If you have any issue with your outer touch screen and inner LCD screen, this is the Droid X take apart repair guide that will help you take apart the Droid X fairly easily in a step by step manner giving you a chance to replace faulty parts.
This guide should help you replace the following parts:
Motorola Droid X Touch Screen Digitizer
Motorola Droid X LCD Screen Replacement
Motorola Droid X Replacement Battery
Tools:
Small Phillips Screwdriver
Safe Open Pry Tool
Heat Gun/Hair Dryer
Motorola Droix X Take Apart Repair Guide:
The first step is to power down the phone and slip open the battery door so that the battery of the Droid X can be removed.
Removing the U-cover and the top cover is the first task at hand which can be achieved by unscrewing the two screws to using the Small Phillips Screwdriver as shown in the figure below.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This next step involves locating and removing the four screws (2 on the top and 2 on the bottom) on the front end of the phone. These screws are hidden behind covers which should be removed by inserting the safe open pry tool into one end of the phone twisting it to one side till you hear a click which signals that the plastic latch has been unlocked do this for all three sides of each of the two covers. You should also now be able to remove the U-Cover located on the bottom of the phone using the safe open pry tool.
The next task at hand is to remove the back housing of the Droid X. This can be achieved by inserting the safe open pry tool into one end of the phone and running it along its edges. However be careful because the digitizer cable and the flex cable are hidden under the back cover which can easily be damaged if you apply too much force.
You will now need to remove the motherboard of the Droid X which begins with disconnecting the flex cable and digitizer cable (on the right of the phone) from the motherboard using the safe open pry tool. The flex cable can be pried right off while the digitizer cable will first need to be unhooked and then pulled out.
The motherboard pops right out, but be careful because there is a cable attached to the other end of the board which will need to be unfastened prior to being able to completely remove the motherboard. You can use the safe open pry tool to disconnect that cable as you slightly dangle the motherboard to insert the pry tool through.
In this next step you will have to take apart the digitizer and LCD assembly which are separated by a middle plate. There are around thirteen screws securing the middle plate to the digitizer and LCD which need to be removed using the small Phillips screwdriver prior to prying out the middle plate. Also make sure that there aren't any small clips attached to the plate prior to pulling it out.
Once you separate the LCD and digitizer the Droid X is now completely disassembled.
There you have it, the Droid X is completely disassembled. You can now replace old or faulty parts prior to putting everything back together following this guide in reverse.
Nice write up....
Sent from my HTC_Amaze_4G using xda premium
Thanks. Glad you found it useful.
Great write up, came in helpful as I had to replace my LCD and digitizer, BUT, after I had replaced them, my phone went into bootloader mode, I flash the SBF .602 and it went great, you know 10-12 minute write time. I followed all the steps to a T. Pulled the battery, power button + home button, goto recovery wipe data/factory reset, wipe cache then reboot. when it boots back up I get the red Motorola symbol for 10-15 seconds then goes to the green android guy with the yellow ! mark, double volume buttons and goes back to recovery. Any idea to why this happens???? I SBF'ed 3x's with different disks just to make sure it wasn't a bad disk. Gave up on it and said to heck with it and put the old parts back together and everything worked fine.
Just a heads up with what I have: DroidX, Rooted, sys 4.5.602, Android ver 2.3.3, pretty much stock except for root. I did buy this phone used off EBay, everything works except Vibe and the LED notification light. The LCD and digitizer are from another phone that didnt have a motherboard so I just swapped out mine.
Thanks a bunch if you or anyone has an idea to why I am having this issue from swapping out the motherboard.
flatbedder said:
Great write up, came in helpful as I had to replace my LCD and digitizer, BUT, after I had replaced them, my phone went into bootloader mode, I flash the SBF .602 and it went great, you know 10-12 minute write time. I followed all the steps to a T. Pulled the battery, power button + home button, goto recovery wipe data/factory reset, wipe cache then reboot. when it boots back up I get the red Motorola symbol for 10-15 seconds then goes to the green android guy with the yellow ! mark, double volume buttons and goes back to recovery. Any idea to why this happens???? I SBF'ed 3x's with different disks just to make sure it wasn't a bad disk. Gave up on it and said to heck with it and put the old parts back together and everything worked fine.
Just a heads up with what I have: DroidX, Rooted, sys 4.5.602, Android ver 2.3.3, pretty much stock except for root. I did buy this phone used off EBay, everything works except Vibe and the LED notification light. The LCD and digitizer are from another phone that didnt have a motherboard so I just swapped out mine.
Thanks a bunch if you or anyone has an idea to why I am having this issue from swapping out the motherboard.
Click to expand...
Click to collapse
Make sure that none of the buttons are being pressed down during boot. This can happen if you have not put the housing back on correctly and this can cause the issue you have.
awesome repair guide, thanks for the info.
quick question. ive got a lovely droid x i found in a parking lot....run over. completely. most of the components (emi shields at least) look like theyre dented/pressed in but they could be in alright shape, i dunno. any insight? i could post pictures...
the entire assembly is completely worthless but i can replace all that relatively cheaply. i dont know about the esn or anything else (id rather not repair a phone that techinically belongs to asurion....)
edit: looking for a droid x to swap motherboards with, see if this one is alright. i think the main thing im checking is the motherboard, everything else is external and relatively cheap. (relatively). a buddy of mine is lookin to pick up a cdma droid and this could be his new phone.
Thanks for the great write up . There are alos couple of videos out there on y-tube etc which can compliment the write-up .
bamx2 said:
Thanks for the great write up . There are alos couple of videos out there on y-tube etc which can compliment the write-up .
Click to expand...
Click to collapse
Yes, we actually have a video guide also which can be found here - How to repair a Motorola Droid X Screen
Your repair guide is very informative. Thanks for sharing :good::good::good:
moserandrea said:
Your repair guide is very informative. Thanks for sharing :good::good::good:
Click to expand...
Click to collapse
You're Welcome!
vladimirhtg said:
awesome repair guide, thanks for the info.
quick question. ive got a lovely droid x i found in a parking lot....run over. completely. most of the components (emi shields at least) look like theyre dented/pressed in but they could be in alright shape, i dunno. any insight? i could post pictures...
the entire assembly is completely worthless but i can replace all that relatively cheaply. i dont know about the esn or anything else (id rather not repair a phone that techinically belongs to asurion....)
edit: looking for a droid x to swap motherboards with, see if this one is alright. i think the main thing im checking is the motherboard, everything else is external and relatively cheap. (relatively). a buddy of mine is lookin to pick up a cdma droid and this could be his new phone.
Click to expand...
Click to collapse
Sounds like you have plenty of parts to replace. We have numerous parts for this device available on our site. A link can be found in our signature.
thank you, one addition
Thanks for this post. One extra note, the main microphone grommet is likely to fall out while you're opening the case, so work over a table and keep an eye out for it. It's a little rectangular piece of rubber with a raised hole in the middle and a
"hook-like" extensions on the sides. Looks like this:
http://www.cellulardr.com/motorola-mb810-verizon-droid-x-main-microphone-rubber-boot.html
or if that link goes stale, try an image search:
https://www.google.com/search?q=droid+x+microphone+grommet
When re-assembling, the grommet fits over the main microphone, just before replacing the lower "U-cover".
Related
Sorry about the lack of pictures. I'm an iPhone convert so I don't visit this site anymore so I didn't notice they'd gone. But to all those who didn't realise there was a PDF of the guide, I've re-uploaded the pictures from a new source so they're up again.
I've also received a lot of messages from members asking if I would repair their Elf or change the housing etc, so I just wanted to say that yes I am happy to do this (I'm in the UK), so just drop me a PM if you want.
This is a guide to illustrate how to completely disassemble the HTC Touch, including the digitizer
What you need:
T5 Screwdriver
#2 Screwdriver
Plastic opening tools
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you want to be on the safe side I’d also recommend using anti static gloves
To start, remove the back cover by pushing it upwards and sliding it off
Remove the battery and stylus
Using the T5 screwdriver remove the 4 screws at each corner of the main chassis
Remove the rear speaker at the top of the main chassis by lifting it off
To remove the front housing, use a plastic tool to get between the front part of the case and the chrome rim. Work it around the edge to release all of the catches
Now you need to disconnect the front housing from the mainboard by using a plastic tool to gently lift the connection from the mainboard
Next, disconnect the vibration part by lifting the red and black wired connection from the mainboard
To remove the mainboard from the chassis, gently pull the USB connection upwards. Once it is just out, pull it clear using the sides – avoid touching it as much as possible
To remove the camera, simply pull it away from the mainboard in the same way as the front housing separates from the mainboard
To take the LCD out, you need to first disconnect it. To do so, first remove the yellow tape that lies over the connection
Next, open the catch holding the ribbon cable in place, and pull it out
You will now be able to pull the LCD out without having the remove the LCD’s metal chassis as the ribbon will pull through the back of it
If you need to remove the LCD’s metal chassis, use the T5 screwdriver to undo the 2 screws beneath it, and it will come off
To remove the digitizer, you need to first disconnect it from the circuitboard behind the keypad by undoing the catch and pulling it out
Although not necessary, I would advise you to remove the circuitboard behind the keypad before the digitizer incase it is damaged during the process
To do this, simply remove the 2 screws holding it in place using the #2 screwdriver
Then pull the board out by levering it up with the plastic tools. This may take some fiddling but it will come out by gently pulling it while sliding it upwards at the same time
The keypad will now easily come out
To continue with removing the digitizer, push it forwards from behind by pushing on the corners. It is stuck in with a type of glue so it may feel as if it won’t come out but it will
The digitizer’s ribbon cable will then slide out of the hole on the front housing
To remove the earpiece speaker from the front housing, simply lever it up using the plastic tool or carefully with a screwdriver
The vibration part from the main chassis easily pulls out
The on/off button, camera button and the SIM and MicroSD card holder door will easily remove from the main chassis by lifting them out
To remove the speaker from the back you simply need to lever it out
This will hopefully help you to replace the housing on your device, or replace faulty parts
Good luck!
WOW! Just simply WOW! Fantastic guide man. And so much clarity by using the blue background and crystal clear pics. This shud be made a sticky. I have never seen such a thorough and clean and clear cut disassembling guide. You are surely the DISASSEMBLER guru.
Very useful if I get a Touch!
By the way, I like the IMEI in picture number 3!
EDIT: actually, 4 and 5 has an even better shot...
yeah so much clarity. this shud be made a sticky. what you say l3v5y?
I've made it sticky for now... If anyone disagrees, PM me!
l3v5y said:
Very useful if I get a Touch!
By the way, I like the IMEI in picture number 3!
EDIT: actually, 4 and 5 has an even better shot...
Click to expand...
Click to collapse
Didn't think of that one. Thanks for the heads up
(But there's no IMEI number in picture 3)
oseven said:
Didn't think of that one. Thanks for the heads up
(But there's no IMEI number in picture 3)
Click to expand...
Click to collapse
Hence the "EDIT"
I miscounted the first time...
Nice quality of pics
an alternative guide (pics not so good I think) is here:
HTC Touch
Service Manual ( not all in English)
HTC ELF_Touch Service Manual.pdf
Other Guides Service Manuals
www.mikechannon.net
I have added OSeven's brilliantly clear guide to the above site but for ease here is the link:
OSeven's Disassembly Guide - HTC Touch - Elf
Mike
ayyu3m said:
WOW! Just simply WOW! Fantastic guide man. And so much clarity by using the blue background and crystal clear pics. This shud be made a sticky. I have never seen such a thorough and clean and clear cut disassembling guide. You are surely the DISASSEMBLER guru.
Click to expand...
Click to collapse
I just remember how little information there was when I originally wanted to change my housing so it stopped me doing it until I broke my first Touch and had nothing to lose. I found one guide but it only showed as far as removing the front case...not the digitizer or anything else. But hopefully this will give newbies the confidence to try it because it's really not difficult
mikechannon said:
So erm... can I PDF it? The pics alone make it a good 'un. Full credit of course,then I can add it to the collection. There again you could do it, might take me a good while with all those pics and comments.
What dya say? - buy you a pint!
Mike
Click to expand...
Click to collapse
I think guides like this can only add to things!
I'm bored ATM so I'll turn it into a PDF if no one else can be bothered!
mikechannon said:
So erm... can I PDF it? The pics alone make it a good 'un. Full credit of course,then I can add it to the collection. There again you could do it, might take me a good while with all those pics and comments.
What dya say? - buy you a pint!
Mike
Click to expand...
Click to collapse
Go for it
I'm just finishing off something else atm but I'd be happy to do it in a bit, unless l3v5y beats me to it
Done!
Took longer than it might have as I can't code and make pdfs at the same time!
Motorola Droid 2 is fairly easy to take apart but most screws are hidden under cleverly designed stickers and hard to find. This take apart repair guide should help you take apart the Motorola Droid 2 safely, in a step by step manner, giving you a chance to replace faulty parts.
This guide should help you replace the following parts:
Motorola Droid 2 A955 Glass Touch Screen Digitizer
Motorola Droid 2 A955 LCD Screen Replacement Display
Motorola Droid 2 Replacement Battery
Tools:
T5 Torx Screwdriver
T3 Torx Screwdriver
Safe Open Pry Tool
Motorola Droid 2 A955 Take Apart Repair Guide:
The first step is to power off the phone; remove the back cover, the SIM, micro SD card and then the battery. The micro SD card slides right out with just a slight push of your finger.
The Droid 2 is held together by a number of screws. The first screws are revealed when you peel off the sticker located on the bottom of the Droid 2 as shown below. Once these screws are removed the back end of the casing will have to be gently pried off using the safe open pry tool. Just slide the pry tool in between the opening and run it along the edges of the phone.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Five pressure type contacts hold the headphone jack firmly against the camera's gold pads which allows for easy data exchange.
The speaker of the Droid 2 is held in place by the pressure of both halves of the phone's case which is why it can easily be taken off once the back has been removed. However be careful because the gold sticker you see stuck to the speaker's housing is an antenna.
Since both the antenna and data ribbon cables are too tiny to disconnect from the motherboard by hand you will need to carefully use the safe open pry tool to pull it out from it's socket.
Using the T5 Torx Screwdriver you will have to remove the screws that hold the motherboard in place after which you will need to disconnect the keypad's data cable on the flip side of the board.
If you need to replace the camera you just need to pull it out as it's a separate circuit.
Before you remove the small board located on the bottom of the Droid 2, you will first need to disconnect the antenna's ribbon cable, the vibrator motor and its control buttons. Then using the safe open pry tool the board can be easily lifted off.
You should now also be able to lift off the black rim of the phone and remove the screws that hold the sliding display in place, this should give you the first glimpse of the phone's LCD.
Before you take out the front panel you need to disconnect its cable and lift out the earpiece.
The small keyboard assembly will need to be disconnected using the safe open pry tool prior to removing the LCD.
Your Motorola Droid 2 is now completely disassembled. Replace any faulty parts to make your repairs and then follow this guide in reverse to reassemble your phone.
I'm thinking that this will be my best bet. Half the screen is dead and $20 bucks sounds a bit better than $150 for a new D2 or $200+ for another device. There literally isn't a single 4G device out right now on Verizon that I'm interested in. I'm holding out hope that when Sony and a few others release the last of their devices rumored or discussed for this year something worthwhile will drop; otherwise I'm on to T-Mobile I think.
Anyway, has anyone put in the work and done this? I've watched a video and it seems tedious more than difficult, especially some of the final steps. Any input is appreciated.
Looking a little further it seems I should probably replace the LCD while I'm at it. Still that's only about $50 for everything.
My D2 is updated to the latest firmware and I know somebody that has an older D2 with a broken screen so I'm going to try this and see if I can have a rooted D2 again
The repair is quite tedious. Not difficult, just adhesive everywhere. Use the downloadable version of this Droid 2 guide here.
bump
Do you have a fused screen assembly for this model?
Droid 2 RF board and connector locations (pics)
Here's a recent repair I performed to a defective D2, A955.
The main board holds the camera, and is the connection point for the keyboard, LCD and digitizer, as well as the SD card.
You can see how tiny the connectors are, and they ARE easily damaged if you attempt to yank them out, or force the header back into the socket.
The working result of a main board replacement.
AECRADIO said:
Here's a recent repair I performed to a defective D2, A955.
The main board holds the camera, and is the connection point for the keyboard, LCD and digitizer, as well as the SD card.
You can see how tiny the connectors are, and they ARE easily damaged if you attempt to yank them out, or force the header back into the socket.
Click to expand...
Click to collapse
Here's the working result of the main board replacement performed on a Droid 2, A955
jake.mcgee said:
Do you have a fused screen assembly for this model?
Click to expand...
Click to collapse
We do not, but you should have no problem replacing and installing the two screen by themselves.
This guide is in a step by step format and can easily be followed for a quick and safe repair for Motorola Atrix 4G. This guide will go through the steps of disassembling and replacing the touch screen digitizer as well as the LCD screen.
This guide will help you to install the following Motorola Atrix part(s):
Motorola Atrix Glass Touch Screen Digitizer
Motorola Atrix LCD Screen
Tools Required:
Adhesive Strips
T5 Torx Screwdriver
Hot Air Gun / Hair Dryer (optional)
Motorola Atrix 4G take apart guide:
The first step to disassembling the phone is to remove the back battery cover and battery as well as the sim card and memory card. You can now remove the seven torx T5 screws located behind the battery cover. With the screws removed you can now use a safe open pry tool to release the clips and flip the back housing over to the side, careful of the antenna cable still attached.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1
Use a safe open pry tool to pop the antenna cable from the motherboard and remove the back housing. Pry the motherboard up using a safe open pry tool and release the 3 flex cables underneath. Two will be pop connectors and the third is a jaw/alligator connector. Once reassessed you can now safely remove the motherboard.
Figure 2
Warm the front of the touch screen and LCD screen using a heat gun or hair dryer. Use a pry tool to slowly pry between the touch screen and rest of the phone, careful as it is still attached with a flex cable. Flip the phone over and release the pop connector and top cover.
Ease up the flex ribbon cable and also the earpiece speaker. You can also remove the black plastic and the black plastic bar.
Figure 3
You can now feed the touch screen flex cable through the housing and replace the digitizer.
Simply replace the damaged parts with the new ones and reverse the order to put your phone back together again.
Thanks for posting that. I've already replaced mine but this is as good a guide as the video that I watched. It's as easy to do as it reads. I used some locking forceps to install the third ribbon cable into the jaw connector.
Nice of you to post this guide. Not to mention, I think that it's a really classy way to respond to something said elsewhere without actually calling it out. Nice form on all counts.
Will this fix the general touch screen problem , most of the Atrix devices have.
ie.Not being able to select the first item in the men , etc
devgayan said:
Will this fix the general touch screen problem , most of the Atrix devices have.
ie.Not being able to select the first item in the men , etc
Click to expand...
Click to collapse
Yes, replacing the touch screen would fix these kind of issues.
Soft buttons
What about the lower soft buttons not working, would the replacement of this digitizer solve that issue too?
Great post! Thanks for the information.
Getch78 said:
Great post! Thanks for the information.
Click to expand...
Click to collapse
Thanks. Glad you found it useful.
I bought two screen from Amazon, non of them are fully functional......
repairuniverse, could you shed some light on the "soft buttons" issue please? Mine just stopped working and I'm thinking to replace it myself...
Thanks in advance.
rafaelbrandao said:
repairuniverse, could you shed some light on the "soft buttons" issue please? Mine just stopped working and I'm thinking to replace it myself...
Thanks in advance.
Click to expand...
Click to collapse
The "soft" buttons you refer to are part of the touch screen digitizer. Replacing this part should fix your issue.
Just replaced my digitizer...was a pain in the ass but it worked. Still need to get some tape for the screen though...really hard to put on when you can't really move the screen.
Sorry to hear you had a bit of trouble. The repair is normally pretty straight forward. Glad you got it working though.
What do you mean when you are referring to "Still needing tape" ?
Any videos on this?
PS: scratch that...
check this out:
http://www.youtube.com/watch?v=kxuF_73YIIY
repairsuniverse said:
Sorry to hear you had a bit of trouble. The repair is normally pretty straight forward. Glad you got it working though.
What do you mean when you are referring to "Still needing tape" ?
Click to expand...
Click to collapse
I didn't use any tape under the screen because I didn't have any good one. I ordered some double sided tape on eBay.
Will have to take it all apart again and restart by putting the tape first, then the digitizer cable through the hole, then the LCD, and finally the digitizer...that's why its a pain.
Sent from my MB860 using XDA
What kind of tape is needed, if any? I see a screen replacement in my near future and want to make sure I have everything before I start.
Sent from my MB860 using XDA
nsaia said:
What kind of tape is needed, if any? I see a screen replacement in my near future and want to make sure I have everything before I start.
Sent from my MB860 using XDA
Click to expand...
Click to collapse
2 mm double sided
Sent from my MB860 using XDA
We provide adhesive tape used for these repairs on our site. Great question!
I'm having an issue with my proximity sensor. It doesn't seem to respond all the time and its on the "block state"...so when I place a call the phone goes black. If I press on the top of the phone near the sensor, it starts working for a couple minutes, and then goes black again.
Any ideas? Did I block something (don't think so)? Bad connection somewhere?
Nice guide. I was just looking to clean my front facing camera, so this will work great for that
Zero-K said:
Nice guide. I was just looking to clean my front facing camera, so this will work great for that
Click to expand...
Click to collapse
Glad we could help!
The issue:
I got one of the very early Nexus 9. My device was mostly fine (no huge light-bleeding) but the Power and the Volume-Up buttons were hard to press because they were not raised high enough above the surface.
(Volume-Down was working fine)
Tools required:
Tweezers, a small Phillips screwdriver and something to open the device. (I used the iFixit Toolkit)
1 piece of paper (regular printer paper, post-its, ...)
Disclaimer:
If you follow my instructions you do this at you own risk. I'm not responsible for any damage you do to your device.
The mod:
Take of the back cover of the device. (https://www.ifixit.com/Teardown/Nexus+9+Teardown/31425)
(Edit)
Shortcut: It is also possible to improve the buttons without removing the whole button frame. See post #3 for details.
Click to expand...
Click to collapse
Remove the 3 screws (red) and the big connector (green).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Pull out the metal body holding the buttons. Pull carefully on the button cable to remove it from the connector.
If you look closely you can see that the Volume-Down button is not completely attached to the metal frame. This looks like a production error but it allows the button to be pressed normally.
We could apply this "production error" to the other buttons too which should improve their usability.
First separate the buttons from the metal frame. I found that only a piece of paper is thin enough to not cause damage to the buttons.
Now, use the same piece paper (or another one - I don't care ) to create tiny pieces that can be put behind the buttons to raise them a bit. (I folded the paper once to have 2 layers)
Carefully put everything back together.
Results:
All buttons work fine.
This is amazing! I was thinking I should open the nexus 9 to see if there was anything I could do to fix this. Good to see I wasn't the only one who had this thought
I will try it out tomorrow morning. Thanks.
Edit:
I've done it, and it definitely improved the buttons. I used 4 layers of paper since your piece of paper was so thick.
I think overdid the volume down button though, because it's not as clicky as the others. My buttons were all glued on properly unlike your volume down button, so I put a little extra under it.
Might go ahead and fix sometime later if it bothers me. The buttons could still be better, but this fix makes the best out of what we got. Mine is a 32gb HT4AHJT which is built mid october, so the buttons aren't sticking out as much as the later versions. The screen is so good though that I don't want to replace it because of the buttons. Thanks the tutorial man, it really made this fix easy.
Hi! Thanks for your tutorial. You inspired me, and i fixed my buttons in the similar, but i think, simpler way.
After opening a back cover, you don't have to take out buttons from tablet. Also you don't have to separate buttons from metal frame.
I think that simplest solution is to put folded pieces of paper between buttons (these on tablets cover) and that black thing with metal frame, which you were pulling out.
I attach pictures showing what i mean.
Yeah I tried this first too but somehow it did't work that well for me. Nevertheless its worth trying the simple way before pulling out the whole button assembly.
Kubens1pl said:
Hi! Thanks for your tutorial. You inspired me, and i fixed my buttons in the similar, but i think, simpler way.
After opening a back cover, you don't have to take out buttons from tablet. Also you don't have to separate buttons from metal frame.
I think that simplest solution is to put folded pieces of paper between buttons (these on tablets cover) and that black thing with metal frame, which you were pulling out.
I attach pictures showing what i mean.
Click to expand...
Click to collapse
I also did this and it worked great!
THANK YOU!
Just did this and buttons work great now.
this reminds me of the n7.1 screen raising issue using pill pack foil as washers for the screen screws, that works to this day since the wife is happily using my old n7 right now. I'll be trying a variation of this paper or plastic fix in the near future...
HTC should just send us a new button mount for early adopters.. I have 0 screen bleed, but shallow buttons. guess what I can live with.
Sent from my Nexus 9 using Tapatalk
I got an early device also, one question though.
when opening the back cover, and replacing it on... does the back cover feel loose and flexes more now?
there were reports early on that pulling the back off then replacing it on makes it more floppy....
Gezzaman said:
I got an early device also, one question though.
when opening the back cover, and replacing it on... does the back cover feel loose and flexes more now?
there were reports early on that pulling the back off then replacing it on makes it more floppy....
Click to expand...
Click to collapse
The cover does wear on the clips that hold the back to the aluminum sides... If you remove the back too many times you'll wear away the plastic clips and will damage the seal...
Ive taken mine apart about a dozen times... There's 2 places where I need glue now.. [emoji23] [emoji26]
Gezzaman said:
I got an early device also, one question though.
when opening the back cover, and replacing it on... does the back cover feel loose and flexes more now?
there were reports early on that pulling the back off then replacing it on makes it more floppy....
Click to expand...
Click to collapse
I opened my device twice now.
After the first time the back cover flexed significantely more on the surface than before. When closing it the second time i pressed firmly on the whole surface BEFORE I pressed the edges back together. There are clips across the surface that snap in place more easy when you do it before snapping the edges back together.
Now the back cover has nearly no flexing at all - even less than in its original state.
Thanks for posting this. Can you please help me understand how the camera is attached to the back cover. From the iFixit video, they mentioned that the camera came off with the back cover and that it was attached to the underside of the mother board... eeek! I don't want to screw something up like the camera while trying to fix the buttons.
What should I watch out for as I remove the back cover?
Thanks!!
-Jason
There is a small amount of double-sided adhesive tape around the camera. On my device the camera did not come of when removing the back cover - I guess it sticks a little bit different on every device.
lfrst05 said:
There is a small amount of double-sided adhesive tape around the camera. On my device the camera did not come of when removing the back cover - I guess it sticks a little bit different on every device.
Click to expand...
Click to collapse
Mine also had the camera still connected after pulling the back cover off.
I remember doing this with my Nexus 5. Thanks for the tip.
I did this and the buttons are great now. Thanks for the MOD.
I didn't pull the back all of the way off, it was held on by adhesive. I think it was a fix they introduced. My Nexus 9 is about perfect now.
-Jason
Yep, pulled my camera off. =-O
I guess I'm tearing into it more than I expected.
My buttons are perfect though. Thanks for the tip. I used 3 layers of standard paper.
This really is amazing. I just did it on mine. Really really simple fix. Unbelievably simple. I didn't even have to pull the whole back off. Just the top and sides were enough.
3 layers of paper under each button and they are now perfect. Thank you!
liquidsuspension said:
Yep, pulled my camera off. =-O
I guess I'm tearing into it more than I expected.
My buttons are perfect though. Thanks for the tip. I used 3 layers of standard paper.
Click to expand...
Click to collapse
Did you or anyone else who pulled the camera off got it back working?
Did you follow the ifixit guide to tear it apart until you were able to remove the motherboard and reconnect the camera, or is it possible to do it without removing the battery and the copper fold (being extremely careful not to break it, of course).
And yes, I did pull my camera off. It was firmly glued to the plastic cover :\
Edit: from what I see in the ifixit teardown and from what I see in mine, it does seem that if I remove the front camera cabling and the battery cable It might be ok to remove the T5 screws and raise the mobo just enough to be able to pry open the camera connector, insert the camera ZIF, close/press the connector and reatach the mobo wihtout having the hassle to unglue the battery, remove all the copper foils etc etc...
Anyone has had a similar experience?
I had to tear mine completely down to get the mobo out. I tried to reconnect it without removing it, but it was a lost cause. The worst part for me was getting the battery disconnected. There wasn't any natural way to do it as far as I could tell. If you try to just lift the edge of the mobo enough to connect the camera, be incredibly careful, but from my experience I doubt it can be done that way.
Thanks for the answer, although it's not what I was hoping for... this afternoon I started removing the battery and quit because I was afraid I was going to break something. That stuff is completely glued and it requires a lot of pressure to start separating it from the body
One day I will get tired of not having a camera and will try to do it by just lifting the mobo edge.
Quite honestly, this damn nexus has brought me too much trouble already...
So I dropped my phone and broke the front glass. LCD works but not touch-screen so pretty much useless. I decided to take it apart first to see how hard it would be to replace the screen as I could see screens can be bought from AliExpress for about 65 USD or 99 USD from elephone.hk.
Took some pictures along the way as I couldn't find any images of the internals of this phone online so this might help someone trying to replace their screen or just thinking about it.
1) Back cover - this comes off rather easily once you get something between the edge and start nudging the clips to open. Notice that the whole back cover is glued a bit to the battery so even after getting all the edges open I still had to use some force to remove it from the battery. PS: The side-buttons are attached to the cover also so try not to hurt those while removing the back.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2) Next I removed the bottom half cover to see if I could access the screen cables from there. Notice that the black ribbon that goes to the screen is the home button LED light and cannot be removed without unsoldering it!
3) I took off the top cover and unhooked the battery.
4) The battery - It's glued to the metal frame using 2 strips of glue and it took me 10 minutes to get it out safely without damaging it (it's soft so you can probably easily make it explode in your hands).
5) Took me some thinking but I removed the whole main board. The bottom side is glued and I had to break some black "paper" to get it out.
6) Screen - After getting the main board out I had enough room to force the screen out. Notice that the screen is glued from the top and bottom but sides are not glued. Some sensor cable from the front panel is glued to the camera's LED lights. The speaker was a bit hard to take out and I managed to break one of the soldered cables for that :S The bottom of the screen was glued on extremely hard.
Some notes: You definitely need to remove the battery as the screen cable runs underneath it. I'm not certain you need to remove the main board as it seemed you might be able to replace the front screen without taking that off. There's a lot of glued stuff in there so you better have good tools to pull things apart without breaking it.
So finally after having taken it apart enough and asserting a few things I decided that replacing the whole screen and re-building it will take too much time. I just saw a deal for $199 with wireless charger included. So having a choice of $65 new screen + 4 weeks of waiting and then spending 2 hours trying to replace it or buying a new one for $199 and getting a wireless charger + extra USB-C cable - I just ordered a new one. Plus I get to keep the old phone parts around for spares in case any of the side-buttons or front-speaker etc break
Just a note - my phone was in the official flip-cover when falling and got hit into the bottom right front corner and the cracks went all over the screen. I'm rather certain now that the phone's front glass panel is rather fragile and while having the silicone enclosure would've saved it in my case it's still a bit easy to break.
PS: Just wanted to add that I was actually genuinely impressed by the overall quality of the phone and Elephone in general for providing decent updates and support and assembly quality was good so while the glass panel is fragile I still decided to order a new phone from them!
Hi, I also had to replace the screen, so I tore down the phone before I ordered the new screen to see if I could do it safely. And I did (I didn't have to remove the main board, I just removed the screws and left it loose so I could remove the flat cable from the top. The problem is the screen took a couple of weeks to arrive and now I don't remember where a couple of small metal pieces that looks like contacts go. One is golden and the other is silver, both very small, looks like they fit in something similar to the antenna connector. Do you have any ideas of where are they supposed to go?
llucax said:
Hi, I also had to replace the screen, so I tore down the phone before I ordered the new screen to see if I could do it safely. And I did (I didn't have to remove the main board, I just removed the screws and left it loose so I could remove the flat cable from the top. The problem is the screen took a couple of weeks to arrive and now I don't remember where a couple of small metal pieces that looks like contacts go. One is golden and the other is silver, both very small, looks like they fit in something similar to the antenna connector. Do you have any ideas of where are they supposed to go?
Click to expand...
Click to collapse
I cannot remember exactly either, but I think there were two of them.
One of them was visible on this pic in the top right area, above the cable that goes under the LED lights.
The other one I remember had a similar purpose, but since I packed the parts away already I cannot remember where and it would take too much time to re-piece it together to figure it out.
(Exactly the reason why I decided to go for the new one instead of replacing the screen).
xataxxx said:
I cannot remember exactly either, but I think there were two of them.
One of them was visible on this pic in the top right area, above the cable that goes under the LED lights.
The other one I remember had a similar purpose, but since I packed the parts away already I cannot remember where and it would take too much time to re-piece it together to figure it out.
(Exactly the reason why I decided to go for the new one instead of replacing the screen).
Click to expand...
Click to collapse
I finally figured it out. Yes, I saw the one in the pic, and the other one goes in the bottom part, on the right, just below the top right screw to hold the plastic bottom part. I finally managed to assemble everything back with the new screen and it works perfectly. Thanks!
i also have to change my display screen hopefully new arrives soon and the change is not to complicated
https://www.youtube.com/watch?v=irDOXh1QoKE
And last few minutes of this showing how to remove the back cover
Hi,
I'm thinking of taking my back panel off for the purposes of fixing the GPS connections as advised here: http://bbs.elephone.hk/thread-11201-1-3.html#.V9SPfygrKM9
Now the op talks about aligning the springs with the backpanel connectors. Can someone take whichever picture is above and highlight which springs they mean?
i broke my screen on this phone, i have horizontal lines appearing on it, have tried three new screen and all display the same, i think there is a problem with mainboard after it was dropped so i am going to buy a new mainboard, anyone else experience this issue, when i wake it up its fine but after a second the lines come up, im pretty sure the screens are fine but something comes up and makes the lines
I've got this phone. I kept it in a safe place disassembled and at that time it was working, some days ago when reassembling the device, it shows no sign of life whatsoever, nor power up or charging battery; I thought the battery was completely dead, bought a brand new one but same situation... Do you think is possible that some kind of oxydation prevents the phone charging and power up? If connected to PC via usb cable, it shows Mediatek Preloader, so I think the phone is not dead.... Thank you all for answering, regards.