Database Users

[Q] Semi-soft hard non-brick - just looking for ideas

Anyway, I was using Miui V3 2.4.20 [2.6.35], and Google maps wasn't very happy with it. So I decided it was time to move on to the .32 kernal version, since the developer was going that way too. Downloaded a stock rom with .32 kernal, went to the pink screen and flashed, and then boot loop.
Luckily, I'm awesome, so my phone won't die on me. Tried flashing some roms through clockwork, no bootloop, just stuck at huawei logo. Tried flashing some stock roms, and at about 98% done flashing it goes error. Some parts get flashed causing my recovery reverts to stock, but I'm still stuck at the huawei logo.
Also, in clockworkmod I get errors mounting data and emmc, so that might be a problem. Other partitions mount fine.
I'm sure I'll find a solution eventually, so there's no rush. I've been in similar situations before. Just wanted to see what other people had used for similar situations. So if you know of something that would help, please let me know.
Found these through search (I'll do a better search again later), i will try them tomorrow:
http://forum.xda-developers.com/showpost.php?p=18944228&postcount=4
http://forum.xda-developers.com/showthread.php?t=1683249
http://forum.xda-developers.com/showthread.php?t=1689469
http://forum.xda-developers.com/showthread.php?t=1682501
http://forum.xda-developers.com/showthread.php?t=1011527

After reading a lot of threads, attempting to flash a lot of roms (stock and others), replacing all kinds of images, and offering a sacrifice to the cellphone gods, still at the same problem:
To reiterate problem:
1) Stuck/reboots at Huawei logo
2) Flashing stock roms via pink screen never finish installing, get error message at ~95% finished (During install, unpacks fine)
3) Flashing roms via recovery say they installed, but still boot problem
4) This problem occurred while trying to downgrade from .35 to .32
My next step is to try using Linux to put the Dload folder on the internal SD card and try installing from there. I have a feeling it is related to the partitions having problems. I used both the "get back pink screen" and "data partition resize," maybe something went wrong with them that only appeared when I tried to go back to stock. I'll find out more when I install linux and can see if the partitions are OK or not.
I've always wanted to try linux, and now that my phone is broke I have found the motivation to do so. So a word of advice for people for people wanting to try linux but are too lazy to download the linux file: Soft-brick your phone, it gives you motivation.
UPDATE: I'm pretty sure my partition table is broke pretty bad. In adb shell, df gives me:
Filesystem Size Used Free
/dev 173M 64K 172M
/system 203M 200M 2M
/cache 127M 4M 123M
and that's it. No /HWUserData, /.cust_backup, /mnt/asec, /mnt/obb, or /data.
Would someone be as kind as to tell me how to fix the partition table? I've got a soldering iron, duct tape and super glue. Also, I'm not afraid to buy a "box" to do some Jtag stuff.

Anybody know what Blefish uses to format the phone memory? I read on his tumbler page and his github that he has altered the partition table (he split the /hwuserdata into three sections, which means he has the ability to create partitions) If I can get that tool, then I have a plan:
0) If my understanding is correct, the updates don't install because the needed partitions are missing, which causes an error. I guess the updates won't create partitions, just alter them.
1) Use the tool blefish used to setup the partition table as described in this thread: http://forum.xda-developers.com/showthread.php?t=1504488
2) Once the partitions are back, i should at least be able to get the blue screen, if I'm good, then I can put all right files in /dev/sdb1, which will get me the pink screen.
3) Using the blue/pink screen, I can install stock firmware, which should correct any problems that the partition table has. Maybe even install android.
4) Do the happy dance
5) ???
6) Profit
I've done my homework, searched the forums, made a plan, and cleaned my room. Someone please give me some feedback and at least let me know if I'm heading in the right direction.

typci said:
Anybody know what Blefish uses to format the phone memory?
Click to expand...
Click to collapse
I am using fdisk, the main partitioning tool for MBR table. You can check the table by doing fdisk /dev/block/mmcblk0 and then "p" which should print the current partition table. From there, you can also modify the partitions.
Sent from my U8800 using Tapatalk 2

Blefish said:
I am using fdisk, the main partitioning tool for MBR table. You can check the table by doing fdisk /dev/block/mmcblk0 and then "p" which should print the current partition table. From there, you can also modify the partitions.
Sent from my U8800 using Tapatalk 2
Click to expand...
Click to collapse
Awesome. I used to use fdisk back in the dos days, so I just need to brush up on my skills and learn the adb specifics. I really need to take the time to go learn all the commands associated with adb.
INTERESTING UPDATE: If I flash a rom with locked boot loader, I still get the pink screen but it doesn't work, i.e. I can't access the image folder via windows. If I flash a rom without a locked boot loader, pink screen works. Granted none of these roms actually fully flash, I still get the error near the end.
Fdisk = Permission denied, su = permission denied. Rooted boot image prevents me from getting into recovery, which means adb won't work. Any other way to get root? I'll try flashing a custom rom when I can get clockworkmod working again. For some reason I can't get recovery to load via vol+ & power.
Also something weird is going on. When it boots, it reboots once, then goes to stock recovery, tries to do a factory reset, gets errors on formating. Also in windows two removable disks appear, but I can access them. I take it that they represent the internal SD card and maybe the pink screen image folder partition. Tomorrow I'll try linux and see what happens.

UPDATE:
1) I can't use FDISK because SU won't work. I'm not sure how SU/root works on a software/partition bricked phone.
2) Rooted boot.img won't boot into recovery. SuperOneClick won't work because it can't find the data partition (probably because I don't have one).
3) I was going to try flashing a custom rom but for some reason I can't get clockworkmod working again. The phone will boot into stock recovery on it's own, after a couple of reboots. However, if I change the boot.img or recovery.img to anything else, it gets stuck at huawei logo or boot loop.
4) Unbuntu LiveCD won't work (says it can't find the kernal) even though I used the installer from the website and tried it both via cd and flash drive. Working on installing a dual-boot system now.
I'm really striking out here. Couple of questions if anyone would care to answer.
1) Besides recovery, how else can I establish an adb connection? Pink screen and huawei logo give me device not found.
2) Is there a root exploit available that doesn't require a data partition or is there a root exploit I can modify so it doesn't require a data partition? It's OK if it's a manual exploit, while I'm new with android/adb, I got plenty of experience with command prompt input from back in the dos days.
Also learned there is a HuaWei office in my town. Don't know what they do there, but if I don't make any progress after I couple more days, I'll go find out.

typci said:
UPDATE:
1) I can't use FDISK because SU won't work. I'm not sure how SU/root works on a software/partition bricked phone.
2) Rooted boot.img won't boot into recovery. SuperOneClick won't work because it can't find the data partition (probably because I don't have one).
3) I was going to try flashing a custom rom but for some reason I can't get clockworkmod working again. The phone will boot into stock recovery on it's own, after a couple of reboots. However, if I change the boot.img or recovery.img to anything else, it gets stuck at huawei logo or boot loop.
4) Unbuntu LiveCD won't work (says it can't find the kernal) even though I used the installer from the website and tried it both via cd and flash drive. Working on installing a dual-boot system now.
I'm really striking out here. Couple of questions if anyone would care to answer.
1) Besides recovery, how else can I establish an adb connection? Pink screen and huawei logo give me device not found.
2) Is there a root exploit available that doesn't require a data partition or is there a root exploit I can modify so it doesn't require a data partition? It's OK if it's a manual exploit, while I'm new with android/adb, I got plenty of experience with command prompt input from back in the dos days.
Also learned there is a HuaWei office in my town. Don't know what they do there, but if I don't make any progress after I couple more days, I'll go find out.
Click to expand...
Click to collapse
On pink screen, your device is just like any other mass storage device. So you can still use fdisk on ubuntu with the correct /dev/sdX path. You can also format the data/system/cache using other tools if you need to.
Sent from my U8800 using Tapatalk 2

Sweet, so I just need to get Unbuntu working. I still can't figure out why the live CD/flash drive didn't work. Oh, well. When I get off of work I'll get to installing the dual-boot system. Thanks for your help.

typci said:
Sweet, so I just need to get Unbuntu working. I still can't figure out why the live CD/flash drive didn't work. Oh, well. When I get off of work I'll get to installing the dual-boot system. Thanks for your help.
Click to expand...
Click to collapse
i actually understood nothing from your posts but i would like to congratulate you for being a user who does research before asking ppl something
and I gladly give you a bump

JaymzBond said:
i actually understood nothing from your posts but i would like to congratulate you for being a user who does research before asking ppl something
and I gladly give you a bump
Click to expand...
Click to collapse
Thanks. Unfortunately the project is on hold for a couple of days. My electric motorcycle has been having some problems and I've been repairing it. Also, I think I found out why linux wasn't working. Apparently the "alternative" downloads aren't useable as a live CD, which is why the kernal wasn't there. Anyway, it's been a great learning experience. Maybe after I "break" my phone enough times I'll learn enough to become a developer.

Doing some research before getting back to working on the phone.
Looks like Blefish is talking about using linux's fdisk, when I was trying to use adb's fdisk. That would certainly allow me to bypass the su problem with adb. I think I got all the correct files for my linux livecd, so that shouldn't be a problem. After I'm done with my workout, I'll try it out and see how it goes. It's time to learn how to use linux.
Update: Got unbuntu working. Storage devices are all /media instead of /dev like I was expecting. But I think I'm not looking in the right place.
Plugged in phone via pink screen and 3 drives came up:
System - has system stupp (app, bin, etc, fonts, ...) - sdb12
256 MB File system - image folder with all the .img and .mbn files - sdb1
136 MB File system - has fotapkg, lost+found, recovery folders- filesystem type ext3/ext4 - I'm not sure what this is, maybe sdb6? If it was data (sdb13) then I wouldn't get the error in recovery, If it was the internal SD card the filesystem should be vfat. If someone knows better, please let me know.
For some reason I don't have permission to access the lost+found folder, or so Unbuntu tells me.
Tried to used fdisk with system, got error: I don't know how to handle files with mode 40755
Also found some recovery log files in the fotapkg and recovery folders. I'll post it here incase someone can get some more useful information out of it. Does anyone know what all these (null) mean?
Tomorrow I'll get to work on learning how to use unbuntu and fdisk.
Starting recovery on Sun Jan 6 00:03:50 1980
can't open /dev/tty0: No such file or directory
framebuffer: fd 3 (480 x 800)
recovery filesystem table
=========================
0 /tmp ramdisk (null) (null)
1 /boot vfat /dev/block/mmcblk0p1 (null)
2 /fat vfat /dev/block/mmcblk0p1 (null)
3 /cache ext4 /dev/block/mmcblk0p6 (null)
4 /data_pseudo ext4 /dev/block/mmcblk0p13 (null)
5 /misc emmc /dev/block/mmcblk0p7 (null)
6 /recovery vfat /dev/block/mmcblk0p1 (null)
7 /HWUserData vfat /dev/block/mmcblk0p14 (null)
8 /system ext4 /dev/block/mmcblk0p12 (null)
9 /sdcard vfat /dev/block/mmcblk1p1 /dev/block/mmcblk1
I:cmdline: console=ttyDCC0 androidboot.hardware=huawei androidboot.localproppath=hw/default androidboot.emmc=true androidboot.image=recovery androidboot.mode=user androidboot.baseband=msm
Ita_move_command_file
I:Got arguments from boot message
Command: "recovery" "--wipe_data" "--wipe_cache"
Formatting /cache...
Creating filesystem with parameters:
Size: 136314880
Block size: 4096
Blocks per group: 32768
Inodes per group: 4160
Inode size: 256
Journal blocks: 1024
Label:
Blocks: 33280
Block groups: 2
Reserved block group size: 15
Created filesystem with 11/8320 inodes and 1585/33280 blocks
E:failed to mount /data_pseudo (No such file or directory)
E:failed to mount /data_pseudo (No such file or directory)
Formatting /data...
Need size of filesystem
E:format_volume: make_extf4fs failed on /dev/block/mmcblk0p13
E:failed to mount /data_pseudo (No such file or directory)
E:failed to mount /data_pseudo (No such file or directory)
Formatting /cache...
Creating filesystem with parameters:
Size: 136314880
Block size: 4096
Blocks per group: 32768
Inodes per group: 4160
Inode size: 256
Journal blocks: 1024
Label:
Blocks: 33280
Block groups: 2
Reserved block group size: 15
Created filesystem with 11/8320 inodes and 1585/33280 blocks
Data wipe failed.
wipe internal sdcard fail.

It could be that the data partition (originally mmcblk0p13) got wiped out and now mmcblk0p13 is internal sd card. Here's the original partition table:
Code:
Disk /dev/block/mmcblk0: 3959 MB, 3959422976 bytes
1 heads, 16 sectors/track, 483328 cylinders
Units = cylinders of 16 * 512 = 8192 bytes
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 1 30721 245760 b Win95 FAT32 CUST
Partition 1 does not end on cylinder boundary
/dev/block/mmcblk0p2 * 30721 30783 500 4d Unknown SBL1
Partition 2 does not end on cylinder boundary
/dev/block/mmcblk0p3 30783 31158 3000 46 Unknown TZ
Partition 3 does not end on cylinder boundary
/dev/block/mmcblk0p4 31158 483328 3617363+ 5 Extended EBR
Partition 4 does not end on cylinder boundary
/dev/block/mmcblk0p5 32769 34304 12288 59 Unknown OEMINFO/BOOTLOADER IMAGES
/dev/block/mmcblk0p6 40961 57600 133120 4c Unknown CACHE
/dev/block/mmcblk0p7 65537 65599 500 5a Unknown MISC
/dev/block/mmcblk0p8 73729 74112 3072 58 Unknown FSG?
/dev/block/mmcblk0p9 81921 82795 7000 50 Unknown ADSP
/dev/block/mmcblk0p10 90113 90496 3072 4a Unknown MODEM_ST1
/dev/block/mmcblk0p11 98305 98688 3072 4b Unknown MODEM_ST2
/dev/block/mmcblk0p12 106497 134656 225280 83 Linux SYSTEM
/dev/block/mmcblk0p13 139265 216064 614400 83 Linux USERDATA
/dev/block/mmcblk0p14 221185 483328 2097152 69 Unknown INTERNAL_SD
The sdb6 is indeed cache, and it is used for recovery communication between Android.
If everything would be ok, it would mount sdb1, sdb6, sdb12, sdb13 and sdb14 inside Ubuntu, so it seems that something is wrong at the end.
If you have 14 partitions, use disk utility from Ubuntu and try manually formatting the 13 for ext4 and 14 for vfat. Taking ownership is not needed, it should work either way.

Blefish, thanks for the help. Got unbuntu up and working along with fdisk and identified the phone.
I have 13 partitions (including one empty one) , not 14. Here's the print out:
[email protected]:~$ sudo fdisk /dev/sde
omitting empty partition (13)
Command (m for help): p
Disk /dev/sde: 3959 MB, 3959422976 bytes
1 heads, 62 sectors/track, 124729 cylinders, total 7733248 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sde1 1 491520 245760 b W95 FAT32
/dev/sde2 * 491521 492520 500 4d QNX4.x
/dev/sde3 492521 498520 3000 46 Unknown
/dev/sde4 498521 7733247 3617363+ 5 Extended
/dev/sde5 524288 548863 12288 59 Unknown
/dev/sde6 655360 921599 133120 4c Unknown
/dev/sde7 1048576 1049575 500 5a Unknown
/dev/sde8 1179648 1185791 3072 58 Unknown
/dev/sde9 1310720 1324719 7000 50 OnTrack DM
/dev/sde10 1441792 1447935 3072 4a Unknown
/dev/sde11 1572864 1579007 3072 4b Unknown
/dev/sde12 1703936 2154495 225280 83 Linux
Comparing with your partition table I see two differences:
1) the ending block of sde1 is 491520 on mine and on the original it is 30721, however the blocks are the same, so that is probably not a problem
2) sde13 is empty, and sde14 is missing.
This actually makes sense. When I was using MIUI, I reduced the size of the internal sd to near zero, since MIUI could only either the internal or external sd, not both. After trying to downgrade, I had a problem, so I tried to restore the internal sd card back to stock size, just to bring my phone back to stock. Something must have gone when I did that.
So if I understand the problem correctly, to fix this I need to:
1) Split sde13 into 2 partitions
2) Format sde13 to ext4 and sde14 to vfat
3) Try installing adroid again
Do I need to name the partitions a certain name or do anything else?
In the mean time I'll be looking into how to use disk utility and fdisk to deal with sde13 and sde14.

Had an idea that I only need sde13 (data) to get things working again, the system shouldn't need sde14 (internal sd) to work.
So I went to disk utility, found Qualcomm MMC storage and tried to format the free 2.9GB at the end. Got an error:
Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sde, start=1103101952, size=2856000000, type=0x83
Entering MS-DOS parser (offset=0, size=3959422976)
MSDOS_MAGIC found
looking at part 0 (offset 512, size 251658240, type 0x0b)
new part entry
looking at part 1 (offset 251658752, size 512000, type 0x4d)
new part entry
looking at part 2 (offset 252170752, size 3072000, type 0x46)
new part entry
looking at part 3 (offset 255242752, size 3704180224, type 0x05)
Entering MS-DOS extended parser (offset=255242752, size=3704180224)
readfrom = 255242752
MSDOS_MAGIC found
readfrom = 255243264
MSDOS_MAGIC found
readfrom = 255243776
MSDOS_MAGIC found
readfrom = 255244288
MSDOS_MAGIC found
readfrom = 255244800
MSDOS_MAGIC found
readfrom = 255245312
MSDOS_MAGIC found
readfrom = 255245824
MSDOS_MAGIC found
readfrom = 255246336
MSDOS_MAGIC found
readfrom = 1140842496
No MSDOS_MAGIC found
Exiting MS-DOS extended parser
Exiting MS-DOS parser
MSDOS partition table detected
containing partition table scheme = 1
got it
Error: Invalid partition table on /dev/sde -- wrong signature 0.
ped_disk_new() failed
So, my partition table is corrupt? I'll need to figure out how to fix this.

Here's some options I've found:
http://forum.xda-developers.com/showpost.php?p=21572216&postcount=12
ksatta mentions a couple of ideas:
1) If someone backed up their phone using dd, I could use that to restore my phone.
Here's a link on how to do it: http://linuxpoison.blogspot.com/2009/04/creating-backuprestore-images-using-dd.html
dd if=/dev/sdX | gzip > /home/sdX.bin.gz
where sdX is the U8800
2) I could clone someone's partition table. If someone could give me a copy of their MBR that should work.
Here's a link on how to do it: http://embraceubuntu.com/2005/10/20/backing-up-the-mbr/
Create a backup of your MBR by doing a:
dd if=/dev/sdX of=MBR-backup bs=512 count=1
That should read “create a disk dump of the input file, which is /dev/sdx (change to hda, or hdb or sda, depending on where the MBR is on your computer), and save it in the output-file MBR-backup in the directory from where the command is issued. Backup the first sector only, while you are at it”.
3) gparted - it's some kind of partition tool. Might be able to use it to fix the error. Not sure how to use it though.
For now I'm going to look into gparted for Ubuntu. If someone can help me out with a dd backup or cloning the partition table that would be awesome.
UPDATE: For people following this thread, and to keep me more organized, I'll start adding more of the important resources I find. They may one day help you fix your phone.
https://bugs.launchpad.net/ubuntu/+source/gparted/+bug/434463
Seems a guy fixed his the same error with gparted. However it wasn't on a phone. Also I'm seem a lot of people refer to sfdisk. I'll need to learn more about it.
https://answers.launchpad.net/ubuntu/+question/113539
"I got an answer in a forum, which looks easy.
Do a
sudo fdisk /dev/sda
then type
w
to write partition table, without any modification of it.
The signature should be fixed."
Is this safe to do to my phone? I know I'll have to write the MBR eventually, but I have to get it right the first time. If I screw up, I may not be able to connect to ubuntu anymore. Anyway, the guy said it fixed the error with his harddrive, so it's worth a try.
http://www.thegeekstuff.com/2010/09/linux-fdisk/
How to use fdisk, in case anyone needs to know
So my new plan is to:
1) dd Backup and MBR backup - in case I break it worse than it is
2) try to fix with fdisk w or gparted

I think the change in start and end is caused by Ubuntu using cylinders/sectors/blocks. Should not too much difference though.
Using MBR restore would not work here, as it restores the main 4 partitions list. MBR uses EBR aswell, which is located at the beginning of every extended partition. So we would have to copy the EBR of every partition.
I'd suggest deleting sde13, adding sde13 and sde14.
When adding sde13, note that starting block should be at the end of sde12, so simply insert last block of sde12 there. If it gives error, simply press enter as it automatically finds free block after the last one. End block could be for example +500M so fdisk automatically finds the correct end block. Do the same for sde14, but note the start block again. sde14 end block should be the last block there is on the card.
After you've done that, do w to write and if it tells you to restart or something, unplug the phone, take out the battery and restart to pink screen again. Then try to use disk utility again or gparted (have not tested this) to reformat sde13 and sde14 to ext4 and vfat.
You should be safe until you don't mess with the primary partitions, especially the mmcblk0p2 and mmcblk0p3.

Thanks again for the reply, Blefish. I may have just fixed it. I'll know soon enough.
I did two things:
1) sudo fdisk /dev/sde12 followed by w
2) sudo fdisk /dev/sde followed by w
After that it enabled me to add the 13 and 14 partition. I used disk utility so I didn't have to worry about the blocks. Afterwards they mounted in ubuntu like they should.
UPDATE: Not quite fixed, but the rom installed without error. So I think the partition problem is fixed.
Now I just have a boot loop. I'll go back to ubuntu, clear the cache, and try installing from the internal sdcard
2nd UPDATE: Stock recovery gives and error about mounting the cache partition. However CWM mounts it fine. My partition problems may not be over.
3rd UPDATE: genokolar's "Custom you partition" file to return to stock file deletes my partition 13 and 14. Had 13 and 14 back working, used the file as per instructions, afterwards ubuntu drive utililty shows 13 and 14 as "free." So that is where part of my problem comes from.
4th UPDATE: Fixed the problem with stock recovery. Turns out froyo doesn't like ext4 partitions. Changed cache partition to ext3, no more error.

Here are some exerts from the CMW log when I tried to flash cyanongen. Can anyone tell me if any of these errors are problems, and if they are what they mean?
W:Unable to get recovery.fstab info for /datadata during fstab generation!
W:Unable to get recovery.fstab info for /sd-ext during fstab generation!
I:Checking for extendedcommand...
I:Skipping execution of extendedcommand, file not found...
failed to open /sys/class/android_usb/android0/state: No such file or directory
-- Installing: /sdcard/CM7-070512.zip
Finding update package...
I:Update location: /sdcard/CM7-070512.zip
Opening update package...
Installing update...
unmount of /system failed; no such volume
package_extract_file: no backup_initd.sh in package
set_perm: chown of /tmp/backup_initd.sh to 0 0 failed: No such file or directory
set_perm: chmod of /tmp/backup_initd.sh to 777 failed: No such file or directory
about to run program [/tmp/backup_initd.sh] with 2 args
run_program: execv failed: No such file or directory
run_program: child exited with status 1
Pass 5: Checking group summary information
/dev/block/mmcblk0p12: 11/56448 files (0.0% non-contiguous), 7142/225280 blocks
mount: failed to mount /dev/block/mmcblk0p12 at /system: Invalid argument
set_perm: chown of 0750 to 0 2000 failed: No such file or directory
set_perm: chmod of 0750 to 755 failed: No such file or directory
set_perm: chown of /system/etc/init.qcom.post_boot.sh to 0 2000 failed: No such file or directory
set_perm: chmod of /system/etc/init.qcom.post_boot.sh to 555 failed: No such file or directory
set_perm: chown of /system/xbin/apply_firewall to 0 0 failed: No such file or directory
set_perm: chmod of /system/xbin/apply_firewall to 6755 failed: No such file or directory
set_perm: chown of /system/xbin/apply_theme to 0 0 failed: No such file or directory
set_perm: chmod of /system/xbin/apply_theme to 6755 failed: No such file or directory
set_perm: chown of /system/xbin/dumplog to 0 0 failed: No such file or directory
set_perm: chmod of /system/xbin/dumplog to 6755 failed: No such file or directory
set_perm: chown of /system/xbin/mv2sd to 0 0 failed: No such file or directory
set_perm: chmod of /system/xbin/mv2sd to 6755 failed: No such file or directory
set_perm: chown of /system/xbin/ota to 0 0 failed: No such file or directory
set_perm: chmod of /system/xbin/ota to 6755 failed: No such file or directory
Updating BOOT Image...
about to run program [/tmp/backup_initd.sh] with 2 args
run_program: execv failed: No such file or directory
run_program: child exited with status 1
Installation complete!script result was [Installation complete!]
Install from sdcard complete.
failed to open /sys/class/android_usb/android0/state: No such file or directory

My phone is fixed. I have no idea how it became fixed, but it is fixed.
I placed b518 on the internal sd card, and installed it. Then bootloop. So I held both volume keys+power to try another rom. It installed again. Went to recovery, it did a factory reset. Bootloop. Went back to recovery to see if I could wipe the sd card. No option for it, so I did another factory reset and rebooted my phone. I left my phone bootlooping for a minute while I looked online for a Huawei service center, and then my phone booted. I gues it got scared and didn't want to go to a service center.
This been a great learning experience, although at times a major headaches. I want to thank blefish for all his help. Thanks to this, i've bee reading his blog and other stuff, and now will follow some of his other projects.
Now to downgrade back to 2.2!!!!
UPDATE: All official roms are working correctly (b136, b138, b518, b528), recovery (5.0.2.6) works. However I haven't been able to get a single custom rom to work. Tried a couple .32 MIUI and CM, but they all stick at the huawei logo. Did factory reset and dalvik wipe, get error can't mount /sd-ext during dalvik wipe, and still doesn't boot.
Maybe I need to try a newer verison of CWM? I tried the newer versions before, and I didn't like them. Buggy and often wouldn't find my sd card.

This thread must be made sticky because it consists of pure information about dealing with soft-bricks. Thanks a lot for your curiosity, you're my hero.

[Q] NST will not boot, lost partition table

The below post is actually a PM I sent to ros87, but it look like he hasn't been on the forums in a while, so I thought I'd ask the general populous. Besides, if I manage to get out of this one, then it might help someone else.
--------------------------
To make a long story short, I have a NST that will not boot from the internal memory. I can boot from SD card images no problem (noogie, cwm, n2T-Recovery). When I boot from noogie, I can see the internal storage.
How I managed to get here:
- tried to follow the "Backup/Restore N2E" instructions from Windows, so used MiniTool Partition Wizard to delete the NST partitions
- THEN I realized the backup I took a long time ago wasn't a full device backup, but individual partition backups:
Code:
07/14/2011 09:09 PM 79,675,392 nook_backup_BOOT.img
07/14/2011 09:41 PM 251,641,856 nook_backup_CACHE.img
07/14/2011 09:58 PM 840,941,568 nook_backup_DATA.img
07/14/2011 09:30 PM 301,973,504 nook_backup_DISK.img
07/14/2011 09:22 PM 199,229,440 nook_backup_FACTORY.img
07/14/2011 09:04 PM 251,641,856 nook_backup_NOOK.img
07/14/2011 09:19 PM 16,777,216 nook_backup_ROM.img
I wasn't having any luck with Windows-based tools, so I switched to Linux. I've attempted to rebuild the partitions and copy over the data from my backups using dd:
Code:
dd if=/home/kenny/host/Nook\ Backup/nook_backup_BOOT.img of=/dev/sdb1 bs=1M
dd if=/home/kenny/host/Nook\ Backup/nook_backup_ROM.img of=/dev/sdb2 bs=1M
dd if=/home/kenny/host/Nook\ Backup/nook_backup_FACTORY.img of=/dev/sdb3 bs=1M
dd if=/home/kenny/host/Nook\ Backup/nook_backup_DISK.img of=/dev/sdb5 bs=1M
dd if=/home/kenny/host/Nook\ Backup/nook_backup_NOOK.img of=/dev/sdb6 bs=1M
dd if=/home/kenny/host/Nook\ Backup/nook_backup_CACHE.img of=/dev/sdb7 bs=1M
dd if=/home/kenny/host/Nook\ Backup/nook_backup_DATA.img of=/dev/sdb8 bs=1M
The commands seemed to work and I do see the right kind of data in the partitions, but it still won't boot.
Here's a dump of the current state of things:
Code:
fdisk -l /dev/sdb
Disk /dev/sdb: 1958 MB, 1958739968 bytes
128 heads, 32 sectors/track, 934 cylinders
Units = cylinders of 4096 * 512 = 2097152 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000001
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 38 77808 c W95 FAT32 (LBA)
/dev/sdb2 39 46 16384 c W95 FAT32 (LBA)
/dev/sdb3 47 141 194560 83 Linux
/dev/sdb4 142 934 1624064 5 Extended
/dev/sdb5 142 285 294896 83 Linux
/dev/sdb6 286 405 245744 c W95 FAT32 (LBA)
/dev/sdb7 406 525 245744 83 Linux
/dev/sdb8 526 926 821232 83 Linux
--------------------------
df -h
/dev/sdb5 279M 183M 94M 67% /media/boot
/dev/sdb7 233M 6.2M 224M 3% /media/cache
/dev/sdb2 16M 119K 16M 1% /media/rom
/dev/sdb3 184M 106M 77M 58% /media/factory
/dev/sdb8 790M 20K 782M 1% /media/boot_
/dev/sdb6 237M 104M 133M 44% /media/NOOK
/dev/sdb1 75M 58M 18M 78% /media/boot__
I'm not entirely sure I got the partitions created in the format or order the nook wants. Luckily, since I do have the contents of the partitions, I do feel like I can get out of this mess, but just haven't managed to find the right sequence yet.
What I'd love to try is using a good, full backup that someone else has made, and then use my individual partition backups to rewrite the sections that are unique to my nook. Unfortunately, the torrent containing the one full backup that someone posted is long dead.
So, If there's anything anyone can think of that will help me revive this thing, I'd be ever so grateful. If you need more information, I'll get it.
Thanks!!!

"What I'd love to try is using a good, full backup that someone else has
made, and then use my individual partition backups to rewrite the
sections that are unique to my nook. Unfortunately, the torrent containing
the one full backup that someone posted is long dead."
You can boot into CWR, and you can probably pull a copy of the factory.zip file from one of your restored partitions.
But I think that where you are is a fixable point at this time - somehow (perhaps because you restored partition by partition and thus weren't able to get a correct set of names tied to them) the names are wrong on some pretty important partitions - system, data and boot!
The partitions at a very fast glance look OK to me in terms of size, number and order.
This, though:
/dev/sdb5 279M 183M 94M 67% /media/boot
/dev/sdb8 790M 20K 782M 1% /media/boot_
/dev/sdb1 75M 58M 18M 78% /media/boot__
/sdb5 should be /system;
/sdb8 should be /data (I seem to remember that Linux calls it 'userdata' when the disk is mounted)
/sdb1 should be boot -- no terminal underscores.
You can rename the partitions using parted in Linux. I would start there - boot noogie, use linux parted to address the problem with partition 1. Try renaming 5 as system and 8 as userdata (I don't have the output to hand to show you exactly what this will look like in parted)
the syntax at the CLI is
(parted) name 1 boot
(parted) quit
for partition 1 to get the name boot
(but also use the parted print command to look to see what the partitions are being called by the disk. There may be others that need tuning, but it looks as if the df command actually did find out what the disk was calling the partitions, which is helpful.)
gparted may work also, and it's a little less intimidating to use if there's a rename partition command in it.
If you can get it to boot even enough to fail, your restore image should be visible to the device and it will eventually see that it's failed enough times to force a reset.

Thanks for the detailed reply!
Since I wrote the above message, I did play with the partitions a little more to get the order to better match what I found in the Nook Touch Partition Hacking thread. Here's how it looks in gParted, after I did the labeling (parted wouldn't name a FAT32 partition):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Still no luck trying to boot after the renaming.
Then I tried using CWM to flash the factory.zip I was able to extract from my backup. It flashed successfully, but still no boot.
I still question my partition table a bit simply because I haven't been able to find a really good reference as to what the table on a stock Nook should look like.

Kaishio said:
I still question my partition table a bit simply because I haven't been able to find a really good reference as to what the table on a stock Nook should look like.
Click to expand...
Click to collapse
That's what I see:
fdisk -l /dev/block/mmcblk0
Code:
Disk /dev/block/mmcblk0: 1958 MB, 1958739968 bytes
128 heads, 32 sectors/track, 934 cylinders
Units = cylinders of 4096 * 512 = 2097152 bytes
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 * 1 38 77808 c Win95 FAT32 (LBA)
/dev/block/mmcblk0p2 39 46 16384 c Win95 FAT32 (LBA)
/dev/block/mmcblk0p3 47 141 194560 83 Linux
/dev/block/mmcblk0p4 142 926 1607680 5 Extended
/dev/block/mmcblk0p5 142 285 294896 83 Linux
/dev/block/mmcblk0p6 286 405 245744 c Win95 FAT32 (LBA)
/dev/block/mmcblk0p7 406 525 245744 83 Linux
/dev/block/mmcblk0p8 526 926 821232 83 Linux
mount
Code:
rootfs / rootfs ro 0 0
tmpfs /dev tmpfs rw,mode=755 0 0
devpts /dev/pts devpts rw,mode=600 0 0
proc /proc proc rw 0 0
sysfs /sys sysfs rw 0 0
tmpfs /sqlite_stmt_journals tmpfs rw,size=4096k 0 0
/dev/block/mmcblk0p2 /rom vfat rw,sync,noatime,nodiratime,uid=1000,gid=1000,fmask=0117,dmask=0007,allow_utime=0020,codepage=cp437,iocharset=iso8859-1,errors=remount-ro 0 0
/dev/block/mmcblk0p5 /system ext2 ro,errors=continue 0 0
/dev/block/mmcblk0p8 /data ext3 rw,nosuid,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0
/dev/block/mmcblk0p7 /cache ext3 rw,nosuid,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0

Really appreciate the responses.
...but I'm still stuck. I made my partitions match exactly what ApokrifX posted, restored from my backups, but no boot. So strange. I'll keep messing with it though.
Maybe I'll have to ninja into barnes and noble and take a full device backup of one of the display units.

Don’t really know what to suggest...
Do you see anything on the screen when it fails to boot?
Were you able to find someone else full backup?
Can you boot noggie, take full backup and try to understand what’s messed up in it by comparing?

I have a theory that all the B&N Nook products have some sort of unbrick mode built in. I have not had a chance to try with a NST but it works fine for my Nook tablet.
1. Create partition table and format partitions see how I did this here http://forum.xda-developers.com/showthread.php?t=1225196
2. set up the first partition with MLO uboot uImage and recovery
3. Get hold of a update file from B&N Site and strip the leading signapk bits and put it on a blank sdcard after renaming it as gossamer_update.zip
4 Start up the nook it should boot from internal emmc see the presence of the special update.zip on sdcard and upgrade / downgrade reinstall etc
just look at some of the posts in the B&N Tablet threads and all this stuff works on that, grepping the source for uboot on the NST gives the gossamer name

meghd00t said:
I have a theory that all the B&N Nook products have some sort of unbrick mode built in. I have not had a chance to try with a NST but it works fine for my Nook tablet.
1. Create partition table and format partitions see how I did this here http://forum.xda-developers.com/showthread.php?t=1225196
2. set up the first partition with MLO uboot uImage and recovery
3. Get hold of a update file from B&N Site and strip the leading signapk bits and put it on a blank sdcard after renaming it as gossamer_update.zip
4 Start up the nook it should boot from internal emmc see the presence of the special update.zip on sdcard and upgrade / downgrade reinstall etc
just look at some of the posts in the B&N Tablet threads and all this stuff works on that, grepping the source for uboot on the NST gives the gossamer name
Click to expand...
Click to collapse
Cool.
OR he can actually use your approach and his backup of all partition to create whole nook image as well! :good:

Thanks m. I only had a few minutes today to mess with it, and while I didn't have any success, it wasn't the best attempt. I'll do more when I have more time.
That being said, to answer ApokrifX's earlier question, I don't see anything change on the screen for a failed boot. If it said Rooted Forever before, that's what stays. If it was CWM's "rebooting" message, that's what stays.
At this point, I'm wondering, rather than trying for a full restore, if I should just focus on getting any sort of boot from emmc. So far, I've had not been able to get any response with a SD card removed. What's the simplest way to show/test any sort of boot from internal memory?

Kaishio said:
At this point, I'm wondering, rather than trying for a full restore, if I should just focus on getting any sort of boot from emmc. So far, I've had not been able to get any response with a SD card removed. What's the simplest way to show/test any sort of boot from internal memory?
Click to expand...
Click to collapse
I wish I can answer that.
Might be coping noogie.img content to first nook partition?
I would PM to mali100 to get clarification first.

ApokrifX said:
Might be coping noogie.img content to first nook partition?
Click to expand...
Click to collapse
That should work, but the boot partition has to start on the correct sector.

mali100 said:
That should work, but the boot partition has to start on the correct sector.
Click to expand...
Click to collapse
Mali,
Do you mean alignment, or something else?
I thought, it is same way everywhere:
“Disk boot sector” (Partition loader) finds first/last active partition, loads its first sector and jumps to it.
“Active partition boot sector” finds boot file by name or have its offset, loads it (partially) and jumps to it.
No idea how it works with noogie, but gotta be something similar?
Another Q:
In Kaishio case, could it be that partitions have correct sizes, but wrong offsets, thus booting process fails?

As I understand it the restrictions are
1. Geometry 128Heads * 32Sectors per track
2. 1st partition has to be type Win95 LBA
3. 1st partition has to be bootable
4. MLO has to be uppercase and the first file on the file system
I had to fiddle a long time with sfdisk to get these rules right.

Kaishio said:
Code:
fdisk -l /dev/sdb
Disk /dev/sdb: 1958 MB, 1958739968 bytes
128 heads, 32 sectors/track, 934 cylinders
Units = cylinders of 4096 * 512 = 2097152 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000001
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 38 77808 c W95 FAT32 (LBA)
/dev/sdb2 39 46 16384 c W95 FAT32 (LBA)
Click to expand...
Click to collapse
meghd00t said:
As I understand it the restrictions are
1. Geometry 128Heads * 32Sectors per track
2. 1st partition has to be type Win95 LBA
3. 1st partition has to be bootable
4. MLO has to be uppercase and the first file on the file system
I had to fiddle a long time with sfdisk to get these rules right.
Click to expand...
Click to collapse
Looks like he had satisfied first 3 conditions.
IMO, if "MLO has to be uppercase", then bootloader is searching for it by name, so it doesn’t have to be "the first file on the file system"
---------- Post added at 04:36 PM ---------- Previous post was at 04:25 PM ----------
Funny: http://overoinfo.blogspot.com/2010/03/creating-bootable-microsd-card.html
It is very important that these three files have precisely these names and are loaded into the boot partition in a very specific order. The Overo boot loader does not use the names per-se but instead loads the FIRST installed file on the boot partition (MLO) which does look for specific name 'u-boot.bin' when it is time to load the boot loader. The boot loader also looks for the specific name uImage to load the Linux kernel.
Click to expand...
Click to collapse
I.e. only u-boot.bin and uImage names are important.
MLO has to be FIRST installed file on the boot partition.
It can have any name.

take a NSTG back to stock

Hi,
I succesfullly rooted my Nook glowlight, but when I tried to go back to stock with my nook backup I found the backup was not ok (just 77MB) and now I have a bricked NSTG that won't get past the "Install Failed" screen.
I've tried almost every method I could find in the forums, but none worked for me.
Is there anything else beside n2T and Alpha-Format I could try to revive my device?
TIA

I think the most careful way to proceed here is to get a shell going and inspect the damage.
If you were lucky you just wiped out the first partition and the partition tables.
Reinstating the partition tables might make undamaged partitions visible.
It's important to preserve the device dependent info on the /rom partition.
If you copy over ClockworkRecovery onto an SD card you should be able to boot that.
Without selecting anything on the menus you should be able to get ADB working.
With an ADB shell you can run fdisk -l /dev/block/mmcblk0
As soon as you can get access to /rom I'd suggest that you back that up.
I'm sure somebody has other ways to get shell access.

Renate NST said:
I think the most careful way to proceed here is to get a shell going and inspect the damage.
If you were lucky you just wiped out the first partition and the partition tables.
Reinstating the partition tables might make undamaged partitions visible.
It's important to preserve the device dependent info on the /rom partition.
If you copy over ClockworkRecovery onto an SD card you should be able to boot that.
Without selecting anything on the menus you should be able to get ADB working.
With an ADB shell you can run fdisk -l /dev/block/mmcblk0
As soon as you can get access to /rom I'd suggest that you back that up.
I'm sure somebody has other ways to get shell access.
Click to expand...
Click to collapse
thanks for that I'll give it a try...
Sadly, I'm on a W7 box (not mine) and all I can see in the device manager is a nook with a yellow sign in it
ADB devices returns a blank list....
I tried updating the drivers for the nook: first uninstalled anything nooklike with usbdeview, and then pointed W7 to a folder where I had downloaded usbdrivers from this thread http://forum.xda-developers.com/showthread.php?t=1354487 but W7 keeps telling there are no drivers for nook in that folder.
If I boot without SD then the nook is recognized and USB drivers install fine. It's booting with CWM that the device is not recognized.
Stuck

There are drivers and drivers.
As a composite USB device the Nook uses both the stock Windows Mass Storage driver and the Google ADB driver.
See: http://forum.xda-developers.com/wiki/BN_Nook_Simple_Touch/Installing_ADB

Renate NST said:
There are drivers and drivers.
As a composite USB device the Nook uses both the stock Windows Mass Storage driver and the Google ADB driver.
See: http://forum.xda-developers.com/wiki/BN_Nook_Simple_Touch/Installing_ADB
Click to expand...
Click to collapse
It worked:
D:\nook_root\adbshell>adb devices
List of devices attached
11223344556677 recovery
D:\nook_root\adbshell>adb shell
~ # fdisk -l /dev/block/mmcblk0
fdisk -l /dev/block/mmcblk0
Disk /dev/block/mmcblk0: 1958 MB, 1958739968 bytes
4 heads, 16 sectors/track, 59776 cylinders
Units = cylinders of 64 * 512 = 32768 bytes
Device Boot Start End Blocks Id System
~ #
completely noob with the nook, can't seem to find /rom and Win32DiskImager does not find a device to read from to perform said backup

The best bet would be to check with somebody with a Glow to see if the partitioning is the same as the Touch.
They could have even changed the exact size of partitions over time for the same model.
In any case, here are my partitions. You might try partitioning and not formatting and see if all the pieces fit properly.
Code:
Disk /dev/block/mmcblk0: 1958 MB, 1958739968 bytes
128 heads, 32 sectors/track, 934 cylinders
Units = cylinders of 4096 * 512 = 2097152 bytes
Partition Format Id Start End Size (bytes) Mount
--------- ------ -- ----- --- ------------- --------
Total 0 933 1,958,739,968
mmcblk0p1 vfat 0c 1 38 79,691,776 /boot
mmcblk0p2 vfat 0c 39 46 16,777,216 /rom
mmcblk0p3 ext2 83 47 141 199,229,440 /factory
mmcblk0p4 05 142 926 1,646,264,320
mmcblk0p5 ext2 83 142 285 301,989,888 /system
mmcblk0p6 vfat 0c 286 405 251,658,240 /media
mmcblk0p7 ext3 83 406 525 251,658,240 /cache
mmcblk0p8 ext3 83 526 926 840,957,952 /data
Unused 927 933 14,680,064

Renate NST said:
The best bet would be to check with somebody with a Glow to see if the partitioning is the same as the Touch.
They could have even changed the exact size of partitions over time for the same model.
In any case, here are my partitions. You might try partitioning and not formatting and see if all the pieces fit properly.
Code:
Disk /dev/block/mmcblk0: 1958 MB, 1958739968 bytes
128 heads, 32 sectors/track, 934 cylinders
Units = cylinders of 4096 * 512 = 2097152 bytes
Partition Format Id Start End Size (bytes) Mount
--------- ------ -- ----- --- ------------- --------
Total 0 933 1,958,739,968
mmcblk0p1 vfat 0c 1 38 79,691,776 /boot
mmcblk0p2 vfat 0c 39 46 16,777,216 /rom
mmcblk0p3 ext2 83 47 141 199,229,440 /factory
mmcblk0p4 05 142 926 1,646,264,320
mmcblk0p5 ext2 83 142 285 301,989,888 /system
mmcblk0p6 vfat 0c 286 405 251,658,240 /media
mmcblk0p7 ext3 83 406 525 251,658,240 /cache
mmcblk0p8 ext3 83 526 926 840,957,952 /data
Unused 927 933 14,680,064
Click to expand...
Click to collapse
mmmm, a bit risky isn't it ?
I think I'll read the rest of the internets before proceeding I need to understand this.....
thanks again

srgarfi said:
mmmm, a bit risky isn't it ?
Click to expand...
Click to collapse
Well, you don't have anything at all in your partition table, not even the correct CHS.
If you tried this configuration and you can't mount the partition, then no harm is done.
It will only mount if the partition formatting makes sense.

Renate NST said:
If you tried this configuration and you can't mount the partition, then no harm is done.
It will only mount if the partition formatting makes sense.
Click to expand...
Click to collapse
Oh, ah, that changes everything! It's worth a try.
I need to find a dummy guide to perform this operations, any clues?
Edit: Found this, looks like a start http://forum.xda-developers.com/showthread.php?t=1279091
thanks again

booted in gparted live and took a peek at the Nook. This is what I found (sorry I don't know yet how to post images):
Device information
Model: B&N Ebook Disk
Size: 182 GiB
Path: /dev/sdb
Partition table: msdos
Heads: 255
Sectors/track: 63
Cylinders: 238
Total sectors: 3825664
Sector size: 512
Physical characteristics being so different I'm affraid trying to convert heads/cylinders from Renate's Touch to my Glo schema would be useless.
Could someone with a NSTG please share partition information?
Thank you all,

srgarfi said:
Physical characteristics being so different...
Click to expand...
Click to collapse
Well, they are not real physical differences.
You can juggle heads and sectors/track as long as the size of a cylinder stays the same.
It may be that the Glow has gone to a bigger cylinder, but it's suspicious that it's not a power of two.

Renate NST said:
You can juggle heads and sectors/track as long as the size of a cylinder stays the same.
Click to expand...
Click to collapse
Not good at math, I can't get an exact match

Here is a script that will partition your Nook internal SD card like the listing above.
You can either copy this to the SD card, chmod 777 it and run it
or just copy and paste it to the Windows command line window running ADB.
Then you can try some mounts and see what you've got.
(nookpart.sh is zipped.)

was about to try the script (thanks again!) but nook is stuck at "rooted forever" screen and nothing I do awakes it: power on, power on 30 sec, power on and n, plug it to pc, and every combination. Took off the sd and tried combinations again, nothing. I've searched a bit and all other cases resumed to reboot by pressing long power. Not this one....no hard reset available? Every piece of equipment must have a big red switch =)
Should I stop messing around and buy another one? (not in the states anymore, it will take like 40+ days to deliver here...)
EDIT: false alarm, battery was too low to power on. Where did the full charge go? I dunno....30 more minutes before I can try

Renate NST said:
Here is a script that will partition your Nook internal SD card like the listing above.
You can either copy this to the SD card, chmod 777 it and run it
or just copy and paste it to the Windows command line window running ADB.
Then you can try some mounts and see what you've got.
(nookpart.sh is zipped.)
Click to expand...
Click to collapse
Executed the script:
Code:
D:\nook_root\adbshell>adb shell sh /sdcard/nookpart.sh
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (1-934, default 1): Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-934, default 934):
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (39-934, default 39): Using default value
39
Last cylinder or +size or +sizeM or +sizeK (39-934, default 934):
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (47-934, default 47): Using default value
47
Last cylinder or +size or +sizeM or +sizeK (47-934, default 934):
Command (m for help): Command action
e extended
p primary partition (1-4)
Selected partition 4
First cylinder (142-934, default 142): Using default value 142
Last cylinder or +size or +sizeM or +sizeK (142-934, default 934):
Command (m for help): First cylinder (142-926, default 142): First cylinder (142
-926, default 142): Using default value 142
Last cylinder or +size or +sizeM or +sizeK (142-926, default 926):
Command (m for help): First cylinder (286-926, default 286): First cylinder (286
-926, default 286): Using default value 286
Last cylinder or +size or +sizeM or +sizeK (286-926, default 926):
Command (m for help): First cylinder (406-926, default 406): First cylinder (406
-926, default 406): Using default value 406
Last cylinder or +size or +sizeM or +sizeK (406-926, default 926):
Command (m for help): First cylinder (526-926, default 526): First cylinder (526
-926, default 526): Using default value 526
Last cylinder or +size or +sizeM or +sizeK (526-926, default 926):
Command (m for help): Partition number (1-8): Hex code (type L to list codes): C
hanged system type of partition 1 to c (Win95 FAT32 (LBA))
Command (m for help): Partition number (1-8): Hex code (type L to list codes): C
hanged system type of partition 2 to c (Win95 FAT32 (LBA))
Command (m for help): Partition number (1-8): Hex code (type L to list codes): C
hanged system type of partition 6 to c (Win95 FAT32 (LBA))
Command (m for help): Partition number (1-8):
Command (m for help):
Disk /dev/block/mmcblk0: 1958 MB, 1958739968 bytes
128 heads, 32 sectors/track, 934 cylinders
Units = cylinders of 4096 * 512 = 2097152 bytes
Device Boot Start End Blocks Id System
/dev/block/mmcblk0p1 * 1 38 77808 c Win95 FAT32 (LB
A)
/dev/block/mmcblk0p2 39 46 16384 c Win95 FAT32 (LB
A)
/dev/block/mmcblk0p3 47 141 194560 83 Linux
/dev/block/mmcblk0p4 142 926 1607680 5 Extended
/dev/block/mmcblk0p5 142 285 294896 83 Linux
/dev/block/mmcblk0p6 286 405 245744 c Win95 FAT32 (LB
A)
/dev/block/mmcblk0p7 406 525 245744 83 Linux
/dev/block/mmcblk0p8 526 926 821232 83 Linux
Command (m for help): The partition table has been altered.
Calling ioctl() to re-read partition table
D:\nook_root\adbshell>
From CWM tried to mount /boot and failed. Took off the SD, booted nook (fingers crossed) and it displayed the "install failed" screen.
Nice try, thanks for the patience :good:

No, that's what I expected.
The partitioning worked fine
You had already bashed the boot partition.
Now try:
Code:
mkdir /rom
mount -t vfat /dev/block/mmcblk0p2 /rom
ls -l /rom

Looks like there was already a /rom
Code:
D:\nook_root\adbshell>adb shell
~ # mkdir /rom
mkdir /rom
mkdir: can't create directory '/rom': File exists
~ # mount -t vfat /dev/block/mmcblk0p2 /rom
mount -t vfat /dev/block/mmcblk0p2 /rom
mount: mounting /dev/block/mmcblk0p2 on /rom failed: Device or resource busy
~ # ls -l /rom
ls -l /rom
-rwxrwxrwx 1 root root 1088 Jan 1 02:30 bcb
drwxrwxrwx 2 root root 2048 Jan 1 02:30 devconf
~ #

Hmm, I thought of that at the last moment.
Code:
mkdir /stuff
mount -t vfat /dev/block/mmcblk0p2 /stuff
ls -l /stuff

Renate NST said:
Hmm, I thought of that at the last moment.
Code:
mkdir /stuff
mount -t vfat /dev/block/mmcblk0p2 /stuff
ls -l /stuff
Click to expand...
Click to collapse
yes, works, but I don't get it?
Code:
~ # mkdir /stuff
mkdir /stuff
~ # mount -t vfat /dev/block/mmcblk0p2 /stuff
mount -t vfat /dev/block/mmcblk0p2 /stuff
~ # ls -l /stuff
ls -l /stuff
-rwxrwxrwx 1 root root 1088 Jan 1 02:30 bcb
drwxrwxrwx 2 root root 2048 Jan 1 02:30 devconf
~ #
in the meantime I booted noogie and did a backup of the semibricked nook just in case.... =)
Now I'll write CWM to the SD and boot again

That means that the partitioning is correct and that your /rom is intact.
Make a good backup of your personalized stuff:
Code:
adb pull /stuff
Now you have to fix up the boot partition.
I'd probably try to install the factory.zip
Code:
mkdir /fact
mount -t ext2 /dev/block/mmcblk0p3 /fact
ls -l /fact
Code:
adb pull /fact/factory.zip
adb pull /fact/rombackup.zip
Then copy factory.zip to the external SD card and do a CWR update with that.

No way to unlock device. Is it bricked?

My Nexus 7 wifi tablet was working flawlessly for a few months since buying.
It was rooted, unlocked with stock android 4.2.1 and Team Win Recovery 2.3.2.1
Yesterday morning after charging all the night I saw that it was completely turned off. It didn't bother me, because it happened a couple of times before.
But this time, after I'd switched it on it hung on google color logo.
I waited half an hour but to no avail.
So at first I booted to recovery and wiped cache and the like. But the problem remained. Factory reset didn't help either.
So as a last resort I formated everything (including system).
Then I saw surprisingly in fastboot mode that lock state is: LOCKED.
I've tried to unlock it but it ended with an error:
C:\Users\Warp\AppData\Local\Android\android-sdk\platform-tools>fastboot oem unlock
...
(bootloader) erasing userdata...
(bootloader) erasing userdata done
(bootloader) erasing cache...
FAILED (remote: (Unknown error code))
finished. total time: 7.241s
After I'd pressed "yes" to the question "unlock bootloader" on tablet it was displaying text "Neither USP nor CAC patition found" in a loop.
Because there is still TWR installed and I can't wipe it out i think I've lost the guarantee.
I can see my device in fastboot mode:
C:\Users\Warp\AppData\Local\Android\android-sdk\platform-tools>fastboot getvar all
(bootloader) version-bootloader: 4.13
(bootloader) version-baseband: N/A
(bootloader) version-hardware: ER3
(bootloader) version-cdma: N/A
(bootloader) variant: grouper
(bootloader) serialno: XXXXXXXXXXXXXXXXXXXXXX
(bootloader) product: grouper
(bootloader) secure: yes
(bootloader) unlocked: no
(bootloader) uart-on: no
(bootloader) partition-size:bootloader: 0x0000000000600000
(bootloader) partition-type:bootloader: emmc
(bootloader) partition-size:recovery: 0x0000000000c00000
(bootloader) partition-type:recovery: emmc
(bootloader) partition-size:boot: 0x0000000000800000
(bootloader) partition-type:boot: emmc
(bootloader) partition-size:system: 0x0000000028a00000
(bootloader) partition-type:system: ext4
(bootloader) partition-size:cache: 0x000000001bb00000
(bootloader) partition-type:cache: ext4
(bootloader) partition-size:userdata: 0x0000000364700000
(bootloader) partition-type:userdata: ext4
all:
finished. total time: 0.193s
Is there anything left I can try?

AW: No way to unlock device. Is it bricked?
Have you tried reflashing stock rom? Maybe this rewrites recovery, too
Sent from my SK17i running Android 4.1.2

mihahn said:
Have you tried reflashing stock rom? Maybe this rewrites recovery, too
Click to expand...
Click to collapse
Yes, but it can't be done because the device is locked.

Before you do anything drastic, realize that you still have (in TWRP) a privileged execution environment (a root shell).
That means at a minimum you have a root-privileged shell available and some tools for fooling with partitions known to the TWRP kernel.
By drastic, I mean specifically: don't overflash the recovery partition at the command line from the root shell using /sbin/flash_image. Keep "root" until you are sure that nothing else can be done.
Back in a couple minutes - booting my N7 into TWRP right now to have a look at some things.
[ Edit ] From your post I see you have fastboot drivers set up - can you connect to TWRP via ADB?

Thank you for your reply.
Yes, I can see my device using: adb devices
adb shell also works.
[Edit] One more odd thing, when TWRP starts it asks me to enter my password. I think it's related to data encrypted partition but I've never done it for sure.

Well, I have a couple of hypotheses.
I guess I should ask one more question - is it correct that in TWRP you see none of your backups in /sdcard (TWRP mounts /sdcard on when it starts up) ?
If you have anything left on the SD card you want saved, get it backed up to your PC with "adb pull" before proceeding any further. (All suggestions below assume you have nothing left to save anywhere in /data.)
Also, I note that my N7 discharges slowly when plugged into my computer but sitting at the TWRP screen - so get your nexus fully charged before going any further.
The fact that you can boot TWRP means that the bootloader can find your recovery image, so at a minimum that means the bootloader can still understand some of the partitioning information it has available.
It is possible that the initial problem you had was something as simple as a corruption of a ext4 file system involving /cache, /system, or /data - as they need to be mounted after the early boot (ramdisk) initialization has more or less finished up. If they can not be mounted, the late boot processes never occur. Looking at your subsequent problems with unlocking the bootloader indicate a problem with the /cache partition - maybe?
[ The re-locking of the bootloader is odd, though. It suggests something got erased or mangled in a partition of the flash RAM that normally does not get mounted or touched by any of the usual kernel boots (whether we are talking about a recovery boot or any other android kernel boot). That means something other than /system, /cache, or /data - probably misc1, misc2, mfg, or possibly somewhere else (like slack space at the ends of either the boot or recovery partitions, or even in hard-coded location. ]
What happens if you try to rebuild the ext4 filesystems on /cache, /system, and /data?
[ note the partitions below are for the grouper N7 device; do a "adb shell cat /etc/fstab" to see if there are differences if you are on tilapia (3G version of the Nexus 7) ]
C:\foo> adb shell
# umount /data
# umount /cache
# umount /sdcard
# /sbin/mke2fs -t ext4 -m 0 /dev/block/mmcblk0p4
# /sbin/mke2fs -t ext4 -m 0 /dev/block/mmcblk0p3
# /sbin/mke2fs -t ext4 -m 0 /dev/block/mmcblk0p9
Does this succeed or fail? If it fails, what about first trying
# /sbin/erase_image /dev/block/mmcblk0p??? ( substitute correct # for ???)
prior to the mke2fs operation?
If you can get them to succeed, you might try restoring a backup (adb push to your "SD card"), and then doing a restore from TWRP and see if you can get it to boot.
You may also want to get your misc1 and misc2 partitions backed up - they contain the partitioning information (and usually the android "boot communication block), and they are generally identical (down to the last byte):
C:\foo> adb shell
# mount /sdcard (if this fails then you can't do this obviously)
# dd if=/dev/block/mmcblk0p5 of=/sdcard/part5.img bs=4096
# dd if=/dev/block/mmcblk0p8 of=/sdcard/part8.img bs=4096
# exit
C:\foo> adb pull /sdcard/part5.img
C:\foo> adb pull /sdcard/part8.img
If one of misc1 or misc2 got corrupted - and that is what is confusing the bootloader - it should be possible to flash the bad one with the good spare - but let's leave that alone until we see if /cache, /data, and /system can be re-initialized.
I'll come back to this thread in 8 hours or so - time for bed for me.

bftb0 said:
Well, I have a couple of hypotheses.
is it correct that in TWRP you see none of your backups in /sdcard (TWRP mounts /sdcard on when it starts up) ?
Click to expand...
Click to collapse
Yes it mounts it and it is empty (besides TWRP directory). I don't have backup either but it is no problem for me. I just want to start with stock Android 4.2.1 or if it's not possible - wipe out TWRP and send nexus for repairing.
bftb0 said:
What happens if you try to rebuild the ext4 filesystems on /cache, /system, and /data?
Does this succeed or fail?
Click to expand...
Click to collapse
Everything went smoothly, no errors here.
bftb0 said:
If you can get them to succeed, you might try restoring a backup (adb push to your "SD card"), and then doing a restore from TWRP and see if you can get it to boot.
Click to expand...
Click to collapse
I was trying to install a few roms this way, but the flashing never ends. On nexus I can see all the time: Flashing file 1 of 1 /sdcard/aokp_grouper_jb-mr1_build-1.zip
As I saw in recovery.log the problem is at the moment when filesystem is created:
C:\Users\Warp\AppData\Local\Android\android-sdk\platform-tools>adb shell cat /tmp/recovery.log
[cut]
I:Set page: 'main2'
I:Set page: 'install'
I:Set page: 'flash_confirm'
I:Set page: 'flash_zip'
I:Set page: 'flash_zip'
Installing '/sdcard/aokp_grouper_jb-mr1_build-1.zip'...
Checking for MD5 file...
Skipping MD5 check: no MD5 file found.
Creating filesystem with parameters:
Size: 681574400
Block size: 4096
Blocks per group: 32768
Inodes per group: 6944
Inode size: 256
Journal blocks: 2600
Label:
Blocks: 166400
Block groups: 6
Reserved block group size: 47
Created filesystem with 11/41664 inodes and 5415/166400 blocks
and it stops here.
bftb0 said:
You may also want to get your misc1 and misc2 partitions backed up - they contain the partitioning information (and usually the android "boot communication block), and they are generally identical (down to the last byte):
Click to expand...
Click to collapse
Ok, done. I've checked they are identical.
bftb0 said:
I'll come back to this thread in 8 hours or so - time for bed for me.
Click to expand...
Click to collapse
Great I'm waiting impatiently.
Regards

warpek said:
...I don't have backup either...
Click to expand...
Click to collapse
Arrgh - you never made any backups?. I was hoping you had a TWRP backup - they are just tar files, so you can manually untar them into mounted partitions at the command line... and that way see if any errors occur on an individual partition you are working with. But I'll come back to this in a little bit.
warpek said:
Everything went smoothly, no errors here.
Click to expand...
Click to collapse
OK, got it.
warpek said:
As I saw in recovery.log the problem is at the moment when filesystem is created:
[cut]
Creating filesystem with parameters:
Size: 681574400
...
Created filesystem with 11/41664 inodes and 5415/166400 blocks
and it stops here.
Click to expand...
Click to collapse
Well, 650 MB (=681574400 bytes) is the /system partition, and the "Created filesystem" message probably indicates success with a mke2fs operation. But mke2fs does not wipe all the blocks, so it is still possible that the *restore to /system* operation is hanging on a media failure.
warpek said:
Ok, done. I've checked they are identical.
Click to expand...
Click to collapse
Just out of curiosity, do you get a md5sum of 3039dc3a07a56d0392d48787e4a202a1 for your part5.img and part8.img files? In principle, yours should not be identical to mine - especially if there is something unusual in the BCB (Boot Control Block), but there is a chance they are the same as these partitions seem to contain multiple backups of partitioning information. (My N7 appears to have been made in December)
OK, lets try something innocuous - raw read tests on all of your partitions. Let's see if you have a bunch of bad pages in one partition.
With TWRP running
C:\foo> adb shell
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0boot0
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0boot1
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p1
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p2
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p3
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p4
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p5
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p6
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p7
# dd of=/dev/null bs=4096 if=/dev/block/mmcblk0p8
These should all go through pretty quickly - I omitted the /data partition (p9) because it is huge. The next largest (system/p3) should take about 20 seconds for a successful raw read. If you get a read failure, repeat the command on the offending partition with the "conv=noerror" option, as in
dd of=/dev/null bs=4096 conv=noerror if=/dev/block/mmcblk0p8
Basically I'm just looking for you to narrow down the search to a problem partition. The next step is to try to manually unpack files into /system, /cache, and /data to see if there is a flash media problem in one of those partitions. Unfortunately, this is where TWRP backup files would have been useful: ROM files are not useful for this, and the google factory images e.g. nakasi-jop40d-factory-6ac58a1a.tgz contain image files which are not archives - they are "sparse ext4 images".
Even though you observed no failures with the mke2fs operations, you might want to also try to repeat that process (only for p3, p4, and p9 !) , but this time using the partition erase command first.
# /sbin/erase_image /dev/block/mmcblk0pN
prior to the mke2fs operation.
OK, standing by.

bftb0 said:
Arrgh - you never made any backups?
Click to expand...
Click to collapse
I always do, but I though that because there are no important files for me on the nexus and everything else can be downloaded (system image, twrp) there is no need. Obviously I was mistaken.
bftb0 said:
Just out of curiosity, do you get a md5sum of 3039dc3a07a56d0392d48787e4a202a1 for your part5.img and part8.img files?
Click to expand...
Click to collapse
I used md5sum to co compare those files, here is mine:
part5.img 59071590099d21dd439896592338bf95
part8.img 59071590099d21dd439896592338bf95
bftb0 said:
OK, lets try something innocuous - raw read tests on all of your partitions. Let's see if you have a bunch of bad pages in one partition.
Click to expand...
Click to collapse
Everything looks ok here. No errors and no long time reads.
bftb0 said:
Basically I'm just looking for you to narrow down the search to a problem partition. The next step is to try to manually unpack files into /system, /cache, and /data to see if there is a flash media problem in one of those partitions. Unfortunately, this is where TWRP backup files would have been useful:
Click to expand...
Click to collapse
Is there anything I can I do then?
bftb0 said:
Even though you observed no failures with the mke2fs operations, you might want to also try to repeat that process (only for p3, p4, and p9 !) , but this time using the partition erase command first.
# /sbin/erase_image /dev/block/mmcblk0pN
prior to the mke2fs operation.
Click to expand...
Click to collapse
Ok, done, still no errors.
I've also tried writing test using dd if=/dev/zero of=/dev/block/partition bs=4096 (for partition p3 and p4) and again without any errors.

warpek said:
I used md5sum to co compare those files, here is mine:
part5.img 59071590099d21dd439896592338bf95
part8.img 59071590099d21dd439896592338bf95
Click to expand...
Click to collapse
Hmmmm. I did a little more looking at my own misc partition images, and they each contain 64 repeated (and identical!) blocks of information that are 1280 bytes long - a group of 8 (at minor offsets of 0x4000, 0x5000, 0x6000, 0x7000, 0xc000, 0xd000, 0xe000, 0xf000) that repeat 8 times every 64kB (major offset of 0x10000). If you want to attach one of your misc partition images, I can have a look at it for comparison (it is small - 512 kB, and should not contain any private data). Wait, I just realized: I have a 32GB WiFi N7 - is yours a 16GB?
warpek said:
Is there anything I can I do then?
Click to expand...
Click to collapse
I could shove a (near stock) boot.img and system.img backup from TWRP someplace, but the system image is huge. I don't have a convenient place to drop it - got any suggestions? In principle - barring any other errors - that should boot correctly so long as the ext4 filesystems on /data and /cache are intact and operating correctly.
warpek said:
I've also tried writing test using dd if=/dev/zero of=/dev/block/partition bs=4096 (for partition p3 and p4) and again without any errors.
Click to expand...
Click to collapse
Barring a tar or other archive file which we could unpack directly into (mounted) /system, that was going to be my next suggestion. Rats.
Maybe it is time to try the read/write tests with the /data partition?
Actually, before you do that, what were the dump lengths you got for each of your partitions? Here are mine (using bs=4096):
Code:
/dev/block/mmcblk0boot0 512 ( 2097152 bytes - 2.0MB)
/dev/block/mmcblk0boot1 512 ( 2097152 bytes - 2.0MB)
/dev/block/mmcblk0p1 3072 ( 12582912 bytes - 12.0MB) recovery
/dev/block/mmcblk0p2 2048 ( 8388608 bytes - 8.0MB) boot
/dev/block/mmcblk0p3 166400 (681574400 bytes - 650.0MB) system
/dev/block/mmcblk0p4 113408 (464519168 bytes - 443.0MB) cache
/dev/block/mmcblk0p5 128 ( 524288 bytes - 512kB) misc1?
/dev/block/mmcblk0p6 2560 ( 10485760 bytes - 10.0MB) -WTF?- "staging?"
/dev/block/mmcblk0p7 1280 ( 5242880 bytes - 5.0MB) mfg
/dev/block/mmcblk0p8 128 ( 524288 bytes - 512kB) misc2?
/dev/block/mmcblk0p9 ?? ( ?? bytes - ??MB) data
Note I didn't do my /data partition - I have a 32GB N7, so I suppose that means that /data is 30+ GB in size. Lazy and didn't want to wait.
---------- Post added at 01:40 PM ---------- Previous post was at 12:55 PM ----------
FYI,
shoving some TWRP backup images (system, boot) to my dropbox right now. Lightly-rooted stock. (Added su and SuperSu in /system, and altered default.prop in the boot image so that the secure flag is disabled and the adb daemon starts up straight away). Other than those changes, 100% stock, including kernel.
I'll send a PM when I figure out how Dropbox works.

bftb0 said:
Wait, I just realized: I have a 32GB WiFi N7 - is yours a 16GB?
Click to expand...
Click to collapse
Yes, I've got 16GB version.
bftb0 said:
I could shove a (near stock) boot.img and system.img backup from TWRP someplace, but the system image is huge. I don't have a convenient place to drop it - got any suggestions?
Click to expand...
Click to collapse
I can create ftp account on and send you login data in a private message. Will it be convenient for you?
bftb0 said:
Maybe it is time to try the read/write tests with the /data partition?
Click to expand...
Click to collapse
Yea, but ... now something really strange happened.
All partitions have disappeared. _I'm sure_ that I didn't zeroed the whole mmcblk0 device. Just the partition I mentioned before.
Code:
ls /dev/block
loop0 loop2 loop4 loop6 mmcblk0 mmcblk0bo
loop1 loop3 loop5 loop7 mmcblk0boot0 platform
fdisk -l /dev/block/mmcblk0
Disk /dev/block/mmcblk0: 15.7 GB, 15762194432 bytes
4 heads, 16 sectors/track, 481024 cylinders
Units = cylinders of 64 * 512 = 32768 bytes
Disk /dev/block/mmcblk0 doesn't contain a valid partition table
TWRP still starts but it takes more time.
bftb0 said:
Actually, before you do that, what were the dump lengths you got for each of your partitions? Here are mine (using bs=4096):
Click to expand...
Click to collapse
I don't have partition table now so I it is useless. But for the future use, can you tell me please how I can see this kind of dump?
Edit: I'd be grateful if anyone having Nexus 7 16GB paste output of command:
Code:
adb shell /sbin/fdisk -l /dev/block/mmcblk0
I hope I will be able to create proper partitions on my device then.
But I'm afraid of using fdisk to create partitions because this can lead to destroy current recovery which still starts.

warpek said:
Yes, I've got 16GB version.
I can create ftp account on and send you login data in a private message. Will it be convenient for you?
Click to expand...
Click to collapse
or you could just attach it - should be less than the XDA attachment size limit, and as I mentioned there is no private info in there.
Looking at my own dumped images, it looks like this same partitioning information appears in mmcblk0boot0 190 times (!!), and in mmcblk0boot1 256 times (!!). I need to extract them all and compare checksums to see if they are identical.
warpek said:
Yea, but ... now something really strange happened.
All partitions have disappeared. _I'm sure_ that I didn't zeroed the whole mmcblk0 device. Just the partition I mentioned before.
Code:
ls /dev/block
loop0 loop2 loop4 loop6 mmcblk0 mmcblk0bo
loop1 loop3 loop5 loop7 mmcblk0boot0 platform
fdisk -l /dev/block/mmcblk0
Disk /dev/block/mmcblk0: 15.7 GB, 15762194432 bytes
4 heads, 16 sectors/track, 481024 cylinders
Units = cylinders of 64 * 512 = 32768 bytes
Disk /dev/block/mmcblk0 doesn't contain a valid partition table
TWRP still starts but it takes more time.
I don't have partition table now so I it is useless. But for the future use, can you tell me please how I can see this kind of dump?
Click to expand...
Click to collapse
Holy ****.
(My info was just from collected from looking at the output of individual dd read commands on each partition)
Again, holy **** - that's a world of hurt. I suppose recovery might still be possible, but perhaps only with some exhaustive code review of how the mmc driver determines the partitioning. and possibly some very dangerous patching of areas in mmcblk0boot{0,1}. It does appear that partitioning information is stored redundantly in multiple places on the tablet.
I am wondering - if the partitioning information that the TWRP boot was somehow partially corrupted - then running "dd if=/dev/zero" to write without a "count=" size constraint might have caused an over-run past where the actual partition was supposed to live.
At this point, I wouldn't attempt any more writing operations - especially since TWRP doesn't know where anything lives any longer.
---------- Post added at 02:23 PM ---------- Previous post was at 02:16 PM ----------
For the purposes of rescue you might want to capture some dumps of mmcblk0boot0 and mmcblk0boot1
Since you can not mount the /sdcard to store the dumps temporarily, you should be able to stuff them into ramdisk temporarily and then pull them to your PC via adb in the same TWRP session:
C:\foo> adb shell
# mkdir /tmp/dumps
# dd if=/dev/block/mmcblk0boot0 bs=4096 of=/tmp/dumps/mmcblk0boot0.img
# dd if=/dev/block/mmcblk0boot1 bs=4096 of=/tmp/dumps/mmcblk0boot1.img
# exit
C:\foo> adb pull /tmp/dumps/
The worst that can happen here (if the partitioning for mmcblk0boot{0,1} is wrong - and huge - you'll wedge the TWRP session by filling memory.
Without committing to a lot of effort it looks like you are looking at RMA time.

bftb0 said:
I am wondering - if the partitioning information that the TWRP boot was somehow partially corrupted - then running "dd if=/dev/zero" to write without a "count=" size constraint might have caused an over-run past where the actual partition was supposed to live.
Click to expand...
Click to collapse
Yes, I suppose it could be the case.
bftb0 said:
For the purposes of rescue you might want to capture some dumps of mmcblk0boot0 and mmcblk0boot1
Click to expand...
Click to collapse
Done without problems.
bftb0 said:
Without committing to a lot of effort it looks like you are looking at RMA time.
Click to expand...
Click to collapse
[/QUOTE]
I don't want to bother you with too much digging, so maybe it's time to send my device back do the seller.
But before that ... I think I should wipe out TWRP.
Should I use dd on the whole mmcblk0 device to do that?
Nevertheless I'm really greateful for your time and efforts. Thank you very much.

warpek said:
Should I use dd on the whole mmcblk0 device to do that?
Click to expand...
Click to collapse
Hmmm. Dunno. At this point you might end up borking the bootloader trying something like that.
There have been other threads where folks reported returning devices without bothering to do any clean up - and without repercussions.
Seems believable; the folks that are tasked with repairing units under RMA are not approaching each one as if it were a forensic evaluation. From a pure business standpoint that would be a huge waste of time and money. If they ever get rewarded for anything they do, it's probably a throughput metric (devices repaired or scrapped per work shift). Your unit will be one of many.
Your thanks are welcome, but I have an interest in this anyway. I noticed in digging around that (rather bizarrely) there is a partition that TWRP identifies as "staging" (/dev/block/mmcblk0p6). The bizarre part of this is that a hexdump revealed a few strings that were unicode URLs for XDA's ad networks. !! ?? !!
That rather freaks me out - what the frick is user data (I suppose from web browsing?) doing in a partition that never gets mounted and is (apparently) not in any identify-able file system format?
Back when Amon_RA was packaging his recovery for various devices, he would use a STOCK KERNEL in the boot image for his recovery boot. That pretty much is a guarantee that the kernel drivers (e.g. for MTD/MMC) would behave no differently from the way the device manufacturer does things - including for important things like interpreting partition tables.
With TWRP and CWM we currently have no such assurances that subtle bugs have not crept in to important places unless we repackage their boot images to use stock kernels.
Anyway, I am trying to review what I *think* is partitioning information to see what I can figure out - but you probably shouldn't wait for me.
Good luck with your return.

I don't want to bother you with too much digging, so maybe it's time to send my device back do the seller.
But before that ... I think I should wipe out TWRP.
Should I use dd on the whole mmcblk0 device to do that?
Click to expand...
Click to collapse
Hi warpek, I don't mean to butt in to this thread but I encountered a similar issue to yours this past weekend that's gotten to the point where I can no longer turn on nor get into the bootloader anymore. My question is since our devices have been modified, do you know if there is there any chance that Asus could deny and void the warranty upon finding that out?
There have been other threads where folks reported returning devices without bothering to do any clean up - and without repercussions.
Click to expand...
Click to collapse
Alright guess I'll go give it a shot.

Hi fungosaurus,
For the benefit of the rest of the N7 community - could you say a few words about what ROM/kernel was on your tablet, and (if you know) about what the charge state of the battery was like when the first hint of problem occurred?
A few reports don't mean anything conclusive, but it sure is starting to look like something is going on with "low battery" / "can't turn on" syndromes ... which then unfold into full-blown disasters.

bftb0 said:
Hi fungosaurus,
For the benefit of the rest of the N7 community - could you say a few words about what ROM/kernel was on your tablet, and (if you know) about what the charge state of the battery was like when the first hint of problem occurred?
A few reports don't mean anything conclusive, but it sure is starting to look like something is going on with "low battery" / "can't turn on" syndromes ... which then unfold into full-blown disasters.
Click to expand...
Click to collapse
Oh yes of course. CM10.1 Jan 10 nightly with whichever kernel it came with. As far as I could tell the battery was fully charged when I could no longer power it back on or access the bootloader.
My issue was actually a bit complicated and I might've actually been the one to worsen it through my ignorance. I made a post on Reddit that describes in detail what happened. Does this help?

fungosaurus said:
Does this help?
Click to expand...
Click to collapse
Only time will tell - for instance if lots of folks start reporting troubles with the same kernel.
Sounds more like a hardware problem though. Thanks for the info.
I think I saw a recent news article stating that Asus is shipping about 1 million N7's per month now. If they have shipped 5 million cumulatively, and they have a defect rate of only 0.1% in the first year of service, that would be 5000 owners who might end up on message boards looking for help. Although - since rooters are presumably a small fraction of owners - I guess we should see a much smaller number of folks who are rooted AND experience hardware troubles.
@warpek - the data stored in the misc1/misc2 partitions does in fact appear to be partitioning data. But I don't think you can use "fdisk" for the mmcblk0 device in any event.

bftb0 said:
Hmmm. Dunno. At this point you might end up borking the bootloader trying something like that.
There have been other threads where folks reported returning devices without bothering to do any clean up - and without repercussions.
Click to expand...
Click to collapse
Yes, but to be sure that I won't have any problems while returning my device I zeroed the whole block device.
bftb0 said:
Your thanks are welcome, but I have an interest in this anyway. I noticed in digging around that (rather bizarrely) there is a partition that TWRP identifies as "staging" (/dev/block/mmcblk0p6). The bizarre part of this is that a hexdump revealed a few strings that were unicode URLs for XDA's ad networks. !! ?? !!
Click to expand...
Click to collapse
That is really astounding. Please let us now if you have any conclusions.
Meanwhile I'm sending my nexus to Asus.
Thanks again.

fungosaurus said:
My question is since our devices have been modified, do you know if there is there any chance that Asus could deny and void the warranty upon finding that out?
Click to expand...
Click to collapse
As bftb0 said it shouldn't be any problems but to be sure I zeroed the whole block device area before returning it back.

[TUTORIAL] How to resize system partition on Galaxy S3 for larger GAPPS

On newer Android versions, the system occupies more of the system partition and with GAPPS upgrades, larger GAPPS packages (such as stock and mini) cannot fit on the system partition of the 2012 Galaxy S3. You can just use pico or nano, but sometimes you want the full GAPPS, the real deal. This is also necessary for upcoming ROMs that come with GAPPS preinstalled, such as Pixel Experience. To do this, you must resize the system partition. You can do this by taking some of the space from the cache partition and giving it to the system partition.
PLEASE NOTE: This process is not risk-free! If you do not know what you are doing, I strongly advise against this procedure. I am not responsible for any bricked devices or issues you may face. You have been warned.
Requirements:
A Samsung Galaxy S3. I have the i9300 model, where I have tested it.
parted, downloadable from here. If it downloads as a txt file, delete the extension by renaming it without the txt.
TWRP installed on your device (available for i9300 from here.)
A computer with ADB installed and relevant drivers.
First of all, you must boot TWRP. Once booted, wipe all partitions in TWRP, including system. Reboot back into recovery. Then go into mount and deselect all devices, and uncheck the box saying "Mount system partition as read-only"
Secondly, connect your S3 and send parted to the device with the following command:
Code:
adb push <path_to_parted> /
Thirdly, enter the ADB shell with the following command:
Code:
adb shell
Now, give executable permission to the parted file with the following command:
Code:
chmod +x parted
Now run:
Code:
./parted /dev/block/mmcblk0
Run the print command and you will get a list of partitions. It should look something like:
Code:
Model: MMC VTU00M (sd/mmc)
Disk /dev/block/mmcblk0: 15.8GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Number Start End Size File system Name Flags
1 4194kB 8389kB 4194kB BOTA0
2 8389kB 12.6MB 4194kB BOTA1
3 12.6MB 33.6MB 21.0MB ext4 EFS
4 33.6MB 41.9MB 8389kB PARAM
5 41.9MB 50.3MB 8389kB BOOT
6 50.3MB 58.7MB 8389kB RECOVERY
7 58.7MB 92.3MB 33.6MB RADIO
8 92.3MB 1166MB 1074MB ext4 CACHE
9 1166MB 2777MB 1611MB ext4 SYSTEM
10 2777MB 3364MB 587MB ext4 HIDDEN
11 3364MB 3372MB 8389kB OTA
12 3372MB 15.8GB 12.4GB ext4 USERDATA
Make a note of the Start and End points for partitions 8 and 9 (CACHE and SYSTEM). In my case, the start and end points for partition 8 are 92.3 and 1166 and the start and end points for partition 9 are 1166 and 2777.
What we're going to do is delete these two partitions, then recreate them, but make the new partition 8 (Cache) smaller and allocate the space left to partition 9 (System).
Remove them with the following commands in parted:
Code:
./parted /dev/block/mmcblk0 rm 8
./parted /dev/block/mmcblk0 rm 9
Now recreate them with the following commands:
Code:
./parted /dev/block/mmcblk0 mkpart primary <cache_start> <cache_start+200>
./parted /dev/block/mmcblk0 mkpart primary <cache_end> <system_end>
Replace <cache_start> with the start of the former cache petition. In my case, it would be:
Code:
./parted /dev/block/mmcblk0 mkpart primary 92.3 292
./parted /dev/block/mmcblk0 mkpart primary 292 2777
Now name the partitions.
Code:
./parted /dev/block/mmcblk0 name 8 CACHE
./parted /dev/block/mmcblk0 name 9 SYSTEM
Then format them as ext4:
Code:
mke2fs -T ext4 /dev/block/mmcblk0p8
mke2fs -T ext4 /dev/block/mmcblk0p9
Run ./parted, followed by print, to check if the changes have been applied. If so, well done! You have successfully enlarged the system partition. Exit parted with the quit command.
Now configure and exit:
Code:
mount -a
exit
Reboot back into recovery and install any ROM of your choice. Once you've installed the ROM, reboot into recovery once again, and navigate to wipe --> advanced wipe, select system, tap repair or change filesystem, then resize.
You can now install any GAPPS of your choice. I've gotten LineageOS 16.0 working with mini gapps (Google Play Store + some Google apps) and it is working fine. You could make the system partition bigger by borrowing some more MB from the cache partition, or experimenting further by taking some from the HIDDEN partition. Remember, I am NOT responsible for any damage done when doing this. You assume full responsibility for any problems with the device. I hope this tutorial did help you, feel free to post here if it did or ask for help if you need it.

Did you experiment this process for a long time ? With so small a cache what could be the consequences ?
A finally do you know what is the use of HIDDEN partition ?
Great tutorial anyway.

barbe31 said:
Did you experiment this process for a long time ? With so small a cache what could be the consequences ?
Click to expand...
Click to collapse
Newer Android versions don't use up as much in the cache partition. If you're on say stock ICS or JB you may encounter some issues but if you're using LOS 15 or 16 it should work fine. I've used LOS 16 with GAPPS using this method for a while on my S3 and it's been fine.

ChasTechProjects said:
parted, downloadable from here.
Click to expand...
Click to collapse
Link says file doesn't exist.

petera703 said:
Link says file doesn't exist.
Click to expand...
Click to collapse
parted
drive.google.com

Cheers for that. I've been trying for some time to do the same thing on a Galaxy S4 Mini, working from a few variations of this process that I've found here and there, but never with any success. All appears to go well, with no errors, but it doesn't stick--the device just reverts to the previous partition sizes on reboot..
I've been using parted 3.2. I wondered if it would work with the parted you were using, but the one from your new link is 1.8 and doesn't even get as far for me (tried that one previously and it gets errors on my device).
If anyone know how to overcome the issue of resized partitions not surviving a reboot on Android, please help! I've been unable to solve it.
If it was plain Linux, it would be something to do with fstab, but fstab is never mentioned in the posts where people succeed in resizing Android partitions, so I think it must be something else, and perhaps something that varies from one device to another. Looking forward to any suggestions--thanks!

Can this idea/technique be applied to other *droid based devices
like Nook HD ?
[ Having same 'not enough space for the gaps' issue]