Tell me your perfect ICS-Kernel settings - Galaxy S I9000 General

Tell me your perfect ICS-Kernel settings
So I' ll beginn :
Semaphore 0.9.7bm
Over/Underclocking : 1200mhz
Governors : smartass V2
Schedulers : Simple I/Q
Deep Idle is on
Sent from my GT-I9000 using ICS-Slim

Slim 2.9
Pawitp
Deep idle on
OneDemand - Best suited for me , for most of the activities.
Next, Semaphore 0.9.5 + Smartass + simple IO (othere combinations did not give me desired results)

slim 3.0 + glitch v6
Over/Underclocking : 1100mhz
Governors : smartass V2
Schedulers : Simple I/Q
Deep Idle is on

Blue Lightning 1.1.0 + glitch v6
Over/Underclocking : 800mhz
Governors : GlitchOndemand
Schedulers : noop
Deep Idle is on but only top on :/

ISCSGS 4.2
Kernel: Devil 1.1.6 BF + VC
Govenor: SmartassV2
CPU:200 - 1200Mhz
Sheduler: fiops
UV: 200Mhz @ 850 (lower = reboot)
~ 1-2 h more battery at music
Gesendet von meinem GT-I9000 mit Tapatalk

WeUI v0.8.7
Kernel: Semaphore
Governor: SmartassV2
CPU:200 - 1000Mhz
Like to keep it simple!

Black Infinitium with Midnight
Smartass v2 with 1200mhz overclock

INFINITUM-v1.1.0 + glitch v6
OC : 1000mhz
Governors : Performance
Schedulers : Simple I/Q

Slim ICS 3.1
Devil2 kernel
No overclock
Conservative
SIO
Sent from my GT-I9000 using xda premium

CM9 nightly 4.0.4
Semaphore 0.9.8sbm + 720p mod (ram 399mb)
Smartass V2
Noop
Deep idle

teamhacksung CM9
Icy Glitchy
Glitchass V2
No overclock

ROM: Elite V9.1
Kernel: Devil 0.62 with BLN support
Governor: Smartsass V2
OC/UV: Stock
Deep Idle: ON

SlimICS 3.1
Devil2 0.64 CFS BLN CMC XL BM
No OC/UV
smartass V2
Noop

dark knight V3
devil 0.62
cfs
lulzactive
100-1200mhz
no uv
aokp rom control: min free ram = 75mb

ROM: CM9 last nightly
Kernel: Devil Kernel 1.1.6b VC version
Performance settings: overclock 1200 MHz. Governor: smartassV2.

Slim ICS 3.1
Semaphore 0.9.7bm
Overclocking : 1200mhz
Governors : Smartass V2
Schedulers : Simple I/Q
Deep Idle ON

ROM: AOKP Milestone 4
Kernel: Devil Kernel 2_0.64 XL (390MB RAM)
Governor: lazy
Screen off max freq: ON
Scheduler: VR
Deep Idle: ON

Slim ICS 3.1
Midnight 0.9.0-2-HUGERAM
No overclock
Conservative
SIO

Elite v9.1 Rom
Midnight Hugeram kernel Smartass governator, best setup so far
Sent from my GT-I9000 using xda premium

Slim 3.2
Devil 0.64
Lulzactive
100-1320MHz
Sio
Didle on

Related

[KERNEL] [Sense] 1.76 Ghz OCUV/VDD sysfs/EXT4/BFQ/TUN/CIFS 05/04/2011

HTC Kernel 2.6.32 (Overclocked & Undervolted)
Max 1.6Ghz (for now)
Voltage min/max 900mV-1425mV
SNQ's VDD interface (change voltages on the fly)
BFQ io Scheduler (Paolo Valente)
EXT4 support
TUN support (module)
CIFS (+utf8) (module)
NFS
You can flash from recovery (modules get pushed to /system/lib/modules/)
Download:
http://xda.richardtrip.org/thunderbolt/kernel/Thunderbolt_1766_V4.zip
SNQ's VDD interface (change voltages on the fly): http://forum.xda-developers.com/showthread.php?t=821372
GPL: https://github.com/richardtrip/mecha-2.6.32
Credits:
Jaywan (testing)
psufan5 (testing)
Leedroid
BuzzBumbleBee
Cyanogen
adrynalyne (uvoc table)
SNQ- (vdd sysfs interface)
Changelog:
V4:
Voltage changes (lower values)
apm_power: Add missing break statement
V3:
Lots of testing going on (no release).
V2:
Fixed wifi
Added SNQ-'s VDD sysfs interface for on the fly voltage changing: http://forum.xda-developers.com/showthread.php?t=821372
1.76Ghz now (don't use if your device isn't stable)
disabled smartass
V1:
Kernel 2.6.32 (Overclocked & Undervolted)
Max 1.6Ghz (for now)
Voltage min/max 900mV-1350mV
BFQ io Scheduler (Paolo Valente)
EXT4 support
Smartass
TUN support (module)
CIFS (+utf8) (module)
NFS
Just flashed, will report back.
Does this work with bamf 1.3 since his kernel is included
Sent from my ADR6400L using XDA Premium App
What were the original voltages at those speeds?
Where is the download link...
richardtrip said:
Changelog:
V1:
Kernel 2.6.32 (Overclocked & Undervolted)
Max 1.6Ghz (for now)
Voltage min/max 900mV-1350mV
BFQ io Scheduler (Paolo Valente)
EXT4 support
Smartass
TUN support (module)
CIFS (+utf8) (module)
NFS
Click to expand...
Click to collapse
Nice, thanks for sharing. Is this kernel CFS or BFS? Anyway, look forward to trying out it.
B3L13V3 said:
Where is the download link...
Click to expand...
Click to collapse
http://xda.richardtrip.org/thunderbolt/kernel/Thunderbolt_1600_V1.zip
This does work with bamf 1.3
jlevy73 said:
Nice, thanks for sharing. Is this kernel CFS or BFS? Anyway, look forward to trying out it.
Click to expand...
Click to collapse
CFS (for now)
racinwarrior said:
This does work with bamf 1.3
Click to expand...
Click to collapse
Dont think that should be a problem.
jlevy73 said:
http://xda.richardtrip.org/thunderbolt/kernel/Thunderbolt_1600_V1.zip
Click to expand...
Click to collapse
thank you sir it was down for me...for awhile
Buckling my seatbelt.....this place is gonna get crazy!
Thank you!!
Just installed it on perfect storm. It works beautifly so far!
Just ran quadrant and got a 2333! Blazing!
Sent from my ADR6400L using XDA Premium App
I had a reboot on drods 1.5, any reason to believe this will more stable at 1.6? Are the voltages more finely tuned?
Phone froze when I switched it to the smartass gov.
CyD13 said:
Phone froze when I switched it to the smartass gov.
Click to expand...
Click to collapse
Same here...IDT smartass is working properly yet. I went back to adryn's 1200 kernal...speed and batt life
I dont mean to bash on anyone as I couldnt do better myself, but I felt better performance on drods 1.5 than this one. Can someone confirm its not just me...
stevessvt said:
I had a reboot on drods 1.5, any reason to believe this will more stable at 1.6? Are the voltages more finely tuned?
Click to expand...
Click to collapse
I'm on Drod's 1.8Ghz kernel. Had a couple locks at 1.8 and also streaming media (Pandora) was skipping. Brought it down to 1.7 and its been flawless since!
CyD13 said:
Phone froze when I switched it to the smartass gov.
Click to expand...
Click to collapse
Then dont use smartass for now. Ondemand should be fine.

help,laggy problem

my phone gets laggy after installing kuro kernel.. did anyone have this problem too,or it is just me??
you must have NO FRILLS or other cpu frequency changer.
then change the max fre. to 832 then min fre. to 312
governor - smartassV2
i/o - sio
you also must root your phone
the main interest of kuro's kernel :
1. save more batteries
2. decent performance
if you want more performance install meruk's kernel
if u want performance with kuro's kernel
root ur phone and install rom toolbox
go to cpu control
chose
- powercats = lazy --> performance
- blackcats = smartassv2 --> balanced setting
- activecats = intellidemand --> battery saver
push thanks button
Cican49 said:
my phone gets laggy after installing kuro kernel.. did anyone have this problem too,or it is just me??
Click to expand...
Click to collapse
Its becoz its a battery saving Kernel so there will be some lag for sure but if u want smooth performance use no frills cpu and change your governer to other like activecats.
Cican49 said:
my phone gets laggy after installing kuro kernel.. did anyone have this problem too,or it is just me??
Click to expand...
Click to collapse
try
governer:bcm21553
sio:cfq
done!!!
enjoy your device without lag

Help: WHICH KERNEL IS BEST FOR BATTERY SAVING?

I wanted to know which kernel (and version) is the best option for battery saving purposes. Would be White kernel, kuro or merruk pre 2.0?
Without a doubt it would be Kuro Kernel.
Set as follows:
Governor: Conservative or blackcats
I/O Scheduler: deadline
Min Clock freq. : 156 Mhz
Max clock Freq. : 780 or 624 Mhz
voidvader said:
I wanted to know which kernel (and version) is the best option for battery saving purposes. Would be White kernel, kuro or merruk pre 2.0?
Click to expand...
Click to collapse
Bro try all kernels and decide yourself this is not the q to be asked....every kernel are best and good at battery saving and performances.....thanks for understanding

[KERNEL][Unofficial][Discontinued] Semaphore JB 3.0.0c with Custom Features

This is the modified version of the Semaphore kernel, JB 3.0.0c.
Since so many people were asking me for it, I've decided to share it with you guys.
Disclaimer: I will only update this kernel when I have the time. So do not ask for ETA please.
Before installing this, please take your time to read the Original OP.
This kernel contains every features that the Semaphore Kernel offers but with some additional custom features.
Features (Based on latest Semaphore)
- Linux kernel 3.0.84
- LiveOC
- Custom Voltage
- Voodoo Sound
- BLN & CM LED
- 384MB - 409MB available RAM
- Compiled with Linaro 4.7.3
- O3 optimization
- Auto brightness driver
- Touch Wake
- Vibration intensity
- Deep Idle
- USB host driver
- Governor ondemand (default)
- ondemand: sampling_down_factor tunable by momentum, smooth_ui, early_demand
- Governor conservative (module, smooth_ui)
- Governor smartassV2 (module, smooth_ui)
- Governor interactive
- Noop I/O scheduler (default)
- Deadline I/O Scheduler (module)
- Simple I/O Scheduler (module)
- ROW I/O Scheduler (module)
- CFQ Scheduler (module)
- CIFS as module
- TUN as module
- Logcat disabled (as module only)
- Standard network packet scheduler
- Kernel log buffer size 4KB (from 128KB)
- Reduced debug info
- TinyRCU
- Fast Charge support
- WiFi PM_MAX when suspend
- CWM: AROMA Filemanager
- /system/etc/init.d directory creation if not exist​
Custom Features
Swap/Zram enabled
Normal OC'd over LiveOC
1.1 - 1.4GHz
In-call Volume Hack
Voodoo Color
Entropy Tweaks
Load_freq(4*HZ+61) to avoid Loadavg Moire
arm/crypto: Add optimized AES and SHA1 routines
Backport AIO (Asynchronous IO) from Linux 3.5
Zen IO Scheduler
V(R) IO Scheduler
FIOPS IO Scheduler
IntelliDemand CPU Governor
Lulzactive CPU Governor
Wheatley CPU Governor
Linux 3.0.85
BrazilianWax CPU governor
Adaptive CPU governor
Hyper CPU governor
InteractiveX CPU governor
Lioneheart CPU governor
OnDemandX CPU governor
Lagfree CPU governor
Dynamic FSync
Massive update to IO schedulers
SLQB memory allocator
UKSM 0.1.2.2
Frandom
Plus more features to come in near future....
By installing this, you'll receive no support from Stratosk because;
This is an Unofficial Semaphore Kernel
Stratosk does not support it
So do not bug him if you have a problem with this kernel. But bug me instead!
If you guys want to see some more features added to this, feel free to tell me and I'll try my best to add them to it.
Please note that there are 3 variations:
Normal versions: for CM10 or ROMs without hugemem configuration, available RAM 384MB - 396MB
"s" versions: for Slim Bean ROM or patched ROMs with hugemem configuration, available RAM 397MB - 409MB
"vc" versions: is Voodoo Color Mod
Downloads
Normal Version (384MB - 396MB):
Unofficial_Semaphore_JB_3.0.0c​Normal Version (384MB - 396MB) with Voodoo Color:
Unofficial_Semaphore_JB_3.0.0vc_c​
S Version (397MB - 409MB):
Unofficial_Semaphore_JB_3.0.0sc​S Version (397MB - 409MB) with Voodoo Color:
Unofficial_Semaphore_JB_3.0.0s_vc_c​
Thanks to
Stratosk
kasper_h
fishears
BLOWNCO
Alberto96
And to everyone else that tested the kernel for me.
Source
Original Kernel Source
Modified Kernel Source
How to:
How to enable Swap?​
To enable Swap, you'll need to create a swap partition on you External SD card. I recommend following this guide for it. http://forum.xda-developers.com/wiki/SD_card_partitioning
1. Make sure to backup everything from your SD Card first
2. Do not reformat your SD Card while it's still in your phone, take it out and plug it to your computer through a card reader!
3. I recommend that you only create a Swap Partition around 256MB
4. Follow that guide and when you reach to Step 3, select the option "Linux Swap"
5. When you finished following that guide, plug in your SD Card to your phone and Reboot to Recovery
6. Then flash this zip Enable Swap
7. Reboot your phone and you should be good.
8. To make sure Swap is enable, go to Terminal Emulator and type "free".
9. You should see some info at the bottom about Swap.
How to Enable Zram?​
To enable Zram, go to (Settings -> Performance -> Memory management.)
Or Flash this zip Enable Zram
How to use the OC'd Steps?​
To use the OC'd Steps, use Nstools or CM Performance Settings (Settings -> Performance -> Processor -> Maximum CPU frequency.)
If the chosen Frequency setting is not sticking with Nstools or CM Performance Settings, try using CPU Control Lite or Voltage Control.
I flashed the "s" version and now 720p recording or playback is not working?​
You'll need to flash HugeMem Libs first and then you should have your 720p recording or playback working again.
How to get rid of the Green Screen Flash and get the best colour if using VC version?​
To get rid of it, I recommend using the following Voodoo Color Settings. To change them, use Voodoo Sound app (Available from the market).
Color profiles
Voodoo profile v1
Screen RGB multipliers
Red: 286xxxxxxx
Green: 333xxxxxxx
Blue: 392xxxxxxx
Screen v1 gamma hack
*Reset to 2.3.3 Then Change*
Red: -26
Green: -30
Blue: -33
Or use this gamma hack (Might get the green screen flash but with a better looking colour, thanks to aduka)
Red: -40
Green: -40
Blue: -31
*If you're still getting the green screen flash, increase the "Screen v1 gamma hack" by +4 for the red, green and blue till you stop getting the green screen flash*
Changelogs And Download Mirrors
Changelogs:
*Changes in italic are custom features*
3.0.0c (04/07/2013)
- gpu: pvr: Update to DDK [email protected]
- net: wireless: bcmdhd: Update to version 5.90.195.104
- cpufreq: ondemand: Drop early demand
- UHID built as module
- CWM: upstream updates
- new version AromaFM 1.90 (thanks to amarullz)
Changes by sUsH667 (many thanks) :
- base updated to aromafm 1.90
- deleted all languages except english
- deleted all iconsets
- deleted all fonts except roboto
- added german language
- added iconset "generic" from older aromafm-version
- added preconfigured config
- added bookmarks for often used folders: /system, /sdcard, /emmc, /sdcard/Download
- Linux 3.0.85
- BrazilianWax CPU governor
- Adaptive CPU governor
- Hyper CPU governor
- InteractiveX CPU governor
- Lioneheart CPU governor
- OnDemandX CPU governor
- Lagfree CPU governor
- V(R) IO Scheduler
- FIOPS IO Scheduler
- Remove BFQ Scheduler
- Dynamic FSync
- Massive update to IO schedulers
- SLQB memory allocator
2.9.26 (06/06/2013)
- Linux kernel 3.0.80
- ondemand: Change the calculation of frequency target
2.9.25 (14/05/2013)
- Linux kernel 3.0.78
- Auto brightness: max_lux up to 6000
2.9.23c (29/04/2013)
- Linux kernel 3.0.75
- UHID built as module
- UHID implementation (thanks to pawitp and n8r for merging it to Semaphore)
- CWM 6.0.3.1
- Updated ROW parameters (Thanks to kasper_h)
- Use XZ compression method for both Kernel and Ramdisk
- Fix Memory Leak
- More under the hood tweaks. (Check Github for more detail on commits for Apr 19, 2013)
2.9.21c (10/04/2013)
- Linux kernel 3.0.72
- binder: backport from 3.9-rc (also port some other changes to support this)
- lowmemorykiller: updates from 3.9-rc
- logger: updates from 3.9-rc
- mDNIe: suppress some debug messages (and do so minor cleanup)
- Auto brightness: calculate the average of light sensor adc values instead of normalized brightness
- Auto brightness: Intoduce max_br_threshold tunable. Over this, the brightness is updated to its max value (thanks to Necromancer3)
- Enable again android_ram_console (caused bootloops to some devices)
- Lowmemorykiller: Intoduce a white list with PIDs (up to 6) that never been killed (use: echo "PID1, PID2" > /sys/module/lowmemorykiller/parameters/w_list)
- CWM 6.0.3.0
- built with Linaro 4.7.3 201303
- add option to Semaphore Auto Brightness for parabolic function (echo 0 > /sys/devices/virtual/misc/sema_autobr/linear)
- Added frandom (much faster random number generator)
2.9.18c (02/04/2013)
- Linux kernel 3.0.71
- CWM 6.0.3.0
- built with Linaro 4.7.3 201303
- add option to Semaphore Auto Brightness for parabolic function (echo 0 > /sys/devices/virtual/misc/sema_autobr/linear)
- Zen IO Scheduler
- BFQ IO Scheduler
- IntelliDemand CPU Governor
- Lulzactive CPU Governor
- Wheatley CPU Governor
- UKSM 0.1.2.2
2.9.15c (17/03/2013)
- Linux kernel 3.0.69
- CWM 6.0.2.9
- conservative: Fix sampling_down_factor functionality
- conservative: Fix the logic in frequency decrease checking
- conservative: a minor improvement
- built with Linaro 4.7.3 201302
- remove some kernel debug messages
- KSM enabled
2.9.13c (06/03/2013)
- Linux Kernel 3.0.68
- arm/crypto: Add optimized AES and SHA1 routines
- Backport AIO (Asynchronous IO) from Linux 3.5
2.9.12c (24/02/2013)
- Linux kernel 3.0.66
- USB HID support (as module: usbhid.ko)
- ondemand: early demand feature.
- Entropy Tweaks "Should reduce some lag"; (http://lwn.net/Articles/489734/)
2.9.10c (14/02/2013)
- Linux kernel 3.0.63
- Semaphore Auto Brightness: filter sensor values for more smooth updates.
- Added 1.1GHz to 1.4Ghz OC'd Steps.
2.9.9c (08/02/2013)
- Linux kernel 3.0.62
- Ondemand: a couple of optimizations
- Auto brightness: tiny improvement
- built with Linaro 4.7.3 201301
- Voodoo Color Mod
- In-call Volume Hack
2.9.8c (06/02/2013)
- Linux kernel 3.0.60
- Semaphore Auto Brightness: use default work queue instead of a creating new one (more resource friendly). Change coding style to be Linux compliant.
- Swap/Zram enabled
- 1200Mhz OC'd added
- Initial release of the Custom Kernel of Semaphore​
Re: [Kernel] Unofficial Semaphore JB 2.9.8.c
Do you suggest any changes to voltages if running this at 1200?
Sent from my SGH-I897 using xda app-developers app
Re: [Kernel] Unofficial Semaphore JB 2.9.8.c
m1batt1 said:
Do you suggest any changes to voltages if running this at 1200?
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
By default I've increased the voltage for the 1200MHz step to 1350 mV to make sure it's stable for everyone else as not every phone is same. But once your phone is stable at 1200MHz, you can undervolt the voltage until you find a sweet spot.
Like on my phone, I was able to undervolt the 1200MHz to 1275 mV.
Sent from my SGH-I896 using xda app-developers app
m1batt1 said:
Do you suggest any changes to voltages if running this at 1200?
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
I UV by 50 with this kernel and devil kernel the same. Stable enough for me
Also. Nick0703. Sorry for posting in Stratosk thread regarding your kernel.
I was wondering how to make the 1200mhz stick. I tried through settings and then tried with nstools. No go on reboot.
Sky
Re: [Kernel] Unofficial Semaphore JB 2.9.8.c
SkyboneNoya said:
I UV by 50 with this kernel and devil kernel the same. Stable enough for me
Also. Nick0703. Sorry for posting in Stratosk thread regarding your kernel.
I was wondering how to make the 1200mhz stick. I tried through settings and then tried with nstools. No go on reboot.
Sky
Click to expand...
Click to collapse
Did you try saving the settings with NsTools?
Sent from my SGH-I896 using xda app-developers app
Nick0703 said:
Did you try saving the settings with NsTools?
Sent from my SGH-I896 using xda app-developers app
Click to expand...
Click to collapse
Yeah i made sure i deleted all my init.d/nstools/semaphore saves in recovery prior to installing as well.
Re: [Kernel] Unofficial Semaphore JB 2.9.8.c
SkyboneNoya said:
Yeah i made sure i deleted all my init.d/nstools/semaphore saves in recovery prior to installing as well.
Click to expand...
Click to collapse
I'll upload my NsTools settings and you can try that. I'll do it like in an hour. As right now I have some other stuff to do.
Edit: Check your PM.
Sent from my SGH-I896 using xda app-developers app
Hey Nick0703 would you be able to get screen off min 100mhz max 400mhz settings into the kernel or is it not really needed? I guess it sits at 100Mhz idle. Also, are you able to deep idle? BTW 1200 is optional but it wont stick on reboot still. Your settings disabled nstools to default.
Re: [KERNEL] Unofficial Semaphore JB 2.9.8.c
Try cpu control lite or voltage control if the settings do not stick.
SkyboneNoya said:
Hey Nick0703 would you be able to get screen off min 100mhz max 400mhz settings into the kernel or is it not really needed? I guess it sits at 100Mhz idle. Also, are you able to deep idle? BTW 1200 is optional but it wont stick on reboot still. Your settings disabled nstools to default.
Click to expand...
Click to collapse
I could add the screen off min 100mhz - max 400mhz to the kernel but I don't think you'll see any difference from it. But I compile a test version with that option and see if there is any difference. And yes, I'm able to deep idle. Deep idle works fine with my phone but keep in mind that not all the captivates are the same.
And for the 1200MHz, try using CPU Control Lite or Voltage Control just like sephhi stated.
Thanks guys. Good looking app but it didn't work. Not sure why. Always able to set to 1200 on devil kernel 4.1.2
Re: [KERNEL] Unofficial Semaphore JB 2.9.8.c
Version 2.9.9sc has been compiled. But it will need to go through testing first as the kernel configuration file had some few changes.
I'll need 2 people to test it. If anyone is interested, send me a PM.
Sent from my SGH-I896 using xda app-developers app
Re: [KERNEL] Unofficial Semaphore JB 2.9.8.c
Nick0703 said:
Version 2.9.9sc has been compiled. But it will need to go through testing first as the kernel configuration file had some few changes.
I'll need 2 people to test it. If anyone is interested, send me a PM.
Sent from my SGH-I896 using xda app-developers app
Click to expand...
Click to collapse
I do believe your kernel has given me better battery life! Excellent work sir!
Sent from my SGH-I897 using xda app-developers app
Version 2.9.9c uploaded.
Enjoy!
Re: [KERNEL] Unofficial Semaphore JB 2.9.9c
Great stuff Nick! Zram and 1200 smooth as butter! I'm too lazy to make a swap partition. LOL!
Sent from a heavily modded Cappy from parts unknown. Slimbean/Semaphore. FTW.
Re: [KERNEL] Unofficial Semaphore JB 2.9.9c
mrsubway said:
Great stuff Nick! Zram and 1200 smooth as butter! I'm too lazy to make a swap partition. LOL!
Sent from a heavily modded Cappy from parts unknown. Slimbean/Semaphore. FTW.
Click to expand...
Click to collapse
Thanks man! And lol making a swap partition won't take you more than 5 mins.
Sent from my SGH-I897 using xda app-developers app
Perfect. Got it to stick 1200mhz! What boot loaders do you use Nick0703? I'm wondering if i9000 loaders would help with deep idle.
Would suck if it's just my phone.
Re: [KERNEL] Unofficial Semaphore JB 2.9.9c
SkyboneNoya said:
Perfect. Got it to stick 1200mhz! What boot loaders do you use Nick0703? I'm wondering if i9000 loaders would help with deep idle.
Would suck if it's just my phone.
Click to expand...
Click to collapse
Congrats man! And I'm using stock Rogers Gingerbread Bootloaders. You could give the I9000 Bootloaders a try but I wouldn't risk it if I were you.
Sent from my SGH-I897 using xda app-developers app

[Q] Overclocking with Init.D scripts? [Defy+]

Hello. I want to know if it's possible to overclock GPU to 266MHz and CPU to:
450Mhz @ 20VSel
750MHz @ 35VSel
950MHz @ 45VSel
1300MHz @ 62VSel
without using any apps (I'm currently using Aero Kernel Control for GPU and SetVsel for CPU)... Maybe with Init.D scripts?
My Defy+ is running Slimkat 4.4.2 build 4.
Thanks.

Categories

Resources