Help! My kindle fire is bricked! - Kindle Fire General

okay so i installed cm9 on my kindle fire so then i started screwing around with twrp
so then i dont know if my battery was near 0 percent because this was along time ago but on kfu it wont recognize the adb. Any Thoughts?

Not to be rude, but could you explain that again? Only this time make it somewhat intelligible.
I'm just saying...
Sent from my Amazon Kindle Fire using xda premium

Beeyoth said:
okay so i installed cm9 on my kindle fire so then i started screwing around with twrp
so then i dont know if my battery was near 0 percent because this was along time ago but on kfu it wont recognize the adb. Any Thoughts?
Click to expand...
Click to collapse
Do you have FFF installed?
Gửi từ Kindle Lửa của tôi qua Tapatalk 2

Beeyoth said:
but on kfu it wont recognize the adb. Any Thoughts?
Click to expand...
Click to collapse
What do you mean kfu won't recognize adb? If you mean on kfu, the status is coming up as offline? Did you try :
(i) check device status in kfu after leaving it connected to the pc on usb for some time
(ii) on/off a few times and then check
(iii) try setting boot to Normal and reboot
(iv) install drivers again and try
If you meant that adb itself is not found, may be you deleted the small adb.exe by mistake

If you have the adb tools installed, have you tried fastboot to see if it recognised? I found that when I bricked mine, KFU did not see the device (i.e. adb devices showed nothing), but fastboot devices did work and I was able to push FFF and recovery to it. There are a few good posts on the process in the forums....good luck!

If it wont come on at all or is turning on and turning off quickly you'll need to charge it for a day from your PC or from the wall to get enough charge for it to boot up. Happened me twice this week.

give fastboot a try. if not, keep it plugged in for a while and try again later. a little patience can go a long way. worst comes to worst, a factory cable should do the trick.

Related

Computer unable to recognize kindle stuck at Boot logo

I've attempted to install drivers, but it still isn't recognized by fastboot, kindle fire utility, and everything else. I reconnect it to my computer and it just comes up as "Unknown usb device"... It came to be this way because while I was installing TWRP with Kindle fire utility it froze and it's been like that for at least 30 minutes now. I've tried restarting it, resetting it, and nothing is working. Please help!
Look here http://forum.xda-developers.com/showthread.php?t=1417966
You maybe need to change boot mode to normal
Sent from my Kindle Fire using Tapatalk
But how do I manage to change the bootmode when my computer won't recognize that my kindle is connected?
Sent from my MB525 using XDA App
Follow the instructions posted by me, there and then your device should be recognized....
Sent from my Kindle Fire using Tapatalk
http://forum.xda-developers.com/showpost.php?p=20421225&postcount=222
Had the same issue. This solution worked for me
guillotinedream said:
http://forum.xda-developers.com/showpost.php?p=20421225&postcount=222
Had the same issue. This solution worked for me
Click to expand...
Click to collapse
I love you. No homo, of course. Thanks a ton! This worked great for me. I thought that my kindle was screwed Thanks so much for that!
lol You're welcome. Glad it worked for you
Computer doesn't even recognize that a device is connected...
Okay, I'm not having the same issue, but I'm pretty sure I've completely, irevicalbly, bricked my kindle.
I know that I'm not in Fastboot mode, I've experienced that issue and solved it with the KFU.
Here's what I did:
I used the KFU to root my kindle. That worked fine. I was able to load all the Google apps (which was my initial goal). Then, I got greedy and decided that ICS was my next step - oops.
I followed the instructions on the following site:
androidauthority.com/kindle-fire-miui-4-ics-55853/
Note: I know, I'm an idiot - I should have paid attention to comments! UGH!
After I did this, I now only get the firefirefire logo and that is it. I can't load/reload TWRP and I can't change my bootmode to normal or recovery. The thing is, no matter which computer I plug the device into, the computer won't recognize the device. I get a message saying something "malfunctioned" when I plug it in. I've tried 3 different Windows machines (I've installed/reinstalled drivers I don't know how many times!) and I even tried loading Linux on a spare laptop and that didn't work either.
So, I tried the next thing I could think of. I followed the instructions on the following site:
ramble.karrth.com - Section "Troubleshooting TWRP
which involved removing the back cover, shorting a circuit (to force usbboot) and plugging my Kindle in. This didn't work for me either.
At this point, I'm willing to try anything. I'm not quite sure how to fix this issue. I think my next step is to either order a factory cable or make my own and try that, but if my bootloader is broke (truely broke) will that even work?
Please, if I should post this in another forum/place, just let me know. Any help appreciated!
I should also not that nothing comes up in my device manager. It does come up as a unrecognized USB bit goes away after telling me there was a malfunction (it tries to recognize it twice).
Please don't post the same question in multiple threads... especially ones that have been dead for 4 months. I've replied to the same question as a followup to your other post.

[Q] Kindle fire bricked, adb : device not found, help me

First, sorry for my english.
I have a Kindle Fire OS 6.2.1. I dont know why my Kindle didn't work with ADB driver.
Only one time it work when I used Kindle Fire Utility 0.9.1, then I run option 2 then 3. After that, my Kindle reboot and stop at logo's screen, and adb didn't recognize my Kindle anymore.
I tried install/uninstall, downloaded new driver, install Android SDK,.... but don't luck.
All method to unbrick need adb work well.
Help me fix this issue, please. I live in Asia and can't return my Kindle for Amazon.
first - have you read and done the tricks from kfu ?
Known Tricks
•If you end up stuck at the yellow triangle, in KF Utility select Boot Normal, wait for it to say <waiting for device> and then press and hold the power button 20 seconds until the fire turns off, then when its off turn it back on. This sometimes happens, I have yet to find a clean solution
•If you end up stuck with a yellow triangle, do not EVER unplug it. Leave it plugged in. Check the windows drivers to make sure it isnt showing as "kindle" again. Fastboot is different and can cause this.
Click to expand...
Click to collapse
second - don't use the drivers from kfu - do according:
http://forum.xda-developers.com/showpost.php?p=20855280&postcount=54
This helped me get out of a brick 4 times I hope it helps you-
http://forum.xda-developers.com/showpost.php?p=20421225&postcount=222
Just to be redundant this is not a 'brick'
Confirming the driver issue- gotta use diff drivers I restored my Win8 to the kfu .6 just to get adb working
Sent from my Amazon Kindle Fire
b63 said:
first - have you read and done the tricks from kfu ?
second - don't use the drivers from kfu - do according:
http://forum.xda-developers.com/showpost.php?p=20855280&postcount=54
Click to expand...
Click to collapse
The 2nd option help me out to get my kindle fire recognized.
Thanks.
On mine I booted it up to the firefirefire logo and right before the screen flickered I'm not sure if yours does that) I ran a command on the an adb shell command then re ran Kindle fire utilitity's taro installed and it fixed it!
I spent two weeks with a similar problem, finally have everything working. My biggest problem was a USB to micro USB cable that worked fine for charging, but seldom worked for communication between the Fire and my PC. Try another cable.
If your PC beeps when you insert the USB cable, then the cable is probably OK.
Next likely problem is that you don't have ADB installed properly. You can check this by typing adb help at the CMD prompt. (START, RUN, CMD, adb help) If you get a lengthy response, then ADB is installed OK. If you get an error msg, then you need to fix that. Google "How to Install ADB"
If ADB is OK, and you still can't see your Kindle, you probably haven't updated your PATH Variable properly. "How to Install ADB" should include instruction for doing that, but you need to be sure you enter the actual path that your have to the SDK Platform_Tools folder on your PC, not the one described in the video.
Once I managed to get these three thing all working at the same time, things started to fall into place. To most of the people on this forum, these things are probably obvious, but to an old geezer like me every step is a painful learning process.
Good luck

[Q] Black screen, plugged into PC, keeps disconnecting/reconnecting. Bricked to Hell?

Just like the title says. At first when I plugged my Kindle Fire in it showed up as the processor name. I installed the drivers by just using that hoping to get some sort of PC connection.
Im on Windows.
TWRP was messed up and wouldnt boot for me. (when screen worked.)
Had ICS beta. (When screenworked)
Would like to get back to stock.
Could anyone help me out?
maybe out of battery ? charge for an hour with the wall plug (pc loads very slowly)
some more information would be helpful:
what exactly have you done ?
os/bit of your computer ?
do you have newest kfu available ?
if yes please move and rename to c:\kfu (win7 64bit drivers will not install with spaces and it's easier to help cause in the tools folder are all necessary commands)
b63 said:
maybe out of battery ? charge for an hour with the wall plug (pc loads very slowly)
some more information would be helpful:
what exactly have you done ?
os/bit of your computer ?
do you have newest kfu available ?
if yes please move and rename to c:\kfu (win7 64bit drivers will not install with spaces and it's easier to help cause in the tools folder are all necessary commands)
Click to expand...
Click to collapse
Usually it charged through the USB port on my computer but currently I put it on the wall charger to see if that would be the problem.
Well the history is this: Rooted 6.2.1, installed ICS, but after messing with TWRP my Kindle Fire arrived at a point where ICS was the ONLY OS, no backup available and TWRP being stuck at the logo not proceeding. I used the KFU to try to install a new TWRP on it but I think that might of messed it up. Im not sure to be honest theres been a lot done on this and its been a week til I had time to resolve my issue.
Windows 7 64bit
EDIT: Btw the green light from the power button never comes on. Ill plug the device in and nothing will happen until I hold the power button down for a while.
It shows up in the device manager, but only for a second to be disconnected, then the cycle repeats constantly.
Bricked to hell....I got a chuckle out of that.... Good luck man, hope you can get it fixed.
Sent from my Kindle Fire using xda premium
Okay. So at this point you are unable to power the device on? Even after charging it off of the wall port? (PC charging my android devices never personally worked for me)
Also have you loaded a custom kernel on? And have you checked if ADB can recognise the device?
Sent from my Kindle Fire using xda premium
Ok, all you have to do if twrp is messed up is to reflash it in fastboot. You can never Really brick a device.... See if you have adb.
http://forum.xda-developers.com/showpost.php?p=21715022&postcount=9
Zomboogz said:
Okay. So at this point you are unable to power the device on? Even after charging it off of the wall port? (PC charging my android devices never personally worked for me)
Also have you loaded a custom kernel on? And have you checked if ADB can recognise the device?
Sent from my Kindle Fire using xda premium
Click to expand...
Click to collapse
Well I know its on cause how would the PC be able to recognize it? It keeps going on and off so I cant time it correctly or its just too fast I cant tell.
b63 said:
http://forum.xda-developers.com/showpost.php?p=21715022&postcount=9
Click to expand...
Click to collapse
Im going out to dinner but I will try that and let you know how it works after

[help] kindle fire stuck at yellow triangle/reboot loop

Hi, I've recently rooted my Kindle Fire device using KFU v9.3. After this, I noticed that FFF and TWRP weren't installed. So I used KFU to install FFF and it worked perfectly. I tried to install TWRP and it failed saying
"Oops… something went wrong with the download.
The recovery downloaded is not correct.
Please try the download again."
However, on the second try it worked up until a point where KFU said "Setting Normal bootmode" followed by "waiting for device...". This was when my kindle got stuck on the yellow triangle screen and my computer has not been able to recognize it since.
I have tried to install drivers via the install_drivers.bat file in KFU, however i get the error "install failed (Unsigned)" I tried to use Zombiepirates' Kindle Fire Unbrick Utility and selected "Stuck at logo" but it can't find the device.
Now when I plug my kindle into the computer it just keeps turning on and off and my computer doesn't recognize it.
I'm using a WIndows XP pc and I have access to a windows 7 one if needed.
Try this..
http://forum.xda-developers.com/showthread.php?t=1422832
Have you tried using KFU to change the bootmode back to normal despite your kindle not being detected? After you attempt to change the bootmode to normal perform a hard reset (hold the power button for 30 seconds) and your kindle should be detected. Hope this helps, worked for me for the same issue
I can't, whenever I use "install_drivers.bat" I get an error that says "Install failed (Unsigned)"
Do you know how I should go about fixing this?
BluesHawk said:
Have you tried using KFU to change the bootmode back to normal despite your kindle not being detected? After you attempt to change the bootmode to normal perform a hard reset (hold the power button for 30 seconds) and your kindle should be detected. Hope this helps, worked for me for the same issue
Click to expand...
Click to collapse
Yes I have. It says "waiting for device" and I did a hard reset to my Kindle but still it's "waiting for device" now my Kindle is just shutting on and off rapidly whenever it's plugged into the computer
Is windows blocking the driver? You're on XP right? Try this, then try installing the driver.
Right click on My Computer then select Properties to open System Properties.
In “System Properties” dialog box, select the Hardware tab.
Click on Driver Signing button.
Make sure "block" option isnt checked. That wouldn't let you install any uncertified drivers.
BllgpapaG said:
Yes I have. It says "waiting for device" and I did a hard reset to my Kindle but still it's "waiting for device" now my Kindle is just shutting on and off rapidly whenever it's plugged into the computer
Click to expand...
Click to collapse
The same thing is happening to me. My kindle is rebooting when plugged into the computer, KFU or KUU aren't able to do anything. I'm using Windows 7 but I can't bring up the drivers because the device isn't recognized by windows
any ideas on how to stop this rapid rebooting is much appreciated
Edit
a link to my post on a similar issue can be found here
MasterJoefus said:
The same thing is happening to me. My kindle is rebooting when plugged into the computer, KFU or KUU aren't able to do anything. I'm using Windows 7 but I can't bring up the drivers because the device isn't recognized by windows
any ideas on how to stop this rapid rebooting is much appreciated
Click to expand...
Click to collapse
Update your kindle fire driver with the file in the KFU directory.
Go into Device Manager, find the Kindle fire, update the driver and point it to the driver in the KFU directory. (KFU>drivers>kindle)
_Justin said:
Update your kindle fire driver with the file in the KFU directory.
Go into Device Manager, find the Kindle fire, update the driver and point it to the driver in the KFU directory. (KFU>drivers>kindle)
Click to expand...
Click to collapse
The kindle is not listed in the device manager because after the kindle reboots a few times while connected to the pc, windows stops adding it to the device manager. Is there any way to manually add it and add the drivers?
MasterJoefus said:
The kindle is not listed in the device manager because after the kindle reboots a few times while connected to the pc, windows stops adding it to the device manager. Is there any way to manually add it and add the drivers?
Click to expand...
Click to collapse
I don't know why it's doing that. Is it constantly rebooting? Try another USB port or PC.
from the op of kfu:
Known Tricks
•If you end up stuck at the yellow triangle, in KF Utility select Boot Normal, wait for it to say <waiting for device> and then press and hold the power button 20 seconds until the fire turns off, then when its off turn it back on. This sometimes happens, I have yet to find a clean solution
•If you end up stuck with a yellow triangle, do not EVER unplug it. Leave it plugged in. Check the windows drivers to make sure it isnt showing as "kindle" again. Fastboot is different and can cause this.
Click to expand...
Click to collapse
and from vashypooh - dev of kfu:
http://forum.xda-developers.com/showpost.php?p=20945694&postcount=506
about drivers:
http://forum.xda-developers.com/showpost.php?p=22342376&postcount=6
hope this helps ...
@b63
THANK YOU! Your post about drivers is the most direct and effective way to install drivers. I wish I could thank you a million times.
glad to help ...
please mark the subject of the topic (edit first post) with [Solved]
Kindle Fire in FFF Loop
I am also having the same issue as well. Tried running the KFU for unbricking and still nothing as my PC nor my laptop is able to recognize my KF. Not sure what to do. It is constantly just looping while connected via USB and if I disconnect it, it powers off.
Any help would be great.
sounds like empty battery
would try to charge it with the wall charger for some hours
if it turns on if you plug it to the wall charger try to power it off by holding the pwr button ~20sec till it turns off to allow charging
noob needs help with ice cream sandwitch gone wrong!!
Hey ya'll,
So I'm sure you're tired of noobs posting but I just need a little help. I rooted my kindle last night and then tried giving it ics 4. So, I wiped everything (as instructed) and before hand I added the cm09 file along with the gapps. Yet, when I downloaded and extracted these two files they came out as multiple files so I first extracted the files to my desktop. I then transferred the individual files to the root of my kindle. When trying to "install" them , the individual files(which cm09 and gapps had been comprised of ) popped up but I couldn't do anything with them (flash ,etc). So, then I tried condensing all the gapps files into one "gapps" folder and all the cmo9 files into one "cm09" folder and transfer it to the root. Same thing happened. What I think I should haev done is not extracted either and just have sent the unzipped files to the root of my kindle...woops...I am a dumb noob after all! So, now I'm stuck with my kindle and when I turn it on to "normal mode" (not the TWRP) the "kindlefire" insignia pops up at start up like normal but it just sits there like that. Any idea of what I should do and where I can get the files to do it so that I too can have the LIMITLESS POWER OF ICE CREAM!!?? MWAHAHAHAHA...really though..any help ?
would try to boot to twrp - tap mount and mount sdcard - copy the cm9 file to the root of sdcard as instructed - install it with twrp - that should do it
you can install the necessary gapps afterwards - if i remember right it is also described how to do in the op of cm9
i just wanted some help. I rooted my kindle fire and flashed everything had cm7 on it one point and wanted to try miui's rom. I did as instructed but its stuck on the fff screen. Ive also tried as b63 instructed. But every time i connect my kindle it shows up for a brief second and disappears. What do i do? Please help! thank you!
You are 100% correct.
b63 said:
sounds like empty battery
would try to charge it with the wall charger for some hours
if it turns on if you plug it to the wall charger try to power it off by holding the pwr button ~20sec till it turns off to allow charging
Click to expand...
Click to collapse
If the yellow triangle is flashing and the tablet turns of when you unplug it from your computer then the battery is totally dead. I figured that out after 7 hours of frustration!
Yea I had that same issue with mine. I connected it to its factory shipped charger and about an hour later it was turning on and staying on.
Sent from my Kindle Fire using Tapatalk

I closed the command prompt while installing TWRP. Please help me.

First off, I am very much an iOS person, so Android is very new to me. Bear with me.
My brother got a Kindle Fire today, and naturally I told him he should root it, etc. I rooted it and was installing TWRP 2.0 with Kindle Fire Utility. Unfortunately, silly me accidentally closed the CMD window, resulting in...bad things. It won't boot, the computer will not recognize a USB storage device, and it is stuck on the Kindle Fire logo. KFU does not see it either.
Please someone help. Bro will be pissed if I broke his Fire day one...
Uninstall/reinstall device drivers and try again.
Sent from my Amazon Kindle Fire using xda premium
soupmagnet said:
Uninstall/reinstall device drivers and try again.
Sent from my Amazon Kindle Fire using xda premium
Click to expand...
Click to collapse
How?
kona314 said:
How?
Click to expand...
Click to collapse
oh my
http://www.jayceooi.com/2011/12/13/how-to-install-kindle-fire-adb-usb-driver/
Sent from my Amazon Kindle Fire using xda premium
soupmagnet said:
oh my
snip
Sent from my Amazon Kindle Fire using xda premium
Click to expand...
Click to collapse
Yeah, I figured it out, I just came back to edit the post haha.
That did nothing.
OK so you've uninstalled and manually reinstalled your drivers, right?
Are you using KFU or just command prompt to change your bootmode?
Sent from my Amazon Kindle Fire using xda premium
soupmagnet said:
OK so you've uninstalled and manually reinstalled your drivers, right?
Are you using KFU or just command prompt to change your bootmode?
Sent from my Amazon Kindle Fire using xda premium
Click to expand...
Click to collapse
Neither one even recognize a Kindle.
OK, so command prompt it is.
Turn your Kindle off.
In your command prompt type (don't enter)...
fastboot devices
Plug your Kindle into the computer. It should turn itself on.
Wait about 3 seconds and hit enter. It should return a string of numbers.
Then type...
fastboot -i 0x1949 oem idme bootmode 4000
Then restart (hold power button for 30 sec.)
If you don't get a string of numbers it is usually indicative of a driver issue. In which case....Uninstall and manually reinstall your drivers and try again.
Sent from my Amazon Kindle Fire using xda premium
soupmagnet said:
OK, so command prompt it is.
Turn your Kindle off.
In your command prompt type (don't enter)...
fastboot devices
Plug your Kindle into the computer. It should turn itself on.
Wait about 3 seconds and hit enter. It should return a string of numbers.
Then type...
fastboot -i 0x1949 oem idme bootmode 4000
Then restart (hold power button for 30 sec.)
If you don't get a string of numbers it is usually indicative of a driver issue. In which case....Uninstall and manually reinstall your drivers and try again.
Sent from my Amazon Kindle Fire using xda premium
Click to expand...
Click to collapse
I did not get a string of numbers. I tried reinstalling the drivers earlier... Would it make a difference now? And does the fact that I'm using drivers from the KFU have anything to do with that?
Windows is a real pain sometimes when it comes to adb drivers. Try rebooting your computer and check to make sure your device manager says [Edit:] "Android ADB Interface"
Sent from my Amazon Kindle Fire using xda premium
Quick heads up, when you killed the command prompt in the middle of installing twrp 2.0 you probably just ended up leaving the kindle in fastboot mode (which is usually shown by getting stuck at the firefirefire bootloader) basically you need to plug your kindle into the computer and cd to where the adb is in your android folder like you did when you were installing twrp and punch in the command to change the boot mode back to 4000 (normal boot). In fastboot you won't get recognized by adb but when you punch in the command it will go to the kindle because fastboot is actually sort of like adb where there is a file called fastboot in the same directory on your computer that adb is in that lets you interface with your kf.
So basically plug the kindle it, cd to android/android-sdk/platform-tools/ and enter in:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
or
fastboot oem idme bootmode 4000
fastboot -i 0x18d1 reboot
or
fastboot -i 0x18d1 oem idme bootmode 4000
fastboot reboot
One of those should work. Don't worry about adb not recognizing the device, in fastboot mode you won't see it under adb. But the computer sees it regardless.
---------- Post added at 10:19 PM ---------- Previous post was at 10:09 PM ----------
It just occured to me that maybe you were only using the kfu and not the android sdk if not you should look into installing the android sdk and not rellying on the kfu, while it is useful these situations are easier to deal with when you have complete adb access through android sdk, google the android sdk and install it.
If "fastboot devices" doesn't recognize that a device is connected, no amount of other fastboot commands will work; in which case it's usually a driver issue.
Sent from my Amazon Kindle Fire using xda premium
In you command prompt when you type
dir
...do you see fastboot?
Sent from my Amazon Kindle Fire using xda premium
I tried a different computer...same issue.
The fastboot commands did nothing, stalled on "waiting for device."
soupmagnet said:
In you command prompt when you type
dir
...do you see fastboot?
Sent from my Amazon Kindle Fire using xda premium
Click to expand...
Click to collapse
I did, see above post.
Well the next thing for you to do is get a factory cable as that's the best way to unbrick a brick. And sorry I guess I missed the fastboot post in the thread, I had an issue where I got stuck in fastboot and the method I posted worked but I guess your issue is different than the one I had.
isaiahhhhh said:
Well the next thing for you to do is get a factory cable as that's the best way to unbrick a brick. And sorry I guess I missed the fastboot post in the thread, I had an issue where I got stuck in fastboot and the method I posted worked but I guess your issue is different than the one I had.
Click to expand...
Click to collapse
You're fine.
By factory cable do you mean a USB cable from Amazon? If so, that's what I'm using... How do I unbrick?
If I'm horribly wrong, please explain.
isaiahhhhh said:
Well the next thing for you to do is get a factory cable as that's the best way to unbrick a brick. And sorry I guess I missed the fastboot post in the thread, I had an issue where I got stuck in fastboot and the method I posted worked but I guess your issue is different than the one I had.
Click to expand...
Click to collapse
Even with a factory programming cable which will put you in fastboot mode anyway, if there is a problem that is keeping the device from being recognized in the first place, it wouldn't do you any good.
So let's stop and start all over with the basics and try to eliminate any possibility of mistakes.
First, get rid of KFU. Uninstall and delete BOTH the adb_usb.ini and android_winusb.inf drivers. Download and install Android SDK. Configure and and install the android and adb drivers that come with the SDK using the tutorial posted here. http://www.jayceooi.com/2011/12/13/how-to-install-kindle-fire-adb-usb-driver/
Sent from my Amazon Kindle Fire using xda premium
It's funny.. this is such a simple process, yet it stumps almost everyone on these boards.
It is simply a driver issue. But it is not something you can just explain to people bow to do. It has been my experiance that even when you give a step by step people will not follow it correctly.
However.. I will attempt to at least get your driver issue solved.
First.. open device manager, device manager can be accessed from windows 7 by clicking the start menu and typing device manager.
Once device manager is up, plug in the kindle, wait for device manager to show something. You will see , unknown device, android phone, kindle fire or something similar.
Next, find the folder you downloaded with the kindle fire drivers. They are just adb drivers, but you will need to know their location. If device manager does not show "adb composite device" then you need to do the next steps.
With the driver folder located, right click on the device in device manager associated with your kindle. Click properties, click update driver, click choose driver location manually, browse to that driver folder, here you will have to uncheck the box that says display compatible devices. You should see "android composite device" as an option. Select.it and continue the install.
If you did that correctly, you should now see the fire as an adb composite device in device manager. It will now take fastboot commands.
If when you plug.in your kindle, your hear the USB connect sound, your kindle.is.not.bricked , you just need to get the right driver on it, and that is all user error when it is not done right.
I will update this thread with some screenshots for you , and verifiy my steps. I'm writing this on my phone while in bed and I stilll need coffe
Sent from my ADR6425LVW using XDA
Serinety said:
It's funny.. this is such a simple process, yet it stumps almost everyone on these boards.
It is simply a driver issue. But it is not something you can just explain to people bow to do. It has been my experiance that even when you give a step by step people will not follow it correctly.
However.. I will attempt to at least get your driver issue solved.
First.. open device manager, device manager can be accessed from windows 7 by clicking the start menu and typing device manager.
Once device manager is up, plug in the kindle, wait for device manager to show something. You will see , unknown device, android phone, kindle fire or something similar.
Next, find the folder you downloaded with the kindle fire drivers. They are just adb drivers, but you will need to know their location. If device manager does not show "adb composite device" then you need to do the next steps.
With the driver folder located, right click on the device in device manager associated with your kindle. Click properties, click update driver, click choose driver location manually, browse to that driver folder, here you will have to uncheck the box that says display compatible devices. You should see "android composite device" as an option. Select.it and continue the install.
If you did that correctly, you should now see the fire as an adb composite device in device manager. It will now take fastboot commands.
If when you plug.in your kindle, your hear the USB connect sound, your kindle.is.not.bricked , you just need to get the right driver on it, and that is all user error when it is not done right.
I will update this thread with some screenshots for you , and verifiy my steps. I'm writing this on my phone while in bed and I stilll need coffe
Sent from my ADR6425LVW using XDA
Click to expand...
Click to collapse
Hmm... Windows tells me that it won't update the drivers because the ones I have are the same or better...

Categories

Resources