER works. Happened to me yesterday and after 10 minutes in tricolor I was able to boot.
Bootloader Charges Battery
VICTORY! I was frustrated, and pulling out the battery for a few seconds didn't help at all. Putting the phone in the bootloader (tricolor) screen for 10 minutes worked for me. Phone is back in WP7 and is charging.
No need to pull out battery just hold down power button boot to magdlr main menu leave charger in for 5 mins than boot wp7 (first option in menu) than shud work
Sent from my HD7 T9292 using XDA Windows Phone 7 App

Will not boot, powers down

Last night my battery completely drained so I charged it over night and when I went to power it on it says booting WPH go go go, boots to the HTC green logo screen and powers off. I have been running WP7 flawlessly for 3 weeks now and have not had this problem before. I don't really want to reflash right now because I'm hoping there's a way to salvage everything in the phone.
Are you sure the battery charged last night...reason I ask is...when it completely drains the battery wont charge when the phone is off due to Magldr.
Yeah, it's off the charger right now and it just keeps powering off after the HTC logo
same exact thing just happened to me. I'm going to start from scratch and redo it.
I am curious to know as to what caused this, it's very odd since the ROM has been working flawlessly.
your not restarting with usb cable attached are you?
how did you charge your battery? external charger?
there is some talk that charging in magldr usb flasher mode works dispite no status lights BUT its unclear if the battery controller will auto cut off when full, overcharging could shag your battery
oh a while back i had some odd restart issue too, pretty much as you have mentioned, happened 4 times in a row then worked
Help me too!!!
Me as well, about an hour ago, my battery drained, so I plugged it in, and the phone keeps restarting, but then powers off...
I've kept it on the AC for the past hour, and now it no longer hit's the magldr, it just flashes the screen black, then dies...
Is there a way to JUST CHARGE my battery? Without having it in the phone?
too bad you didnt seach for this issue, i wrote a nice piece that would have got you out of that mess if you hadnt kept restarting it, oh well never mind,
if you cant even get to magldr then your looking at an external charger, you could try connecting up an old usb cable directly to the battery but be very careful!
This happened to my old HD2 after I gave it to my sister once I got my HD7, to enable it to charge again all I did was remove cable, remove battery. Re-insert battery and attach cable, hold down the volume down button on the side of the handset and press the power button.
The phone will turn on and show the tri-color screen. Leave it on this screen for 20 minutes and the battery will charge, then simply reboot and you will be able to boot back in to Windows Phone 7.
TheDisneyMagic said:
This happened to my old HD2 after I gave it to my sister once I got my HD7, to enable it to charge again all I did was remove cable, remove battery. Re-insert battery and attach cable, hold down the volume down button on the side of the handset and press the power button.
The phone will turn on and show the tri-color screen. Leave it on this screen for 20 minutes and the battery will charge, then simply reboot and you will be able to boot back in to Windows Phone 7.
Click to expand...
Click to collapse
Thanks for that tip...I am going to remember it in-case I one day run into the same problem

Tutorial how to recharge phone when battery is drained!

So we all know the major problem with the WP7 roms.
You can not charge your phone when battery is completely drained!
Now here is the solotion. This requires no apps, no mods. Just your own handeling!
So what to do when battery depletes?
1. Plug your phone into a powersuply.
2. Turn on the phone and keep the power button and both volumes buttons pressed. (this is called a hard reset.)
How to hard reset HD2, view the first 17 seconds. Ignore the VolUp!.
3. You will receive an message saying:
''This operation will delete all your personal data, and reset all settings to manufacturer defailt. Press VolUp to restore manufacture default, or press other keys to cancel.''
Click to expand...
Click to collapse
4. Do not press anything. Let your phone be for a couple of minutes. I keep my phone laying for a minimum of 10 minutes.
You won't see the phone charging (no orange light in upper left corner)! Believe me it is!
5. After 10 minutes restart the phone. If ''press any other button to cancel'' does not work. Take out the battery, keep battery out for 5 seconds. Restart phone.
6. Phone will start. After windows phone loading screen you will see the phone is charging. If you kept it on power. If not, you didn't follow my instructions.
Tip: to avoid battery drainage!
When the phone is making the bleep noice warning for critical energy level, turn off the phone and keep it at a warm location. Ideal is to take out the battery and keep that to as warm as possible. Batterys barely drain when they are in warm enviorments.
I am not responsible to any damage done to the phone!
I done this multiple times, all times it worked fine for me!
If it helped, Thank me and leave a comment
when i'm on the road there is only one warm place i could think off, besides my armpits...
but your method works, have faced it once.
Thanks for the conformation.
To bad the HD2, is kinda big... doesnt sit that well.
magldr works as well
whats not clear is if the battery controler is in use with this method, so be warned, dont leave it too long, if you charge it for no more than an hour it will be ok
mains power adaptors usually give out 1Ah, take in to account that the screen is on full, this should give you around 700mA, more than enough to get in to windows to charge propperly
USB charge will be half that, most USB ports only give out 500mAh so an hour will give you approx 200mA again, thats enough to get you in to windows
Overcharging a battery can have some side effects, firstly is reversed polarity, meaning it wont take as much charge in the future, or it could heat up a lot, which isnt good for anything, the life of battery or the device its self.
dazza9075 said:
magldr works as well
whats not clear is if the battery controler is in use with this method, so be warned, dont leave it too long, if you charge it for no more than an hour it will be ok
mains power adaptors usually give out 1Ah, take in to account that the screen is on full, this should give you around 700mA, more than enough to get in to windows to charge propperly
USB charge will be half that, most USB ports only give out 500mAh so an hour will give you approx 200mA again, thats enough to get you in to windows
Overcharging a battery can have some side effects, firstly is reversed polarity, meaning it wont take as much charge in the future, or it could heat up a lot, which isnt good for anything, the life of battery or the device its self.
Click to expand...
Click to collapse
That is true, but I recommend trying it for a minimum of 10 minutes keep it on charge. and as soon as windows pop on it recharges normally.
And didnt knew magldr did the job as well, the only problem is if you deplete it to badly it doesnt go past the HTC screen in the beginning.
all this is completely unnecessary.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
lemonspeakers said:
all this is completely unnecessary.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
Click to expand...
Click to collapse
I did not know that.
Well thank you. Although I am not such a big fan of taking out the battery when its not needed. I mean the change is short circuits with the connecting points when taking out, when powered or putting in when powered it larger. Now I heared from a comment above that MAGLRD does the trick as well. Now that is far more easier then all the others given above, Yours and mine
good tutorial on this. I cant believe the battery wont charge when dead thought this was a faulty error of the phone.
I flash boyppc rom v5 and my battery drained completely and now it doesnt start up I tried both methods available here. Please help.
faiz1120 said:
I flash boyppc rom v5 and my battery drained completely and now it doesnt start up I tried both methods available here. Please help.
Click to expand...
Click to collapse
theres 3 methods on here,
bootloader charge
magldr charge
remove battery charge
all three will benifit frm heating up the battery, do not cook it, or it may blow up
there is a 4th way but i dont recomend it unless nothing else works
take a usb cable mini or usb printer cable
cut off the end connector
strip back the wires and seperate them all, you want the red and black ones
make sure all the wires cant touch each other, cover the 2 unused wires with tape i
then connect the black wire to the (-) negative and the red wire to the (+) positive
tape them in place
the 3rd contact point on the battery isnt used in this method
finally connect the other end of the usb cable to the computer
dont leave it too long and when disconnecting remove the computer end first
faiz1120 said:
I flash boyppc rom v5 and my battery drained completely and now it doesnt start up I tried both methods available here. Please help.
Click to expand...
Click to collapse
I recommend this one.
It bypasses the system somewhat. Don't know what happens when battery is entirely drained, but it is worth a try.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
If it does not help. You can buy a new battery.
Click Here. Its not that expensive, a official new battery from HTC is around 30$is around 20Euro's.
lemonspeakers said:
all this is completely unnecessary.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
Click to expand...
Click to collapse
Thanks for this timely post Lemonspeakers. completely drained the battery listening to music on loudspeaker and didnt hear any warning. Couldn't hard reset then checked this thread.
On putting in the battery after charging the empty phone, the screen kept cycling between mgldr and HTC splashscreen so booted into sd android and the phone is fine.
I assume I didnt charge the empty phone for long enough (30 secs), I didnt warm the battery and I suppose I could have left it cycling until it charged up a bit more.
Thanks again
Toasit said:
I recommend this one.
It bypasses the system somewhat. Don't know what happens when battery is entirely drained, but it is worth a try.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
If it does not help. You can buy a new battery.
Click to expand...
Click to collapse
i tried but my phone doesnt start even then. my friend said it might be a kernel. i wanna flash stock but i dont know how because my phone isnt starting
my hd2 is a tmous. the 1024 one
Robbie P said:
Thanks for this timely post Lemonspeakers. completely drained the battery listening to music on loudspeaker and didnt hear any warning. Couldn't hard reset then checked this thread.
On putting in the battery after charging the empty phone, the screen kept cycling between mgldr and HTC splashscreen so booted into sd android and the phone is fine.
I assume I didnt charge the empty phone for long enough (30 secs), I didnt warm the battery and I suppose I could have left it cycling until it charged up a bit more.
Thanks again
Click to expand...
Click to collapse
your phone was not starting either? like it was black even though you pressed hard reset? how long do i leave it the empty phone to charge??
I "charged" it for about 30 seconds, suppose you could do longer
Robbie P said:
I "charged" it for about 30 seconds, suppose you could do longer
Click to expand...
Click to collapse
I left the phone without the battery and left it plugged in for 2 hrs and still no luck.
faiz1120 said:
I left the phone without the battery and left it plugged in for 2 hrs and still no luck.
Click to expand...
Click to collapse
This would be funny if it wasn't so serious.
Have you tried warming the battery? Hairdryer warm
Dont know if you have mgldr so maybe try the hard reset option
Robbie P said:
This would be funny if it wasn't so serious.
Have you tried warming the battery? Hairdryer warm
Dont know if you have mgldr so maybe try the hard reset option
Click to expand...
Click to collapse
I have magdlr but I can't even get it into hard reset. I can try the hairdryer warm the battery
faiz1120 said:
I have magdlr but I can't even get it into hard reset. I can try the hairdryer warm the battery
Click to expand...
Click to collapse
That might work.
Otherwise maybe a phone repair shop, there is equipment that can charge your battery outside an phone. An emergency charger its called if I am not mistaken.
you could inform there.
its showing symtoms of it bring bricked. cause it doesnt charge, it doesnt turn on without the battery, and yeah conclusion is that its dead!

[Q] Cant boot. Battery wont charge?

hey guys.
charged battery at night used it at work all day came home around 10 and battery was on 1%..went upstairs to charge but phone but was dead. when plugged into wall phone boots for 2 sec then turns off and boots again for 2sec....constantly looping like this? im pretty sure i just need enough charge so that i can boot into android and ill be sweet. but doesn't even get half way there!?
need help. cant charge.
im leaving the battery out for the night and im gonna try again tomorrow but any suggestions would be great!
thanks
Not sure but you can try this: hold down power button till mgldr menu comes. Stay in mgldr menu for some time and get some charge,then reboot.
Sent from my HTC HD2 using XDA Premium App
Phone will not charge on magldr screen. Android needs to be booted to charge.
Get old USB cable, mini or micro, cut end off, bare red and black, take battery, connect red to + and black to - ,plug into wall charger and hold wires on battery for a minute or so, reinsert battery, should be charged enough to get far enough into booting to start charging.
First.. i had the same problem.
it have to charge while off.
before you cut off things, check the batterypins. one of them was broken on my HD2 (i saw one of them below my battery).
if so, try to hold that broken pin back while insert the battery and try again.
you could also buy a dockingstation (something like that: http://www.amazon.com/Fosmon®-Premi...P2YS/ref=sr_1_4?ie=UTF8&qid=1313518480&sr=8-4) to charge batterys.
I had the same problem once, I`m not 100% sure how i solved it but I think that I pluged it in that it started booting and removed then the battery. I think it doesnt start automatically if you reinsert the battery then... but I´m not sure about it...
mmattes said:
I had the same problem once, I`m not 100% sure how i solved it but I think that I pluged it in that it started booting and removed then the battery. I think it doesnt start automatically if you reinsert the battery then... but I´m not sure about it...
Click to expand...
Click to collapse
thats correct, but relies on the bootloader being able to charge when off, so this method of fixing the discharged battery problem only works with winmo or cLK
Your right i had that Problem in the time i was running it with winmob andere haret
Sent from my HD2 using XDA App
Charge while in bootloader or hard reset screen, it should charge from there.
However, the charging process using the aforementioned methods is kind of slow.
hey guys. thanks for your responses. i have left it overnight and it doesnt get to the 1234 bit. i have 3-4 cords so i cut one up however it has blue, red, white and green cords....whats positive and whats negative?
also my pins are fine.
this is killing me!
Thank you to samsamuel, i ended up cutting my old cable. connected the red cable to + and the white cable to - and left it for a hour. just booted my phone back up and got 1000 msgs and emails lol and im on 84% battery.
thanks again to everyone how posted!
much appreciated!
Good to hear,, for anyone else thinking of trying it, an hour is pushing it a bit, you are running the risk of damaging the battery since the charge control circuits aren't being used.
What Android build is this? I remember having a build once that required a special key combination to charge the phone up. I think it required you to hold the volume down and power while plugged in to the charger and it could charge from there. I don't remember exactly though.
mziol said:
What Android build is this? I remember having a build once that required a special key combination to charge the phone up. I think it required you to hold the volume down and power while plugged in to the charger and it could charge from there. I don't remember exactly though.
Click to expand...
Click to collapse
Nothing to do with the build,,, if you have magldr installed the phone must be on and booted into android to charge.
samsamuel said:
Nothing to do with the build,,, if you have magldr installed the phone must be on and booted into android to charge.
Click to expand...
Click to collapse
EDIT: I realize now that it must have been something else, can't charge in HSPL or MAGLDR (duh). I have no recollection of what though (if anybody knows, let me know because it's driving me nuts now!)
OP, you do also realize that instead of cutting up wires you could get an external charger for your battery and just charge the battery alone, right? If you've wanted to buy one of those fancy desk docks you could get one that also charges a battery behind the phone

[Q] HTC HD2 won't turn on<don't recognise Charger or USB

Hi,I have a Android gingerbread 2.3,haspl v.3,MAGLDR113,it's second time my htc block and dont want to restart from the buton,i have remove the battery and it dosnt want to turn on ,there is no screen,the battery was charget,but the red light don't light when i plug the cabel,in my PC dont recognise usb,nothing and the phone,i try for 1 day to remove a battery,but no result,1st time when it happens it work,but for a week i can't use it,Sorry For my English,Some ideas what can i do before i took it back in the store
sounds like it could be a simple flat battery. when magldr is installed you cannot charge the phone unless android is running, so when it is off it does not charge.
if you can try another battery, or your battery in a winmo hd2, that will tell you if its teh battery.
If you have a spare usb cable (any type, doesnt have to be a hd2 micro usb cable) cut end off, bare red and black, hold red to + and black to - on teh battery for about a minute, which should give it enough power to charge.
Also check very carefully that you dont have a bent battery pin from all teh battery in/out. they bend easily.
i hava a Bat charger and charge the bat all night,and the morning it show me that bat is charget,put it on the phone,but nothing ... cant turn on
Maybe battery is dead. Do you own a volt meter an can check the voltage provided by the battery? It shoud show up about 4 volt.
---------- Post added at 08:12 PM ---------- Previous post was at 08:04 PM ----------
Maybe battery is dead. Do you own a volt meter and can check the voltage provided by the battery? It shoud show up about 4 volt.
i took the bat to my friend with devace to check the battery,and everything is OK,but the phone didn't turn on,Can i reinstal the Android ?and how can i do it
Is there a program that can connect to the phone and erase everything
To wipe the phone install the HD2 toolkit, you can download it here.
It includes every tool needed for maintaining your HD2.
Be sure to install the drivers!
Start the program and press the Task29 button, follow the instructions provided. When it's finished your HD2 will be fully wiped, so you would need to reinstall everything.
Do so by doing a MAGLDR repartition. After that choose MAGLDR update recovery to flash the Clockworkmod recovery.
Then go into the Clockworkmod recovery and flash your rom.
Now your HD2 should be fully wiped
BUT! If your PC doesn't even recognize your HD2, and you can't even get to the bootloader screen by pressing and holding both volume down and the "end call" button. Then it's probably a hardware failure.
Maxp101 said:
To wipe the phone install the HD2 toolkit, you can download it here.
It includes every tool needed for maintaining your HD2.
Be sure to install the drivers!
Start the program and press the Task29 button, follow the instructions provided. When it's finished your HD2 will be fully wiped, so you would need to reinstall everything.
Do so by doing a MAGLDR repartition. After that choose MAGLDR update recovery to flash the Clockworkmod recovery.
Then go into the Clockworkmod recovery and flash your rom.
Now your HD2 should be fully wiped
BUT! If your PC doesn't even recognize your HD2, and you can't even get to the bootloader screen by pressing and holding both volume down and the "end call" button. Then it's probably a hardware failure.
Click to expand...
Click to collapse
Magldr repartition flashes cwm so no need for the update recovery step. That's for, well the clue is in the name,,, updating the cwm version on an already partitioned instal.
Okay, thanks for clarifying that!
Didn't know it worked like that, I only use CLK.
Sent from my HD2 using xda premium
thanks for the information,but Isn't happened like I expect,I still cannot to turn the phone on,and still don't recognize USB,Battery is Full,
Everything i try:
Remove a battery for 1 night
Charge a battery with Charger for battery
Put the charge cable into phone for 1 day
try comb. with keys ( volume up/volume down/Power but.,,volume Down and power but.)but nothing happens.More idaes ??? , or maybe never will wake up this phone ???
more information for the problem
htc hd2 1024 mb with Android gingerbread 2.3,haspl v.3,MAGLDR113
Sd card 2 GB (class 3)
while I play games and watching youyube via wifi connection my charge cable was plugged in the phone,in about a 2,3 hours it freeze,i wait 1,2 minutes and after i try to power off the phone I remove the battery and pul back again and in this moment the phone never turn on.That is maybe everything I know if someone knows or give me a idea what to do,please tell me
I've seen this and similar a few times, when left on charge overnight, and upon waking the phone is totally gone. I've woken up to a fully hard reset phone myself, once, not dead but something weird happened.
Electrical surge, perhaps? Overheated circuits? Who knows.
Somehow the phone start,I have put on my router,and plug in USB all night,in the morning i remove a battery,remove a SDcard put back batery,plug usb and it go,I replace infromation from the card with onother sdcard,flash the phone. 10x for the help,maybe now everything is ok
marto9067 said:
more information for the problem
htc hd2 1024 mb with Android gingerbread 2.3,haspl v.3,MAGLDR113
Sd card 2 GB (class 3)
while I play games and watching youyube via wifi connection my charge cable was plugged in the phone,in about a 2,3 hours it freeze,i wait 1,2 minutes and after i try to power off the phone I remove the battery and pul back again and in this moment the phone never turn on.That is maybe everything I know if someone knows or give me a idea what to do,please tell me
Click to expand...
Click to collapse
I've same problem after similar conditions.
Mine is 512Mb HD2 running Andorid on SD
- while using in extreme conditions: very low network signal, hot ambience temperature, using GPS and downloading data throug 3G
- the screen freeze on image and not respond on touch neiter button
-after 2-3 minutes phone temperature became very hot and screen again on freeze
- removed battery (for power off button not responding)
- insert battery
- no power up, no green LED with AV adaptet, no USB recognized
I'll trying to charge battery but i don't have a table battery chager.
Could you please repeat me what you did, since I didn't get the first part, what did you put on your router (what kind of router please)?
I've tried using my phone with another HD2 phone's battery which is working (and which also started with my own battery?!) but my own phone wouldn't start at all with the other battery...
The battery wasn't fully charged, but did it have to be, if so how long should I charge the battery with the cut USB cable for it to be charged enough please?!
TIA
P.S. I've tried a voltmeter on my battery and it said 4.14V (should it be 4V exactly?) and should I even try the cut USB charge trick again (since I've tried another phone's working battery)?
marto9067 said:
Somehow the phone start,I have put on my router,and plug in USB all night,in the morning i remove a battery,remove a SDcard put back batery,plug usb and it go,I replace infromation from the card with onother sdcard,flash the phone. 10x for the help,maybe now everything is ok
Click to expand...
Click to collapse
dada.81 said:
Could you please repeat me what you did, since I didn't get the first part, what did you put on your router (what kind of router please)?
I've tried using my phone with another HD2 phone's battery which is working (and which also started with my own battery?!) but my own phone wouldn't start at all with the other battery...
The battery wasn't fully charged, but did it have to be, if so how long should I charge the battery with the cut USB cable for it to be charged enough please?!
TIA
P.S. I've tried a voltmeter on my battery and it said 4.14V (should it be 4V exactly?) and should I even try the cut USB charge trick again (since I've tried another phone's working battery)?
Click to expand...
Click to collapse
Ok if I understand you correctly you have tried your battery in a working HD2 and it worked. Then you tried the battery from the working HD2 in your device but your device still did not boot up. If this is correct I do not feel your battery is the problem, but still check the battery pins on your device to make sure none of them are not slightly bent and not making contact properly.
Also if you can provide more info on what you may have done to cause this or what happened when your device reached the state it is currently in. This info can help others and me help you better.
I have a similar problem.
The phone won't start, it gets to the white htc screen sometimes but quits within a fraction of a second.
This has been so since the first Android boot hung (I suspect I have not followed the steps accurately enough...). I have charged, decharged and recharged the battery using the suggested USB-cable technique, but this was of no aid so far, so it's not the battery. Pins and all's fine.
It's someone else's phone, too, so it would be rather unfortunate if I bricked it.
Are there any other common reasons for this behavior? Most tutorials rely on a PC connection, but as it does not recognize such a thing, that's a bit of a problem.
Finally the same problem here.
Battery status was about 70% and running smoothly (WinMO Custom Rom) since installed.Unlocked the Screen and tried to start programs.
The Icons were lightened up but nothing happened.Tried to softrestart...Nothing happened.
Removed and reinserted the Battery.
=> Not turning on.
-another fully charged Battery => nothing
-charging on Charger => nothing not even charging light
-plugged into (running) pc => nothing not even charging light
-5 hours in the fridge => nothing
-charging over night => nothing
Any hints ?
Thx for the goot work around here and greets from Germany !
Sebastian
PS If anyone got one to offer => contact me. Dont like those situations
Bad news!
Seems like your MB is gone...:crying:
Maybe one chance left for a JTAG attempt to a local service shop...
thats what i was afraid of
at least it happend only one hour after i made a backup
thx for the reply !

Categories

Resources