Related
I flashed this leaked rom (JVR) from Samfirmwares.com with ODIN with repartition over MIUI 1.7.29 - problems started after I wanted to go back. I turned the download mode on and I found out that it is active but the windows do not recognize the device (tried other devices). Once i turbned the device off it yould not be started again.
Unless I put the battery with les percentage into the device and put it on charger with power button pressed (then quickly disconnect the cable once the baterry charging animation shows up), it wont start. The same goes wirth 3e recovery.
The phone was not rooted, and it does not have CWM installed. I am without hope, Google, the greatest of all, did not offer me any kind of solution.
Is there any way how to root 2.3.4 SGS JVR without ODIN or CWM? So i could install CWM and flash CM7 or whatever else instead? THX.
You can use CF-root to root, or flash JVQ deodexed.
I don't realy understand your problem ...
I think your only other option would be super one click, but it requires windows.
Bootloader problem
flo2lacanau said:
You can use CF-root to root, or flash JVQ deodexed.
I don't realy understand your problem ...
Click to expand...
Click to collapse
The problem is, that the phone starts only when it is on charger. And when I try to enter 3e recovery it enters Force Upload by Key Pressing mode, that I dont know. THe download mode screen is ok, but the phone connects only as UNKNOWN DEVICE. I have no solution for this yet.
There is no way I could flash with odin since I have no USB connection to the phone. Bootloader is corrupted and USB does not initialize correctly.
All stock gingerbread firmwares come with new bootloaders. CM7 only supports Froyo bootloaders.
Since MIUI is based on CM7, you probably need to flash a stock Froyo with bootloaders before flashing MIUI again.
I can't flash anything
I cant flash anything. Recovery does not work and the USB connector on the device is not initialized by the device because of the bootloader is corrupted. I need to root the device with some APK so that I could install CW recovery but z4root does not work for me.
hearthcore said:
I cant flash anything. Recovery does not work and the USB connector on the device is not initialized by the device because of the bootloader is corrupted. I need to root the device with some APK so that I could install CW recovery but z4root does not work for me.
Click to expand...
Click to collapse
Have you tried to connect the phone with another pc?
EDIT: You need a signed zip, i think!
EDIT2: Heimdall?
Cannot flash
olivercervera said:
Have you tried to connect the phone with another pc?
EDIT: You need a signed zip, i think!
EDIT2: Heimdall?
Click to expand...
Click to collapse
Yes, I tried everything else, like another pc, other devices, other cables. The PC simply does not recognize the device. Ill have to wait until there is a new version of GingerBreak or any kind of APK based exploit. Then root the device from the inside and instal proper recovery, then flash the bootloader. Or else it will be a half-dead semi-zombie phone forever.
hearthcore said:
Yes, I tried everything else, like another pc, other devices, other cables. The PC simply does not recognize the device. Ill have to wait until there is a new version of GingerBreak or any kind of APK based exploit. Then root the device from the inside and instal proper recovery, then flash the bootloader. Or else it will be a half-dead semi-zombie phone forever.
Click to expand...
Click to collapse
And Heimdall? I never used it, but you can try if it recognizes the phone!
Do you have the SGS drivers installed?
i have had the same problem! just try to flash JVK (cause it have safe bootloaders...was the only rom that saved me). Pull out the battery and restart the phone directly in download mode...JVK is for gingerbread. For CM7 based rom find out what rom from froyo you need to install first, with safe bootloaders!
I cannot flash anything. I only have 3e recovery option, but it flashes only signed ZIP files.
I got same problem, phone starts only when charger or usb cable plugged in. sent back to samsung they mentioned its a hardware problem and fixed it. I was on official rom.
Sent from my GT-I9000 using XDA App
hearthcore said:
I cant flash anything. Recovery does not work and the USB connector on the device is not initialized by the device because of the bootloader is corrupted. I need to root the device with some APK so that I could install CW recovery but z4root does not work for me.
Click to expand...
Click to collapse
I have the same problem, but I made a mistake when I flash bootloader
If anybody have some advice, please help :crying:
zg_trotter said:
I have the same problem, but I made a mistake when I flash bootloader
If anybody have some advice, please help :crying:
Click to expand...
Click to collapse
you can get a rescue kit from My Android Collections and or a solution from My Android Solutions
Use only ROM and solution for your model and Wipe x3
But First powerdown, pull out Battery, SIM CARD, and EXT.SD card, press power button for a minute, than powerup without SIM and Ext.SD Card....
(Do remember to backup your contacts, data, images etc and also your EFS folder before flashing a ROM and make sure you have more than 50% battery charge before you attempt any sort of flashing.)
This Thread Is For Them Who Bricked There Phones
Don't start a new thread for your bricked phone & post here.
We will help you with every possible solutions.
Here are some quick tips :
(Here I'll use the terms like Download-Mode & Recovery-Mode, If you dont know what are they please click here. There "BOOT to RECOVERY" & "BOOT to BOOTLOADER" means how to enter into Recovery-Mode & Download-Mode respectively.)
A Bricked Phone May Have One or More (Below Problems) :
1. Booting to the ROM(Android) not possible.
2. Booting to the Recovery-Mode not possible.
3. Black screen or Bootloop(Repeated Restarting of Phone at Boot Animation or Samsung Galaxy Y Logo).
Possible Solutions :
(Remember there'll be data loss using these solutions so always try to keep a backup)
1. If you can still enter into Recovery-Mode
(a). Try to clear Data & Cache then check.
(b). Try Installing a Custom ROM using CWM(ClockWorkMod Recovery) & check.
(For Custom ROM & CWM Visit here.)
2. If Recovery-Mode didn't helped Enter into Download-Mode & flash an odin supported stock rom(using ODIN 1.84 or 1.85) from Doky73's Thread(Flashing Guide in 2nd post).
*You can inform me, if anything left out.
Note :
1. I'll be not held responsible for anything that happens to your phone.
2. Before posting try to search for similar type problems out there & try the solution, if that doesn't solve your problem then post here.
Make this a sticky.. there are many users who say that their phone is bricked
help! bricked SGY
galaxy y bricked
i bricked my sgy last 3 weeks.
here's what i did.
-installed creedsix rom.
-installed UOT kitchen Themes.
-wipe data
problem
-stuck in bootlogo
-softbricked.
-cant go to recovery mode
-flashed too many times, still stuck in bootloop
i flashed at least 20 times, with different firmwares.
but still no luck, still boot lop.
my professor said something about secondary bootloader that might help. but i had definitely no idea what it is.
i asked some techies on the mall, and they said that this phone must undergo the JTAG process. but it cost $20.
help me. thanks.
jmpotter said:
galaxy y bricked
i bricked my sgy last 3 weeks.
here's what i did.
-installed creedsix rom.
-installed UOT kitchen Themes.
-wipe data
problem
-stuck in bootlogo
-softbricked.
-cant go to recovery mode
-flashed too many times, still stuck in bootloop
i flashed at least 20 times, with different firmwares.
but still no luck, still boot lop.
my professor said something about secondary bootloader that might help. but i had definitely no idea what it is.
i asked some techies on the mall, and they said that this phone must undergo the JTAG process. but it cost $20.
help me. thanks.
Click to expand...
Click to collapse
can you go to download mode??
(try pressing volume down+ home button + power button all at the same time)
if it still can, then your SGY is still good
go to this ---> thread
and just flash your country's firmware
From where you got the firmwares.... How you flashed...
Ever tried re partitioning.... Ever flashed boot loader....
For info... Jtag or boundary-scan is used for testing & servicing high technology electronic boards...
Sent from my GT-S5360 using Tapatalk 2
Millan.SIS said:
From where you got the firmwares.... How you flashed...
Ever tried re partitioning.... Ever flashed boot loader....
For info... Jtag or boundary-scan is used for testing & servicing high technology electronic boards...
Sent from my GT-S5360 using Tapatalk 2
Click to expand...
Click to collapse
just for info, jtag will not fix the problem. IT IS SCANNING.. like trouble shooting.
that only means that those technicians are pretending to be well educated but the truth is that they only wanted to get some cash out of your pocket.
static28 said:
just for info, jtag will not fix the problem. IT IS SCANNING.. like trouble shooting.
that only means that those technicians are pretending to be well educated but the truth is that they only wanted to get some cash out of your pocket.
Click to expand...
Click to collapse
ya, that's what those wannabees really do..
Sent from my GT-S5360 using Tapatalk 2
this one will a little bit off topic...what is creedsix?is it a rom for SGY?
if the phone still can boot that means everything is fine. pull out the battery, wait 10 seconds, reinsert the battery, do three magic combo button, you'll enter recovery mode. don't worry about our bootloader. our bootloader is stored in different partition thus installing any custom rom won't affect our bootloader. as far as i know, there is only one person who have messed up with bootloader and got an ultimate hard brick.
kurotsugi said:
this one will a little bit off topic...what is creedsix?is it a rom for SGY?
if the phone still can boot that means everything is fine. pull out the battery, wait 10 seconds, reinsert the battery, do three magic combo button, you'll enter recovery mode. don't worry about our bootloader. our bootloader is stored in different partition thus installing any custom rom won't affect our bootloader. as far as i know, there is only one person who have messed up with bootloader and got an ultimate hard brick.
Click to expand...
Click to collapse
Really its great thread ........ Many many thanks for helping ppl ......
is it possible repair hard brick ..... what is hard brick... if device hard brick device gos life time dead ??
Sent from my GT-S6102 using xda premium
a hard brick is when our device doesn't respond to power button.
the guy that I've mentioned above is doky73. he accidentally flash a bootloader for sgs2 into his sgy. last time he said that he send his sgy to samsung service center and buy a new one. I'm not sure if samsung has revived his sgy.
edit: I didn't to offend him but I think I've mispelled doky's username. edited.
manoranjan2050 said:
Really its great thread ........ Many many thanks for helping ppl ......
is it possible repair hard brick ..... what is hard brick... if device hard brick device gos life time dead ??
Sent from my GT-S6102 using xda premium
Click to expand...
Click to collapse
whatever It may be... You should never mess up with bootloaders, if you don't actually know what's there significance...
Brief description on android starting process :
pbl(primary boot loader "boot.bin") executes first and then it executes sbl ...
Sbl(secondary boot loader "sbl.bin") is responsible for responding to combos...download mode.. Intercepting odin commands..... booting system...booting kernel.... Charging your battery while switch off... Etc etc
Harm anyone of them... And Your phone goes into lifetime hibernation, Hard-bricked.
Sent from my GT-S5360 using Tapatalk 2
thanks for the big info friend...... so hard bricl is mot repairble ......
Sent from my GT-S6102 using xda premium
my device might be bricked, can you please help me out
Hi to all, it's only my second post but i have a major problem with my samsung s-5360. it's won't boot anymore, but it can enter cmw and recovery. This is what i did wrong i believe. At first i installed morocs 1.8 kernel on creed fusion version 3.1 and it wouldn't boot anymore, so i ended up using a back-up i made before with cmw. And it worked well and phone was booting again and was on stock again. ( because back-up was made with stock-version obviously )
Then i thought: well let's try repensis noob version. And installed it and there was also an update 2 and installed it over it as well before booting the os, maybe this is what i did wrong dunno .. But afterwards it didn't boot anymore and whatever i tried, restoring one of the 3 images i made, or using one of the roms posted here like Creed fusion 3.1 rom or Aurora 2 nor Chobits didn't work.
I also tried reverting to stock with odin 1.85 but when i connected my phone via usb to the pc, odin didn't see my phone. ( after selecting the 3 tar files in odin ) Maybe i'm doing wrong something there.
What i also have to add is that when doing factory wipe in recovery it says formatted E: but unable to format E:\dev10 and dev11. clearing cache is no problem and also cleared dalvik cache. Can you please help me out ? I know, it sounds very noobish but well, i have to face it because can't do it myself without help anymore it seems ... Thanx a lot in advance.
please make sure that you've installed the driver and plug the usb to computer only on download mode when flash with odin. dev10 and dev11 are the partition for data and cache. that error means something was wrong with your recovery mode. you'll need to install a fresh stock rom with odin.
kurotsugi said:
please make sure that you've installed the driver and plug the usb to computer only on download mode when flash with odin. dev10 and dev11 are the partition for data and cache. that error means something was wrong with your recovery mode. you'll need to install a fresh stock rom with odin.
Click to expand...
Click to collapse
Thanx a lot for responding ! I only used kies for connecting my phone because i couldn't find a driver for it, and had to disconnect it, but i will search for it again now and hopefully it will work now. i have to go now and return back in three hours. i'm very curious ! i'll come back in a couple of hours and gonna tell if it worked out of course
kurotsugi said:
a hard brick is when our device doesn't respond to power button.
the guy that I've mentioned above is doky77. he accidentally flash a bootloader for sgs2 into his sgy. last time he said that he send his sgy to samsung service center and buy a new one. I'm not sure if samsung has revived his sgy.
Click to expand...
Click to collapse
to be precise: the guy was Doky73...
I was playing with different revisions of SBLs because on SGS2 some old SBL gives the possibility to reset custom bin counter via JIG. At a given point accidentally browsed SGS2 bootloader instead of SGY one...
But I did perfect job, the service center wasn't able to detect the cause of bricking, but they recovered my phone under warranty. (I think they're not reading this forum )
Doky73 said:
to be precise: the guy was Doky73...
I was playing with different revisions of SBLs because on SGS2 some old SBL gives the possibility to reset custom bin counter via JIG. At a given point accidentally browsed SGS2 bootloader instead of SGY one...
But I did perfect job, the service center wasn't able to detect the cause of bricking, but they recovered my phone under warranty. (I think they're not reading this forum )
Click to expand...
Click to collapse
Thanks friend.............
if i install some custom rom custom kernel via odin or CWN its gos to hard brick ???
in odin re-partition option for why ............ its disbl by default if i enable it wats problem........
dear friend if u have any odin full tutorial /guide /ref please provide me for learn syep by step one by one option or problem......
ops...my mistake. I guess I'm too sleepy when was typing your name. I'll edit it. sorry.
manoranjan2050 said:
Thanks friend.............
if i install some custom rom custom kernel via odin or CWN its gos to hard brick ???
in odin re-partition option for why ............ its disbl by default if i enable it wats problem........
dear friend if u have any odin full tutorial /guide /ref please provide me for learn syep by step one by one option or problem......
Click to expand...
Click to collapse
if u flash something through odin or cwm then you wouldnt hard brick ur phone.. it would be just a temporary brick which can be easily revived... i dont know abt that partioning thing
Sent from my GT-S5360 using XDA
kurotsugi said:
please make sure that you've installed the driver and plug the usb to computer only on download mode when flash with odin. dev10 and dev11 are the partition for data and cache. that error means something was wrong with your recovery mode. you'll need to install a fresh stock rom with odin.
Click to expand...
Click to collapse
Hi, there i am and sry for disturbing you again or someone else but i managed to install a non kies usb driver and i'm flashing thru odin 1.85 right now but i'm stuck at BcmCP.img for over an hour . Is it because i forgot to remove the sd card ? I only removed the sim and is it safe to stop the process and start over again or should i wait ?
---------- Post added at 02:35 AM ---------- Previous post was at 01:47 AM ----------
mickeyindahouse said:
Hi, there i am and sry for disturbing you again or someone else but i managed to install a non kies usb driver and i'm flashing thru odin 1.85 right now but i'm stuck at BcmCP.img for over an hour . Is it because i forgot to remove the sd card ? I only removed the sim and is it safe to stop the process and start over again or should i wait ?
Click to expand...
Click to collapse
Well after trying this proces for the 5th time i finally managed to go to stock rom and it only lasted a couple of minutes Of course thanx to doky73 who made all this possible ! So i unbricked it for the second time i guess
I did a full wipe and turns to me in recovery and recovery hangs me nothing can be done I do not want to turn to choose, the total crashes
I 4ext Recovery v 1.0.0.4 RC3
Any ideas a little help
abra-kadabra said:
I did a full wipe and turns to me in recovery and recovery hangs me nothing can be done I do not want to turn to choose, the total crashes
I 4ext Recovery v 1.0.0.4 RC3
Any ideas a little help
Click to expand...
Click to collapse
Ok...I have to say that I got just 1% of what u said. But I guess that u are stuck with just custom recovery...if you were running a custom rom and u did a full wipe then u don´t have rom anymore. Get a rom to your sdcard and reflash...or just restore a nandroid backup.
In recovery mode, you can not do anything hung up and you can not select anything
I don't know, maybe if he tries flashing the latest 4ext? However, not sure how to get that done.
Before doing that, pull the battery, wait 5 minutes and see if it works.
Sent from a dream.
I did flash recovery and was able to upload a cool rom but does not work Is it possible to feel that he sat down but I do not know why Do something with the rom?
I have uploaded rom stopped working and touch and buttons at the bottom
Someone has an idea ?
abra-kadabra said:
I have uploaded rom stopped working and touch and buttons at the bottom
Someone has an idea ?
Click to expand...
Click to collapse
It is really hard to follow you. Many people in here are non native english talkers, but if knowledge of grammar is missing, try it a different way:
Break the things into small pieces and explain in simple words. Nobody will blame anyone for that.
1) Did you root and s-off /eng-off your phone?
2) Did you install a custom recovery system?
3) If yes, which one?
Then:
1) Which ROM did you install?
2) Did you read the flash procedures from that ROM first?
3) Did you follow that instructions in matters of
3a) - Needed Recovery Manager Version
3b) - Needed to run before wipe scripts
Then:
Did you download the right scripts and
1) checke their SHA/MD5 checksum?
2) Flashed them onto the sd-card
3) called them in the proposed followup from the ROMs description in your recovery?
So, if you can answer the list above in simple words people might be able to help you. If not me, somebody else will for sure.
Best regards
Astralix
abra-kadabra said:
I have uploaded rom stopped working and touch and buttons at the bottom
Someone has an idea ?
Click to expand...
Click to collapse
Try a different sdcard....that might be the issue. If the problem persists then may be a hardware problem. Try to get back to stock and send the phone to a service centre.
Okay, I've searched the forum for several hours but there's just too much here to make sense of.
My phone is a SM-G900W8 brought home June 19 this year.
Stock Lollipop 5.0 pre-installed.
Code:
Baseband version: G900W8VLU1BOC1
Kernel version: 3.4.0-4100894
Build number: LRX21T.G900W8VLU1BOC1
SE for Android status: Enforcing, SEPF_SM-G900W8_5.0_0002
KNOX version: 2.3
Rooted using CF-Auto-Root (this file), Custom recovery is Philz Touch 6.57.8 klte.
Both of these were in place early on and haven't caused any problems.
Everything was working perfectly fine until last night, when I tried this trick (in first post), rebooted, and now I'm stuck at the splash screen.
Nothing gets me out except a battery pull.
I've tried:
Button combo volup - home - power to go to recovery; this does nothing from the splash screen (actually even pressing and holding down power does nothing), and after a battery pull it won't boot into recovery either.
Booting into download mode (success! yay!) and using Odin to re-flash Philz recovery. Reboot doesn't go into recovery, as stated above.
Just waiting, at various points in the process (while in splash screen, while turned off) to give a chance for things to happen if they just needed time.
So now I'm able to get into download mode and use Odin but from there I don't know what to do next. Flash the bootloader? Okay, but there are so many links...which one do I use? Of all the specs I've gathered, why didn't I find that out?
Can somebody help me please?
[EDIT: Solution and links, for SM-G900W8 users who might be looking for help]
I finally managed to boot into recovery by leaving the USB cable connected to the computer while pressing volup+home+power, a last-ditch trick found in deanr1977's very helpful thread "Read before flashing a Rom (Tips for new & old)"
Links to the firmware for this specific model can be found here, or if you just need a piece:
G900W8_OC1_Stock_Partitions.tar.md5
G900W8_OC1_100%_Stock_Rooted_ROM.zip
Stock_G900W8_VLU1BOC1_Kernel.zip
G900W8-LP-VLU1BOC1-MODEM.tar.md5
PushyPhoenix said:
Okay, I've searched the forum for several hours but there's just too much here to make sense of.
My phone is a SM-G900W8 brought home June 19 this year.
Stock Lollipop 5.0 pre-installed.
Code:
Baseband version: G900W8VLU1BOC1
Kernel version: 3.4.0-4100894
Build number: LRX21T.G900W8VLU1BOC1
SE for Android status: Enforcing, SEPF_SM-G900W8_5.0_0002
KNOX version: 2.3
Rooted using CF-Auto-Root (this file), Custom recovery is Philz Touch 6.57.8 klte.
Both of these were in place early on and haven't caused any problems.
Everything was working perfectly fine until last night, when I tried this trick (in first post), rebooted, and now I'm stuck at the splash screen.
Nothing gets me out except a battery pull.
I've tried:
Button combo volup - home - power to go to recovery; this does nothing from the splash screen (actually even pressing and holding down power does nothing), and after a battery pull it won't boot into recovery either.
Booting into download mode (success! yay!) and using Odin to re-flash Philz recovery. Reboot doesn't go into recovery, as stated above.
Just waiting, at various points in the process (while in splash screen, while turned off) to give a chance for things to happen if they just needed time.
So now I'm able to get into download mode and use Odin but from there I don't know what to do next. Flash the bootloader? Okay, but there are so many links...which one do I use? Of all the specs I've gathered, why didn't I find that out?
Can somebody help me please?
Click to expand...
Click to collapse
factory reset. Then flash stock rom. if you cant boot into recovery try the latest twrp. It works if its still not working then flash stock firmware from SAMMOBILE with odin. it will work then
Thanks for the reply. The problem I'm having is knowing where to download the files I need to flash - because there are so many threads here for so many different models of this phone. Believe me, I've looked, and keep turning up everything BUT W8
I'm tired and frustrated and need my phone functional - can you point me to a post or a thread with the latest version of TWRP that I can flash with Odin?
[edit] Sorry about that - I found the thread. I'll give that a shot and see what happens.
PushyPhoenix said:
Thanks for the reply. The problem I'm having is knowing where to download the files I need to flash - because there are so many threads here for so many different models of this phone. Believe me, I've looked, and keep turning up everything BUT W8
I'm tired and frustrated and need my phone functional - can you point me to a post or a thread with the latest version of TWRP that I can flash with Odin?
Click to expand...
Click to collapse
EDIT: THESE TOOLS ARE FOR 900F MODEL
Latest twrp from https://twrp.me/
Philz recovery from https://mega.co.nz/#!oVNz0T6C!VII47M...MpQIN2b-PEUYN8
Best Stock firmware 5.0 BTU from http://www.sammobile.com/firmwares/download/44413/G900FXXU1BOC7_G900FOXA1BOC7_BTU/
Enter download mode and Flash either one of the recoveries and Clear dalvik cache, clear cache, format system, format data and then factory reset. After that boot into odin mode directly and flash the Stock Firmware.
note: in Odin uncheck "auto reebot option" and after flashing recovery when the odin shows its done wait 1 minute disconnect usb and pull out battery then turn it on if your phone says "Recovery is seandroid enforcing" wait for 3-4 seconds it will go away and recovery will boot up.
dork997 said:
Best Stock firmware 5.0 BTU from http://www.sammobile.com/firmwares/download/44413/G900FXXU1BOC7_G900FOXA1BOC7_BTU/
Click to expand...
Click to collapse
Now, I just want to check: this is for the G900F; will it make a huge difference to my phone? Can I restore my data directly from the backup? I thought what I needed is the exact stock rom that was installed on this phone when I got it so I've been looking everywhere for the G900W8 firmware. I do intend to play with tweaked ROMs in future, but today's not that day.
Finally managed to boot into recovery after flashing TWRP - read a tip somewhere about doing the keypresses while connected to PC via USB. Currently running a nandroid backup before moving on to all the wiping/formatting steps - at least then if something else goes wrong I've got the latest data. :victory:
PushyPhoenix said:
Now, I just want to check: this is for the G900F; will it make a huge difference to my phone? Can I restore my data directly from the backup? I thought what I needed is the exact stock rom that was installed on this phone when I got it so I've been looking everywhere for the G900W8 firmware. I do intend to play with tweaked ROMs in future, but today's not that day.
Finally managed to boot into recovery after flashing TWRP - read a tip somewhere about doing the keypresses while connected to PC via USB. Currently running a nandroid backup before moving on to all the wiping/formatting steps - at least then if something else goes wrong I've got the latest data. :victory:
Click to expand...
Click to collapse
i am sorry the tools i mentioned are for 900f model. Here http://www.sammobile.com/firmwares/database/SM-G900W8/ you can find firmware for G900W8. Just factory reset format dalvik cache, cache , data and system and flash your stock firmware in recovery. There are many different firmwares available with the exact bootloader and modem but they are carrier specific. I don't know which carrier you are on (if any) so just go through the list and download the firmware you were on, flash it. I will highly recommend you to backup your EFS and modem folder aswell just incase anything goes wrong and u flash the wrong firmware.
Oh! Oh! I found it! The stock ROM, as well as the kernel and the modem! So, next question - should I flash all three or just the ROM?
(God I feel like an amateur right now...Thanks so much for helping me out here dork997. :highfive: )
PushyPhoenix said:
Oh! Oh! I found it! The stock ROM, as well as the kernel and the modem! So, next question - should I flash all three or just the ROM?
(God I feel like an amateur right now...Thanks so much for helping me out here dork997. :highfive: )
Click to expand...
Click to collapse
no prb, Okay if you download the rom from sammobile it should be in a .zip format extract it once and it will give you a .tar.md5 file which you have to flash in odin (this file has bootloader+firmware+modem) if you have 7zip or other such programs it will give you option to re-extract the .tar.md5 file but you dont need to do that just extract the downloaded zip once. and flash it in odin (make sure you factory reset and do the formating steps before flashing it....flashing rom over an old rom has caused some issues for me in the past so i always factory reset before but people also flash without factory reset or formating, choice is urs.
And I believe you've just answered my question. I'll hold off on flashing kernel and modem but I did back up everything, just in case. Wiping/formatting now; crossing fingers that things will go fine from here.
(My carrier is in my userinfo under my name, btw. )
Edit 'cause we keep posting at the same time: Hells yeah, I know how to flash, I've done it tons of times, just never run into this problem or had a device with so many variants so I'm just not used to asking so many questions, is all. I sincerely appreciate you guiding me through, and hope this will help others with this device in the future.
PushyPhoenix said:
And I believe you've just answered my question. I'll hold off on flashing kernel and modem but I did back up everything, just in case. Wiping/formatting now; crossing fingers that things will go fine from here.
(My carrier is in my userinfo under my name, btw. )
Edit 'cause we keep posting at the same time: Hells yeah, I know how to flash, I've done it tons of times, just never run into this problem or had a device with so many variants so I'm just not used to asking so many questions, is all. I sincerely appreciate you guiding me through, and hope this will help others with this device in the future.
Click to expand...
Click to collapse
cheers, if it does help you just try to give it back to the community.....i ve had similar issues and people here on xda helped me out. So i am doing the same.
FYI - It worked like a charm and now Lexie (I name my phones ) is up and running again almost like nothing happened. Thank goodness!
In case anyone else winds up needing them, I'm adding links to the stock firmware I downloaded.
Hi folks,
i have had many devices and virtually customized every one. Now i have really done it, i bricked my phone.
I did happily flash the new march updates for the 910F, some dr. ketan, just the usal stuff. However, now my phone boot loops in and out recovery. To be precise, it starts after successfully flashing with odin (does not matter if repartition with pid files or full nand erase...):
- it tries to enter recovery (blue text at the top)
- it fails (nothing happens), then it goes black, it vibrates two times and
- restarts with trying to enter recovery (endless loop)
No getting out. Removing battery and starting normal does not work.
Download mode and flashing via Odin and Kies "does" work, but changes nothing....
Does anyone have ever had similiar issues and or fixed this?
All thoughts are welcome.
Greetings from germany...
rionline said:
Hi folks,
i have had many devices and virtually customized every one. Now i have really done it, i bricked my phone.
I did happily flash the new march updates for the 910F, some dr. ketan, just the usal stuff. However, now my phone boot loops in and out recovery. To be precise, it starts after successfully flashing with odin (does not matter if repartition with pid files or full nand erase...):
- it tries to enter recovery (blue text at the top)
- it fails (nothing happens), then it goes black, it vibrates two times and
- restarts with trying to enter recovery (endless loop)
No getting out. Removing battery and starting normal does not work.
Download mode and flashing via Odin and Kies "does" work, but changes nothing....
Does anyone have ever had similiar issues and or fixed this?
All thoughts are welcome.
Greetings from germany...
Click to expand...
Click to collapse
try to flash only the stock recovery.
If it fails, flash the last stock with pit file + factory reset on recovey, if wou're again in bootloop
I did the same thing on my note 10.1
"your partition is corrupt. Would you like to factory reset your device?"
it is still here in bootloop..
Rajada said:
try to flash only the stock recovery.
If it fails, flash the last stock with pit file + factory reset on recovey, if wou're again in bootloop
Click to expand...
Click to collapse
Do you have a recent stock recovery flashible with odin or do you know where to find?
I did flash the recent stock with pit files/repartitioning,...does not help.
iRoNX said:
I did the same thing on my note 10.1
"your partition is corrupt. Would you like to factory reset your device?"
it is still here in bootloop..
Click to expand...
Click to collapse
How do you know the partition is corrupt? I think i already did a factory reset by repartitioning with the pit file. Corrupt partitions i tried to fix by nand erase in combination with repartitioning... this did not help.
I have the same problem, only problem I got some text with red+blue+yellow color, what I did was flash a stock ROM ( SAME ROM I HAD BEFORE ROOT FAIL) and it worked (like)
rionline said:
Do you have a recent stock recovery flashible with odin or do you know where to find?
I did flash the recent stock with pit files/repartitioning,...does not help.
Click to expand...
Click to collapse
any flagship Samsung is bricked if you can get into download mode.
if you want to try, above you have the recovery from the last S1CPC1, flash it at odin:
Rajada said:
any flagship Samsung is bricked if you can get into download mode.
if you want to try, above you have the recovery from the last S1CPC1, flash it at odin:
Click to expand...
Click to collapse
thank you very much. i do not understand your first sentence......btw. i can get into download mode...(just if you meant "can not")
Update: I have virtually flashed every rom > 5.0. No success, no difference. Everytime the odin flash procedure is successful (in all variants, with pit, with nand erase, etc...), but the phone loops everything (normal start, recovery) besides the bootloader.
only new thing i noticed: allthough binary status is official, the device status is and stays custom not matter what i flash.
anyone? anything?
Did you try to flash the stock recovery yet?
Also, what did you exactly flash to cause this?
sunniebeta said:
Did you try to flash the stock recovery yet?
Also, what did you exactly flash to cause this?
Click to expand...
Click to collapse
yes i tried stock recovery already. not sure what caused this. i do remember that i had some problems with 4.8 debloated and then i wanted to flash the hole corresponding stock package as clean base. somewhere in the middle this happenend. i am not quite sure, but maybe, maybe flashed cf-autoroot to this march update. but i am not sure if this was before, after or initially.
however,...what really bothers me, is that there is absolutely no indiciation for an error during the flash process. odin and kies, everything completes just fine, just booting does not work. that's why i fear, that this is just an ugly coincident and the problem is caused by some failing hardware.
maybe and immensly undclocked kernel (odin flashable) could start my phone. because something is still working, when the bootloader and the nand writing is working just fine.
does anybody know how to get a really granpa speedy kernel, or how to make it?
rionline said:
Hi folks,
i have had many devices and virtually customized every one. Now i have really done it, i bricked my phone.
I did happily flash the new march updates for the 910F, some dr. ketan, just the usal stuff. However, now my phone boot loops in and out recovery. To be precise, it starts after successfully flashing with odin (does not matter if repartition with pid files or full nand erase...):
- it tries to enter recovery (blue text at the top)
- it fails (nothing happens), then it goes black, it vibrates two times and
- restarts with trying to enter recovery (endless loop)
No getting out. Removing battery and starting normal does not work.
Download mode and flashing via Odin and Kies "does" work, but changes nothing....
Does anyone have ever had similiar issues and or fixed this?
All thoughts are welcome.
Greetings from germany...
Click to expand...
Click to collapse
Used to happen to me all the time. What I used to do was, after flashing the rom, connected it again to odin, flashed the cwm recovery 5-6 times and then used to give it a try. Also ,after trying this, flash the bootloader-modem file and pretty sure your phone will boot(This is optional)
rionline said:
Hi folks,
i have had many devices and virtually customized every one. Now i have really done it, i bricked my phone.
I did happily flash the new march updates for the 910F, some dr. ketan, just the usal stuff. However, now my phone boot loops in and out recovery. To be precise, it starts after successfully flashing with odin (does not matter if repartition with pid files or full nand erase...):
- it tries to enter recovery (blue text at the top)
- it fails (nothing happens), then it goes black, it vibrates two times and
- restarts with trying to enter recovery (endless loop)
No getting out. Removing battery and starting normal does not work.
Download mode and flashing via Odin and Kies "does" work, but changes nothing....
Does anyone have ever had similiar issues and or fixed this?
All thoughts are welcome.
Greetings from germany...
Click to expand...
Click to collapse
Greetings from Hamburg ☺
I was having also huge bug with dr.ketan rom at first was working flawlessly and 1 month later my phone wouldn't charge at all or recognise any charging cable.
Good thing is you can enter download mode (odin )
That means your phone is only soft bricked.
Flash SM-910F pit file + Latest stock firmware in odin mode all together in 1 flashing process...dont forget to mark repatriation in odin when using pit file.
When you got pass on odin and phone reboot and you see Samsung logo...fast take battery out and wait 1 min , put battery back and hold combo to enter stock recovery and do factory reset.
Good luck :fingers-crossed:
android freek said:
Greetings from Hamburg
I was having also huge bug with dr.ketan rom at first was working flawlessly and 1 month later my phone wouldn't charge at all or recognise any charging cable.
Good thing is you can enter download mode (odin )
That means your phone is only soft bricked.
Flash SM-910F pit file + Latest stock firmware in odin mode all together in 1 flashing process...dont forget to mark repatriation in odin when using pit file.
When you got pass on odin and phone reboot and you see Samsung logo...fast take battery out and wait 1 min , put battery back and hold combo to enter stock recovery and do factory reset.
Good luck :fingers-crossed:
Click to expand...
Click to collapse
Thanks guys. I tried yesterday some stuff, nothing was working and i finally got it dead as a stone! Nothing was working anymore. However, i took it to the samsung service center. They were irritated, that they can't get it on at all! ... However, i am curious, how they handle it and how much they want for a repair attempt/or replacement.
Just for info. I did all the things you proposed. Nothing worked. I think this was just a coincidental hardware failing. If you flash all the time, there is a chance that you do it, while something is dying!?
i keep you updated! Thanks for now...
Corrupted eMMC? Probably! Please let us know what the service centre said ultimately and how much they charged you.
ithehappy said:
Corrupted eMMC? Probably! Please let us know what the service centre said ultimately and how much they charged you.
Click to expand...
Click to collapse
So i am back with a fresh note 4 mainboard. they changed it no questions asked, no fee, no problems. i like!