Database Users

[Q] SBF Help

Ok...Long story short I was on stock 2.2 & rooted with the Z4 root app. My phone was acting quirky. Gohst touches on the scteen...random reboots & the like. I usually do a battery pull & all is fine. But this time It got stuck in a boot loop..yay. Somehow I got it to boot iinto recover through clockwork mod & I did a recovery/restart. No luck. It stayed on the M logo. So I boot into recovery and do a data reset....Still stuck on the M when turnig on. So I figure This SBF thin Ive been hearing about doesnt seem to hard & seems like my only option for saving my DX RDS lite & drivers installed SBF 2.3.15 ready...GO!....no...RDS lite does its thing & says PASS. My phone however woll only go to Bootloader...cant get into recovery at all plus it now looks as follows
Bootloader
30.04
Err:A5,70,70,00,1F
MEM_MAP Blank
Service Req'd
Battery OK
OK to program
Connect USB
Data Cable
Any Ideas?!?!

Since your bootloader version is 30.04, try SBFing with a 2.3.34 SBF file.
Sent from my DROIDX using XDA App

What version windows are you using? 32 bit or 64 bit? Check out the site in my signature if you're looking for SBF files... They're there. Good luck, I'm sure you'll figure it out.

THANK YOU SOOO MUCH! sometimes the easiest things are the most overlooked

Ive got problem in a big way

Basically the jist of the story goes like this.. I was on the TBH official full gingerbread rooted OTA and i decided to try out a different rom so i made a backup and flashed it... the new rom i flashed i ended up not like it so i said ok whatever ill just nandroid back to my backup i had made.. so i nandroid back to my backup and im getting crazy force closes everywere and then my bootstrap dosent work anymore
So then i say ok ill just SBF it not a big deal.. So i proceed to flash the official .340 SBF file with RSD and it goes through the entire process... it flashes the entire thing fine and does all the checksum matches ETC and they all pass.. then at the VERY end of the process im talking like 99% done when it says "Switching to BP Pass Thru Mode" it FAILS and stops the entire process... I then proceed to unplug my phone and even if i pull the battery or do anything whatsoever it goes straight to the bootloader screen
I tried flashing it again... it always works and is perfectly fine up until 99% where it says switching to BP pass thru mode and then it fails and is over with... I even tried the gingerbread SBF file and nothing is working and the phones stuck at the bootloader screen with the "Code Corrupt" message
What can i do here? Ive never had problems with RSD and SBFing in the past and its always worked on this machine... Im also a little hesitant to bring it into verizon or something with this problem because its stuck on the bootloader screen which is obviously something im probobly not suppose to even know exists
Also i have no access to stock recovery or anything whatsoever

Joe92T said:
Basically the jist of the story goes like this.. I was on the TBH official full gingerbread rooted OTA and i decided to try out a different rom so i made a backup and flashed it... the new rom i flashed i ended up not like it so i said ok whatever ill just nandroid back to my backup i had made.. so i nandroid back to my backup and im getting crazy force closes everywere and then my bootstrap dosent work anymore
So then i say ok ill just SBF it not a big deal.. So i proceed to flash the official .340 SBF file with RSD and it goes through the entire process... it flashes the entire thing fine and does all the checksum matches ETC and they all pass.. then at the VERY end of the process im talking like 99% done when it says "Switching to BP Pass Thru Mode" it FAILS and stops the entire process... I then proceed to unplug my phone and even if i pull the battery or do anything whatsoever it goes straight to the bootloader screen
I tried flashing it again... it always works and is perfectly fine up until 99% where it says switching to BP pass thru mode and then it fails and is over with... I even tried the gingerbread SBF file and nothing is working and the phones stuck at the bootloader screen with the "Code Corrupt" message
What can i do here? Ive never had problems with RSD and SBFing in the past and its always worked on this machine
Click to expand...
Click to collapse
in the stock recovery do a factory rest...that will fix it

I have no access to stock recovery

Stock Recovery
Home+Power Button
Search to enter the menu and volume up+down to navigate and camera button to select

Ok. Problem, my brother in laws phone is stuck at bootup and stays. Tried to back up, to the back up and still stays stuck. Tried factory reset. And still nothing... Stuck. Any suggestions? Pls help and thank you in advance.
*WALK in the WORD*

SBF
dhaymond said:
Ok. Problem, my brother in laws phone is stuck at bootup and stays. Tried to back up, to the back up and still stays stuck. Tried factory reset. And still nothing... Stuck. Any suggestions? Pls help and thank you in advance.
*WALK in the WORD*
Click to expand...
Click to collapse
Put phone in bootloader mode power+volume down+camera and SBF to 2.3.340

[Q] Any ideas on unbricking?

I was running the 2.2 beta and attempted to upgrade to the 2.2 official from the moto site. It showed that my phone had no available upgrades so I attempted to flash back to the official 2.1 and now I get
Bootloader
91.7B
Err:A5,70,70,00,1F
MEM_MAP Blank
Service Req'd
Battery OK
OK to Program
Transfer Mode:
USB
Thats all I get and can't go any farther. I've tried reflashing about a dozen times using RSD and it simply will not work. RSD shows that it is working perfect and never pops up an error. Then when it gets to the reboot phase it just ends and says "PASS" under the Result column.

[Q] I am very stuck - Please Help Me

Hi All,
OK, I am both new and stuck, I have read every page in the unlocking Atrix thread and the one click root thread but I still do not know what is wrong.
I started off by running the one click root listed here, the root went fine and seemed to work, so I proceeded to install ROM Manager but when I tried to back up my phone the process failed.
I googled the error and it turned out that I did not unlock the Boot Loader, so I followed all the instructions that explained how to do it and nothing worked.
Thinking something must have gone wrong I went back to the one click root tool and unrooted my phone, I checked and everything was working and the phone seemed fine.
So then I started down the longer process of unlocking/rooting here , following the steps to the letter and here is where I come unstuck.
I have a UK carrier free phone so after downloading and installing the RSD Lite software I used the SBF_Flash file but when I selected this file the “Start” button remained greyed out.
I researched this issue and found the international flash called intl-fix-try1.sbf, this file looked like it was going to work, the start button became clickable and the process looked ok.
Once I clicked start the flashing started and percentage done went straight up to 98% in a matter of seconds, then as per the instructions the phone reboots but starts to reboot fully, the process % resets and starts from zero going up in increments of 3%, by the time the process is at 65% my phone has fully booted and is sitting at the lock screen, if I leave it there the process will go up to 100% but the status will still say "in progress" until I swipe the lock screen and then it says complete.
I was doubtful that the root had worked but just to make sure I proceeded to move the phone into Fastboot mode and go through the OEM Unlock process but once I have typed in fastbook oem unlock and hit enter the command prompt just comes up with a message waiting for device to respond and nothing more.
Please help as I am really stuck, I followed your guide to rooting my Galaxy tab 10.1 and had it sorted in minutes, my ICS rom installed and everything backed up via ROM Manager so I am not a total dummy.
Any suggestions?
Kind Regards
Chris

when you tried to flash the sbf on rsd lite did you have the phone pluged into the pc and have it put into rsd lite mode
prolly not if you still seen the lock screen
turn phone off then turn on by holding power button down and volume down
when u see fastboot word on the atrix use volume down to scroll to rsd mode then hit volume up and proceed with rsd lite and the sbf

Here might explain it little more..
http://briefmobile.com/how-to-unlock-the-atrix-4g-bootloader

That is exactly what I did, I have just done it again now . . . .
I clicked start
The console/flash starts,
The phones screen goes black,
Then the Red Motorola M appears
The flash progress jumps to 98%
Console Status says something about USB Pass through/phone rebooting
Then reboots and the Red Motorola M appears again
Then progress carries on and goes up and at 16% by now the phone is now fully in its boot process and by 26% it is at the swipe screen
I have the phone in USB debug mode and the usb connection set to mass storage. Could I be using the wrong SBF file?
Thanks

I have tried that method as well as it is uses a different sbf file called zomgunocklite.sbf when I use that file I an error saying sec_exception: febe, 35, 35 I googled that and it came up with a similar issue but it did not help.

So since my first post I have been speaking to ltdanno360 on here, I just wanted to take the time out to say a MASSIVE THANK YOU.
He has taken me through getting my phone back to a usable state and then all the way through fixing up with the latest bits and pieces.
I have taken up a good few hours of his time and I am now a very, very happy Atrix owner.
It is people like ltdanno360 that make this forum and the internet community such an amazing place. Just imagine driving home from work one day and you car breaks down on the freeway, a stranger stops and spends two hours of his day fixing your car before sending you on your way.
Things like that do not happen often in the real world but people like Danno are great examples of what humanity often misses.
Big Thanks Bro
Awesome guy, awesome forum.

SBF Problem! Help!

OK so my droid x has only booted into recovery mode for a while and I just left it that way after taking the battery out... I decided to try and fix it yesterday. I was fallowing this guide (droidxforums(DOT)com/forum/droid-x-sbf/12015-complete-droid-x-sbf-flashing-guide.html#post106311) and my bootloader is at 30.04. I was doing it on windows and used the latest RSD Lite. I think I need a full SBF so I tried the 5th one down (VRZ_MB810_2.3.34_1FF_01.zip) on this site sites(DOT)google.com/site/motosbf/droid-x-sbf-files
I SBFed it and every thing went fine... it said PASS and I thought I was done... correct? but when I rebooted it just booted right back to the bootloader. Plz Help

Does the bootloader screen happen to say MEM_MAP BLANK?
Sent from my Black Iced X

newmanx4 said:
Does the bootloader screen happen to say MEM_MAP BLANK?
Sent from my Black Iced X
Click to expand...
Click to collapse
Yes It does here is all it says:
Bootloader
30.04
Err:A5,70,70,00,1F
MEM_MAP Blank
Service Req'd
Battery OK
OK to Program
Connect USB
Data Cable
EDIT: Solved just SBF'ed .621 and worked perfectly! Thnx

Glad you worked it out. That's what happens when you try to install a previous system version over .621.
Sent from my Black Iced X