Database Users

CPUFreq Governor Info

A plethora of info on CPU governors (source):
CPU frequency and voltage scaling code in the Linux(TM) kernel
L i n u x C P U F r e q
C P U F r e q G o v e r n o r s
- information for users and developers -
Dominik Brodowski <[email protected]>
some additions and corrections by Nico Golde <[email protected]>
Clock scaling allows you to change the clock speed of the CPUs on the
fly. This is a nice method to save battery power, because the lower
the clock speed, the less power the CPU consumes.
Contents:
---------
1. What is a CPUFreq Governor?
2. Governors In the Linux Kernel
2.1 Performance
2.2 Powersave
2.3 Userspace
2.4 Ondemand
2.5 Conservative
2.6 Interactive
2.7 MinMax
2.8 SmartassV2
3. The Governor Interface in the CPUfreq Core
1. What Is A CPUFreq Governor?
==============================
Most cpufreq drivers (in fact, all except one, longrun) or even most
cpu frequency scaling algorithms only offer the CPU to be set to one
frequency. In order to offer dynamic frequency scaling, the cpufreq
core must be able to tell these drivers of a "target frequency". So
these specific drivers will be transformed to offer a "->target"
call instead of the existing "->setpolicy" call. For "longrun", all
stays the same, though.
How to decide what frequency within the CPUfreq policy should be used?
That's done using "cpufreq governors". Two are already in this patch
-- they're the already existing "powersave" and "performance" which
set the frequency statically to the lowest or highest frequency,
respectively. At least two more such governors will be ready for
addition in the near future, but likely many more as there are various
different theories and models about dynamic frequency scaling
around. Using such a generic interface as cpufreq offers to scaling
governors, these can be tested extensively, and the best one can be
selected for each specific use.
Basically, it's the following flow graph:
CPU can be set to switch independently | CPU can only be set
within specific "limits" | to specific frequencies
"CPUfreq policy"
consists of frequency limits (policy->{min,max})
and CPUfreq governor to be used
/ \
/ \
/ the cpufreq governor decides
/ (dynamically or statically)
/ what target_freq to set within
/ the limits of policy->{min,max}
/ \
/ \
Using the ->setpolicy call, Using the ->target call,
the limits and the the frequency closest
"policy" is set. to target_freq is set.
It is assured that it
is within policy->{min,max}
2. Governors In the Linux Kernel
================================
2.1 Performance
---------------
The CPUfreq governor "performance" sets the CPU statically to the
highest frequency within the borders of scaling_min_freq and
scaling_max_freq.
2.2 Powersave
-------------
The CPUfreq governor "powersave" sets the CPU statically to the
lowest frequency within the borders of scaling_min_freq and
scaling_max_freq.
2.3 Userspace
-------------
The CPUfreq governor "userspace" allows the user, or any userspace
program running with UID "root", to set the CPU to a specific frequency
by making a sysfs file "scaling_setspeed" available in the CPU-device
directory.
2.4 Ondemand
------------
The CPUfreq governor "ondemand" sets the CPU depending on the
current usage. To do this the CPU must have the capability to
switch the frequency very quickly. There are a number of sysfs file
accessible parameters:
sampling_rate: measured in uS (10^-6 seconds), this is how often you
want the kernel to look at the CPU usage and to make decisions on
what to do about the frequency. Typically this is set to values of
around '10000' or more.
show_sampling_rate_(min|max): the minimum and maximum sampling rates
available that you may set 'sampling_rate' to.
up_threshold: defines what the average CPU usage between the samplings
of 'sampling_rate' needs to be for the kernel to make a decision on
whether it should increase the frequency. For example when it is set
to its default value of '80' it means that between the checking
intervals the CPU needs to be on average more than 80% in use to then
decide that the CPU frequency needs to be increased.
ignore_nice_load: this parameter takes a value of '0' or '1'. When
set to '0' (its default), all processes are counted towards the
'cpu utilisation' value. When set to '1', the processes that are
run with a 'nice' value will not count (and thus be ignored) in the
overall usage calculation. This is useful if you are running a CPU
intensive calculation on your laptop that you do not care how long it
takes to complete as you can 'nice' it and prevent it from taking part
in the deciding process of whether to increase your CPU frequency.
2.5 Conservative
----------------
The CPUfreq governor "conservative", much like the "ondemand"
governor, sets the CPU depending on the current usage. It differs in
behaviour in that it gracefully increases and decreases the CPU speed
rather than jumping to max speed the moment there is any load on the
CPU. This behaviour more suitable in a battery powered environment.
The governor is tweaked in the same manner as the "ondemand" governor
through sysfs with the addition of:
freq_step: this describes what percentage steps the cpu freq should be
increased and decreased smoothly by. By default the cpu frequency will
increase in 5% chunks of your maximum cpu frequency. You can change this
value to anywhere between 0 and 100 where '0' will effectively lock your
CPU at a speed regardless of its load whilst '100' will, in theory, make
it behave identically to the "ondemand" governor.
down_threshold: same as the 'up_threshold' found for the "ondemand"
governor but for the opposite direction. For example when set to its
default value of '20' it means that if the CPU usage needs to be below
20% between samples to have the frequency decreased.
2.6 Interactive
---------------
The CPUfreq governor "interactive" is designed for latency-sensitive,
interactive workloads. This governor sets the CPU speed depending on
usage, similar to "ondemand" and "conservative" governors. However,
the governor is more aggressive about scaling the CPU speed up in
response to CPU-intensive activity.
Sampling the CPU load every X ms can lead to under-powering the CPU
for X ms, leading to dropped frames, stuttering UI, etc. Instead of
sampling the cpu at a specified rate, the interactive governor will
check whether to scale the cpu frequency up soon after coming out of
idle. When the cpu comes out of idle, a timer is configured to fire
within 1-2 ticks. If the cpu is very busy between exiting idle and
when the timer fires then we assume the cpu is underpowered and ramp
to MAX speed.
If the cpu was not sufficiently busy to immediately ramp to MAX speed,
then governor evaluates the cpu load since the last speed adjustment,
choosing th highest value between that longer-term load or the
short-term load since idle exit to determine the cpu speed to ramp to.
There is only one tuneable value for this governor:
min_sample_time: The minimum amount of time to spend at the current
frequency before ramping down. This is to ensure that the governor has
seen enough historic cpu load data to determine the appropriate
workload. Default is 80000 uS.
2.7 MinMax
---------------
The CPUfreq governor "maxmin" tries to minimize the frequency jumps by limiting
the selected frequencies to only two frequencies: either the min or the max
frequency of the current policy. The frequency is raised or lowered according
to the current load and the 'up_threshold' and 'down_threshold'.
Its parameters and implementation are similar to that of conservative.
It does not have the freq_step parameter as it jumps right from min to max
and vice-versa.
The sampling_down_factor, unlike conservative, will count the minimal number
of samplings since the last time we saw the 'up_threshold' load on the CPU.
Hence it is set to higher default and acts as a limiter not to do too many
frequency jumps without hurting the performance.
2.8 SmartassV2
---------------
The CPUfreq governor "smartassV2", like other governors, aims to balance
performance vs battery life by using low frequencies when load is low and
ramping the frequency when necessary, fast enough to ensure responsiveness.
The implementation of the governor is roughtly based on the idea of interactive.
The idle loop is used to track when the CPU has idle cycles. The idle loop will
set a relatively high rate timer to sample the load when appropriate, the timer
will measure the load since it was set and schedule a work queue task to do the
actual frequency change when necessary.
The most important tunable is the "ideal" frequency: this governor will aim
for this frequency, in the sense that it will ramp towards this frequency much
more aggresively than beyond it - both when ramping up from below this frequency
and when ramping down from above this frequency. Still, note, that when load is
low enough the governor should choose the lowest available frequency regardless
of the ideal frequency and similarly when load is consistently high enough the
highest available frequency will be used.
Smartass also tracks the state of the screen, and when screen is off (a.k.a
sleep or suspended in the terms of this governor) a different ideal frequency
is used. This is the only difference between the screen on and screen off
states. Proper tuning of the awake_ideal_freq and sleep_ideal_freq should
allow both high responsiveness when screen is on and utilizing the low
frequency range when load is low, especially when screen is off.
Finally, smartass is a highly customizable governor with almost everything
tweakable through the sysfs. For a detailed explaination of each tunable,
please see the inline comments at the begging of the code (smartass2.c).
Click to expand...
Click to collapse

Kernel][ICS] Devil3_1.1.0 [02/08/12] - Cappy

This kernel is based on teamhacksung's kernel, with updated Linux base to 3.0.38
This kernel is working with every ICS based Rom
Features:
- 378, 391 and 403 Mb Ram available (selectable in kernel, no need for a patch (403 mb breaks 720p) only reboot required)
- 2 different recoveries included (cmw touch recovery + twrp recovery (to use TWRP, just create a file named "twrp" at /cache))
- SIO scheduler (default)
- V(R) scheduler (maybe even faster than SIO, can be set as default by using NSTools for example)
- init.d
- Voodoo Sound and CM9 Color Adjusment / Voodoo Color (VC version)
- Devil Idle
- BLN V9 (thx to mialwe)
- USB Host mode driver (for more information about this, and for saying thanks to the guy, who ported this for our phone, please visit this thread: http://forum.xda-developers.com/showthread.php?t=1450298 )
-Ezekeel's Live_Oc
- Ezekeel's Deep Idle V2
- Touchwake
- vibrator intensity control (by mialwe)
- BLX (Batterie Life Extender, I don't think we need it, but maybe one feels better by using it )
- backports from Linux 3.2 and 3.3
- Swap/Zram support
- Zcache, Cleancache and Frontswap
- Uksm
- Fiops io scheduler
- Smooth_ui included to ondemand, conservative, smartass, lulzactive, lagfree and lazy governor (only one setting for activating/deactivating it in general)
- 3 cpu governor presets (smooth, normal, powersave) for ondemand, conservative, smartass, lulzactive, lagfree (only one setting for switching the mode in general)
- many other small features and improvements
Donwload and Changelog post 2
FAQ and known issues in post 3
Click to expand...
Click to collapse
Many of the features (like Live_OC) require NSTools, which can be found at market for free.
NEW:
Devil kernel Config: http://forum.xda-developers.com/showthread.php?t=1715383
Devil Kernel Manager: http://forum.xda-developers.com/showthread.php?t=1723222
Both Apps are really great. Please try on your own, which one you like more.
you still can use the previous methods of setting up the kernel:
Please also try this app http://forum.xda-developers.com/showthread.php?p=22430406, for setting many of the options which are only available with my kernel.
a pre configured file for use with command center can be found here: http://forum.xda-developers.com/showpost.php?p=27353078&postcount=240 (you have to remove .zip extension)
a good explination/example of how to use it, can be found here: http://forum.xda-developers.com/showpost.php?p=26301176&postcount=4842
if you don't like additional apps (or are having problems with command center), i recommend using this init.d script: http://forum.xda-developers.com/showpost.php?p=26683004&postcount=5346
Click to expand...
Click to collapse
Kernels with VC in the name are coming with Voodoo Color
oliva94 said:
IF the kernel zip name contains _JB_, THEN and only then you can use it IF you do NOT have datadata partition
ELSE if you HAVE datadata, then use one WITHOUT _JB_ in the name
if you use it otherwise, it will boot but system is eventually going to crash/not load due to partition table (thus blockdevice naming) mismach
Click to expand...
Click to collapse
Many Thanks to:
Teamhacksung
Zacharias.maladroit
Onecosmic
ytt3r
TK Glitch
Ezekeel
Eugene373
franciscofranco
Sunra
scheichuwe
perka
sztupy, for his great work, to get usb host mode driver
mialwe
stratosk
F4k for the idea to flash bigmem libs
...
sources:
https://github.com/DerTeufel
Click to expand...
Click to collapse
This kernel is also available for:
Captivate, Fascinate and Vibrant
Click to expand...
Click to collapse
Working on this kernel is taking many hours almost every day. With a small donation, you show me, that my work is appreciated by you.
If you like this kernel, please donate to me

Changelog:
changelog 02.08.2012:
- bug fix to bln, to prevent kernel panic in some situations (thx to thalamus)
- switched from deep_idle 2 to idle2 (also thx to thalamus)
- updated kernel to linux 3.0.38
- dockaudio sysfs for captivate and fascinate
- automated symlinking from data to system: if one wants to free up some space at /system, without removing an app completely, just copy it from /system/app to /data/sys-parts/app (create the folder if not there), and reboot. during reboot, the app from system gets deleted, and the app from /data/sys-parts/app gets symlinked to system. this is working for almost every app, but i don't recommend doing this with apps, needed for android to work (framework, media provider, settings,...)
IDLE2 can be enabled with the following command:
echo 0 > /sys/module/cpuidle/parameters/idle2_disabled
IDLE2 can be disabled with the following command:
echo 1 > /sys/module/cpuidle/parameters/idle2_disabled
Stats can be obtained from the standard cpuidle interface, which, for
IDLE2 is located at:
/sys/devices/system/cpu/cpu0/cpuidle/state*/time
where * = 1, 2, 3
changelog 25.07.2012:
- updated recovery (no "sdcard format"-bug anymore, external sd card is named correctly)
- vibrant: hopefully fixed froyo ril
- jellybean: galaxy s settings working now
changelog 22.07.2012:
This kernel is for use with ICS only, if you are looking for a kernel, running on teamhacksung cm10 build, visit my jellybean kernel thread[/url]
- updated kernal base to linux 3.0.36
- updated "block" to linux 3.3
- readded fiops io scheduler (kept cfq this time)
- updated cwm recovery to 6.0.1.0 (please create a new nandroid, because of possible incompatibilities between old/new recovery)
- compiled with linaro toolchain (gcc 4.7.1) and O3 compiler flags
- made uksm scan less often (save cpu time and power)
- at first boot: only delte init.d scripts created by other kernels
- increased usb write performance
- lowered ram and display voltages a little bit
- fixed some bugs related to devil settings (they should stick now after reboot, if set by one of the devil apps)
- support for scripts in /system/etc/shutdown.d (thx to Efpophis)
all scripts placed at /data/local/shutdown.d or /system/etc/shutdown.d get executed at shutdown/reboot
you can use this, to play a shutdown sound for example.
by default 00shutdown gets created, which plays a music file, when it is placed at one of these folders/places
/system/media/audio/ui/shutdown.ogg
/data/media/audio/ui/shutdown.ogg
Click to expand...
Click to collapse
- disabled some debugging options
- audio (and for fascinate: camera fixes) by Efpophis+
- patch for improving batterie life by CML
- nfts read/write driver built in (for use with usb host mode)
- reverted refreshrate_mod and gpu_oc mod, as both weren't working
changelog 18.06.2012:
- some changes to load balancing
- added ultra ksm (metioned by zach thx for this my friend)
- readded fiops io scheduler (still experimental and could cause instablilities)
- using snappy compression for zram now (2 times faster, but only 2% less compression)
- added the possibility to change zram size (at /data/local/devil/zram_size, with valid values: 50, 75, 100 and 150 (all in mb))
- fixed the applying of user_min/max freq after reboot
- vibrant: fixed gps
- fascinate: fixed nandroid in cwm recovery
what is ksm? http://en.wikipedia.org/wiki/Kernel_SamePage_Merging_(KSM)
uksm is more optimized and also working for single core systems. using this should give much better ram usage, but at the cost of more cpu usage
############# most probably not working (yet)##############
i have added seperate gpu oc from jt1134's galaxy_tab (to switch between 200 and 250 mhz), but i did not get any improvements in antutu...further tests needed
echo 1 > /sys/kernel/pvr_oc/pvr_oc (for 250 mhz)
echo 0 > /sys/kernel/pvr_oc/pvr_oc (for 200 mhz), no reboot needed
and also have changend default screen refreshrate from 60 to 56, with the possibility to change it:
echo 1 > /sys/kernel/refreshrate/enable (60 hz)
echo 0 > /sys/kernel/refreshrate/enable (56 hz)
######################################################
changelog 10.06.2012:
cwm recovery:
- fixed mounting of external sd card to pc
kernel:
- picked two commits from linux 3.0.32 (avoid a possible memory leak, small fix to ext4 driver)
fascinate:
- fixed wrong mount points
changelog 09.06.2012:
- updated Zram and Zcache from linux 3.3
- updated android binder driver from linux 3.3
- fixed restoring of backups within TWRP recovery
- added virtual buttons to cwm recovery (Attention: they still don't work!)
- call vol hack from tk glitch (take a look at init.d folder and edit the script to make changes to call vol hack)
- bigmem values get applied at first boot after power on (if there is a value at /data/local/devil/bigmem, 1 for 391 mb and 2 for 403 mb (the last one breaks 720p)
- prevent phantom key presses (from tk glitch)
changelog 24.05.2012:
- Smooth_ui included to ondemand, conservative, smartass, lulzactive, lagfree and lazy governor (only one setting for activating/deactivating it in general)
- 3 cpu governor presets (smooth, normal, powersave) for ondemand, conservative, smartass, lulzactive, lagfree (only one setting for switching the mode in general)
- no need for activating/deactivating of selective live_oc anymore --> just change target low and target high
- BLX back in
- fixes to devil idle to be more stable while in call
- 1,5 mb more ram (thanks to mialwe)
- added aroma filemanager to cwm recovery
- added fully working TWRP recovery optional to cwm recovery (to use TWRP, just create a file named "twrp" at /cache)
- added option to select ram config in kernel --> no need for flashing an other kernel to get more ram (thanks to stratosk)
- switched to new initramfs from stratosk and mialwe ( now there will be cmw zip and odin tar file of every kernel version)
- added possibility to use Zram instead of Swap
- no need for flashing/using special scripts to make swap/zram working anymore
- added zcache
- added frontpage
- added cleancache
- added fudgeswap (thanks to ezterry and faux123)
changelog 01.05.2012:
- all changes from cm9 stock kernel (including mount points option)
- some fine tuning to deadline and sio
- Devil Idle: limiting bus/ram/gpu speed to 100 mhz for 100-800 mhz cpu freq, while screen off (automatic mode) or always (permanet), both modes automatically reduce the int voltages of the affected freq by 50 mV
- compiled with swap support
- added stratosk's smooth_ui to lulzactive governor (activated by default)
- rest oc_value to 100 while screen off, and back when screen turns on (combined with devil idle automatic, can't be turn on/off without devil idle)
- added posibility for different voltages while screen off (also bundled with devil_idle, with default settings, stock arm voltages are applied, because of live_oc set to 100)
- added the possibility to set freq limits while screen off (min and max freq)
19.04.2012
- even better fix to selective live_oc (last one (in test kernel) generated some overhead)
- fixed sampling rate of ondemand and conservative (have ported mialwe's/stratosk's sleep multipliers)
- new tunables for ondemand and conservativ
sleep multiplier and tunables:
mialwe and stratosk had the great idea, to change the sampling rate of conservative and ondemand governor while display of. for this, he introduced the sleepmultiplier (in his case factor 3). this means, if you set sampling rate to 20000, it changes to 60000 while screen off, and back, when screen on.
for ondemand and conservative:
i have made this multipliers tunable. proper values are between 1 and 5, because one could want a higher multiplier while screen off, if sampling rate is very low while screen on (higher sampling rate means, less checking for work load --> better batterie, worse performance). with this tunables you get better batterie, without making the performance worse while screen on.
two other tunables: up_threshold_min_freq and responsiveness_freq
the first one is a very low threshold while on low freq (by default 40), to make the governor scale up faster, until the responsiveness_freq is reached.
the responsiveness_freq is set to 400000 (400 mhz) by default. while the freq is below this value, up_threshold is the same as up_threshold_min_freq, and freq jumps to responsiveness_freq, with skipping the freq between the actual one and the responsiveness_freq. (conservative governor does not jump up to this step)
responsiveness_freq can be set to values between 100000 and 1400000
up_threshold_min_freq can be set to the same values as the normal up_threshold.
not tunable: while screen off, up_threshold is set to 95, no matter your other settings, to save more batterie.
up_threshold_min_freq is disbaled by default for conservative governor
for lulzactive:
for this governor, i did similar things, but they are not tunable till now.
when screen off:
- inc_cpu_load is set to 90, and back to the original value, when screen turns on
- up_sample_time is set to 50000, and back to the original value, when screen turns on
- down_sample_time is set to 40000, and back to the original value, when screen turns on
other changes:
- fix to touchwake from ezekeel, and another fix from stratosk
- upstream fix to compass
- building for i9000B now, too (big thanks to F4k for the hints by pn )
- removed some typos from recovery
- removed some annoying "no's" and "yes" from recovery in misc menu
- fixed wifi mode switch (pm_fast is the one with better signal)
14.04.2012:
- new b versions (only stock ram) changend to 377 mb, VC version needs the 720p fix from my ftp server. cmc version already patched
13.04.2012:
- updated wifi driver
- added the possibility to switch between wifi PM_Fast and PM_Max mode (Pm_Fast = better signal, PM_Max = better batterie, default is PM_Max)
- user interface to disable fsync (this gives more performace, at the risk of data loss on a crash, taken from ezekeel, so it should be ok ), default is off, to be safe
- fixed voodoo color kernels (these have the VC in their names)
10.04.2012:
- added vibrator intensity control (by mialwe), presets can be changend in recovery
- stock ram version now available (348 mb ram), XL (390 mb), XL_bm (402 mb)
- removed 1080 mhz freq for now
- small correction to touchwake
- small correction to selective live_oc (now the low freq really are not live_oc'ed)
05.04.2012:
- fixed bug in selective live_oc, which caused the target high not taking affect to the highest freq, if highest freq equals target high
- fixed another bug in selective live_oc, which could lead to gpu crashes due to overclocking the ram, but not the cpu freq (for low steps)
- added a switch to change between "normal" and selective live_oc
by changing the live_oc mode while using it, live_oc value is set back to 100, to prevent strange things
- added possibility to set max. freq for boot (in recovery). This freq is set until init.d is executeted (it is automatically set to 1000 at this point, to make sure there are no conflicts with other cpu settings from users)
#Already in the last version, but i forgot about it:
- deep idle fixes from stratosk (many thanks)
- added possibility to underclock by using live_oc (limit is 90 now, which means lowering all freq and bus speed by 10%, to save more batterie when really needed)
03.04.2012:
For now there are three different RAM versions:
- stock mem kernel has 379 mb ram, everything working
- "slim ics" (XL) kernel comes with 390 mb, this is breaking playback of some high resolution videos
- XL_BM is coming with 402 mb ram, but breaking 720p
(while flashing the kernel, the modded rom files are also flashed, so you don't need to flash a new rom to get 379 or 390 mb)
-added new frequency: 1080 mhz (1100 does not like live_oc)
- fixed SmartassV2 for live_oc (after changing live_oc value, you have to change the smartass values, too, but then they automatically apply to the live_oc value (although you can only select 800 mhz in nstools (for example))
- touch recovery with custom devil menu (for some reason it takes a few seconds to load the first time, missing virtual keys is a warning, because there are no virtual keys yet)
-fast charge (thx to chad0989 for this), disabled by default.
you also can use the widget from chad (to place on homescreen) to toggle the fast_charge mode
https://play.google.com/store/apps/d...stchargewidget
Click to expand...
Click to collapse
while fast charge is activated you cannot connect as usb device
- added datafix script to init.d (this script is deactivated by deafult. to make it work, you have to creat a file named datafix and placed in /data/local/)
- reworking and cleaning many parts to get more ram, speed, and stability
05.03.2012:
- updated sio i/o scheduler to latest version
- small updates to ondemand and conservative governor from linux 3.2
- bettter performance for CFS kernel due to tuning and patches
- tuning to deadline scheduler
- better i/o performance
- changed bootlogo (probably not the last time )
28.02.2012
- finally working bln V9 (no need for LED2 anymore)
- fixed lockscreen freezes
- reverted memory tweaks, which could be the reason for lagging after using a day
- again wlan fixes from tk-glitch
- tweaked conservative and ondemand governor (conservative still is not too aggressive)
- added dm-cache again (who has removed this from my github? )
- improve usb signal quality
- xcaliburinhand's dock audio support (untested, do not have a dock)
- less debugging
- fixed kernel version not displayed under "about phone"
12.02.2012
- Added newest Fiops scheduler (tuned for more performance)
- When Gpu is active, min CPU freq is set to second lowest step
- fixes to live_oc and custom voltage
- default mount parameter NOATIME and NODIRATIME (faster)
- updated Wifi drivers (thanks to tk-glitch)
- tuned intellidemand for better performance
- removed some stuff (zram, swap, tweaks to cpufreq untill I know what was causing the instabilities of last build)
05.02.2012
- added Touchwake
- added BLX
- upgraded BLN from V8 to V9 (working for missed calls, blinking or static light, configurabel by using NSTools or BLN Pro App)
- added Intellidemand governor
- added mdnie settings to voodoo color version
- readded deep idle v2 again (I think it is the best/only working one, although
- version with CFS (instead of BFS) now also available (maybe better multitasking and batterie life, but slower)
- removed BFQ I/O Scheduler
- tons of smaller fixes and improvements
30.01.2012
-revert: Voodoo Sound now to be set with DSP Manager
29.01.2012
- Linux kernel 3.1.10
- Deep Idle from Eugene373 (always enabled, no stats)
- added BFQ v 3.1 I/O Scheduler
- Voodoo Sound now to be set with DSP Manager
- Zram (can be disabled by removing Zram file from init.d)
- Zcache and Cleancache (not working yet?)
- optimized rwsem algorithm
- USB Host V5
24.01.2012
- init.d support (the folder is not created by the kernel. You have to do it for yourself)
- Deep Idle V2 back in
- new Cpu governors: MinMax, Lagfree, Lulzactiv
- LED V2 (you can set blinking by using nstools, also working for missed calls in most cases (sometimes it is not working for missed calls, don't know why at the moment))
- Backlight Dimmer (only LED version): used to turn led backlight of, while screen is on, after defined period of time. Deactivating it, makes your backlight stay on all the time
- I/O-less dirty throttling completely backported from kernel 3.2
- Ext4 with 3.2 patches
- Proportional Rate Reduction for TCP - by Google
- USB Host V 4
19.01.2012
- Usb Host drivers integrated
- Cm9 Color adjustment
- Removed Deep Idle because of Bluetooth problems (hopefully it will come back, still testing)
16.01.2012:
- Updated Kernel basis to Linux 3.1.9
15.01.2012:
- fixed bug in cpu spy, caused by live_oc
- still using voodoo color for now, maybe two additional kernel versions tomorrow
Click to expand...
Click to collapse
files with .zip have to be flashed within recovery (twrp or cwm)
files with .tar can be flashed by using odin or heimdall (they are placed at the end of post 3)
ICS:
http://rootaxbox.no-ip.org/divers/ICS/ many thanks to Rootax
JellyBean (with default cm10 partition layout for use with teamhacksung's rom):
http://rootaxbox.no-ip.org/divers/jellybean/
http://devil.haxer.org/ many thanks to SysTem-X (not updatet yet)

Known issues:
- virtual buttons in cwm recovery not working
cappy specific:
- deep idle is causing some devices to not wake up again --> need to long press power button
Click to expand...
Click to collapse
How to:
you can change ram setting by doing the following ( to make these settings even stick after power off, you also have to echo the same value to to /data/local/devil/bigmem):
echo 1 > /sys/kernel/bigmem/enable (this gives you xl mem of 391 mb)
echo 2 > /sys/kernel/bigmem/enable (this gives you bm mem of 403 mb (this is breaking 720p))
echo 0 > /sys/kernel/bigmem/enable (this gives you cm9 default mem of 378 mb)
you have to reboot to make changes work
Click to expand...
Click to collapse
With setting this, your desired swap mode gets automatically applied at boot time. For swap, you have to create a swap partition at your external sd card before
echo 1 > /data/local/swap_use (for using swap partition on external sd card, you have to create this partition before)
echo 2 > /data/local/swap_use (for using Zram, no other modifications required)
you have to reboot to make changes active. You can't use swap and Zram at the same time
Click to expand...
Click to collapse
These are the settings for devil idle:
activate automatic:
echo 1 > /sys/devices/virtual/misc/devil_idle/bus_limit
permanent on:
echo 2 > /sys/devices/virtual/misc/devil_idle/bus_limit
deactivate
echo 0 > /sys/devices/virtual/misc/devil_idle/bus_limit_automatic
Click to expand...
Click to collapse
to set different voltages while screen off (this only is working, if devil idle automatic mode is activated)
this is an example, how to apply screen_off arm voltages:
echo 1450 1400 1350 1275 1075 975 875 800 > /sys/class/misc/customvoltage/arm_volt_screenoff
this way, it is possible to undervolt while screen off, but overvolt and overclock while screen on
for now, the int voltages can not be changend
Click to expand...
Click to collapse
set freq limits while screen off (min and max freq)
enable the limits:
echo 1 > /sys/devices/virtual/misc/devil_idle/user_min_max_enable
disable:
echo 0 > /sys/devices/virtual/misc/devil_idle/user_min_max_enable
set values to be applied if activated:
echo 100000 > /sys/devices/virtual/misc/devil_idle/user_min
echo 800000 > /sys/devices/virtual/misc/devil_idle/user_max
both are independent from devil_idle, and get applied when screen turns off
by default 100 and 1000 mhz are set.
values which can be put here are all "stock" freq (without live_oc level) multiplied with 1000. live_oc values get applied automatically.
Click to expand...
Click to collapse
to set responsiveness_freq, up_threshold_min_freq or sleep_multiplier for ondemand and/or conservative governor, you have to do it like this:
echo VALUE > /sys/devices/system/cpu/cpufreq/ondemand/VARIABLE_NAME
and
echo VALUE > /sys/devices/system/cpu/cpufreq/conservative/VARIABLE_NAME
example:
echo 400000 > /sys/devices/system/cpu/cpufreq/ondemand/responsiveness_freq
echo 50 > /sys/devices/system/cpu/cpufreq/ondemand/up_threshold_min_freq
echo 5 > /sys/devices/system/cpu/cpufreq/ondemand/sleep_multiplier
up_threshold_min_freq is disbaled by default for conservative governor
(to disable it for ondemand you have to set up_threshold_min_freq to 100.
Click to expand...
Click to collapse
switch between wifi PM_Fast and PM_Max mode (Pm_Fast = better signal, PM_Max = better batterie, default is PM_Max)
echo 1 > sys/module/bcmdhd/parameters/uiFastWifi (pm_fast)
echo 0 > sys/module/bcmdhd/parameters/uiFastWifi (pm_max)
Click to expand...
Click to collapse
user interface to disable fsync (this gives more performace, at the risk of data loss on a crash, taken from ezekeel), default is on, to be safe
echo 1 > /sys/devices/virtual/misc/fsynccontrol/fsync_enabled (fsync enabled)
echo 0 > /sys/devices/virtual/misc/fsynccontrol/fsync_enabled (fsync disabled)
Click to expand...
Click to collapse
to set the values for vibrator intensity:
echo value > /sys/class/timed_output/vibrator/duty (where value is between 20000 and 43640)
if you want the changes to be applied at boot, you have to use one of the presets from recovery, use an init.d script, or:
echo value > /etc/devil/vibrator (where value is between 20000 and 43640)
Click to expand...
Click to collapse
activate fast charge: echo 1 > /sys/kernel/fast_charge/force_fast_charge
Click to expand...
Click to collapse
deactivate fast charge
echo 0 > /sys/kernel/fast_charge/force_fast_charge
you also can use the widget from chad (to place on homescreen) to toggle the fast_charge mode
https://play.google.com/store/apps/d...stchargewidget
Click to expand...
Click to collapse
while fast charge is activated you cannot connect as usb device
Click to expand...
Click to collapse
Questions and Answers:
Q: What the hell are all these governors?
A: here you should find the answer: http://forum.xda-developers.com/showthread.php?p=19846297
Q: What's a good setup for live_oc??
A: No one knows. Every phone is different. It seems like the folling setup is running well for some (many?) users. If you get reboots with it, you have to find the setup for yourself.
if you are satisfied with this configuration, please hit the thanks button of Crack: http://forum.xda-developers.com/showpost.php?p=22194160&postcount=1246
.:Crack:. said:
OK, these are mine. Rock stable
LiveOC 117% -> 1200 MHz -> 1404 MHz
Freq/ARM/Init
1200/1400/1150
1000/1325/1125
800/1250/1125
400/1025/1100
200/900/1100
100/875/1000
low freqs could possibly be tweaked harder but stability was my fist goal
Click to expand...
Click to collapse
Q: How can I set up swap?
A: Take a look at this thread: http://forum.xda-developers.com/showthread.php?t=1610835, and especially at this post:
http://forum.xda-developers.com/showpost.php?p=25578231&postcount=83
Q: What is Touchwake? Can you explain it?
A: With Touchwake, the touchscreen still recognices your fingers, after turning off (for a predefined time (NSTools)). For a detailed explenation, take a look at Ezekeel's thread: http://forum.xda-developers.com/showthread.php?t=1239240
Q: How can I make Voodo Color settings been saved after reboot?
A: You have to use Voodoo Pro App, because of changes between Gingerbread and ICS, and only the Pro app is updated till now.
Q: Which is the best IO Scheduler?
A: I think SIO and V(R) are the fastest.
Q: How can I enable DeepIdle/Live_Oc?
A: You have to use NSTools. You find it on market. It's free.
Deep Idle Questions:
Q: How can I activate the deep idle stats?
echo 1 > /sys/class/misc/deepidle/stats_enabled
Q: What's the meaning of TOP=Off and TOP=On when I look at the Deep Idle status?
A: When TOP=Off is used, the best powersaving state is used. TOP=ON will be shown, when bluetooth or gps are running.
Q: In Idle status I only see TOP=On. What's wrong here? I don't use Bluetooth or Gps.
A: You have to flash the modded framework-res.apk, because ICS does not fully deactivate bluetooth by default. Even if you never use it.
Q: Idle Stats only are showing Idle, but no Deep Idle. Why?
A: An App is preventing the use of Deep Idle. At first, you should try closing the cam, running in the background. Also rebooting should solve this problem.
Q: What is fudgeswap?
A:
Setting this to a very large positive number will indicate swap ought
to be fully used as free (and will slow the system down)
smaller numbers will allow you to put some pressure on SWAP without
slowing the system down as much.
small negitive numbers will allow the system to be faster at the same
minfree level.
default is 512 to give a very little bit of pressure to use some swap
but this can be modified at runtime via:
/sys/module/lowmemorykiller/parameters/fudgeswap

Very nice, was looking forward to this! Thanks (;
Sent from my ICS Cappy

This looks very promising, going to be keeping an eye on it for sure.
Herp derp Captivate XDA Premium App.

I've been waiting for this for so long. Thank you

I really hope, that everything is working, especially the touchkeys...
Then I can start to add more, in about 6 hours.
Gesendet von meinem GT-I9000 mit Tapatalk 2

I've been waiting to see this in the Captivate Forum

thanks for the new kernel any chance you can write up a post about what each of the tweaks do im still trying to wrap my head around all the terms here lol

Nice to have another kernel around. What is the highest OC on it?

shaolin95 said:
Nice to have another kernel around. What is the highest OC on it?
Click to expand...
Click to collapse
1,4GHZ is the max step you can choose
Kernel runs smooth, games run very well at 1,1GHZ Step with 110%LiveOC SmartassV2 and Deadline
Touchkeys are working fine too
Edit:
The min min step is 200mhz
cant change it to 100

kevinnol said:
1,4GHZ is the max step you can choose
Click to expand...
Click to collapse
That, and there's also selective LiveOC so you can probably max out your phone's capabilities. I haven't flashed yet, just going off of the OP.
Herp derp Captivate XDA Premium App.

I will give it a shot..is not a big deal to test it

Hey DerTeufel1980, you make me wait so long

kevinnol said:
1,4GHZ is the max step you can choose
Kernel runs smooth, games run very well at 1,1GHZ Step with 110%LiveOC SmartassV2 and Deadline
Touchkeys are working fine too
Edit:
The min min step is 200mhz
cant change it to 100
Click to expand...
Click to collapse
this is because of the min freq is set to 200, while the gpu is active...in most cases, this is, when your screen is on
please check cpu spy stats, to see, that 100 mhz also is used.
but, i am going to remove it, cause everyone can set 200 mhz as min, if he/she likes to.

In the Recovery are 3 different profiles, when i choose as example smooth profile what changes are made ?
Looked into the i9000 thread but cant find the answer

Testing
Testing with Doc's Master V11. So far, so good!
Thanks for your hard work!

kevinnol said:
In the Recovery are 3 different profiles, when i choose as example smooth profile what changes are made ?
Looked into the i9000 thread but cant find the answer
Click to expand...
Click to collapse
when you choose smooth, almost each governor is using more agressive profiles for better performance. if you choose powersave, the same, but more power, and with normal, the default governor settings are applied
it's for those of you, who don't want to search and try own settings (or at least, to get an idea, how to change some things)

Testing this out with my previous settings from Glitch, so far so good at 117% LiveOC on 1GHz step.
Herp derp Captivate XDA Premium App.

Will this kernel support call recording from the line? Many people missed that feature from old android 2.2.1

Slow phone after screen turn on and lockscreen (CyanogenMod 7.2 + sd-ext)

Hello everybody!
I'm having a strange problem: if i have the phone locked, with screen turned off for a while, in my pocket, when i turn it on again it is very slow. It takes about 30 seconds to come back to usual performance.
For example, if i unlock the phone and i go to SMS or WhatsApp, the keyboard (Swiftkey) it's so slow that i have to wait for every word to complete, before i can type another one.
After 30 seconds from the unlock the phone works ok.
The problem started when i've upgraded from CyanogenMod 7.1 to CyanogenMod 7.2 and i've created an sd-ext partition (in ext3 format, on a class 6 SD) to move there some apps.
I've got an HTC Desire HD.
I noticed the same problem when i was using a MIUI rom with the CPU Tuner app: i supposed that it slowed down too much the CPU when the screen was locked, so that it took a lot to come back to normal performances. But, now, i don't have that app installed and, looking ad Exaile 2 when i unlock my phone, it seems that CPU frequencies it's a 1 Ghz and even RAM usage is ok.
What could it be?
I have to wipe and install CM 7.2 from scratch?
Or could it be the sd-ext partition with apps on?
Thank you in advance!

Try installing set CPU or CPU Tuner again and set the CPU to something high when the phone is asleep. If that then works and it is no longer laggy try reverting it to a lower speed.

Not sure about the sd ext partition,, but yes, try a full wipe and install 7.2.
Sent from a dream.

Just change the governor. Governor is interactive by default i think.
Had the same problem after weeks i just changed governor to ondemand and everything was prefect.
Sent from my Desire HD using Tapatalk 2

Try installing set CPU or CPU Tuner again and set the CPU to something high when the phone is asleep. If that then works and it is no longer laggy try reverting it to a lower speed.
Click to expand...
Click to collapse
When i had it, i never configured because i am too lazy
I'll give a try, thanks!
Not sure about the sd ext partition,, but yes, try a full wipe and install 7.2.
Click to expand...
Click to collapse
I do not really want to, but i think too that could be a good test
Just change the governor. Governor is interactive by default i think.
Had the same problem after weeks i just changed governor to ondemand and everything was prefect.
Click to expand...
Click to collapse
Good tip!
My governor is "interactive" too, infact. I'm changin it to "ondemand".
Does anyone have a table that explain the difference between governors?

I'm on ARHD and the same started all of a dudden a few months ago. I had the same governor and settings for months without change and this still started. I changed governors (ondemand, smoothass, smartass, etc.) but it still happens sometimes. Not ver often but sometimes.

sberla54 said:
Good tip!
My governor is "interactive" too, infact. I'm changin it to "ondemand".
Does anyone have a table that explain the difference between governors?
Click to expand...
Click to collapse
Here you go
7. CPU Scaling Governors
CPU governors control exactly how the CPU scales between your “max” and “min” set frequencies. Most kernels have “ondemand” and “performance.” The availability
ondemand – Available in most kernels, and the default governor in most kernels. When the CPU load reaches a certain point (see “up threshold” in Advanced Settings), ondemand will rapidly scale the CPU up to meet demand, then gradually scale the CPU down when it isn't needed.
interactive – Available in newer kernels, and becoming the default scaling option in some official Android kernels. The interactive governor is functionally similar to the ondemand governor with an even greater focus on responsiveness.
conservative – Available in some kernels. It is similar to the ondemand governor, but will scale the CPU up more gradually to better fit demand. Conservative provides a less responsive experience than ondemand, but can save battery.
performance – Available in most kernels. It will keep the CPU running at the “max” set value at all times. This is a bit more efficient than simply setting “max” and “min” to the same value and using ondemand because the system will not waste resources scanning for CPU load.
powersave – Available in some kernels. It will keep the CPU running at the “min” set value at all times.
userspace – A method for controlling the CPU speed that isn't currently used by SetCPU. For best results, do not use the userspace governor.
smartass – Included in some custom kernels. The smartass governor effectively gives the phone an automatic Screen Off profile, keeping speeds at a minimum when the phone is idle.
Click to expand...
Click to collapse
Here as well
CPUFreq governors in the Android Kernel
=======================================
+ performance
The CPUfreq governor "performance" sets the CPU statically to the highest frequency within the borders of scaling_min_freq and scaling_max_freq.
+ powersave
The CPUfreq governor "powersave" sets the CPU statically to the lowest frequency within the borders of scaling_min_freq and scaling_max_freq.
+ userspace
The CPUfreq governor "userspace" allows the user, or any userspace program running with UID "root", to set the CPU to a specific frequency by making a sysfs file "scaling_setspeed" available in the CPU-device directory.
+ ondemand
The CPUfreq governor "ondemand" sets the CPU depending on the current usage. To do this the CPU must have the capability to switch the frequency very quickly. There are a number of sysfs file accessible parameters: sampling_rate, show_sampling_rate_min, up_threshold, ignore_nice_load, sampling_down_factor.
+ conservative
The CPUfreq governor "conservative", much like the "ondemand" governor, sets the CPU depending on the current usage. It differs in behaviour in that it gracefully increases and decreases the CPU speed rather than jumping to max speed the moment there is any load on the CPU. This behaviour more suitable in a battery powered environment. The governor is tweaked in the same manner as the "ondemand" governor through sysfs with the addition of: freq_step & down_threshold
+ interactive
The CPUfreq governor "interactive" is designed for latency-sensitive, interactive workloads. This governor sets the CPU speed depending on usage, similar to "ondemand" and "conservative" governors. However, the governor is more aggressive about scaling the CPU speed up in response to CPU-intensive activity. The tuneable value for this governor are: min_sample_time & go_maxspeed_load
+ smartass (By [email protected])
The smartass governor is a complete rewrite of the interactive governor. CPU spends much more time at the lower frequencies for improved battery life. It gives the phone an automatic Screen Off profile, keeping speeds at a minimum when the phone is idle.
+ savagedzen (By [email protected])
SavagedZen is a governor based on the Smartass governor. With tweaks to paramaters which control how much and how fast cpu ramps up/down. Main difference versus Smartass is that cpu ramps down not in fixed steps, but based on cpu load heuristics, i.e. when cpu load falls below threshold (min_cpu_load), cpu immediately ramps down to a frequency derived from the measured load.
+ interactiveX (By [email protected])
Modified version of interactive with suspend code which locks at lowest clock speed when screen is off. Has a sleep+awake profile, meaning you don't need to set up manual profiles, it will lock at your minimum frequency during screen off
Click to expand...
Click to collapse

andreasy said:
I'm on ARHD and the same started all of a dudden a few months ago. I had the same governor and settings for months without change and this still started. I changed governors (ondemand, smoothass, smartass, etc.) but it still happens sometimes. Not ver often but sometimes.
Click to expand...
Click to collapse
Me too i didn't changed the governor, but in my case, a ROM upgrade and a sd-ext creation are some major changes that can affect performances...
l33ch0r said:
Here you go
Here as well
Click to expand...
Click to collapse
Thank you l33ch0r!
There doesn't seem to be much difference between "ondemand" and "interactive"; regarding to this documentation, "interactive" seems more quick.
Anyway, i've changed my governor to "ondemand" and i must say that all yesterday the phone has been fast and responsive. I'll keep you updated!
Thank you very much!

[GUIDE][NOOB-FRIENDLY]How to use dorimanx kernel - Stweaks Guide

DorimanX Stweaks Guide for the S2
Updated: 13/01/16
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Picture from DorimanX website​
Guides:​Installation
Initial Setup
Stweaks Basics
Stweaks Advanced
My setup & Troubleshooting
Credits list
Useful links:
DorimanX Official by DorimanX(ICS-->JB)
DorimanX Unofficial builds by Cybernetus, Computoncio and DorimanX(JB-->KK)
DorimanX KK Unofficial builds by gsstudios (4.4.x)
DorimanX LP/MM Unofficial builds by gsstudios (5.1.x/6.0.1)
DorimanX JB Unofficial builds by chhapil (4.1.x/STOCK JB)
DorimanX JB Unofficial builds by GreekDragon (4.1.x/STOCK JB)
General how to go on kernel tunables
CPU governors and I/O scheduler guide
Unofficial DorimanX by Cybernetus download(Recommended for 4.4.X KK)
Unofficial DorimanX by Computoncio download(Recommended for 4.X.X JB/STOCK JB)
Official DorimanX download(OK on stock 4.1.2 and below)
​
Which version to get?
So all goes like this:
Unofficial builds by gsstudios - Development stopped in 2016
12.x support = 5.1.x, 6.0.1 maliv3 only! LATEST: DorimanX 12.0 by gsstudios - ROMS include Cyanogenmod 13, Cyanogenmod 12.1
11.x support = 5.1.x maliv3 only! LATEST: DorimanX 11.0 by gsstudios - ROMS include Cyanogenmod 12.1
10.x support = 4.3.y, 4.4.y maliv3 only! LATEST: DorimanX 10.45 by gsstudios - ROMS include Slimsaber 4.4.4, SlimKK, CM11, Omni 4.4
9.x support = 4.1.y, 4.2.y, 4.3.y, 4.4.y maliv2 only! LATEST: DorimanX 9.45 by gsstudios - ROMS include CM10.1.3
8.x support = STOCK, 4.1.y, 4.2.y, 4.3.y, 4.4.y maliv1(STOCK) maliv2 all the rest! LATEST: DorimanX 8.45 by gsstudios - ROMS include Stock 4.1.2 JB, NeatROM, Omega ROM
Unofficial builds by chhapil - Development stopped in 2016
8.x support = STOCK, 4.1.y, 4.2.y, 4.3.y, 4.4.y maliv1(STOCK) maliv2 all the rest! LATEST: DorimanX 8.47 by chhapil - ROMS include Stock 4.1.2 JB, NeatROM, Omega ROM
Unofficial builds by GreekDragon - Development stopped in 2016
8.x support = STOCK, 4.1.y, 4.2.y, 4.3.y, 4.4.y maliv1(STOCK) maliv2 all the rest! LATEST: DorimanX 8.70 by GreekDragon - ROMS include Stock 4.1.2 JB, NeatROM, Omega ROM
Unofficial builds by Cybernetus and Computoncio- Development stopped in 2014
All unofficial kernels support 4.4.y ROMS!
10.x support = 4.3.y, 4.4.y maliv3 only! LATEST: DorimanX 10.44 v008 by Cybernetus - ROMS include Slimsaber 4.4.4, SlimKK, CM11, Omni 4.4
9.x support = 4.1.y, 4.2.y, 4.3.y, 4.4.y maliv2 only! LATEST: DorimanX 9.44 v005 by Computoncio - ROMS include CM10.1.3
8.x support = STOCK, 4.1.y, 4.2.y, 4.3.y, 4.4.y maliv1(STOCK) maliv2 all the rest! LATEST: DorimanX 8.44 v005 by Computoncio - ROMS include Stock 4.1.2 JB, NeatROM, Omega ROM
Official - Development stopped in 2013
9.x support = 4.1.y, 4.2.y, 4.3.y maliv2 only! LATEST: DorimanX 9.43 - ROMS include CM10.1.2
8.x support = STOCK, 4.1.y maliv2 only! LATEST: DorimanX 8.43 - ROMS include Stock 4.1.2
7.x support = STOCK, 4.1.y maliv1 only! LATEST: DorimanX 7.46 - ROMS include Stock 4.0.x, leaked 4.1.2
5.x support = 4.0.y, 4.1.2 no mali only! LATEST: DorimanX 5.92 - ROMS include Stock 4.0.x
mali = video driver (for new users that dont care to look for answers)
STOCK = Stock 4.1.2 Jellybean Update for s2
Click to expand...
Click to collapse
I've complete the basic guide on Stweaks. Now I have to start on the advanced guide!
I was looking at other device threads when I noticed that there was no guide explaining all of the things you can do in dorimanx. There were guides on how to tune other kernels but NOT dorimanX. This is well needed thread that is long overdue and should have been created ages ago. So please, be patient.
Changelog:
13/01/16:
- Added GreekDragon DorimanX JB builds into kernel list
05/05/15:
- Added a troubleshooting guide on dorimanx kernel and stweaks
- Improved kernel version guide (Added examples of ROMs)
26/04/15:
- Officially finished basic guide on Stweaks
- Overhaul of OP (Now there's a guide on what version to use)
25/04/15:
- Unofficially finished basic guide on Stweaks

Installation
I won't include a guide on how to root your phone or how to put the kernel onto your phone. I assume you already know how to root your phone.
Picture coming soon
Step 1:
Reboot your phone to recovery
Step 2
Select install zip
Step 3
Select the storage location
Step 4
Find DorimanX kernel zip
Step 5
Confirm to flash
Step 6
Let it finish flashing
Step 7
Reboot your phone to system

Initial Setup
When your phone is rebooting, you'll notice a loading bar under your phone's logo and then this screen will pop up:
No need to worry as that is the DorimanX boot/splash screen. If your phone can get past this and boot into your OS, congratulations. DorimanX has been successfully installed.
To double check if your kernel has changed, go to your phone's settings, about phone. Then scroll down until you see something similar to this:
Now lets go to the app drawer. You will see an app called Stweaks. This is the app you want to tweak DorimanX kernel.
Here is how the app looks like. It may be complicated for beginners but I will guide you through how to use it

Stweaks Basics
Note: This is the i9100 version of dorimanx stweaks. I will not make a guide for the newer dorimanx stweaks app since I don't have the LG G2! However, if someone can provide screenshots, I'm sure I can do something about it!
CPU
Boot CPU frequency:
The CPU frequency that your phone will run at while booting or at startup. Increase this for faster boot speed, decrease for better battery life and stability.
My Recommendation: Leave it to defaults
Boost CPU frequency:
The CPU frequency that your phone will run whenever there is a sharp increase in CPU load. Increase this for faster responsiveness, decrease for better battery life. Please note that you can't set this value higher than the max cpu frequency. It's COMMON-SENSE!
My Recommendation: Leave it to defaults
Max Normal Frequency:
The CPU frequency that your phone will run before going to max frequency. This won't do much to your phone's CPU frequency, so it's best to leave it to defaults unless underclocking.
My Recommendation: Leave it to defaults
Max OC Frequency:
The overall max CPU frequency your phone will run at. Increase this for better responsiveness and processing speed, decrease if you want better battery life.
My Recommendation: Leave it to defaults unless you want to overclock or underclock
Min Frequency:
The minimum CPU frequency your phone will run at. Increase this for better responsiveness and processing speed, decrease if you want better battery life.
My Recommendation: Leave it to defaults unless you want to overclock or underclock
CPU-VOLTAGE
This section of Stweaks allow you to undervolt and overvolt your CPU. Please note that undervolting (UV) your CPU will decrease phone stability if set too low, whereas overvolting (OV) will decrease your CPU's lifespan and generate more heat.
CPU Voltage main switch:
Ticking this enables set CPU voltages. If your phone reboots from instability, stweaks will most likely be resetted to protect your phone from any further problems.
Check CPU Voltage Group:
Using this button checks what CPU voltage group your CPU is using. The Galaxy S2 has 5 different CPU types around the world, the most common is number 3 and the most stable is number 4 and 5. Number 2 and 1 are old CPU types and need more voltage to be stable. If your CPU type is 1 or 2, don't UV much otherwise you'll get SODs. Remember that the higher the number, the more undervolt you can apply on your CPU. If you are downloading someone else's profile and they have a different CPU voltage type, try to avoid using it. Higher voltage require higher voltages to be stable, but at the cost of heat and battery life. Please be careful if you are considering to overclock your CPU!
If you want to undervolt, here are some safe voltages you can set (see link below), just set the sliders to the same voltages for the corresponding frequencies:
https://docs.google.com/spreadsheets/d/1MlV6Tbfo_7_QEUnTkfpdioSSPSDSWPJLRxL8Z00A8yA/edit?usp=sharing
CPU-TUNING (AWAKE)
Default CPU governor:
The default CPU governor when your phone is awake (screen is on). DorimanX kernel by default gives users an option to change to various governors such as HYPER, Ondemand and NeoX. Changing this will affect your phone's responsiveness and multitasking performance. For more information about governors, visit my guide: http://forum.xda-developers.com/general/general/ref-to-date-guide-cpu-governors-o-t3048957
My Recommendation: The default governor (HYPER for the i9100) is responsive and stable for everyday usage, you can change it if your want.
Hotplug_Enable:
The hotplugging governor for your phone. You can choose from Alucard hotplug, Intellihotplug, enabled auto and disabled.
My Recommendation: Leave it to defaults. Enabled Auto setting will select the best hotplugging governor for your device.
Gov Policy Install:
This applies all the changes to the CPU governor settings and tunables. It is required by the user to press this if they want to keep the CPU settings.
Up Threshold:
Measured as percentage, when load on CPU is equal or above this threshold, your CPU will scale up.
Lower value = early scale up, and vice versa. (Applies only to HYPER, Ondemand, Intellidemand, PegasusQ, Conservative, Sleepy and zzmanX)
Default value = 60%
My Recommendation: Change it to 70% for better balance between battery life while keeping good performance.
Up Threshold at min freq sleep:
This threshold is used as up threshold while sampling rate is at frequencies less than freq_for_responsiveness. Above that, normal up_threshold is used.
Lower value = early scale up, and vice versa. (Applies only to HYPER, Ondemand, PegasusQ)
Default value = 50%
My Recommendation: Leave to defaults
Sampling rate sleep:
This factor determines how often the governor should poll for CPU usage in terms of frequency and load percentage to make scaling decisions.
Lower value = early scale up, and vice versa. (Applies only to HYPER, Ondemand, Intellidemand, PegasusQ, Conservative, Nightmare, Darkness Sleepy and zzmanX)
Default value = 60000uS
My Recommendation: Leave to defaults
Freq for responsiveness sleep
Long story short, this is setting is the frequency before the CPU goes to lower frequencies. It prevents any lag spikes from happening.
Lower value = More battery life, but more lags! (Applies only to HYPER, PegasusQ and Nightmare)
Default value = 400000kHz
My Recommendation: Leave to defaults
Down threshold sleep:
This is the same as the up_threshold but for the opposite direction.
Lower value = Frequencies reduced faster, and vise versa. (Applies only to HYPER, Ondemand, Intellidemand, PegasusQ, Conservative, Nightmare, Darkness Sleepy and zzmanX)
Default value = 30%
My Recommendation: Leave to defaults
CPU-TUNING (SLEEP)
Settings are pretty much the same as the awake CPU governor settings, but there are slight changes to the CPU governor tunables (more info on that later).
Deep-Sleep CPU governor:
The default CPU governor when your phone is in deep sleep or standby (screen is off). DorimanX kernel by default gives users an option to change to various governors such as HYPER, Ondemand and NeoX. Changing this will affect battery life and stability. For more information about governors, visit my guide: http://forum.xda-developers.com/general/general/ref-to-date-guide-cpu-governors-o-t3048957
My Recommendation: The default governor (Ondemand for the i9100) is responsive and stable for everyday usage, you can change it if your want.
IO
Kilobytes To Read-Ahead:
This only applies to the external sd card. This setting determines the kilobytes to read-ahead for your external sd card. Changing this will affect the transfer speeds to your phone's external sd card.
My Recommendation: Leave it to defaults. Auto setting will select the best setting for your device.
Default Awake IO scheduler:
This will set the default IO scheduler when your phone is awake (screen-on). There are many IO schedulers included with dorimanX kernels such as SIO, ZEN, BFQ and CFQ. Changing this will affect transfer speeds, phone responsiveness and load times. For more information about IO schedulers, visit my guide here: http://forum.xda-developers.com/general/general/ref-to-date-guide-cpu-governors-o-t3048957
My Recommendation: You can leave it to the default IO scheduler. I'm sure that the scheduler dorimanX chooses is stable, so if you don't know much about IO schedulers, leave it to defaults. However, I do recommend changing it to a simpler scheduler such as SIO and ZEN which have low overheads and less IO lantency.
Standby and Deepsleep IO scheduler:
The default IO scheduler when your phone is on standby or in deepsleep (screen off).
My Recommendation: Keep it the same as the awake IO scheduler. You can make it different from the awake scheduler if you really want to (but I don't recommend this).
Memory
AUTO OOM
Stands for Automatic low memory management, this allows the low memory management settings to be applied automatically or to take effect on your phone.
Default: Ticked
My Recommendation: Keep it ticked.
OOM Level Screen ON
The setting for the level of low memory management when screen is on. More aggressive settings leads to more free RAM but more killed apps.
Default: Aggressive
My Recommendation: Change it to medium as I believe it's the sweet spot for our phone.
OOM Level Screen OFF
The setting for the level of low memory management when screen is off. Same scenario applies where more aggressive settings leads to more free RAM but more killed apps.
Default: Medium
My Recommendation: Leave to defaults.
GPU
VPLL MODE
Ticking this box allows users to overclock the gpu even further than the default allowed frequencies. Please note that higher frequencies need more voltage, but there is the risk of damaging your GPU if too excessive.
Default: Unticked
My Recommendation: Keep this unticked. This settings is for the advanced overclockers and and tweakaholics. It is too risky keeping this enabled
GPU utilization timeout
This settings changes the CPU utilization timeout calculation. Basically this tunes the ramp up aggresiveness for the GPU, much like the CPU thresholds. Smaller values give faster GPU response but more battery drainage and vice versa.
Default: 400MSec
My Recommendation: Keep to default value.
GPU frequency steps
Dorimanx Kernel includes 5 GPU steps. These steps allow the GPU to scale frequencies efficiently and is originally made to save battery when not busy.
My Recommendation: Keep to default values unless you want to overclock.
GPU voltage steps
Complementing the frequencies, these settings are the GPU voltages for each step. Much like CPU voltages, settings these values too high will result in damage to the GPU, while not having enough voltage will result in instability.
My Recommendation: Keep to default values unless you want to overclock.
Screen
Min BL
Stands for minimum brightness level. Higher value will result in staying in the lowest brightness level for brighter conditions.
Default: 30
My Recommendation: Keep to default values.
Min Gamma
The setting to adjust minimum brightness level.
Default: 1
My Recommendation: Keep to default values.
Max Gamma
The setting to adjust minimum brightness level.
Default: 23
My Recommendation: Keep to default values.
Other settings will be explained in advanced guide!
Sound
Headphone Amplifier:
This setting allows you to adjust the headphone amplification level. Increase this if you want your headphones to sound louder.
My Recommendation: Keep to Disabled or Reset unless you want to boost headphone volume. I don't really recommend increasing this value.
Volume levels and Gain Controls:
These settings should be pretty straightforward, they're clearly labeled. Increase these values to boost the recording/playback volumes.
My Recommendation: Keep values to 0dB unless you want to boost headphone volume. I don't personally increase these values.
BLN
BLN stands for Backlight notification, meaning that your phone's buttons will light up whenever your phone gets a notification.
BLN
Tick it to enable Backlight notification. Please note that BLN will increase your phone's battery drainage when enabled.
My Recommendation: I don't personally enable BLN. Enable it if you want to.
BLN effect
This setting will set LED behavior for BLN, if BLNWW (BLN without wakelock, without getting CPU out of deep sleep) is on, the effect can only be steady. Options include steady, breathing and blinking.
My Recommendation: I don't personally enable BLN. Enable it if you want to.
Notification Timeout
This setting determines how long the Backlight Notification will stay on for. Time ranges from never to 2 hours.
My Recommendation: I don't personally enable BLN. But keeping it to a shorter value will save you battery.
Force LEDS disabled
The title says it all, forces your touch LEDs off if enabled.
My Recommendation: I don't personally enable BLN. Change the settings if you need this function
LED Timeout
This setting determines how long your phone's touch LEDs will light up when touched or when using touch screen.
Default value = 3 sec
My Recommendation: I don't personally enable BLN. Change the settings if you need this function
BLNWW
BLN Without Wakelock. This is a more battery efficient BLN but has less features than normal BLN. Enabling this (while BLN is also enabled) will let the CPU continue to sleep during BLN and save battery.
Default value = Ticked
My Recommendation: I don't personally enable BLN. Tick the setting if you need this function
The rest of the BLN settings should be pretty straightforward
Other
DorimanX has included scripts in his kernel that can optimize the phone by during certain conditions(time) or they can be applied straight away. The settings should be well explained anyway or straightforward.
Cron task main switch
Enable this to enable all set tasks. You need to enable this otherwise the set tasks will not be done!
My Recommendation: I don't personally enable Cron. Tick the setting if you need this function
Cron task main switch
Press this to test if the Cron task service is online or not. If the service is offline and you've enabled cron, the your ROM needs to be updated. (Busybox out of date)
Cron reset
Press this button to reset the scripts and jobs from kernel and to refresh the configuration. This will clear all your custom changes.
Tweaks
Cortexbrain is a script created by DorimanX that can manipulate many kernel settings based on chosen Stweaks profiles and settings and on screen state. It is so useful that the kernel enables it as default.
Cortexbrain-Background-Process
Enables or Disables the Cortexbrain background process.
Default: Enabled
My Recommendation: Leave it to enabled!
Check Background-Process
Checkes whether the Cortexbrain background process is running or not.
Android logger control
Controls what you can see in android logcat.
Default: AUTO
My Recommendation: Leave it to AUTO!
Modules will covered in advanced guide
Profiles
Here is the menu you want to manage all of the custom profiles available on stweaks
Profile Check:
Checks what profile you are currently running. By default, dorimanX kernel uses the default profile, and all changes will be saved there.
Profiles:
Include:
- Extreme battery
- Battery
- Default (Default)
- Performance
- Extreme Performance
I don't recommend uses the other profiles since they are outdated or can be further optimized.
Backup or Restore
This section allows users to backup and restore the settings in stweaks. It will take approximately 30secs for stweaks to restore user settings. The app will restart and the values should all be restored.
Settings Backup
Press this button to backup your stweaks settings. The settings will be saved in the internal sd card on your phone and will be called default.profile.backup. You can open this file in notepad or wordpad to edit settings externally
Settings Restore
Press this button to restore your stweaks settings. Read the description of the section about how long to wait and app behavior.
Dualboot
This section allow you to reboot your phone in several ways. DorimanX kernel supports dualbooting, and you can boot into 2 different roms during the boot process or via app. In order to boot into 2nd rom, the 2nd rom needs to be installed first. To install second rom, go into recovery and dualboot settings. The buttongs should be straightforward here
Bug-Report
Allows users to report any stweak/kernel specific bugs. Pressing this button will create a log file on your internal sd card which can be used to diagnose any kernel problems.
Partitition Status
Use this button to check your phone's partitions for errors (data, system, cache, efs and preload). This will NOT fix any errors, it will just check. To fix, backup your files with a backup app or making a nandroid backup (backup via recovery), then press the data and cache fix button located in the OTHER tab. USE IT AT YOUR OWN RISK SOME DATA MAY BE LOST DURING THE FIXING PROCESS! If there's any broken apps, reinstall them. If you get bootloop, reinstall rom. If you are stuck on boot, wipe phone than install rom. If it says your partitions are CLEAN, your partitions should have no errors. Usually if your partitions has errors, the stock browser will pop up saying that your partitions need to be fixed.
Kernel-Update
Allows to check of updates. Again this feature doesn't work properly anymore. And so ignore the message saying that there is a newer version of the kernel!
Extras
Gives info about your phone. That's about it!
For now, I will be taking a break. Wait to tomorrow for more info!

The following settings only apply to my personal dorimanx builds
Other
TCP algorithm
Congestion control strategies (or algorithms) are used by TCP, the data transmission protocol used by many Internet applications. The main goal of a TCP algorithm is to avoid sending more data than the network is capable of transmitting, that is, to avoid causing network congestion. Different algorithms respond differently to network loads, but they are all based on the same principle of avoiding network congestion.
This setting allows you to choose what TCP algorithm should be used for internet transmission. Changing this will result in changes to latency and download speeds (differences are marginal or hard to measure).
My Recommendation: Use Westwood or Cubic as they are the most reliable and best for performance.

Troubleshooting
This is the troubleshooting section of the guide. It is important that you read this first before blaming anyone else. Remember that in XDA, we are here to help each other.
Phone doesn't boot?
There may be a few cases where after you flash dorimanX kernel, your phone will fail to boot. This is quite a broad problem which has many aspects that may have caused this to occur. The common mistake is people do not read before they flash. THAT IS FINE, EVERYONE HAS TO START SOMEWHERE. Simply read the post regarding to kernel versions, download the correct version, put it on your phone, then flash the kernel.
If that doesn't work, we can narrow the problem down to the file you've downloaded or the custom recovery. There is chance that the kernel zip you've downloaded is corrupted. If that's the case, download it again. If you have trouble installing a kernel on your phone, flash a kernel .tar file via ODIN. Need a .tar file, have a look at my guide here:
Stweaks doesn't save my settings
Stweaks has safety features that safeguard your phone from any damage, especially from overvolting and overclocking. Because of this, the values will reset to defaults. As frustrating as it is, this is the only way for keeping your phone from its death. There are some cases where Stweaks doesn't even save your settings, this is usually because of the app it misbehaving (aka glitching) or it's because of permission issues. If you face this problem, try reflashing the kernel. Reboot your phone and see if it's working properly. If not, you may have issues with the permissions given to stweaks. Check if you've given root access to stweaks, without root, stweaks is useless.
After installing dorimanX kernel, my battery life has been horrible
If you face battery problems after installing dorimanX kernel, you can revert to a previous backup of your rom and kernel or flash a different kernel. Kernel developers don't intend to make kernels that use a lot of battery life, in fact, it's the opposite. Most issues regarding to battery life is usually caused by the kernel not being able to determine the new setup environment. Give your phone a few charge cycles before you make your judgement! Battery life is usually affected by the combination of both ROM + Kernel, so the combination is very important if you consider battery life!
My phone freezes when screen is off/Freezes when screen switches on
Also known as Sleep Of Death (or SOD), this can occur when a value changed regarding to the CPU or GPU is changed to unstable values. This issue commonly occurs when you undervolt your CPU too low, causing the CPU to be unstable. In a event such as this, force your phone to reboot by removing and re-inserting your phone's battery. After that, Stweaks would have already reset to defaults, removing any further instabilities. If you still consider changing those values, try reduce the amount of the value you are changing.
My phone reports that there is 16 CPU steps. Shouldn't there be less
I won't go too technical in this, but in simple, DorimanX include more than the required CPU frequency steps to allow CPU frequencies to scale efficiently. By samsung default, there is 5 CPU steps. The advantages of having 16 steps is that CPU scaling will be more efficient as the frequencies don't scale up or down too frequently as middle frequencies are used. Also, this allows the user to have more control over the overclocking and voltage capabilities over the CPU. You cannot change the number of steps unless you change the CPU governor to darkness.
Phone is laggy on boot up
Isn't it always the case that your phone is laggy when you first boot up your phone? Your phone needs to load all of the services and startup apps before you can fully use your phone. Give your phone a little patience then enjoy your new experience.
My Setup
Phone: Samsung Galaxy S2 i9100
DorimanX kernel version: 10.44 v008
Max CPU frequency: 1200mhz
Min CPU frequency: 200mhz
Undervolting: -20mV for each step
Awake CPU gov: HYPER
Sleep CPU gov: Ondemand
I/O scheduler: SIO

Credits List
- DorimanX (the master behind DorimanX kernel)
- Cybernetus (for providing the last real DorimanX kernel for i9100 users)
- Computoncio for also providing i9100 users dorimanx builds
- Other XDA members that I haven't listed

Guide updated on the 21/04/15. Please be patient. I have school work to worry about too.

gsstudios said:
Guide updated on the 21/04/15. Please be patient. I have school work to worry about too.
Click to expand...
Click to collapse
Good thread, will be very useful to "new" i9100 survivors who's looking for a way to tame one of best custom kernels around..
Just a suggestion, you might want to add informations about CPU Group limitation/compatibility related to OV/UV, as one setting wont fit all..
And also there is no safe voltage guidelines for each groups yet, just incase you wanna go there

Twiq said:
Good thread, will be very useful to "new" i9100 survivors who's looking for a way to tame one of best custom kernels around..
Just a suggestion, you might want to add informations about CPU Group limitation/compatibility related to OV/UV, as one setting wont fit all..
And also there is no safe voltage guidelines for each groups yet, just incase you wanna go there
Click to expand...
Click to collapse
I'll see what I can do today
Update: Added a few more descriptions. Still busy with school work....

@gsstudios
I recomand u to try to sec cpu thread shold (boost up) higher at 1000 mhz and 1.2 ghz ?
Why ?
I'm using my phone with maximium freq 800 mhz. And it is still smooth and fast. Even in game in which i normally had big heat up and batt drain is smooth. Phone is only laggy when mediascanner is running or app is installing. I'm olso using Live Wall Paper.
And why higher boost up not maximum freq 800 mhz ?
Because if u open app like Asphalt and Real Racing or Facebook [emoji14] phone will go to higher frequences but only when it is important. And imoprtant doesnt mean scrolling through app drawer
Wysłane z Cyano-fonika 11 nightly...

MikiGry said:
@gsstudios
I recomand u to try to sec cpu thread shold (boost up) higher at 1000 mhz and 1.2 ghz ?
Why ?
I'm using my phone with maximium freq 800 mhz. And it is still smooth and fast. Even in game in which i normally had big heat up and batt drain is smooth. Phone is only laggy when mediascanner is running or app is installing. I'm olso using Live Wall Paper.
And why higher boost up not maximum freq 800 mhz ?
Because if u open app like Asphalt and Real Racing or Facebook [emoji14] phone will go to higher frequences but only when it is important. And imoprtant doesnt mean scrolling through app drawer
Wysłane z Cyano-fonika 11 nightly...
Click to expand...
Click to collapse
Nice.

Guide updated today. Finished the basic guide to stweaks. Now will start to work on advanced guide. Please note that I will NOT go through every setting in stweaks, but I'm going to cover the more important ones instead. Advanced guide should be completed by next week.

@gsstudios
I have a little problem.
I have olny toutched setting u told that we can savety touch. And u have a problem. Whan i leave device without touching it , the cpu frequency wont go under 500 mhz. Is that normal ?
Wysłane ze Slim-Saberd-fonika 4.3.1 R powered by DorimanX v008 kernel

MikiGry said:
@gsstudios
I have a little problem.
I have olny toutched setting u told that we can savety touch. And u have a problem. Whan i leave device without touching it , the cpu frequency wont go under 500 mhz. Is that normal ?
Wysłane ze Slim-Saberd-fonika 4.3.1 R powered by DorimanX v008 kernel
Click to expand...
Click to collapse
What setting was this? Was it the up threshold. Try resetting back to default values to fix problem.

@gsstudios
Problem fixed.
Rebooted device and now it goes lower.
Ps. I use really big up threshold. 73 % : )
Wysłane ze Slim-Saberd-fonika 4.3.1 R powered by DorimanX v008 kernel

@gsstudios
Can u post in one od OP post full stock CPU voltages ? I noticed , that STweaks changed my setting a few times (lowerd my CPU freq and staff like that) and now I'm not sure if i have my lower volatages are set or they are resetted to default.
Wysłane ze Slim-Saberd-fonika 4.3.1 R powered by DorimanX v008 kernel

Great job ..will help lots of people...

Troubleshooting guide is up. Enjoy

Thnq

★ Kernel Profile Sharing Thread for LG G3 ★

Introduction:
Hey there, this thread is all about sharing profile setups for our beloved G3.
Feel free to share your settings too or PM me and i link it straight to the second post ​
A few things explained:
Android Modders Guide ( thanks to @gsstudios )
Explanation of LMK & Adj and Minfree settings ( thanks to @Papa Smurf151 )
What is ZRAM and how does it work??? ( thanks to @-CALIBAN666- )
How to apply Synapse Profiles:
Code:
- Unzip
- Move .tgz file to your Internal storage > Synapse > saved_profiles
- Profile > Profiles > choose .tgz file > press "check-mark" and not "X" > choose "restore profile"
- Synapse will restart and then press "X"
- Check all values and if you have to change something press "check-mark"
How to reset Synapse Profiles:
Code:
tools > clear synapse data > restart device > start synapse > choose "check-mark" = stock values

--= Android 5.x.x Profiles =--
gr3ud´s synapse profiles:
R21 Profile with EuphoriaOS & 777 Kernel ( thanks to @777jon )
--> Old/Experimental/Beta Profiles - Android 5.1.1 @ 777Kernel (R21)
--> Old/Experimental/Beta Profiles - Android 5.1.1 @ 777Kernel (R15 - R20)
--= Android 6.x.x Profiles =--
gr3ud.6.0.1.V1 - Alucard + Alucard Hotplug
http://pastebin.com/jEKAmYVZ
CPU:
- MSM Limiter: Disabled
- min: 300MHz
- max Freq: 2457 MHz
- Governor: Alucard
- CPU Tunables:
> cpus_down_rate: 4
> cpus_up_rate: 1
> freq_responsiveness: 2256
> sampling_rate: 50000
- Multicore Powersaving: Disabled
- CPU Boost: Interval: 0ms / Sync Threshold: Disabled / Input Interval: 1000ms / Input Boost: 1958 MHz
CPU Voltage (optional for extra battery):
- Global Offset: -25 (stable, tested with Antutu)
HOTPLUG:
- Alucard Hotplug
- Sampling Rate: 50%
- Prevent to Suspend: Disabled
- Minimum CPUs Online: 4
- Maximum CPUs Online: 4
- Max Cores Screen Off: 2
THERMAL:
(optional) Thermal Compound Cooling Mod -> https://www.youtube.com/watch?v=PH5wCeootNI
- Intellithermal Enabled
- Core Control OFF
- Freq Throttle Temp = 75°c
- Core Throttle Temp = 80°c
GPU:
- min. freq.: 330
- max. freq.: 547
- Governor: msm-adreno-tz
- Simple GPU Algorithm: Enabled
- Laziness: 10
- Ramp Threshold: 0
- Adreno Idler: Disabled
SCREEN ("personal preference/vibrant colors"):
- Saturation Intensity: 60
- Screen Value: 120
- Screen Contrast: 148
I/O:
- Internal Storage: ZEN (128 kB)
- Rotational Storage: Off
- Add Random: Off
- I/O Stats: Off
- RQ Affinity: 0
KSM:
- Disabled
LMK:
- Adaptive Low Memory Killer: Disabled
Virtual Memory:
- Laptop Mode 1 = more performance but can cause random reboots (use this only with stable builds)
- Z-RAM: Disabled
Misc Controls:
F-Sync: Disabled = more performance but can cause random reboots and data loss ( use this only with stable builds)
★ souler456´s profile - Slim + IntelliPlug ★
http://forum.xda-developers.com/showpost.php?p=66659439&postcount=343 ( thanks to @souler456 )

1st
gr3ud said:
List of shared profiles:​
My profile with 777 Kernel (R21) + Euphoria-OS 1.1 (Android 5.1.1) (thanks to @777jon ):
- Performance Profile (aka " almost Nexus smooth")
- Not very battery friendly (~3h - 5h SOT with default 3000 mAh battery)
- I don't know how it works out for "Gamers" because i just run simple 2D games when i got the time for that.
- Please don't expect too much, this works for me and my daily usage.
- Enjoy
Setup Values:
CPU:
min: 345 MHz
max: 2457 MHz
MSM Limiter: Disabled
Debug Mask: OFF
Suspend Min Frequency: irrelevant but 345 MHz
Resume Max Frequency: irrelevant but 2457 MHz
Suspend Max Frequency: irrelevant but 2457 MHz
Suspend Defer Time: irrelevant but 0
Input Boost Frequency: 2457 MHz
Boost interval: 5000 ms
Min Input Interval : 100ms
Maximum CPUs Boosted: 4
Multi-core Power Saving: OFF
Arch Power: OFF
CPU Governor(0-3): Nightmare
HOTPLUG:
Msm Hotplug Driver: Enabled
min: 4
max: 4
boost: 4
Screen Off: 2
Boost Lock: 5000 ms
Down Lock Duration: 5000 ms
History Size: 1
Fast Lane Load: 0
Offline Load: 0
Suspend Defer Time: 0
Thermal: ( I use "thermal paste/copper shim mod" so you may choose higher values without)
Intellithermal: Enabled
Core Control : Enabled
Frequency Throttle Temperature: 80c
Core Throttle Temperature: 85c
I/O:
Read-ahead Size: 1024 KB
I/O scheduler: zen
CRC Control: OFF
MMC Clock Scaling Control: ON
Add Random: OFF
I/O Stats: OFF
Rotational: OFF
No Merges: All
RQ Affinity: Disabled
NR Requests: 128
GPU:
GPU min Frequency: 27 MHz
GPU max Frequency: 657 MHz
GPU Governor: Performance
All Add-on´s : Off
GAMMA:
Saturation: 270
Memory(experimental): (beta = ** stock values)
Z-RAM: 0 MB
Dirty Background Ratio: 80% (**5%)
Dirty Ratio: 90% (**40%)
Dirty Expire Centisecs: 200 cs
Dirty Write-back Centisecs: 500 cs
Drop Caches: ON
Extra Free KB: 49050 kB (**43200 kB)
Laptop Mode: ON
Swappiness: 60% (**10%)
VFS Cache: 10% (**100%)
Misc:
TCP: cubic - westwood or what you desire.
How to test:
Run net speed tests with each protocol at least 3 times to compare the average with this Speedtest App
Power Suspend Mode: LCD Hooks
FSYNC: ON
ADV:
Krait-C States: All ON
KSM: ON
Pages to Scan: 128
Scan Delay Interval: 750
Deferred Timer: OFF
Gentle Fair Sleepers: OFF
Adaptive LMK: OFF
Build.PROP:
Wifi Scan: 300 sec
VM Heapsize: 512 MB
Allow purging of assests: OFF
Tools:
SELinux Status: Permissive
--------------------------​
Click to expand...
Click to collapse
Nice to see you made a thread bro

Well, this is the perfect place to share your "imagination". Great
Sent from my LG-D855 using Tapatalk

? ? ? much appreciated effort here ? ? ?

Thank you for creating a profile thread!

Got 40066 in Antutu yesterday on your 30th October set up.
Got this today with the 31st October.
Might not sell my G3 for a OnePlus X now.

johnnzey said:
Got 40066 in Antutu yesterday on your 30th October set up.
Got this today with the 31st October.
Might not sell my G3 for a OnePlus X now.
Click to expand...
Click to collapse
Hey mate glad to hear, i would personally wait for custom 6.x.x ROMs/Kernels for our device tho before moving on
To all others, thanks for your kind words i appreciate it
But without @m1trand1r and @metalgearhathaway motivating words + all the other dudes that dig my work, this thread would not exist :good:
Cheers.

Just applied your settings, great! Never had such a smooth G3! Thanks for the update!

What settings do you use for Marshmallow?

@6th_Hokage
Well since Synapse does not play nice for me and i generally have some weird issues with custom kernels on 6.x.x ROMs (Overheating,BSODs,Crashes,Random Reboots,etc) i decided to use the ROMs respective kernel.
I�´m trying Broken OS right now and they know their stuff pretty well.
They have Kernel Adiutor inbuilt so i basically switched just a few things...like:
- zzmove CPU gov with profile 8 and its inbuilt hotplug, changed the "punch freq" to 2457MHz
- CPU Boost/Interval 5000ms, Sync/Boost Freq. @ 2457MHz
- GPU min/max 587MHz with msm adreno gov
- I/O: row or zen @ 512kB
- Kernel Sampage Merging with 300 pages / 1000 ms scan
- I disabled Adaptive LMK
- Enabled Laptop Mode
- Entropy: Read 128 / Write 256
...and that's pretty much it, its not battery friendly but i don't care for battery life, still got 4hs of SOT with that setup... Lionheart works well too on 6.x.x also does smartmax , so yeah, its butter smooth as i like it for now, i miss KCAL stuff tho, but this ROM (BrokenOS) is still in alpha phase so there will be much more stuff added in the next releases from what i�´ve read on G+
I�´m also waiting for Eliminater74�´s own Kernel Manager, then i will play around with hes kernel i guess so stay tuned :good:
Also, some users mentioned that my 5.1.1 profile works very well for them on 6.x.x maybe give it a shot.
edit:
I forgot to mention that i also disable the default hotplug with Lionheart or smartmax to have all 4 cores permanent online for a little extra performance boost.

Thanks bro. Good job.

*Android 6.x.x update*
http://pastebin.com/jEKAmYVZ

Thank you for the excellent kernel setup for Marshmallow. My G3 is so much smoother than before. I give it a two thumbs up.

**Android 7.x.x Update**
CPU:
- MSM Limiter: Disabled
- min: 300 MH
- max Freq: 2457 MHz
- Governor: Nightmare
- Multicore Powersaving: Disabled
- CPU Boost: Interval: 0ms / Sync Threshold: Disabled / Input Interval: 2500ms / Input Boost: 2265 MHz
HOTPLUG:
- All Disabled
THERMAL:
(optional) Thermal Compound Cooling Mod -> https://www.youtube.com/watch?v=PH5wCeootNI
- Delete "Thermal-Engine" under system/bin
- Intellithermal Enabled
- Core Control Disabled
- Freq Throttle Temp = 75°c
- Core Throttle Temp = 80°c
GPU:
- min. freq.: 330
- max. freq.: 578
- Governor: msm adreno-tz
- Simple GPU Algorithm: Disabled
- Adreno Idler: Disabled
SCREEN ("personal preference/vibrant colors"):
- Saturation Intensity: 55
- Screen Value: 125
- Screen Contrast: 140
I/O:
- Internal Storage: bfq
- Read-ahead: 512 kB
- Rotational Storage: On
- Add Random: Off
- I/O Stats: Off
- RQ Affinity: 0
KSM:
- Disabled
LMK:
- Adaptive Low Memory Killer: Disabled
Virtual Memory:
- Laptop Mode = Disabled
- Z-RAM = 500 MB (16/2GB model only)
Misc Controls:
F-Sync = Enabled

gr3ud said:
**Android 7.x.x Update**
CPU:
- MSM Limiter: Disabled
- min: 300 MH
- max Freq: 2457 MHz
- Governor: Nightmare
- Multicore Powersaving: Disabled
- CPU Boost: Interval: 0ms / Sync Threshold: Disabled / Input Interval: 2500ms / Input Boost: 2265 MHz
HOTPLUG:
- All Disabled
THERMAL:
(optional) Thermal Compound Cooling Mod ->
- Delete "Thermal-Engine" under system/bin
- Intellithermal Enabled
- Core Control Disabled
- Freq Throttle Temp = 75°c
- Core Throttle Temp = 80°c
GPU:
- min. freq.: 330
- max. freq.: 578
- Governor: msm adreno-tz
- Simple GPU Algorithm: Disabled
- Adreno Idler: Disabled
SCREEN ("personal preference/vibrant colors"):
- Saturation Intensity: 55
- Screen Value: 125
- Screen Contrast: 140
I/O:
- Internal Storage: bfq
- Read-ahead: 512 kB
- Rotational Storage: On
- Add Random: Off
- I/O Stats: Off
- RQ Affinity: 0
KSM:
- Disabled
LMK:
- Adaptive Low Memory Killer: Disabled
Virtual Memory:
- Laptop Mode = Disabled
- Z-RAM = 500 MB (16/2GB model only)
Misc Controls:
F-Sync = Enabled
Click to expand...
Click to collapse
thank you,,with those do you get decent battery..

jlb1959.01 said:
thank you,,with those do you get decent battery..
Click to expand...
Click to collapse
It's okay, was not really my intention to save battery juice.

gr3ud said:
It's okay, was not really my intention to save battery juice.
Click to expand...
Click to collapse
thanks,looking for mid point settings,both perform and some kind of battery..thanks again..

jlb1959.01 said:
thanks,looking for mid point settings,both perform and some kind of battery..thanks again..
Click to expand...
Click to collapse
Hmm try my 6.x.x alucard profile then, had some good experience with it. No problem btw you welcome

gr3ud said:
Hmm try my 6.x.x alucard profile then, had some good experience with it. No problem btw you welcome
Click to expand...
Click to collapse
I will try it,,much appreciated..