Related
Hello dear XDA-dev members;
I had a problem this morning with my Wizard. I have a G3 device which i had downgraded to Button ROM for unlocking etc. It was working really fine until this morning. Last night i have turned off the phone radio (wireless and bluetooth was not enabled)and the battery was charged almost at %60.
This morning i woke up, i saw that he was entered in USB recovery mode itself. (the screen with red, green, blue, with my IPL 1.0 / SPL 1.0) , i was terrified because nobody touched my phone. Then i have pushed over power button, it shut-down. I've just waited a few minutes then i've just pushed again over power button, it started with my windows mobile 5 splash screen and showing my ipl/spl. the screen is really bright at this moment but fades out, when he started to fade out, he just shut-down itself.
I've read and searched over the forum, and though that it was my battery which was dead. I've plugged it with wall charger and waited almost one hour, and the charger led was red. I've tried to turn on, he just came on and go over my Today screen! and the charger led turned to green. Almost 45 seconds later the phone turned off itself. I've tried to re-start but it's same. I'm getting windows splash screen, and the screen brightness starts to fade out and the phones shuts down.
I've tested my battery with a volt-meter, i'm getting 4.86 volts. i have also checked power pins inside the phone, i'm also getting power there (4.6 volts) when it's connected with wall-charger, so i think that it's fine.
I have tried to hard reset, pushing communication + voice command button + soft reset button, i had the black screen, he said that it was ok, but same here. I was running with Button rom as i said before. (1.05)
Please help.
if you still can get into bootloader, it should be fine
It was entered into bootloader mode itself. When i'm trying to start it, the splash screen comes on, it shows WM5 and my IPL/SPL and 20 seconds after, it shut down. I really need help because it's my only phone that i own.
etron45 said:
It was entered into bootloader mode itself. When i'm trying to start it, the splash screen comes on, it shows WM5 and my IPL/SPL and 20 seconds after, it shut down. I really need help because it's my only phone that i own.
Click to expand...
Click to collapse
Have you had your phone more than a year? It may be the battery.
Replacement batteries cost only $5 on ebay or Amazon. Just get a battery so you can be sure that isn't the problem. In any event, you will probably need a new battery so you may as well try this.
joihan777 said:
Have you had your phone more than a year? It may be the battery.
Replacement batteries cost only $5 on ebay or Amazon. Just get a battery so you can be sure that isn't the problem. In any event, you will probably need a new battery so you may as well try this.
Click to expand...
Click to collapse
I've gone to buy a new battery, but it's the same thing. It just shuts-down irregullary at splash screen, or today screen.
Some faults in memory result in the device needing to soft reset in an attempt to reclaim memory. Perhaps you could try flashing to another rom. I dont own a g3 so I cant really advise you any further.
Mine not exactly like you but automatic bootloader or stuck at IPL screen. It was out of nowhere but thought a bad flash. When trying the hard reset, it would come as "failed".
Nearly threw phone thinking too old and dead but this came to rescue. http://forum.xda-developers.com/showthread.php?t=276963. If not tried, give it a shot.
WARNING: Use card reader to save your MINISD data's and if successful, first format card before reinserting.
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Im guessing you cant run bootloader?
Maybe this is a warrenty jobby
If you know someone with another HD2, Try swapping the battery.
chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
does it enter in bootloader mode?
retry flashing wm rom+radio
chrisizzle492 said:
i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
Click to expand...
Click to collapse
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
shufflez said:
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
Click to expand...
Click to collapse
i have restarted many times.
i use the wall charger.
but why would the phone boot but not turn on the screen or have the mic work?
remove your sd card and the battery. you may have to hit the rest button on the back after you plug the battery back in as well, but as long as you have the sd card out it should come back on. try plugging the phone into a charger and then remove the battery as well sometimes it'll wake it up so to speak. it's just a matter of playing with it. mine did the exact same thing and i freaked out for a little bit.
now if after all this it doesn't work and you've played with it for a while then yeah, best of luck to you =\. but whatever you do in playing with the battery and the charger, keep the sd card out until you can boot into winmo.
EDIT: never mind, i thought the phone wasn't booting. i misunderstood, but i went back and reread the original post. try reflashing your rom if you're in winmo and experiencing those issues. or take the sd card out and reboot.
i would suggest making an backup, as your phone turns on you should be able to estaplish a remote-connection with some (3rd-party-)software and do a hardreset.
if this wont work i would recommend setting it back to factory default (revert hspl if you have one and install stock rom) and send it in for warranty.
seems to be some major problem...
All this steps should be possible without screen turning on (working touchscreen may be needed for backup, but flashing doent need screen input)
if drive-mode is default for your usb connection and holding you from flashing you can do a hardreset and afterwards active sync will be default again and you can establish an active sync connection and flash
check if any of the pins that contact the battery are bended or broken, try to avoid removing the battery when you have to reset your hd2 because the pins are fragile
similar thing happened to me just last night!
I tried the jmz dual boot last night and I was nearly out of battery. I didnt look at any instructions I just installed it and restarted the phone to check out the new toy. it finally got done loading I chose android right away and I was walking towards the bedroom. when I went to see if android had fully booted and plug in the phone I had nothing! It was off. I decided that the battery must have died so I tried to turn it on and all that happened was the tmobile flash screen came up for a second and then it went right off, I got so desperate that I was going to do a hard reset but that wouldnt even work! the boot loader screen would just shut right off. I was suggested to try another battery we had at the house and bang it fired right up I took a wiff of my other battery and I dont know what happened but I think I let the magic smoke out cuz it is fried!
chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
hello friend...i have a problem similar to this. basically when my phone is in android which i use alot if it dies in android, when i reboot it it will turn on for about a second to see my splash screen then turn itself off (the battery is obviously flat). so i plug my charger in and it stays on now but doesnt indicate charging....i boot it into windows mobile and the batt just stays at 0% but its still working. however once i unplug it it will die.....its like the battery is not in the phone. luckily i have two batteries and a dock which charges batteries, so i replaced the battery and everything works fine. once the battery that died in android was fully charged i tried it again and it was fine.................im guesing the moral to this story is dont let your phone die in android mode
I do notice my HD2 runs hotter while in android than while it runs in Windows.
I am not sure if that's an issue to this, which is why I never mentioned about it being hotter. Although my HD2 is noticeable hotter, it never gets to a point that I think I should unplug the USB due to overheating concern...
Just a few inputs from passed experience
I use TMOUS Stock 2.13.531.1 WWE ROM
2.12.50.2_2 radio (not stock)
k going to tmobile today to see if they have any extra batteries i can try.
then ill update
i went to tmobile. and while i was there i noticed the screen was turning on but very dim without backlight (barely noticable). but the rep helping me did not notice and i let it stay that way because tmobile is sending me a new refurbished phone as long as i send the old one (and the rep was totally cool he uses xda also and said they wont check my software and if they do they wont ask for the phone back). he also let me get insurance in case this happens again, instead i will just say its lost. so i basically killed 2 birds with one stone
I was using my phone like a normal person texting, using the web, watching youtube, then my battery died so when I went to recharge the phone it just stays looping at the "Stick Together" screen, so is my phone bricked? Or could it be the battery? I dont have another battery to try it out! Please Help!!!!
King Royalty said:
I was using my phone like a normal person texting, using the web, watching youtube, then my battery died so when I went to recharge the phone it just stays looping at the "Stick Together" screen, so is my phone bricked? Or could it be the battery? I dont have another battery to try it out! Please Help!!!!
Click to expand...
Click to collapse
Odds are that one of your battery connection pins are bent. Check them closely, there should be 5 of them, like this, all straight and even:
ll l ll
if its not a bent pin, it could simply be that it isn't able to start because the battery is so flat, but every time you plug in the cable it turns itself on, thus preventing it from starting to charge.
Take teh battery out, plug in the USB, and then put teh battery back in. It should start to charge (after a pause, sometimes) without trying to power on.
samsamuel said:
if its not a bent pin, it could simply be that it isn't able to start because the battery is so flat, but every time you plug in the cable it turns itself on, thus preventing it from starting to charge.
Take teh battery out, plug in the USB, and then put teh battery back in. It should start to charge (after a pause, sometimes) without trying to power on.
Click to expand...
Click to collapse
Yes, and make sure you're charging on a wall outlet rather than on a PC USB port, you'll get a much higher current that way.
If your phone still won't boot, with all the other suggestions, you will have to hard reset it. (I have had to do so twice already, after just having had the phone a couple days!)
Make suire it is completely off. Press and hold in both the Volume Up and Volune Down buttons. While holding them, press and release the red End button. (But keep holding down the two power buttons.)
Until--you get a message about the hard reset. Then you can release those two buttons, and follow directions on what to do next.
Any data, settings, etc. on the phone (not the storage card) is lost in a hard reset. Fortunately, both times I had recent backups to restore from, after the hard reset. (Moral--back up often with this phone.)
Thanks for your help guys!!! It was the battery connectors that were bent, everything is all good now!
King Royalty said:
Thanks for your help guys!!! It was the battery connectors that were bent, everything is all good now!
Click to expand...
Click to collapse
No problem, it's one of the most common causes of that problem, but not the only one.
I think samsamuel and I are going to start a pool every time that question gets asked
hah, if only we'd started 6 mths ago
My HD2 doesn't turn on, doesn't go into boot loader, and cant soft reset. Can I officially say i bricked my HD2? And i cant even get it replaced because the camera is somehow cracked, and that supposedly "voids" the warranty.
And Im quite sure you need a JTAG to fix it, correct?
if it was a 51 radio brick, then yea, JTAG is it.
actually, it wasnt a 51. radio brick. I installed the Eugenia Rom through CustomUU while my phone was connected, it installed fine, and then it wouldn't turn on?
wont turn on at all? nothing? black screen? no charge light?
check the battery pins.
Nope, nothing at all. And by checking the battery pins, what should i be looking at?
just to see theyre all in a nice neat line, two one two, none bent up/down. it happens a lot.
other than a 51 radio (or 2.04.50 and 2.05.50 radios), battery pins or a discharged battery are the only reason i can think that would cause complete dead phone.
hm, I think I'm on to something here. When i plug my phone into my computer, it installs a driver. I forgot what its called, but that's all it installs. I cant access the phones files, but i thought i would let you know, maybe it could help me in the long run.
qualcomm? yea, the radio bricks show up as a qualcomm device.
try leaving the battery out for a while, (half hour) then plug in usb (wall charger, not pc) and then put the battery back in. this will stop the phone trying to run on like it normally does when you apply power when the battery is in (thus draining even the dregs of power, possibly affecting the charge circuits ability to start charging, , not very common, but not unheard of either), and with a bit of luck the charge light will appear and all will be well.
gotta go, 3am
good luck.
Thank you so much man,I'll try... ill get back to you about it tomorrow.
Erggg, nope, it didnt work =( Thanks for your time, and thank you for trying to help.
how old is it?
is it warm on the back bottom part of the phone?
Put it in the fridge for 15mins, then try to boot up.
Also see if you can try and put your battery in some one elses HD2 or charge your battery in their phone.
Its pretty hard to kill your HD2.
(i just dropped my HD2 in for a service/repair as my motherboard/cpu was overheating.- had to flash stock rom and spl back though)
I got it two weeks ago Its not warm, but ill try it in the fridge...... and I just did that a couple hours ago, we switched battery's and still no luck.
Refrigerator did not work either =/
can u do a hard reset with the volume up buttons and the power key? reformating the device to default?
Pull out ur battery, press and hold the soft reset button, hile holding down the soft reste button place ur battery back in. While still holding down the soft reset button pres and hold the volume down + the on/off swith and see if it will boot. U might need a friend to help u with holding down al the buttons. It worked for me...
Read ALL the earlier replies. Mine seems "cracked": battery won't charge in phone, via USB cables (2 cables, 2 batteries - one new & fully charged, two USB power souurces, including a car's 12v DC source).
Did all the above hard & soft resets, etc. Nothing works. Phoned HTC AUSTRALIA - MUST send it hundreds of miles (or kms) away to the original Telstra dealer, since HTC does not allow any other type of warranty claim in Australia.
On the phone's pins that contact the battery - they are flexible: up, down, in & out. Being "in-line" does not mean they work.
Not sure why the hardware crashed. Have not upgrade ROM or Android. Won't recharge the battery in-phone with SIM, micro-SD in nor out of the phone.
Wanting for a separate external battery charger (only a few $$) from eBay. Might take the phone to a dealer, and see if they can get it to recharge the battery via the USB cable.
rbadal said:
Pull out ur battery, press and hold the soft reset button, hile holding down the soft reste button place ur battery back in. While still holding down the soft reset button pres and hold the volume down + the on/off swith and see if it will boot. U might need a friend to help u with holding down al the buttons. It worked for me...
Click to expand...
Click to collapse
nope, didnt work
Hi everybody
I have a problem with my Galaxy S5 (no custom rom, official)
I normally used my phone, I locked it. But, after about 10 mins I tried to unlock my phone, but nothing happens
I tried to reboot, nothing happens. I tried take out and put the battery - nothing happens. So I searched on Google and tried some keys combinations, but nothing happens. My phone has about 80% battery. I tried to charge it in the charger, but nothing is happening (black screen, no notiffication light). Also I tried to put off my SIM and SD Card, but nothing happens
Do you have some skills in it? Can you help me?
Few days ago, I faced the same problem..
http://forum.xda-developers.com/showthread.php?t=2853472
Then I'd to take it to the Samsumg store.. And they return it back in 2 days and said me it was a software problem..
I wanted to do a recovery reset, but i can't boot my phone anymore, also the Kies doesn't see anything, so. Did you really think that is a software problem? Because my phone won't vibrate at boot. So maybe it can be a hardware prob :/
EDIT: Phone started blinking red light... (nottiffication), I tried to charge it, but nothing...
Mate as mentioned early, same problem I faced..
It'll be better, if you return it to Samsung customer care..
You seem to be saying that the problem occurred unexpectedly. So presumably this isn't subsequent to a flash error, newly installed app or a trauma (dropping the phone, etc).
First ensure that your battery is charged, plug in the phone to a charger as well and try turning it on. If at all possible, borrow a battery from a friend's S5 or go to a store and borrow a battery for 30 seconds to confirm that the battery isn't the issue.
If the problem persists, then remove the cable and battery. Then put the battery back into the phone and press and continue to hold in this order, the volume down key, then menu key, then power key. Hold all three until the screen powers up (about 5 seconds). If this doesn't work.. the most likely problem is a damaged power key - try pressing hard or "wiggling" it to see if that makes a difference.
If you still can't start the phone, then see if a local cellular repair shop has a "jtag jig" that you can borrow. Or you can buy one on Ebay for a few dollars. When this jig is plugged into the USB socket, the phone should automatically restart.
If all of the above fails (which is unlikely), you would seem to have a hardware problem or unknown origin. Which would be very unusual. If your phone is under warranty, make a claim. Otherwise get an estimate to repair it.
.
If I hold all 4 buttons at the same time and connect the phone to PC, PC recognises the phone for a few seconds. Well, maybe not recognises, I cant see it, but it plays the same sound as if connected flash drive to pc. However, everytime it disconnects within a few seconds...
I´m in the same case, but I was flashing the Galaxy S5 with the four files ROM and the pit file using Odin3.09. All the process ended well, but after rebooting there apeared one Screen sayin something like "Some files at this phone are encripted and there can´t be modified......." so I did a manual reboot and take off USB cable and from this moment the phone don´t do anything but giving a sound when I plug USB to computer cable and I can see new COM --> Qualcomm HS-USB QDLoader 9008, and there repeat a loop.
I´m still looking for a solution, but it gives me that there is time to change phone.
Possible Fix
This thread is old but idk if this was ever solved, so in case anyone else ever has an issue like this. My Gf is still rocking this phone so i've had a little experience with it. The phone wont turn on or charge. I got it to work by sticking a flat head screw driver and prying it fairly hard against the bottom of the battery (the side closest to the charge port) and forcing the battery harder against the metal contacts. While pushing the battery I turn on the phone and it starts right up and continues to run even after letting the pressure off. I've noticed this happens every few times i take the battery out, but this method has never failed for me turning the phone back on. Hope someone finds this helpful.
kimo hands said:
This thread is old but idk if this was ever solved, so in case anyone else ever has an issue like this. My Gf is still rocking this phone so i've had a little experience with it. The phone wont turn on or charge. I got it to work by sticking a flat head screw driver and prying it fairly hard against the bottom of the battery (the side closest to the charge port) and forcing the battery harder against the metal contacts. While pushing the battery I turn on the phone and it starts right up and continues to run even after letting the pressure off. I've noticed this happens every few times i take the battery out, but this method has never failed for me turning the phone back on. Hope someone finds this helpful.
Click to expand...
Click to collapse
weird, youd think that bending the tabs out to force contact with the battery better would do the same trick fwif