I'm starting to have real problems with my USB plug. At first it would drop charger plugs when it was on the wall, so I put it upside down. But now I can't connect to the PC all the time either. I have to jiggle the plug a bit or even breathe down in it (the moist makes the connection better). Has anybody else had that problem and fixed it in any way? I suppose the plug is soldered on in such a way that it has to go to a workshop, right?
i strongly suggest you to send it for repair or resolder the base of the connection(this is user servicable provided you have some soldering skills) so it doesnt wiggle. i'd probly even suggest to hotglue the plug but before you do so make sure the plug is sitted properly and it does sync
the same thing happened to me and with a bit of jiggle the plug broke off and now its permenently damaged(ie it will never sync via USB again) so far with self repair i only manage to make it charge
i got no idea how to reattach a 10pin mini USB plug to my board and some of the copper tracks looks damaged which means if i send it to the shops, its a $500 repair and a board swap
I didn't buy the HTC extended battery but one from amazon sold by Karen Deals. Link is below
http://www.amazon.com/gp/product/B0..._m=ATVPDKIKX0DER&pf_rd_r=0NVM3EA1B2VE9HN3AKMA
Battery
Model No: cs-ht8585xl
Part No: 35h000128-00m, ba s400
Rating: 3.7v 2400mah
Lithium Ion
Induction Unit
Palm Pixi charging back with Palm touchstone charging dock
Operating System
Shubcraft 1.4d
Video:
Images are attached below!
Induction charging has the same charging speed as plugging it into a wall outlet. Very fast!
Sidenote:
I tried using a multimeter with the 3 contacts located under the battery and could not get it to register anything (with and without the charger plugged in). I then tried shooting 5v through it using 6 different combination (2 plugs for 3 contacts) and still couldn't get anything. If anyone knows a way to use these 3 contacts for charging please leave feedback. Also if anyone can find a minature microusb male connection that'd be great.
Well done, it's a really nice mod!
The 2400 mAh is a bit too bulky for me, though the extended uptime must be awesome. I'd even consider something similar, were it not that you're using the microusb to charge. If only you could connect it straight to the battery, would be so much more convenient. It'd still work in for instance car kits and attached to a pc.
Never the less, well done.
Looks great, i would try this myself but i cant stand the bulk of extended batteries and the stock metal back would almost defiantly interfere with the current. Where did you get the decal from?
Angelusz said:
Well done, it's a really nice mod!
The 2400 mAh is a bit too bulky for me, though the extended uptime must be awesome. I'd even consider something similar, were it not that you're using the microusb to charge. If only you could connect it straight to the battery, would be so much more convenient. It'd still work in for instance car kits and attached to a pc.
Never the less, well done.
Click to expand...
Click to collapse
You can't plug in directly to the battery since the battery doesn't have a balancer board on it and it would explode if it were to be overcharged without one.
JJbdoggg said:
Looks great, i would try this myself but i cant stand the bulk of extended batteries and the stock metal back would almost defiantly interfere with the current. Where did you get the decal from?
Click to expand...
Click to collapse
I got the decal in the automotive section of Walmart. It came with 2 big/4small stickers for 7usd
UPDATE: Made the microusb head smaller! Letting liquid electrical tape dry then I'll post pics.
this is a really nice mod. what about the possiblly of going via the nav panel connectors instead of micro usb. this would as far as i know leave the usb port free and also not have the disadvantage of having a usb connector attached which can be easily damged.
Personalyu i wouldnt do this mod as i use my phone to tether a hell of a lot so it seems pointless to me, but being able to just sit your phone down and have it charge is awesome.
Great work!!!!
veda_sticks said:
this is a really nice mod. what about the possiblly of going via the nav panel connectors instead of micro usb. this would as far as i know leave the usb port free and also not have the disadvantage of having a usb connector attached which can be easily damged.
Personalyu i wouldnt do this mod as i use my phone to tether a hell of a lot so it seems pointless to me, but being able to just sit your phone down and have it charge is awesome.
Great work!!!!
Click to expand...
Click to collapse
I tired the navpanel connections with no success. If anyone has a multimeter please try to do it to theirs (with charger plugged in).
that is really odd....only think i can think of is manye theres something that needs to happen with the middle pin.
nice work i think that decal are very cute indeed!
PPL this is knowed from a long time! This pins are used for example with Car Kit like CU s400: http://www.slashgear.com/htc-hd2-cu-s400-car-kit-gets-priced-detailed-coming-december-1360143/
This car kit is in two versions: like this on 1st photo - use other battery cover which use this "mysterious" pins to run NaviPanel and charging battery and 2nd version with charging via microUSB port.
I hope this helps a bit.
veda_sticks said:
that is really odd....only think i can think of is manye theres something that needs to happen with the middle pin.
Click to expand...
Click to collapse
This "odd" middle pin you can find in every phone battery too. If you depart any battery you can find there a little electronic circuit.
I think, that this pin is used to metering battery charge, but i can be wrong - im not advanced in electornics.
I'm well aware of the existance of these products but cannot figure out what the three contacts below the batteries are.
Maybe some users having one. In that case he/she can make photos of all connectors or better - check it with multimeter which connector is +, - and this middle one.
Maybe some service manuals can tell something more abt this. I searched for it and i did'nt find nothing useful.
FRANQ_23_PL said:
Maybe some users having one. In that case he/she can make photos of all connectors or better - check it with multimeter which connector is +, - and this middle one.
Maybe some service manuals can tell something more abt this. I searched for it and i did'nt find nothing useful.
Click to expand...
Click to collapse
I also did a search on google and xda but with no luck. I don't think it inputs 5v into the machine since I did shoot 5v into the 3 connectors using different combination.
Hi all,
The contact closest to the center of the phone (looking along the longest axis of the phone) is the +5V, the one furthest from the +5V is the ground, and there's a small voltage on the center contact, positive to ground. These +5V voltage shows up (on my phone) only when the mini-USB charger is plugged in.
I've got the +5V terminal of the Pre plate attached to the +5V contact on the phone, and the other one attached to the GND contact. Inductive charging works at 341ma (as measure by the hardware and read by BattClock) at maximum, which is probably not coincidentally also the limit set on USB charging, at least from my laptop.
I tried hooking the Touchstone up to a Apple ~1" cubed charger, didn't get any charge. I haven't read the USB power specifications, but according to the people at the Palm forums you have to have a USB spec power-capable charger to initialize the Touchstone, and the USB ICs signal this by connecting the two data lines. This can be approximated by clipping a USB cable and twisting the data lines together on the Touchstone side of the cable. This allowed the Apple charger to power the Touchstone.
The HTC stock charger works fine, as does an 800ma Verizon charger I had laying around. I tried hooking the Touchstone up to both a [email protected] switching charger and a 5V 8A supply, the Touchstone still charged at 341ma. I'm guessing this is software, firmware or hardware limited, just like the computer USB connection. I would speculate that if you shorted the middle pin to the ground pin, it might remove this restriction. Or fry your phone, I didn't try it.
There's a guy on the Pre forums who got the Touchstone to consume about 1.02A (http://forums.precentral.net/palm-p...b-adapters-touchstone-dock-2.html#post2020491) so the thing can, apparently transfer some power. I don't know how long it would last at those wattages, but I'm going to read a bit on the USB power spec and see if the 341ma limit can be lifted.
It's kind of nice to use the internal connector, because it leaves the microUSB port open. If anyone has any questions feel free to ask. With the relevant portion of the Pre cover stuck to the back of my phone, there are no wires out of the chassis and the added part doesn't add any considerable bulk to the phone. It protrudes less than the camera.
Anyways, hope this isn't a thread-jack or too long, but I figured it might help anyone that's going to take the time to do this.
Thanks to the community here.
Did you dremel and hotglue the plastic case to the metal case? Interweb highfive from me to you!
Can you post pictures of the inside wiring please?
I did. I basically cut out a square from the HD2 back large enough to hold the coiled length of wire that is needed to allow the back to be removed and articulated. Then I used Super Glue to fix the section of the Pre back containing the inductive coil and circuitry to the HD2 back.
If you're trying to maintain your warranty I might suggest DigiKey part number 478-4687-1-ND, it's from the AVX "MOBO Spring Contact Interconnect Solutions" catalog under battery connectors (I can send you a .pdf copy of the catalog, it's too big to upload to forum). This is a 3mm pitch connector that should mate well with the internal connector - but - I don't have calipers so I would measure before ordering. I just soldered the wires to my HD2.
I'll post some pictures soonish.
And yeah, high five for sure. Thanks for pioneering this. My last phone was retired when the power connector became flaky, so it's nice not to have to worry about the contact wearing out.
Ur mod is on a dutch popular website!
http://tweakers.net/nieuws/69360/mod-maakt-draadloos-laden-mogelijk-op-htc-hd2.html
Right angle micro-usb
I'm looking to do the same thing with my Vibrant and have been searching for a similar connector. I just did a quick google search and found these angled connectors:
http://www.usbfirewire.com/u_microb_cables_angled.html
I tried soldering it your way with no sucess
Soldering pins are as shown
(If viewing vertically with top up)
(leftside of hd2) negative x positive (center of hd2)
bumping an old thread to see if you've taken pictures of the contact points yet.
Sorry it took me so long to reply. Two pictures, the first is the terminal with the wires soldered in, the second shows how I got the cables from the Palm coil/board through the cover. The terminals as you look along the longest axis of the phone with the microUSB plug closest to you are GND, something, and +5v.
So from left to right: 1 GND / 2 ? / 3 +5v.
My usb port is faulty. It wiggles a bit and wont allow the phone to charge unless i hold the usb cable in an exact certain position. What is worse it cannot connect to PC as zune wont recognise it. I tried various cables and various PCs. Same problem.
HTC say the usb port is not covered in the warranty and want to charge me between £60 - £100 to repair it.
i am hoping there is a quick diy fix.
Anyone please?
For the charging issue, you could just buy a battery charger. That obviously won't help when it comes to updating your phone though.
If you, or someone you know, has soldering skills, you can get a new USB connector for $4 Canadian off eBay. Even if you have to bring it to a shop to get it done, I'm sure it'll be a lot cheaper than what HTC want to charge you.
Thanks. Already bought the battery charger. Will look into the usb self repair. Any videos on taking HD2 apart?
I bought a Nexus One with the infamous broken power button issue, and I am curious what would the effect be if I short the VCC and GND line in the charging port? Has anyone tried that? I am thinking that it will either fry the board or trick the phone to think that it is charging.
The reason I want to do this is because I travel a lot and I might not have access to USB charging if I want to swap the SIM card. I am familiar with the other tricks regarding remapping the trackball_center and I am going to install a version of CWM that doesn't support charging (that way the phone boots when I plug a charging cable).
So long story short... what do you think about attempting to short the micro USB charging/data port?
dcalpha said:
what do you think about attempting to short the micro USB charging/data port?
Click to expand...
Click to collapse
Not much.
Unless the unit is in USB host mode there will be no voltage on the Vcc line.
Even in USB host mode it should be current limited and do no damage.
Still, I wouldn't do it.
I don't know why you think that shorting it will do something useful.
Renate NST said:
Not much.
Unless the unit is in USB host mode there will be no voltage on the Vcc line.
Even in USB host mode it should be current limited and do no damage.
Still, I wouldn't do it.
I don't know why you think that shorting it will do something useful.
Click to expand...
Click to collapse
I actually do not know, thus I asked... just trying to think outside the box about a way to trick the phone to think it is charging short of carrying a portable battery charger with me (which can be problematic on carry-on luggage).
Another idea I am thinking about is building a small flex cable using a conductive ink pen that permanently connect to the phone's battery on one side and a cut down male micro-usb on the other side (to slim it down). Such cable would be small enough to fold under the battery cover and allow it to close.
My question is: Will the ~3.7v be enough to get the phone to start charging? and do you foresee any issues with feeding power from the battery right back into the phone's charge port?
dcalpha said:
Another idea I am thinking about is building a small flex cable using a conductive ink pen that permanently connect to the phone's battery on one side and a cut down male micro-usb on the other side (to slim it down). Such cable would be small enough to fold under the battery cover and allow it to close.
My question is: Will the ~3.7v be enough to get the phone to start charging? and do you foresee any issues with feeding power from the battery right back into the phone's charge port?
Click to expand...
Click to collapse
I think 3.7 won't be enough. Coz usb giving ~5V. So phone won't charge at smaller voltage.
I'm pretty sure I know the answer to this already, but I'm going to ask anyway. When my Nexus is plugged into my computer, the USB is extremely touchy. The slightest poke makes the computer think it was unplugged and just as quickly plugged back in. But! It quick charges and otherwise charges normally on any cable I plug into it, it's just when I have it plugged into the computer that it has issues. And yes, I've used/tried different cables. They all act more or less the same.
I'm 90% sure this means the USB port is on its way out, but I wanted to bounce this off other people before I just went and replaced the port. I know it's a major pain and finding compatible parts is as well. On that note, if someone knows of a reputable place to buy replacement parts for this thing, kindly let me know. Thanks!
Try to find out if there is dust or something in the usb port.
I had it too but with normal charging that the cable would go in not easy, and touching it stopped the charging.
Had to get out the dust and filth with a thin needle. After that all worked ok.
Cable went in smooth again too.