Database Users

Some console commands for P3300.

Below are some commands for Artemis.
For the moment still did not find a command to backup existing ROM.
There are some interesting ones related to debug and use of TFTP.
Commands are case sensitive.
Looks like battery is charging while in bootloader mode. It was not a case with Prophet.
regards,
fdp24
*******************************************
Cmd>fm
Wrong parameters of FM Command!!
Usage:
fm [command] [frequency]
where:
if[command] = i Initialize FM.
if[command] = o Power on FM.
if[command] = f Power off FM.
if[command] = t Tune FM channel to [frequency].
if[command] = a FM auto seek test.
if[command] = m Mono(1) or Stereo(0).
if[command] = v Volume (0x00 - 0x0F).
if[command] = u Mute(0)
if[command] = g AGC(1)
if[command] = h Set seek threshold (0x00 - 0xFF).
if[command] = s Seek Up(1) or Down(0).
if[command] = r Get RSSI (0x00 - 0xFF).
if[command] = c Get current channel [frequency].
if[command] = d Get RDS data (1 - 10 groups of data).
*******************************************
Cmd>cpldver
xsvfExecute - CpldType=1
SUCCESS - Completed XSVF execution.
CPLD Ver[0]=1
CPLD Ver[1]=FC
CPLD Ver[2]=26
CPLD Ver[3]=5
Unknown yet.
*******************************************
Cmd>SetDsbDBGMSGT
Unknown yet.
*******************************************
Cmd>ReadExtROM
Dump Ext ROM to MTTY terminal
*******************************************
Cmd>WLANReset
Usage:
WLANReset 1(or0)
set SDIO: 0-WLAN ;1-SDMC.
Cmd>WLANReset 0
WLANReset(FALSE)
Cmd>WLANReset 1
WLANReset(TRUE)
*******************************************
Cmd>SDSelect
Usage:
SDSelect 1(or0)
set SDIO: 0-WLAN ;1-SDMC.
Cmd>SDSelect 1
Select SD Card
*******************************************
Cmd>emapiWlanMac
Notice: This MAC address takes effect only when your platform is EEPRON-less configuration. Please use (emapiTest) to verify it !
Copying GSM DATA image to SDRAM:00004000
Wlan data header ++++++++++++++++++++
Signature : 0xEE1250
UpdateStatus : 0x2
UpdateCount : 0xA
BodyLength : 0x1A1
BodyCRC : 0x4349311B
Wlan data header --------------------------
0x00000000
0x00000009
0x0000002D
0x000000D2
0x000000D5
0x000000FB
*******************************************
Cmd>emapiTest
+emapiTest
1. Power on WLAN
2. Reset WLAN
3. Switch MUX to WLAN
4. Enable WLAN clock
5. Init WLAN SDIO interface
6. DeviceID Test
DeviceID = 403xxxx
EEPROMless configuration!
-emapiTest
*******************************************
Cmd>emapiPwrDwn
*******************************************
Cmd>emapiRead
Parameter Wrong!!
*******************************************
Cmd>getdevinfo
Need password!
*******************************************
Cmd>wdata
Usage:
wdata [StartAddr Len]
Write data to memory(if write to ROM, need erase first).
StartAddr : Start address of memory.
Len : How many bytes will be written.
Length must not more than 0x10000 bytes(buffer limitation).
Write to RAM: 4 bytes(CRC checksum limitation).
1 byte(in user mode).
Write to ROM: 4 bytes(CRC checksum limitation).
2(16-bit)/4(32-bit) bytes(in user mode).
Write to ROM(16-bit data bus): 32 bytes(writebuffer mode).
Write to ROM(32-bit data bus): 64 bytes(writebuffer mode).
Length must be 4 bytes boundary(CRC checksum) if not in user mode.
After command execute, then send out the data to terminal.
Data format: HTCS(4 bytes)+DATA+checksum(4 bytes, if not in user mode)+HTCE(4 bytes).
*******************************************
Cmd>password
Usage:
password [String]
Enter the password string to enable wdata, erase and rbmc functions.
*******************************************
Cmd>set
Usage:
set [Type Value]
Set control flags.
Type(hex) : Control function types.
Value(hex) : Setting values for types.
Type 1(Operation mode): 1(auto) and 0(user).
Type 2(Back color on/off): 1(on) and 0(off).
Type 4(Front color value): 16 bits data
Type 5(Background color value): 16 bits data
Type 6(Set color of screen): Fill color to whole screen one time.
Current flag settings:
Type 1(Operation mode flag): g_cOpModeFlag=(0x0).
Type 2(Back color flag): cBackColorShowFlag=(0x0).
Type 4(Front color): g_dwFColor24bit=(0x0).
Type 5(Background color): g_dwBColor24bit=(0xFFFFFF).
Type 6(Set color of screen): None.
Type 32: Unlock Flash Command
Set control flags.
*******************************************
Cmd>SetDebugMethod
Copying GSM DATA image to SDRAM:00004000
Default DebugTransport Value =00000000
Current Usage:
0 No Debug
A UART MTTY Output Debug Message
B USB MTTY Output Debug Message
*******************************************
Cmd>checksum
Usage:
checksum addr len
Return CRC checksum of memory.
In user mode: Show 4 bytes of CRC checksum value on display of terminal.
In auto mode: Send 4 bytes of CRC checksum value to terminal with data format.
*******************************************
Cmd>ResetDevice
no comments
*******************************************
**When CID is locked.
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
Not allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
**When CID is locked.
*******************************************
**When CID unlocked
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==
**When CID unlocked
*******************************************
Cmd>GPSRouting
Dump code to mtty console.
*******************************************
Cmd>BTRouting
Dump code to mtty console.
*******************************************
Cmd>BTRouting
+GSM_Modem_Init : include DAGON
Copying GSM DATA image to SDRAM:00004000
GSM - dwSize = 3479D
GSM Page0
GSM - dwSize = 45457
GSM Page1
GSM - dwSize = 4B768
GSM Page2
GSM - dwSize = 4E0A9
GSM Page3
GSM - dwSize = 4B4C4
GSM Page4
GSM - dwSize = 4C71F
GSM Page5
GSM - dwSize = 2958E
GSM Page6
GSM - dwSize = E8D8
GSM Page7
Copying GSM CODE image to SDRAM:00000000
ARMBOOT = 1 --> boot from CS3
Reset ARM 7 -- ok
Please close MTTY USB connection and open BT Testing program...
*******************************************

Wow.. Very VERY nice!

Wow fdp24
Please how did you found out all those comands ?
I'm curious and in the need of unbricking some.

can we use any of therse comands to make the SimLockTool_Artemis_Excalibur tool work

Please Help, I don't known anymore.........???

Hello,
I'm New here....
This is my first T-mobile sda1(Germany) without camera to upgrade/downgrade
I want downgrade back WM2003, and now this mistake!!!
What should I do?
l c:/os.bin
clean up the image temp buffer at 0x8C080000 Length 0x01B00000
MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>info 2
GetDeviceInfo=0x00000002
Load Binary NORMAL partition: data from DiskOnChip to RAM
Start to read bianry partition.
Read binary partition successfully.
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
Load Binary NORMAL partition: data from DiskOnChip to RAM
Start to read bianry partition.
Read binary partition successfully.
HTCST-MOB001 1Å›™HTCE
Cmd>

WP8 FM Internal Settings

Missing FM? This is the thread to watch then! I'm digging to find out everything there is to know about it here. This is everything I've found in the last 30 minutes.
Code:
FM Driver
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Services\qcfmtransport]
"DisplayName"="@qcfmtransport8960.inf,%Bus.SVCDESC%;QUALCOMM FM Transport Driver"
"ErrorControl"=dword:00000001
"Group"="Extended Base"
;Value:\SystemRoot\System32\drivers\qcfmtransport8960.sys
"ImagePath"=hex(2):5C,00,53,00,79,00,73,00,74,00,65,00,6D,00,52,00,6F,00,6F,00,74,00,5C,00,53,00,79,00,73,00,74,00,65,00,6D,00,33,00,32,00,\
5C,00,64,00,72,00,69,00,76,00,65,00,72,00,73,00,5C,00,71,00,63,00,66,00,6D,00,74,00,72,00,61,00,6E,00,73,00,70,00,6F,00,\
72,00,74,00,38,00,39,00,36,00,30,00,2E,00,73,00,79,00,73,00,00,00
"Start"=dword:00000001
"Tag"=dword:0000000E
"Type"=dword:00000001
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DeviceIds\QWCN\QCOM2150]
"qcfmtransport8960.inf"=hex:01,FF,00,00
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DeviceIds\{4d36e97d-e325-11ce-bfc1-08002be10318}]
"qcfmtransport8960.inf"=hex(0):
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverInfFiles\qcfmtransport8960.inf]
"Active"="qcfmtransport8960.inf_arm_96763fb718a23855"
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855]
@="qcfmtransport8960.inf"
"Provider"="Microsoft"
"SignerName"=""
"SignerScore"=dword:0D000003
"Version"=hex:FF,FF,05,00,00,00,00,00,7D,E9,36,4D,25,E3,CE,11,BF,C1,08,00,2B,E1,03,18,00,C0,06,F4,11,63,CE,01,00,00,E5,0B,00,00,01,00,\
00,00,00,00,00,00,00,00
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855\Configurations\Bus_Vendor.NT]
"ConfigFlags"=dword:00000000
"Service"="qcfmtransport"
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855\Configurations\Bus_Vendor.NT\Properties\{a45c254e-df1c-4efd-8020-67d146a850e0}]
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855\Configurations\Bus_Vendor.NT\Properties\{a45c254e-df1c-4efd-8020-67d146a850e0}\0019]
@=hex(ffff0013):01,00,04,90,00,00,00,00,00,00,00,00,00,00,00,00,14,00,00,00,02,00,C4,00,05,00,00,00,00,00,14,00,00,00,00,10,01,01,00,00,\
00,00,00,05,12,00,00,00,00,00,38,00,00,00,00,10,01,0A,00,00,00,00,00,0F,03,00,00,00,00,04,00,00,52,77,E4,E9,43,3B,DB,AC,\
8C,30,3E,83,EE,0C,AD,9D,F4,16,21,E5,0A,BD,A8,7F,B6,5E,2B,49,D5,C8,3A,4A,00,00,24,00,00,00,00,10,01,05,00,00,00,00,00,05,\
15,00,00,00,D1,A7,1A,A1,53,9E,65,2F,4B,7F,77,1A,06,04,00,00,00,00,24,00,00,00,00,10,01,05,00,00,00,00,00,05,15,00,00,00,\
D1,A7,1A,A1,53,9E,65,2F,4B,7F,77,1A,80,04,00,00,00,00,28,00,00,00,00,10,01,06,00,00,00,00,00,05,50,00,00,00,E2,CF,C3,5F,\
9F,4F,F9,38,0C,29,6B,A6,99,2B,3B,07,77,65,BF,0E
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855\Configurations\Bus_Vendor.NT\Properties\{a45c254e-df1c-4efd-8020-67d146a850e0}\001D]
@=hex(ffff0007):00,01,00,00
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855\Descriptors\QWCN\QCOM2150]
"Configuration"="Bus_Vendor.NT"
"Description"="%bus.devicedesc%"
"Manufacturer"="%stdmfg%"
[HKEY_LOCAL_MACHINE\SYSTEM\DriverDatabase\DriverPackages\qcfmtransport8960.inf_arm_96763fb718a23855\Strings]
"bus.devicedesc"="QUALCOMM FM Transport Driver "
"stdmfg"="(Standard system devices)"
Code:
FM Settings - Microsoft.Audio.AudioTuner.reg
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Tuner\Audio\FmRadio\Regions\1]
"FrequencyMin"=dword:0001575C
"FrequencyMax"=dword:0001A57C
"FrequencySpacing"=dword:000000C8
"Emphasis"=dword:00000001
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Tuner\Audio\FmRadio\Regions\2]
"FrequencyMin"=dword:000155CC
"FrequencyMax"=dword:0001A5E0
"FrequencySpacing"=dword:00000064
"Emphasis"=dword:00000000
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Tuner\Audio\FmRadio\Regions\3]
"FrequencyMin"=dword:000128E0
"FrequencyMax"=dword:00015F90
"FrequencySpacing"=dword:00000064
"Emphasis"=dword:00000000
[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\WINEVT\Publishers\{CA48BE7D-CE1C-4CA9-A00D-DB5359E3A9A1}]
@="Microsoft-WindowsPhone-AudioTuner"
"ResourceFileName"="C:\\windows\\System32\\AudioTunerApi.dll"
"MessageFileName"="C:\\windows\\System32\\AudioTunerApi.dll"
"Enabled"=dword:00000001
[HKEY_LOCAL_MACHINE\Software\Classes\CLSID\{B8B32416-C9C2-4817-8167-DA970B54320B}]
@="FmReceiver"
[HKEY_LOCAL_MACHINE\Software\Classes\CLSID\{B8B32416-C9C2-4817-8167-DA970B54320B}\InProcServer32]
;Value:%SystemRoot%\System32\AudioTunerApi.dll
@=hex(2):25,00,53,00,79,00,73,00,74,00,65,00,6D,00,52,00,6F,00,6F,00,74,00,25,00,5C,00,53,00,79,00,73,00,74,00,65,00,6D,00,33,00,\
32,00,5C,00,41,00,75,00,64,00,69,00,6F,00,54,00,75,00,6E,00,65,00,72,00,41,00,70,00,69,00,2E,00,64,00,6C,00,6C,00,00,00
"ThreadingModel"="Free"
[HKEY_LOCAL_MACHINE\Software\Classes\Interface\{5E708E9F-8500-41ca-85BC-53ED2691D5C7}]
@="IAudioTuner"
[HKEY_LOCAL_MACHINE\Software\Classes\Interface\{42C0C635-EC96-40ac-953E-4FF722ED0FFF}]
@="IFmReceive"
[HKEY_LOCAL_MACHINE\Software\Classes\Interface\{12E36A78-1DDC-415a-84D9-2A92D5C42D07}]
@="IRdsCapture"
Code:
FM Driver Settings - Qualcomm.QC8960.qcfmminiport.reg
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Tuner\Audio\FmRadio]
"MiniportDll"="qcfmminiport.dll"
"newSearchAlgorithm"=dword:00000000
"NoOfSiNRSamples"=dword:0000000A
"IntDetTHLow"=dword:0000006D
"IntDetTHHigh"=dword:00000073
"SiNRTH"=dword:00000003
"CFOTH12"=dword:00003A98
"RMSSIFirstStage"=dword:FFFFFF90
"SiNRFirstStage"=dword:00000000
"SiNRFinalStage"=dword:00000003
Code:
FM FINAL SETTING - Microsoft.Media.Apps.reg
[HKEY_LOCAL_MACHINE\Software\Microsoft\FMRadio\OEM]
"NotPresent"=dword:00000001
Code:
qcfmminiport.dll searchable strings
FDllMain FM: QFM: +%s
FM: QFM: -%s
CreateAdapterDriver AdapterDriver::CreateInstance AdapterDriver::~AdapterDriver
AdapterDriver::AddRef AdapterDriver::Release AdapterDriver::QueryInterface
AdapterDriver::CreateMiniportTunerDevice
+cleanup
-cleanup
MiniportFmRxDevice::read_thread FM: Miniport: read_thread: SSR is happening
FM: Miniport: read_thread: NULL event pointer received
FM: Miniport: read_thread: FM_RX_EV_ENABLE_RECEIVER success, time stamp %lu
FM: Miniport: read_thread: FM_RX_EV_ENABLE_RECEIVER failed
FM: Miniport: read_thread: calling Enable AsycComplete context(0x%08p)
FM: Miniport: read_thread: FM_RX_EV_DISABLE_RECEIVER success
FM: Miniport: read_thread: FM_RX_EV_DISABLE_RECEIVER failed
FM: Miniport: read_thread: calling Disable AsycComplete context(0x%08p)
FM: Miniport: read_thread: FM_RX_CANCEL_SEARCH_CMD
FM: Miniport: read_thread: cmd complete received for command %u
FM: Miniport: read_thread: FM_RX_TUNE_STATUS_EVT
FM: Miniport: read_thread: calling Tune/Region Asyc context = 0x%08p !
FM: Miniport: read_thread: calling Tune complete - Tune/Seek Asyc context = 0x%08p
FM: Miniport: read_thread: ### tune at cancelled frequency
FM: Miniport: read_thread: calling Seek cancelled - Tune/Seek Asyc context = 0x%08p
FM: Miniport: read_thread: calling Seek complete - Tune/Seek Asyc context = 0x%08p, time stamp %lu
FM: Miniport: read_thread: user defined band tune/seek complete, time stamp %lu
FM: Miniport: read_thread: cmd status event for Tune received
FM: Miniport: read_thread: calling Seek failure Async context = 0x%08p
FM: Miniport: read_thread: cmd status event for Search received, status %u
FM: Miniport: read_thread: calling Cancel Seek Failure - Tune/Seek Asyc context = 0x%08p
FM: Miniport: read_thread: calling Seek Failure - Tune/Seek Asyc context = 0x%08p
FM: Miniport: read_thread: command status received for unknown command %u
FM: Miniport: read_thread: ProcessRdsGroup failed
FM: Miniport: read_thread: FM_RX_SEARCH_IN_PROGRESS_EVT!
FM: Miniport: read_thread: FM_RX_SEARCH_COMPLETE_EVT!
FM: Miniport: read_thread: FM_RX_STEREO_STATUS_EVT!
FM: Miniport: read_thread: unknown event with opcode %x!
MiniportFmRxDevice::CreateInstance FM: Miniport: - CreateInstance Invalid pPortTunerDevice
FM: Miniport: - CreateInstance Invalid ppMiniportTunerDevice
FM: Miniport: - CreateInstance Invalid pDevice
FM: Miniport: CreateInstance - Initialize failed, hr = %x
FM: Miniport: CreateInstance - QueryInterface failed
MiniportFmRxDevice::MiniportFmRxDevice MiniportFmRxDevice::~MiniportFmRxDevice MiniportFmRxDevice::AddRef MiniportFmRxDevice::Release MiniportFmRxDevice::QueryInterface FM: Miniport: - QueryInterface Invalid ppvObject
FM: Miniport: - QueryInterface Invalid Interface
MiniportFmRxDevice::Initialize FM: Miniport: - Initialize Invalid pMddTunerDevice
FM: Miniport: ::Initialize - QueryInterface failed
FM: Miniport: : Initialize - QFM init successful
FM: Miniport: : Initialize - QFM init failed with error %d
FM: Miniport: : Initialize: Creating thread failed
FM: Miniport: : Initialize: Thread creation successful
FM: Miniport: : Initialize: Creating power event failed
FM: Miniport: : Initialize: Creating tune event failed
FM: Miniport: : Initialize: Creating cancel seek event failed
MiniportFmRxDevice::GetPowerState FM: Miniport: - GetPowerState Invalid pPowerState
MiniportFmRxDevice::SetPowerState FM: Miniport: SetPowerState: context is NULL
FM: Miniport: Already in requested power state
FM: Miniport: SetPowerState: WaitForSingleObject timeout failure
FM: Miniport: SetPowerState: Tune WaitForSingleObject timeout failure
FM: Miniport: powering on..., time stamp is %lu
FM: Miniport: SetPowerState: Failed to enable QFM! (%d)
FM: Miniport: SetPowerState: QFM enabled...Async Context = 0x%08p
FM: Miniport: SetPowerState: Failed to disable QFM! (%d)
FM: Miniport: SetPowerState: QFM disabled... Async Context = 0x%08p
MiniportFmRxDevice::GetVolume FM: Miniport: - GetVolume plVolume
FM: Miniport: GetProperty: FM is not turned on
MiniportFmRxDevice::SetVolume MiniportFmRxDevice::SetRegionParams FM: Miniport: SetRegionParams: FM is not turned on
FM: Miniport: SetRegionParams: context is NULL
FM: Miniport: SetRegionParams - SetRegionParams Invalid pRegionParams
FM: Miniport: SetRegionParams - SetRegionParams No Change in Parameters
MiniportFmRxDevice - SetRegionParams Busy
FM: Miniport: - SetPowerState Busy
FM: Miniport: SetRegionParams: Tune WaitForSingleObject timeout failure
FM: Miniport: config: Failed to config QFM! (%d)
FM: Miniport: config: Beginning Tune/config! Async Context = 0x%08p
MiniportFmRxDevice::Tune FM: Miniport: Tune: m_fTune is %d, m_fSeek is %d
FM: Miniport: Tune: FM is not turned on
FM: Miniport: Tune: context is NULL
Tune - Frequency out of band. Freq = 0x%08x
FM: Miniport: Tune - There is a pending region change. Busy
FM: Miniport: Tune: calling Tune Asyc context = 0x%08p
FM: Miniport: Tune: Failed to tune QFM! (%d)
FM: Miniport: Tune: Beginning Async Tune/Seek! Async Context = 0x%08p
FM: Miniport: Tune: FM Radio off!
MiniportFmRxDevice::GetTunedFrequency FM: Miniport: - GetTunedFrequency pFrequency
FM: Miniport: GetTunedFrequency: FM is not turned on
FM: Miniport: GetTunedFrequency: Failed to get station params! error %d
MiniportFmRxDevice::Seek Seek: m_fTune is %d, m_fSeek is %d FM: Miniport: Seek: FM is not turned on
Seek: context is NULL
Seek - There is a pending region change. Busy
Seek - SetPowerState Busy
Seek: m_TuneHandle is NULL Seek: Tune WaitForSingleObject timeout failure
Seek: Failed to seek QFM! (%d) Seek: Beginning Async Tune/Seek! Async Context = 0x%08p, SeekDir(%d) Seek: FM turned off.!
MiniportFmRxDevice::CancelSeek FM: Miniport: CancelSeek: m_fTune is %d, m_fSeek is %d FM: Miniport: CancelSeek: FM is not turned on
CancelSeek: No seek active!
CancelSeek: Failed to cancel seek QFM! (%d) CancelSeek failed.
MiniportFmRxDevice::RdsStartCapture FM: Miniport: RdsStartCapture: FM is not turned on
RdsStartCapture: Failed to start RDS capture! error (%d)
MiniportFmRxDevice::RdsStopCapture FM: Miniport: RdsStopCapture: FM is not turned on
RdsStopCapture: Failed to stop RDS capture! error (%d)
MiniportFmRxDevice::GetProperty FM: Miniport: GetProperty Invalid pvPropData/pcbReturn
MiniportFmRxDevice - GetProperty Invalid pRssiProp size
MiniportFmRxDevice - GetProperty Invalid pStereoModeProp size
MiniportFmRxDevice - GetProperty Invalid pAntennaTypeProp size
MiniportFmRxDevice - GetProperty Not Supported
MiniportFmRxDevice::SetProperty FM: Miniport: SetProperty: FM is not turned on
MiniportFmRxDevice - SetProperty Invalid pvPropData
FM: miniport: Sending seek command down, time stamp %lu
MiniportFmRxDevice - SetProperty Not Supported
Reset Read FM: QFM : Read : Invalid parameter
FM: QFM: Read : GetOverlappedResult failed with error %d
FM: QFM: Read: In default case
FM: QFM: Read: status is %d
FM: QFM: Read: FM_RX_GET_PINCONNECTIVITY_RESULTS_CMD bt_test_id %u, bt_test_result %u, fm_test_id %u, fm_test_result %u
FM: QFM: get station params is success
FM: QFM: get station params failed, error %u
FM: QFM: do calibration is success
FM: QFM: do calibration failed, error %u
old new FM: QFM: Default data read success, search algorithm is %s
FM: QFM: Default data read failed with error %u
FM: QFM: Default data write success
FM: QFM: Default data write failed with error %u
FM: QFM: command status received for unknown command
FM: QFM: Tune status event received
FM: QFM: FM_RX_PROGRAM_SERVICE_EVT: PS is %s, no. of strings %d
Write FM: QFM: Write: SSR is happening
FM: QFM : Write : Invalid parameter
FM: QFM: Write : GetOverlappedResult failed with error %d
FM: QFM: Write: In default case
FM: QFM: Write: successful
FM: QFM: Write: Wait failed with returned %lu, error %lu
Init FM: QFM: Init: WAN Event creation failed with error %lu
FM: QFM: Init: Thread creation failed with error %lu
FM: QFM: Init: SSR Thread creation failed with error %lu
FM: QFM: Init: Event creation failed with error %lu
FM: QFM: Init: Creating write evt failed with error %lu
FM: QFM: Init: Creating read evt failed with error %lu
FM: QFM: Init: Creating SSR notification evt failed with error %lu
\\.\qcfmtransportdriver FM: QFM: Init: Opening FM transport driver handle failed
FM: QFM: Init: Opening transport driver handle successful
DeInit FM: QFM: cancelling the SSR request success
FM: QFM: error cancelling the SSR request, error %lu
ReadRegistryKeys SYSTEM\ControlSet001\Control\Tuner\Audio\FmRadio FM: QFM: Opening FM reg key %s has failed with error %x
newSearchAlgorithm FM: QFM: Error reading search algorithm type key: %x
FM: QFM: search algorithm: %x
NoOfSiNRSamples FM: QFM: Error reading No of SiNR samples key: %x
IntDetTHLow FM: QFM: Error reading IntDetTHLow key: %x
IntDetTHHigh FM: QFM: Error reading IntDetTHHigh key: %x
SiNRTH FM: QFM: Error reading SiNR key: %x
CFOTH12 FM: QFM: Error reading CFOTH12 key: %x
FM: QFM: CFOTH12 read from registry is %x, %d
FM: QFM: CFOTH12 is %x %x %x %x
RMSSIFirstStage FM: QFM: Error reading RMSSIFirstStage key: %x
FM: QFM: RMSSIFirstStage %x %d
SiNRFirstStage FM: QFM: Error reading SiNRFirstStage key: %x
FM: QFM: SiNRFirstStage read from registry is %x, %d
SiNRFinalStage FM: QFM: Error reading SiNRFinalStage key: %x
bIsFmCalibrationDone FM: QFM: Error reading key: %x
FM: QFM: Calibration flag: %x
procCalData WriteRegKeys FM: QFM: Error writing calibration flag in registry: %x
FM: QFM: Error writing proc cal data in the registry: %x
DoCalibration FM: QFM: Do Calibration is successful
FM: QFM: Do Calibration failed with error %d
FM: QFM: Sending proc cal data is successful
FM: QFM: proc cal data failed with error %d
GetDefaultRxConfig FM: QFM: GetDefaultRxConfig is successful
FM: QFM: GetDefaultRxConfig failed with error %d
SetDefaultRxConfig FM: QFM: SetDefaultRxConfig is successful
FM: QFM: SetDefaultRxConfig failed with error %d
Enable FM: QFM: Enable is successful
FM: QFM: Enable failed with error %d
Disable FM: QFM: Disable is successful
FM: QFM: Disable failed with error %d
GetStationParams FM: QFM: GetStationParams is successful
FM: QFM: GetStationParams failed with error %d
SetStation FM: QFM: Tuning to freq %u
FM: QFM: Tune is successful
FM: QFM: Tune failed with error %d
ConfigRegion FM: QFM: ConfigRegion: Error setting frequency spacing (%lu) FM: QFM: ConfigRegion is successful
FM: QFM: ConfigRegion failed with error %d
ConfigUserDefinedRegion FM: QFM: ConfigUserDefinedRegion is successful
FM: QFM: ConfigUserDefinedRegion failed with error %d
Search FM: QFM: Search is successful
FM: QFM: Search failed with error %d
CancelSearch FM: QFM: CancelSearch is successful
FM: QFM: CancelSearch failed with error %d
SetRdsGroupOptions FM: QFM: SetRdsGroupOptions is successful
FM: QFM: SetRdsGroupOptions failed with error %d
FM: QFM: SetRdsGroupOptions: setting RDS group processing is successful
FM: QFM: SetRdsGroupOptions: setting RDS group processing failed with error %d
SetAntennaType FM: QFM: Setantenna type is successful
FM: QFM: Setantenna type failed with error %d
SetMuteMode FM: QFM: SetMuteMode successful
FM: QFM: SetMuteMode failed with error %d
SetHlsi FM: QFM: SetHlsi is successful
FM: QFM: SetHlsi failed with error %d
SetStereoMode FM: QFM: SetStereoMode successful
FM: QFM: SetStereoMode failed with error %d
SetNotchControl FM: QFM: SetNotchControl successful
FM: QFM: SetNotchControl failed with error %d
SetSignalThreshold FM: QFM: SetSignalThreshold successful
FM: QFM: SetSignalThreshold failed with error %d
GetSignalThreshold FM: QFM: GetSignalThreshold successful
FM: QFM: GetSignalThreshold failed with error %d
GetRDSGrpCounters FM: QFM: GetRDSGrpCounters successful
FM: QFM: GetRDSGrpCounters failed with error %d
SetRdsGroupProcessing FM: QFM: SetRdsGroupProcessing successful
FM: QFM: SetRdsGroupProcessing failed with error %d
GetPS GetPinConnResult FM: QFM: GetPinConnResult is successful
FM: QFM: GetPinConnResult failed with error %d
FM: QFM: activeBand is %d
query_rf_band_info_and_set_notch_filter FM: QFM: qmi_client_send_msg_sync failed with error %x
FM: QFM: band is above 1 GHz, setting high pass filter
FM: QFM: band is below 1 GHz, setting low pass filter
wan_cb FM: QFM: QMI_WDS_PKT_SRVC_STATUS_IND_V01 received
wan_conc_thread FM: QFM: qmi_client_get_service_instance for nas service failed with error %x
FM: QFM: qmi_client_init for nas service failed with error %x
FM: QFM: qmi_client_get_service_instance for wds port %d failed with error %x
FM: QFM: qmi_client_init for wds port %d failed with error %x
FM: QFM: qmi_client_send_msg_sync failed with error %x for WDS port %u
FM: QFM: number of data calls up are %d
FM: QFM: qmi_client_release failed with error %x
FM: QFM: WaitForSingleObject failed with error %x
FM: QFM: qmi_client_message_decode failed with error %x
FM: QFM: No. of data calls is 0, resetting the notch filter
ssr_thread FM: QFM : ssr_thread : Invalid parameter
FM: QFM: ssr_thread : GetOverlappedResult is success
FM: QFM: ssr_thread : GetOverlappedResult failed with error %d
FM: QFM: ssr_thread: In default case, GetLastError returned %lu
FM: QFM: ssr_thread: successful
P:\fm\rel\8.2.1.1\arm\Release\qcfmminiport.pdb
DisableThreadLibraryCalls OutputDebugStringA
3 WaitForSingleObject ' SetEvent InitializeCriticalSection
CreateEventA LeaveCriticalSection GetLastError
EnterCriticalSection % ResetEvent
DeleteCriticalSection CloseHandle CreateThread
GetTickCount64 CreateFileA ' RegSetValueExA
RegQueryValueExA GetOverlappedResult RegOpenKeyExA
CancelIoEx DeviceIoControl RegCloseKey
api-ms-win-core-libraryloader-l1-1-1.dll api-ms-win-core-debug-l1-1-1.dll
api-ms-win-core-synch-l1-2-0.dll api-ms-win-core-errorhandling-l1-1-1.dll
api-ms-win-core-handle-l1-1-0.dll api-ms-win-core-processthreads-l1-1-1.dll
api-ms-win-core-sysinfo-l1-2-0.dll api-ms-win-core-file-l1-2-0.dll
api-ms-win-core-registry-l1-1-0.dll api-ms-win-core-io-l1-1-1.dll
sprintf_s –free malloc MSVCR110.dll ;_malloc_crt_amsg_exit _initterm_e _initterm ]__C_specific_handler ^__CppXcptFilter ð_calloc_crt Ð_onexit *_lock †__dllonexit _unlock {__clean_type_info_names_internal qmi_client_release qmi_client_send_msg_sync
qmi_client_message_decode qmi_client_init
qmi_client_get_service_instance qccium8960.dll EncodePointer DecodePointer QueryPerformanceCounter GetCurrentThreadId GetSystemTimeAsFileTime api-ms-win-core-util-l1-1-0.dll api-ms-win-core-profile-l1-1-0.dll àmemset Ümemcpy Ûmemcmp c__CxxFrameHandler3 qcfmminiport.dll CreateAdapterDriver
<?xml version='1.0' encoding='UTF-8' standalone='yes'?>
<assembly xmlns='urn:schemas-microsoft-com:asm.v1' manifestVersion='1.0'>
<trustInfo xmlns="urn:schemas-microsoft-com:asm.v3">
<security>
<requestedPrivileges>
<requestedExecutionLevel level='asInvoker' uiAccess='false' />
</requestedPrivileges>
</security>
</trustInfo>
</assembly>
Code:
File was located at /test/QCFMFTMApp.exe from the Lumia 928 GDR2 ROM - dotPeek couldn't recognize the file, so here is all the searchable text.
OpenDiagDrv
FM: FTMApp: +%s
\\.\DiagRouter
FM: FTMApp : DIAG Driver handle Open Failed
FM: FTMApp : DIAG Driver handle Open successful
FM: FTMApp: -%s
FM: FTMApp: InitDiag: Error creating Event HANDLE, 0x%08x
FM: FTMApp: InitDiag: IOControl for IOCTL_DIAGROUTER_CMD_INIT failed,error 0x%08x
FM: FTMApp: InitDiag: IOControl for IOCTL_DIAGROUTER_CMD_INIT success
FM: FTMApp: Error: malloc failed in RegisterWithDiag
FM: FTMApp:Error: IOControl for IOCTL_DIAGROUTER_CMD_REG failed, error 0x%08x
FM: FTMApp: IOControl for IOCTL_DIAGROUTER_CMD_REG successful.
Error in allocation of Read buffer
Error in allocation of Write buffer
FM: FTMApp: WriteRspToDiag: Wrote %lu bytes to Diag
FM: FTMApp: WriteRspToDiag: Failed to write response to Diag
FM: FTMApp:Read from diag is successful, number of bytes read is %lu
FM: FTMApp:ReadDiagCmd:Error %lu in readfile
Cleanup
FM: FTMApp: Cleaning all resources
FM: FTMapp: Disable failed with error %d
FM: FTMapp: Disable successful
FM: FTMApp :Error in closing Diag driver Handle
FM: FTMApp: All resources are freed
Exiting now..
Error in release of resource..please press ctrl+break to exit
read_thread
FM: Miniport: read_thread: error in allocating memory
FM: Miniport: read_thread: Unknown event received
FM: FTMApp:+Initialize
FM: FTMapp: Error in setting console control handler
FM: FTMApp:-Initialize
FM: FTMapp: Please wait for the app to start fully..
fmrxapp.cpp
FMFTMApp :ERROR: function FAILED in line no:%d , file: %s
FM: FTMApp: Waiting for the Event to be set from DIAG
FM: FTMApp: Error %d in initializing FM
FM: FTMapp: Sending power on cmd down, time stamp %lu
FM: FTMapp: Enable failed with error %d
FM: FTMapp: Enable successful, time stamp %lu
FM: FTMapp: SetRdsGroupProcessing failed with error %d
FM: FTMapp: SetRdsGroupProcessing successful
FM: FTMapp: FM alreadyon
FM: FTMapp: SetProperty for user defined band failed with error %d
FM: FTMapp: SetProperty for user defined band successful
FM: FTMapp: ConfigUserDefinedRegion failed with error %d
FM: FTMapp: ConfigUserDefinedRegion successful
FM: FTMapp: GetStationParams failed with error %d
FM: FTMapp: GetStationParams successful
FM : FTMapp: fmParams->ulFreq is %u, g_fmctxt.region_params.bandLoLimit %u, chSpacing %u
FM: FTMapp: SetStation failed with error %d
FM: FTMapp: SetStation successful
FM: FTMapp: Sending seek cmd down, time stamp %lu
FM: FTMapp: Seek failed with error %d
FM: FTMapp: Seek successful
FM: FTMapp: CancelSeek failed with error %d
FM: FTMapp: CancelSeek successful
FM: FTMapp: SetAntennaType failed with error %d
FM: FTMapp: SetAntennaType successful
FM: FTMapp: Setting soft mute mode failed with error %d
FM: FTMapp: Setting soft mute mode successful
FM: FTMapp: SetHlsi failed with error %d
FM: FTMapp: Set notch filter failed with error %d
FM: FTMapp: Set notch filter successful
FM: FTMapp: SetMuteMode failed with error %d
FM: FTMapp: SetMuteMode successful
FM: FTMapp: SetStereoMode failed with error %d
FM: FTMapp: SetStereoMode successful
FM: FTMapp: GetPS failed with error %d
FM: FTMapp: GetPS successful, ps is %s
FM: FTMapp: Getting RDS group counters failed with error %d
FM: FTMapp: Getting RDS group counters successful
FM: FTMapp: Setting RDS Group options failed with error %d
FM: FTMapp: Setting RDS Group options successful
FM: FTMapp: GetProperty for RDS group counters failed with error %d
FM: FTMapp: GetProperty for RDS group counters successful
FM: FTMApp: Received un-supported command
FM: FTMApp: out of while loop in main, exiting ...
Reset
FM: QFM: +%s
FM: QFM: -%s
Read
FM: QFM : Read : Invalid parameter
THe QCFMFTMApp strings are getting way too long so I have attached the file for those who want to try and take a stab at decompiling the file. dotPeek nor Telerik's JustDecompile wouldn't even open it, so I don't know what's the deal with these driver level apps.

Editing any of this will result in the phone denying your editing permissions. Also, they are mostly Dword values, which cannot be written due to permissions.

DWORD or not DWORD never matters. Accessible registry entries list is more like whitelist than blacklist...

:good::good::good::good: subscribe to this thread.. hopefully dev peeps can unlock the mystery of Windows Phone

phoy18 said:
:good::good::good::good: subscribe to this thread.. hopefully dev peeps can unlock the mystery of Windows Phone
Click to expand...
Click to collapse
Same here but, the biggest problem with WP8 hacking is that. Just because you found the Key or keys to enable FM radio (As I have a Lumia 928 and pissed that there is no FM radio), does not mean you can apply them to the phone in any way.
Time will tell, Microsoft's gota slip up someplace for everyone find a hole...

ultrashot said:
DWORD or not DWORD never matters. Accessible registry entries list is more like whitelist than blacklist...
Click to expand...
Click to collapse
There must be some file that dictates the whitelist somewhere, whether its an xml file or another regfile. Another method to work this is to probably look at provxml again (I don't recall if they do any registry modification on WP8 vs WP7.) There are some tier3 applications with extra privileges (I'm not sure what they need the extra privs, or if they even have specific needs listed) that show up inside the nokia tier3 app.

What do you mean, whitelist? It's NT. The registry has ACLs (Access Control Lists) on its keys, same as on any other version of NT (from NT 3.1 to Windows 8).

It seems there will be more to this endevor than just enabling the feature. I'm seeing that there may be a bit of hardware moding we'll need to do.
Have a look at community.verizonwireless.com/thread/803729

EquiGym said:
It seems there will be more to this endevor than just enabling the feature. I'm seeing that there may be a bit of hardware moding we'll need to do.
Have a look at community.verizonwireless.com/thread/803729
Click to expand...
Click to collapse
What did it say, Verizon stripped out any hacking stuff...

DavidinCT said:
What did it say, Verizon stripped out any hacking stuff...
Click to expand...
Click to collapse
Yeah, VZW is juat a bit overly moderating. Can't even mention XDA.
Look at NeoAndersons post just before my post and also through out the thread. He's the one who got VZW to admit to the second part of the disabling.
It seems Nokia/VZW has removed the antenna wire between the chipset and the 3.5mm headphone jack.
To me, this is an easier fix than the fixing the software. I have the tools and the know how to work with hardware.
If we can get the feature reinabled on the software side, I'll be sure to work up a "how to" fix on the hardware.

I have a .pdf file of the assembly/disassembly if needed.

Please upload it, have to solve the V- button issue. It is stuck

djtonka said:
Please upload it, have to solve the V- button issue. It is stuck
Click to expand...
Click to collapse
Here you go sir. Lumia 928 Service Manual.
http://sdrv.ms/1giUqy6

tonbonz said:
Here you go sir. Lumia 928 Service Manual.
http://sdrv.ms/1giUqy6
Click to expand...
Click to collapse
Where did you end up getting that from?

Honestly I don't remember... I Google alot.

I was sure you talking about Ativ S but do not know way. Got all SM1&2 on my website anyway

djtonka said:
I was sure you talking about Ativ S but do not know way. Got all SM1&2 on my website anyway
Click to expand...
Click to collapse
Oops...well that is probably where I got the file from. I do frequent your site quite often and find it quite informative.

First Post Updated.
I've finally got the dotPeek decompiler installed and I've got more bits for 928 owners!

thals1992 said:
I've finally got the dotPeek decompiler installed and I've got more bits for 928 owners!
Click to expand...
Click to collapse
Good stuff? I swear I've been through every preinstalled .xap and the most interesting things I've found all seem to be deliberately disabled. The one diagnostics tool I got to open had no menu or picklist, just pin tile and refresh buttons. The values are there to open menus and view lists and such but it looks like the code is written either to hide or disable them. Not that I'm an expert or dev but after staring at code for hours on end you pick up on a few things and as I said in a previous post...I Google ALOT.

Not really. I just tried to look for strings with Notepad++
I just hope @ultrashot or someone with similar knowledge of developing could help me with digging into this.

[GUIDE] Build AOSP for zerofltexx by Astrubale

DELETED

but there is some aosp build usable ( incall micro working on fine ) for galaxy s 6?
thanks for the guide Master

supera3 said:
but there is some aosp build usable ( incall micro working on fine ) for galaxy s 6?
thanks for the guide Master
Click to expand...
Click to collapse
Depend on what source zero-common, zerofltexx and kernel are based.

Very cool guide, I'll have to give this a shot later just for fun! Sorry for doubting you before.

If there are new commits, before ". build/envsetup.sh" tipe "repo sync" for upgrade.

Hi @Astrubale,
I tried to build cm-13.0 with your tutorial, but build fails non-stop on:
Code:
target SharedLib: libexpat (/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/LINKED/libexpat.so)
/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/lib/xmlparse.o: file not recognized: File format not recognized
collect2: error: ld returned 1 exit status
build/core/shared_library_internal.mk:80: recipe for target '/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/LINKED/libexpat.so' failed
make: *** [/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/LINKED/libexpat.so] Error 1
make: *** Waiting for unfinished jobs....
make[3]: Nothing to be done for 'dtbs'.
or
Code:
/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libcrypto_intermediates/android_compat_hacks.o: file not recognized: File format not recognized
collect2: error: ld returned 1 exit status
build/core/shared_library_internal.mk:80: recipe for target '/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libcrypto_intermediates/LINKED/libcrypto.so' failed
make: *** [/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libcrypto_intermediates/LINKED/libcrypto.so] Error 1
make: *** Waiting for unfinished jobs....
make: Leaving directory '/home/sebek/android/system'
The solution is to remove xmlparse.o or android_compat_hacks.o and I guess it continues the build. Almost at the end of compilation (I presume) it throws out that very error and after a while I get:
Code:
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '/lib/firmware/tsp_stm/stm_z1.fw' given more than once in the same rule
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '/lib/firmware/abov/abov_valley.fw' given more than once in the same rule
make[1]: Leaving directory '/home/sebek/android/system/kernel/samsung/exynos7420'
make[1]: Entering directory '/home/sebek/android/system/kernel/samsung/exynos7420'
INSTALL net/ipv4/tcp_htcp.ko
INSTALL net/ipv4/tcp_westwood.ko
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '../../system/lib/firmware/tsp_stm/stm_z1.fw' given more than once in the same rule
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '../../system/lib/firmware/abov/abov_valley.fw' given more than once in the same rule
DEPMOD 3.10.61
make[1]: Leaving directory '/home/sebek/android/system/kernel/samsung/exynos7420'
make: Leaving directory '/home/sebek/android/system'
#### make failed to build some targets (26:29 (mm:ss)) ####
Maybe you'd be willing to give me some advice on how I could finish this build ? I am building on Ubuntu 16.04, dl'd the newest kernel from Brandon's git repo.
My best

djseban2 said:
Hi @Astrubale,
I tried to build cm-13.0 with your tutorial, but build fails non-stop on:
Code:
target SharedLib: libexpat (/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/LINKED/libexpat.so)
/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/lib/xmlparse.o: file not recognized: File format not recognized
collect2: error: ld returned 1 exit status
build/core/shared_library_internal.mk:80: recipe for target '/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/LINKED/libexpat.so' failed
make: *** [/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libexpat_intermediates/LINKED/libexpat.so] Error 1
make: *** Waiting for unfinished jobs....
make[3]: Nothing to be done for 'dtbs'.
or
Code:
/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libcrypto_intermediates/android_compat_hacks.o: file not recognized: File format not recognized
collect2: error: ld returned 1 exit status
build/core/shared_library_internal.mk:80: recipe for target '/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libcrypto_intermediates/LINKED/libcrypto.so' failed
make: *** [/home/sebek/android/system/out/target/product/zerofltexx/obj/SHARED_LIBRARIES/libcrypto_intermediates/LINKED/libcrypto.so] Error 1
make: *** Waiting for unfinished jobs....
make: Leaving directory '/home/sebek/android/system'
The solution is to remove xmlparse.o or android_compat_hacks.o and I guess it continues the build. Almost at the end of compilation (I presume) it throws out that very error and after a while I get:
Code:
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '/lib/firmware/tsp_stm/stm_z1.fw' given more than once in the same rule
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '/lib/firmware/abov/abov_valley.fw' given more than once in the same rule
make[1]: Leaving directory '/home/sebek/android/system/kernel/samsung/exynos7420'
make[1]: Entering directory '/home/sebek/android/system/kernel/samsung/exynos7420'
INSTALL net/ipv4/tcp_htcp.ko
INSTALL net/ipv4/tcp_westwood.ko
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '../../system/lib/firmware/tsp_stm/stm_z1.fw' given more than once in the same rule
/home/sebek/android/system/kernel/samsung/exynos7420/scripts/Makefile.fwinst:45: target '../../system/lib/firmware/abov/abov_valley.fw' given more than once in the same rule
DEPMOD 3.10.61
make[1]: Leaving directory '/home/sebek/android/system/kernel/samsung/exynos7420'
make: Leaving directory '/home/sebek/android/system'
#### make failed to build some targets (26:29 (mm:ss)) ####
Maybe you'd be willing to give me some advice on how I could finish this build ? I am building on Ubuntu 16.04, dl'd the newest kernel from Brandon's git repo.
My best
Click to expand...
Click to collapse
Can you send me a screen of /android/system/kernel/samsung/exynos7420/ ?

Astrubale said:
Can you send me a screen of /android/system/kernel/samsung/exynos7420/ ?
Click to expand...
Click to collapse
Sure, it looks like this:
hxxp://imgur.com/M5sAjIo
@edit: I deleted exynos7420 dir and unzipped it (dl'd zip from github) once again, this time through Terminal. Turned out it was something wrong with that, therefore I succeded with building the ROM, but my S6 hangs on "Kernel is not seandroid enforcing", after flashing the ROM (tough luck, I guess). What's more I tried flahyboy's ROM, to see if it's maybe something wrong with my S6 - well, you can say flahyboy's ROM starts instantly, but in-call mic is not working. I'd be grateful for any hints on what might be wrong. One and only thing I noticed is flahyboy's ROM is slightly greater in size (~40MB) that mine.. maybe the build solution did not add something to my zip.. Anyway - great tutorial, thanks for that. Installing AOSP just made me even more anxious to wait for making this system stable :good:

djseban2 said:
Sure, it looks like this:
hxxp://imgur.com/M5sAjIo
@edit: I deleted exynos7420 dir and unzipped it (dl'd zip from github) once again, this time through Terminal. Turned out it was something wrong with that, therefore I succeded with building the ROM, but my S6 hangs on "Kernel is not seandroid enforcing", after flashing the ROM (tough luck, I guess). What's more I tried flahyboy's ROM, to see if it's maybe something wrong with my S6 - well, you can say flahyboy's ROM starts instantly, but in-call mic is not working. I'd be grateful for any hints on what might be wrong. One and only thing I noticed is flahyboy's ROM is slightly greater in size (~40MB) that mine.. maybe the build solution did not add something to my zip.. Anyway - great tutorial, thanks for that. Installing AOSP just made me even more anxious to wait for making this system stable :good:
Click to expand...
Click to collapse
Thank, but can you compile now?

Astrubale said:
Thank, but can you compile now?
Click to expand...
Click to collapse
Yeah, I compiled it at last, but if i flash the zip from out folder, then the phone hangs on first bootsplash ("Galaxy S6") with "Kernel is not seandroid enforcing"

djseban2 said:
Yeah, I compiled it at last, but if i flash the zip from out folder, then the phone hangs on first bootsplash ("Galaxy S6") with "Kernel is not seandroid enforcing"
Click to expand...
Click to collapse
Search for errors inside /proc/last_kmsg

Wow cool clean and easy Guide. Thanks for this.
Weil try myself on that.

Astrubale said:
Search for errors inside /proc/last_kmsg
Click to expand...
Click to collapse
Code:
Samsung S-Boot 4.0 for SM-G920F (Apr 22 2016 - 16:59:51)
EXYNOS7420 EVT 1.3 (Base on ARM CortexA53)
3048MB / 0MB / Rev 11 / G920FXXU3DPDP / (PKG_ID 0x0) / LOT_ID N3N1P / RST_STAT (0x10000)
__if_pmic_rev_init - MUIC API is not ready!
MON: 0x8(1)
MON[0] = (1)[0x1c, 0x7a]
MON[1] = (2)[0x1a, 0x56]
MON[2] = (3)[0x1a, 0x3d]
MON[3] = (4)[0x1c, 0x4e]
MON[4] = (5)[0x1a, 0x39]
MON[5] = (6)[0x1a, 0x30]
MON[6] = (7)[0x15, 0x44]
MON[7] = (0)[0x0c, 0x07]
pmic_asv_init
(ASV_TBL_BASE+0x00)[11:0] bigcpu_asv_group = 2184
(ASV_TBL_BASE+0x00)[15:12] bigcpu_ssa0 = 0
(ASV_TBL_BASE+0x00)[27:16] littlecpu_asv_group = 2457
(ASV_TBL_BASE+0x00)[31:28] littlecpu_ssa0 = 0
(ASV_TBL_BASE+0x04)[11:0] g3d_asv_group = 2184
(ASV_TBL_BASE+0x04)[15:12] g3d_ssa0 = 0
(ASV_TBL_BASE+0x04)[27:16] mif_asv_group = 2184
(ASV_TBL_BASE+0x04)[31:28] mif_ssa0 = 0
(ASV_TBL_BASE+0x08)[11:0] int_asv_group = 3276
(ASV_TBL_BASE+0x08)[15:12] int_ssa0 = 6
(ASV_TBL_BASE+0x08)[27:16] cam_disp_asv_group = 2184
(ASV_TBL_BASE+0x08)[31:28] cam_disp_ssa0 = 0
(ASV_TBL_BASE+0x0C)[3:0] dvfs_asv_table_version = 15
(ASV_TBL_BASE+0x0C)[4] asv_group_type = 0
(ASV_TBL_BASE+0x0C)[7:5] reserved01 = 0
(ASV_TBL_BASE+0x0C)[8] shift_type = 0
(ASV_TBL_BASE+0x0C)[9] ssa1_enable = 0
(ASV_TBL_BASE+0x0C)[10] ssa0_enable = 1
(ASV_TBL_BASE+0x0C)[15:11] reserved02 = 0
(ASV_TBL_BASE+0x0C)[16] asv_method = 1
(ASV_TBL_BASE+0x0C)[31:17] reserved03 = 0
(ASV_TBL_BASE+0x10)[3:0] main_asv_group = 0
(ASV_TBL_BASE+0x10)[7:4] main_asv_ssa = 0
(ASV_TBL_BASE+0x10)[11:8] bigcpu_ssa1 = 0
(ASV_TBL_BASE+0x10)[15:12] littlecpu_ssa1 = 0
(ASV_TBL_BASE+0x10)[19:16] g3d_ssa1 = 0
(ASV_TBL_BASE+0x10)[23:20] mif_ssa1 = 0
(ASV_TBL_BASE+0x10)[27:24] int_ssa1 = 0
(ASV_TBL_BASE+0x10)[31:28] cam_disp_ssa1 = 0
(ASV_TBL_BASE+0x14)[8:0] bigcpu_ssa_ema = 0
(ASV_TBL_BASE+0x14)[17:9] littlecpu_ssa_ema = 0
(ASV_TBL_BASE+0x14)[26:18] g3d_ssa_ema = 0
(ASV_TBL_BASE+0x14)[31:27] reserved04 = 0
chip_status = f, bin2_efuse = 0
muic_register_max77843_apis
muic_is_max77843 chip_id:0x43 muic_id:0xb5 -> matched.
MUIC rev = MAX77843(181)
init_multi_microusb_ic Active MUIC 0xb5
max77843_init_microusb_ic: MUIC: CDETCTRL:0x2d
max77843_init_microusb_ic: MUIC: CONTROL1:0x00
max77843_init_microusb_ic: MUIC: CONTROL2:0x3b
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_muic_get_chg_typ: STATUS2:0x00
max77843_muic_get_chg_typ: CHGTYP:0x00
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_muic_get_chg_typ: STATUS2:0x00
max77843_muic_get_chg_typ: CHGTYP:0x00
load Secure Payload done.
Chip ID : 060f4d16dd28 / 0x00007700
EL3 monitor information => Built : 16:48:28, Jan 18 2016
bConfigDescrLock: 1
sw_lock success
sw_lock success
sw_lock success
SCSI CMD : 55 11 00 00 00 00 00 00 14 00
SCSI Response(01) : Target Failure
SCSI Status(02) : max77843_set_muic_uart_early: MUIC: CONTROL1: 0x00
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
[Debug Info.]
S-BOOT : VERSION_-+F0
SecureOS : 20 (MB)
- read_bl1
blk_bread_bootsector: LUN 1, from 0x0, size 0x10, buffer 0x45708000
Verify_Binary_Signature 0x45720120 [email protected], [email protected]
pit_check_signature (PIT) valid.
PARAM ENV VERSION: v1.0..
blk_bread_bootsector: LUN 1, from 0xffe, size 0x1, buffer 0x441204c0
initialize_ddi_data: usable! (3:0xf), warranty reason : (0x0303)
MAGIC_RAM_BASE: 4000000, MAGIC_RAM_BASE2: 100001, ompin: 2000a
[ldfw] Pass LDFW partition!
[ldfw] read whole CM partition from the storage
ldfw: 0th ldfw's version 0x20151027 name : CryptoManagerV20
ldfw: 1th ldfw's version 0x20151203 name : fmp_fw
ldfw: init ldfw(s). whole ldfws size 0x204110
[ldfw] try to init 2 ldfw(s). except 0 ldfw 2 ldfw(s) have been inited done.
[mobi_drv] add: 0x43e71940, size: 11401
MobiCore IDLE flag = 0
MobiCore Driver loaded and RTM IDLE!
[OTP] 27 bit read: 0x5
[OTP] 22 bit read: 0x0
[OTP] 21 bit read: 0x0
[OTP] 23 bit read: 0x1
[OTP] 26 bit read: 0x1
[OTP] NANTIRBK0 bit reading: start
[OTP] NANTIRBK0: 3 bit
[OTP] 28 bit read: 0x1
[OTP] 29 bit read: 0x0
[OTP] 30 bit read: 0x1
[OTP] 25 bit read: 0x1
[OTP] ETC value: 0
[EFUSE] SMC Read the 0x0 ...
[EFUSE] SMC Read Count value: 3
[EFUSE] SMC Read the 0x1 ...
[EFUSE] SMC Read Count value: 1
[EFUSE] SMC Read the 0x2 ...
[EFUSE] SMC Read Count value: 0
[EFUSE] SMC Read the 0x3 ...
[EFUSE] SMC Read Count value: 1
(1,5) vs (1,5)
[EFUSE] This is commercial device.
set_tzpc_secureport: successfully protected 0
eSE Protection!!
Authenticated data read request (Swapped)
Authenticated data read response (Swapped)
RPMB: get hmac value: success
HMAC compare success !!
update_rpmb_version skip.
initialize_secdata_rpmb: usable! (0x52504d42)
DDR SIZE: 3G (0xc0000000)
LPDDR4 manufacturer : Micron
bin2_efuse = 0
[TMU] 52, 53, 51, 51
UFS vendor: SAMSUNG
FW rev : 0200
product : KLUBG4G1BD-E0B1
UFS size (GB) : 32
UFS ID : XXXXXXXXXXXXXXXX
lun:196 Query Response : 0xfc
lun:196 Query Response : 0xfc
lun:196 Query Response : 0xfc
lun:196 Query Response : 0xfc
dNumAllocUnits error at LU7 0 0
PROVISION : FAIL
PROVISION : FAIL
max77843_muic_api_print_init_regs: INTMASK[1:0x00, 2:0x00, 3:0x00]
max77843_muic_api_print_init_regs: MUIC: CDETCTRL:0x2d
max77843_muic_api_print_init_regs: MUIC: CONTROL1:0x00
max77843_muic_api_print_init_regs: MUIC: CONTROL2:0x3b
max77843_muic_api_print_init_regs: MUIC: CONTROL3:0x00
max77843_muic_api_print_init_regs: MUIC: CONTROL4[0x16]:0xb2
init_ific : MAX77843(0)
init_ific : MAX77843(0)
set_float_voltage: max77843 battery cv voltage 0x9c
set_charger_state: buck(1), chg(1), reg(0x05)
max77843_get_charger_status: Invalid charger
set_auto_current: get_charger_status(0)
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_muic_get_chg_typ: STATUS2:0x00
max77843_muic_get_chg_typ: CHGTYP:0x00
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_muic_get_chg_typ: STATUS2:0x00
max77843_muic_get_chg_typ: CHGTYP:0x00
get_wireless_charger_detect: wireless check 0
get_wireless_charger_detect : CHG_DTLS(0x00)
set_auto_current: unknown_state, curr(475)
max77843_get_charger_status: Invalid charger
get_wireless_charger_detect: wireless check 0
get_wireless_charger_detect : CHG_DTLS(0x00)
set_charger_current: chg curr(137), in curr(0)
max77843_get_charger_status: Invalid charger
get_wireless_charger_detect: wireless check 0
get_wireless_charger_detect : CHG_DTLS(0x00)
fuelguage : wpc_status(0)
set_charger_state: buck(1), chg(0), reg(0x04)
init_fuel_gauge: Start!!
init_fuel_gauge : MAX77843(0)
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
adc_read_temp temp_adc = 1852
init_fuel_gauge temp = 25
init_fuel_gauge : MAX77843(0)
init_fuel_gauge: Battery type : SDI, capacity: 5177, status: 128
init_fuel_gauge: Already initialized (0x1439, SDI type)
check_validation_with_tablesoc: Start!!
fuel_gauge_read_soc: SOC(32), data(0x209a)
fuel_gauge_read_ocv: VFOCV(3774), data(0xbcba)
calculate_table_soc : low(0) high(6) mid(7) table_soc(0)
calculate_table_soc : low(4) high(6) mid(3) table_soc(0)
calculate_table_soc : low(6) high(6) mid(5) table_soc(0)
calculate_table_soc : low(7) high(6) mid(6) table_soc(0)
calculate_table_soc: vcell [3774] table_soc [31]
differ(1), table_soc(31), RepSOC(32)
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_muic_get_chg_typ: STATUS2:0x00
max77843_muic_get_chg_typ: CHGTYP:0x00
fuel_gauge_read_vcell: VCELL(3716), data(0xb9d8)
vcell(3716),soc_diff_limit(50), low_temp_reset(0)
fuel_gauge_read_ocv: VFOCV(3774), data(0xbcba)
fuel_gauge_read_vcell: VCELL(3716), data(0xb9d8)
fuel_gauge_read_soc: SOC(32), data(0x209a)
fuel_gauge_read_vfsoc: VFSOC(30), data(0x1ef3)
init_fuel_gauge : OCV(3774), VCELL(3716), SOC(32), VFSOC(30)
AP_PMIC_SDA = 1
PMIC_ID = 0x12
OTP:0x78 PWR_SEQ:1 G3D_OCP:1 PSoff:1 INT_Volt:1
PMIC_STATUS1 = 0x2f PWRON JIGONB ACOKB MR2B PWRON1S
PMIC_STATUS2 = 0x11 RTC60SE RTC1SE
PMIC_PWRONSRC = 0x08 MRST
PMIC_OFFSRC = 0x00
PMIC_INT1 = 0xc3 PWRONF PWRONR PWRON1S MRB
PMIC_INT2 = 0x11 RTC60S RTC1S
PMIC_INT3 = 0x80 RSVD
PMIC_RTC_CTRL = 0x02
PMIC_RTC_SMPL = 0x83
RTC TIME: 2016-08-13 07:27:29(0x40)AM
s5p_check_keypad: 0x10110000
s5p_check_keypad: recovery mode
set_oneshot_recovery: recovery mode set! sys_bootm=0x80000
s5p_check_reboot_mode: INFORM3 = 0 ... skip
ATLAS_PLL = 1200MHz APOLLO_PLL = 1200MHz MIF_PLL = 3104MHz
MFC_PLL = 468MHz CCI_PLL = 532MHz
BUS0_PLL = 1600MHz BUS1_PLL = 668MHz
board_uart_rustproof ifc_sense: 0
-user build & not FAC
-rustproof mode Enabled
s5p_check_upload: MAGIC(0x4000000), RST_STAT(0x10000)
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
s5p_check_upload: debug level is LO! (mask: 0x220)
max77843_ific_set_mrstb: TOPSYS: MAINCTRL1[0x02]: [0x07]+[0x07]->[0x07]
s5p_check_upload: disable dump_gpr
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
s5p_check_download: 0
max77843_muic_get_adc_value: STATUS1:0x1f
max77843_muic_get_adc_value: ADC:0x1f
max77843_get_charger_status: Invalid charger
get_wireless_charger_detect: wireless check 0
get_wireless_charger_detect : CHG_DTLS(0x00)
check_pm_status: charger is not detected
fuel_gauge_read_vcell: VCELL(3718), data(0xb9ea)
check_pm_status: voltage(3718) is ok
check_pm_status: 7 sec reset, continue.
scr_draw_image: draw 'logo.jpg'...
read 'logo.jpg'(112504) completed.
board_set_dev_pm: s2mpb02 enable for display
42, 0, 13, 0x420013
DETECTED LCD TYPE : S6E3HA2
mipi-dsi driver(CMD mode) has been probed.
decon-int: ver0, max win7, command mode, hw trigger
single dsi mode
decon0 registered successfully
afw flag is Unknown [afw flag : 00 00 00 00]
secure info base: 45720000 and SMC Num = 0x83000013
secure smc success!!! [ret = 0]
Set debug level to low(4f4c)
DMV: Successfully informed TZ of boot mode: Recovery
load_kernel: loading boot image from 139264..
kernel size = 0x114f000, ramdisk size = 0x5fc000
dt_size:1454080, dt_actual:1454080
Verify_Binary_Signature 0x45720120 [email protected], [email protected]
Kernel Image
Verify_Binary_Signature: failed.(-18022398)
pit_check_signature (RECOVERY) invalid.
[TIMA trusted boot]: SEANDROID ENFORCING
Set invalid sign flag
No need to update kernel type.
[EFUSE] warranty bit is already set.
ace_hash_sha_digest: passed.(0)
tboot ctx base: 45720248
SMC Num = 0x83000001
mobismc success!!! [ret = 0]
SMC Num = 0x83000007
mobismc for tima info success!!! [ret = 0]
Pass. DTBH size is smaller than a page.
<dtbh_header Info>
magic:0x48425444, version:0x00000002, num_entries:0x00000008
<device info>
chip_id: 0x00001cfc
platform_id: 0x000050a6
subtype_id: 0x217584da
hw_rev: 0x0000000b
dt_entry[06]
chip_id: 0x00001cfc
platform_id: 0x000050a6
subtype_id: 0x217584da
hw_rev: 0x0000000a
hw_rev_end: 0x0000000b
offset: 0x0010a000
dtb size: 0x0002c800
Selected entry hw_ver : 11
dt_entry of hw_rev 10 is loaded at 0x4a000000.(182272 Bytes)
[EFUSE] RB count: device(0x3), binary(0x3)
[OTP] SW LOCK Success
DDI value :0x0000000f
sw_lock success
sw_lock success
Forced Enable KAP
Warranty Bit Set - Blowing KAP_VIOLATION_FUSE
KAP status = 5afe0003
ATAG_CORE: 5 54410001 0 0 0
ATAG_MEM: 4 54410002 20000000 40000000
ATAG_MEM: 4 54410002 20000000 60000000
ATAG_MEM: 4 54410002 20000000 80000000
ATAG_MEM: 4 54410002 20000000 A0000000
ATAG_MEM: 4 54410002 20000000 C0000000
ATAG_MEM: 4 54410002 1E800000 E0000000
ATAG_SERIAL: 4 54410006 XXXXXXXX XXXXXXXX
ATAG_INITRD2: 4 54420005 43000000 5fbd8f
ATAG_REVISION: 3 54410007 b
check_rustproof [0,0] On
ucs flag is Unknown
ucs flag : 00 00 00 00
ATAG_CMDLINE: f0 54410009 'console=ram loglevel=4 bootmode=2 sec_debug.level=0 sec_watchdog.sec_pet=5 androidboot.hardware=samsungexynos7420 androidboot.debug_level=0x4f4c ess_setup=0x46000000 [email protected] [email protected] charging_mode=0x3000 s3cfb.bootloaderfb=0xe2a00000 sysscope=0x6b090719 lcdtype=4325395 consoleblank=0 lpj=239616 sec_debug.reset_reason=5 ehci_hcd.park=3 oops=panic pmic_info=35 cordon=c34c0eba5576148dc662cf43a6352c3b connie=SM-G920F_OPEN_EUR_c3811d70601ea690b7b0b2afca80be2c fg_reset=0 androidboot.emmc_checksum=3 androidboot.boot_salescode= androidboot.odin_download=1 androidboot.bootloader=G920FXXU3DPDP androidboot.selinux=enforcing androidboot.security_mode=1526595585 androidboot.ucs_mode=0 androidboot.hw_rev=11 androidboot.warranty_bit=1 androidboot.hmac_mismatch=0 androidboot.sec_atd.tty=/dev/ttySAC1 androidboot.serialno=XXXXXXXXXXXXXXXX snd_soc_core.pmdown_time=1000 zero_sdchg_ic=0 androidboot.fmp_config=0'
ATAG_NONE: 0 0
pack_atags: ramdisk size start 0x43000000, size 0x5fbd8f
Updating device tree @0x4a000000: done
Starting kernel at 0x40205000...
SWITCH_SEL(3)
BOOTING TIME : 2895
Here it is, mate. I can't seem to find anything suspicious besides
Code:
dNumAllocUnits error at LU7 0 0
PROVISION : FAIL
PROVISION : FAIL
but I can only guess

Hi I am having problems compiling due to the kernel. Which kernel source should I use? How should I configure it? Help pleaase

Added "extract files" guide.

Whenever I try to download the CyanogenMod repo, I get this error:
error: Exited sync due to fetch errors
I've tried using: repo sync -f and: repo sync --force-sync
I'm trying to download the CM13 repo.
I've also followed the steps exactly as they were written.

I'm trying to build cm-14.0. Fails at
HTML:
Starting build with ninja
ninja: Entering directory `.'
ninja: error: '/home/julian/android/system/out/target/product/zerofltexx/obj_arm/SHARED_LIBRARIES/libsecril-client_intermediates/export_includes', needed by '/home/julian/android/system/out/target/product/zerofltexx/obj_arm/SHARED_LIBRARIES/audio.primary.universal7420_intermediates/import_includes', missing and no known rule to make it
build/core/ninja.mk:151: recipe for target 'ninja_wrapper' failed
make: *** [ninja_wrapper] Error 1
make: Leaving directory '/home/julian/android/system'
.
Any ideas what could be wrong?
/android/system/kernel/samsung/exynos7420 contains github.com/CyanogenMod/android_kernel_samsung_exynos7420 cm-14.0.
Thanks for the great guide anyway

[HELP] Z00TD/ZE551KL stuck in EDL mode, unsure what to do.

I have a Zenfone 2 Laser (ZE551KL) and it's currently stuck in EDL mode. The bootloader was locked when this happened, and the phone was running stock Android M rom. I'm not sure what happened, but I can guarantee it is not a hardware failure.
When I first plugged the phone in and ran EDL, the partition table (edl printgpt) was empty. After I went, grabbed the firmware and the GPT file (I tried gpt_main, gpt_backup, and gpt_both, same end result) and flashed it, I get the following:
Code:
$ edl printgpt
Parsing Lun 0:
GPT Table:
-------------
sbl1: Offset 0x0000000000004400, Length 0x0000000000140000, Flags 0x0000000000000000, UUID b6e183fd-7e32-6aab-45a0-95aa05d488ff, Type 0xdea0ba2c, Active False
DDR: Offset 0x0000000000144400, Length 0x0000000000008000, Flags 0x1000000000000000, UUID 12145d01-36e4-dabb-43ee-d41814020b99, Type 0x20a0c19c, Active False
rpm: Offset 0x000000000014c400, Length 0x0000000000080000, Flags 0x0000000000000000, UUID a6cde2ba-f246-d267-4e32-27a784384929, Type 0x98df793, Active False
tz: Offset 0x00000000001cc400, Length 0x0000000000080000, Flags 0x0000000000000000, UUID 65484ccf-89c1-6697-724e-ca807a503232, Type 0xa053aa7f, Active False
aboot: Offset 0x000000000024c400, Length 0x0000000000500000, Flags 0x1000000000000000, UUID d85a0017-ca5e-5ae5-7501-e91c6e879873, Type 0x400ffdcd, Active False
hyp: Offset 0x000000000074c400, Length 0x0000000000080000, Flags 0x0000000000000000, UUID e8e93198-beea-0f83-ba35-62b457a963c2, Type 0xe1a6a689, Active False
Total disk size:0x0000000000004400, sectors:0x0000000000000022
I made sure to flash all the partitions using the appropriate files from the latest firmware from ASUS's website. (sbl1 = sbl1.mbn, etc.)
Unfortunately, the phone simply didn't boot. I tried a final "hail mary" of sorts, and I ran the command "edl setbootablestoragedrive 0". The command returned success, but unfortunately, nothing changed.
Any help is appreciated, thanks in advance.