Related
edit: Kindle Fire fastboot working. Allows for reflashing ROMs and booting over USB.
Recommended that you have your kindle already opened so that you can get to the battery cable to hard reset if necessary.
Instructions to follow.
transfuntioner said:
<posting here as i dont have access to devel forum yet>
Looking at the bootloader & the u-boot source, it looks like there's 2 ways to get to fastboot. The bootmode nvram setting, and a special usb cable.. I think I'll go the nvram route though I havent investigated how to set it yet.
Just to be prepared I'm going to add usb driver's inf.
%SingleBootLoaderInterface% = USB_Install, USB\VID_1949&PID_0FFF
So .. anyone else working on this?
Click to expand...
Click to collapse
I dont have a gingerbread build handy, is there another dev that can build me a fastboot.exe to include 0x1949?
I think my fire is stuck in fastboot mode.
transfuntioner said:
I dont have a gingerbread build handy, is there another dev that can build me a fastboot.exe to include 0x1949?
I think my fire is stuck in fastboot mode.
Click to expand...
Click to collapse
NVM on the fastboot.exe request, I have a working one.
fastboot mode is confirmed .. i have a fastboot talking to the fire. It shows up in 'fastboot devices' (the id is 0123456789abcdef), and responds to reboot & boot commands.
Now trying to boot out of fb mode, I should have set the 'other' nvram bootmode
NOTE: Instructions are terse and intended towards developers for now.
Standard disclaimer, I am not liable if you brick your fire.
Requisities:
- working adb, (on windows) with the additional %SingleBootLoaderInterface% entry mentioned
- working fastboot binary that recognizes / allows specifying the vendor id (0x1949)
- root. it may work without, but you probably want or have it already
Also recommended:
- boot.img from the latest sw update.
Procedure:
- get a adb shell
- use the '/system/bin/idme' command to set the bootmode. I suggest you first run 'idme ?' and write down your default, mine is "4000 0".
- if you set bootmode to 0x4002, the fire will stay in fastboot mode when it reboots
- if you set bootmode to 0x4003, it's supposed to timeout from fastboot mode, but I did not have much luck getting a normal boot after the timeout (did not play too much here).
- if you decide you dont want fastboot mode, run 'idme bootmode "4000 0"' to reset back to default for normal booting.
WARNING:
IF YOU REBOOT AT THIS POINT THE FIRE WILL BE IN THE FASTBOOT MODE. I HAVE NOT FOUND A WAY TO EXIT THIS MODE AND RETURN TO THE NORMAL OS WITHOUT A WORKING FASTBOOT CLIENT.
REPEAT:
YOU MAY BE BRICKED IF YOU DONT HAVE WORKING TOOLS.
When you boot into fastboot mode, it will show the "Kindle Fire" logo. The power button does not appear to do anything; therefore, if you boot a bad kernel/image it may get stuck and require a hard reset (pulling the battery cable).
You should now have access to the standard flashboot functionality (update, flash, usb boot, etc). Note that reboot-bootloader will bring you back to fastboot.
I currently use 'fastboot boot boot.img' (from the sw update) to get back to a working state. Once booted, use idme to disable fastboot.
Now, on to recovery's & custom roms!
so any more information on the "special usb cable" like what size resistor on pin 4?
death2all110 said:
so any more information on the "special usb cable" like what size resistor on pin 4?
Click to expand...
Click to collapse
I dont have hardware handy to determine this, but having a cable will definitely make things easier going forward.
Brief updates..
Unlike previously mentioned, it looks like long press power button typically should work.
The idme command is available in the bootloader. So you can set normal bootup mode from fastboot, then reboot. eg.
fastboot oem idme bootmode 4000
fastboot reboot
How to get latest update pack ?
Sent from my SAMSUNG-SGH-I777 using XDA Premium App
any idea what tools i can use to check what amount of resistance i need? I may just go out to the garage and grab 3 100k resistors and try the numerous SGS2 methods (specifically 3 resistors twisted together and jumping pins 4 & 5
Stuck in fastboot
Hello,
I followed these steps including adding the %SingleBootLoaderInterface% line mentions to the usb inf. I was able to get the Kindle Fire to set bootmode to 0x4002.
I downloaded fastboot from here, 32-bit only?
http://forum.xda-developers.com/showthread.php?t=463627
Tried to get fastboot 64-bit via this route, no good:
http://rootzwiki.com/topic/4551-guide-making-fastboot-work-on-64-bit-windows-7-systems/
Now that it's in bootmode, neither my x64 PC or x86 Mac can see the device via a recent fastboot.exe and fastboot-mac application using a standard mini-USB cable. Suggestions? Is there a different fastboot.exe that I should be using?
transfuntioner said:
NOTE: Instructions are terse and intended towards developers for now.
Standard disclaimer, I am not liable if you brick your fire.
Requisities:
- working adb, (on windows) with the additional %SingleBootLoaderInterface% entry mentioned
- working fastboot binary that recognizes / allows specifying the vendor id (0x1949)
- root. it may work without, but you probably want or have it already
Also recommended:
- boot.img from the latest sw update.
Procedure:
- get a adb shell
- use the '/system/bin/idme' command to set the bootmode. I suggest you first run 'idme ?' and write down your default, mine is "4000 0".
- if you set bootmode to 0x4002, the fire will stay in fastboot mode when it reboots
- if you set bootmode to 0x4003, it's supposed to timeout from fastboot mode, but I did not have much luck getting a normal boot after the timeout (did not play too much here).
- if you decide you dont want fastboot mode, run 'idme bootmode "4000 0"' to reset back to default for normal booting.
WARNING:
IF YOU REBOOT AT THIS POINT THE FIRE WILL BE IN THE FASTBOOT MODE. I HAVE NOT FOUND A WAY TO EXIT THIS MODE AND RETURN TO THE NORMAL OS WITHOUT A WORKING FASTBOOT CLIENT.
REPEAT:
YOU MAY BE BRICKED IF YOU DONT HAVE WORKING TOOLS.
When you boot into fastboot mode, it will show the "Kindle Fire" logo. The power button does not appear to do anything; therefore, if you boot a bad kernel/image it may get stuck and require a hard reset (pulling the battery cable).
You should now have access to the standard flashboot functionality (update, flash, usb boot, etc). Note that reboot-bootloader will bring you back to fastboot.
I currently use 'fastboot boot boot.img' (from the sw update) to get back to a working state. Once booted, use idme to disable fastboot.
Now, on to recovery's & custom roms!
Click to expand...
Click to collapse
I had the same issue....but i fixed it!
Code:
fastboot -i 0x1949 oem idme bootmode 0x4000
fastbooot -i 0x1949 reboot
Played with the 0x4003 fastboot "countdown" mode a bit. Seems like it is timing out of fastboot, but not continuing to boot up the rest of the way. After a few seconds the kindle fire logo goes away and the device no longer responds to fastboot commands. Waited maybe a minute or so after it left fastboot and it didn't boot. Though since you found that we can set the bootmode value from fastboot it doesn't really matter.
Also have been playing around with attempting to get my fire to boot a modified boot image. So far I've simply extracted the kernel/initrd from the 6.1 update boot.img and repacked it without modifications. Unfortunately the Fire refused to boot the resulting image.
Going to continue fiddling.
Well managed to successfully repack a boot.img.
The problem i was facing was caused by 2 issues while running mkbootimg.
1) Derped and didn't specify the correct page size (4096)
2) Needed to include a base address of 0x80000000.
wait i'm stuck in the phase where it times out after the kindle logo and it doesn't respond to fastboot commands... what did you do to get out of that?
any help would be GREATLY appreciated before my battery dies. i have my clockwork port saved on the sdcard!
or if somebody can upload their fastboot binary
edit: got it, i needed to specify the vendor id as mentioned on the bottom of page one
thanks to those who were trying to help me (although probably nobody as it's 3am...)
JackpotClavin said:
wait i'm stuck in the phase where it times out after the kindle logo and it doesn't respond to fastboot commands... what did you do to get out of that?
any help would be GREATLY appreciated before my battery dies. i have my clockwork port saved on the sdcard!
or if somebody can upload their fastboot binary
Click to expand...
Click to collapse
I did a long press of the power button and it turned off. Then before turning it back on i ran:
Code:
fastboot oem idme bootmode 4000
Let it sit in "waiting for device" and powered the kindle back on.
Attached my fastboot binary for linux if it's useful for you. It's compiled from AOSP with the 0x1949 vendorid added in.
I don't have the -i option on my version of fastboot. Could you post a windows version of the one you're using?
Edit: found version of fastboot.exe that supports -i in SDK_r07.
I can't post outside links yet, but here's the URL:
code.google.com/p/softy-warely/downloads/detail?name=android-sdk_r07-windows.zip&can=2&q=
Thanks death2all110. Got it to reboot to break out of the fastboot cycle.
New question:
I did fastboot -i 0x1949 boot recovery.img (from the Kindle 6.1 update) and now I can't fastboot back in to break out of the fastboot cycle again:
C:\Program Files (x86)\Android\android-sdk\platform-tools>fastboot -i 0x1949 oem idme bootmode 4000
< waiting for device >
I'm giving CM7 a shot right now. Gonna fastboot flash the system.img generated as well as the boot.img although I doubt this will work
death2all110 said:
any idea what tools i can use to check what amount of resistance i need? I may just go out to the garage and grab 3 100k resistors and try the numerous SGS2 methods (specifically 3 resistors twisted together and jumping pins 4 & 5
Click to expand...
Click to collapse
I dont think it'll hurt to try.. FWIW I didnt see anythign obvious in the source or from quick googling for the specs. Didnt spend a lot of effort on it though.
JackpotClavin said:
I'm giving CM7 a shot right now. Gonna fastboot flash the system.img generated as well as the boot.img although I doubt this will work
Click to expand...
Click to collapse
Yeah I am going to play with existing gingerbread builds as well because I dont think ICS will ever finish building on my machine!
I am planning on just flashing system.img and then usb boot with the stock kindle kernel / boot.img.
It didnt do anything, I found a Micro USB for LG Devices with selectable resistance. But I might buy an actual USB jig for the SGS2 but i dont want to waste my money on it if it doesn't work...
Hmm. Theres gotta be a way...
careful flashing
This may be known to experienced android devs but I thought I'd mention as I am not & just ran into it.
When you flash an individual partition you're limited by the ram, in this case the image size needs to be less than the value reported.
fastboot getvar downloadsize
downloadsize: 1d0000000
So around 486 megs.. just some extras steps needed if you're working with the 512M system partition.
So, I've been up all night after buying this Fire trying to fix it, and I've decided to go along with my original decision to just return it. I'll rewind a bit to give you guys a play by play to show how I got to what I've determined is a FUBAR situation, and hopefully you guys can help me at least remove TWRP so I can return it without much issue.
If it's tl;dr, I bolded the main errors I got from the console and TWRP
1. I purchased my Kindle Fire from Best Buy with a 1 Year Protection plan, so in all reality, I could just break it in half and get a replacement, but I don't necessarily want a replacement.
2. I initially purchased it for my mom, but when I found out that the stock Fire OS didn't have Korean input or the option to have a Korean interface, I did a bit of research and started reading up on how to root, how to install the market, things like that. My mom's not a native English speaker, so this was an important thing for her, etc etc.
3. I read multiple guides on this forum and others, and rooted using the guide found here , since a few of the threads I was reading through seemed to point in that direction, and I had a bad experience with SOCR on my Droid X.
4. The root was successful, so I moved on and used KFU .3 to do the rest of the important bits; android market, etc etc.
5. Everything was working fine, but, after looking through it, I realized that it wouldn't work for what I needed it to, and I would have to return it, so, I attempted to unroot the tablet using TWRP's interface.
6. I cleared the cache, the devlak cache, and system wiped, then restored using the system restore point in the TWRP folder, figuring after that, the Kindle would boot up with stock OS and then I would just system restore the default way. This method got me stuck in a recovery-loop, and no matter what I did, the Fire always booted to recovery mode.
7. I figured I had bricked it, so I followed the steps in this guide, but always seemed to have problems at the step where I have to chmod 755 of the zergRush. I get "Not a directory" error, which after doing some research, I believe is on account of me no longer having rw privilege?
8. I looked around some more, ignoring that guide, and found a method to force-push the amazon update, but TWRP would no longer run the update, saying it could not Mount the SD Card due to an Invalid Argument, and I have yet to determine what that means.
9. After manually changing it to fastboot in an attempt to at least get it out of recovery mode, I have the Fire recognizable as a device in my ADB, but it is now stuck in a fastboot loop, and when I attempt to re-root it in order to give myself rw privileges again, it stalls on "waiting for device" and never gets past that point.
Update
I tried to reroot while the Fire was stuck in the Kindle Fire splash screen using the KFU tool, and used zergRush, but the error message I got was - exec '/system/bin/sh' failed: No such file or directory (2) - 4 times over.
What I think the problem is, is that when I wiped the cache/devlak cache/ and system reformatted, it wiped my SU privileges, and as a result, no longer allowed me to write the backup to the Fire, therefore leaving me in a perpetual state of limbo?
What I'm asking for from you is;
What can I do to fix this?
Is there any more information you need/want from me?
And finally,
Is there an easy way for me to remove TWRP from the system?
Thank you.
Hi!
There are a lot of great tips regarding TWRP and fastboot over at RootzWiki.
Some users are reporting the same fastboot loop that you currently experience. I suggest you read the thread and follow the suggestions. One suggestion which you may want to try first is the one in this post.
Thank you for the reply. I did as you suggested and followed the links and the post on the guide, and although that did change the nature of my fastboot loop, I'm still stuck in a fastboot loop.
I was initially stuck in a fastboot loop on the Kindle Fire logo, which I determined by running fastboot devices, while it was stuck on that logo, and it showed the device as being fastboot. After following that guide, and using the hard reset, then using the "How to Unbrick" in order to change back to a normal boot, I'm stuck in a fastboot loop on the TWRP splash screen of a triangle with a fire in it. I'll continue looking through the guides to see if I can solve the problem, but thank you once again, and sorry for not clarifying which type of fastboot loop I was in.
Sorry it didn't work out! However...
isjonamon said:
I'm stuck in a fastboot loop on the TWRP splash screen of a triangle with a fire in it.
Click to expand...
Click to collapse
I really though the solution posted over at RootzWizi would solve this problem. Getting stuck at the yellow triangle is 'common'. I really though adding
%SingleAdbInterface% = USB_Install, USB\VID_18D1&PID_0100
%CompositeAdbInterface% = USB_Install, USB\VID_18D1&PID_0100&MI_01
Click to expand...
Click to collapse
to android_winusb.inf would solve it. But if you are able to recognize your Fire in fastboot mode via your PC, I guess that's not where your problem is.
Is this tip to any help?
And lastly... the great Kindle Fire Utility thread is worth checking out, in case you haven't already
I hope you'll find a solution to this problem!
I've tried the tip you linked me to, and sadly it didn't do anything for me.
Moving on, though, I'm reading through the KFU thread again to see if there was anything I missed, and decided I might as well try re-flashing to CM7 to see if I can at least get it working up to a rooted/rom standpoint. I figure from there, I can at least have a working platform to factory reset from. If I can't do that... well...
Does anyone know a way to just return everything to factory settings? To just wipe everything and make it so it turns on like it's out of the box? Either through adb commands, or TWRP or anything?
Sorry for the double post, but I managed to get CM7 back up on my Fire, and managed to regain SU access. Can anyone point me to a guide to restoring it back to its former "glory" so I can return it?
Fixed it!!
For anyone interested, this is what worked for me;
From where I ended up with the problem, I followed hachiueno's advice and read through the KFU's thread as well as the TWRP thread on Rootzwiki, that led me to adding those lines to the device firmware, which I think was the first step in the solution, so...
Step 1. Add
%SingleAdbInterface% = USB_Install, USB\VID_18D1&PID_0100
%CompositeAdbInterface% = USB_Install, USB\VID_18D1&PID_0100&MI_01
to android_winusb.inf , then restart your computer with your Fire unplugged.
After that, I was inspired, through reading the KFU thread, to attempt to manually install CM7 since I wasn't having much luck zergRushing on my own, so, I went to the CM7 thread and pushed the Update.zip there, and used my TWRP to install that, effectively rebuilding my filestructure, since it seems the Kindle Fire doesn't have so much as a SH folder in it.
Step 2. MANUALLY (maybe) install CM7 if you can.
Once I got CM7 up and working, using the USB mounting option, I replaced the update.zip in the sdcard folder with the Amazon 6.2 firmware downloaded from their website, renamed to update.zip, and then unmounted my fire from my laptop.
Step 3. Download the Amazon 6.2 Firmware from amazon's website (I can't post...), rename it to update.zip, and replace the CM7 mod update.zip in your /sdcard directory with it.
Then, I figured if I ran TWRP like it was supposed to run, and just ran the update.zip like any other ROM, it should fill in the blanks in the filesstructure, bypassing Amazon's own lack of certain folders, and various other things, filling in the gaps as they were. The next step might be entirely redundant, since I'm a bit clueless, and it might have been entirely luck on my part, but I initially forgot to wipe my cache, devlak cache, and system restore, so I did all that and did it again, and my wishful thinking leads me to believe that doing that saved my ass from having a crapton of errors....
Step 4. Using the install function on TWRP, install the renamed Amazon update.zip, reboot, clear your cache, devlak cache, system reformat, then reinstall the update.zip. Reboot one more time, and you should come up to the Kindle Fire splash screen. Leave it for a few minutes, and it'll be like it just came out of the box.
Thanks for all your help. I love you. Seriously. No homo. Maybe a little. I love you.
Good to hear that you managed to boot it again!
isjonamon said:
Sorry for the double post, but I managed to get CM7 back up on my Fire, and managed to regain SU access. Can anyone point me to a guide to restoring it back to its former "glory" so I can return it?
Click to expand...
Click to collapse
This guide seems to be an easy solution to this. However, no one has replied any success or failure, so not sure if it's 100% bulletproof for everyone... if I were you, I would follow JackpotClavin's guide here. He's a known developer here and knows what he's doing, and many successful replies from users having used this method... so yeah, just to be 'sure' (can you ever be...?) that you won't experience any further problems, I recommend the last one.
I actually used the first guide in order to get the Amazon update, but couldn't post a reply since I'm still a noob. I had to do a few things differently, and ultimately got a few different results, but posted up my own version of the steps.
Once again, thanks for all your help!
It seems to me that the majority of problems people are having are driver related. When I was using KFU to install TWRP it stalled half way through and just said waiting for device. Just had to install drivers again and it happily completed the install.
Sent from my Kindle Fire using xda premium
all u needed do initially was change bootmode it seemed. thrn u went and did all kinds of stuff that wasnt necessary.
sent from my kindle fire
smirkis said:
all u needed do initially was change bootmode it seemed. thrn u went and did all kinds of stuff that wasnt necessary.
sent from my kindle fire
Click to expand...
Click to collapse
I actually changed bootmodes quite frequently, following multiple threads and guides, changing from recovery, to normal, to fastboot, and back and forth when called for. Changing to fastboot stuck me in an eternal fastboot loop, changing to normal reverted me to a recovery loop, and recovery was the only bootmode I could access adb from.
Sheolrock said:
It seems to me that the majority of problems people are having are driver related. When I was using KFU to install TWRP it stalled half way through and just said waiting for device. Just had to install drivers again and it happily completed the install.
Sent from my Kindle Fire using xda premium
Click to expand...
Click to collapse
Driver issues seemed to be part of the problem for me, but just updating the drivers didn't fix the issue entirely. I'm jealous that you got it to work with just a driver update...
Hey i believe im in the same problem but i keep reading the posts and im still stuck and i have no idea what to do im worried that i cant fix it.... Some please help me ASAP
Thanks in advance
wrong boot mode ?
with adb:
adb shell su -c "idme bootmode 4000"
adb reboot
with fastboot:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot reboot
bad drivers ?
http://forum.xda-developers.com/showpost.php?p=20855280&postcount=54
I have had the looping problem and none of these would fix it. I got it to work by adding those lines to android_winusb and running the run.bat, trying to make it switch to normal mode as the kindle was turning on. Somewhere along the yellow triangle when it was loading it accepted the command from KFU. Hope this helps, only thing that worked for me.
the drivers i included contain all the necessary entries in adb_usb.ini and android_winusb.inf
Please can someone help me!?
I did idme bootmode 4002 and now my fire won't boot up or show up in android adb. Any solution?
awidawad said:
I did idme bootmode 4002 and now my fire won't boot up or show up in android adb. Any solution?
Click to expand...
Click to collapse
you switched it to fastboot (4002) - adb commands are not working in fastboot mode !
little guide:
driver (under android phone):
normal & recovery boot: -> android composite adb interface
fastboot: -> android adb interface
here all the possible commands to change bootmode:
with adb (secure kernel):
adb shell su -c "idme bootmode 4000"
adb reboot
or (twrp or unsecure kernel):
adb shell idme bootmode 4000
adb reboot
with fastboot:
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
or:
fastboot -i 0x18d1 oem idme bootmode 4000
fastboot -i 0x18d1 reboot
or:
fastboot oem idme bootmode 4000
fastboot reboot
the number is the bootmode you want to switch to:
normal boot -> 4000
fastboot -> 4002
boot to recovery -> 5001
and if you know:
normal boot -> adb commands YES -> fastboot commands NO
fastboot -> adb commands NO -> fastboot commands YES
recovery -> adb commands YES -> fastboot commands NO
then you only have to count 1 and 1 together and can master nearly each hanging situation !
Click to expand...
Click to collapse
Not sure if this is totally helpful to anyone but originally I thought the thread was started with a posting of being stuck bootlooping into twrp in recovery mode with a complete loss of file structure. I had this same issue my Kindle would not start in anything but straight to twrp and if I tried to flash my CM9 ICS rom it was not there and only the twrp folder empty was. So I went to mount and mounted usb storage and moved the stock update zip file from amazon to the twrp folder and flashed that. Worked like a charm now I appear to be straight stock. I am no developer of this stuff I just am a bit of a tinkerer so don't understand all the code stuff but it starts like a normal kindle and appears totally stock. So hopefuly that helps you return your deice to stock for return or to continue wahtever modifications you intend.
2992
UPDATE 3: I've got it back to as stock as I can get it. I think I'm going to just return it and get a new one. Thank you all for your help.
UPDATE 2: As of right now, I'd like to completely remove FFF from the device, but I can only use fastboot to do it. I have absolutely no adb access. Is there a way?
UPDATE: Here is a video showing what is happening to my KF: http://www.youtube.com/watch?v=MH6oUg1NmC0
I hate to start another thread about boot loops/bricking, but I'm not sure what's going on with my fire.
I had CM7 installed successfully since the day after Christmas. This morning I woke up and my Fire was being really sluggish, so I rebooted it (I did not select reboot into recovery).
After it powered on, I was stuck at the CM7 boot screen (with the skateboarding android). I let it sit, but no luck. I went into TWRP to try and restore the backup I made of the stock rom. It looked successful, but when I rebooted I was stuck at the Kindle Fire boot screen.
Next, I tried wiping the device and re-installing CM7, but I received an error (something along the lines of E:Error unable to find /tmp/sideload/blahblah).
So I again restored my backup of the stock rom. Now when I power on my Fire I see the yellow triangle, then the kindle fire logo, yellow triangle, kindle fire logo, and it just keeps repeating. The problem is I am unable to connect to adb because the PC only seems to recognize the adb device for a few seconds after the yellow triangle, which does not give me enough time to fix the problem.
Any ideas?
looks like you'r out of battery ! the kf is rebooting !
would take the wall charger and charge for an hour
it's not possible to charge with the computer - it lasts forever
then it should respond in a stable state
b63 said:
looks like you'r out of battery ! the kf is rebooting !
would take the wall charger and charge for an hour
it's not possible to charge with the computer - it lasts forever
then it should respond in a stable state
Click to expand...
Click to collapse
Recovery shows my battery level to be at 53%. I've got it on the charger now, but I have a feeling there is something else going on.
Also, I am unable to mount my Fire's SD to my computer in recovery. It looks like it is working, but my computer never acknowledges it.
maybe because your last installation failed
nevertheless i would try to charge and then go in twrp and retry the installation
if that's not sucessful i would try to switch the kf to fastboot and copy a new rom. stock or prerooted stock or cm7 - whatever you like
in twrp there is a point "mount" - sdcard - then you should get it from computer
b63 said:
maybe because your last installation failed
nevertheless i would try to charge and then go in twrp and retry the installation
if that's not sucessful i would try to switch the kf to fastboot and copy a new rom. stock or prerooted stock or cm7 - whatever you like
in twrp there is a point "mount" - sdcard - then you should get it from computer
Click to expand...
Click to collapse
Thanks for the reply. Is adb required to get into fastboot? The problem is that I am unable to get into adb because my computer only sees the Fire for about 1 second. When I go into device manager, I don't see it at all.
EDIT: Yeah, I see the mount in TWRP, but it does not do anything when I select it.
Hi Im a beginner but Id like to try to help :
In case you become desperate ignore twrp's battery display and try wall charger.
Anorher idea id have is to shut down throughr twrp and start up then instead of rebooting.
ADB is needed to get into fastboot, but it's quick. If you use KFU, you can probably hit the option during the couple seconds you have available. I would say your best bet, however, is booting into twrp, doing a full wipe of system, cache, davlik cache, and maybe data, and then trying the rom install again.
skourg3 said:
ADB is needed to get into fastboot, but it's quick. If you use KFU, you can probably hit the option during the couple seconds you have available. I would say your best bet, however, is booting into twrp, doing a full wipe of system, cache, davlik cache, and maybe data, and then trying the rom install again.
Click to expand...
Click to collapse
So this time it looks like the installation worked in TWRP, but after reboot now I'm stuck at the CM7 boot screen. This is at least some progress, so when I get home I'll see what I can do.
Sent via my internet connected mobile cellular telephone.
Well, the battery is definitely not the issue. I've been trying to get fastboot, but the problem is the fact that I can not get adb. Has anyone else had issues with getting adb? I've already tried to install the drivers, and that doesn't work.
EDIT: I've tried issuing "adb devices" from the command prompt repeatedly as soon as I hear the ding until it disconnects a second later, but still I have had no luck.
Also, I found this thread in which someone else appears to have had a similar issue to mine.
[Q] New kind of unfixable Super Brick?
at the moment adb is useless - you should try to get the device in fastboot mode - correctly recognised from your computer - then work with fastboot commands - if you don't get that then your next opinion is buying or making a factory cable - but we should try to avoid that ...
b63 said:
at the moment adb is useless - you should try to get the device in fastboot mode - correctly recognised from your computer - then work with fastboot commands - if you don't get that then your next opinion is buying or making a factory cable - but we should try to avoid that ...
Click to expand...
Click to collapse
I can not seem to get fastboot to work either. Does fastboot rely on adb? Or do you just run the .exe file? I tried to run it, and nothing happened.
fastboot has nothing to do with adb - calling just the exe does nothing -
you have to issue fastboot commands
ok have reread the whole thread and have some ideas:
your currently stuck at the cm7 boot screen ?
have you used the "stock rom version" to wipe data and cache partitions as described here ?
http://forum.xda-developers.com/showthread.php?t=1390773
perhaps it will help to wipe data/cache with twrp ...
b63 said:
fastboot has nothing to do with adb - calling just the exe does nothing -
you have to issue fastboot commands
ok have reread the whole thread and have some ideas:
your currently stuck at the cm7 boot screen ?
have you used the "stock rom version" to wipe data and cache partitions as described here ?
http://forum.xda-developers.com/showthread.php?t=1390773
perhaps it will help to wipe data/cache with twrp ...
Click to expand...
Click to collapse
Just wanted to let you know I updated the OP with a video showing what is happening to my KF.
Haven't tried that particular rom yet, but I have wiped data and cache and attempted to re-install CM7.
great idea with the video !!!
b63 said:
fastboot has nothing to do with adb - calling just the exe does nothing -
you have to issue fastboot commands
ok have reread the whole thread and have some ideas:
your currently stuck at the cm7 boot screen ?
have you used the "stock rom version" to wipe data and cache partitions as described here ?
http://forum.xda-developers.com/showthread.php?t=1390773
perhaps it will help to wipe data/cache with twrp ...
Click to expand...
Click to collapse
OK, so I restored my original rooted kindle rom, but I still can't get into fastboot because of the problem I showed in the video. It is doing exactly the same thing, just instead of the CM7 boot screen, it is the Kindle Fire boot screen.
Is is possible to get into fastboot without the computer? Can anyone think of a reason why I would not be able to mount my device in TWRP?
I just want to understand something about fastboot... can you upload and flash roms with it? Or can you only get TWRP / FFF with it? I ask because I already have them, and I still can't do anything (mount from inside TWRP doesn't work). Thanks!
Sent via my internet connected mobile cellular telephone.
with fastboot you can install the newest fff and if you need twrp
but with the newest fff you can issue ""fastboot oem format"
see here:
http://forum.xda-developers.com/showthread.php?t=1369405
that should solve every issue ...
b63 said:
with fastboot you can install the newest fff and if you need twrp
but with the newest fff you can issue ""fastboot oem format"
see here:
http://forum.xda-developers.com/showthread.php?t=1369405
that should solve every issue ...
Click to expand...
Click to collapse
Cool. I just ordered one of SkOrPn's cables, so once I get it I'll be sure to give an update. Thanks for all the help so far!
The cable isn't need when you have the FFF bootloader, in fact, when your computer does see the device for the short amount of time shown in the video, fastboot is active. It's a feature of FFF. Fastboot is a command line tool like adb but is used for different things. It comes in Android sdk which if you have that, you should update the tools packages in the Android manager and it will update adb and fastboot. It looks like something is not working correctly in twrp and the OS is failing to load. I'm not sure you need to oem format tho.....
At some point you had to have used fastboot to install twrp and/or FFF.... Unless you used adb dd? :what:
Anyway, I can help more but it's late where I am, need to sleep. Was going to write more but... Need sleep lol. I'll post some questions and check back tomorrow.
Have you used adb before? Do you know if platform-tools is in your environment variables PATH? In other words, can you open up cmd and type adb or do you need to "cd" to platform-tools then use adb? If you know where adb is located? If so, is a file called fastboot in there? (Maby called fastboot.exe)
foxdog66 said:
The cable isn't need when you have the FFF bootloader, in fact, when your computer does see the device for the short amount of time shown in the video, fastboot is active. It's a feature of FFF. Fastboot is a command line tool like adb but is used for different things. It comes in Android sdk which if you have that, you should update the tools packages in the Android manager and it will update adb and fastboot. It looks like something is not working correctly in twrp and the OS is failing to load. I'm not sure you need to oem format tho.....
At some point you had to have used fastboot to install twrp and/or FFF.... Unless you used adb dd? :what:
Anyway, I can help more but it's late where I am, need to sleep. Was going to write more but... Need sleep lol. I'll post some questions and check back tomorrow.
Have you used adb before? Do you know if platform-tools is in your environment variables PATH? In other words, can you open up cmd and type adb or do you need to "cd" to platform-tools then use adb? If you know where adb is located? If so, is a file called fastboot in there? (Maby called fastboot.exe)
Click to expand...
Click to collapse
Yep, I've used adb successfully, and it is set up as an environmental variable. I actually installed FFF and TWRP with the KFU. Problem is I think something else is botched; perhaps it is TWRP itself, since I am unable to mount from TWRP. I'll try again when I get home.
Sent via my internet connected mobile cellular telephone.
Hello all,
I did a very stupid thing, i have wrongfuly followed this instruction
fastboot -i 0x1949 flash bootloader <name of firefirefire image here>
fastboot -i 0x1949 flash recovery <name of recovery image here>
instead of FFF image, i put in FFF.ZIP but successfully put in the openrecovery....img
Now my KF wont open, please help!
Do you think a Factory cable can bring it to life?
================================
SOLVED - KINDLE FIRE ALIVE!!!!
================================
What i Did.
1. Just follow the instructions in FireKit USB discussion
2. I had a hard time opening the KF, managed to break a couple of clips holding the pack panel, and scratch it a bit, but enough hold it back.
3. Tips: connect the USB end to the kindle first, then when you are ready connect the other end to the computer USB port, it is much easier.
vertcam9 said:
Do you think a Factory cable can bring it to life?
Click to expand...
Click to collapse
Unfortunately, no.
But it is fixable
http://forum.xda-developers.com/showthread.php?t=1430038
yes u can do it with firekit live usb i have done
u can try firekit live usb i have done same thing and booted to yellow triangle but now it stucked
when i came out of the deep brick with the usb trick in firekit i had to oem format then i flashed new bootloader & recovery (being very careful, this time ) then
fastboot -i 0x1949 oem idme bootmode 4000
fastboot -i 0x1949 reboot
thanks,
i will try FireKit USB. Just a question.
1. "fk" file contains all already right? the recovery and FFF.
2. I just execute the command to fix FF and twrp ?
3. do i need a separate file for FFF and TWRP?
vertcam9 said:
thanks,
i will try FireKit USB. Just a question.
1. "fk" file contains all already right? the recovery and FFF.
2. I just execute the command to fix FF and twrp ?
3. do i need a separate file for FFF and TWRP?
Click to expand...
Click to collapse
1) Yes
2) You'll probably want to use the usb_install_fff_twrp script. If that doesn't work, try usb_fix_parts_and_install_fff_twrp, which also writes a new partition table and flashes the xloader
3) Older versions of both are included. These are sufficient to try to get your device back to a bootable state. You can upgrade them later.
In case the directions were not clear to you... you will very likely need to open up the back of the case and use the "shorting trick" to enable usbboot mode.
vertcam9 said:
Hello all,
I did a very stupid thing, i have wrongfuly followed this instruction
fastboot -i 0x1949 flash bootloader <name of firefirefire image here>
fastboot -i 0x1949 flash recovery <name of recovery image here>
instead of FFF image, i put in FFF.ZIP but successfully put in the openrecovery....img
Now my KF wont open, please help!
Do you think a Factory cable can bring it to life?
Click to expand...
Click to collapse
I did the exact same thing when working on one of the three KFs in my house (and I have been doing this for a long time). : )
By the time I found out about the fix I had also accidentally shorted out my USB port I believe and there was no bringing it back. At least Amazon was kind to me after I told them what I did and replaced the permanent brick with a new device (for a price of course). Now I look and relook before updating the boot loader. I hope your attempt works out for you.
one more thing,
do i need to keep the shorting connected or just until it give signs of life?
vertcam9 said:
one more thing,
do i need to keep the shorting connected or just until it give signs of life?
Click to expand...
Click to collapse
I'm curious as to what you determined on this point?
Hi all,
my nexus wont start after (failed?!) flashing with factory image. bootloader and recovery mode are accessable. i have no backup so i need to flash a new img, but my tablet wont be recognized by my computer anymore(adb drivers not working?!). i tried to deinstall and reinstall the adb drivers alrdy. Device manager shows nexus 7 as Android Phone with "Android Bootloader interface" i cant install adb drivers while in bootloader. in recovery mode i succeeded installing the adb drivers and the tablet is shown correctly in device manager... i need help dont know what to do :crying: .. any suggestions ?
ADB and fastboot drivers are different.
Pirateghost said:
ADB and fastboot drivers are different.
Click to expand...
Click to collapse
yes .. what are u trying to tell me? dont get it.. i used nexus root toolkit to help me apply those drivers.. but it wont work for bootloader/fastboot mode.. i cant flash my tablet because my device wont be recognized by my pc.. im stuck at the bootloaderscreen/fastbootmode....
http://bit.ly/Zqk7pm
and what do u want me to type in there ? i alrdy used google for the last 7 hours ?
oads said:
and what do u want me to type in there ? i alrdy used google for the last 7 hours ?
Click to expand...
Click to collapse
SMH
i filled it in for you.....
Pirateghost said:
SMH
i filled it in for you.....
Click to expand...
Click to collapse
ok sry wasnt patient enough to see... ya well this all makes sense to someone who knows what hes doing but to a noob like me? i thought i alrdy installed fastboot drivers since i unrooted the device a month ago? do i need to deinstall the driver "Android Phone with "Android Bootloader interface"" in device manager first, before applying the new fastboot drivers? pls help me through this i think i damaged enough alrdy ..
no. ADB and fastboot require separate drivers. just install the drivers required for n7 fastboot. there was a link in that list.
there are tutorials here on xda, as well as youtube videos and tutorials on other sites. take a little initiative and learn the ropes. it will help you out later on.
oads said:
ok sry wasnt patient enough to see... ya well this all makes sense to someone who knows what hes doing but to a noob like me? i thought i alrdy installed fastboot drivers since i unrooted the device a month ago? do i need to deinstall the driver "Android Phone with "Android Bootloader interface"" in device manager first, before applying the new fastboot drivers? pls help me through this i think i damaged enough alrdy ..
Click to expand...
Click to collapse
Just relax and take your time.
If your tablet can go into fastboot mode, it is fine and will get better; the only thing standing between it's current state and being brought back to life is a little learning on your part.
Now you see what the problems are with using a toolkit - because they hide all the gory details from you, when the smallest thing goes wrong you are totally helpless due to a lack of understanding about what things are going on underneath the hood. And as it turns out, what "goes on under the hood" isn't really all that complicated either if you do things the full manual way.
Which is not to say that you can not simply just use the toolkit again; if you previously successfully installed drivers that allowed you to talk to the tablet in all of these modes:
- fastboot
- adb w/ custom recovery booted
- adb with Android booted
then it is not evident that you need to be fooling with drivers.
I suggest you read this thread, from start to finish
[GUIDE] Flashing a Factory Image with fastboot / return to stock
Then, go over to your toolkit thread and read it from start to finish. You will see that there are & have been plenty of people in circumstances nearly identical to yours.
good luck
hey thx for ur replies! im a lil more calm now than i was 30 min !
the big problem i still have is that my tablet will show up as Androidphone/Android Bootloader Interface not as an unknown device or as the Nexus 7 it is when i plug it in.. so i cant install the drivers am i correct? well i tried it a few times .. deinstalled and reinstalled .. the problem persists? anyone familiar with that? when i change into Recovery Modus it will show up as Androidphone/Google Nexus ADB Interface.. so my first steps to get rid of this mess would be ...?
oads said:
hey thx for ur replies! im a lil more calm now than i was 30 min !
the big problem i still have is that my tablet will show up as Androidphone/Android Bootloader Interface not as an unknown device or as the Nexus 7 it is when i plug it in.. so i cant install the drivers am i correct? well i tried it a few times .. deinstalled and reinstalled .. the problem persists? anyone familiar with that? when i change into Recovery Modus it will show up as Androidphone/Google Nexus ADB Interface.. so my first steps to get rid of this mess would be ...?
Click to expand...
Click to collapse
that does not sound like a problem to me at all.
You communicate with the device using the "fastboot" program when it is in bootloader/fastboot mode, and with the "adb" program when it is in custom recovery boot.
What you see in the device manager appears to be completely normal - In different modes it shows up in different places. It's not supposed to show up with the same driver in different modes.
Code:
fastboot devices
will show you whether you are communicating successfully with the device when it is in bootloader/fastboot mode, and
Code:
adb devices
will show you whether you are communicating successfully with the device in recovery mode.
I suppose your toolkit has some stoopid menu or buttons someplace that will allow you to test for exactly the same thing. Now all you need to do is stop posting here and read a little bit.
good luck
bftb0 said:
Now all you need to do is stop posting here and read a little bit.
good luck
Click to expand...
Click to collapse
well i did read quite a lot today :crying: i cant find my device when i type in adb devices, im pretty sure i have the right drivers installed since i followed the instructions step by step.
this guy seems to have the same problem: http://forum.xda-developers.com/showthread.php?t=1808076
could someone tell me if this could be a possible solution :http://stackoverflow.com/questions/...e-over-usb-via-adb-devices-from-windows-7-x64
also would it be possible to just get into the bootloader (since thats the purpose of adb drivers and i can do this) and just proceed with fastboot commands ? if i type in fastboot devices the tablet will show up...
In your first post, you indicated that you couldn't connect to the tablet that was in bootloader mode with adb.
And then you were told - once vaguely and once quite specifically - that *nobody* can communicate with the tablet using adb when the tablet is in bootloader/fastboot mode.
As stated previously, use the "fastboot" program when the tablet is in bootloader mode, and use the "adb" program when the tablet is booted to the custom recovery (or the regular android boot if USB debugging has been enabled).
You can use either one of these modes to effect a rescue so long as they are working correctly - they don't need to both be working. Eventually you would want that to be the case, but for the moment why don't you just stick with what is working for you.
If you get a device ID printed when you execute "fastboot devices" when the tablet is in boot loader/fastboot mode, that is all you need to reinstall a factory ROM, using nothing but fastboot.
thx for pointing me in the right direction! so i started flashing with the fastboot commands... as soon i get to: fastboot flash radio radio-tilapia-1231_0.17.0_1025.img
i receive:
error: cannot load 'radio-tilapia-1231_0.17.0_1025.img': No error
any clues? thx in advance
edit:using 4.2.2 factory rom for nexus 7 3g
oads said:
thx for pointing me in the right direction! so i started flashing with the fastboot commands... as soon i get to: fastboot flash radio radio-tilapia-1231_0.17.0_1025.img
i receive:
error: cannot load 'radio-tilapia-1231_0.17.0_1025.img': No error
any clues? thx in advance
edit:using 4.2.2 factory rom for nexus 7 3g
Click to expand...
Click to collapse
Well, I can't see what instructions you are following, and there is a possibility of sensitivity to an exact sequence. In particular, is a
fastboot reboot-bootloader
performed after the bootloader is flashed, but before the radio is flashed? It might be important that you are performing the radio flash from one bootloader vs. the other. Just a guess. (Along the same lines, do you see something unexpected happening, such as a boot to the recovery after the radio flash command?)
There are some other threads on this I think. (I have a grouper device not tilapia) But I thought that those threads were about problems with radio flashing when a custom recovery (rather than a stock recovery) was on the phone, but that was for applying the OTA package for tilapia rather than flashing directly from fastboot.
-------------------------------------------------------
[Edit] whoops, wait a minute.... "cannot load"
When you run fastboot from the command line, the file names you give are relative to the current directory. Did you move those image files into the same directory that you are executing the "fastboot" command from?
Alternately you can specify the full pathname to wherever you unpacked the files, for instance
fastboot flash radio C:\myfolder\unpacked\googlen7\4.2.2\radio-tilapia-1231_0.17.0_1025.img
hi! basically im following this guide http://forum.xda-developers.com/showthread.php?t=1907796!
GSM/HSPA+ devices (nakasig)
Code:
> fastboot erase boot
> fastboot erase cache
> fastboot erase recovery
> fastboot erase system
> fastboot erase userdata
> fastboot flash bootloader bootloader-tilapia-4.18.img
> fastboot reboot-bootloader
> fastboot flash radio radio-tilapia-1231_0.17.0_1025.img
> fastboot reboot-bootloader
> fastboot -w update image-nakasig-jdq39.zip
its all good till i want to flash the radio. The .img is in the correct folder, just tried it again... could it be broken? should i try a other factory update like 4.2.1?
oads said:
hi! basically im following this guide http://forum.xda-developers.com/showthread.php?t=1907796!
GSM/HSPA+ devices (nakasig)
Code:
> fastboot erase boot
> fastboot erase cache
> fastboot erase recovery
> fastboot erase system
> fastboot erase userdata
> fastboot flash bootloader bootloader-tilapia-4.18.img
> fastboot reboot-bootloader
> fastboot flash radio radio-tilapia-1231_0.17.0_1025.img
> fastboot reboot-bootloader
> fastboot -w update image-nakasig-jdq39.zip
its all good till i want to flash the radio. The .img is in the correct folder, just tried it again... could it be broken? should i try a other factory update like 4.2.1?
Click to expand...
Click to collapse
I would complete the rest of the steps first and see if everything is still working. Your device *should* still work just fine with an old radio firmware. (Boot it up and see what radio firmware the OS reports on the Settings... about device... status page).
I'll pull down the tilapia image and tell you what MD5 I observe for the radio image.
just to verify, you actually have the 3g/4g model? or just the wifi only model. if wifi only, there is no radio
Pirateghost said:
just to verify, you actually have the 3g/4g model? or just the wifi only model. if wifi only, there is no radio
Click to expand...
Click to collapse
yes
SHA1
0798439d363beb145d9223a42ed9edf3de1a30f4 nakasig-jdq39-factory-0798439d.tgz
bb824d449f44d2ad43c5d2a463fe1244d2faf525 nakasig-jdq39/radio-tilapia-1231_0.17.0_1205.img
f406ae9133c56200306d5c7d64d151f21e0be3c4 nakasig-jdq39/image-nakasig-jdq39.zip
MD5
ee8db1ed6ff1c007fe12136d4bc65cd8 nakasig-jdq39-factory-0798439d.tgz
276cb738e5b9e18a088b6a3eef8155ad nakasig-jdq39/radio-tilapia-1231_0.17.0_1205.img
4cfa996b6513a7fa53db7cbfd1134396 nakasig-jdq39/image-nakasig-jdq39.zip
radio image is 16,777,216 bytes long
---------- Post added at 05:43 PM ---------- Previous post was at 05:40 PM ----------
the google - provided instructions (flash-all.sh) have 10 second sleeps after the bootloader resets - are you waiting long enough?
fastboot oem unlock
fastboot erase boot
fastboot erase cache
fastboot erase recovery
fastboot erase system
fastboot erase userdata
fastboot flash bootloader bootloader-tilapia-4.18.img
fastboot reboot-bootloader
sleep 10
fastboot flash radio radio-tilapia-1231_0.17.0_1205.img
fastboot reboot-bootloader
sleep 10
Also - something to check since you are rebooting the bootloader - does the device show up correctly in the Windows device manager? (Sometimes with soft reboots I have found the need to pull the USB cable and plug it back in to the PC).